9. exposure assessment - clariant · 9. exposure assessment qualitative csa - skin irritation and...

9. EXPOSURE ASSESSMENT QUALITATIVE CSA - SKIN IRRITATION AND EYE DAMAGE

Worker The human health hazard assessment of alkyl ethersulfates (AES) resulted in the identification of skin and eye irritation as the leading health effect. All alkyl ethersulfates of the category are classified for eye damage (H318/R41) and skin irritation (H315/R38). Specific concentration limits for eye damage were established ≥5 and <10% (irritating to eyes). The generic concentration limit for skin irritants is 10% according to CLP and 20% according to DPD. The available data for this effect do not provide quantitative dose-response information; thus, no short-term local DNELs have been derived for dermal exposure and no quantitative risk assessment was performed. Exposure assessment and risk characterisation are performed on a qualitative basis.

The purpose of a qualitative risk characterization is to assess "the likelihood that effects are avoided when implementing the exposure scenario…" (REACH Annex 1, Section 6.5). This qualitative Chemical Safety Assessment (CSA) approach aims to reduce/avoid contact when there is no basis for setting a DNEL or DMEL for a certain human health adverse effect, i.e. when the available data for this adverse effect do not provide quantitative dose-response information, but there exist toxicity data appropriate to allow a qualitative risk characterization. Implementation of risk management measures (RMMs) and operational conditions (OCs) need to be proportional to the degree of concern for the health hazard presented by the substance. Skin irritation is considered a low hazard while eye damage represents a moderate hazard (ECHA Guidance on information requirements and chemical safety assessment, Part E; November 2012). Thus, alkyl ethersulfates are allocated to the moderate hazard category for a qualitative exposure assessment. Exposures should be controlled to at least the levels that represent an acceptable level of risk, i.e. implementation of the chosen RMMs will ensure that the likelihood of an event occurring due to the hazard of the substance is negligible, and the risk is considered to be controlled to a level of no concern.

As qualitative approach dermal exposure should be minimised by appropriate RMMs. Personal protective equipment (PPE) such as protective clothing, closely fitting goggles and chemical-resistant gloves are required in all parts of the facility where contact with product is possible. Further technical and organisational measures apply, such as good general ventilation, good documentation of substance-handling procedures, training for workers on good practice, good standard of personal hygiene, special procedures for cleaning and maintenance etc. When these RMMs and OCs are applied, the risk for dermal exposure is sufficiently controlled. Where activities may lead to aerosol release (e.g. spraying of concentrated AES), additional skin and eye protection measures such as impervious suits and face shields as well as respiratory protection are required.

Handling and storage risk management measures that are generally identified for skin and eye irritation are given in the table below.

Components of the Qualitative Risk Assessment to prevent skin and eye contact Examples of relevant Precautionary (P) Statements and Response (R) Phrases

Components of the Qualitative Risk Assessment

Prevention: Do not get in eyes, on skin, or on

clothing (P262) Wear protective gloves/protective

clothing/eye protection/face protection (P280)

Avoid contact with skin and eyes (S24/25)

In case of contact with eyes rinse immediately with plenty of water and seek medical advice (S26)

Wear suitable gloves and eye/face protection (S37/39)

Response: IF IN EYES: Rinse cautiously with

water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing (P305 + P351 + P338)

If eye irritation persists: Get medical advice/attention (P337 + P313)

Avoid direct contact with product; Wear protective gloves and suitable eye protection (chemical

goggles) at all times when handling the substance Where activities may lead to aerosol release e.g. spraying of

concentrated AES or handling of concentrated dusty AES, then additional skin and eye protection measures such as impervious suits and face shields as well as respiratory protection are required.

Avoid splashes and spills; Avoidance of contact with contaminated tools and objects; Clean up contamination/spills as soon as they occur; Implementation of basic standards of occupational hygiene; Minimise number of staff exposed; Minimise number of manual phases; Regular cleaning of equipment and work area; Ensure a good standard of general ventilation; Ensure suitable management/supervision is in place to check

that the RMMs in place are being used correctly and OCs followed;

Train staff on good practice to prevent / minimise exposures and to report any eye problems that may develop;

Adopt good standards of personal hygiene.

A review of these RMMs indicates that, if the user complies with the generic statements, workers´ exposure to AES will be negligible and risks due to skin and eye irritation can be considered to be adequately controlled.

General population The general population will not come into contact with the neat substances. According to a voluntary industry program carrying out Human and Environmental Risk Assessments (HERA, 2003) the maximum concentration of AES in consumer products is almost 30%. As described above, skin and eye irritation of AES according to the classification criteria laid down in Regulation (EC) 1272/2008 and Directive 67/548/EEC, respectively are not expected below concentrations of 5%. Eye irritation upon accidental spilling of AES containing products is expected to represent the scenario of concern for the general population. In case the concentration of 5% AES is exceeded within the respective consumer exposure scenario, e.g. during use of hand dish washing products, toilet cleaners or laundry liquids, suited risk management measures are in place to ensure safe use. Suited risk management measures may comprise of increased viscosity of products in order to avoid splashes and spills during handling, the use of completed dosing solutions (including tableting of powders), child-resistant fastenings or further product-integrated measures, like increase of particle size to decrease the inhalable fraction of powders. The listed risk management measures are however not comprehensive and further RMMs suited to minimise dermal exposure may be applied. In addition, products containing higher concentrations of AES are commonly used after dilution in water. Handling of diluted AES however is not of concern regarding skin irritation and eye damage. Skin contact to products containing higher concentrations of AES will in general be limited to short exposure periods before being washed off (e.g. hand dishwashing products). Also co-formulation with other surfactants decreases the irritating potential of surfactants when compared to the neat surfactant. Co-formulation results in a lowered critical micelle concentration and subsequently in formation of micelles what in turn reduces the irritating potential when compared to the neat alkyl ethersulfate. This was reported for various surfactants like alkyl sulfates but also alkyl ethersulfates (Dillarstone & Paye, 1993, Effendy & Maibach, 2006; Paye et al, 2006). The low eye irritating potential of AES containing consumer products is also reflected by the long experience with those products. Although eye irritation may occur upon accidental spilling of AES containing products into the eye, this irritation is generally reversible in nature and thus does not represent a serious hazard to the general population. This is supported by poison control center data evaluated within the HERA report: “…Accidental eye contact with AES containing products will at worst result in a transient irritation which heals within a few days with no irreversible effects to the eye. Nevertheless, in case of such an accident, the eyes should be rinsed immediately with plenty of water.” Thus, the irritating potential of AES in products considered for consumer uses are sufficiently controlled via a

variety of risk management measures and available data proved their efficiency. This conclusion is also supported by the HERA report. Nevertheless, it should be stated to avoid contact with the eyes and to flush eyes with plenty of water in case of accidental spilling. Dillarstone & Paye 1993:

Antagonism in concentrated surfactant systems. Contact Derm. 28, 198 Effendy & Maibach 2006:

Detergents. In Irritant Dermatitis, Chew A-L and Maibach HI, (Eds.), Springer 2006 HERA report 2003:

http://www.heraproject.com/files/1-HH-04-HERA%20AES%20HH%20web%20wd.pdf Paye et al. 2006:

Antagonisms between surfactants: The case of laundry detergents. Tenside Surf. Det. 43, 290-294.

Secondary poisoning: Based on the available information, there is no indication of a bioaccumulation potential and, hence, secondary poisoning is not considered relevant Information on the exposure assessment tool Exposure scenarios 9.1 to 9.x have been calculated using EasyTRA 4.0.0. EasyTRA uses algorithms on the basis of the latest versions of the ECHA REACH Guidance chapters R12 (as of March 2010), R14, R15, and R16 (as of October 2012) and EUSES®. EasyTRA is a graphical user interface which works in compliance with ECETOC® Targeted Risk Assessment 3 (as of July 2012; for detailed information see ECETOC Technical Report No. 114) for the calculation of worker and consumer exposure and complies with EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a for the environmental exposure (see ECHA REACH Guidance chapter R16.6.2 ). Results obtained by EasyTRA are routinely validated against the results obtained by performing the same calculations with the original tools. Details on used Targeted Risk Assessment: Exposure assessment in EasyTRA follows a tiered approach, offering increasingly sophisticated refinements at later tiers to adapt the scenarios to real-life situations. The Tier 1 assessments (reduced number of parameters, conservative results) refer to ECETOC TRA v3, 2012 for the consumer, worker and environmental exposure assessment. The Tier 2 assessments refer to ConsExpo 4.1 model for consumer exposure assessment or EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a for the calculation of environmental exposure (EUSES), including full access to all EUSES parameters as a third step in the refinement. EasyTRA can also perform a qualitative assessment, following ECHA Guidance Part E or externally calculated values can be considered. EasyTRA offers the options to generate user defined spERCs, article and product categories as a first refinement in the exposure calculations, before switching to higher Tier tools. The following modifications are possible for the worker exposure assessment, that are already suggested in the ECETOC TRA guidance document TR114: Factor for Peak exposure, use of the exact concentration instead of ECETOCs category approach, and use of the exact process duration instead of ECETOCs category approach. In addition, the exact value for the effectiveness of specific types of respiratory protection can be entered. Values originate from EU standards DIN EN136, EN140, EN143, EN149, EN12941, EN12942. All deviations require mandatory justifications, which are documented in the CSR to assure full transparency of the calculations and underlying assumptions.

CHEMICAL SAFETY REPORT

2013-04-19 ECPA OWB 2.5 CHEMICAL SAFETY REPORT 49

9.2 Scenario 2: Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1003a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.2 ff. Table 3. Description of ES 2

Free short title Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1003a)

Systematic title based on use descriptor ERC 4; PROC 24A

Name of contributing environmental scenario and corresponding ERC

ERC 4 Industrial use of processing aids

Name(s) of contributing worker scenarios and corresponding PROCs

PROC 24a - High (mechanical) energy work-up of substances bound in materials and/or articles - pt < mp - Low Fugacity

9.2.1 Contributing Scenario (1) controlling environmental exposure for ERC 4

Operational conditions

Annual tonnage 1.00E4 to/year

Daily amount used at site 50 kg/day

Release times per year 220 days/year

Local freshwater dilution factor 10

Local marine water dilution factor 100

Release fraction to air from process 0 %

Release fraction to wastewater from process 5 %

Release fraction to soil from process 0 %

Fraction tonnage to region 100 %

Fraction used at main source 0.110 %

STP yes

River flow rate 18000 m3/day

Municipal sewage treatment plant discharge 2000000 L/day

Risk management measures

SpERC AISE SPERC 5.1a.v1 - AISE - Industrial Use of Me-salts in conversion coating - Nickel

9.2.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 24A (PC 14)

Name of contributing scenario 24a - High (mechanical) energy work-up of substances bound in materials and/or articles - pt < mp - Low Fugacity

Product characteristics

Physical state solid

Concentration in substance 100 %

Fugacity / Dustiness low

Frequency and duration of use

Duration of activity >4 hours (default)

Frequency of use 5 days / week

Human factors not influenced by risk management

Exposed skin surface 1,980 cm2

Other given operational conditions affecting workers exposure

Location indoors

Domain industrial

Technical conditions and measures to control dispersion and exposure

Local exhaust ventilation yes (inhalation 80 %)

Conditions and measures related to personal protection, hygiene and health evaluation

Protective gloves 99 %, burst-time: >4 hours (default) (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Respiratory protection no

9.3 Scenario 3: Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel (AISE-P1003b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters.

An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.3 ff. Table 4. Description of ES 3

Free short title Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel (AISE-P1003b)

STP yes

SpERC AISE SPERC 5.1b.v1 - AISE - Industrial Use of Me-salts in conversion coating - Zinc, Chromium, Copper, Manganese

Location indoors

Domain industrial

9.4 Scenario 4: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting (A.I.S.E. M1) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.4 ff. Table 5. Description of ES 4

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting (A.I.S.E. M1)

Systematic title based on use descriptor ERC 2; PROC 1

ERC 2 Formulation of preparations

PROC 1 - Use in closed process, no likelihood of exposure

Daily amount used at site 1.67E4 kg/day

Release fraction to air from process 0.020 %

Release fraction to wastewater from process 0.010 %

STP yes

SpERC AISE SPERC 2.1.a.v1 - AISE - Formulation of Detergents/Maintenance Products: Granular Detergent -Regular (large scale)

9.4.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 1 (PC 0)

Name of contributing scenario 1 - Use in closed process, no likelihood of exposure

Physical state liquid

Exposed skin surface 240 cm2

Location indoors

Domain industrial

Local exhaust ventilation no

Protective gloves No

9.5 Scenario 5: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting (A.I.S.E. M2) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting.

The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.5 ff. Table 6. Description of ES 5

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting (A.I.S.E. M2)

PROC 2 - Use in closed, continuous process with occasional controlled exposure

STP yes

Name of contributing scenario 2 - Use in closed, continuous process with occasional controlled exposure

Location indoors

Domain industrial

9.6 Scenario 6: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting (A.I.S.E. M3) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.6 ff. Table 7. Description of ES 6

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting (A.I.S.E. M3)

PROC 3 - Use in closed batch process (synthesis or formulation)

STP yes

Name of contributing scenario 3 - Use in closed batch process (synthesis or formulation)

Location indoors

Domain industrial

9.7 Scenario 7: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting (A.I.S.E. M4) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.7 ff.

Table 8. Description of ES 7

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting (A.I.S.E. M4)

PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

STP yes

Name of contributing scenario 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

Location indoors

Domain industrial

9.8 Scenario 8: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting (A.I.S.E. M5) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.8 ff. Table 9. Description of ES 8

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting (A.I.S.E. M5)

PROC 5 - Mixing or blending in batch processes (multistage and/or significant contact)

STP yes

Name of contributing scenario 5 - Mixing or blending in batch processes (multistage and/or significant contact)

Location indoors

Domain industrial

9.9 Scenario 9: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities. (A.I.S.E. M6) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities..

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities. (A.I.S.E. M6)

Systematic title based on use descriptor ERC 2; PROC 8B

PROC 8b - Transfer of chemicals from/to vessels/ large containers at dedicated facilities

STP yes

9.9.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 8B (PC 35)

Name of contributing scenario 8b - Transfer of chemicals from/to vessels/ large containers at dedicated facilities

Location indoors

Domain industrial

9.10 Scenario 10: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting (A.I.S.E. M7) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.10 ff. Table 11. Description of ES 10

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting (A.I.S.E. M7)

PROC 9 - Transfer of chemicals into small containers (dedicated filling line)

STP yes

Name of contributing scenario 9 - Transfer of chemicals into small containers (dedicated filling line)

Location indoors

Domain industrial

9.11 Scenario 11: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting (A.I.S.E. M8) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting.

