all metals and long-distance types e2v · copper x t= 3 mm sensing distance x (mm) stainless steel...
TRANSCRIPT
CSM_E2V_DS_E_2_1
1
All Metals and Long-distance Types
E2V
Aluminum and Iron Both Detectable from Long Distances
1.5 to 2 times the aluminum detection distance of previous models
Twice the max. distance
Long-distance Long-distance aluminum detectionaluminum detection
Long-distance aluminum detection
Equipped with a function to prevent the detection of aluminum chips
Aluminum chip Aluminum chip protectionprotection
Aluminum chip protection
Refer to Safety Precautions on page 8.For the most recent information on models that have been certified for safety standards, refer to your OMRON website.
FeaturesAluminum Detection Distance: 1.5 to 2 Times Previous Models *Immunity against aluminum chips has enabled achieving long-distance detection of aluminum workpieces. The same detection distance has also been achieved for iron, allowing the E2V-X@ to be separated from workpieces made of either metal farther than any other Proximity Sensor.
* In-house comparison of M18 Shielded Long-distance Models
Detection Made VisibleAn operation indicator that is visible from any direction is provided as a standard feature.This indicator flashes under unstable conditions for easy installation condition verification at a glance.
Embeddable in Metal.The first Long-distance Sensor that is shielded. Possible to be completely embedded in metal.
0 1 2 3 4 5 6 7 8 9
Excellent Performance, with Aluminum Chip Immunity!
0 1 2 3 4 5 6 7 8 9
Sensing distance (mm)
E2E
E2EM
E2EZ
E2EV
E2V
Aluminum Also Detects Iron at Long Distances!Iron
×1.5
E2EStandard Model
E2EMLong-distance (Ferrous Metals)
E2EZAluminum Chip Immunity
E2EVAll Metals
E2V
Sensing distance (mm)
Previous Sensor
Visible
The indicator may be difficult
to see from some
directions.
The indicator is visible from any direction.
The indicator is visible from any direction.
E2V Pre-wired Modelsand Pre-wired Connector Models
E2V Connector Models
180° 180° 180°
Embedded Mounting in Metal
E2EM E2V
Wor
kpie
ce
Pro
trud
ing
dist
ance
Bra
cket
Wor
kpie
ce
E2V
2
Ordering InformationSensors (Dimensions ➜ page 9)
Standard-distance typeDC 3-wire, Pre-wired Models (Standard Cable Length: 2 m)
Long-distance typeDC 3-wire, Pre-wired Models (Standard Cable Length: 2 m)
Long-distance typeDC 3-wire, Connector Models
Long-distance typeDC 3-wire, Smartclick Pre-wired Connector (M12) Models
Appearance Sensing distance OutputModel
Operation mode NO Operation mode NC
M12PNP E2V-X2B1 2M E2V-X2B2 2MNPN E2V-X2C1 2M E2V-X2C2 2M
M18PNP E2V-X5B1 2M E2V-X5B2 2MNPN E2V-X5C1 2M E2V-X5C2 2M
M30PNP E2V-X10B1 2M E2V-X10B2 2MNPN E2V-X10C1 2M E2V-X10C2 2M
Appearance Sensing distance OutputModel
Operation mode NO Operation mode NC
M12PNP E2V-X4B1 2M E2V-X4B2 2MNPN E2V-X4C1 2M E2V-X4C2 2M
M18PNP E2V-X8B1 2M E2V-X8B2 2MNPN E2V-X8C1 2M E2V-X8C2 2M
M30PNP E2V-X15B1 2M E2V-X15B2 2MNPN E2V-X15C1 2M E2V-X15C2 2M
Appearance Sensing distance OutputModel
Operation mode NO Operation mode NC
M12PNP E2V-X4B1-M1 E2V-X4B2-M1NPN E2V-X4C1-M1 E2V-X4C2-M1
M18PNP E2V-X8B1-M1 E2V-X8B2-M1NPN E2V-X8C1-M1 E2V-X8C2-M1
M30PNP E2V-X15B1-M1 E2V-X15B2-M1NPN E2V-X15C1-M1 E2V-X15C2-M1
Appearance Sensing distance OutputModel
Operation mode NO
