air cooled diesel engines - kohlerpower.it · air cooled diesel engines standard equipment recoil...
TRANSCRIPT
AIR COOLEDDIESEL ENGINES
STANDARD EQUIPMENT
Recoil starting with automatic compression release §
Fuel tank
Fuel filter
Dry air cleaner
Muffler with guard
Accelerator and stop manual control
Manual compression release*
Automatic deaeration on injection pump
Wire mesh oil filter
Conical power take-off
External safety fuel filter
Automatic fuel control during start
User maintenance and spare parts booklet
Specific for KD15 440 model:
Hydraulic tappets
High capacity dry air cleaner
Fuel tank drain tap
3 years extended warranty
§ Not on KD 500 model* On KD 500 model only
ACCESSORIES ON DEMANDPower take-off flywheel side (engines with electrical starting)
Power take-offs with flanging and special shaft
Lateral power take-off*
Internal dynamic balancer
Electric start 12V / 24 V
Keyswitch panelFuel lift pump
Emergency stop through electrovalve
Accelerator and stop remote control
Oil pressure switch
Oil temperature switch
Oil bath air cleaner
Cylinder head temperature switch
Glow plug on intake manifold
Stop with solenoid valveRecoil with denoising cover
Grass protection for engine cooling
Alternator with voltage regulator 12 V or 24 V
Oil level sensor switch
Oil refill on cranckase side
High capacity oil sump(KD 350 and KD15 440)
High capacity oil and fuel filters for remote assembly
Internal fuel pre-filter
Cyclonic air intake pre-filter
Single lever control
Control lever guard
Air filter clogging indicator, integrated into the engine construction form
External spin on oil filter
Specific for KD15 440 model:
Quick specifics
CYLINDERS 1
MAX POWER kW (hp)@rpm
3.5 (4.8) @ 3600
MAX TORQUE Nm@rpm
10.4 @ 2400
KD225
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 -IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
358177 181
417
130
47.5 7439
R5. 512.5 5
265
95 115Ø11 N°2 holes
47.5 7439
R5. 512.5 5
265
95 115Ø11 N°2 holes
358177 181
130
47.5 7439
R5. 512.5 5
265
95 115Ø11 N°2 holes
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
210
230
250
270
290
6.0
7.0
8.0
9.0
10.0
11.0
1.0
1.5
2.0
2.5
3.0
3.5
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
0.6
0.7
0.8
0.9
1.0
1.1
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
N
MB
NA
NB
C
Quick specifics
CYLINDERS 1
MAX POWER kW (hp)@rpm
2.7 (3.7 ) @ 3000
MAX TORQUE Nm@rpm
9.8 @ 2000
KD225S
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
Dimensions (mm)
Sound pressure level up to 2 dB(A)less than the standard version
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
358177 181
417
130
95 115
47.5 7439
R5. 512.5 5
265
Ø11 N°2 holes
358177 181
130
95 115
47.5 7439
R5. 512.5 5
265
Ø11 N°2 holes
95 115
47.5 7439
R5. 512.5 5
265
Ø11 N°2 holes
1400 1600 1800 2000 2200 2400 2600 2800 3000 3200
kW HP
210
230
250
270
290
5.0
6.0
7.0
8.0
9.0
10.0
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
1.3
1.7
2.1
2.5
2.9
3.3
3.7
0.5
0.6
0.7
0.8
0.9
1.0
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
N
MB
NA
NB
C
Quick specifics
CYLINDERS 1 1 1
MAX POWER kW (hp)@rpm
5.1 (6.8) @ 3600 5.0 (6.7) @ 3600 5.3 (7.1) @ 3600
MAX TORQUE Nm@rpm
15.3 @ 2400 14.6 @ 2500 16.0 @ 2500
EMISSIONCOMPLIANCE
- US TIER 4 Final EU STAgE V *
KD350
*available starting from 2019
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
189197.5
445.
5
197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
120120260
189197.5
445.
5
197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
386.5 300.9
Ø11 N°2 holes
189197.5 197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
120120260
189197.5 197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
386.5 300.9
Ø11 N°2 holes
197.8103.1
294.897 30.3
190.255
469.