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting (A.I.S.E. M8)

PROC 14 - Production of preparations or articles by tabletting, compression, extrusion, pelletisation

STP yes

SpERC AISE SPERC 2.1.a.v2 - AISE - Formulation of Granular Detergents/Maintenance Products -Regular & Compact (large scale)

Name of contributing scenario 14 - Production of preparations or articles by tabletting, compression, extrusion, pelletisation

Location indoors

Domain industrial

9.12 Scenario 12: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent (A.I.S.E. M9) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.12 ff. Table 13. Description of ES 12

Free short title Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent (A.I.S.E. M9)

PROC 15 - Use of laboratory reagents in small scale laboratories

STP yes

Name of contributing scenario 15 - Use of laboratory reagents in small scale laboratories

Location indoors

Domain industrial

9.13 Scenario 13: Industrial use of Laundry products Laundry detergent; Automatic process (AISE-P101) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Laundry products Laundry detergent; Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.13 ff. Table 14. Description of ES 13

Free short title Industrial use of Laundry products Laundry detergent; Automatic process (AISE-P101)

STP yes

SpERC AISE SPERC 4.1.v1 - AISE - Industrial Use of Water Borne Processing Aids - no RMM

Duration of activity 480 min/day, duration of activity has been considered linearly (justification: Imported Scenario settings from file: 120619_AISE Industrial use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Location indoors

Domain industrial

9.14 Scenario 14: Industrial use of Laundry products Conditioner (softner/starch); Automatic process (AISE-P104) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Laundry products Conditioner (softner/starch); Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.14 ff. Table 15. Description of ES 14

Free short title Industrial use of Laundry products Conditioner (softner/starch); Automatic process (AISE-P104)

STP yes

Location indoors

Domain industrial

9.15 Scenario 15: Industrial use of Laundry products Laundry aid (gasing); Automatic process (AISE-P107) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Laundry products Laundry aid (gasing); Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.15 ff. Table 16. Description of ES 15

Free short title Industrial use of Laundry products Laundry aid (gasing); Automatic process (AISE-P107)

STP yes

Location indoors

Domain industrial

9.16 Scenario 16: Industrial use of Laundry products Laundry aid (non-gasing); Automatic process (AISE-P110) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Laundry products Laundry aid (non-gasing); Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.16 ff. Table 17. Description of ES 16

Free short title Industrial use of Laundry products Laundry aid (non-gasing); Automatic process (AISE-P110)

STP yes

Location indoors

Domain industrial

9.17 Scenario 17: Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process (AISE-P707a, AISE-P707b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.17 ff. Table 18. Description of ES 17

Free short title Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process (AISE-P707a, AISE-P707b)

ERC 4 Industrial use of processing aids ERC 4 Industrial use of processing aids

PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

STP yes

Location outdoors (30%)

Domain industrial

Location indoors

Domain industrial

9.18 Scenario 18: Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process (AISE-P708a, AISE-P708b)

This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.18 ff. Table 19. Description of ES 18

Free short title Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process (AISE-P708a, AISE-P708b)

PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

STP yes

Domain industrial

Location indoors

Domain industrial

Location indoors

Domain industrial

9.19 Scenario 19: Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P709a, AISE-P709b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.19 ff. Table 20. Description of ES 19

Free short title Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P709a, AISE-P709b)

STP yes

Domain industrial

Location indoors

Domain industrial

Location indoors

Domain industrial

9.20 Scenario 20: Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process (AISE-P710a, AISE-P710b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.20 ff. Table 21. Description of ES 20

Free short title Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process (AISE-P710a, AISE-P710b)

PROC 7 - Industrial spraying PROC 7 - Industrial spraying PROC 7 - Industrial spraying PROC 7 - Industrial spraying

STP yes

Name of contributing scenario 7 - Industrial spraying

Concentration in substance 10 %, concentration has been considered linearly (justification: The concentration is limited to 10%.)

Domain industrial

Protective gloves 99 %, burst-time: 15 mins to 1 hour (justification: Imported Scenario settings from file: 120619_AISE Industrial use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Location indoors

Domain industrial

Location indoors

Domain industrial

9.21 Scenario 21: Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process (AISE-P711a, AISE-P711b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.21 ff. Table 22. Description of ES 21

Free short title Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process (AISE-P711a, AISE-P711b)

Systematic title based on use descriptor ERC 4; PROC 7, 10

PROC 7 - Industrial spraying PROC 10 - Roller application or brushing

STP yes

Domain industrial

Name of contributing scenario 10 - Roller application or brushing

Domain industrial

Protective gloves 99 %, burst-time: >4 hours (default) (justification: Imported Scenario settings from file: 120619_AISE Industrial use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

9.22 Scenario 22: Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P712a, AISE-P712b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.22 ff.

Free short title Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P712a, AISE-P712b)

STP yes

Domain industrial

Location indoors

Domain industrial

Location indoors

Domain industrial

9.23 Scenario 23: Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic (AISE-P713) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.23 ff. Table 24. Description of ES 23

Free short title Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic (AISE-P713)

PROC 10 - Roller application or brushing

STP yes

Domain industrial

9.24 Scenario 24: Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process (AISE-P714a, AISE-P714b)

This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.24 ff. Table 25. Description of ES 24

Free short title Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process (AISE-P714a, AISE-P714b)

PROC 7 - Industrial spraying PROC 10 - Roller application or brushing

STP yes

Domain industrial

9.25 Scenario 25: Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process (AISE-P801) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.25 ff. Table 26. Description of ES 25

Free short title Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process (AISE-P801)

STP yes

Location indoors

Domain industrial

9.26 Scenario 26: Industrial use of Food beverage and pharmacos products

Process cleaner; Semi closed cleaning process (AISE-P802) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Process cleaner; Semi closed cleaning process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.26 ff. Table 27. Description of ES 26

Free short title Industrial use of Food beverage and pharmacos products Process cleaner; Semi closed cleaning process (AISE-P802)

STP yes

Location indoors

Domain industrial

9.27 Scenario 27: Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process (AISE-P803) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.27 ff. Table 28. Description of ES 27

Free short title Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process (AISE-P803)

PROC 7 - Industrial spraying

STP yes

Location indoors

Domain industrial

Respiratory protection 90 %

9.28 Scenario 28: Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process (AISE-P804)

This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.28 ff. Table 29. Description of ES 28

Free short title Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process (AISE-P804)

PROC 13 - Treatment of articles by dipping and pouring

STP yes

Name of contributing scenario 13 - Treatment of articles by dipping and pouring

Location indoors

Domain industrial

9.29 Scenario 29: Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process (AISE-P805) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.29 ff. Table 30. Description of ES 29

Free short title Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process (AISE-P805)

STP yes

Location indoors

Domain industrial

9.30 Scenario 30: Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process (AISE-P806) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into

environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.30 ff. Table 31. Description of ES 30

Free short title Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process (AISE-P806)

STP yes

Location indoors

Domain industrial

9.31 Scenario 31: Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process (AISE-P807) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.31 ff. Table 32. Description of ES 31

Free short title Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process (AISE-P807)

STP yes

Location indoors

Domain industrial

9.32 Scenario 32: Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process (AISE-P809) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure.

The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.32 ff. Table 33. Description of ES 32

Free short title Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process (AISE-P809)

STP yes

Location indoors

Domain industrial

9.33 Scenario 33: Industrial use of pharmacos products Disinfection product; Semi-automatic process (AISE-P810) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of pharmacos products Disinfection product; Semi-automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.33 ff. Table 34. Description of ES 33

Free short title Industrial use of pharmacos products Disinfection product; Semi-automatic process (AISE-P810)

STP yes

Location indoors

Domain industrial

9.34 Scenario 34: Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process (AISE-P811) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process.

Free short title Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process (AISE-P811)

STP yes

Location indoors

Domain industrial

9.35 Scenario 35: Industrial use of Water treatment Products Preservation and sanitation agent ; Process water (AISE-P903) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Water treatment Products Preservation and sanitation agent ; Process water. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.35 ff. Table 36. Description of ES 35

Free short title Industrial use of Water treatment Products Preservation and sanitation agent ; Process water (AISE-P903)

STP yes

Domain industrial

9.36 Scenario 36: Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water (AISE-P904) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.36 ff. Table 37. Description of ES 36

Free short title Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water (AISE-P904)

STP yes

Domain industrial

9.37 Scenario 37: Industrial use of Water treatment Products Sanitation agent; Waste water (AISE-P905) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Water treatment Products Sanitation agent; Waste water. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.37 ff. Table 38. Description of ES 37

Free short title Industrial use of Water treatment Products Sanitation agent; Waste water (AISE-P905)

STP yes

Domain industrial

9.38 Scenario 38: Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P906) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.38 ff. Table 39. Description of ES 38

Free short title Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P906)

STP yes

Domain industrial

9.39 Scenario 39: Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P907) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.39 ff. Table 40. Description of ES 39

Free short title Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P907)

STP yes

Domain industrial

9.40 Scenario 40: Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1001a, AISE-P1001b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.40 ff. Table 41. Description of ES 40

Free short title Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1001a, AISE-P1001b)

PROC 2 - Use in closed, continuous process with occasional controlled exposure PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

STP yes

Location indoors

Domain industrial

Location indoors

Domain industrial

9.41 Scenario 41: Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel (AISE-P1001a, AISE-P1001b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.41 ff. Table 42. Description of ES 41

Free short title Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel (AISE-P1001a, AISE-P1001b)

PROC 2 - Use in closed, continuous process with occasional controlled exposure PROC 4 - Use in batch and other process (synthesis) where opportunity for exposure arises

STP yes

Location indoors

Domain industrial

Location indoors

Domain industrial

9.42 Scenario 42: Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1002a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are

described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.42 ff. Table 43. Description of ES 42

Free short title Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1002a)

PROC 17 - Lubrication at high energy conditions and in partly open process

STP yes

Name of contributing scenario 17 - Lubrication at high energy conditions and in partly open process

Location indoors

Domain industrial

9.43 Scenario 43: Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel (AISE-P1002b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.43 ff. Table 44. Description of ES 43

Free short title Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel (AISE-P1002b)

PROC 17 - Lubrication at high energy conditions and in partly open process

STP yes

Name of contributing scenario 17 - Lubrication at high energy conditions and in partly open process

Location indoors

Domain industrial

9.44 Scenario 44: Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese

(AISE-P1003a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.44 ff. Table 45. Description of ES 44

Free short title Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1003a)

STP yes

Location indoors

Domain industrial

9.45 Scenario 45: Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel (AISE-P1003b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.45 ff. Table 46. Description of ES 45

Free short title Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel (AISE-P1003b)

STP yes

Location indoors

Domain industrial

9.46 Scenario 46: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1004a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure.

The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.46 ff. Table 47. Description of ES 46

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1004a)

STP yes

Location indoors

Domain industrial

9.47 Scenario 47: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel (AISE-P1004b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.47 ff. Table 48. Description of ES 47

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel (AISE-P1004b)

STP yes

Location indoors

Domain industrial

9.48 Scenario 48: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1005a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure.

The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.48 ff. Table 49. Description of ES 48

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1005a)

STP yes

Location indoors

Domain industrial

9.49 Scenario 49: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel (AISE-P1005b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.49 ff. Table 50. Description of ES 49

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel (AISE-P1005b)

STP yes

Location indoors

Domain industrial

9.50 Scenario 50: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1006a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters.

An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.50 ff. Table 51. Description of ES 50

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1006a)

STP yes

Location indoors

Domain industrial

9.51 Scenario 51: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process (AISE-P1006b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.51 ff. Table 52. Description of ES 51

Free short title Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process (AISE-P1006b)

STP yes

Location indoors

Domain industrial

9.52 Scenario 52: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium,

Copper, Manganese (AISE-P1007a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.52 ff. Table 53. Description of ES 52

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1007a)

STP yes

Location indoors

Domain industrial

9.53 Scenario 53: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel (AISE-P1007b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.53 ff. Table 54. Description of ES 53

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel (AISE-P1007b)

STP yes

Location indoors

Domain industrial

9.54 Scenario 54: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1008a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.54 ff. Table 55. Description of ES 54

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1008a)

STP yes

Location indoors

Domain industrial

9.55 Scenario 55: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process (AISE-P1008b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.55 ff. Table 56. Description of ES 55

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process (AISE-P1008b)

STP yes

Location indoors

Domain industrial

9.56 Scenario 56: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1009a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.56 ff. Table 57. Description of ES 56

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1009a)

STP yes

Location indoors

Domain industrial

9.57 Scenario 57: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel (AISE-P1009b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.57 ff. Table 58. Description of ES 57

Free short title Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel (AISE-P1009b)

STP yes

Location indoors

Domain industrial

9.58 Scenario 58: Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1010a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.58 ff. Table 59. Description of ES 58

Free short title Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1010a)

STP yes

Location indoors

Domain industrial

9.59 Scenario 59: Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel (AISE-P1010b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.59 ff. Table 60. Description of ES 59

Free short title Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel (AISE-P1010b)

STP yes

Location indoors

Domain industrial

9.60 Scenario 60: Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1011a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.60 ff. Table 61. Description of ES 60

Free short title Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1011a)

STP yes

Location indoors

Domain industrial

9.61 Scenario 61: Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel (AISE-P1011b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel.