M12PNP E2V-X4B1-M1TJ 0.3MNPN E2V-X4C1-M1TJ 0.3M
M18PNP E2V-X8B1-M1TJ 0.3MNPN E2V-X8C1-M1TJ 0.3M
M30PNP E2V-X15B1-M1TJ 0.3MNPN E2V-X15C1-M1TJ 0.3M
Shielded
2 mm
5 mm
10 mm
Shielded
4 mm
8 mm
15 mm
Shielded
4 mm
8 mm
15 mm15 mm
Shielded
4 mm
8 mm
15 mm15 mm15 mm
E2V
3
Accessories (Order Separately)Sensor I/O Connectors (M12, Sockets on One Cable End) (Required for models with Pre-wired Connectors.) A Connector is not provided with the Sensor. Be sure to order a Connector separately.(Dimensions ➜ XS5)
Sensor I/O Connectors (M12, Sockets on One Cable End) Standard type (Required for models for Connectors.) A Connector is not provided with the Sensor. Be sure to order a Connector separately.(Dimensions ➜ XS2)
Appearance Type Cable length Model Applicable Proximity Sensor Models
Standard cable2 m XS5F-D421-D80-F
E2V-X@B1-M1TJE2V-X@C1-M1TJ
5 m XS5F-D421-G80-F
Oil-resistant polyurethane cable
2 m XS5F-D421-D80-P
5 m XS5F-D421-G80-P
Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor Models
2 m XS2F-D421-DC0-F E2V-X@C1-M1E2V-X@B1-M15 m XS2F-D421-GC0-F
2 m XS2F-D421-D80-F E2V-X@C@-M1E2V-X@B@-M15 m XS2F-D421-G80-F
2 m XS2F-D422-DC0-F E2V-X@C1-M1E2V-X@B1-M15 m XS2F-D422-GC0-F
2 m XS2F-D422-D80-F E2V-X@C@-M1E2V-X@B@-M15 m XS2F-D422-G80-F
Smartclick Connector, Straight
Straight
L-shape
E2V
4
Ratings and Specifications
* The response frequency is an average value.Measurement conditions are as follows: Standard sensing object, a distance between target objects of twice the size of the standard sensing object, and a set distance of half the sensing distance.
Size M12 M18 M30
Item Model E2V-X2@@ E2V-X4@@ E2V-X5@@ E2V-X8@@ E2V-X10@@ E2V-X15@@
Sensing distance 2 mm±10% 4 mm±10% 5 mm±10% 8 mm±10% 10 mm±10% 15 mm±10%
Set distance 0 to 1.6 mm 0 to 3.2 mm 0 to 4.0 mm 0 to 6.4 mm 0 to 8.0 mm 0 to 12.0 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metals and non-ferrous metals (The sensing distance depends on the material of the sensing object. Refer to Engineering Data (Reference value).)
Standard sensing object
Aluminum: 12 × 12 × 3 mm
Aluminum: 12 × 12 × 3 mm
Aluminum: 18 × 18 × 3 mm
Aluminum: 24 × 24 × 3 mm
Aluminum: 30 × 30 × 3 mm
Aluminum: 45 × 45 × 3 mm
Response frequency * 150 Hz 40 Hz 70 Hz 40 Hz 70 Hz 30 Hz
Power supply voltage (operating voltage range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Current consumption 450 mW max. (Current consumption: 15 mA max. at power supply voltage of 30 V)
Co
ntr
ol
ou
tpu
t Load current Open-collector output, 100 mA max.
Residual voltage 2 V max. (Load current: 100 mA, Cable length: 2 m)
Indicators NO Models: Operation indicator (yellow) (flashing), Setting indicator (yellow) (lit); NC Models: Operation indicator (yellow) (lit)
Operation modeB1/C1 Models: NO
(Refer to the timing charts under I/O Circuit Diagrams for details.) B2/C2 Models: NC
Protection circuits Power supply reverse polarity protection, reversed output polarity protection, load short-circuit protection, surge suppressor
Ambient temperature Operating/Storage: -25 to 70°C (with no icing or condensation)
Ambient humidity Operating/Storage: 35% to 95% (with no condensation)
Temperature influence
Based on the sensing distance at 23°C in the temperature range of -25 to 70°C
±10% max. ±15% max. ±10% max. ±15% max. ±10% max. ±15% max.
