22. install the left fog light to the front bumper with three self-tapping screws. 23. install the...
Post on 24-Jan-2020
2 Views
Preview:
TRANSCRIPT
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2015 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
www.collegehillshonda.com
FOG LIGHTSserved. AII02278-08 (151
2016 CIVIC2- AND 4-DOOR
0) 0
Issue Date
OCT 2015
PARTS LIST
Fog Light KitP/N 08V31-TBA-100AP/N 08V31-TBA-100BP/N 08V31-TBA-100C
Right fog light
Left fog light
Right fog light trim(May not be used)
Left fog light trim(May not be used)
Fog light harness
Relay harness
Combination light switch
Fuse label
Wire tie with clip(May not be used)
Relay
14 Wire ties(Some may not be used)
1 of 248V31-TBA-1000-90
www.collegehillshonda.com
7 Long wire ties(Some may not be used)6 Self-tapping screws
20 A Fuse
Wire tie with holder
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Diagonal cutters
10 mm Socket
Isopropyl alcohol
Shop towel
Tape
Ruler
Scissors
10 mm Open-end wrench
Ratchet
Blanket
5 mm Hex wrench
The following tool is available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.
Plastic Trim Tool (T/N SILTRIMTL10)
2 of 24 AII02278-0
Illustration of the Fog Lights Installed in the Vehicle
INSTALLATION
1. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
COMBINATION LIGHT SWITCH
20 A FUSE
RELAYHARNESS
LEFT FOG LIGHT
FOG LIGHT HARNESS
RIGHT FOG LIGHT
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
2. Remove the driver’s dashboard lower cover andunplug the vehicle connectors and aspirator hose.
3. Remove the driver’s front door sill trim.
2 CLIPS
5 CLIPS
VEHICLECONNECTORS
ASPIRATOR HOSEVEHICLECONNECTOR
DRIVER’SDASHBOARDLOWER COVER
2 CLIPS
DRIVER’S FRONTDOOR SILL TRIM
3 CLIPS
4 RETAININGTABS
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
4. Pull away the door opening seal and remove the driver’s kick panel.
5. Lower the steering wheel. Apply the tape to the upper column cover as shown.
DOOR OPENING SEAL(Pull away.)
2 CLIPSDRIVER’SKICK PANEL
STEERINGWHEEL
UPPER COLUMNCOVER
TAPE
8 (1510) 3 of 24
www.collegehillshonda.com
6. If necessary, connect the negative cable to thebattery, set the power mode to ON. Turn the steering wheel 90° clockwise. Using a plastic trim tool, release the hooks.
7. Turn the steering wheel 180° counterclockwise. Using a plastic trim tool, release the hooks.
UPPER COLUMNCOVER
2 HOOKS PLASTICTRIM TOOL
UPPER COLUMNCOVER
2 HOOKSPLASTICTRIM TOOL
4 of 24 AII02278-0
8. Release the upper column cover and secure the upper column cover to the dashboard with tape.
9. Remove one self-tapping screw from the lower column cover.
TAPE
2 RETAININGTABS
UPPER COLUMNCOVER DASHBOARD
SELF-TAPPINGSCREW
LOWER COLUMNCOVER
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
10. Turn the steering wheel 180° clockwise and removeone self-tapping screw from the lower column cover.
11. If necessary, set the power mode to OFF, then disconnect the negative cable from the battery.
12. Remove the lower column cover.
SELF-TAPPING SCREWLOWER COLUMN
COVER
SELF-TAPPING SCREW
LOWER COLUMNCOVER
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
13. Remove the front bumper:
• Apply tape to the areas shown on each side.
• Wrap a shop towel around the hood latch.
• Remove the front bulkhead cover.
TAPE FRONT BUMPER
HEADLIGHT
HOOD LATCH(Wrap with a shop towel.)
FRONT FENDER
8 CLIPSFRONT BULKHEADCOVER
8 (1510) 5 of 24
www.collegehillshonda.com
• Remove the four self-tapping screws, two bolts,two hex bolts, and seven clips.
• With the help of an assistant, release seven retaining tabs on each side.NOTE: Remove the retaining tabs from the outside in the order shown. Make sure to remove the retaining tabs in the correct orientation.