Free short title Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel (AISE-P1011b)

STP yes

Location indoors

Domain industrial

9.62 Scenario 62: Industrial use of Quality control Laboratory Reagents (AISE-P1250) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Industrial use of Quality control Laboratory Reagents. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.62 ff. Table 63. Description of ES 62

Free short title Industrial use of Quality control Laboratory Reagents (AISE-P1250)

STP yes

Location indoors

Domain industrial

9.63 Scenario 63: Professional Use of Laundry products Laundry detergent; Semi automatic process (AISE-P102) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Laundry detergent; Semi automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

scenarios is summarized in chapter 10.63 ff. Table 64. Description of ES 63

Free short title Professional Use of Laundry products Laundry detergent; Semi automatic process (AISE-P102)

Systematic title based on use descriptor ERC 8A; PROC 1

ERC 8a Wide dispersive indoor use of processing aids in open systems

9.63.1 Contributing Scenario (1) controlling environmental exposure for ERC 8A

Daily amount used at site 2.055 kg/day

STP yes

SpERC AISE SPERC 8a.1.a.v1 - AISE - Wide Dispersive Use in ‘Down the Drain’ cleaning and maintenance products (Consumers and Professionals) - Fraction of EU tonnage to region: 0.04 (default: 0.1)

9.63.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 (PC 35)

Location indoors

Domain professional

9.64 Scenario 64: Professional Use of Laundry products Laundry detergent; Manual process (AISE-P103) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Laundry detergent; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.64 ff. Table 65. Description of ES 64

Free short title Professional Use of Laundry products Laundry detergent; Manual process (AISE-P103)

STP yes

Duration of activity 1 - 4 hours

Location indoors

Ventilation good (30%)

Domain professional

9.65 Scenario 65: Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process (AISE-P105) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.65 ff. Table 66. Description of ES 65

Free short title Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process (AISE-P105)

Systematic title based on use descriptor ERC 8A; PROC 1, 8A

PROC 1 - Use in closed process, no likelihood of exposure PROC 8a - Transfer of chemicals from/to vessels/ large containers at non dedicated facilities

STP yes

Location indoors

Domain professional

9.65.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A (PC 35)

Name of contributing scenario 8a - Transfer of chemicals from/to vessels/ large containers at non dedicated facilities

Location indoors

Domain professional

9.66 Scenario 66: Professional Use of Laundry products Laundry aid (gasing); Semi automatic process (AISE-P108) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Laundry aid (gasing); Semi automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.66 ff. Table 67. Description of ES 66

Free short title Professional Use of Laundry products Laundry aid (gasing); Semi automatic process (AISE-P108)

Systematic title based on use descriptor ERC 8B; PROC 1, 8A

ERC 8b Wide dispersive indoor use of reactive substances in open systems

9.66.1 Contributing Scenario (1) controlling environmental exposure for ERC 8B

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.67 Scenario 67: Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process (AISE-P111) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.67 ff. Table 68. Description of ES 67

Free short title Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process (AISE-P111)

Systematic title based on use descriptor ERC 8B; PROC 1, 8A

ERC 8b Wide dispersive indoor use of reactive substances in open systems

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.68 Scenario 68: Professional Use of Laundry products Laundry aid (non-gasing); Manual process (AISE-P112) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Laundry aid (non-gasing); Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.68 ff. Table 69. Description of ES 68

Free short title Professional Use of Laundry products Laundry aid (non-gasing); Manual process (AISE-P112)

STP yes

Location indoors

Domain professional

9.69 Scenario 69: Professional Use of Laundry products Prespotter/Stain remover; Manual process (AISE-P113a, AISE-P113b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Laundry products Prespotter/Stain remover;

Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.69 ff. Table 70. Description of ES 69

Free short title Professional Use of Laundry products Prespotter/Stain remover; Manual process (AISE-P113a, AISE-P113b)

Systematic title based on use descriptor ERC 8A; PROC 11, 10

ERC 8a Wide dispersive indoor use of processing aids in open systems ERC 8a Wide dispersive indoor use of processing aids in open systems

PROC 11 - Non industrial spraying PROC 10 - Roller application or brushing

STP yes

Name of contributing scenario 11 - Non industrial spraying

Duration of activity 15 mins to 1 hour

Location indoors

Domain professional

Location indoors

Domain professional

9.70 Scenario 70: Professional Use of Dishwash products Dishwash product; Manual process (AISE-P201) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Dishwash products Dishwash product; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.70 ff. Table 71. Description of ES 70

Free short title Professional Use of Dishwash products Dishwash product; Manual process (AISE-P201)

STP yes

Location indoors

Domain professional

9.71 Scenario 71: Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process (AISE-P202) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

Free short title Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process (AISE-P202)

STP yes

Location indoors

Domain professional

9.72 Scenario 72: Professional Use of Dishwash products Dishwash product; Semi-Automatic process (AISE-P203) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Dishwash products Dishwash product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.72 ff. Table 73. Description of ES 72

Free short title Professional Use of Dishwash products Dishwash product; Semi-Automatic process (AISE-P203)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.73 Scenario 73: Professional Use of Dishwash products Rinse aid; Semi-Automatic process (AISE-P204) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Dishwash products Rinse aid; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.73 ff. Table 74. Description of ES 73

Free short title Professional Use of Dishwash products Rinse aid; Semi-Automatic process (AISE-P204)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.74 Scenario 74: Professional Use of General surface cleaning products General purpose cleaner; Manual process (AISE-P301) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products General purpose cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.74 ff. Table 75. Description of ES 74

Free short title Professional Use of General surface cleaning products General purpose cleaner; Manual process (AISE-P301)

STP yes

Location indoors

Domain professional

9.75 Scenario 75: Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process (AISE-P302a, AISE-P302b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.75 ff. Table 76. Description of ES 75

Free short title Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process (AISE-P302a, AISE-P302b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.76 Scenario 76: Professional Use of General surface cleaning products Kitchen cleaner; Manual process (AISE-P303) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Kitchen cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.76 ff. Table 77. Description of ES 76

Free short title Professional Use of General surface cleaning products Kitchen cleaner; Manual process (AISE-P303)

STP yes

Location indoors

Domain professional

9.77 Scenario 77: Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process (AISE-P304a, AISE-P304b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.77 ff. Table 78. Description of ES 77

Free short title Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process (AISE-P304a, AISE-P304b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.78 Scenario 78: Professional Use of General surface cleaning products Sanitary cleaner; Manual process (AISE-P305) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Sanitary cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.78 ff. Table 79. Description of ES 78

Free short title Professional Use of General surface cleaning products Sanitary cleaner; Manual process (AISE-P305)

STP yes

Location indoors

Domain professional

9.79 Scenario 79: Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process (AISE-P306a, AISE-P306b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.79 ff. Table 80. Description of ES 79

Free short title Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process (AISE-P306a, AISE-P306b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.80 Scenario 80: Professional Use of General surface cleaning products Descaling agent; Manual process (AISE-P307) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Descaling agent; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.80 ff. Table 81. Description of ES 80

Free short title Professional Use of General surface cleaning products Descaling agent; Manual process (AISE-P307)

STP yes

Location indoors

Domain professional

9.81 Scenario 81: Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process (AISE-P308a, AISE-P308b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.81 ff. Table 82. Description of ES 81

Free short title Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process (AISE-P308a, AISE-P308b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.82 Scenario 82: Professional Use of General surface cleaning products Periodic cleaning by dipping (AISE-P309) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Periodic cleaning by dipping. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.82 ff. Table 83. Description of ES 82

Free short title Professional Use of General surface cleaning products Periodic cleaning by dipping (AISE-P309)

STP yes

Location indoors

Domain professional

9.83 Scenario 83: Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process (AISE-P310) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.83 ff. Table 84. Description of ES 83

Free short title Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process (AISE-P310)

STP yes

Location indoors

Domain professional

9.84 Scenario 84: Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process (AISE-P311a, AISE-P311b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.84 ff. Table 85. Description of ES 84

Free short title Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process (AISE-P311a, AISE-P311b)

PROC 10 - Roller application or brushing PROC 11 - Non industrial spraying

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.85 Scenario 85: Professional Use of General surface cleaning products Glass cleaner; Manual process (AISE-P312) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters.

An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Glass cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.85 ff. Table 86. Description of ES 85

Free short title Professional Use of General surface cleaning products Glass cleaner; Manual process (AISE-P312)

STP yes

Location indoors

Domain professional

9.86 Scenario 86: Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process (AISE-P313a, AISE-P313b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.86 ff. Table 87. Description of ES 86

Free short title Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process (AISE-P313a, AISE-P313b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.87 Scenario 87: Professional Use of General surface cleaning products Surface disinfectant; Manual process (AISE-P314) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure.

The following scenarios contribute to the scenario Professional Use of General surface cleaning products Surface disinfectant; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.87 ff. Table 88. Description of ES 87

Free short title Professional Use of General surface cleaning products Surface disinfectant; Manual process (AISE-P314)

STP yes

Location indoors

Domain professional

9.88 Scenario 88: Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process (AISE-P315a, AISE-P315b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.88 ff. Table 89. Description of ES 88

Free short title Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process (AISE-P315a, AISE-P315b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.89 Scenario 89: Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process (AISE-P316) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into

environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.89 ff. Table 90. Description of ES 89

Free short title Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process (AISE-P316)

STP yes

Location indoors

Domain professional

9.90 Scenario 90: Professional Use of General surface cleaning products Wet wipes; Manual process (AISE-P317) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of General surface cleaning products Wet wipes; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.90 ff. Table 91. Description of ES 90

Free short title Professional Use of General surface cleaning products Wet wipes; Manual process (AISE-P317)

STP yes

Location indoors

Domain professional

9.91 Scenario 91: Professional Use of Floor care products Floor cleaner; Semi-Automatic process (AISE-P401) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Floor cleaner; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.91 ff.

Free short title Professional Use of Floor care products Floor cleaner; Semi-Automatic process (AISE-P401)

STP yes

Location indoors

Domain professional

9.92 Scenario 92: Professional Use of Floor care products Floor cleaner; Spray and wipe manual process (AISE-P402a, AISE-P402b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Floor cleaner; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.92 ff. Table 93. Description of ES 92

Free short title Professional Use of Floor care products Floor cleaner; Spray and wipe manual process (AISE-P402a, AISE-P402b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.93 Scenario 93: Professional Use of Floor care products Floor cleaner; Manual process (AISE-P403a, AISE-P403b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Floor cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.93 ff. Table 94. Description of ES 93

Free short title Professional Use of Floor care products Floor cleaner; Manual process (AISE-P403a, AISE-P403b)

PROC 10 - Roller application or brushing PROC 10 - Roller application or brushing

STP yes

Domain professional

Location indoors

Domain professional

9.94 Scenario 94: Professional Use of Floor care products Floor stripper; Manual process (AISE-P404) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Floor stripper; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.94 ff. Table 95. Description of ES 94

Free short title Professional Use of Floor care products Floor stripper; Manual process (AISE-P404)

STP yes

Location indoors

Domain professional

9.95 Scenario 95: Professional Use of Floor care products Floor stripper; Semi-Automatic process (AISE-P405) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Floor stripper; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.95 ff. Table 96. Description of ES 95

Free short title Professional Use of Floor care products Floor stripper; Semi-Automatic process (AISE-P405)

STP yes

Location indoors

Domain professional

9.96 Scenario 96: Professional Use of Floor care products Polish / impregnating agent; Manual process (AISE-P406) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Polish / impregnating agent; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.96 ff. Table 97. Description of ES 96

Free short title Professional Use of Floor care products Polish / impregnating agent; Manual process (AISE-P406)

STP yes

Location indoors

Domain professional

9.97 Scenario 97: Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process (AISE-P407) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.97 ff. Table 98. Description of ES 97

Free short title Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process (AISE-P407)

STP yes

Location indoors

Domain professional

9.98 Scenario 98: Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process (AISE-P408a, AISE-P408b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.98 ff. Table 99. Description of ES 98

Free short title Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process (AISE-P408a, AISE-P408b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.99 Scenario 99: Professional Use of Floor care products Carpet cleaner; Manual process (AISE-P409) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Carpet cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.99 ff. Table 100. Description of ES 99

Free short title Professional Use of Floor care products Carpet cleaner; Manual process (AISE-P409)

STP yes

Location indoors

Domain professional

9.100 Scenario 100: Professional Use of Floor care products Carpet cleaner; Semi-Automatic process (AISE-P410) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Carpet cleaner; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.100 ff. Table 101. Description of ES 100

Free short title Professional Use of Floor care products Carpet cleaner; Semi-Automatic process (AISE-P410)

STP yes

Location indoors

Domain professional

9.101 Scenario 101: Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process (AISE-P411a, AISE-P411b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.101 ff. Table 102. Description of ES 101

Free short title Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process (AISE-P411a, AISE-P411b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.102 Scenario 102: Professional Use of Maintenance Products Wooden Furniture care product; Manual process (AISE-P601) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Wooden Furniture care product; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.102 ff. Table 103. Description of ES 102

Free short title Professional Use of Maintenance Products Wooden Furniture care product; Manual process (AISE-P601)

STP yes

Location indoors

Domain professional

9.103 Scenario 103: Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process (AISE-P602a, AISE-P602b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.103 ff. Table 104. Description of ES 103

Free short title Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process (AISE-P602a, AISE-P602b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.104 Scenario 104: Professional Use of Maintenance Products Leather care

product; Manual process (AISE-P603) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Leather care product; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.104 ff. Table 105. Description of ES 104

Free short title Professional Use of Maintenance Products Leather care product; Manual process (AISE-P603)

STP yes

Location indoors

Domain professional

9.105 Scenario 105: Professional Use of Maintenance Products Leather care product; Spray and wipe manual process (AISE-P604a, AISE-P604b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Leather care product; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.105 ff. Table 106. Description of ES 105

Free short title Professional Use of Maintenance Products Leather care product; Spray and wipe manual process (AISE-P604a, AISE-P604b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.106 Scenario 106: Professional Use of Maintenance Products Leather care product; Semi-Automatic process (AISE-P605)

This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Leather care product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.106 ff. Table 107. Description of ES 106

Free short title Professional Use of Maintenance Products Leather care product; Semi-Automatic process (AISE-P605)

STP yes

Location indoors

Domain professional

9.107 Scenario 107: Professional Use of Maintenance Products Drain unblocker; Manual process (AISE-P606) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Drain unblocker; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.107 ff. Table 108. Description of ES 107

Free short title Professional Use of Maintenance Products Drain unblocker; Manual process (AISE-P606)

STP yes

Location indoors

Domain professional

9.108 Scenario 108: Professional Use of Maintenance Products Drain cleaner; Manual process (AISE-P607) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Drain cleaner; Manual

process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.108 ff. Table 109. Description of ES 108

Free short title Professional Use of Maintenance Products Drain cleaner; Manual process (AISE-P607)

STP yes

Location indoors

Domain professional

9.109 Scenario 109: Professional Use of Maintenance Products Stainless steel care ; Manual process (AISE-P608) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Stainless steel care ; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.109 ff. Table 110. Description of ES 109

Free short title Professional Use of Maintenance Products Stainless steel care ; Manual process (AISE-P608)

STP yes

Location indoors

Domain professional

9.110 Scenario 110: Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process (AISE-P609a, AISE-P609b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.110 ff. Table 111. Description of ES 110

Free short title Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process (AISE-P609a, AISE-P609b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.111 Scenario 111: Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P701a, AISE-P701b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.111 ff. Table 112. Description of ES 111

Free short title Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P701a, AISE-P701b)

STP yes

Domain professional

Location indoors

Domain professional

9.112 Scenario 112: Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process (AISE-P702a, AISE-P702b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

Free short title Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process (AISE-P702a, AISE-P702b)

PROC 11 - Non industrial spraying PROC 11 - Non industrial spraying

STP yes

Domain professional

Location indoors

Domain professional

9.113 Scenario 113: Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process (AISE-P703a, AISE-P703b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.113 ff. Table 114. Description of ES 113

Free short title Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process (AISE-P703a, AISE-P703b)

STP yes

Domain professional

9.114 Scenario 114: Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P704a, AISE-P704b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

Free short title Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P704a, AISE-P704b)

STP yes

Domain professional

Location indoors

Domain professional

9.115 Scenario 115: Professional Use of Vehicle cleaning Products Boat cleaner; Manual process (AISE-P705) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Boat cleaner; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.115 ff. Table 116. Description of ES 115

Free short title Professional Use of Vehicle cleaning Products Boat cleaner; Manual process (AISE-P705)

STP yes

Domain professional

9.116 Scenario 116: Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process (AISE-P706a, AISE-P706b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.116 ff. Table 117. Description of ES 116

Free short title Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process (AISE-P706a, AISE-P706b)

STP yes

Domain professional

9.117 Scenario 117: Professional Use of pharmacos products Animal care; Manual process (AISE-P808) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of pharmacos products Animal care; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.117 ff. Table 118. Description of ES 117

Free short title Professional Use of pharmacos products Animal care; Manual process (AISE-P808)

STP yes

Location indoors

Domain professional

9.118 Scenario 118: Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P901a, AISE-P901b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.118 ff. Table 119. Description of ES 118

Free short title Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P901a, AISE-P901b)

Systematic title based on use descriptor ERC 8D; PROC 11

ERC 8d Wide dispersive outdoor use of processing aids in open systems ERC 8d Wide dispersive outdoor use of processing aids in open systems

