alcohol washing - bee awarealcohol washing background alcohol washing is a quick and effectively...
TRANSCRIPT
Alcohol washing BACKGROUND Alcohol washing is a quick and effectively method for detecting the presence of Varroa mites, as well as monitoring colony mite levels. The disadvantage of this method is that it kills the bees that are sampled. The alcohol wash method can remove 70-80% of external Varroa mites present on adult honey bees. The method can also be used for Tropilaelaps mites and Braula fly surveillance, however, with less confidence because these pests are not present in large numbers of worker bees.
It is recommended that all beekeepers conduct this monitoring technique as it is rapid and simple. Very little equipment is required and it can be easily performed during routine hive inspections. This technique is more effective when little brood is present, however it will provide measurable results when there is also significant quantities of brood and the sample bees are taken from the centre of the brood nest.
Equipment required • 2 plastic jars, about 500 grams in size and
with wide mouth
• 3mm gauze wire mesh
• Soldering gun
• Cup (about 250 mL)
• 100 mL of 25% rubbing alcohol or 25%
methylated spirits
• Newspaper or large plastic sheet
• Protective clothing, smoker and hive tool
• Magnifying lens (if available)
• A container (e.g. small white bucket)
• Filter paper (e.g. cloth, coffee filter)
How to make an alcohol washing kit
• Acquire two identical plastic jars (such as
large peanut butter jars) with screw top lids.
• Carefully remove (by safely cutting) the inner
section of the closed-end of the screw-top
lids to acquire the desired effect.
• Cut out a 3mm gauze wire mesh and place
between the two open screw-top lids.
A plastic lid with the inner removed and covered with a section of 1/8” wire mesh. Image courtesy Randy Oliver, www.scientificbeekeeping.com.
• Plastic jar lids are commonly made from
polypropylene and cannot be glued
effectively. Therefore, you will need to heat
weld them together. A soldering gun is best
suited to this purpose. A deep weld is
required as a light weld may crack with use.
A soldering gun joining the two plastic lids together, with both inner lids removed and the 1/8” wire mesh sandwiched between the lids. Image courtesy Randy Oliver, www.scientificbeekeeping.com.
• Connect both of the jars to the lids and make
sure that the lid connection is strong.
• You now have a functional mite shaker for
conducting the alcohol washing test.
A functional mite washing kit, including a white bucket, mite shaker, bottle of 25% alcohol, a measuring cup and a sieve. Image courtesy Randy Oliver, www.scientificbeekeeping.com.
Procedure #1
• Place about 100 mL of alcohol in one of the
jars, or enough so that the bees will be
covered.
• Place a large sheet of newspaper or plastic
beside the hive to be tested.
• Light a smoker, open the hive and remove a
frame which contains a lot of brood. If the
queen is present place her back in the hive.
• Shake bees from a brood frame onto the
newspaper/plastic sheet/plastic tub.
• The field bees will mostly fly out of the tub
immediately, leaving behind predominantly
nurse bees which are likely to carry a greater
quantity of phoretic Varroa mites.
Shake a brood comb into a container. Image courtesy Daniel Martin, VIC DEPI.
• Pour about 300 bees (1/2 a cup) into the jar
containing around 100ml of 25% rubbing
alcohol or methylated spirits.
Pouring bees into the mite shaker. Image courtesy Daniel Martin, VIC DEPI.
• Put the solid lid on the jar quickly to prevent
the bees from escaping.
Screw the two mite shakers together firmly. Image courtesy Daniel Martin, VIC DEPI.
• Invert the shaker so that the bees are now in
the top jar.
• Shake the jar vigorously for 20 seconds,
ensuring the honey bees are covered in
alcohol. It is essential to maintain a vigorous
shaking motion in order for the alcohol to
swirl with the bees in the top jar.
Shake the mite shaker jars vigorously for around 20 seconds. Image courtesy Daniel Martin, VIC DEPI.
• After 20 seconds and the last shake, jiggle
the jar so that the alcohol drains through the
bees into the bottom jar. If you don’t jiggle,
some of the mites may get stuck on the bees
in the top jar.
• Once settled, raise the bottom of the jar to
view any mites that have been dislodged
from the bees.
A large number of Varroa mites present. The blue arrows indicate some at the bottom of the mite shaker after settling. Image courtesy Daniel Martin, VIC DEPI.
Procedure #2
• This method does not require a soldering gun
to join plastic jars together.
• Get a plastic jar with an intact covered lid.
• Follow the first 6 steps as outlined in
Procedure #1.
• Shake the bees in the jar with the alcohol for
20 seconds.
• Place a piece of cloth over the top of a small
bucket or container, with the 3mm gauze
wire mesh slightly over the cloth.
• Pour the contents of the jar through the
mesh and over the cloth. The mesh lid will
collect the bees but enable any mites to pass
through and be collected on the cloth.
• Inspect the surface of the cloth thoroughly
for mites. A magnifying lens can be used if
available.
• Higher recovery rates of Varroa mite can be
achieved by refilling the jar containing bees
with water and rinsing the bees once or
twice. Two rinses will recover more than 95%
of Varroa mites present on the bees.
• This method does not require a soldering gun
to join jars together.
Reporting
• If Varroa mites, Tropilaelaps mites or Braula
fly are suspected, report the finding
immediately to the relevant state/territory
agriculture agency through the Exotic Plant
Pest Hotline (1800 084 881) or by directly
reporting to the state/territory Chief Plant
Health Manager.