© 2001, cisco systems, inc. 2-1 a_isis_primer overview of is-is technologies, structures and...
Post on 26-Mar-2015
221 Views
Preview:
TRANSCRIPT
© 2001, Cisco Systems, Inc. 2-1
A_ISIS_PrimerA_ISIS_Primer
Overview of IS-IS Technologies, Structures
and Protocols
Overview of IS-IS Technologies, Structures
and Protocols
© 2001, Cisco Systems, Inc. www.cisco.com 2-2
ObjectivesObjectives
Upon completion of this lesson, you will be able to to perform the following tasks:
• Describe the OSI protocol suite with special attention to the network layer
• Explain the principles of OSI routing
• List the prerequisites for the implementation of the IS-IS routing model in a network
• List the types of IS-IS routers and explain the principle of area routing
• Explain the purpose of Integrated IS-IS
• Configure, monitor and troubleshoot a simple IS-IS network
Introduction to OSI Protocols and IS-IS
Routing
Introduction to OSI Protocols and IS-IS
Routing
© 2001, Cisco Systems, Inc. www.cisco.com Overview of ISIS Technologies, Structures and Protocols 3
© 2001, Cisco Systems, Inc. www.cisco.com 2-4
ObjectivesObjectives
Upon completion of this section, you will be able to:
• Explain the terminology used in OSI
• List routing protocol examples for routing OSI protocols
• Describe the basic concepts of link-state routing
• Make a general comparison between Integrated IS-IS and OSPF
© 2001, Cisco Systems, Inc. www.cisco.com 2-5
OSI ProtocolsOSI Protocols
• ISO and OSI? • The International Organization for
Standardization (ISO) has been constituted to develop standards for data networking.
• The Open System Interconnection (OSI) protocols represent an international standardization program that facilitates multivendor equipment interoperability.
© 2001, Cisco Systems, Inc. www.cisco.com 2-6
OSI Protocols—(cont.)OSI Protocols—(cont.)
• The OSI protocol suite supports
• Numerous standard protocols at each of the OSI seven layers reference model
• OSI network-layer hierarchical addressing
• Two routing protocols at the network layer
© 2001, Cisco Systems, Inc. www.cisco.com 2-7
OSI Protocols—Terminology
OSI Protocols—Terminology
• Terminology used in OSI• End System (ES) is any non-routing network
nodes (host)
• Intermediate system (IS) is a router
• An area is a logical entity
–Formed by a set of contiguous routers, hosts and the data links that connect them
• Domain is a collection of connected areas
© 2001, Cisco Systems, Inc. www.cisco.com 2-8
OSI Protocol Suite and its Mapping to the OSI Reference Model
OSI Protocol Suite and its Mapping to the OSI Reference Model
© 2001, Cisco Systems, Inc. www.cisco.com 2-9
OSI Network Services—What to Route in OSI Environment?
OSI Network Services—What to Route in OSI Environment?
• Two types of OSI network-layer services are available to the OSI transport layer: • Connectionless Network Service (CLNS)
–CLNS performs datagram transport
• Connection-mode Network Service (CMNS)
–CMNS requires explicit establishment of paths between communicating transport-layer entities
© 2001, Cisco Systems, Inc. www.cisco.com 2-10
OSI Network Services— Connection-oriented Mode
OSI Network Services— Connection-oriented Mode
• CMNS/CONP:• CONP is an OSI network-layer protocol that
carries upper-layer data and error indications over connection-oriented links
• CMNS performs functions related to the explicit establishment of paths via CONP
• When support is provided for CMNS, the routing uses the X.25 protocols as the relaying functions
© 2001, Cisco Systems, Inc. www.cisco.com 2-11
OSI Network Services—Connectionless Mode
OSI Network Services—Connectionless Mode
• CLNS/CLNP:• CLNP is a an OSI network-layer protocol that
carries upper-layer data and error indications over connectionless links
• CLNS provides network-layer services to the transport layer via CLNP
• When support is provided for CLNS, the routing uses routing protocols to exchange routing information
© 2001, Cisco Systems, Inc. www.cisco.com 2-12
OSI Network Services—Routing Protocols
OSI Network Services—Routing Protocols
• ISO has developed standards for two types of protocols:• ES-IS dicovery protocols: “routing” between
End Systems and Intermediate Systems referred as level-0 “routing”
• IS-IS routing protocols: hierarchical (level-1, level-2 and level-3) routing between Intermediate Systems
© 2001, Cisco Systems, Inc. www.cisco.com 2-13
OSI Network Services—OSI Routing in Operation
OSI Network Services—OSI Routing in Operation
Area-1 Area-2
IS IS
IS IS
ESES
Domain
Level-0 routing between ESs and ISs on the same subnet
Level-1 routing between ISs within the same area
Level-2 routing between different areas within the same domain
Level-3 routing between separate domains
© 2001, Cisco Systems, Inc. www.cisco.com 2-14
OSI Network Services—IS-IS Routing
OSI Network Services—IS-IS Routing
• Intermediate System to Intermediate System (IS-IS) is a dynamic link-state routing protocol in ISO CLNS environment for routing CLNP• Link-state routing protocol in the OSI stack
• Alternative to IS-IS protocols is deploying CISCO ISO-IGRP or static routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-15
OSI Network Services—Recommended Reading OSI Network Services—Recommended Reading
• ISO 8473—documents the ISO Connectionless Network Protocol (CLNP)
• ISO/IEC 8348 appendix A—documents NSAP addresses
• ISO 9542—documents the ES-IS routing exchange protocol
• ISO/IEC 10589—documents IS-IS intra-domain routing exchange protocol
© 2001, Cisco Systems, Inc. www.cisco.com 2-16
Basic Terms of Link-State Routing Protocols
Basic Terms of Link-State Routing Protocols
• Link-state (LS) routers know much more about the network than their distance-vector relatives—LS routers cannot be fooled as easily into making wrong decisions
• Link-state routers keep track of:• Their neighbors
• All the routers in the network, or at least within the same area
• Best paths toward a destination
© 2001, Cisco Systems, Inc. www.cisco.com 2-17
Basic Terms—Link-State Data Structures
Basic Terms—Link-State Data Structures
• Neighbor table, formally known as an adjacency database (list of neighbors we are aware of)
• Topology table, typically referred to as a link-state database—LSDB (routers and links in the area/network)
• Routing table, commonly named a forwarding database (list of best paths to destinations)
© 2001, Cisco Systems, Inc. www.cisco.com 2-18
Basic Terms—The Best Path Calculation
Basic Terms—The Best Path Calculation
• Routers find the best paths to destinations by applying the Dijkstra Shortest Path First (SPF) algorithm to the link-state database• Every router in the area places itself into the
