aii37661 2008 civic 2&4 dr xm radio ... - college hills honda · 2006-2008 civic xm radio...

© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 37661 (0708) 1 of 11

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

AII 37661

Issue Date

AUG 2007

2006-2008 CIVIC2- AND 4-DOOR (EX)XM RADIO SYSTEM

PARTS LIST

XM Radio Attachment (sold separately):P/N 08B15-SNA-100A

Bus cable

Bracket

Turn nut

Clip

Rubber pad

4 Pan screws

4 Washers

Flange bolt

Washer-screw

Cover seal

6 Wire ties

2 Wire ties with clips

6 Cushion tapes

3 EPT sealers

XM Antenna (sold separately):P/N 08A15-0J1-100

Antenna

XM Radio Unit (sold separately):P/N 08A15-3J1-000

XM® Satellite Radio unit

Y-Adapter Harness (sold separately):P/N 08A31-0F1-000

Y-Adapter harness

08B15-SNA-1A00-91

www.collegehillshonda.com

2 of 11 AII 37661 (0708) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.

TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverUtility knifeShop towelScissorsRatchet8 mm, 10 mm, and 14 mm Socket8 mm, 10 mm, and 14 mm Combination wrenchesIsopropyl alcohol (Isopropyl alcohol, in a 60/40 solution

with water)Rubber malletMasking tapeFelt-tip penTORX bitDrill3 mm and 8 mm Drill bitsEye protectionRuler

Illustration of the XM Radio System Installed onthe Vehicle

6621020H

AUDIO UNIT

ANTENNA

XM RADIOUNIT

BUS CABLE

5306360T

PASSENGER’SDASHBOARDUNDER COVER

4 CLIPS

2 PINS

6622060H

ANTENNA

BUS CABLE

XM RADIOUNIT

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

3. Remove the passenger’s dashboard under cover(four clips and two pins).



5202121T

8 CLIPS

DRIVER’SDASHBOARDLOWER COVER

4. Remove the two bolts under the glove box. 7. Remove the inside cover from the front consolepocket (two tabs).

8. Lower the tilt lever, then pull the steering wheeltoward you.

9. To protect the dashboard area, put shop towelsover the steering wheel and shift lever.

5202130T

FRONT CONSOLEPOCKET

INSIDECOVER

2 TABS

SHIFT LEVER“S" or" 2”POSITION

5608031H

SHOPTOWEL

STEERINGWHEEL

SHOP TOWEL

COMBINATIONSWITCH

SHIFTLEVER

TILT LEVER

5. Open and remove the glove box (two stops).

6. Remove the driver’s dashboard lower cover (eightclips).

5202260T

BOLT

GLOBE BOX2 STOPS



12. Remove the weatherstrip in the area shown.

5718021H

FRONT PILLAR

PIN

CLIP

RUBBER MALLETStrike perpendicularly.

WEATHERSTRIPRIGHT FRONTPILLAR TRIM

CLIP

FRONTPILLAR TRIM

10. Apply masking tape to the meter panel as shown,and remove the meter panel (one self-tappingscrew, 11 clips, and vehicle connectors).

11. Apply masking tape to the instrument panel asshown. Remove the center panel (two bolts, tenretaining clips, vehicle connectors, and aspiratorhose).

5202563T

5 CLIPS

BOLTS

VEHICLECONNECTORS

6 CLIPS

MASKING TAPE

CENTER PANEL

ASPIRATORHOSE

13. Push the clip into the vehicle side by striking thetop of the right front pillar trim in the part markedSIDE CURTAIN AIRBAG with the rubber mallet.Remove the clip.

6719010H

SELF-TAPPINGSCREW

11 CLIPS

METER PANEL MASKINGTAPE

VEHICLECONNECTOR

VEHICLECONNECTOR(if equipped)



15. Remove the cap from the right sunvisor (fourretaining tabs).

5321090H

CONNECTOR

4 RETAININGTABS

CAP

TORX SCREW

RIGHT SUNVISORSUNVISORHOLDER

5202250T

RIGHT FRONTPILLAR TRIM2 CLIPS

WEATHERSTRIP

14. Remove the weatherstrip in the area shown. Thenremove the right front pillar trim (two clips).

4-Door:

16. Remove the right sunvisor (two T25 TORXscrews, and unplug the vehicle connector).

17. Remove the sunvisor holder. Turn the holder 90°,then pull it out.

18. Remove the right front door sill trim (three tabs,five clips, and five hooks).

5425040H

RIGHT FRONTPILLAR TRIM

2 CLIPS

WEATHERSTRIP

2-Door:

5202210T

FRONT

RIGHT FRONTDOOR SILL TRIM

5 CLIPS

TAB

HOOK

TAB

TAB

HOOKS



21. Using isopropyl alchohol on a shop towel, cleanthe area shown where the rubber pad will attach.Attach the rubber pad to the vehicle panel.

22. 2-Door only: While wearing eye protection, drillthrough the dimple on the vehicle panel with a 3mm drill bit and then finish with an 8 mm drill bit.Use a drill stop to avoid drilling through the innerpanel.

