2007 cisco systems, inc. all rights public ite pc v4.0 chapter 1 1 rip version 1 routing protocols...
Post on 18-Jan-2018
221 Views
Preview:
DESCRIPTION
TRANSCRIPT
© 2007 Cisco Systems, Inc. All rights reserved. Cisco PublicITE PC v4.0Chapter 1 1
RIP version 1
Routing Protocols and Concepts – Chapter 5Modified by Tony Chen
06/10/2008
ITE PC v4.0Chapter 1 2© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Notes: If you see any mistake on my PowerPoint slides or if
you have any questions about the materials, please feel free to email me at chento@cod.edu.
Thanks!
Tony ChenCollege of DuPageCisco Networking Academy
ITE PC v4.0Chapter 1 3© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Objectives Describe the functions, characteristics, and operation
of the RIPv1 protocol.
Configure a device for using RIPv1.
Verify proper RIPv1 operation.
Describe how RIPv1 performs automatic summarization.
Configure, verify, and troubleshoot default routes propagated in a routed network implementing RIPv1.
Use recommended techniques to solve problems related to RIPv1
ITE PC v4.0Chapter 1 4© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIP Historical Impact RIP evolved from an earlier protocol
developed at Xerox, called Gateway Information Protocol (GWINFO).
With the development of Xerox Network System (XNS), GWINFO evolved into RIP.
It later gained popularity because it was implemented in the Berkeley Software Distribution (BSD) as a daemon named routed (pronounced "route-dee", not "rout-ed").
Recognizing the need for standardization of the protocol, Charles Hedrick wrote RFC 1058 in 1988, in which he documented the existing protocol and specified some improvements.
Since then, RIP has been improved with RIPv2 in 1994 and with RIPng in 1997. IPv6 form of RIP called
RIPng (next generation) is now available
ITE PC v4.0Chapter 1 5© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv1 RIP Characteristics
–A classful, Distance Vector (DV) routing protocol–Metric = hop count–Routes with a hop count > 15 are unreachable–Updates are broadcast every 30 seconds–The data portion of a RIP message is encapsulated into a UDP segment, with both source and destination port numbers set to 520.
ITE PC v4.0Chapter 1 6© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv1 RIP Message Format RIP header - divided into 3 fields
–Command field•REQUEST (1)- Request either a partial or full table update from another RIP router. •RESPONSE (2) - A response to a request.
–Version field•1 or 2
–Must be zero•Must be zero" fields provide room for future expansion of the protocol.
Route Entry - composed of 3 fields
–Address family identifier•CLNS, IPX, IP etc.
–IP address–Metric
ITE PC v4.0Chapter 1 7© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv1
RIP Operation–RIP uses 2 message types:
Request message
-This is sent out on startup by each RIP enabled interface
-Requests all RIP enabled neighbors to send routing table
Response message
-Message sent to requesting router containing routing table
ITE PC v4.0Chapter 1 8© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv1 IP addresses initially divided
into classes
-Class A
-Class B
-Class C
RIP is a classful routing protocol
-Does not send subnet masks in routing updates
ITE PC v4.0Chapter 1 9© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Common RIP configuration issues
RIP and IGRP:
Classful network statements only
IOS will take subnetted networks but will translate it into the classful network for the running-config.
ITE PC v4.0Chapter 1 10© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RIPv1 Administrative Distance
–RIP’s default administrative distance is 120
ITE PC v4.0Chapter 1 11© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Basic RIPv1 Configuration A typical topology suitable for
use by RIPv1 includes:-Three router set up -No PCs attached to
LANs
-Use of 5 different IP subnets
ITE PC v4.0Chapter 1 12© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Basic RIPv1 Configuration Router RIP Command
–To enable RIP enter:-Router rip at the global configuration
prompt-Prompt will look like R1(config-router)#
ITE PC v4.0Chapter 1 13© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Basic RIPv1 Configuration Specifying Networks
–Use the network command to:-Enable RIP on all interfaces that belong to this network-Advertise this network in RIP updates sent to other routers every 30 seconds
ITE PC v4.0Chapter 1 14© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Verification and Troubleshooting
Show ip Route
To verify and troubleshoot routing -Use the following
commands:
-show ip route
-show ip protocols
-debug ip rip
ITE PC v4.0Chapter 1 15© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Verification and Troubleshooting show ip protocols
command
-Displaysrouting protocol
configured on router
POP QUIZ:What is the different
between the output of the command “show ip route” and “show ip protocol”?
ITE PC v4.0Chapter 1 16© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Verification and Troubleshooting Debug ip rip command
-Used to display RIP routing updates as they are happening
ITE PC v4.0Chapter 1 17© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Verification and Troubleshooting
Passive interface command
-Used to prevent a router from sending updates through an interface
-Example:
Router(config-router)#passive-interface interface-type interface-number
ITE PC v4.0Chapter 1 18© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Verification and Troubleshooting Passive interfaces
ITE PC v4.0Chapter 1 19© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Preventing routing updates through an interface Route filtering works by regulating the
routes that are entered into or advertised out of a route table.
As a result, a route filter influences which routes the router advertises to its neighbors.
On the other hand, routers running link state protocols determine routes based on information in the link-state database. Route filters have no effect on link-state advertisements or the link-state database.
(Tony) Route filtering could have negative effect on the link-state routing protocol.
Using the passive interface command can prevent routers from sending routing updates through a router interface, but the router continues to listen and use routing updates from that neighbor.
Keeping routing update messages from being sent through a router interface prevents other systems on that network from learning about routes dynamically.
Lab:
ITE PC v4.0Chapter 1 20© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Preventing routing updates through an interface
Again, this is only half the story.
When you use “passive interface” on a distance vector routing protocol, you need to complement it with “ip route” command.