Voltage influence ±1.5% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection IEC IP67 (Pre-wired Models and Pre-wired Connector Models are oil-resistant to the OMRON in-house standard.)
Connection method
Pre-wired Models (Standard cable length: 2 m), Connector Models, Pre-wired Connector Models (Standard cable length: 300 mm)
Wei
gh
t(p
acke
d
stat
e)
Cable Approx. 120 g Approx. 150 g Approx. 200 g
Connector Approx. 30 g Approx. 45 g Approx. 120 g
Pre-wired Connector Models
Approx. 50 g Approx. 70 g Approx. 140 g
Mat
eria
ls
Case Nickel-plated brass
Sensing surface Heat-resistant ABS
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual
E2V
5
Engineering Data (Reference Value)
Influence of Sensing Object Size and Material
E2V-X2 E2V-X4 E2V-X5
E2V-X8 E2V-X10 E2V-X15
Influence of Sensing Object Size and Material
E2V-X2 E2V-X4 E2V-X5
Side length of sensing object d (mm)
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0 5 10 15 20 25 30
Iron
Brass
Copper
X
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
@d
Aluminum
@d
X
0 5 10 15 20 25 300.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Side length of sensing object d (mm)
Iron
Brass
Aluminum
Copper
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
X
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0 5 10 15 20 25 30 35 40Side length of sensing object d (mm)
Iron
Brass
AluminumCopper
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
@d
X
0.0
2.0
4.0
6.0
8.0
10.0
0 5 10 15 20 25 30 35 40Side length of sensing object d (mm)
Iron
Brass
Aluminum
Copper
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
@d
X
10 20 30 40 50 600.0
2.0
4.0
6.0
8.0
10.0
12.0
0Side length of sensing object d (mm)
Iron
Brass
Aluminum
Copper
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
@d
X
10 20 30 40 50 6000.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
Side length of sensing object d (mm)
Iron
Brass
Aluminum
Copper
t= 3 mm
Stainless steel (SUS304)
Sen
sing
dis
tanc
e X
(m
m)
@d
tX
0 1 2 3 4 5 60.0
0.5
1.0
1.5
2.0
2.5
3.0
Thickness of sensing object: t (mm)
Iron
Brass
Aluminum
Copper
Stainless steel (SUS304)
Sensing object size: 12 × 12 mm
Sen
sing
dis
tanc
e X
(m
m)
tX
0 1 2 3 4 5 60.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Thickness of sensing object: t (mm)
IronBrass
Aluminum
Copper
Stainless steel (SUS304)
Sensing object size: 12 × 12 mm
Sen
sing
dis
tanc
e X
(m
m)
tX
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0 1 2 3 4 5 6 7 8Thickness of sensing object: t (mm)
Iron
Brass
Copper
Stainless steel (SUS304)
Sensing object size: 18 × 18 mm
Sen
sing
dis
tanc
e X
(m
m) Aluminum
E2V
6
E2V-X8 E2V-X10 E2V-X15
Sensing Area
tX
0 1 2 3 4 5 6 7 80.0
2.0
4.0
6.0
8.0
10.0
Thickness of sensing object: t (mm)
Iron
BrassAluminum
Copper
Stainless steel (SUS304)
Sensing object size: 24 × 24 mm
Sen
sing
dis
tanc
e X
(m
m)
tX
0 2 4 6 8 10 120.0
2.0
4.0
6.0
8.0
10.0
12.0
Thickness of sensing object: t (mm)
Iron
Brass
Aluminum
Copper
Stainless steel (SUS304)
Sensing object size: 30 × 30 mm
Sen
sing
dis
tanc
e X
(m
m)
tX
0 2 4 6 8 10 120.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
Thickness of sensing object: t (mm)
Iron
Brass
Stainless steel (SUS304)
Sensing object size: 45 × 45 mm
Sen
sing
dis
tanc
e X
(m
m)
Aluminum
Copper
XY
-12.0 -9.0 -6.0 -3.0 0.0 3.0 6.0 9.0 12.00.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