root of the tree that is built
• Best path is calculated with respect to the lowest total cost of links to a specific destination
• Best routes are put into the forwarding database
© 2001, Cisco Systems, Inc. www.cisco.com 2-19
Basic Terms—Link-State Environment
Basic Terms—Link-State Environment
x
CA
B
ED
GF H
Link-state database
Adjacency databaseNeighbors of x: A, B,C,D
CA
B
ED
GF H
Dijkstra (SPF)algorithm
Forwarding database(routing table)
Shortest paths
x
© 2001, Cisco Systems, Inc. www.cisco.com 2-20
Examples of Link-State ProtocolsExamples of Link-State Protocols
• OSPF (Open Shortest Path First), supports IP only; Internet standard
• DECnet Phase V, supports Decnet/OSI
• IS-IS (supports CLNP); ISO standard
• Integrated IS-IS (supports CLNS and IP); Internet standard, RFC-1195
• NLSP (Netware Link Services Protocol), supports IPX only, based on IS-IS
• PNNI (Private Network to Network Interface)— used in ATM “routing”
© 2001, Cisco Systems, Inc. www.cisco.com 2-21
Link-State Data Structure—Network Hierarchy
Link-State Data Structure—Network Hierarchy
• Link-state routing requires a hierachical network structure• Enforced by some LS protocols (for example,
OSPF)
• Some LS protocols are more tolerant (IS-IS)
• Two level hierarchy—areas• Backbone or level-2 area
• Non-backbone or level-1 area
© 2001, Cisco Systems, Inc. www.cisco.com 2-22
LS Data Structures—Link-State Database
LS Data Structures—Link-State Database
• The foundation for best-path calculation is the LS database• LS database has to be identical on all the
routers in the area—identical view
• Routers know everything about their respective area
• Routers know about the nearest exit point(s) to other areas or other routing domains
© 2001, Cisco Systems, Inc. www.cisco.com 2-23
LS Data Structures—Adjacency Database
LS Data Structures—Adjacency Database
• Routers discover neighbors by exchanging Hello packets• Routers declare neighbors “UP” after
checking some parameters/options
• Some routers become adjacent (tightly connected neighbors)—“good neighbors”
• Adjacent routers exchange topology information
© 2001, Cisco Systems, Inc. www.cisco.com 2-24
LS Data Structures—Link-State Packets
LS Data Structures—Link-State Packets
• Upon establishing neighbor relationship, routers exchange their pictures of the network• Full picture—link-state database (LSDB)—is
built by link-state packets (LS packets)
• LS packets report the states of links and routers
• LS packets are flooded reliably throughout the area/network
© 2001, Cisco Systems, Inc. www.cisco.com 2-25
LS Data Structures—Originating Link-State Packets
LS Data Structures—Originating Link-State Packets
• LS packets contain router information (state, interfaces, addresses, connected routers) • Originator of LS packet is a router itself
• LS packets are sequenced to prevent reflooding of the router’s own LS packet
• LS packets are aged when in the LS database—ageing out results in purging the packet
• Periodic refreshments of LS packets to prevent ageing out
© 2001, Cisco Systems, Inc. www.cisco.com 2-26
LS Data Structures—Link-State Maintenance
LS Data Structures—Link-State Maintenance
• Routers maintain the consistency of the link-state database• Routers check their neighbor relationship by
sending and receiving periodic hello packets
• Routers report changes in the network (immediately/depending on timers)
• Receivers of a link-state packet normally flood it further
• Routers periodically resend their part of the “network map” (even if no changes)
© 2001, Cisco Systems, Inc. www.cisco.com 2-27
Link-State Processes
© 2001, Cisco Systems, Inc. www.cisco.com 2-28
Link-State Processes—Receive and Update
Link-State Processes—Receive and Update
• Receive process:• Receives datagrams
• Forwards data to the Forward process
• Forwards routing protocol packets to the Update process
• Update process:• Creates link-state information
• Receives link-state information from neighbors
• Builds and maintains the link-state database
© 2001, Cisco Systems, Inc. www.cisco.com 2-29
Link-State Processes—Decision and Forward
Link-State Processes—Decision and Forward
• Decision process• Creates forwarding database by running
Dijkstra algorithm on the link-state database
• Forward process• Receives packets from the Receive process
• Forwards packets according to the forwarding database
• Manages load sharing, redirection and error reporting
© 2001, Cisco Systems, Inc. www.cisco.com 2-30
Benefits of Link-State Routing Benefits of Link-State Routing
• Benefits:• Fast convergence—changes reported
immediately by the source affected
• Robustness against routing loops:
–Routers know the topology
–LS packets numbered and acknowledged
• By careful (hierarchical) network design resources can be utilized optimally
© 2001, Cisco Systems, Inc. www.cisco.com 2-31
Caveats of Link-State RoutingCaveats of Link-State Routing
• Caveats:• Significant demands for resources:
–Memory (three tables: adjacency, topology, forwarding)
–CPU (Dijkstra algorithm can be intensive, especially when a lot of instabilities are present)
• Requires very strict network design (when more areas—area routing)
• Problems with partitioning of areas
© 2001, Cisco Systems, Inc. www.cisco.com 2-32
• Configuration generally simple but can be complex when tuning various parameters and when the design is complex
• Troubleshooting is easier than in distance vector routing—we have more information at hand (three databases)• Requires a good understanding of link-state
concepts
Benefits and Caveats of Link-State Routing
Benefits and Caveats of Link-State Routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-33
Integrated IS-IS vs. OSPFIntegrated IS-IS vs. OSPF
• Integrated IS-IS is an extended version of IS-IS for mixed ISO CLNS and IP environments • Integrated IS-IS (RFC1195) represents an
alternative to OSPF in the IP world• Integrated IS-IS and OSPF are both link-state
protocols with similar:
–Link-state representation, ageing, metrics
–Links-state databases, SPF alghoritms
–Update, desicion and flooding processes
© 2001, Cisco Systems, Inc. www.cisco.com 2-34
Integrated IS-IS vs. OSPF—Area Design
Integrated IS-IS vs. OSPF—Area Design
• Area design• OSPF is based on a central backbone with all
other areas being attached to it
– In OSPF the border is inside routers (ABRs)
–Each link belongs to one area
• In IS-IS the area borders lie on links
–Each IS-IS router belongs to exactly one area
– IS-IS allows a more flexible approach to extending the backbone
© 2001, Cisco Systems, Inc. www.cisco.com 2-35
Integrated IS-IS vs. OSPF— (cont.)
Integrated IS-IS vs. OSPF— (cont.)