3
120120260
197.8103.1
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
300.9
Ø11 N°2 holes
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
210
230
250
270
290
12.0
13.0
14.0
15.0
16.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2.0
3.0
4.0
5.0
6.0
7.0
8.01.2
1.3
1.4
1.5
1.6
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
N
MB
NA
NB
C
Quick specifics
CYLINDERS 1
MAX POWER kW (hp)@rpm
5.0 (6.8) @ 3600
MAX TORQUE Nm@rpm
14.7 @ 2200
KD350S
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
189197.5
445.
5
197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
120120260
189197.5
445.
5
197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
386.5 300.9
Ø11 N°2 holes
189197.5 197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
120120260
189197.5 197.8103.1
56.7
133.
5
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
386.5 300.9
Ø11 N°2 holes
197.8103.1
294.897 30.3
190.255
469.
3
120120260
197.8103.1
294.897 30.3
190.255
469.
3
12012026054 90 8 (R5.5)
300.9
Ø11 N°2 holes
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
210
230
250
270
290
10.0
11.0
12.0
13.0
14.0
15.0
1.6
2.0
2.4
2.8
3.2
3.6
4.0
4.4
4.8
5.2
2.0
2.4
2.8
3.2
3.6
4.0
4.4
4.8
5.2
5.6
6.0
6.4
6.8
1.0
1.1
1.2
1.3
1.4
1.5
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
NMB
NA
NB
C
Sound pressure level up to 2 dB(A)less than the standard version
Quick specifics
CYLINDERS 1 1 1
MAX POWER kW (hp)@rpm
7.5 (10.1) @ 3600 7.0 (9.4) @ 3600 7.5 (10.1) @ 3600
MAX TORQUE Nm@rpm
23 @ 2200 23 @ 2200 24.5 @ 2200
EMISSIONCOMPLIANCE
- US TIER 4 Final EU STAgE V *
KD15440
*available starting from 2019
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
412.8403.8
196.4
195.6 165
338.
1
340113.5 57.5
493.
1
512
331.
715
5
99 20554 96
14 45 8R5.5 R5.5
58
Ø11 N°2 holes
412.8403.8
196.4
195.6 165
338.
1
340113.5 57.5
493.
1
512
331.
715
5
99 20554 96
14 45 8R5.5 R5.5
58
Ø11 N°2 holes
340113.5 57.5
512
99 20554 96
14 45 8R5.5 R5.5Ø11 N°2 holes
1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
210
230
250
270
290
19
20
21
22
23
3
4
5
6
7
8
4
5
6
7
8
9
10
11
1.9
2.0
2.1
2.2
2.3
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
NMB
NA
NB
C
Quick specifics
CYLINDERS 1
MAX POWER kW (hp)@rpm
7.3 (10) @ 3600
MAX TORQUE Nm@rpm
22.5 @ 2100
KD15440S
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
Sound pressure level up to 2 Dbless than the standard version
412.8403.8
196.458
195.6 165
256.
3
340352
132 57.531113.5
512
493.
1
331.
715
5
49
8.4
8
xY
A
A5
R5.5 R5.5
2209954
14 4596
4
Ø11 n°2 holes
412.8403.8
196.458
195.6 165
340352
132 57.531113.5
512
493.
1
331.
715
5
49
8.4
8
xY
A
A5
R5.5 R5.5
2209954
14 4596
4
Ø11 n°2 holes
340352
132 57.531113.5
493.
1
49
8.4
8
xY
A
A5
R5.5 R5.5
2209954
14 4596
4
Ø11 n°2 holes
1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
210
230
250
270
290
18
19
20
21
22
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
3
4
5
6
7
8
9
101.8
1.9
2.0
2.1
2.2
160
180
200
220
r.p.m.
kgm Nm
g/HPh g/kWh
N
MB
NA
NB
C
Dimensions (mm)
DATA
Power ratings refer to engines equipped with air filter, standard muffler, after running-in period at ambient conditions of +25°C, relative humidity 30% and 1 bar.Power levels drop by 1% every 100 m altitude and by 2% every 5°C above +25°C.