9.118.1 Contributing Scenario (1) controlling environmental exposure for ERC 8D

STP yes

Domain professional

Location indoors

Domain professional

9.119 Scenario 119: Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P902a, AISE-P902b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.119 ff. Table 120. Description of ES 119

Free short title Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P902a, AISE-P902b)

Systematic title based on use descriptor ERC 8D; PROC 11, 10

ERC 8d Wide dispersive outdoor use of processing aids in open systems ERC 8d Wide dispersive outdoor use of processing aids in open systems

PROC 11 - Non industrial spraying PROC 11 - Non industrial spraying PROC 10 - Roller application or brushing PROC 10 - Roller application or brushing

STP yes

Domain professional

Location indoors

Domain professional

Location indoors

Domain professional

9.120 Scenario 120: Professional Use of Medical Devices Medical devices ; Semi-automatic process (AISE-P1101) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into

environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Medical Devices Medical devices ; Semi-automatic process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.120 ff. Table 121. Description of ES 120

Free short title Professional Use of Medical Devices Medical devices ; Semi-automatic process (AISE-P1101)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.121 Scenario 121: Professional Use of Medical Devices Medical devices ; Dipping process (AISE-P1102) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Medical Devices Medical devices ; Dipping

process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.121 ff. Table 122. Description of ES 121

Free short title Professional Use of Medical Devices Medical devices ; Dipping process (AISE-P1102)

STP yes

Location indoors

Domain professional

9.122 Scenario 122: Professional Use of Medical Devices Medical devices ; Manual process (AISE-P1103) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Medical Devices Medical devices ; Manual process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.122 ff. Table 123. Description of ES 122

Free short title Professional Use of Medical Devices Medical devices ; Manual process (AISE-P1103)

STP yes

Location indoors

Domain professional

9.123 Scenario 123: Professional Use of Medical Devices Medical devices ; Spray and wipe process (AISE-P1104a, AISE-P1104b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Medical Devices Medical devices ; Spray and wipe process. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.123 ff. Table 124. Description of ES 123

Free short title Professional Use of Medical Devices Medical devices ; Spray and wipe process (AISE-P1104a, AISE-P1104b)

STP yes

Location indoors

Domain professional

Location indoors

Domain professional

9.124 Scenario 124: Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…) (AISE-P1200) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.124 ff. Table 125. Description of ES 124

Free short title Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…) (AISE-P1200)

STP yes

Location indoors

Domain professional

9.125 Scenario 125: Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants (AISE-P1300) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.125 ff. Table 126. Description of ES 125

Free short title Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants (AISE-P1300)

PROC 19 - Hand-mixing with intimate contact (only PPE available

STP yes

Name of contributing scenario 19 - Hand-mixing with intimate contact (only PPE available

Location indoors

Domain professional

9.126 Scenario 126: Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) (AISE_CSP01a, AISE_CSP01b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.126 ff. Table 127. Description of ES 126

Free short title Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) (AISE_CSP01a, AISE_CSP01b)

Systematic title based on use descriptor ERC 8A; PROC 8A

PROC 8a - Transfer of chemicals from/to vessels/ large containers at non dedicated facilities PROC 8a - Transfer of chemicals from/to vessels/ large containers at non dedicated facilities

STP yes

Duration of activity 50 min/day, duration of activity has been considered linearly (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Domain professional

Protective gloves 99 %, burst-time: 15 mins to 1 hour (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Location indoors

Domain professional

9.127 Scenario 127: Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment (AISE_CSP02) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters.

An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.127 ff. Table 128. Description of ES 127

Free short title Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment (AISE_CSP02)

Systematic title based on use descriptor ERC 8A; PROC 8B

PROC 8b - Transfer of chemicals from/to vessels/ large containers at dedicated facilities

STP yes

9.127.2 Contributing Scenario (2) controlling professional worker exposure for PROC 8B (PC 35)

Location indoors

Domain professional

9.128 Scenario 128: Trigger spraying of a professional cleaning or maintenance product during short time. (AISE_CSP03) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Trigger spraying of a professional cleaning or maintenance product during short time.. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.128 ff. Table 129. Description of ES 128

Free short title Trigger spraying of a professional cleaning or maintenance product during short time. (AISE_CSP03)

PROC 11 - Non industrial spraying

STP yes

Location indoors

Domain professional

9.129 Scenario 129: Spraying of a professional cleaning or maintenance product (indoor and outdoor) (AISE_CSP04)

This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Spraying of a professional cleaning or maintenance product (indoor and outdoor). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.129 ff. Table 130. Description of ES 129

Free short title Spraying of a professional cleaning or maintenance product (indoor and outdoor) (AISE_CSP04)

STP yes

Domain professional

Location indoors

Domain professional

9.130 Scenario 130: Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment (AISE_CSP05) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.130 ff. Table 131. Description of ES 130

Free short title Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment (AISE_CSP05)

STP yes

Location indoors

Domain professional

9.131 Scenario 131: Using a diluted professional cleaning solution in a semi closed cleaning equipment (AISE_CSP06) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted professional cleaning solution in a semi closed cleaning equipment. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.131 ff. Table 132. Description of ES 131

Free short title Using a diluted professional cleaning solution in a semi closed cleaning equipment (AISE_CSP06)

STP yes

Location indoors

Domain professional

9.132 Scenario 132: Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure arises (AISE_CSP07) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure arises. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.132 ff. Table 133. Description of ES 132

Free short title Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure arises (AISE_CSP07)

STP yes

Location indoors

Domain professional

9.133 Scenario 133: Brushing a diluted professional cleaning solution, desinfectant or maintenance product (AISE_CSP08) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Brushing a diluted professional cleaning solution, desinfectant or maintenance product. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.133 ff. Table 134. Description of ES 133

Free short title Brushing a diluted professional cleaning solution, desinfectant or maintenance product (AISE_CSP08)

STP yes

Location indoors

Domain professional

9.134 Scenario 134: Brushing a professional cleaning or maintenance product after trigger spraying (AISE_CSP09) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Brushing a professional cleaning or maintenance product after trigger spraying. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.134 ff. Table 135. Description of ES 134

Free short title Brushing a professional cleaning or maintenance product after trigger spraying (AISE_CSP09)

STP yes

Location indoors

Domain professional

9.135 Scenario 135: Brushing a concentrated professional cleaning or maintenance product. (AISE-CSP10) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Brushing a concentrated professional cleaning or maintenance product.. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.135 ff. Table 136. Description of ES 135

Free short title Brushing a concentrated professional cleaning or maintenance product. (AISE-CSP10)

STP yes

Location indoors

Domain professional

Protective gloves 99 %, burst-time: 1 - 4 hours (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

9.136 Scenario 136: Treatment of articles by dipping or pouring with a professional cleaning or maintenance products (AISE_CSP11) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Treatment of articles by dipping or pouring with a professional cleaning or maintenance products. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.136 ff. Table 137. Description of ES 136

Free short title Treatment of articles by dipping or pouring with a professional cleaning or maintenance products (AISE_CSP11)

STP yes

Location indoors

Domain professional

Protective gloves 99 %, burst-time: 1 - 4 hours (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

9.137 Scenario 137: Professional Use of Drain Unblockers (AISE_CSP12) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Professional Use of Drain Unblockers. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.137 ff. Table 138. Description of ES 137

Free short title Professional Use of Drain Unblockers (AISE_CSP12)

STP yes

Location indoors

Domain professional

Protective gloves 99 %, burst-time: less than 15 mins (justification: Imported Scenario settings from file: 120619_AISE Institutional use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

9.138 Scenario 138: Laboratory use of Cleaning and Maintenance products (AISE_CSP13) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Laboratory use of Cleaning and Maintenance products. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.138 ff. Table 139. Description of ES 138

Free short title Laboratory use of Cleaning and Maintenance products (AISE_CSP13)

STP yes

Location indoors

Domain professional

9.139 Scenario 139: Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use (AISE C1) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.139 ff. Table 140. Description of ES 139

Free short title Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use (AISE C1)

Systematic title based on use descriptor ERC 8A; PC 35

Name(s) of contributing consumer scenarios and corresponding PCs/ACs

PC 35 Washing and Cleaning Products (including solvent based products)

STP yes

9.139.2 Contributing Scenario (2) controlling consumer exposure for PC 35

Name of contributing scenario PC 35 Washing and Cleaning Products (including solvent based products)

Calculation model Ecetoc TRA

Product subcategory Laundry and dish washing products

Frequency of use 260 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (5 times per week))

Exposure time 1 h

Spray application no

Product ingredient fraction by weight (inhalation) 60 %

Product ingredient fraction by weight (dermal) 60 %

Amounts used

Amounts used 50 g

Skin surface area dermal hands

Skin surface area oral -

Tranfer factor dermal 100 %

Other given operational conditions affecting consumers exposure

Room volume 20 m3

Release fraction to air 10.0 %

Duration of task shortened compared to ecetocTRA

inhalation: 80 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (10 minutes/task). EcetocTRA uses 60 minutes (estimated for dish washing).)

9.140 Scenario 140: Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use (AISE C2) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.140 ff. Table 141. Description of ES 140

Free short title Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use (AISE C2)

STP yes

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

9.141 Scenario 141: Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use (AISE C3) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

Free short title Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use (AISE C3)

STP yes

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

9.142 Scenario 142: Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use (AISE C4) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.142 ff. Table 143. Description of ES 142

Free short title Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use (AISE C4)

Systematic title based on use descriptor ERC 8A, 8B; PC 35

ERC 8a Wide dispersive indoor use of processing aids in open systems ERC 8b Wide dispersive indoor use of reactive substances in open systems

STP yes

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

9.143 Scenario 143: Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use (AISE C5) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.143 ff. Table 144. Description of ES 143

Free short title Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use (AISE C5)

STP yes

Frequency of use 1 time(s)/day

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

Amount per task decreased compared to ecetocTRA

inhalation: 80 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (10 g/task). EcetocTRA uses 50g (estimated for laundry washing products).)

9.144 Scenario 144: Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use (AISE C6) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.144 ff. Table 145. Description of ES 144

Free short title Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use (AISE C6)

STP yes

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

inhalation: 98 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (<1 minute/task). EcetocTRA uses 60 minutes (estimated for hand dish washing).)

9.145 Scenario 145: Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use (AISE C7) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing

Free short title Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use (AISE C7)

STP yes

Product subcategory Cleaners, liquids (all purpose cleaners, etc.)

Exposure time 0.330 h

Amounts used

Amounts used 250 g

Room volume 20 m3

inhalation: 75 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (60 g/task). EcetocTRA uses 250 grams.)

9.146 Scenario 146: Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use (AISE C8) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.146 ff. Table 147. Description of ES 146

Free short title Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use (AISE C8)

Systematic title based on use descriptor ERC 8A, 8B; PC 35

ERC 8a Wide dispersive indoor use of processing aids in open systems ERC 8b Wide dispersive indoor use of reactive substances in open systems

STP yes

Frequency of use 52 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (1 time per week))

Amounts used

Amounts used 250 g

Room volume 20 m3

Gram per task decreased compared to ecetocTRA inhalation: 85 % (justification: Maximum typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (35 g/task). EcetocTRA uses 250 grams.)

9.147 Scenario 147: Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use (AISE C9) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.147 ff. Table 148. Description of ES 147

Free short title Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use (AISE C9)

STP yes

Amounts used

Amounts used 250 g

Room volume 20 m3

Duration of task decreased compared to ecetocTRA

inhalation: 95 % (justification: Maximum typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (1 minute/task). EcetocTRA uses 20 mins(estimated for surface cleaners).)

9.148 Scenario 148: Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use (AISE C10) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.148 ff. Table 149. Description of ES 148

Free short title Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use (AISE C10)

STP yes

Frequency of use 26 times/year (justification: ConsExpo assumption (26 times per year))

Amounts used

Amounts used 250 g

Room volume 20 m3

Grams per task decreased compared to ecetocTRA

inhalation: 75 % (justification: Maximum typical value from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. for cleaners is 60g/event. This value is used to represent the oven cleaner. EcetocTRA uses 250 grams/event.)

9.149 Scenario 149: Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use (AISE C11) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.149 ff. Table 150. Description of ES 149

Free short title Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use (AISE C11)

STP yes

Frequency of use 10 times/year (justification: ConsExpo Assumption (Carpet spray spot remover; foam) (10 times per year))

Amounts used

Amounts used 250 g

Room volume 20 m3

9.150 Scenario 150: Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use (AISE C12) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.150 ff. Table 151. Description of ES 150

Free short title Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use (AISE C12)

STP yes

Frequency of use 104 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (twice per week).)

Exposure time 1 h

Amounts used

Amounts used 50 g

Room volume 20 m3

inhalation: 80 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (10 g/task). EcetocTRA default: 50g)

9.151 Scenario 151: Consumer use of washing and cleaning products DRAIN PRODUCTS (powder, gel) (AISE C13) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products DRAIN PRODUCTS

(powder, gel). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.151 ff. Table 152. Description of ES 151

Free short title Consumer use of washing and cleaning products DRAIN PRODUCTS (powder, gel) (AISE C13)

STP yes

Frequency of use 52 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (1 time per week))

Amounts used

Amounts used 250 g

Room volume 20 m3

Amount per task and duration of task decreased compared to ecetocTRA

inhalation: 95 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (70 g/event and duration of task: 10 mins). EcetocTRA default: 250g/event and 20 min))

9.152 Scenario 152: Consumer use of washing and cleaning products DESCALERS (AISE C14) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products DESCALERS. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.152 ff. Table 153. Description of ES 152

Free short title Consumer use of washing and cleaning products DESCALERS (AISE C14)

STP yes

Frequency of use 52 times/year (justification: No default values from AISE or RIVM (CONSEXPO) are available. However, it is expected that the frequency of use of descalers will be maximum once per week.)

Amounts used

Amounts used 250 g

Room volume 20 m3

Duration of exposure was decreased compared to ecetocTRA

inhalation: 90 % (justification: No default values from AISE or RIVM (CONSEXPO) are available. However, it is expected that descalers will be applied to a household machine. After a given soaking time the descaler is removed. Thus, exposure duration will be limited to filling and de-filling operations. According to the “Table of habits and practices for consumer products in Western Europe” prepared by A.I.S.E. filling operations of machines take less than 1 minute. It is assumed that filling and de-filling operation will need equal times and thus a exposure time of 2 minutes was applied (EcetocTRA default: 20 min).)

9.153 Scenario 153: Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use (AISE C15) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.153 ff. Table 154. Description of ES 153

Free short title Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use (AISE C15)

STP yes

Amounts used

Amounts used 250 g

Room volume 20 m3

Amount per task and duration reduced compared to ecetocTRA

inhalation: 97.5 % (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (26 g/event and duration of task: 5 mins). EcetocTRA default: 250g/event and 20 min))

9.154 Scenario 154: Consumer use of washing and cleaning products High Pressure washers/cleaners (AISE C21) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure.