4 SELF-TAPPINGSCREWS
7 CLIPS 2 HEXBOLTS
2 BOLTS
7 CLIPS
2 HEX BOLTS
BOLT
BOTTOM VIEWBOLT
FRONTBUMPER
3 RETAINING TABS
2
4 RETAINING TABS
1
FRONTBUMPER
Pull.
6 of 24 AII02278-0
• Remove the three clips.
• With the help of an assistant, remove the front bumper. Place the front bumper on a blanket to prevent damage.
3 CLIPS
FRONT BUMPER
4 RETAINING TABS
FRONT BUMPER
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
14. Remove the eight clips from the right front innerfender and pull back the inner fender as shown.
15. Remove eight clips from the left front inner fender and pull back the inner fender as shown.
8 CLIPSFRONT RIGHT TIRE
RIGHT FRONT INNER FENDER(Pull back.)
8 CLIPS
FRONT LEFT TIRE
LEFT FRONT INNER FENDER(Pull back.)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
Installing the Fog Lights
16. Remove four self-tapping screws from the front bumper.
If the vehicle is equipped with a left cap, continue with step 17; otherwise, go to step 21.
With Left Cap
17. Remove the left cover from the front bumper.
FRONT BUMPER(inside)
4 SELF-TAPPING SCREWS
7 RETAINING TABS
FRONT BUMPER(inside)
LEFT COVER
LEFT CAP
8 (1510) 7 of 24
www.collegehillshonda.com
18. Remove the left cap from the front bumper.19. Install the left fog light on the bumper with three self-tapping screws.
FRONT BUMPER (outside)
LEFT CAP(Discard.)2 SELF-TAPPING
SCREWS(Discard.)
3 SELF-TAPPING SCREWS(supplied)
FRONT BUMPER (outside)
LEFT FOG LIGHT
8 of 24 AII02278-0
20. Install the left cover to the front bumper. Go to step 24.
Without Left Cap
21. Remove the left cover from the front bumper.
FRONT BUMPER
LEFT COVER(reused)
7 RETAINING TABS
7 RETAINING TABS
FRONT BUMPER(inside)
LEFT COVER(Discard.)
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
22. Install the left fog light to the front bumper withthree self-tapping screws.
23. Install the left fog light trim.
3 SELF-TAPPING SCREWS(supplied)
FRONT BUMPER (outside)
LEFT FOG LIGHT
FRONT BUMPERLEFT FOG LIGHT
TRIM
7 RETAINING TABS
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
24. Install the left cover or left fog light with four self-tapping screws.
25. Repeat steps 16 through 24 to install the right fog light to the right side of the front bumper.
Routing the Fog Light Harness
26. Remove three bolts, and move the washer tank aside.
FRONT BUMPER(inside)
4 SELF-TAPPING SCREWS (reused)
WASHER TANK
3 BOLTS
HOOK
8 (1510) 9 of 24
www.collegehillshonda.com
27. Route the fog light harness as shown. Remove thetape from the vehicle 1-pin connector and plug the vehicle 1-pin connector into the fog light harness1-pin connector.
With 2.0L Engine
VEHICLE 1-PIN CONNECTOR
FOG LIGHT HARNESS 1-PIN CONNECTOR
FOG LIGHT HARNESS
RIGHT FRONT INNER FENDER
TAPE(Remove.)
10 of 24 AII02278-0
With 1.5L Engine
28. Install the washer tank.
29. Align the green tape on the fog light harness with the washer tank as shown and secure the fog light harness to the vehicle harness with one wire tie.
VEHICLE 1-PIN CONNECTOR
FOG LIGHT HARNESS 1-PIN CONNECTOR
FOG LIGHT HARNESS
RIGHT FRONT INNER FENDER
TAPE(Remove.)
WIRE TIE
WASHER TANK
FOG LIGHT HARNESS
VEHICLE HARNESS
GREEN TAPE
Align.