N - Power curve - 80/1269/CE E-ISO 1585
NB - Power curve - ISO 3046/1 - IFN
NA - Power curve - ISO 3046/1 - ICXN
MB - Torque curve - (NB curve)
C - Specific fuel consumption - (NB curve)
PERFORMANCE CURVES(IFN-ACCORDING TO ISO 3046 and ISO 14396)
26
414 35517210
34128205.5 208.5
504
359
145
212
11
1909
11119 119
R 5,5
57 435R 5.5R 5.5
190
71
26
414 35517210
34128205.5 208.5
212
11
1909
11119 119
R 5,5
57 435R 5.5R 5.5
190
71
26
35517210
34128
212
11
1909
11119 119
R 5,5
57 435R 5.5R 5.5
190
71
1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800
kW HP
230
250
270
290
20.0
22.0
24.0
26.0
28.0
30.0
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
2.0
2.2
2.4
2.6
2.8
3.0
175
195
215
r.p.m.
kgm Nm
g/HPh g/kWh
NMB
NA
NB
C
Setting @ 3000 rpm
Power max. N* (kW) Torque max. (Nm)
8.2 @ 3000 rpm 30 @ 2200 rpm
APPLICATIONS SPECS
KD 225-225S
KD 350-350S
KD15 440
KD 500
Max intermittent axial load in both directions A - B = 200 kg
Minimum pulley diameters for belt drive
Max intermittent axial load in both directions A - B = 200 kg
Minimum pulley diameters for belt drive
Max radial force on pulley for belt drive
Max intermittent axial load in both directions A - B = 150 kg
Minimum pulley diameters for belt drive
Max radial force on pulley for belt drive
Max radial force on pulley for belt drive
F1 (N) ≤70000
55+L1 (mm)
N (kW)
n ( rpm )D1 (mm) ≥ 820 [55 + L1(mm)]
F1 (N) ≤100520
55+L1 (mm)
N (kW)
n ( rpm )D1 (mm) ≥ 570 [55 + L1(mm)]
F1 (N) ≤70000
55+L1 (mm)
D1 (mm) ≥ 820 [55 + L1(mm)]N (kW)
n ( rpm )D2 (mm ) ≥ 740 [90 + L2(mm ) ]
N (kW)
n ( rpm )
F2 (N) ≤77000
90+L2 (mm)
F2 (N) ≤67000
60+L2 (mm)
N (kW)
n ( rpm )D2 (mm) ≥ 900 [48 + L2(mm)]
F2 (N) ≤64000
48+L2 (mm)
N (kW)
n ( rpm )D2 (mm) ≥ 860 [60 + L2(mm)]
Max intermittent axial load in both directions A - B = 2000 N Max
Max radial force on pulley for belt drive
F2 (N) ≤92000
66+L2 (mm)F1 (N) ≤
89000
53+L1 (mm)
D2 (mm) ≥ 620 [66 + L2(mm)]N (kW)
n (rpm)D1 (mm) ≥ 650 [53 + L1(mm)]
N (kW)
n (rpm)
Minimum pulley diameters for belt drive
*Other flanges available on request
AVAILABLE FLANGES*
Ø135
Ø105 -0.036 -0.07
EXT a4 J609a
90.5 71.85/
16-2
4UN
F-2B
-RH
Ø17
.45
25
5
4
30° 30°
45° 45°
Ø165
93 110.14
33.7
Ø22
.1+0
.03
93 92.24
60
24.7
20
28.1
2
3/8”
24U
NF-
28TA
PEXT.4 SAE
KD
225
-225
SK
D 3
50-3
50S
60° 60°
60° 60°
18.7
25
48
25
Ø13
5Ø
105
5
M8X
1.25
-6H
M8X
1.25
-6H
Ø8.
4Ø
23±0
.01
45° 45°
Ø92.07 Ø41.25±0.025
Ø19
.17±
0.25
60 .5±0.5
Ø19
.84±
0.02
20 .5
34.7
Ø28
- 0.