• Resource usage• One link-state packet per IS-IS router in one
area (including redistributed prefixes) compared to many OSPF LSAs
• Scalability of link-state protocols has been proved (live ISP backbones)• Convergence capabilities are similar (same
algorithm)
• OSPF has more features (route tags, Stub/NSSA, OSPF over Demand Circuit…)
© 2001, Cisco Systems, Inc. www.cisco.com 2-36
SummarySummary
After completing this section, you should be ready to:
• Explain the terminology used on OSI
• List routing protocol examples for routing OSI protocols
• Describe the basic concepts of link-state routing
• Make a general comparison between Integrated IS-IS and OSPF
© 2001, Cisco Systems, Inc. www.cisco.com 2-37
Review QuestionsReview Questions
• Explain the meaning of the following abbreviations: OSI, ISO, IS and ES.
• How do ESs and ISs communicate?
• What types of network services does an OSI protocol stack support?
• Explain the CLNP’s position in an OSI stack.
• How many routing levels are supported in OSI routing?
• List the protocols that can be used for routing CLNS/CLNP.
• What are the differences between distance-vector and link-state routing protocols?
• What is common to OSPF and Integrated IS-IS?
Operation of IS-ISOperation of IS-IS
© 2001, Cisco Systems, Inc. www.cisco.com Overview of ISIS Technologies, Structures and Protocols 2- 38
© 2001, Cisco Systems, Inc. www.cisco.com 2-39
ObjectivesObjectives
Upon completion of this section, you will be able to:
• Prepare a proper addressing plan for IS-IS deployment
• Explain how networks and interfaces are represented in IS-IS
• List the types of IS-IS routers and their role in IS-IS area design
• Describe the hierarchical structure of IS-IS areas
• Describe the concept of establishing adjacencies
• Describe the concepts of routing traffic transport and database synchronization
© 2001, Cisco Systems, Inc. www.cisco.com 2-40
ISO IS-IS—IS-IS PDUISO IS-IS—IS-IS PDU
• IS-IS Protocol Data Units (PDU) are encapsulated directly into a data-link frame
• There is no CLNS or IP header in a PDU:• Hello (ESH, ISH, IIH)
• LSP (Non-pseudonode and Pseudonode)
• PSNP (Partial Sequence Numbers PDU)
• CSNP (Complete Sequence Numbers PDU)
© 2001, Cisco Systems, Inc. www.cisco.com 2-41
ISO IS-IS PDU—(cont.)ISO IS-IS PDU—(cont.)
• PDU (Protocol Data Unit) between peers
• Network PDU = datagram, packet
• Data Link PDU = frame
Data-link header (OSI family 0xFEFE)
IS-IS header (first byte is 0x83)
IS-IS TLVsIS-IS:
Data-link header (OSI family 0xFEFE)
ES-IS header (first byte is 0x82)
ES-IS TLVsES-IS:
Data-link header (OSI family 0xFEFE)
CLNP header (first byte is 0x81)
CLNSCLNP
© 2001, Cisco Systems, Inc. www.cisco.com 2-42
OSI Address AssignmentOSI Address Assignment
• OSI network layer addressing is implemented with network service access point (NSAP) addresses • NSAP address identifies any system in OSI
network
• Various NSAP formats for various systems
–Different protocols may use different representation of NSAP
© 2001, Cisco Systems, Inc. www.cisco.com 2-43
IS-IS NSAP Address—StructureIS-IS NSAP Address—Structure
• IS-IS (ISO/IEC 10589) distinguishes only 3 fields in NSAP address:• Area Address: variable length field composed of
high order octets excluding SystemID and SEL
• SystemID: ES or IS identifier in an area; fixed length of 6 octets in Cisco IOS
• NSEL: N-selector, service identifier
© 2001, Cisco Systems, Inc. www.cisco.com 2-44
OSI Addressing—IS-IS vs. ISO-IGRP NSAPs
OSI Addressing—IS-IS vs. ISO-IGRP NSAPs
• IS-IS NSAP is divided into three parts • 1 octet NSEL , 6 octets for System ID and from 1
to 13 octets for Area Address field
• Total length of NSAP from 8 (minimum) up to 20 octets (maximum)
• ISO-IGRP NSAP is divided as follows:• Area Address, composed of the first two octets of
the NSAP after the System ID and NSEL fields
• Domain, composed of high order octets (from 1 to 11) of the NSAP, excluding the Area, System ID and NSEL fields
• ISO-IGRP requires at least 10 bytes of NSAP
© 2001, Cisco Systems, Inc. www.cisco.com 2-45
OSI Addressing—Network Entity Title
OSI Addressing—Network Entity Title
• Network Service Access Point (NSAP)— address which (at the network layer) includes a service identifier (“protocol number”)
• Network Entity Title (NET)—NSAP with service identifier of 00
• Used in routers since they implement network layer only (base for SPF calculation)
• The official NSAP prefixes are required for CLNS routing—AFI 49 (Authority and Format Identifier) denotes private address space
© 2001, Cisco Systems, Inc. www.cisco.com 2-46
OSI Addressing—NET and System Identifier Rules
OSI Addressing—NET and System Identifier Rules
• NET must begin with an octet• 47.xxxx....;
• 0111.xxxx... Not 111.xxxx...
