6390 angle position sensor (aps) calibration instructions · 6390 angle position sensor (aps)...

www.stryker.com 1

6390 Angle Position Sensor (APS) Calibration Instructions

TOOLS REQUIRED

• StrykerEMSUSBTool • Male-to-MaleUSBCable

• T25TorxDriver • TapeMeasure

PROCEDURE

1. Placethevehicleonalevelsurface.

2. MakesurethatthePower-LOADmainpoweristurnedon.

3. PressandholdthereleaseleveratthefootendofthePower-LOADsystemandpulltoremovethecotfromthe

vehiclepatientcompartment.

Note: The head end LED indicators turn solid green only when the cot is ready to unload.

4. Unloadthecotfromthevehicle:

• For cot models 6500/6506 & 6510/6516:

1. Pressandholdtheextend(+)buttononthecotcontrolswitchtoextendthecotbaseuntilthecotwheels

restontheground.

2. Releasetheextend(+)buttonafterthecotisnolongersupportedbytheliftingarms.Theliftingarmswill

continuemovinguntiltheyhavefullylowered.Do not unlock the cot from Power-LOAD.

• For cot models 6085/6086:

1. Operator1(footend)-Graspthecotframeatthefootend.Squeezeandholdthecotmanualrelease.

2. Operator2(side) -Grasp thebaseframe, liftslightly,and lower thebaseframe to its fullyextended

position.Verifythatthebaseisfullyextended.

3. Operator1(FootEnd)−Releasethecotmanualreleaseto locktheundercarriage intotheextended

position.

4. Pressthedown()buttononthePower-LOADcontrolpaneltolowertheliftingarmsandcot.Do not

unlock the cot from Power-LOAD.

5. UsingaT25Torxdriver,removethetwoscrews(A)thatsecurethecovertotheleftwingassemblytogainaccess

to theUSBport (Figure 1). Save the screwsand

coverforreinstallation.

6. UnscrewthecapthatprotectstheUSBport.

7. Set the laptop with the Stryker EMS USB tool

installedontopofthecotmattressatthefootend

ofthecot.

AFigure 1

6390 Angle Position Sensor (APS) Calibration Instructions

2 www.stryker.com

8. Plugthemale-to-maleUSBcableintotheUSBportandtoanavailableUSBportonthelaptop.

Note: Make sure that the male-to-male USB cable will not get caught on anything while the Power-LOAD

system moves in and out of the vehicle patient compartment.

9. Double-clicktheStryker EMS USB Tool icononyourdesktop.Thetoolsoftwarewillautomaticallydetectthe

Power-LOAD.

10. AftertheStrykerEMSUSBtoolandPower-LOADareconnected,clickAdvanced andthenclickCalibrate APS.

11. IntheEnter Passwordfield,enterStryker1andclickEnter.

12. Loadthecotintothevehicle:

• For cot models 6500/6506 & 6510/6516:

• Pressandholdtheretract(–)buttononthecotcontrolswitchtofullyretractthecotundercarriageuntil

thecotissupported.

• For cot models 6085/6086:

• Presstheup()buttononthePower-LOADcontrolpaneltoraisetheliftingarmstothehighestposition.

Note: The cot legs do not retract.

• Operator1(FootEnd)−Graspthecotframeatthefootend.Squeezeandholdthecotmanualrelease.

• Operator2(Side)−Stabilizethecotbyplacingonehandontheouterrail.Graspthebaseframe.After

thefootendoperatorhassqueezedthecotmanualrelease,retracttheundercarriagewithonehandand

holditinplace.

• Operator 1 (Foot End) - Release the cotmanual release to lock the undercarriage in the retracted

position.Ensurethatthecotmanualreleaseisreleased.If it isnotreleased,thecotbasewillextend

preventingthecotfromlockinginthefastener.

13. Pushthecotintothevehiclepatientcompartmentuntilthefootendcotwheelsareoverthefloorofthevehicle

patientcompartment,butnotinthefullinandlockedposition.

www.stryker.com 3

6390 Angle Position Sensor (APS) Calibration Instructions

Figure 3

14. Using a tape measure, measure the distance from the

bottomofthefootendcotwheeltothefloorwiththecot

wheelfacingthebackofthevehiclepatientcompartment

(Figure2).Makesurethatthedistancebetweenthebottom

ofthefootendcotwheeltotheflooris2in.

• Ifthemeasurementismorethan2in,clickDecrement

(-) on the Connected to Trolley calibration screen

(Figure3).

• Ifthemeasurementislessthan2in,clickIncrement

(+) on the Connected to Trolley calibration screen

(Figure3).

15. Graspthecotframeatthefootendto

pullthecotoutofthevehiclepatient

compartment.

Note: The head end LED indicators

turn solid green only when the cot is

ready to unload.

16. Unload thecot from thevehicle(see

steps3-4onpage1).

17. Load the cot into the vehicle (see

steps12-13onpage2).

18. Repeatsteps12-17until thedistance

between the bottom of the foot end

cotwheeltotheflooris2in.

19. Unplug the male-to-male USB cable

fromthePower-LOADUSBport.

20. Screw theUSB port cap back on to

theUSBport.

21. UsingaT25Torxdriver,reinstallthetwoscrews(removedinstep5)tosecurethecovertotheleftwingassembly.

Note: Make sure that the extruded “U” nut does not rotate clockwise when you tighten the bottom right T25

Torx screw on the left wing assembly cover.

22. Verifyproperoperationoftheproductbeforereturningittoservice.

3800E.CentreAve.,Portage,MI490021-800-327-0770|2014/01

Figure 2

2”

RearDoor