33
Ø41
.25+
0.2
5 H
7
EXT 3 SAE J609a
90.5 61.7
5/16
-24U
NF-
2B-T
AP
4
Ø19.05-0.06
3.3658.34
50.825
21.0
6
Ø41
.25+
0.2
5 H
7
4
4 .76-0.01
EXT 6 SAE
Ø146.07
5/16
-24U
NF-
2B-R
H
46 .8 29.6
25
Ø28
-0.3
3
72 .2
Ø28
-0.3
3
6 .32+0.01
25.4-0.03
EXT a4 J609a
Flange standard - KD 225-225S / KD 350-350S Industrial version
Flange type B - KD 350-350S genset version Industrial version
Flange type A - KD 225-225S genset version Industrial version
Sta
ndar
d v
ersi
on
- K
D 2
25-2
25S
/ K
D 3
50-3
50S
Flange SAE J609a
Flange SAE J609a
5°21’20” equivalent to a2”1/4 per feet
Mounting surface
Mounting surface
Taper 1:5 (5°43’)
4 holes 5/16-24UNF-2B 21 deep
Cylin
der
axis
Mounting surface
4 holes 3/8”-16UNC-2B 17 deep
Mounting surface Mounting surface
Cylin
der
axis
5°21’20” equivalent to a2”1/4 per feet
Cylin
der
axis
Cylin
der
axis
6 holes M8X1.25-6H 20 deep
30° 30°
Ø152I=135
102 43 102 3117
23
M8
Ø 1
05 f8
Ø 2
4
4
174
282
12
(-0.03
6-0
.09) (-0
,036
-0,09
)
30°
45° 45°
I=165.1±0.1
30°
KD
500
KD
500
Ø 1
05 f
8
M16
x1.5
Ø 2
4
98
154
75.5
28.83
25
5/6’
’ 24
UN
F
Ø 2
2.15
+0.0
11-0
.014
Ø 1
46+0
.02
+0.0
7
5° 21’ 20’’
Ø 2
5.4
0 -0.0
25
EXT 6 SAE109.53
0+1.58
Ø 2
6 ±0
,1
86 .42
45°
45°
22.3
Ø 92.1
5 /16’’
102 64.4
61
50.5
28
Ø 2
5.4
0 -0.0
25
3/8’
’ 24
UN
F
6 ,5
21.8
0 -0.1
6.35+0.01-0.03
Ø 41.24 0+0.025
KD
500
Flange standard type - KD 500 Standard version genset version
Flange type B - KD 500 genset version
N° 12 holes M8N°12 holes M8
N° 4 holes M10
Mot
or a
xis
Mot
or a
xis
Taper 1:5 Taper 1:5M
otor
axi
s
PTO on camshaft
5/16’’ 24 UNF depth 7
5/16’’ 24 UNF depth 11
24 UNF depth 17
Mot
or a
xis
*Other flanges available on request
AVAILABLE FLANGES*
KD
440
*Other flanges available on request
AVAILABLE FLANGES*Flange standard type Standard version Industrial version
Flange 2° type genset version
6 holes M8X1.25-6H 20 deep
4 holes 3/8”-16UNC-2B 17 deep
60°
60°
60°
60°
30° 30°
45° 45°
Ø165
Ø135
18.7
25
48
25
Ø13
5Ø
105
Mounting surface
5
M8X
1.25
-6H
M8X
1.25
-6H
Ø8.
4Ø
23±0
.01
Taper1:5 (5°43’)
Mounting surface 20 72.24
4
6024.9
5
95 92.2
Cylin
der
axis
146.
710
5 Ø28
3/8”
24U
NF-
28TA
P
Ø25.4
6.32±0.01
28.1
2
SAE J609a EXT.4
4 holes M8X1.25-6H 20 deep
4 holes 3/8”-16UNC-2B 17 deep
30° 30°
Ø165
Ø127
SAE J609a EXT.6-Ø1inch f lange type B
Cylin
der
axis
95 110.1
33.7 46.8 29.6
5°21’20” equivalent to 2”1/4 per feet
5/16
-24U
NF-
2B-R
H
Ø25
.4
Ø22
.1
25
5Ø28
146.