• NET must end with a single octet set to 00, identifying network entity (e.g. router) itself• ...xxxx.00
• System ID normally six octets (on Cisco six!) and has to be the same length everywhere
• Examples: 47.0001.0000.0c12.3456.00 01.1921.6811.1003.00
1047.0001.1234.5678.9101.00
© 2001, Cisco Systems, Inc. www.cisco.com 2-47
OSI Addressing—NSAP Examples
OSI Addressing—NSAP Examples
• Example 1: NSAP 47.0001.aaaa.bbbb.cccc.00• IS-IS: Area = 47.0001, System ID =
aaaa.bbbb.cccc, NSEL = 00
• ISO-IGRP: Domain = 47 Area = 0001, System ID = aaaa.bbbb.cccc, NSEL = 00
• Example 2: NSAP 39.0f01.0002.0000.0c00.1111.00• IS-IS: Area = 39.0f01.0002, Sysem ID =
0000.0c00.1111, NSEL = 00
• ISO-IGRP: Domain= 39.0f01 Area = 0002, System ID = 0000.0c00.1111, NSEL = 00
© 2001, Cisco Systems, Inc. www.cisco.com 2-48
Identifying Systems in IS-ISIdentifying Systems in IS-IS
• The Area Address uniquely identifies the routing area and the System ID identifies each node • All routers within an area must use the same
Area Address
• An ES may be adjacent to a level-1 router only if they both share a common Area Address
• Area Address is used in level-2 routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-49
Identifying Systems in IS-IS—System ID
Identifying Systems in IS-IS—System ID
• System ID may be the MAC address (CLNS) or IP address of an interface (IP world)• System ID used in level-1 routing and has to
be unique within an area (and of same length)
• System ID has to be unique within level-2 routers that form routing domain
• General recommendation: domain-wide unique System ID
© 2001, Cisco Systems, Inc. www.cisco.com 2-50
Identifying Systems—Subnetwork and CircuitIdentifying Systems—
Subnetwork and Circuit• SNPA (Subnetwork Point of Attachment)
identified by:• Encapsulation type or DLCI address on p2p
interfaces (HDLC, FR)
• MAC address on LAN interfaces (0000.0c12.3456)
• Interfaces uniquely identified by Circuit ID:• One octet number on point-to-point interfaces (03)
• Circuit ID concatenated with 6 octet System ID of a designated router on broadcast multi-access networks to form 7 octet LAN ID (1921.6811.1001.03)
© 2001, Cisco Systems, Inc. www.cisco.com 2-51
Identifying Systems—OSI Addressing in Network
Identifying Systems—OSI Addressing in Network
39.0002.3333.3333.3333.00
39.0001.2222.2222.2222.00
39.0001.1111.1111.1111.00
39. 0004.8888.8888.8888.00
39.0003.7777.7777.7777.00
39.0004.9999.9999.9999.00
39.0002.4444.4444.4444.00
39.0002.5555.5555.5555.00
39.0002.6666.6666.6666.00
© 2001, Cisco Systems, Inc. www.cisco.com 2-52
Link State Packets—Network Representation
Link State Packets—Network Representation
• Generally physical links can be placed in two groups:• Broadcast—multi-access subnetworks that
support addressing of a group of attached systems (LANs)
• Point-to-point links, multi-point links, dynamically established links
• Only two link-state representations are available in IS-IS:• Broadcast for LANs
• Point-to-point for all other topologies
© 2001, Cisco Systems, Inc. www.cisco.com 2-53
Link State Packets Representing Routers
Link State Packets Representing Routers
• Router describes itself with the Link State Packet (LSP)
• LSP header contents:
– PDU type, Length, LSP ID, Sequence Number, Remaining Lifetime
• Type Length Value (TLV) variable length fields:
– IS neighbors
– ES neighbors
– Authentication Information
– ....
LSP Header
IS neighbors
ES neighbors
...............
© 2001, Cisco Systems, Inc. www.cisco.com 2-54
LSP Representing Routers—LSP Header
LSP Representing Routers—LSP Header
• LSPs are numbered by a sequence number to prevent duplicates LSPs• Assists with synchronization
• Sequence numbers begin with 1
• Sequence numbers are increased to indicate newest LSP• LSPs in LSDB have a remaining lifetime
• Allows synchronization
• Decreasing timer
© 2001, Cisco Systems, Inc. www.cisco.com 2-55
LSP Representing Routers— Variables
LSP Representing Routers— Variables
• Router specific information is encoded in the variable field with TLVs (Type Length Value)
• Metric is associated with an outgoing interface• Four types (three optional, intended to be used in
Type-of-Service routing)
• Delay, default, expense and error—Cisco uses default metric only
© 2001, Cisco Systems, Inc. www.cisco.com 2-56
LSP Representing Routers—LAN Representation
LSP Representing Routers—LAN Representation
IS IS
DIS IS IS
Pseudonode—logically “connected” to all other nodes
NOTE: All (physical) routers still establish adjacency to each other
Logical Phisycal
© 2001, Cisco Systems, Inc. www.cisco.com 2-57
L1, L2 and L1/L2 RoutersL1, L2 and L1/L2 Routers
• Two-level structure of areas forms IS-IS domains
• Intermediate Systems can be:• L1, level-1 (equivalent to OSPF internal non-
backbone routers), responsible for intra-area routing
• L1/L2, level-1-2 (in OSPF these are area-border routers), performing intra- and inter-area routing
• L2, level-2 (backbone routers in OSPF), inter-area only
© 2001, Cisco Systems, Inc. www.cisco.com 2-58
L1 and L2 RoutersL1 and L2 Routers
• Level-1 (L1) routers referred to as Station routers
• L1 routers constitute an area
• L1 routers keep one copy of the link-state database (its own area “picture”; intra-area information only)
• They enable “stations” (ESs) to communicate
• Level-2 (L2) routers referred to as Area routers
• They store inter-area information
• They interconnect areas
© 2001, Cisco Systems, Inc. www.cisco.com 2-59
L1/L2 RouterL1/L2 Router
• Level-1-2 (L1/L2) routers keep two separate copies of the link-state databases• For level-1 and level-2
• Inform L1 routers about an exit point
• Level-1 area is a collection of L1 and L1/L2 routers
• Backbone area (level-2) is a set of L1/L2 and L2 routers and has to be contiguous
© 2001, Cisco Systems, Inc. www.cisco.com 2-60
L1, L2 and L1/L2 —LSP FeaturesL1, L2 and L1/L2 —LSP Features
• Two-level nature of IS-IS requires separate types of link-state packets
• level-1 and level-2 LSPs
• Designated IS is a representative of a LAN and performs additional duties
• Pseudo level-1 and level-2 LSPs on behalf of the LAN—separate DIS for L1 and L2; no backup DIS
• LSPs sent to a unicast address on point-to-point links and to a multicast address on broadcast multi-access networks
© 2001, Cisco Systems, Inc. www.cisco.com 2-61
Example #1: Area Configuration—Physical View
Example #1: Area Configuration—Physical View
Area-1 Area-2
R3 R2
R1 R4
L1L2 routers
L1 routers
• R2 and R3 belong to their respective level-1 areas and provide a physical connection between them
© 2001, Cisco Systems, Inc. www.cisco.com 2-62
Example #1: Area Configuration—Logical View
Example #1: Area Configuration—Logical View
L1
R3 R2
R1 R4
• R2 and R3 are still L1 routers but in addition they provide an entry point to the level-2 backbone interconnecting both level-1 areas
L2
L2
L1 L1
© 2001, Cisco Systems, Inc. www.cisco.com 2-63
Example #2: L2 and L1/L2 Routers Forming L2 Backbone
Example #2: L2 and L1/L2 Routers Forming L2 Backbone
L1L2
L1L2
Backbone links
L1L2
L1L2
L1-only
L2-only
L1-only
Area-2
Area-1
Area-3
Area-4L1-only
L1-only
L1L2
IS-IS domain
This router must behave as level-2 as well in order to guarantee backbone continuity.