6621050H

DRILL BIT

VEHICLEPANEL

DIMPLE

3 mm and then8 mm DRILL BITS

DRILLMOTOR

DUCTTAPE

10 mm

6621040H

GLOVE BOXOPENING

BACKING

RUBBERPAD

6 mm

RUBBER PAD

18 mm

VEHICLEPANEL

Installing the XM Radio Unit

20. Using four pan screws and four washers, securethe bracket to the XM radio unit.

19. Remove the weatherstrip, then remove the rightkick panel (two clips).

5202230T

WEATHERSTRIP2 CLIPS

RIGHT KICK PANEL

6621030H

4 WASHERS4 PAN SCREWS

BRACKET

XM RADIOUNIT



23. Using one flange bolt, one turn nut, and onewasher-screw, secure the XM radio unit andbracket to the vehicle stay and to the vehiclepanel.

6621060HXM RADIOUNIT

TURNNUT

WASHER-SCREW

BRACKET

VEHICLE STAY

FLANGEBOLT

VEHICLEPANEL

SQUARE HOLEOR 8 mmDRILLED HOLE

Routing the Antenna Cable

24. Using isopropyl alcohol on a shop towel, clean theright front upper corner on the inside of thewindshield.

25. Remove the adhesive backings from the antenna,and attach the antenna to the windshield at thelocation shown. Install the antenna by applyingsufficient pressure.

6724010H

10 mm

3 mm

ANTENNA

INSIDE

ANTENNA

WINDSHIELD 4 ADHESIVEBACKINGS



29. Route the antenna cable down to the XM radiounit.

6621080H

BUS CABLE14-PINCONNECTOR

XM RADIOUNIT

ANTENNACABLE 1-PINCONNECTOR

6621071HEPT SEALER (1/2)

ANTENNACABLE

VEHICLEHARNESS

VEHICLEBRACKET

DASHBOARDSTAY

EPT SEALERCut in half.

5321132H

ADHESIVEBACKING

COVERSEAL

OUTSIDE

“ ” MARKon the frontwindow

5 mm

5 mm

26. Using isopropyl alcohol on a shop towel, clean thearea shown on the outside of the windshield.

27. Remove the adhesive backing from the cover sealand attach it to the outside of the windshield in thelocation shown.

28. Route the antenna cable down along thepassenger’s A-pillar. Using six cushion tapes,secure the antenna cable to the A-pillar panel inthe areas shown.

6622070H

6 CUSHIONTAPES

ANTENNACABLE

ANTENNA

PASSENGER’SA-PILLAR

30. Using scissors, cut one EPT sealer in half.

31. Using isopropyl alchohol on a shop towel, cleanthe area where the EPT sealer will attach. Attachone cut piece of EPT sealer to the vehicle bracketas shown.

32. Plug the antenna cable 1-pin connector and thebus cable 14-pin connector into the XM radio unit.



33. Attach the other cut piece of EPT sealer to theantenna cable as shown.

34. Using two wire ties with clips, secure the antennacable and the bus cable to the bracket holes asshown.

35. Using one wire tie, secure the bus and antennacables to the vehicle harness in the area shown.

36. Route the bus cable up along the antenna cable.Using two wire ties, secure the bus and antennacables to the vehicle harness.

6622011HBRACKET HOLE

BUSCABLE

ANTENNACABLE

XM RADIOUNIT

WIRETIEWITHCLIP

EPT SEALER (1/2)

WIRETIE

VEHICLEHARNESS

BRACKETHOLE

6622021H

GLOVE BOXOPENING

WIRETIE

VEHICLEHARNESSBUSCABLE

ANTENNACABLE

BUSCABLE

37. In the glove box opening, route the bus cablealong the vehicle harness and towards the audiounit opening.

38. Using two wire ties, secure the bus cable to thevehicle harness.

39. Using one wire tie, secure the bus cable to thevehicle harness in the area shown.

6622030H

VEHICLEHARNESS

WIRE TIE

BUS CABLE

6622040H

BUS CABLECONNECTOR

WIRE TIE

VEHICLEHARNESS

BUSCABLE

AUDIO UNITOPENING



BUS CABLE ORY-HARNESSADAPTER

AUDIO UNIT

6724040H

If the vehicle you’re working on is equipped with aCD changer, continue with step 40; otherwise, go tostep 42.

40. Plug the Y-harness adapter connectors into thetwo bus cables.

41. Using two EPT sealers, wrap the two pluggedconnectors.

6622050H

Y-HARNESSADAPTER

BUS CABLE

2 EPT SEALERS

42. Plug the bus cable connector into the audio unit(or navigation unit, if equipped).

4-Door:

2-Door:

With Navigation Unit

5801010H


AUDIO UNIT

5801030H


NAVIGATIONUNIT



43. Connect the vehicle connectors to the centerpanel, and reinstall the center panel.

44. Replace the old clip on the right front pillar trimwith the new clip included in the kit.

5323070H

NEW CLIP

OLD CLIP(Discard.)

RIGHT FRONTPILLAR TRIM

5420071H

CENTER PANEL

VEHICLE CONNECTORS

BOLT(reused.)

45. Check that all wire harnesses are routed properlyand all connectors are plugged in.

46. Reconnect the negative cable to the battery.

47. Enter the customer’s radio anti-theft code, andreset the radio station presets.

48. Set the clock.

49. Check the operation of the XM radio systemaccording to the vehicle’s Owner’s Manual.

50. Reinstall all removed parts.


aii37661 2008 civic 2&4 dr xm radio ... - college hills honda · 2006-2008 civic xm radio...

Documents