The following scenarios contribute to the scenario Consumer use of washing and cleaning products High Pressure washers/cleaners. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.154 ff. Table 155. Description of ES 154

Free short title Consumer use of washing and cleaning products High Pressure washers/cleaners (AISE C21)

STP yes

Frequency of use 12 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (0.23 time per week))

Amounts used

Amounts used 250 g

Room volume 20 m3

9.155 Scenario 155: Consumer use of washing and cleaning products Automotive Care (spray, liquid) (AISE C22) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of washing and cleaning products Automotive Care (spray, liquid). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.155 ff. Table 156. Description of ES 155

Free short title Consumer use of washing and cleaning products Automotive Care (spray, liquid) (AISE C22)

STP yes

Frequency of use 26 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (0.5 time per week))

Amounts used

Amounts used 250 g

Room volume 20 m3

9.156 Scenario 156: AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use (AISE C17) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters.

An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.156 ff. Table 157. Description of ES 156

Free short title AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use (AISE C17)

PC 3 Air care products

STP yes

SpERC AISE SPERC 8a.1.c.v1 - AISE- Wide Dispersive Use in Aerosol products for cleaning and maintenance products (Propellants) Fraction of EU tonnage to region: 0.04 (default: 0.1)

Name of contributing scenario PC 3 Air care products

Product subcategory Aircare, Instant action (aerosol sprays)

Frequency of use 416 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (8 events per week).)

Product ingredient fraction by weight (inhalation) 7.5 %

Amounts used

Amounts used 10 g

Skin surface area dermal -

Room volume 20 m3

9.157 Scenario 157: AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use (AISE C18) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.157 ff. Table 158. Description of ES 157

Free short title AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use (AISE C18)

PC 3 Air care products

STP yes

SpERC AISE SPERC 8a.1.b.v1 - AISE- Wide Dispersive Use in Aerosol products for cleaning and maintenance products (Non-Propellants) Fraction of EU tonnage to region: 0.04 (default: 0.1)

Name of contributing scenario PC 3 Air care products

Product subcategory Aircare, Continuous action (solid & liquid)

Exposure time 8 h

Amounts used

Amounts used 50 g

Skin surface area dermal fingertips

Room volume 20 m3

Prodcut amount per event decreased compared to ecetocTRA

inhalation: 95 % (justification: Using the typical discharge rate (g/s) from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (0.000029 g/s), a maximum amount of 2.5 g will be released during a whole day. EcetocTRA uses 50 g/d as default.)

9.158 Scenario 158: Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants (AISE C19a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.158 ff. Table 159. Description of ES 158

Free short title Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants (AISE C19a)

STP yes

Amounts used

Amounts used 250 g

Room volume 20 m3

Grams/task and duration of task reduced compared to ecetocTRA

inhalation: 98 % (justification: Maximum typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (10.1 g/day and 8.1 min/task). EcetocTRA uses 250g/Task and 20 min/task.)

9.159 Scenario 159: Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants (AISE C19b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.159 ff.

Free short title Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants (AISE C19b)

STP yes

Amounts used

Amounts used 250 g

Room volume 20 m3

Grams per task and duration of task reduced compared to ecetocTRA

inhalation: 98 % (justification: Maximum typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (10.1 g/day and 8.1 min/task). EcetocTRA uses 250g/Task and 20 min/task.)

9.160 Scenario 160: Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants (AISE C20a) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.160 ff. Table 161. Description of ES 160

Free short title Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants (AISE C20a)

PC 31 Polishes and Wax Blends

STP yes

Name of contributing scenario PC 31 Polishes and Wax Blends

Product subcategory Polishes spray (furniture, shoes)

Frequency of use 52 times/year (justification: Typical value taken from “Table of habits and practices for consumer products in Western Europe” by A.I.S.E. (Once per week).)

Exposure time 4 h

Amounts used

Amounts used 135 g

Room volume 20 m3

9.161 Scenario 161: Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants (AISE C20b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants.

Free short title Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants (AISE C20b)

PC 31 Polishes and Wax Blends

STP yes

Name of contributing scenario PC 31 Polishes and Wax Blends

Product subcategory Polishes, wax / cream (floor, furniture, shoes)

Frequency of use 12 times/year (justification: Default values for this scenario in ecetocTRA are 550 g/event, 4h/event and a frequency of once per day. In case e.g. the amount of 550 g is used to wax the floor (during 4h) it is not very likely that the consumer will do this daily but rather once in a month. In case of polishing furnitures or shoes it can be expected that this will take less time and less amount of polish/wax is needed. Following assumptions were made: Waxing/polishing of furniture is done once per week with 100 g for 2 h. Waxing/polishing of shoes is done twice/week with 10 g for 0.5 h. Data of the worst case were calculated and presented.)

Exposure time 4 h

Amounts used

Amounts used 550 g

Room volume 20 m3

9.162 Scenario 162: Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) (AISE_CS_I01a, AISE_CS_I01b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.162 ff. Table 163. Description of ES 162

Free short title Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) (AISE_CS_I01a, AISE_CS_I01b)

Systematic title based on use descriptor ERC 4; PROC 8B

PROC 8b - Transfer of chemicals from/to vessels/ large containers at dedicated facilities PROC 8b - Transfer of chemicals from/to vessels/ large containers at dedicated facilities

STP yes

Domain industrial

Protective gloves 99 %, burst-time: 1 - 4 hours (justification: Imported Scenario settings from file: 120619_AISE Industrial use mapping_Publishedv2 Stand 19.6.2012 Angepasst an EasyTRA.xls)

Location indoors

Domain industrial

9.163 Scenario 163: Using a diluted industrial cleaning solution in a closed cleaning equipment (AISE_CS_I02) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted industrial cleaning solution in a closed cleaning equipment. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.163 ff. Table 164. Description of ES 163

Free short title Using a diluted industrial cleaning solution in a closed cleaning equipment (AISE_CS_I02)

STP yes

Location indoors

Domain industrial

9.164 Scenario 164: Using a diluted industrial cleaning solution in a semi closed cleaning equipment (AISE_CS_I03) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted industrial cleaning solution in a semi closed cleaning equipment. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.164 ff. Table 165. Description of ES 164

Free short title Using a diluted industrial cleaning solution in a semi closed cleaning equipment (AISE_CS_I03)

STP yes

Location indoors

Domain industrial

9.165 Scenario 165: Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises (AISE_CS_I04a, AISE_CS_I04b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.165 ff. Table 166. Description of ES 165

Free short title Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises (AISE_CS_I04a, AISE_CS_I04b)

STP yes

Domain industrial

Location indoors

Domain industrial

9.166 Scenario 166: Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. (AISE_CS_I05a, AISE_CS_I05b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product.. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.166 ff. Table 167. Description of ES 166

Free short title Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. (AISE_CS_I05a, AISE_CS_I05b)

PROC 7 - Industrial spraying PROC 7 - Industrial spraying

STP yes

Domain industrial

Location indoors

Domain industrial

9.167 Scenario 167: Spraying of a diluted industrial cleaning or maintenance product during short time. (AISE_CS_I06) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Spraying of a diluted industrial cleaning or maintenance product during short time.. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.167 ff. Table 168. Description of ES 167

Free short title Spraying of a diluted industrial cleaning or maintenance product during short time. (AISE_CS_I06)

STP yes

Concentration in substance 5-25%

Location indoors

Domain industrial

9.168 Scenario 168: Brushing an industrial cleaning solution (AISE_CS_I07a, AISE_CS_I07b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Brushing an industrial cleaning solution. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.168 ff. Table 169. Description of ES 168

Free short title Brushing an industrial cleaning solution (AISE_CS_I07a, AISE_CS_I07b)

STP yes

Domain industrial

Location indoors

Domain industrial

9.169 Scenario 169: Brushing a diluted cleaning or maintenance product (after spraying) (AISE_CS_I08a, AISE_CS_I08b) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Brushing a diluted cleaning or maintenance product (after spraying). The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.169 ff. Table 170. Description of ES 169

Free short title Brushing a diluted cleaning or maintenance product (after spraying) (AISE_CS_I08a, AISE_CS_I08b)

STP yes

Domain industrial

Location indoors

Domain industrial

9.170 Scenario 170: Treatment of articles by dipping or pouring with an industrial cleaning product (AISE_CS_I09) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Treatment of articles by dipping or pouring with an industrial cleaning product. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.170 ff.

Free short title Treatment of articles by dipping or pouring with an industrial cleaning product (AISE_CS_I09)

STP yes

Location indoors

Domain industrial

9.171 Scenario 171: Quality control on industrial cleaning, desinfectants and maintenance Products (AISE_CS_I10) This scenario is described by the following combinations of use descriptors. The corresponding contributing scenarios are described in the respective subchapters. An overall exposure scenario may be described by a number of contributing scenarios which may be subdivided into environmental exposure, worker exposure and consumer exposure. The following scenarios contribute to the scenario Quality control on industrial cleaning, desinfectants and maintenance Products. The corresponding release to the environment, exposure of workers and consumers resulting from these contributing scenarios is summarized in chapter 10.171 ff. Table 172. Description of ES 171

Free short title Quality control on industrial cleaning, desinfectants and maintenance Products (AISE_CS_I10)

STP yes

Location indoors

Domain industrial

2013-04-19 ECPA OWB 2.5 CHEMICAL SAFETY REPORT

10.2 Scenario 2: Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1003a) The following RCR calculations refer to the contributing scenarios described in chapter 9.2 10.2.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.2.1.1 Aquatic compartment (including sediment) Table 299. Environmental risk aquatic of ES 2.1

Compartments PEC PNEC RCR = PEC/PNEC

MSafe kg/d

Freshwater 0.039153 mg/L 0.240 mg/L 0.163139 306.488

Freshwater sediment 0.199662 mg/kgdwt 0.9168 mg/kgdwt 0.217782 229.588

Marine water 0.004159 mg/L 0.024 mg/L 0.173296 288.524

Marine water sediment 0.021209 mg/kgdwt 0.0917 mg/kgdwt 0.231291 216.178

10.2.1.2 Terrestrial compartment Table 300. Environmental risk terrestrial of ES 2.1

MSafe kg/d

Agricultural soil 0.010832 mg/kgdwt 7.5 mg/kgdwt 0.001444 3.72E4

10.2.1.3 Microbiological activity in sewage treatment systems Table 301. Environmental risk STP of ES 2.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

10.2.1.4 Man via environment Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources. Table 302. Environmental risk man via environment of ES 2.1

Food source Exposure concentration (EC)

DNEL Risk characterisation ratio = EC/DNEL

MSafe kg/d

Fish 0.000086 mg/kgbw/day

15 mg/kgbw/day 5.70E-6 -

Root crop 0.000039 mg/kgbw/day

Leaf crop 0.001876 mg/kgbw/day

15 mg/kgbw/day 0.000125 -

Milk 6.01E-7 mg/kgbw/day

Meat 3.23E-8 mg/kgbw/day

Drinking water 0.001055 mg/kgbw/day

15 mg/kgbw/day 0.00007 -

inhalation 0.000047 mg/kgbw/day

Total 0.003104 mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.2.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 24A Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 303. Worker risk of ES 2.2

Route Exposure concentration (EC)

dermal, long-term systemic 0.028286 mg/kgbw/day 2,750 mg/kgbw/day 0.00001

inhalation, long-term systemic 0.200 mg/m3 175 mg/m3 0.001143

Combined routes 0.056857 mg/kgbw/day - 0.001153

10.3 Scenario 3: Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel (AISE-P1003b) The following RCR calculations refer to the contributing scenarios described in chapter 9.3 10.3.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.3.1.1 Aquatic compartment (including sediment)

Table 304. Environmental risk aquatic of ES 3.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.3.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 24A Industrial use of Metal Treatment Products: Hot metal working fluid; Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 308. Worker risk of ES 3.2

10.4 Scenario 4: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting (A.I.S.E. M1) The following RCR calculations refer to the contributing scenarios described in chapter 9.4 10.4.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.4.1.1 Aquatic compartment (including sediment) Table 309. Environmental risk aquatic of ES 4.1

MSafe kg/d

Freshwater 0.038418 mg/L 0.240 mg/L 0.160074 1.04E5

Freshwater sediment 0.195912 mg/kgdwt 0.9168 mg/kgdwt 0.213691 7.82E4

Marine water 0.004086 mg/L 0.024 mg/L 0.170231 9.81E4

Marine water sediment 0.020834 mg/kgdwt 0.0917 mg/kgdwt 0.227201 7.35E4

MSafe kg/d

10.4.1.3 Microbiological activity in sewage treatment systems

Table 311. Environmental risk STP of ES 4.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.4.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 1 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed process, no likelihood of exposure. Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 313. Worker risk of ES 4.2

10.5 Scenario 5: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting (A.I.S.E. M2) The following RCR calculations refer to the contributing scenarios described in chapter 9.5 10.5.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.5.1.1 Aquatic compartment (including sediment) Table 314. Environmental risk aquatic of ES 5.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

Fish 0.000086 15 mg/kgbw/day 5.70E-6 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.5.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed, continous process with occasional controlled exposure (e.g. sampling). Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 318. Worker risk of ES 5.2

10.6 Scenario 6: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting (A.I.S.E. M3) The following RCR calculations refer to the contributing scenarios described in chapter 9.6 10.6.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

10.6.1.1 Aquatic compartment (including sediment) Table 319. Environmental risk aquatic of ES 6.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

Total 0.003104 15 mg/kgbw/day 0.000207 8.07E7

MSafe kg/d

mg/kgbw/day

10.6.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 3 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in closed batch process (synthesis or formulation. Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 323. Worker risk of ES 6.2

10.7 Scenario 7: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting (A.I.S.E. M4) The following RCR calculations refer to the contributing scenarios described in chapter 9.7 10.7.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.7.1.1 Aquatic compartment (including sediment) Table 324. Environmental risk aquatic of ES 7.1

MSafe kg/d

10.7.1.2 Terrestrial compartment

Table 325. Environmental risk terrestrial of ES 7.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.7.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use in batch and other process (synthesis) where opportunity for exposure arises. Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 328. Worker risk of ES 7.2

10.8 Scenario 8: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting (A.I.S.E. M5) The following RCR calculations refer to the contributing scenarios described in chapter 9.8 10.8.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.8.1.1 Aquatic compartment (including sediment) Table 329. Environmental risk aquatic of ES 8.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

10.8.1.4 Man via environment

Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources. Table 332. Environmental risk man via environment of ES 8.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.8.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 5 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Mixing or blending in batch processes for formulation of preparations and articles (multistage and/or significant contact). Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 333. Worker risk of ES 8.2

10.9 Scenario 9: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities. (A.I.S.E. M6) The following RCR calculations refer to the contributing scenarios described in chapter 9.9

10.9.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.9.1.1 Aquatic compartment (including sediment) Table 334. Environmental risk aquatic of ES 9.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.9.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 8B Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation (charging/discharging) from/to vessels/large containers at dedicated facilities. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 338. Worker risk of ES 9.2