© 2001, Cisco Systems, Inc. www.cisco.com 2-64
Identifying Types of Systems—Hello Messages
Identifying Types of Systems—Hello Messages
• Periodic hello messages (Hello PDU) are used, as in any other link-state protocol
• Three types:
• ESH (End System Hello), between ES and IS
• ISH (Intermediate System Hello), sent by IS to ES
• IIH (IS to IS Hello, used between two ISs)
• Hellos carry information on the system itself, its capabilities and interface parameters
© 2001, Cisco Systems, Inc. www.cisco.com 2-65
Identifying Types of Systems— ES and IS Hello Packets
Identifying Types of Systems— ES and IS Hello Packets
ES
IS-IS IS
ES-IS
IS
SNPA
ESES
IS SNPA
ESH
ISH
IIH
© 2001, Cisco Systems, Inc. www.cisco.com 2-66
IS-IS and ES-IS CommunicationIS-IS and ES-IS Communication
• Intermediate Systems establish and maintain neighbor relationships through the use of IS to IS hellos (IIH)
• Then they exchange LSPs
• End Systems do not need any configuration for finding their respective IS
• End Systems listen to IS hellos (ISH) to find their “way to the world”
• Initially ES picks a router randomly (whichever is heard)
© 2001, Cisco Systems, Inc. www.cisco.com 2-67
IS-IS and ES-IS Communication —(cont.)
IS-IS and ES-IS Communication —(cont.)
• Routers listen to ESH and thus find all the end systems on a segment• Routers include information on End Systems
in link-state packets
• Routers send Redirect message to help ES in finding the most optimal exit from a segment
© 2001, Cisco Systems, Inc. www.cisco.com 2-68
Neighbors and AdjacenciesNeighbors and Adjacencies
• IIH (IS to IS Hello) between routers• Two types of Hellos on LAN—L1 and L2
• Only one on p2p (with the type of desired adjacency described—L1, L2 or both)
• Hellos sent every 10 seconds, hold-time 30 seconds (default)
• Separate adjacencies are built for L1 and L2 routers• L1/L2 routers keep two tables
• Routers form adjacencies with all other routers and send LSPs to all routers on the LAN (unlike OSPF routers)
© 2001, Cisco Systems, Inc. www.cisco.com 2-69
LAN AdjacenciesLAN Adjacencies
L1
L1/L2 L1/L2 L1
L1 adjacency L2 adjanceny
• Adjacencies are established based on the area address announced in the incoming IIHs and the type of the router
L1/L2 L1/L2
L1/L2
Area-1
Area-1
Area-1 Area-1
Area-2
© 2001, Cisco Systems, Inc. www.cisco.com 2-70
WAN AdjacenciesWAN Adjacencies
L1 L1
L1/L2
Area-1 Area-1
L1/L2 L1 L1/L2
Area-1 Area-1
L1
L2 L2
Area-1 Area-1
Area-1 Area-2
L1
L1L2
L1
#
L1/L2 L2 L1/L2
Area-1 Area-1L2
L1/L2 L2 L1/L2
Area-1 Area-2L2
L2
L1/L2 L1/L2Area-1 Area-1
© 2001, Cisco Systems, Inc. www.cisco.com 2-71
Continous Flow of L2 Adjacencies
Continous Flow of L2 Adjacencies
L1L2
L1L2
L1L2
L2-only
L1-only
L1-only
L1L2
Area-1
Area-2
Area-3
L1 adjacenciesL2 adjacenciesL1 and L2 adjacencies
• Area-1 and Area-2 are level-1 areas
• Level-2 backbone is a set of L1/L2 and L2 routers and overlaps attached level-1 areas
© 2001, Cisco Systems, Inc. www.cisco.com 2-72
Update, Decision and Flooding Processes
Update, Decision and Flooding Processes
• No routes calculated before the “map of the network” built—no “map” built before adjacencies established
• The network map is built through an Update process in the router
• Network changes reflected immediately (depending on timer settings) through link-state updates
© 2001, Cisco Systems, Inc. www.cisco.com 2-73
Update, Decision and Flooding Processes
Update, Decision and Flooding Processes
• SPF topology based on NETs• IP subnets are treated similarly to ES (in LSP
and link-state database)
• Changes of IP information (or ESs) do not lead to full SPF recalculation—partial route calculation (PRC) run only—optimization
© 2001, Cisco Systems, Inc. www.cisco.com 2-74
Update, Decision and Flooding Processes
Update, Decision and Flooding Processes
• LSP originated at the source of a change (for example, link coming up)• LSP received by other routers and flooded in
a controlled way through all the adjacencies
• LSPs periodically reflooded to refresh the link-state database (Remaining Lifetime)
• SNP (Sequence Numbers PDU) packets used to ensure synchronization and reliability
© 2001, Cisco Systems, Inc. www.cisco.com 2-75
LSDB SynchronizationLSDB Synchronization
• SNP (Sequence Number PDU) packets used to ensure synchronization and reliability
• Contents are “LSP descriptions”
• PSNP (Partial SNP) used:
• For acknowledgment of LSPs on p2p links
• To request missing pieces of link-state database
• CSNP (Complete SNP) used:
• Periodically by DIS on LAN to ensure reliability
• On point-to-point link when the link comes up
© 2001, Cisco Systems, Inc. www.cisco.com 2-76
LSDB Synchronization—P2PLSDB Synchronization—P2P
R1 R3 LSP 33
PSNP
III. ACK: Thank you for
LSP 33I. Link
went down
II. New LSP describing the
current situation
s0
R2
© 2001, Cisco Systems, Inc. www.cisco.com 2-77
LSDB Synchronization—LANLSDB Synchronization—LAN
R1
CSNP sent periodically (every 10 s) by DIS
R2/DIS
PSNP
II. Request: Sorry. I
missed LSP 77 CSNP
PSNP
I. CSNP:LSP76LSP77LSP88
© 2001, Cisco Systems, Inc. www.cisco.com 2-78
SummarySummary
After completing this section, you should be able to:
• Prepare a proper addressing plan for IS-IS deployment
• Explain how networks and interfaces are represented in IS-IS
• List the types of IS-IS routers and their role in IS-IS area design
• Describe the hierarchical structure of IS-IS areas
• Describe the concept of establishing adjacencies
• Describe the concepts of routing traffic transport and database synchronization
© 2001, Cisco Systems, Inc. www.cisco.com 2-79
Review QuestionsReview Questions
• How is the router identified in an IS-IS environment?
• What is the difference between NSAP and NET?
• What does a unique System ID define?
• Which network representations are supported by IS-IS?