It will break the rip update
You can use the “ip route” command to send route update
back to establish the 2 way communication
1
2
ITE PC v4.0Chapter 1 21© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Modified Topology The original scenario has been modified
such that:Three classful networks are used:172.30.0.0/16192.168.4.0/24192.168.5.0/24The 172.30.0.0/16 network is subnetted into three subnets:172.30.1.0/24172.30.2.0/24172.30.3.0/24The following devices are part of the 172.30.0.0/16 classful network address:All interfaces on R1S0/0/0 and Fa0/0 on R2
172.30.2.0
172.30.1.0
172.30.3.0
ITE PC v4.0Chapter 1 22© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Configuration Details
-To remove the RIP routing process use the following command
No router rip
-To check the configuration use the following command
Show run
ITE PC v4.0Chapter 1 23© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Boundary Routers
–RIP automatically summarizes classful networks–Boundary routers summarize RIP subnets from one major network to another.
ITE PC v4.0Chapter 1 24© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic SummarizationProcessing RIP Updates 2 rules govern RIPv1 updates:
-If a routing update and the interface it’s received on belong to the same network then
The subnet mask of the interface is applied to the network in the routing update
-If a routing update and the interface it’s received on belong to a different network then
The classful subnet mask of the network is applied to the network in the routing update.
ITE PC v4.0Chapter 1 25© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Sending RIP Updates
–RIP uses automatic summarization to reduce the size of a routing table.
ITE PC v4.0Chapter 1 26© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Advantages of automatic
summarization:
-The size of routing updates is reduced
-Single routes are used to represent multiple routes
which results in faster lookup in the routing table.
ITE PC v4.0Chapter 1 27© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Disadvantage of Automatic Summarization:
-Does not support discontiguous networks
ITE PC v4.0Chapter 1 28© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization Discontiguous
Topologies do not converge with RIPv1
A router will only advertise major network addresses out interfaces that do not belong to the advertised route.
ITE PC v4.0Chapter 1 29© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Automatic Summarization
ITE PC v4.0Chapter 1 30© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Default Route and RIPv1 Modified Topology: Scenario C
Default routes Packets that are not defined specifically in a routing table will go to the specified interface for the default route
Example: Customer routers use default routes to connect to an ISP router.
Command used to configure a default route is ip route 0.0.0.0 0.0.0.0 s0/0/1
ITE PC v4.0Chapter 1 31© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Default Route and RIPv1
ITE PC v4.0Chapter 1 32© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Default Route and RIPv1 Propagating the Default Route in RIPv1
Default-information originate command -This command is used to specify that the router is to originate default information, by propagating the static default route in RIP update.
ITE PC v4.0Chapter 1 33© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Default route with RIP
Centre#show ip routeCodes: C - connected, S - static, I - IGRP, R - RIP, M - mobile,
Gateway of last resort is not set
R 192.168.4.0/24 [120/1] via 192.168.2.1, 00:00:11, Serial0R 192.168.1.0/24 [120/1] via 192.168.2.1, 00:00:11, Serial0C 192.168.2.0/24 is directly connected, Serial0C 192.168.3.0/24 is directly connected, Ethernet0
Mobile#sho ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile,
Gateway of last resort is not set
R 192.168.4.0/24 [120/1] via 192.168.1.1, 00:00:04, Serial0
C 192.168.5.0/24 is directly connected, Ethernet0
C 192.168.1.0/24 is directly connected, Serial0
R 192.168.2.0/24 [120/1] via 192.168.1.1, 00:00:04, Serial0
R 192.168.3.0/24 [120/2] via 192.168.1.1, 00:00:04, Serial0
Centre(config)#ip route 0.0.0.0 0.0.0.0 loopback0Setup up a default route on the Centre router
Centre(config)#router ripCentre(config-router)#default-information originate
Centre#sh ip route
Codes: C - connected, S - static, * - candidate default
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
C 172.16.1.1 is directly connected, Loopback0
R 192.168.4.0/24 [100/8576] via 192.168.2.1, 00:00:22, Serial0
R 192.168.5.0/24 [120/2] via 192.168.2.1, 00:00:22, Serial0
S* 0.0.0.0/0 is directly connected, Loopback0
Mobile#sho ip route
Codes: C - connected, S - static, * - candidate default - RIP,
Gateway of last resort is 192.168.1.1 to network 0.0.0.0
R 192.168.4.0/24 [120/1] via 192.168.1.1, 00:00:09, Serial0
C 192.168.5.0/24 is directly connected, Ethernet0
C 192.168.1.0/24 is directly connected, Serial0
R 192.168.2.0/24 [120/1] via 192.168.1.1, 00:00:04, Serial0
R 192.168.3.0/24 [120/2] via 192.168.1.1, 00:00:09, Serial0
R* 0.0.0.0/0 [120/2] via 192.168.1.1, 00:00:09, Serial0
ITE PC v4.0Chapter 1 34© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Summary
RIP characteristics include:
Classful, distance vector routing protocol
Metric is Hop Count
Does not support VLSM or discontiguous subnets
Updates every 30 seconds
Rip messages are encapsulated in a UDP segment with source and destination ports of 520
ITE PC v4.0Chapter 1 35© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Summary: Commands used by RIPCommand Command’s purpose
Rtr(config)#router rip Enables RIP routing process
Rtr(config-router)#network Associates a network with a RIP routing process
Rtr#debug ip rip used to view real time RIP routing updates
Rtr(config-router)#passive-interface fa0/0 Prevent RIP updates from going out an interface
Rtr(config-router)#default-information originate Used by RIP to propagate default routes
Rtr#show ip protocols Used to display timers used by RIP
ITE PC v4.0Chapter 1 36© 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
top related