E2V-X5@
E2V-X10@
E2V-X8@
E2V-X15@
Sensing area (Aluminum) (Thickness: 3.0 mm)Sensing distance Y (mm)
Sen
sing
dis
tanc
e X
(m
m)
E2V-X4@
E2V-X2@
XY
-12.0 -9.0 -6.0 -3.0 0.0 3.0 6.0 9.0 12.00.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
E2V-X15@
Sensing area (Iron) (Thickness: 3.0 mm)Sensing distance Y (mm)
Sen
sing
dis
tanc
e X
(m
m)
E2V-X10@
E2V-X5@
E2V-X8@
E2V-X4@
E2V-X2@
E2V
7
I/O Circuit DiagramsNPN Output
PNP Output
Connections for Sensor I/O Connectors
Model Operation mode Timing charts Output circuit
E2V-X@C@(-M1/-M1TJ)
NO
NC
Model Operation mode Timing charts Output circuit
E2V-X@B@(-M1/-M1TJ)
NO
NC
Proximity SensorSensor I/O Connector
model number ConnectionsType Operation
mode Model
DC 3-wire
NO E2V-X@C1-M1E2V-X@B1-M1
NC E2V-X@C2-M1E2V-X@B2-M1
Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details.
Sensing object
Rated sensing distance
(%) 100 0 80
Flashing
Stable sensing area
Non-sensing area
Unstable sensing area
Set position
Proximity sensor
ON
OFF ON
OFF
Yellow indicator
Control output
Proximity Sensor main circuit
0 V
+V
Load
Note: Connector Models NO Models: NC Models:
Compatible Connector Cables: XS5F SeriesXS2F Series
M1:M1TJ:
Brown
Black
Blue
Sensing object
Rated sensing distance
(%) 100 0
Non-sensing areaProximity sensor
ON
OFF ON
OFF
Sensing area
Yellow indicator
Control output
100 0 80
Sensing object
Rated sensing distance
(%)
Flashing
Stable sensing area
Non-sensing area
Unstable sensing area
Set position
Proximity sensor
ON
OFF ON
OFF
Yellow indicator
Control output
+V
0 V
Proximity Sensor main circuit
Load
Brown
Black
Blue
Note: Connector Models NO Models: NC Models:
Compatible Connector Cables: XS5F SeriesXS2F Series
M1:M1TJ:
100 0
Sensing object
Rated sensing distance
(%)
Non-sensing areaProximity sensor
ON
OFF ON
OFF
Sensing area
Yellow indicator
Control output
XS2F-D42@-@C0-F
1: Straight2: L-shape
D: 2-m cableG: 5-m cable
1
2
3
4
1
2
3
4
E2V
Mai
nC
ircui
t
XS2F
Brown (+V)
Blue (0 V)Black (Output)
XS2F-D42@-@80-F
1: Straight2: L-shape
D: 2-m cableG: 5-m cable
E2V XS2F
1
2
3
4
1
2
3
4
Brown (+V)
Blue (0 V)White (Blank)
Black (Output)
Mai
nC
ircui
t
E2V XS2F
1
2
3
4
1
2
3
4
Brown (+V)
Blue (0 V)Black (Blank)
White (Output)
Mai
nC
ircui
t
E2V
8
Safety PrecautionsRefer to the Proximity Sensors Technical Guide.
This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes.
Never use the product with an AC power supply. Otherwise, explosion may result.
Do not use the product in atmospheres or environments that exceed product ratings.DesigningInfluence of Surrounding MetalWhen embedding the Sensor in metal, be sure that the clearances given in the following table are maintained.
Table 1. Influence of Surrounding Metal (Unit: mm)
* If the thickness of the mounting bracket (t) exceeds 5 mm, be sure to installthe Sensor so that ≥ 2, d (dia.) ≥ 45, and D ≥ 2.
Mutual InterferenceWhen installing Sensors face-to-face or side-by-side, be sure that the minimum distances given in table 2 are maintained.
Chart 2. Mutual Interference (Unit: mm)
Sensing Distance• The sensing distance depends on the sensing object size,
material, and thickness.• If the sensing object has a thickness of less than 1 mm, the sensing
distance will decrease.• In some cases, it may not be possible to detect stainless steel.