10.10 Scenario 10: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting (A.I.S.E. M7) The following RCR calculations refer to the contributing scenarios described in chapter 9.10 10.10.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.10.1.1 Aquatic compartment (including sediment) Table 339. Environmental risk aquatic of ES 10.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.10.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 9 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Transfer of substance or preparation into small containers (dedicated filling line, including weighing). Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 343. Worker risk of ES 10.2

10.11 Scenario 11: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting (A.I.S.E. M8) The following RCR calculations refer to the contributing scenarios described in chapter 9.11 10.11.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.11.1.1 Aquatic compartment (including sediment) Table 344. Environmental risk aquatic of ES 11.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.11.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 14 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Production of preparations or articles by tabletting, compression, extrusion, pelettisation. Industrial setting The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 348. Worker risk of ES 11.2

10.12 Scenario 12: Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent (A.I.S.E. M9) The following RCR calculations refer to the contributing scenarios described in chapter 9.12 10.12.1 Contributing Scenario (1) controlling environmental exposure for ERC2 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.12.1.1 Aquatic compartment (including sediment) Table 349. Environmental risk aquatic of ES 12.1

MSafe kg/d

STP 0.014799 mg/L 1.00E4 mg/L 1.48E-6 1.13E10

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 8.07E7

10.12.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 15 Manufacturing of cleaning and Maintenance Products (main sector of use: SU3 - industrial uses) Use as a laboratory reagent The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 353. Worker risk of ES 12.2

10.13 Scenario 13: Industrial use of Laundry products Laundry detergent; Automatic process (AISE-P101) The following RCR calculations refer to the contributing scenarios described in chapter 9.13 10.13.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Laundry products Laundry detergent; Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.13.1.1 Aquatic compartment (including sediment) Table 354. Environmental risk aquatic of ES 13.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.13.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Laundry products Laundry detergent; Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 358. Worker risk of ES 13.2

10.14 Scenario 14: Industrial use of Laundry products Conditioner (softner/starch); Automatic process (AISE-P104) The following RCR calculations refer to the contributing scenarios described in chapter 9.14 10.14.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Laundry products Conditioner (softner/starch); Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.14.1.1 Aquatic compartment (including sediment) Table 359. Environmental risk aquatic of ES 14.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.14.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Laundry products Conditioner (softner/starch); Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 363. Worker risk of ES 14.2

10.15 Scenario 15: Industrial use of Laundry products Laundry aid (gasing); Automatic process (AISE-P107)

The following RCR calculations refer to the contributing scenarios described in chapter 9.15 10.15.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Laundry products Laundry aid (gasing); Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.15.1.1 Aquatic compartment (including sediment) Table 364. Environmental risk aquatic of ES 15.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.15.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Laundry products Laundry aid (gasing); Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 368. Worker risk of ES 15.2

10.16 Scenario 16: Industrial use of Laundry products Laundry aid (non-gasing); Automatic process (AISE-P110) The following RCR calculations refer to the contributing scenarios described in chapter 9.16 10.16.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Laundry products Laundry aid (non-gasing); Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.16.1.1 Aquatic compartment (including sediment) Table 369. Environmental risk aquatic of ES 16.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.16.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Laundry products Laundry aid (non-gasing); Automatic process

The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 373. Worker risk of ES 16.2

10.17 Scenario 17: Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process (AISE-P707a, AISE-P707b) The following RCR calculations refer to the contributing scenarios described in chapter 9.17 10.17.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.17.1.1 Aquatic compartment (including sediment) Table 374. Environmental risk aquatic of ES 17.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.17.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.17.2.1 Aquatic compartment (including sediment) Table 378. Environmental risk aquatic of ES 17.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.17.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 4 Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 382. Worker risk of ES 17.3

10.17.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 4 Industrial use of Vehicle cleaning Products Train cleaner; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 383. Worker risk of ES 17.4

10.18 Scenario 18: Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process (AISE-P708a, AISE-P708b) The following RCR calculations refer to the contributing scenarios described in chapter 9.18 10.18.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.18.1.1 Aquatic compartment (including sediment) Table 384. Environmental risk aquatic of ES 18.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.18.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.18.2.1 Aquatic compartment (including sediment) Table 388. Environmental risk aquatic of ES 18.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.18.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 4 Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 392. Worker risk of ES 18.3

10.18.6 Contributing Scenario (6) controlling industrial worker exposure for PROC 4 Industrial use of Vehicle cleaning Products Aeroplane cleaner; Semi-Automatic process

10.19 Scenario 19: Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P709a, AISE-P709b) The following RCR calculations refer to the contributing scenarios described in chapter 9.19 10.19.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.19.1.1 Aquatic compartment (including sediment) Table 396. Environmental risk aquatic of ES 19.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.19.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.19.2.1 Aquatic compartment (including sediment) Table 400. Environmental risk aquatic of ES 19.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.19.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 4 Industrial Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 404. Worker risk of ES 19.3

10.20 Scenario 20: Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process (AISE-P710a, AISE-P710b) The following RCR calculations refer to the contributing scenarios described in chapter 9.20 10.20.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.20.1.1 Aquatic compartment (including sediment) Table 408. Environmental risk aquatic of ES 20.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

10.20.1.4 Man via environment Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources.

Table 411. Environmental risk man via environment of ES 20.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.20.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.20.2.1 Aquatic compartment (including sediment) Table 412. Environmental risk aquatic of ES 20.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.20.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 7 Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 416. Worker risk of ES 20.3

10.20.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 7 Industrial Use of Vehicle cleaning Products Car wash product; Spray and rinse process

10.21 Scenario 21: Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process (AISE-P711a, AISE-P711b) The following RCR calculations refer to the contributing scenarios described in chapter 9.21 10.21.1 Contributing Scenario (1) controlling environmental exposure for ERC4

Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.21.1.1 Aquatic compartment (including sediment) Table 420. Environmental risk aquatic of ES 21.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.21.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.21.2.1 Aquatic compartment (including sediment) Table 424. Environmental risk aquatic of ES 21.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.21.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 7 Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 428. Worker risk of ES 21.3

10.21.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 10 Industrial Use of Vehicle cleaning Products Car wash product; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 429. Worker risk of ES 21.4

10.22 Scenario 22: Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P712a, AISE-P712b) The following RCR calculations refer to the contributing scenarios described in chapter 9.22 10.22.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.22.1.1 Aquatic compartment (including sediment) Table 430. Environmental risk aquatic of ES 22.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.22.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.22.2.1 Aquatic compartment (including sediment) Table 434. Environmental risk aquatic of ES 22.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.22.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 4 Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 438. Worker risk of ES 22.3

10.22.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 4 Industrial Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process

10.23 Scenario 23: Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic (AISE-P713) The following RCR calculations refer to the contributing scenarios described in chapter 9.23 10.23.1 Contributing Scenario (1) controlling environmental exposure for ERC4

Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.23.1.1 Aquatic compartment (including sediment) Table 442. Environmental risk aquatic of ES 23.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.23.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 10 Industrial Use of Vehicle cleaning Products Boat cleaning; semi automatic The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 446. Worker risk of ES 23.2

10.24 Scenario 24: Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process (AISE-P714a, AISE-P714b) The following RCR calculations refer to the contributing scenarios described in chapter 9.24 10.24.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.24.1.1 Aquatic compartment (including sediment) Table 447. Environmental risk aquatic of ES 24.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.24.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.24.2.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.24.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 7 Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 455. Worker risk of ES 24.3

10.24.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 10 Industrial Use of Vehicle cleaning Products Boat cleaner; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 456. Worker risk of ES 24.4

10.25 Scenario 25: Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process (AISE-P801) The following RCR calculations refer to the contributing scenarios described in chapter 9.25 10.25.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.25.1.1 Aquatic compartment (including sediment) Table 457. Environmental risk aquatic of ES 25.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.25.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 1 Industrial use of Food beverage and pharmacos products Process cleaner; Cleaning In place (CIP) process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 461. Worker risk of ES 25.2

10.26 Scenario 26: Industrial use of Food beverage and pharmacos products Process cleaner; Semi closed cleaning process (AISE-P802) The following RCR calculations refer to the contributing scenarios described in chapter 9.26 10.26.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Process cleaner; Semi closed cleaning process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.26.1.1 Aquatic compartment (including sediment) Table 462. Environmental risk aquatic of ES 26.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.26.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Food beverage and pharmacos products Process cleaner; Semi closed cleaning process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 466. Worker risk of ES 26.2

10.27 Scenario 27: Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process

(AISE-P803) The following RCR calculations refer to the contributing scenarios described in chapter 9.27 10.27.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.27.1.1 Aquatic compartment (including sediment) Table 467. Environmental risk aquatic of ES 27.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

Leaf crop 0.001876 15 mg/kgbw/day 0.000125 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.27.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic spray process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 471. Worker risk of ES 27.2

10.28 Scenario 28: Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process (AISE-P804) The following RCR calculations refer to the contributing scenarios described in chapter 9.28 10.28.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.28.1.1 Aquatic compartment (including sediment) Table 472. Environmental risk aquatic of ES 28.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.28.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 13 Industrial use of Food beverage and pharmacos products Chain maintenance product; Automatic drip and brush process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 476. Worker risk of ES 28.2

10.29 Scenario 29: Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process (AISE-P805) The following RCR calculations refer to the contributing scenarios described in chapter 9.29 10.29.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.29.1.1 Aquatic compartment (including sediment) Table 477. Environmental risk aquatic of ES 29.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.29.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 1 Industrial use of Food beverage and pharmacos products Defoaming product; Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 481. Worker risk of ES 29.2

10.30 Scenario 30: Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process

(AISE-P806) The following RCR calculations refer to the contributing scenarios described in chapter 9.30 10.30.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.30.1.1 Aquatic compartment (including sediment) Table 482. Environmental risk aquatic of ES 30.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.30.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic with venting process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 486. Worker risk of ES 30.2

10.31 Scenario 31: Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process (AISE-P807) The following RCR calculations refer to the contributing scenarios described in chapter 9.31 10.31.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.31.1.1 Aquatic compartment (including sediment) Table 487. Environmental risk aquatic of ES 31.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.31.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial use of Food beverage and pharmacos products Foam cleaner; Semi-Automatic without venting process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 491. Worker risk of ES 31.2

10.32 Scenario 32: Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process (AISE-P809) The following RCR calculations refer to the contributing scenarios described in chapter 9.32 10.32.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.32.1.1 Aquatic compartment (including sediment) Table 492. Environmental risk aquatic of ES 32.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.32.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial use of Food beverage and pharmacos products Animal housing care; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 496. Worker risk of ES 32.2

10.33 Scenario 33: Industrial use of pharmacos products Disinfection product; Semi-automatic process (AISE-P810)

The following RCR calculations refer to the contributing scenarios described in chapter 9.33 10.33.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of pharmacos products Disinfection product; Semi-automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.33.1.1 Aquatic compartment (including sediment) Table 497. Environmental risk aquatic of ES 33.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.33.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of pharmacos products Disinfection product; Semi-automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 501. Worker risk of ES 33.2

10.34 Scenario 34: Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process (AISE-P811) The following RCR calculations refer to the contributing scenarios described in chapter 9.34 10.34.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.34.1.1 Aquatic compartment (including sediment) Table 502. Environmental risk aquatic of ES 34.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.34.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial use of Food beverage and pharmacos products Disinfection product; Fogging and gassing Semi-automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 506. Worker risk of ES 34.2

10.35 Scenario 35: Industrial use of Water treatment Products Preservation and sanitation agent ; Process water (AISE-P903) The following RCR calculations refer to the contributing scenarios described in chapter 9.35 10.35.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Water treatment Products Preservation and sanitation agent ; Process water The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.35.1.1 Aquatic compartment (including sediment) Table 507. Environmental risk aquatic of ES 35.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.35.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Water treatment Products Preservation and sanitation agent ; Process water The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 511. Worker risk of ES 35.2

10.36 Scenario 36: Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water (AISE-P904)

The following RCR calculations refer to the contributing scenarios described in chapter 9.36 10.36.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.36.1.1 Aquatic compartment (including sediment) Table 512. Environmental risk aquatic of ES 36.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.36.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Water treatment Products Preservation and sanitation agent ; Drink and pool water The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 516. Worker risk of ES 36.2

10.37 Scenario 37: Industrial use of Water treatment Products Sanitation agent; Waste water (AISE-P905) The following RCR calculations refer to the contributing scenarios described in chapter 9.37 10.37.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Water treatment Products Sanitation agent; Waste water The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.37.1.1 Aquatic compartment (including sediment) Table 517. Environmental risk aquatic of ES 37.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.37.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Water treatment Products Sanitation agent; Waste water

10.38 Scenario 38: Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P906) The following RCR calculations refer to the contributing scenarios described in chapter 9.38 10.38.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.38.1.1 Aquatic compartment (including sediment) Table 522. Environmental risk aquatic of ES 38.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.38.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 526. Worker risk of ES 38.2

10.39 Scenario 39: Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P907) The following RCR calculations refer to the contributing scenarios described in chapter 9.39 10.39.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process

The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.39.1.1 Aquatic compartment (including sediment) Table 527. Environmental risk aquatic of ES 39.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

Drinking water 0.001055 15 mg/kgbw/day 0.00007 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.39.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Industrial Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 531. Worker risk of ES 39.2

10.40 Scenario 40: Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1001a, AISE-P1001b) The following RCR calculations refer to the contributing scenarios described in chapter 9.40 10.40.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.40.1.1 Aquatic compartment (including sediment) Table 532. Environmental risk aquatic of ES 40.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.40.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

Total 0.003104 15 mg/kgbw/day 0.000207 2.42E5

MSafe kg/d

mg/kgbw/day

10.40.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 540. Worker risk of ES 40.3

dermal, long-term systemic 0.013714 mg/kgbw/day 2,750 mg/kgbw/day 4.99E-6

10.40.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 541. Worker risk of ES 40.4

10.41 Scenario 41: Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel (AISE-P1001a, AISE-P1001b) The following RCR calculations refer to the contributing scenarios described in chapter 9.41 10.41.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk

Assessment Spreadsheet Model 1.24a. 10.41.1.1 Aquatic compartment (including sediment) Table 542. Environmental risk aquatic of ES 41.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

inhalation 0.000047 15 mg/kgbw/day 3.12E-6 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.41.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.41.2.1 Aquatic compartment (including sediment) Table 546. Environmental risk aquatic of ES 41.2

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.41.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 550. Worker risk of ES 41.3

10.41.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Conversion Layer agent; Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 551. Worker risk of ES 41.4

10.42 Scenario 42: Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1002a) The following RCR calculations refer to the contributing scenarios described in chapter 9.42 10.42.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.42.1.1 Aquatic compartment (including sediment) Table 552. Environmental risk aquatic of ES 42.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.42.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 17 Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 556. Worker risk of ES 42.2

10.43 Scenario 43: Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel (AISE-P1002b) The following RCR calculations refer to the contributing scenarios described in chapter 9.43 10.43.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 2.42E5

10.43.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 17 Industrial use of Metal Treatment Products* Metal working fluid (rolling oils, lubricants); Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 561. Worker risk of ES 43.2

10.44 Scenario 44: Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1003a) The following RCR calculations refer to the contributing scenarios described in chapter 9.44 10.44.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.44.1.1 Aquatic compartment (including sediment) Table 562. Environmental risk aquatic of ES 44.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.44.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 24A Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 566. Worker risk of ES 44.2