07
4
Mounting surface SAE J609a typeB
TECHNICAL SPECIFICATIONS
* With restrictions ** According to operating conditions # Available starting from 2019
Model KD 225 KD 225S KD 350 KD 350S
Engine specs
4 stroke air cooled diesel engine • • • •
Conical power take-off on crankshaft • • • •
Anticlockwise rotation • • • •
Forced lubrication with oil pump • • • •
Centrifugal mass governor • • • •
Built-in full flow oil filter • • • •
Oil breathing blow-by with safety device • • • •
Automatic extra fuel starting device • • • •
Self bleeding fuel system • • • •
Torque adjuster • • • •
Automatic compression release • • • •
Die-cast aluminum crankcase with integral cast iron cylinder liner • • • •
Re-borable independent cast iron cylinders - - - -
Aluminum cylinder head • • • •
Built-in rigid feet • • • •
Hydraulic tappets - - - -
Technical features
Cylinder 1 1 1 1
Bore (mm) 69 69 82 82
Stroke (mm) 60 60 66 66
Engine displ (cm3) 224 224 349 349
Injection system DI DI DI DI
Compression ratio 21:1 21:1 20.3:1 20.3:1
Performance
Emission compliance ECE R 24 - ECE R 24US
TIER 4 FEU
STAgE V#-
Rating (kW/HP)N (80/1269/CEE)ISO 1585NB ISO 3046 IFNNA ISO 3046 ICXN
(3600 rpm) 3.5 /4.8 3.3/4.5 3.1/4.2
(3000 rpm)
2.7 /3.7 2.5 /3.4 2.3 /3.1
(3600 rpm) 5.5 /7.4 5.1 /6.8 4.7/6.2
(3600 rpm) -
5.0/6.7 -
(3600 rpm) -
5.3/7.1 -
(3600 rpm) 5.0 /6.8 4.6 /6.2 4.1 /5.6
Max torque (Nm@rpm) 10.4@2400 9.8@2000 15.3@2400 14.6@2500 16.0 @2500 14.7@2200
Min idling speed 950 ÷1000 950 ÷1000 950 ÷1000 950 ÷1000
Fuel compatibility
EN 590 • • • •
No 1 Diesel (US) - ASTM D 975-09 B - grade 1-D S 15 • • • •
No 1 Diesel (US) - ASTM D 975-09 B - grade 1-D S 500 • • • •
No 2 Diesel (US) - ASTM D 975-09 B - grade 2-D S 15 • • • •
No 2 Diesel (US) - ASTM D 975-09 B - grade 2-D S 500 • • • •
ARCTIC EN 590/ASTM D 975-09 B • • • •
High Sulfur Fuel < 5000 ppm (< 0.5%) • • • •
High Sulfur Fuel > 5000 ppm ( > 0.5%) • • • •
Military NATO Fuels F34 - F35 - F44 - F63 - F64 - F65 * • • • •
Military US Fuels JP5 - JP8 (AVTUR) * • • • •
Civil Jet Fuels Jet A/ A1* • • • •
Service features
Fuel tank capacity (l) 3 3 4.3 4.3
Oil sump capacity (l) 0.9 0.9 1.2 1.2
Oil consumption (kg/h) 0.0021 0.0021 0.0032 0.0032
Oil change interval std/synthetic (hr) 250** 250** 250** 250**
Oil filter change interval std/synthetic (hr) 500 500 500 500
Dry air cleaner change interval (hr) 250 250 250 250
Valve adjustement 500 500 500 500
Physical characteristics
H × L × W (fan excluded) (mm)417 × 358 × 265
417× 358× 275
445.5×386.5 ×300.9 446× 387 × 311
Dry weight (kg) 28 28 33 33
Daily service points - positions 1 side service 1 side service 1 side service 1 side service
Ambient operating temps (°C) -10 to +50 -10 to +50 -10 to +50 -10 to +50
gradeability-all round (intermittent -30 min) (deg) 25° 25° 25° 25°
gradeability-all round (peak value -1 min) (deg) 35° 35° 35° 35°
Cap. of air required for correct combustion @3600 (l/min) 350 290 540 540
Cap. of air required for correct cooling @3600 (l/min) 3800 3200 5000 5000
Lubrication Oil typeSAE 5W 40 API SER-VICE CF
SAE 5W 40 API SER-VICE CF
SAE 5W 40 API SERVICE CF
SAE 5W 40 API SER-VICE CF
Model KD15 440 KD15 440S KD 500
Engine specs
4 stroke air cooled diesel engine • • •
Conical power take-off on crankshaft • • •
Anticlockwise rotation • • •
Forced lubrication with oil pump • • •
Centrifugal mass governor • • •
Built-in full flow oil filter • • •
Oil breathing blow-by with safety device • • •
Automatic extra fuel starting device • • •
Self bleeding fuel system • • •