• What is a pseudonode?
• List the types of IS-IS routers.
• How do two level-1 areas communicate?
• How do systems find each other in IS-IS?
• List the types of adjacencies between IS-IS systems.
• How is LSDB synchronization done in IS-IS?
IP and OSI Routing with Integrated IS-ISIP and OSI Routing
with Integrated IS-IS
© 2001, Cisco Systems, Inc. www.cisco.com Overview of ISIS Technologies, Structures and Protocols 2-80
© 2001, Cisco Systems, Inc. www.cisco.com 2-81
ObjectivesObjectives
Upon completion of this section, you will be able to perform the following tasks:
• Determine how CLNS and IP networks are represented in LSPs
• Determine how a router builds OSI and IP forwarding tables
• Explain the basic principles of area routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-82
Integrated IS-IS Routing ProtocolIntegrated IS-IS Routing Protocol
• Integrated IS-IS allows for three types of routing domains (OSI, IP, Dual)
• Therefore, an IS-IS LSP may contain multiple variable length fields (TLV)• Some contain OSI-specific information
• Some contain IP-specific information
© 2001, Cisco Systems, Inc. www.cisco.com 2-83
Integrated IS-IS—Representing IP Networks
Integrated IS-IS—Representing IP Networks
• LSP describes IP information in the same way as ESs
• Integrated IS-IS has all the features of modern routing protocols• Variable length mask
• Redistribution
• Summarization
© 2001, Cisco Systems, Inc. www.cisco.com 2-84
Integrated IS-IS—NET Address Planning
Integrated IS-IS—NET Address Planning
• Common CLNS parameters (NET) and Area planning are still required even in an IP environment• Even when Integrated IS-IS is used only for IP
routing, routers still establish CLNS adjacencies and use CLNS packets
© 2001, Cisco Systems, Inc. www.cisco.com 2-85
OSI Area Routing—Building OSI Forwarding Table
OSI Area Routing—Building OSI Forwarding Table
• When databases are synchronized, Dijkstra (SPF) algorithm is run on the LSDB to calculate the SPF tree• Criteria: the shortest path to the destination is
the lowest total sum of metrics
• Separate route calculations made for L1 and L2 areas in L1/L2 routers
• Partial route calculation (PRC) run to calculate ES reachability
• Best paths are placed in the OSI L1 and the L2 forwarding table
© 2001, Cisco Systems, Inc. www.cisco.com 2-86
OSI Area RoutingOSI Area Routing
• Level-1 intermediate systems• Routing within the area is based on the System ID
portion of the ISO address
• If the destination belongs to another area, they route to the nearest active level-1-2 router
• Level-2 intermediate systems• Routing between areas is based on the Area
Address and considers only the area cost
• If the destination belongs to the same area, they use the least-cost path to the System ID
© 2001, Cisco Systems, Inc. www.cisco.com 2-87
OSI Area Routing—Routing Between Areas
OSI Area Routing—Routing Between Areas
• From level-1 via level-2 to level-1 • L1 always sends a packet to a nearest active
L1/L2 router (default routing)
• Then the packet travels via L2 routing towards the destination area where the best L1 path is used
• Note: L1/L2 router performs L1 and L2 routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-88
OSI Area Routing—Suboptimal Inter-area Routing
OSI Area Routing—Suboptimal Inter-area Routing
L1L2
L1L2
L1L2L1L2
L2
Area-2
Area-1
Area-3
Area-4
Area-5
R2
R1
Network path from router R2 to R1Network path from router R1 to R2
L2
10
15
10
10
10
10
10 15
R2 takes the closest exit; then L1L2 takes the closest entry
10
© 2001, Cisco Systems, Inc. www.cisco.com 2-89
OSI Area Routing— Interconnecting IS-IS Domains
OSI Area Routing— Interconnecting IS-IS Domains
• IS-IS routing domain is a collection of IS-IS areas
• When interconnecting IS-IS domains the following applies:• In pure IP-environment use BGP
• In pure CLNS use ISO-IGRP or static CLNS routes
© 2001, Cisco Systems, Inc. www.cisco.com 2-90
Example #1: OSI Intra- and Inter-area Routing
Example #1: OSI Intra- and Inter-area Routing
Area 49.0001 Area 49.0002
R5 - L2 R2 - L1L2
R1 - L1
L2
L1
• Routing in a two-level area structure
R4 - L1
L1
L1
S0
S1
S0
S1
E0 E0
© 2001, Cisco Systems, Inc. www.cisco.com 2-91
Example #1—Level-1 and Level-2 Topology Table
Example #1—Level-1 and Level-2 Topology Table
R1#show isis topologyIS-IS paths to level-1 routersSystem Id Metric Next-Hop Interface SNPAR1 --R2 10 R2 Se0 *HDLC*R4 10 R4 Se1 *HDLC*
R2#show isis topologyIS-IS paths to level-1 routersSystem Id Metric Next-Hop Interface SNPAR1 10 R1 Se0 *HDLC*R2 --R4 10 R4 Se1 *HDLC*IS-IS paths to level-2 routersSystem Id Metric Next-Hop Interface SNPAR2 --R5 10 R5 Et0 0010.7bb5.9e20
© 2001, Cisco Systems, Inc. www.cisco.com 2-92
Example #1—Intra-area Routing on R1
Example #1—Intra-area Routing on R1
R1#show clns routeCLNS Prefix Routing Table49.0001.0000.0000.0001.00, Local NET Entry
R1#show isis routeIS-IS Level-1 Routing Table - version 312System Id Next-Hop Interface SNPA Metric StateR2 R2 Se0 *HDLC* 10 Up L2-ISR4 R4 Se1 *HDLC* 10 UpR1 --Default route out of area - (via 2 L2-attached ISs)System Id Next-Hop Interface SNPA Metric State
R2 Se0 *HDLC* 10 Up
© 2001, Cisco Systems, Inc. www.cisco.com 2-93
Example #1—Intra- and Inter-area Routing on R2
Example #1—Intra- and Inter-area Routing on R2
R2#show clns routeCLNS Prefix Routing Table49.0001.0000.0000.0002.00, Local NET Entry49.0002 [110/10] via R5, IS-IS, Up, Ethernet049.0001 [110/0] via R2, IS-IS, Up
R2#show isis routeIS-IS Level-1 Routing Table - version 47System Id Next-Hop Interface SNPA Metric StateR4 R4 Se1 *HDLC* 10 UpR1 R1 Se0 *HDLC* 10 Up
© 2001, Cisco Systems, Inc. www.cisco.com 2-94
Example #1—Which Route in L1?Example #1—Which Route in L1?