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
30. Secure the 1-pin connectors and fog light harness tothe vehicle harness with three wire ties.
31. Check the front bumper beam.
VEHICLE HARNESS
FOG LIGHT HARNESS
WIRE TIE
FOG LIGHT HARNESS
VEHICLE HARNESS
VEHICLE PANEL
WIRE TIE 1-PIN CONNECTORS
SECTION VIEW
2 WIRE TIES
FRONT BUMPER BEAMTYPE A
FRONT BUMPER BEAMTYPE B
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
If the vehicle is equipped with the front bumper beam type A, continue with step 32, otherwise, go to step 38.
With Front Bumper Beam Type A
32. Route the fog light harness along the front bumper beam as shown.
33. Secure the three clips on the left fog light harness to the vehicle panel as shown.
FOG LIGHT HARNESS
FRONT BUMPER BEAM
LEFT HEADLIGHT
3 CLIPS
VEHICLE PANEL
8 (1510) 11 of 24
www.collegehillshonda.com
34. Secure the three clips on the right fog light harnessto the vehicle panel as shown.
35. Secure the fog light harness to the front bumper beam with three long wire ties.
RIGHT HEADLIGHT
3 CLIPS
VEHICLE PANEL
3 LONG WIRE TIES
FRONT BUMPER BEAM FOG LIGHT
HARNESS
12 of 24 AII02278-0
36. Join four long wire ties together as shown and secure the fog light harness to the front bumper beam with two joined long wire ties.
FOG LIGHT HARNESS
2 JOINED LONG WIRE TIES
FRONT BUMPER BEAM
2 LONG WIRE TIES(Joined.)
2 JOINED LONG WIRE TIES
SECTION VIEW
FRONT BUMPER BEAM
FRONT
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
37. Secure the fog light harness to the vehicle harnesswith one wire tie. Go to step 43.
With Front Bumper Beam Type B
38. Route the fog light harness along the front bumper beam as shown.
FRONT BUMPER BEAM
FOG LIGHT HARNESS
VEHICLE HARNESS
VEHICLE CLIP
WIRE TIE
FOG LIGHT HARNESS
VEHICLE PANEL
FRONT BUMPER BEAM
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
39. Secure the three clips on the fog light harness to the vehicle panel as shown.
LEFT HEADLIGHT
3 CLIPS
VEHICLE PANEL
8 (1510) 13 of 24
www.collegehillshonda.com
40. Secure three clips on the fog light harness to thevehicle panel as shown.
41. Secure the fog light harness to the front bumper beam with five long wire ties.
RIGHT HEADLIGHT
3 CLIPS
VEHICLE PANEL
FOG LIGHT HARNESS
SECTION VIEW
FRONT BUMPER BEAM
FOG LIGHT HARNESS FRONT
BUMPER BEAM
5 LONG WIRE TIES
FRONT
14 of 24 AII02278-0
42. Secure the fog light harness to the vehicle harness with one wire tie.
If the vehicle is equipped with a 2.0L engine, continue with step 43; otherwise, go to step 45.
With 2.0L Engine
43. Install one wire tie with clip to green tape on the fog light harness, and secure the fog light harness to the resonator.
FRONT BUMPER BEAM FOG LIGHT
HARNESSVEHICLE HARNESS VEHICLE
CLIP
WIRE TIE
RESONATOR
FOG LIGHT HARNESS
WIRE TIE WITH CLIP
WIRE TIE WITH CLIP
GREEN TAPE
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
44. Align the branch of the fog light harness with thevehicle clip and secure the fog light harness to the vehicle harness with one wire tie. Go to step 46.
With 1.5L Engine
45. Align the branch of the fog light harness with the vehicle clip and secure the fog light harness to the vehicle harness with one wire tie.
VEHICLE CLIP
VEHICLE HARNESS
FOG LIGHT HARNESS
BRANCHES
WIRE TIE
VEHICLE CLIP
VEHICLE HARNESS
FOG LIGHT HARNESS
BRANCHES
WIRE TIE
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
46. Remove the vehicle ground bolt. Attach the two fog light harness ground terminals to the vehicle ground terminal and install the vehicle ground bolt.NOTE: Do not put the ground terminal calkings on top of one another.