Use the following graph and the Influence of Sensing Object Size and Material information in Engineering Data (Reference Value) as a reference.
Aluminum and Iron CuttingsNormally aluminum or iron cuttings will not be detected even if they adhere to or accumulate on the sensing surface. Detection signals may be output for the following. If this occurs, remove the cuttings from the sensing surface.Diameter of cutting = d and diameter of sensing surface = DCuttings in center of sensing surface with d ≥ 2/3D
(Unit: mm)
Tightening TorqueDo not tighten the nut with excessive force.A washer must be used with the nut.
WARNING
Precautions for Correct Use
Item Model E2V-X2 E2V-X5 E2V-X100 0 0
d dia. 12 18 30D 0 0 0m 12 24 45n 18 27 45
Item Model E2V-X4 E2V-X8 E2V-X150 0 0 *
d dia. 12 18 30 *D 0 0 0 *m 12 24 45n 18 27 45
Item Model E2V-X2 E2V-X5 E2V-X10A 30 50 100B 20 30 50
Item Model E2V-X4 E2V-X8 E2V-X15A 35 60 120B 25 35 70
mn
t t tm
Dd dia.
ℓ
ℓ
ℓ
AB
Mode Size DE2V-X2@/X4@ 10E2V-X5@/X8@ 16E2V-X10@/X15@ 28
Tightening Torque Part A Part BModel Dimension (mm) Torque TorqueE2V-X2/X4 17 5.9 N⋅m 9.8 N⋅mE2V-X5/X8 22 15 N⋅m 45 N⋅mE2V-X10/X15 26 39 N⋅m 78 N⋅m
d
D Sensing surface
Cutting
Cutting
Pressed against sensing surface.
Part B Part A
(Shielded Model)
E2V
9
DimensionsSensorsPre-wired Models
Pre-wired Connector Models
(Unit: mm)Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
4M12 × 1
47
6017
21 dia.
Two clamping nutsToothed washer
Indicator *1
6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
E2V-X2/X4
24 42
60
52
4M18 × 1 Two clamping nuts
Toothed washer
Indicator *1
6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
29 dia.
E2V-X5/X8
5
36 42
60
52
M30 × 1.5 Two clamping nutsToothed washer
Indicator *1
6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m
*1 NO Models: Operation indicator (yellow) (flashing) Setting indicator (yellow) (ON) NC Models: Operation indicator (yellow) (ON)
42 dia.
E2V-X10/X15
4
17 47
60
M12 × 1 M12 × 1Two clamping nutsToothed washer
Indicator *1
6-dia. vinyl-insulated round cableStandard length: 300 mm
21 dia.
E2V-X4-M1TJ
4
24 42
60
52
M18 × 1M12 × 1
Two clamping nutsToothed washer
Indicator *1
6-dia. vinyl-insulated round cableStandard length: 300 mm
29 dia.
E2V-X8-M1TJ
5
*1 NO Models: Operation indicator (yellow) (flashing) Setting indicator (yellow) (ON) NC Models: Operation indicator (yellow) (ON)
36 42
60
52
M30 × 1.5
M12 × 1
Two clamping nutsToothed washer
Indicator *1
6-dia. vinyl-insulated round cableStandard length: 300 mm
42 dia.
E2V-X15-M1TJ
E2V
10
Connector Models
Mounting Hole Dimensions
GA
EF
C
B
D
M12 × 1Four indicators *1
Two clamping nutsToothed washer
*1 NO Models: Operation indicator (yellow) (flashing) Setting indicator (yellow) (ON) NC Models: Operation indicator (yellow) (ON)
ModelItem E2V-X4@-M1 E2V-X8@-M1 E2V-X15@-M1
A M12 × 1 M18 × 1 M30 × 1.5B 65 60 63C 47 42 42D 52 47 49E 21 dia. 29 dia. 42 dia.F 17 24 36G 4 4 5
H
Proximity Sensor dimensions M12 M18 M30
Dimension H (mm) 12.5 dia. 18.5 dia. 30.5 dia.+0.50
+0.50
+0.50
Terms and Conditions of Sale1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,catalogs, manuals, brochures and other documents, whether electronic or inwriting, relating to the sale of products or services (collectively, the "Products")by Omron Electronics LLC and its subsidiary companies (“Omron”). Omronobjects to any terms or conditions proposed in Buyer’s purchase order or otherdocuments which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-out notice by Omron. Omron reserves the right to increase or decrease priceson any unshipped portions of outstanding orders. Payments for Products aredue net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoicessent to Buyer after deducting transportation charges, taxes and duties, and willbe allowed only if (i) the invoice is paid according to Omron’s payment termsand (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month orthe maximum legal rate, whichever is less, on any balance not paid within thestated terms.