R1#which-route 49.0001.0000.0000.0002.00 - (R2 NSAP)Route look-up for destination 49.0001.0000.0000.0002.00 Found route in IS-IS level-1 routing tableAdjacency entry used:System Id Interface SNPA State Holdtime Type Protocol0000.0000.0002 Se0 *HDLC* Up 26 L1 IS-IS Area Address(es): 49.0001 Uptime: 00:09:50
R1#which-route 49.0002.0000.0000.0005.00 - (R5 NSAP)Route look-up for destination 49.0002.0000.0000.0005.00 Using route to closest IS-IS level-2 routerAdjacency entry used:System Id Interface SNPA State Holdtime Type Protocol0000.0000.0002 Se0 *HDLC* Up 27 L1 IS-IS Area Address(es): 49.0001 Uptime: 00:09:57
© 2001, Cisco Systems, Inc. www.cisco.com 2-95
Example #1—Which Route in L2?Example #1—Which Route in L2?
R5#which-route 49.0001.0000.0000.0002.00 (R2 NSAP) Found route in CLNS L2 prefix routing tableRoute entry used:i 49.0001 [110/10] via R2, Ethernet0/0Adjacency entry used:System Id Interface SNPA State Hold. Type ProtR2 Et0/0 0000.0c92.e515 Up 24 L2 IS-IS Area Address(es): 49.0001
R5#which-route 49.0001.0000.0000.0001.00 (R1 NSAP)Found route in CLNS L2 prefix routing tableRoute entry used:i 49.0001 [110/10] via R2, Ethernet0/0Adjacency entry used:System Id Interface SNPA State Hold. Type Prot.R2 Et0/0 0000.0c92.e515 Up 21 L2 IS-IS Area Address(es): 49.0001
© 2001, Cisco Systems, Inc. www.cisco.com 2-96
Building IP Forwarding TableBuilding IP Forwarding Table
• PRC is also run to calculate IP reachability• Since IP and ES are represented as leaf objects
they do not participate in SPF
• Best paths are placed in the IP forwarding table following IP preferential rules• They appear as L1 or L2 IP routes
© 2001, Cisco Systems, Inc. www.cisco.com 2-97
Building IP Forwarding Table (cont.)
Building IP Forwarding Table (cont.)
Area 49.0001 Area 49.0002
R5- L2 R2 - L1L2
R1 - L1
L2
L1
R4 - L1
L1
L1
The IP addresses on loopbacks of routers are 1.0.0.1/8-R1, 2.0.0.1/8-R2, 4.0.0.1/8-R4 and 5.0.0.1/8-R5.R2#sh ip routei L1 1.0.0.0/8 [115/10] via 10.12.0.1, Ser0 -(R1)i L1 4.0.0.0/8 [115/10] via 10.24.0.4, Ser1 -(R4) i L2 5.0.0.0/8 [115/10] via 11.0.0.10, Eth0 -(R5)
S0 S1
E0
© 2001, Cisco Systems, Inc. www.cisco.com 2-98
SummarySummary
After completing this section, you should be able to perform the following tasks:
• Determine how CLNS and IP networks are represented in LSPs
• Determine how a router builds OSI and IP forwarding tables
• Explain the basic principles of area routing
© 2001, Cisco Systems, Inc. www.cisco.com 2-99
Review QuestionsReview Questions
• What is Dual ISIS?
• Is a NET address still required even when Integated IS-IS is run only for IP?
• How are IP subnets represented in the IS-IS environment?
• Describe the process of building OSI and IP forwarding tables?
• What is the principle of area routing?
Basic Integrated IS-IS Router ConfigurationBasic Integrated IS-IS Router Configuration
© 2001, Cisco Systems, Inc. www.cisco.com Overview of ISIS Technologies, Structures and Protocols 2-100
© 2001, Cisco Systems, Inc. www.cisco.com 2-101
ObjectivesObjectives
Upon completion of this section, you will be able to perform the following tasks:
• Configure Cisco routers for basic Integrated IS-IS operation
• Inspect basic Integrated IS-IS parameters on Cisco routers
© 2001, Cisco Systems, Inc. www.cisco.com 2-102
Integrated IS-IS Configuration Steps
Integrated IS-IS Configuration Steps
• Step1: Define areas, prepare addressing plan (NETs) for routers and determine interfaces
• Step2: Enable IS-IS in a router
• Step3: Configure the NET
• Step4: Enable Integrated IS-IS on the proper interfaces—do not forget interfaces to stub IP networks, such as loopbacks (although no CLNS neighbors there)
© 2001, Cisco Systems, Inc. www.cisco.com 2-103
router isis [tag]
router(config)#
• Enable the IS-IS routing protocol; tag—name for a process; when routing of clns packet is also needed use the clns routing command
IS-IS Configuration Steps—IS-IS Survival Kit Commands
IS-IS Configuration Steps—IS-IS Survival Kit Commands
ip router isis [tag]clns router isis [tag]
router(config-if)#
• Start an IS-IS routing process on an interface (IP, CLNS, both)
net network-entity-title
router(config-router)#
• Configure an IS-IS NET address for the routing process
© 2001, Cisco Systems, Inc. www.cisco.com 2-104
is-type {level-1 | level-1-2 | level-2-only}
router(config-router)#
• Configure the IS-IS level globally on a router; default = L1/L2 (station/area)
IS-IS Configuration Steps—IS-IS Good to Know Commands
IS-IS Configuration Steps—IS-IS Good to Know Commands
isis circuit-type {level-1 | level-1-2 | level-2-only}
router(config-if)#
• Configure the type of adjacency on an interface; default = L1/L2
isis metric default-metric {level-1 | level-2}
router(config-if)#
• Configure the metric for an interface; default = 10
© 2001, Cisco Systems, Inc. www.cisco.com 2-105
IS-IS Configuration Steps—Simple Integrated IS-IS Example
IS-IS Configuration Steps—Simple Integrated IS-IS Example
• The configured router acts as IP-only L1/L2 router
router isis net 01.0001.0000.0000.0002.00!interface ethernet 0 ip address 10.1.1.1 255.255.255.0 ip router isis!interface serial 0 ip address 10.1.2.1 255.255.255.0 ip router isis
router isis net 01.0001.0000.0000.0002.00!interface ethernet 0 ip address 10.1.1.1 255.255.255.0 ip router isis!interface serial 0 ip address 10.1.2.1 255.255.255.0 ip router isis
© 2001, Cisco Systems, Inc. www.cisco.com 2-106
Example #1: Sample Two-area Configuration
Example #1: Sample Two-area Configuration
Area 49.0001 Area 49.0002
R3 R2
R1 R4
L1L2 routers
L1 routers
E0
S0
• Configure routers for routing IP within two-level area structure
S0 S0
S0
E0
© 2001, Cisco Systems, Inc. www.cisco.com 2-107
Example #1: Sample Two-area Configuration (L1 routers)