Torque regulator • • •
Automatic compression release • • •
Die-cast aluminum crankcase with integral cast iron cylinder liner
• • -
Re-borable independent cast iron cylinders - - •
Aluminum alloy cylinder head • • •
Built-in rigid feet • • •
Hydraulic tappets • • -
Technical features
Cylinder 1 1 1
Bore (mm) 86 86 87
Stroke (mm) 76 76 85
Engine displ (cm3) 441 441 505
Injection system DI DI DI
Compression ratio 20.3:1 20.5:1 19:1
Performance
Emission compliance ECE R 24 US
TIER 4 FEU
STAgE V#-
ECE R 24
-
Rating (kW/HP)N (80/1269/CEE)ISO 1585NB ISO 3046 IFNNA ISO 3046 ICXN
(3600 rpm) -
7.5 /10.1 -
(3600 rpm) -
7.0 / 9.4 -
(3600 rpm) -
7.5 /10.1 -
7.3 /10.0 6.8 /9.2 6.2 /8.4
(3000 rpm)8.2 /11.1 7.5 /10.2 7.1 /9.6
(3600 rpm)8.8 /12
8.2 /11.1 7.5 /10.2
Max torque (Nm@rpm) 23 @2200 23@2200 24.5@2200 22.5@2100 30.0@2200
Min idling speed 950 ÷1000 1150 1200
Fuel compatibility
EN 590 • • •
No 1 Diesel (US) - ASTM D 975-09 B - grade 1-D S 15 • • •
No 1 Diesel (US) - ASTM D 975-09 B - grade 1-D S 500 • • •
No 2 Diesel (US) - ASTM D 975-09 B - grade 2-D S 15 • • •
No 2 Diesel (US) - ASTM D 975-09 B - grade 2-D S 500 • • •
ARCTIC EN 590/ASTM D 975-09 B • • •
High Sulfur Fuel < 5000 ppm (< 0.5%) • • •
High Sulfur Fuel > 5000 ppm ( > 0.5%) • • •
Military NATO Fuels F34 - F35 - F44 - F63 - F64 - F65 * • • •
Military US Fuels JP5 - JP8 (AVTUR) * • • •
Civil Jet Fuels Jet A/ A1* • • •
Service features
Fuel tank capacity (l) 4.3 4.3 5
Oil sump capacity (l) 1.2 1.2 1.5
Oil consumption (kg/h) 0.0032 0.0032 0.0055
Oil/filter change interval std/synthetic (hr) 250** 250** 250**
Oil filter change interval std/synthetic (hr) 500 500 500
Dry air cleaner change interval (hr) 500 500 250
Valve adjustement 500 500 500
Physical characteristics
H × L × W (fan excluded) (mm) 493.1 × 412.8 ×340 493.1 × 412.8 ×352 504x415x355
Dry weight (kg) 45 45 48
Daily service points - positions 1 side service 1 side service 1 side service
Ambient operating temps (°C) -10 to +50 -10 to +50 -10 to +50
gradeability-all round (intermittent -30 min) (deg) 25 25 25°
gradeability-all round (peak value -1 min) (deg) 35 35 35°
Cap. of air required for correct combustion@3600 (l/min)
640 640 800
Cap. of air required for correct cooling @3600 (l/min) 5500 5500 8700
Lubrication Oil typeSAE 5W 40 API
SERVICE CFSAE 5W 40 API
SERVICE CFSAE 5W 40 API
SERVICE CF
TECHNICAL SPECIFICATIONS
* With restrictions ** According to operating conditions # Available starting from 2019
DEUTSCHLANDLombardini Motoren gmbHFritz-Klatte-Str. 6, Bürogebäude 265933 Frankfurt am Main, DEUTSCHLANDT. +49-(0)[email protected]
EUROPELombardini SrlVia Cav. del lavoro A. Lombardini n° 2 42124 Reggio Emilia, ITALYT. +39-(0)522-389-1 [email protected]
FRANCELombardini France S.a.s.47 Allée de Riottier,69400 Limas, FRANCET. +33-(0)[email protected]
ROAPACKohler Singapore Pte Ltd(Kohler Power Systems)7 Jurong Pier RoadSINGAPORE 619159T. [email protected]
UKLombardini U.K. Ltd1, Rochester Barn - Eynsham RoadOX2 9NHOxford, UKT. +44-(0)[email protected]
ESPAÑALombardini ESPAÑA, S.L.P.I. Cova Solera 1-908191 - Rubí (Barcelona)ESPAÑAT. +34-(0)[email protected]
Lombardini s.r.l. is a company of Kohler Group and has manufacturing facilities in Italy, Slovakia and India and sales subsidiaries in France,Germany, UK, Spain and Singapore.
Kohler reserves the right to make modifications without prior notice.For the latest version please visit our website:
KOHLERENGINES.COM/EU Printed in Italy ED0035584830 Rev.07 09/17 KOHLER CO.