ahmed_hebeshe_cv
TRANSCRIPT
![Page 1: Ahmed_Hebeshe_CV](https://reader036.vdocument.in/reader036/viewer/2022092622/587b2aab1a28ab057d8b4f79/html5/thumbnails/1.jpg)
Ahmed Hebeshe Instrumentation and Control Engineer
Personal Profile
Objective Contact Information
Seeking challenging position in
Engineering field where I can share
my skills. My experience in PLC
Programming and Industrial
Communications will be very helpful,
also looking for learning more and
developing my skills.
(002) 0100 429 3269
21 El Falaky St., El Ghareb, Suez, Egypt.
www.ahmedhebeshe.eu5.org
www.linkedin.com/in/ahmedhebeshe
Personal Information
Date of birth September 1st, 1986. Military service Exempted.
Nationality Egyptian. Marital status Married.
Professional Experience
May 2013 Instrumentation and Control Engineer.
To Present at Egyptian Indian Polyester (EIPET).
Responsible for following up Instrumentation maintenance job and
troubleshooting problems.
Responsible for Troubleshooting PLC Problems, Performing
Software Editing if required.
Responsible for following up the Installation, Commissioning and
start-up of project during construction.
July 2011 Electrical and Instrumentation Engineer.
To May 2013 at Egyptian International Gas Technology (GASTEC).
Responsible for following up Electrical and Instrumentation
maintenance job and troubleshooting problems.
Responsible for Troubleshooting PLC Problems, Performing
Software Editing if required.
Successfully Managed the Installation, Commissioning and start-up
of Two gas stations construction projects (Port-fouad and Suez 3 Gas
stations).
December 2010 Electrical and Instrumentation Engineer
To July 2011 at Ceramica Cleopatra.
Responsible for following up Electrical and Instrumentation
maintenance job and troubleshooting problems.
![Page 2: Ahmed_Hebeshe_CV](https://reader036.vdocument.in/reader036/viewer/2022092622/587b2aab1a28ab057d8b4f79/html5/thumbnails/2.jpg)
Selected Achievements Full programming of Water treatment plant in EIPET Including PLCs and HMIs from zero
level during the construction of the plant which saved company Time and money, the plant is
working perfectly.
Full programming of Packing Area SCADA System in EIPET, the system is able to monitor
full data of 6 packing lines and it can send daily report to management and to whom concern,
the connection was done with MODBUS protocol.
Preventing Port-Said El-Herafeen station in Gastec from shutdown for may be one month
because of severe damage in control HMI, this type of HMI is obsolete, and we were
supposed to wait until Stock HMI reaches from Argentina, My Solution was modifying the
HMI to other available type of HMI in 6 Hours and successfully running station again.
Technical Skills
Dealing with different types of PLCs like Siemens SIMATIC S7 200, S7 300, ET200S, S7
1200, and Modicon PLCs.
Dealing with different types of instrumentations:
- Pressure switches, Transmitters with different types.
- Level transmitters with different types, like guided wave radar, radioactive,
Displacer, Bubbler, and Float.
- Temperature sensors RTDs, PT100 and Thermocouples.
- Flow transmitters with different types, like magnetic, coriolis, differential pressure,
Vortex, Rotameters, Orifice, and Annubar.
- Control Valves, Positioners, ON-OFF valves and Solenoids.
- Vibration transmitters, Switches and Gas Detectors.
- Gas analyzers (Oxygen and Hydrogen analyzers).
- Viscosity meters
- Pneumatic Pistons.
Dealing with different Fitting types, Different thread types (NPT and BSP), Tube Fittings.
Dealing with HART Communicator.
Dealing with Charts (P&ID, Hook Up, Nozzle orientation, Isometrics, and Instrumentation
location layout).
Communication protocols (Modbus, Profibus and Profinet).
HMIs (Siemens SIMATIC TP and OP panels).
“HAZOP” study.
Explosion proof systems.
Dealing with DCS (Yokogawa CENTUM VP).
Dealing with instruments from Different Manufacturers like Endress+Hauser, ABB,
Siemens, Samson, Emerson, Festo and Yokogawa.
Designing of PIC microcontrollers.
![Page 3: Ahmed_Hebeshe_CV](https://reader036.vdocument.in/reader036/viewer/2022092622/587b2aab1a28ab057d8b4f79/html5/thumbnails/3.jpg)
Soft Skills
Motivate others.
Problem solving.
Decision making.
Working under pressure.
Team leading.
Creativity.
Computer Skills
Operating systems Linux (Ubuntu 15.10 or older) and Windows.
Drawing AUTOCAD (2D, 3D and Electrical drawing), Smart Draw.
Programming Good knowledge Web sites programming (php and MySQL).
Office Microsoft office (Word, PowerPoint, Excel, Access).
Languages Arabic (Mother Tongue). English.
Education and Training
Bachelor of Electrical Power & Control Engineering. 2010 Faculty of Engineering, Alexandria University, Egypt.
PLC Training Course
2010 , Alexandria, Egypt.
HAZOP Study
2012 British international center for training and consultations
References
Name Company Position Contact
Eng.Tarek Bakr EIPET Instrumentation manager (002) 0102 609 1910
Eng. Sreenivas Reddy Yokogawa System Design manager (0091 ) 9346 003 456
Eng. Mohamed Amen ENPPI Project QC Manager (002) 0100 872 6190
Certificates are available upon request.