5. Orders. Omron will accept no order less than $200 net billing. 6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than generalreal property and income taxes), including any interest or penalties thereon,imposed directly or indirectly on Omron or required to be collected directly orindirectly by Omron for the manufacture, production, sale, delivery, importa-tion, consumption or use of the Products sold hereunder (including customsduties and sales, excise, use, turnover and license taxes) shall be charged toand remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactoryto Omron, Omron reserves the right to stop shipments or require satisfactorysecurity or payment in advance. If Buyer fails to make payment or otherwisecomply with these Terms or any related agreement, Omron may (without liabil-ity and in addition to other remedies) cancel any unshipped portion of Prod-ucts sold hereunder and stop any Products in transit until Buyer pays allamounts, including amounts payable hereunder, whether or not then due,which are owing to it by Buyer. Buyer shall in any event remain liable for allunpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellationunless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in deliveryresulting from causes beyond its control, including earthquakes, fires, floods,strikes or other labor disputes, shortage of labor or materials, accidents tomachinery, acts of sabotage, riots, delay in or lack of transportation or therequirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shallpass from Omron to Buyer; provided that Omron shall retain a security inter-est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; ande. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writingto Omron within 30 days of receipt of shipment and include the original trans-portation bill signed by the carrier noting that the carrier received the Productsfrom Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that theProducts will be free from defects in materials and workmanship for a period oftwelve months from the date of sale by Omron (or such other period expressedin writing by Omron). Omron disclaims all other warranties, express or implied.(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THEPRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIRINTENDED USE. Omron further disclaims all warranties and responsibility ofany type for claims or expenses based on infringement by the Products or oth-erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-gation hereunder shall be, at Omron’s election, to (i) replace (in the formoriginally shipped with Buyer responsible for labor charges for removal orreplacement thereof) the non-complying Product, (ii) repair the non-complyingProduct, or (iii) repay or credit Buyer an amount equal to the purchase price ofthe non-complying Product; provided that in no event shall Omron be responsi-ble for warranty, repair, indemnity or any other claims or expenses regardingthe Products unless Omron’s analysis confirms that the Products were prop-erly handled, stored, installed and maintained and not subject to contamina-tion, abuse, misuse or inappropriate modification. Return of any Products byBuyer must be approved in writing by Omron before shipment. Omron Compa-nies shall not be liable for the suitability or unsuitability or the results from theuse of Products in combination with any electrical or electronic components,circuits, system assemblies or any other materials or substances or environ-ments. Any advice, recommendations or information given orally or in writing,are not to be construed as an amendment or addition to the above warranty.See http://www.omron247.com or contact your Omron representative for pub-lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLEFOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANYWAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM ISBASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.Further, in no event shall liability of Omron Companies exceed the individualprice of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies andtheir employees from and against all liabilities, losses, claims, costs andexpenses (including attorney's fees and expenses) related to any claim, inves-tigation, litigation or proceeding (whether or not Omron is a party) which arisesor is alleged to arise from Buyer's acts or omissions under these Terms or inany way with respect to the Products. Without limiting the foregoing, Buyer (atits own expense) shall indemnify and hold harmless Omron and defend or set-tle any action brought against such Companies to the extent based on a claimthat any Product made to Buyer specifications infringed intellectual propertyrights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-sive property of Omron Companies and Buyer shall not attempt to duplicate itin any way without the written permission of Omron. Notwithstanding anycharges to Buyer for engineering or tooling, all engineering and tooling shallremain the exclusive property of Omron. All information and materials suppliedby Omron to Buyer relating to the Products are confidential and proprietary,and Buyer shall limit distribution thereof to its trusted employees and strictlyprevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations andlicenses regarding (i) export of products or information; (iii) sale of products to“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens ofregulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any rightand no course of dealing between Buyer and Omron shall operate as a waiverof rights by Omron. (b) Assignment. Buyer may not assign its rights hereunderwithout Omron's written consent. (c) Law. These Terms are governed by thelaw of the jurisdiction of the home office of the Omron company from whichBuyer is purchasing the Products (without regard to conflict of law princi-ples). (d) Amendment. These Terms constitute the entire agreement betweenBuyer and Omron relating to the Products, and no provision may be changedor waived unless in writing signed by the parties. (e) Severability. If any provi-sion hereof is rendered ineffective or invalid, such provision shall not invalidateany other provision. (f) Setoff. Buyer shall have no right to set off any amountsagainst the amount owing in respect of this invoice. (g) Definitions. As usedherein, “including” means “including without limitation”; and “Omron Compa-nies” (or similar words) mean Omron Corporation and any direct or indirectsubsidiary or affiliate thereof.