47. Secure the fog light harness to the vehicle harness with one wire tie.
LEFT FRONT INNER FENDER
VEHICLE GROUND BOLT(reused)
VEHICLE GROUND TERMINAL
2 FOG LIGHT HARNESS GROUND TERMINALS
VEHICLE HARNESS
VEHICLE CLIP
WIRE TIEFOG LIGHT HARNESS
8 (1510) 15 of 24
www.collegehillshonda.com
48. Plug the two fog light harness 2-pin connectors intoeach fog light, and with the help of an assistant, install the front bumper.
Routing the Relay Harness
49. Install the relay into the relay harness relay block.
FRONT BUMPER LEFT FOG LIGHT
RIGHT FOG LIGHT
FOG LIGHT HARNESS 2-PIN CONNECTORS
RELAY
RELAY HARNESS RELAY BLOCK
16 of 24 AII02278-0
If the vehicle is equipped with CVT, continue with step 50; otherwise, go to step 51.
With CVT
50. Plug the relay harness 1-pin connector into the vehicle 1-pin connector. Go to step 52.
With M/T
51. Remove the tape from the vehicle 1-pin connector and plug the relay harness 1-pin connector into the vehicle 1-pin connector.
VEHICLE 1-PIN CONNECTOR
RELAY HARNESS 1-PIN CONNECTOR
RELAY HARNESS
FUSE BOX
VEHICLE 1-PIN CONNECTOR
RELAY HARNESS 1-PIN CONNECTOR
RELAY HARNESS
FUSE BOXTAPE(Remove.)
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
52. Route the switch harness as shown. Attach the wiretie with holder to the relay harness relay block and secure it to the vehicle harness with the wire tie with holder.
VEHICLE HARNESS
RELAY HARNESS RELAY BLOCK
WIRE TIE WITH HOLDER
VEHICLE CLIP
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
If the vehicle is without another accessory harness 4-pin connector, continue with step 54; otherwise, go to step 53.
Without Another Accessory Harness 4-Pin Connector
53. Plug the relay harness 4-pin connector into the fuse box. Go to step 55.
FRONT VIEW
Plug in here.
FUSE BOX
RELAY HARNESS 4-PIN CONNECTOR
8 (1510) 17 of 24
www.collegehillshonda.com
With Another Accessory Harness 4-Pin Connector54. Remove and discard the dummy connector from the other accessory harness 4-pin connector and plug the relay harness 4-pin connector into the other accessory harness 4-pin connector.
RELAY HARNESS 4-PIN CONNECTOR
FUSE BOX
FRONT VIEWDUMMY CONNECTOR(Discard.)
OTHER ACCESSORY HARNESS 4-PIN CONNECTORS
OTHER ACCESSORY HARNESS 4-PIN CONNECTOR
18 of 24 AII02278-0
If the vehicle is equipped with a remote control engine starter and/or wireless charger harness 6-pin connector go to step 56; otherwise continue with step 55.
Without Another Accessory Harness 6-pin Connector
55. Plug the relay harness 6-pin connector into the fuse box. Go to step 57.
RELAY HARNESS 6-PIN CONNECTOR
FUSE BOX
FRONT VIEW
Plug in here.
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
With Remote Control Engine Starter and/or Wireless Charger Harness 6-Pin Connector56. If the remote control engine starter and/or wireless charger harness 6-pin connector is plugged into the vehicle 6-pin connector, plug the relay harness 6-pin connector into the remote control engine starter and/or wireless charger harness 6-pin connector.
FUSE BOX
WITH REMOTE CONTROL ENGINE STARTER OR WIRELESS CHARGER HARNESS 6-PIN CONNECTOR
Plug in here.
RELAY HARNESS 6-PIN CONNECTOR
FUSE BOX
Plug in here.
WITH REMOTE CONTROL ENGINE STARTER AND WIRELESS CHARGER HARNESS 6-PIN CONNECTOR
FRONT VIEW
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
57. Secure the relay harness to the vehicle harness with five wire ties.
If the vehicle is equipped with CVT, continue with step 58; otherwise, go to step 59.