10.45 Scenario 45: Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel (AISE-P1003b) The following RCR calculations refer to the contributing scenarios described in chapter 9.45 10.45.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.45.1.1 Aquatic compartment (including sediment) Table 567. Environmental risk aquatic of ES 45.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.45.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 24A Industrial use of Metal Treatment Products* Hot metal working fluid; Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 571. Worker risk of ES 45.2

10.46 Scenario 46: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1004a) The following RCR calculations refer to the contributing scenarios described in chapter 9.46 10.46.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 2.42E5

10.46.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 10 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 576. Worker risk of ES 46.2

10.47 Scenario 47: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel (AISE-P1004b) The following RCR calculations refer to the contributing scenarios described in chapter 9.47 10.47.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.47.1.1 Aquatic compartment (including sediment) Table 577. Environmental risk aquatic of ES 47.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.47.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 10 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Manual process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 581. Worker risk of ES 47.2

10.48 Scenario 48: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1005a) The following RCR calculations refer to the contributing scenarios described in chapter 9.48 10.48.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.48.1.1 Aquatic compartment (including sediment) Table 582. Environmental risk aquatic of ES 48.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

10.48.1.4 Man via environment Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table shows the calculated exposure to the substance from exemplary food sources at different trophic levels together

with the total exposure over all routes and food sources. Table 585. Environmental risk man via environment of ES 48.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.48.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 586. Worker risk of ES 48.2

10.49 Scenario 49: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel (AISE-P1005b) The following RCR calculations refer to the contributing scenarios described in chapter 9.49 10.49.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.49.1.1 Aquatic compartment (including sediment) Table 587. Environmental risk aquatic of ES 49.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 2.42E5

10.49.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Semi-automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 591. Worker risk of ES 49.2

10.50 Scenario 50: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1006a) The following RCR calculations refer to the contributing scenarios described in chapter 9.50 10.50.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.50.1.1 Aquatic compartment (including sediment) Table 592. Environmental risk aquatic of ES 50.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.50.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

Table 596. Worker risk of ES 50.2

10.51 Scenario 51: Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process (AISE-P1006b) The following RCR calculations refer to the contributing scenarios described in chapter 9.51 10.51.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.51.1.1 Aquatic compartment (including sediment) Table 597. Environmental risk aquatic of ES 51.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.51.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Metal cleaner (degreaser, descaler, etch); Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 601. Worker risk of ES 51.2

10.52 Scenario 52: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1007a) The following RCR calculations refer to the contributing scenarios described in chapter 9.52 10.52.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.52.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 606. Worker risk of ES 52.2

10.53 Scenario 53: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel (AISE-P1007b) The following RCR calculations refer to the contributing scenarios described in chapter 9.53 10.53.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.53.1.1 Aquatic compartment (including sediment) Table 607. Environmental risk aquatic of ES 53.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.53.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Automatic process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 611. Worker risk of ES 53.2

10.54 Scenario 54: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese (AISE-P1008a) The following RCR calculations refer to the contributing scenarios described in chapter 9.54 10.54.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.54.1.1 Aquatic compartment (including sediment) Table 612. Environmental risk aquatic of ES 54.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.54.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 616. Worker risk of ES 54.2

10.55 Scenario 55: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process (AISE-P1008b) The following RCR calculations refer to the contributing scenarios described in chapter 9.55 10.55.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 2.42E5

10.55.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 621. Worker risk of ES 55.2

10.56 Scenario 56: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese (AISE-P1009a) The following RCR calculations refer to the contributing scenarios described in chapter 9.56 10.56.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.56.1.1 Aquatic compartment (including sediment) Table 622. Environmental risk aquatic of ES 56.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.56.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 10 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.57 Scenario 57: Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel (AISE-P1009b) The following RCR calculations refer to the contributing scenarios described in chapter 9.57 10.57.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.57.1.1 Aquatic compartment (including sediment) Table 627. Environmental risk aquatic of ES 57.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

10.57.1.4 Man via environment Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table

shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources. Table 630. Environmental risk man via environment of ES 57.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.57.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 10 Industrial use of Metal Treatment Products* Coating product (Paint, filler, Putty, Thinner); Manual process, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 631. Worker risk of ES 57.2

10.58 Scenario 58: Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1010a) The following RCR calculations refer to the contributing scenarios described in chapter 9.58 10.58.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.58.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 636. Worker risk of ES 58.2

10.59 Scenario 59: Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel (AISE-P1010b) The following RCR calculations refer to the contributing scenarios described in chapter 9.59 10.59.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.59.1.1 Aquatic compartment (including sediment) Table 637. Environmental risk aquatic of ES 59.1

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.59.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with no process water recycling, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.60 Scenario 60: Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese (AISE-P1011a) The following RCR calculations refer to the contributing scenarios described in chapter 9.60 10.60.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.60.1.1 Aquatic compartment (including sediment) Table 642. Environmental risk aquatic of ES 60.1

MSafe kg/d

STP 0.022154 mg/L 1.00E4 mg/L 2.22E-6 2.26E7

10.60.1.4 Man via environment

Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources. Table 645. Environmental risk man via environment of ES 60.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.60.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Zinc, Chromium, Copper, Manganese The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 646. Worker risk of ES 60.2

10.61 Scenario 61: Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel (AISE-P1011b) The following RCR calculations refer to the contributing scenarios described in chapter 9.61 10.61.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel

MSafe kg/d

STP 0.004431 mg/L 1.00E4 mg/L 4.43E-7 1.13E8

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.61.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 4 Industrial use of Metal Treatment Products* Surface finishing product; Manual with process water recycling, Nickel The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 651. Worker risk of ES 61.2

10.62 Scenario 62: Industrial use of Quality control Laboratory Reagents (AISE-P1250) The following RCR calculations refer to the contributing scenarios described in chapter 9.62 10.62.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Industrial use of Quality control Laboratory Reagents The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.62.1.1 Aquatic compartment (including sediment) Table 652. Environmental risk aquatic of ES 62.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.62.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 15 Industrial use of Quality control Laboratory Reagents The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 656. Worker risk of ES 62.2

10.63 Scenario 63: Professional Use of Laundry products Laundry detergent; Semi automatic process (AISE-P102) The following RCR calculations refer to the contributing scenarios described in chapter 9.63 10.63.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Laundry products Laundry detergent; Semi automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.63.1.1 Aquatic compartment (including sediment) Table 657. Environmental risk aquatic of ES 63.1

MSafe kg/d

Agricultural soil 0.010688 mg/kgdwt 7.5 mg/kgdwt 0.001425 1,530.908

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.63.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Laundry products Laundry detergent; Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 661. Worker risk of ES 63.2

10.64 Scenario 64: Professional Use of Laundry products Laundry detergent; Manual process (AISE-P103) The following RCR calculations refer to the contributing scenarios described in chapter 9.64 10.64.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Laundry products Laundry detergent; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.64.1.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.64.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Laundry products Laundry detergent; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 666. Worker risk of ES 64.2

10.65 Scenario 65: Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process (AISE-P105) The following RCR calculations refer to the contributing scenarios described in chapter 9.65 10.65.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.65.1.1 Aquatic compartment (including sediment) Table 667. Environmental risk aquatic of ES 65.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.65.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 671. Worker risk of ES 65.2

10.65.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Laundry products Conditioner (softener/starch); Semi automatic process

10.66 Scenario 66: Professional Use of Laundry products Laundry aid (gasing); Semi automatic process (AISE-P108) The following RCR calculations refer to the contributing scenarios described in chapter 9.66 10.66.1 Contributing Scenario (1) controlling environmental exposure for ERC8B Professional Use of Laundry products Laundry aid (gasing); Semi automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.66.1.1 Aquatic compartment (including sediment) Table 673. Environmental risk aquatic of ES 66.1

MSafe kg/d

STP 0.000971 mg/L 1.00E4 mg/L 9.71E-8 5.64E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.65E4

10.66.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Laundry products Laundry aid (gasing); Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 677. Worker risk of ES 66.2

10.66.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Laundry products Laundry aid (gasing); Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.67 Scenario 67: Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process (AISE-P111) The following RCR calculations refer to the contributing scenarios described in chapter 9.67 10.67.1 Contributing Scenario (1) controlling environmental exposure for ERC8B Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.67.1.1 Aquatic compartment (including sediment) Table 679. Environmental risk aquatic of ES 67.1

MSafe kg/d

STP 0.000971 mg/L 1.00E4 mg/L 9.71E-8 5.64E7

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.65E4

10.67.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 683. Worker risk of ES 67.2

10.67.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Laundry products Laundry aid (non-gasing); Semi automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 684. Worker risk of ES 67.3

10.68 Scenario 68: Professional Use of Laundry products Laundry aid (non-gasing); Manual process (AISE-P112) The following RCR calculations refer to the contributing scenarios described in chapter 9.68 10.68.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Laundry products Laundry aid (non-gasing); Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.68.1.1 Aquatic compartment (including sediment) Table 685. Environmental risk aquatic of ES 68.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.68.2 Contributing Scenario (2) controlling professional worker exposure for PROC 4 Professional Use of Laundry products Laundry aid (non-gasing); Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 689. Worker risk of ES 68.2

10.69 Scenario 69: Professional Use of Laundry products Prespotter/Stain remover; Manual process (AISE-P113a, AISE-P113b) The following RCR calculations refer to the contributing scenarios described in chapter 9.69 10.69.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Laundry products Prespotter/Stain remover; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.69.1.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.69.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Laundry products Prespotter/Stain remover; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.69.2.1 Aquatic compartment (including sediment) Table 694. Environmental risk aquatic of ES 69.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.69.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Laundry products Prespotter/Stain remover; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 698. Worker risk of ES 69.3

10.69.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Laundry products Prespotter/Stain remover; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 699. Worker risk of ES 69.4

10.70 Scenario 70: Professional Use of Dishwash products Dishwash product; Manual process (AISE-P201) The following RCR calculations refer to the contributing scenarios described in chapter 9.70

10.70.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Dishwash products Dishwash product; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.70.1.1 Aquatic compartment (including sediment) Table 700. Environmental risk aquatic of ES 70.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.70.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Dishwash products Dishwash product; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 704. Worker risk of ES 70.2

10.71 Scenario 71: Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process (AISE-P202) The following RCR calculations refer to the contributing scenarios described in chapter 9.71 10.71.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.71.1.1 Aquatic compartment (including sediment) Table 705. Environmental risk aquatic of ES 71.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.71.2 Contributing Scenario (2) controlling professional worker exposure for PROC 2 Professional Use of Dishwash products Dishwash and rinse aid product; Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.72 Scenario 72: Professional Use of Dishwash products Dishwash product; Semi-Automatic process (AISE-P203) The following RCR calculations refer to the contributing scenarios described in chapter 9.72 10.72.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Dishwash products Dishwash product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.72.1.1 Aquatic compartment (including sediment) Table 710. Environmental risk aquatic of ES 72.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.72.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Dishwash products Dishwash product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 714. Worker risk of ES 72.2

10.72.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Dishwash products Dishwash product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 715. Worker risk of ES 72.3

10.73 Scenario 73: Professional Use of Dishwash products Rinse aid; Semi-Automatic process (AISE-P204) The following RCR calculations refer to the contributing scenarios described in chapter 9.73 10.73.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Dishwash products Rinse aid; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.73.1.1 Aquatic compartment (including sediment) Table 716. Environmental risk aquatic of ES 73.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.73.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Dishwash products Rinse aid; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 720. Worker risk of ES 73.2

10.73.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Dishwash products Rinse aid; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 721. Worker risk of ES 73.3

10.74 Scenario 74: Professional Use of General surface cleaning products General purpose cleaner; Manual process (AISE-P301) The following RCR calculations refer to the contributing scenarios described in chapter 9.74 10.74.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products General purpose cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.74.1.1 Aquatic compartment (including sediment) Table 722. Environmental risk aquatic of ES 74.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.74.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products General purpose cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 726. Worker risk of ES 74.2

10.75 Scenario 75: Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process (AISE-P302a, AISE-P302b) The following RCR calculations refer to the contributing scenarios described in chapter 9.75 10.75.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.75.1.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.75.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.75.2.1 Aquatic compartment (including sediment) Table 731. Environmental risk aquatic of ES 75.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.75.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 735. Worker risk of ES 75.3

10.75.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products General purpose cleaner; Spray and wipe; manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 736. Worker risk of ES 75.4

10.76 Scenario 76: Professional Use of General surface cleaning products Kitchen cleaner; Manual process (AISE-P303) The following RCR calculations refer to the contributing scenarios described in chapter 9.76

10.76.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Kitchen cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.76.1.1 Aquatic compartment (including sediment) Table 737. Environmental risk aquatic of ES 76.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.76.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Kitchen cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 741. Worker risk of ES 76.2

10.77 Scenario 77: Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process (AISE-P304a, AISE-P304b) The following RCR calculations refer to the contributing scenarios described in chapter 9.77 10.77.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.77.1.1 Aquatic compartment (including sediment) Table 742. Environmental risk aquatic of ES 77.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.77.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 9,931.113

10.77.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 750. Worker risk of ES 77.3

10.77.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Kitchen cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 751. Worker risk of ES 77.4

10.78 Scenario 78: Professional Use of General surface cleaning products Sanitary cleaner; Manual process (AISE-P305) The following RCR calculations refer to the contributing scenarios described in chapter 9.78 10.78.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Sanitary cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.78.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Sanitary cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 756. Worker risk of ES 78.2

10.79 Scenario 79: Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process (AISE-P306a, AISE-P306b) The following RCR calculations refer to the contributing scenarios described in chapter 9.79 10.79.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.79.1.1 Aquatic compartment (including sediment) Table 757. Environmental risk aquatic of ES 79.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.79.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.79.2.1 Aquatic compartment (including sediment) Table 761. Environmental risk aquatic of ES 79.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.79.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 765. Worker risk of ES 79.3

10.79.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Sanitary cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 766. Worker risk of ES 79.4

10.80 Scenario 80: Professional Use of General surface cleaning products Descaling agent; Manual process (AISE-P307) The following RCR calculations refer to the contributing scenarios described in chapter 9.80 10.80.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Descaling agent; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.80.1.1 Aquatic compartment (including sediment) Table 767. Environmental risk aquatic of ES 80.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.80.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Descaling agent; Manual process

10.81 Scenario 81: Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process (AISE-P308a, AISE-P308b) The following RCR calculations refer to the contributing scenarios described in chapter 9.81 10.81.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.81.1.1 Aquatic compartment (including sediment) Table 772. Environmental risk aquatic of ES 81.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.81.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.81.2.1 Aquatic compartment (including sediment) Table 776. Environmental risk aquatic of ES 81.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.81.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 780. Worker risk of ES 81.3

10.81.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Descaling agent; Spray and rinse manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 781. Worker risk of ES 81.4