Certain Precautions on Specifications and Use1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of theProduct in the Buyer’s application or use of the Product. At Buyer’s request,Omron will provide applicable third party certification documents identifyingratings and limitations of use which apply to the Product. This information byitself is not sufficient for a complete determination of the suitability of the Prod-uct in combination with the end product, machine, system, or other applicationor use. Buyer shall be solely responsible for determining appropriateness ofthe particular Product with respect to Buyer’s application, product or system.Buyer shall take application responsibility in all cases but the following is anon-exhaustive list of applications for which particular attention must be given:(i) Outdoor use, uses involving potential chemical contamination or electricalinterference, or conditions or uses not described in this document.(ii) Use in consumer products or any use in significant quantities. (iii) Energy control systems, combustion systems, railroad systems, aviationsystems, medical equipment, amusement machines, vehicles, safety equip-ment, and installations subject to separate industry or government regulations. (iv) Systems, machines and equipment that could present a risk to life or prop-erty. Please know and observe all prohibitions of use applicable to this Prod-uct. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUSRISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUTENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THEOVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for theuser’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogsand other materials is provided as a guide for the user in determining suitabil-ity and does not constitute a warranty. It may represent the result of Omron’stest conditions, and the user must correlate it to actual application require-ments. Actual performance is subject to the Omron’s Warranty and Limitationsof Liability.
4. Change in Specifications. Product specifications and accessories may bechanged at any time based on improvements and other reasons. It is our prac-tice to change part numbers when published ratings or features are changed,or when significant construction changes are made. However, some specifica-tions of the Product may be changed without any notice. When in doubt, spe-cial part numbers may be assigned to fix or establish key specifications foryour application. Please consult with your Omron’s representative at any timeto confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has beenchecked and is believed to be accurate; however, no responsibility is assumedfor clerical, typographical or proofreading errors or omissions.
OMRON CANADA, INC. • HEAD OFFICEToronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICEMéxico DF • 52.55.59.01.43.00 • 01-800-226-6766 • [email protected]
OMRON ELECTRONICS DE MEXICO • SALES OFFICEApodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • [email protected]
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICESão Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICECono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICESantiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES54.11.4783.5300
Authorized Distributor:
Note: Specifications are subject to change. © 2014 Omron Electronics LLC Printed in U.S.A.
Printed on recycled paper.
Automation Control Systems• Machine Automation Controllers (MAC) • Programmable Controllers (PLC) • Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls • Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers • Single and Multi-loop Controllers
Sensors & Vision• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors• Amplified Photomicrosensors • Measurement Sensors• Ultrasonic Sensors • Vision Sensors
Industrial Components • RFID/Code Readers • Relays • Pushbuttons & Indicators • Limit and Basic Switches • Timers • Counters • Metering Devices • Power Supplies
Safety • Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Hoffman Estates, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROPE B.V. • Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands. • +31 (0) 23 568 13 00 • www.industrial.omron.eu