With CVT
58. Secure the 1-pin connectors to the vehicle harness with one wire tie. Go to step 60.
5 WIRE TIESRELAY HARNESS
VEHICLE HARNESS
VEHICLE HARNESS
WIRE TIE1-PIN CONNECTORS
8 (1510) 19 of 24
www.collegehillshonda.com
With M/T59. Secure the 1-pin connectors and relay harness to the vehicle harness with two wire ties.
VEHICLE HARNESS
2 WIRE TIES1-PIN CONNECTORS
RELAY HARNESS
20 of 24 AII02278-0
60. Unplug the vehicle connector from the combination light switch.
61. While pushing the two retaining tabs, slide the combination light switch out and remove it from the steering column. NOTE: Do not pull on the lever when removing the switch.
COMBINATION LIGHT SWITCH(Discard.)
2 RETAINING TABS(Push.)
VEHICLE CONNECTOR
STEERING WHEEL
Do not pull on the lever.
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
62. Install the new combination light switch to thesteering column. NOTE: Do not push on the lever when installing the switch.
63. Plug the vehicle connector into the new combination light switch.
64. Plug the 20 A fuse into the fuse box.
NEW COMBINATION LIGHT SWITCH
2 RETAINING TABS(Push.)
VEHICLE CONNECTOR
STEERING WHEEL
Do not push on the lever.
FUSE BOX
CONNECTING LOCATION
20 A FUSE
FRONT VIEW
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
65. Using isopropyl alcohol on a shop towel, thoroughly clean the driver’s kick panel where the fuse label will attach.
66. Attach the fuse label to the driver’s kick panel.
67. Remove the relay box cover.
Clean with isopropyl alcohol.
FUSE LABEL(20 A OPTION FUSE)
ATTACHING
DRIVER’S KICK PANEL
4 RETAINING TABS
RELAY BOX COVER
RELAY BOX
8 (1510) 21 of 24
www.collegehillshonda.com
68. Using isopropyl alcohol on a shop towel, thoroughlyclean the relay box cover where the fuse label will attach.
69. Using scissors, cut the fuse label and attach the fuse label to the relay box cover.
70. Check that all wire harnesses are routed properly and all connectors are plugged in.
71. Install all removed parts.
72. Connect the negative cable to the battery.
73. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.
Clean with isopropyl alcohol.
FUSE LABEL
ATTACHING
RELAY BOX COVER
2 mm(0.08 in.)
FUSE LABEL
22 of 24 AII02278-0
74. Reset the clock.
75. If necessary restore the systems back to normal operation as described in the service information.
Check the Operation of the Fog Light
76. Turn on the headlights (low beam).
77. Turn on the fog light switch (indicator is on).
78. If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable.
NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather.
QC00130AH
FOG
LIG
HT
SWIT
CH
HEADLIGHT SWITCH
Low HighOFF
OFF -
ON
- - -
- - -
The auto light model is shown.
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Fog Light Aiming Adjustment79. Adjust the fog light:
• Adjust the aim according to your local laws and regulations.
• To adjust, turn the adjustment point in or out until the correct aim is obtained.
BULB REPLACEMENT
1. Release the front inner fender.
PHILLIPS SCREWDRIVER
FOG LIGHT
ADJUSTER
BOLT2 CLIPS
FRONT INNER FENDER(Pull down.)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02278-0
2. Unplug the connector from the fog light.
3. Remove the bulb from the fog light as shown.NOTE: Right fog light bulb turns clockwise.
CONNECTOR
BULB (Turn.)
FOG LIGHT
8 (1510) 23 of 24
www.collegehillshonda.com
4. Install the new bulb.• Use only a genuine Honda halogen light bulb with this Specified Wattage: Rating: 12V 35W H8 Halogen Light Bulb P/N 33165-TL0-003
• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or mild detergent solution.
• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, may annoy oncoming driver’s view.
5. Install all removed parts. Check that the wire harness is not pinched. Be sure to tighten the clips and bolt securely.
6. Check the operation of the fog light; readjust the aim if necessary.
Turn the bulb until it stops.
FOG LIGHT
NEW BULB
NEW BULB
CONNECTOR
24 of 24 AII02278-0
8 (1510) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.top related