Example #1: Sample Two-area Configuration (L1 routers)
• R1 has to be L1-only router
hostname R1!interface Serial0 ip address 192.168.120.1 255.255.255.0 ip router isis!router isis is-type level-1 net 49.0001.1921.6800.1005.00
hostname R1!interface Serial0 ip address 192.168.120.1 255.255.255.0 ip router isis!router isis is-type level-1 net 49.0001.1921.6800.1005.00
© 2001, Cisco Systems, Inc. www.cisco.com 2-108
Example #1: Sample Two-area Configuration (L1/L2 routers)
Example #1: Sample Two-area Configuration (L1/L2 routers)
• R2 has to be L1/L2-router (optimized)hostname R2!interface Ethernet0 ip address 192.168.220.2 255.255.255.0 ip router isis isis circuit-type level-2!interface Serial0 ip address 192.168.120.2 255.255.255.0 ip router isis isis circuit-type level-1!router isis net 49.0001.1921.6800.1006.00
hostname R2!interface Ethernet0 ip address 192.168.220.2 255.255.255.0 ip router isis isis circuit-type level-2!interface Serial0 ip address 192.168.120.2 255.255.255.0 ip router isis isis circuit-type level-1!router isis net 49.0001.1921.6800.1006.00
© 2001, Cisco Systems, Inc. www.cisco.com 2-109
show clns
router#
• Display information about the CLNS network
Troubleshooting Commands—CLNS
Troubleshooting Commands—CLNS
show clns protocol [tag]
router#
• List the protocol-specific information
show clns interface [type number]
router#
• List the CLNS-specific information about each interface
show clns neighbors [type number] [detail]
router#
• Display both ES and IS neighbors
© 2001, Cisco Systems, Inc. www.cisco.com 2-110
show isis route
router#
• Display IS-IS level-1 routing table
Troubleshooting Commands— CLNS and IS-IS
Troubleshooting Commands— CLNS and IS-IS
show clns route
router#
• Display CLNS routing table
show isis database
router#
• Display the IS-IS Link-State database
© 2001, Cisco Systems, Inc. www.cisco.com 2-111
show ip protocols
router#
• Display the parameters and current state of the active routing protocol process
Troubleshooting Commands—IPTroubleshooting Commands—IP
show ip route [address [mask]] | [protocol [process-id]]
router#
• Display the current state of the routing table
© 2001, Cisco Systems, Inc. www.cisco.com 2-112
Example #2: Simple Troubleshooting—What About CLNS Protocol?
Example #2: Simple Troubleshooting—What About CLNS Protocol?
R2#show clns protocol
IS-IS Router: <Null Tag> System Id: 1921.6800.1006.00 IS-Type: level-1-2 Manual area address(es): 49.0001 Routing for area address(es): 49.0001 Interfaces supported by IS-IS: Serial0 - IP
Eethernet0 - IP Redistribute: static (on by default) Distance for L2 CLNS routes: 110 RRR level: level-1 Generate narrow metrics: level-1-2 Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none
© 2001, Cisco Systems, Inc. www.cisco.com 2-113
Example #2: Are Adjacencies Established?
Example #2: Are Adjacencies Established?
R2#show clns neighborsSystem Id Interface SNPA State Holdtime Type ProtocolR1 Se0 *HDLC* Up 28 L1 IS-ISR3 Et0 0000.0c92.de4c Up 20 L2 IS-IS
R2#show clns interface serial 0Serial0 is up, line protocol is up Checksums enabled, MTU 1500, Encapsulation HDLC ERPDUs enabled, min. interval 10 msec. RDPDUs enabled, min. interval 100 msec., Addr Mask enabled Congestion Experienced bit set at 4 packets CLNS fast switching disabled CLNS SSE switching disabled DEC compatibility mode OFF for this interface Next ESH/ISH in 12 seconds Routing Protocol: IS-IS Circuit Type: level-1 Interface number 0x1, local circuit ID 0x101 Level-1 Metric: 10, Priority: 64, Circuit ID: R2.00 Number of active level-1 adjacencies: 1 Next IS-IS Hello in 5 seconds
© 2001, Cisco Systems, Inc. www.cisco.com 2-114
Example #2: Is Integrated IS-IS Running?
Example #2: Is Integrated IS-IS Running?
R2#show ip protocols
Routing Protocol is "isis" Sending updates every 0 seconds Invalid after 0 seconds, hold down 0, flushed after 0 Outgoing update filter list for all interfaces is Incoming update filter list for all interfaces is Redistributing: isis Address Summarization: None Routing for Networks: Serial0 Ethernet0Routing Information Sources: Gateway Distance Last Update 11.0.0.1 115 00:11:44 13.0.0.1 115 00:11:44 14.0.0.1 115 00:11:44Distance: (default is 115)
© 2001, Cisco Systems, Inc. www.cisco.com 2-115
Example #2: Do We See Any IP Routes?
Example #2: Do We See Any IP Routes?
R2#show ip route isis
i L1 11.0.0.0/8 [115/10] via 192.168.20.1, Serial0i L1 13.0.0.0/8 [115/10] via 192.168.220.3, Ethernet0i L1 14.0.0.0/8 [115/20] via 192.168.220.3, Ethernet0
© 2001, Cisco Systems, Inc. www.cisco.com 2-116
SummarySummary
After completing this section, you should be able to perform the following tasks:
• Configure Cisco routers for basic Integrated IS-IS operation
• Inspect Cisco routers IS-IS configuration at an entry level
© 2001, Cisco Systems, Inc. www.cisco.com 2-117
Review QuestionsReview Questions
• How is IS-IS routing enabled on Cisco routers?
• In which configuration mode are NETs defined?
• List at least two commands for checking CLNS parameters on a Cisco router.
• How are IP routes found that were added to the routing table by Integrated IS-IS?
© 2001, Cisco Systems, Inc. www.cisco.com 2-118
SummarySummary
After completing this lesson, you should be able to:
• Describe the OSI protocol suite with special attention to the network layer
• Explain the principles of OSI routing
• List the prerequisites for the implementation of the IS-IS routing model in a network
• List the types of IS-IS routers and explain the principle of area routing
• Explain the purpose of Integrated IS-IS
• Configure, monitor and troubleshoot a simple IS-IS network
© 2001, Cisco Systems, Inc. www.cisco.com Overview of IS-IS Technologies, Structures and Protocols 119
top related