10.82 Scenario 82: Professional Use of General surface cleaning products Periodic cleaning by dipping (AISE-P309) The following RCR calculations refer to the contributing scenarios described in chapter 9.82 10.82.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Periodic cleaning by dipping The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.82.1.1 Aquatic compartment (including sediment) Table 782. Environmental risk aquatic of ES 82.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.82.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Professional Use of General surface cleaning products Periodic cleaning by dipping The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 786. Worker risk of ES 82.2

10.83 Scenario 83: Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process (AISE-P310) The following RCR calculations refer to the contributing scenarios described in chapter 9.83 10.83.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.83.1.1 Aquatic compartment (including sediment) Table 787. Environmental risk aquatic of ES 83.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.83.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Oven/Grill Cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 791. Worker risk of ES 83.2

10.84 Scenario 84: Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process (AISE-P311a, AISE-P311b) The following RCR calculations refer to the contributing scenarios described in chapter 9.84 10.84.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

Total 0.003104 15 mg/kgbw/day 0.000207 9,931.113

MSafe kg/d

mg/kgbw/day

10.84.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.84.2.1 Aquatic compartment (including sediment) Table 796. Environmental risk aquatic of ES 84.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.84.3 Contributing Scenario (3) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 800. Worker risk of ES 84.3

10.84.4 Contributing Scenario (4) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Oven/Grill Cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 801. Worker risk of ES 84.4

10.85 Scenario 85: Professional Use of General surface cleaning products Glass cleaner; Manual process (AISE-P312) The following RCR calculations refer to the contributing scenarios described in chapter 9.85 10.85.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Glass cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.85.1.1 Aquatic compartment (including sediment) Table 802. Environmental risk aquatic of ES 85.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.85.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Glass cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 806. Worker risk of ES 85.2

10.86 Scenario 86: Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process (AISE-P313a, AISE-P313b) The following RCR calculations refer to the contributing scenarios described in chapter 9.86 10.86.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.86.1.1 Aquatic compartment (including sediment) Table 807. Environmental risk aquatic of ES 86.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.86.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.86.2.1 Aquatic compartment (including sediment) Table 811. Environmental risk aquatic of ES 86.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.86.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 815. Worker risk of ES 86.3

10.86.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Glass cleaner ; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 816. Worker risk of ES 86.4

10.87 Scenario 87: Professional Use of General surface cleaning products Surface disinfectant; Manual process (AISE-P314) The following RCR calculations refer to the contributing scenarios described in chapter 9.87 10.87.1 Contributing Scenario (1) controlling environmental exposure for ERC8A

Professional Use of General surface cleaning products Surface disinfectant; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.87.1.1 Aquatic compartment (including sediment) Table 817. Environmental risk aquatic of ES 87.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.87.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Surface disinfectant; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 821. Worker risk of ES 87.2

10.88 Scenario 88: Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process (AISE-P315a, AISE-P315b) The following RCR calculations refer to the contributing scenarios described in chapter 9.88 10.88.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.88.1.1 Aquatic compartment (including sediment) Table 822. Environmental risk aquatic of ES 88.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.88.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.88.2.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.88.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 830. Worker risk of ES 88.3

10.88.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Surface disinfectant; Spray and rinse manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 831. Worker risk of ES 88.4

10.89 Scenario 89: Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process (AISE-P316) The following RCR calculations refer to the contributing scenarios described in chapter 9.89 10.89.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.89.1.1 Aquatic compartment (including sediment) Table 832. Environmental risk aquatic of ES 89.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.89.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Metal cleaning agent (including silver and copper polishes); Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 836. Worker risk of ES 89.2

10.90 Scenario 90: Professional Use of General surface cleaning products Wet wipes; Manual process (AISE-P317) The following RCR calculations refer to the contributing scenarios described in chapter 9.90 10.90.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of General surface cleaning products Wet wipes; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.90.1.1 Aquatic compartment (including sediment) Table 837. Environmental risk aquatic of ES 90.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.90.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of General surface cleaning products Wet wipes; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 841. Worker risk of ES 90.2

10.91 Scenario 91: Professional Use of Floor care products Floor cleaner; Semi-Automatic process (AISE-P401)

The following RCR calculations refer to the contributing scenarios described in chapter 9.91 10.91.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.91.1.1 Aquatic compartment (including sediment) Table 842. Environmental risk aquatic of ES 91.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.91.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor cleaner; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 846. Worker risk of ES 91.2

10.92 Scenario 92: Professional Use of Floor care products Floor cleaner; Spray and wipe manual process (AISE-P402a, AISE-P402b) The following RCR calculations refer to the contributing scenarios described in chapter 9.92 10.92.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.92.1.1 Aquatic compartment (including sediment) Table 847. Environmental risk aquatic of ES 92.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.92.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor cleaner; Spray and wipe manual process

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 9,931.113

10.92.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Floor care products Floor cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 855. Worker risk of ES 92.3

10.92.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 856. Worker risk of ES 92.4

10.93 Scenario 93: Professional Use of Floor care products Floor cleaner; Manual process (AISE-P403a, AISE-P403b) The following RCR calculations refer to the contributing scenarios described in chapter 9.93 10.93.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.93.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.93.2.1 Aquatic compartment (including sediment) Table 861. Environmental risk aquatic of ES 93.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.93.3 Contributing Scenario (3) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 865. Worker risk of ES 93.3

10.93.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 866. Worker risk of ES 93.4

10.94 Scenario 94: Professional Use of Floor care products Floor stripper; Manual process (AISE-P404) The following RCR calculations refer to the contributing scenarios described in chapter 9.94 10.94.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor stripper; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.94.1.1 Aquatic compartment (including sediment) Table 867. Environmental risk aquatic of ES 94.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.94.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor stripper; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 871. Worker risk of ES 94.2

10.95 Scenario 95: Professional Use of Floor care products Floor stripper; Semi-Automatic process (AISE-P405) The following RCR calculations refer to the contributing scenarios described in chapter 9.95 10.95.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Floor stripper; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.95.1.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.95.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Floor stripper; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 876. Worker risk of ES 95.2

10.96 Scenario 96: Professional Use of Floor care products Polish / impregnating agent; Manual process (AISE-P406) The following RCR calculations refer to the contributing scenarios described in chapter 9.96 10.96.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Polish / impregnating agent; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.96.1.1 Aquatic compartment (including sediment) Table 877. Environmental risk aquatic of ES 96.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.96.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Polish / impregnating agent; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 881. Worker risk of ES 96.2

10.97 Scenario 97: Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process (AISE-P407)

The following RCR calculations refer to the contributing scenarios described in chapter 9.97 10.97.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.97.1.1 Aquatic compartment (including sediment) Table 882. Environmental risk aquatic of ES 97.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.97.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Polish / impregnating agent; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 886. Worker risk of ES 97.2

10.98 Scenario 98: Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process (AISE-P408a, AISE-P408b) The following RCR calculations refer to the contributing scenarios described in chapter 9.98 10.98.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.98.1.1 Aquatic compartment (including sediment) Table 887. Environmental risk aquatic of ES 98.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.98.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.98.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 895. Worker risk of ES 98.3

10.98.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Polish / impregnating agent; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 896. Worker risk of ES 98.4

10.99 Scenario 99: Professional Use of Floor care products Carpet cleaner; Manual process (AISE-P409) The following RCR calculations refer to the contributing scenarios described in chapter 9.99 10.99.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Carpet cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.99.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Carpet cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 901. Worker risk of ES 99.2

10.100 Scenario 100: Professional Use of Floor care products Carpet cleaner; Semi-Automatic process (AISE-P410) The following RCR calculations refer to the contributing scenarios described in chapter 9.100 10.100.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Carpet cleaner; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.100.1.1 Aquatic compartment (including sediment) Table 902. Environmental risk aquatic of ES 100.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.100.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Carpet cleaner; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 906. Worker risk of ES 100.2

10.101 Scenario 101: Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process (AISE-P411a, AISE-P411b) The following RCR calculations refer to the contributing scenarios described in chapter 9.101 10.101.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.101.1.1 Aquatic compartment (including sediment) Table 907. Environmental risk aquatic of ES 101.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.101.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.101.2.1 Aquatic compartment (including sediment) Table 911. Environmental risk aquatic of ES 101.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.101.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 915. Worker risk of ES 101.3

10.101.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Floor care products Carpet pre-spotters; Spray and brush manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 916. Worker risk of ES 101.4

10.102 Scenario 102: Professional Use of Maintenance Products Wooden Furniture care product; Manual process (AISE-P601) The following RCR calculations refer to the contributing scenarios described in chapter 9.102 10.102.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Wooden Furniture care product; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.102.1.1 Aquatic compartment (including sediment) Table 917. Environmental risk aquatic of ES 102.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.102.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Wooden Furniture care product; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 921. Worker risk of ES 102.2

10.103 Scenario 103: Professional Use of Maintenance Products Wooden

Furniture care product; Spray and wipe manual process (AISE-P602a, AISE-P602b) The following RCR calculations refer to the contributing scenarios described in chapter 9.103 10.103.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.103.1.1 Aquatic compartment (including sediment) Table 922. Environmental risk aquatic of ES 103.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.103.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.103.2.1 Aquatic compartment (including sediment) Table 926. Environmental risk aquatic of ES 103.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.103.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 930. Worker risk of ES 103.3

10.103.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Wooden Furniture care product; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total

exposure of workers over all routes if applicable. Table 931. Worker risk of ES 103.4

10.104 Scenario 104: Professional Use of Maintenance Products Leather care product; Manual process (AISE-P603) The following RCR calculations refer to the contributing scenarios described in chapter 9.104 10.104.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Leather care product; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.104.1.1 Aquatic compartment (including sediment) Table 932. Environmental risk aquatic of ES 104.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

10.104.1.4 Man via environment Secondary poisoning considers indirect exposure of man via foods, air and drinking water. The following table

shows the calculated exposure to the substance from exemplary food sources at different trophic levels together with the total exposure over all routes and food sources. Table 935. Environmental risk man via environment of ES 104.1

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.104.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Leather care product; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 936. Worker risk of ES 104.2

10.105 Scenario 105: Professional Use of Maintenance Products Leather care product; Spray and wipe manual process (AISE-P604a, AISE-P604b) The following RCR calculations refer to the contributing scenarios described in chapter 9.105 10.105.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Leather care product; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.105.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Leather care product; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.105.2.1 Aquatic compartment (including sediment) Table 941. Environmental risk aquatic of ES 105.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.105.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Maintenance Products Leather care product; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 945. Worker risk of ES 105.3

10.105.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Leather care product; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 946. Worker risk of ES 105.4

10.106 Scenario 106: Professional Use of Maintenance Products Leather care product; Semi-Automatic process (AISE-P605) The following RCR calculations refer to the contributing scenarios described in chapter 9.106 10.106.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Leather care product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.106.1.1 Aquatic compartment (including sediment) Table 947. Environmental risk aquatic of ES 106.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.106.2 Contributing Scenario (2) controlling professional worker exposure for PROC 2 Professional Use of Maintenance Products Leather care product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 951. Worker risk of ES 106.2

10.107 Scenario 107: Professional Use of Maintenance Products Drain unblocker; Manual process (AISE-P606) The following RCR calculations refer to the contributing scenarios described in chapter 9.107 10.107.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Drain unblocker; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.107.1.1 Aquatic compartment (including sediment)

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.107.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Professional Use of Maintenance Products Drain unblocker; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 956. Worker risk of ES 107.2

10.108 Scenario 108: Professional Use of Maintenance Products Drain cleaner; Manual process (AISE-P607) The following RCR calculations refer to the contributing scenarios described in chapter 9.108 10.108.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Drain cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.108.1.1 Aquatic compartment (including sediment) Table 957. Environmental risk aquatic of ES 108.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.108.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Professional Use of Maintenance Products Drain cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 961. Worker risk of ES 108.2

10.109 Scenario 109: Professional Use of Maintenance Products Stainless

steel care ; Manual process (AISE-P608) The following RCR calculations refer to the contributing scenarios described in chapter 9.109 10.109.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Stainless steel care ; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.109.1.1 Aquatic compartment (including sediment) Table 962. Environmental risk aquatic of ES 109.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.109.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Stainless steel care ; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 966. Worker risk of ES 109.2

10.110 Scenario 110: Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process (AISE-P609a, AISE-P609b) The following RCR calculations refer to the contributing scenarios described in chapter 9.110 10.110.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.110.1.1 Aquatic compartment (including sediment) Table 967. Environmental risk aquatic of ES 110.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.110.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.110.2.1 Aquatic compartment (including sediment) Table 971. Environmental risk aquatic of ES 110.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.110.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 975. Worker risk of ES 110.3

10.110.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Maintenance Products Stainless steel care; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 976. Worker risk of ES 110.4

10.111 Scenario 111: Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process (AISE-P701a, AISE-P701b) The following RCR calculations refer to the contributing scenarios described in chapter 9.111

10.111.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.111.1.1 Aquatic compartment (including sediment) Table 977. Environmental risk aquatic of ES 111.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.111.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.111.2.1 Aquatic compartment (including sediment) Table 981. Environmental risk aquatic of ES 111.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.111.3 Contributing Scenario (3) controlling professional worker exposure for PROC 4 Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 985. Worker risk of ES 111.3

10.111.4 Contributing Scenario (4) controlling professional worker exposure for PROC 4 Professional Use of Vehicle cleaning Products Car wash product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 986. Worker risk of ES 111.4

10.112 Scenario 112: Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process (AISE-P702a, AISE-P702b) The following RCR calculations refer to the contributing scenarios described in chapter 9.112 10.112.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.112.1.1 Aquatic compartment (including sediment) Table 987. Environmental risk aquatic of ES 112.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.112.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.112.2.1 Aquatic compartment (including sediment) Table 991. Environmental risk aquatic of ES 112.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.112.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 995. Worker risk of ES 112.3

10.112.4 Contributing Scenario (4) controlling professional worker exposure for PROC

11 Professional Use of Vehicle cleaning Products Car wash product; Spray - Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 996. Worker risk of ES 112.4

10.113 Scenario 113: Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process (AISE-P703a, AISE-P703b) The following RCR calculations refer to the contributing scenarios described in chapter 9.113 10.113.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.113.1.1 Aquatic compartment (including sediment) Table 997. Environmental risk aquatic of ES 113.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.113.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.113.2.1 Aquatic compartment (including sediment) Table 1001. Environmental risk aquatic of ES 113.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.113.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.113.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Vehicle cleaning Products Car wash product; Spray and Wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1006. Worker risk of ES 113.4

10.114 Scenario 114: Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process (AISE-P704a, AISE-P704b) The following RCR calculations refer to the contributing scenarios described in chapter 9.114 10.114.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.114.1.1 Aquatic compartment (including sediment) Table 1007. Environmental risk aquatic of ES 114.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.114.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.114.2.1 Aquatic compartment (including sediment) Table 1011. Environmental risk aquatic of ES 114.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.114.3 Contributing Scenario (3) controlling professional worker exposure for PROC 4 Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1015. Worker risk of ES 114.3

10.114.4 Contributing Scenario (4) controlling professional worker exposure for PROC 4 Professional Use of Vehicle cleaning Products Dewaxing product; Semi-Automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1016. Worker risk of ES 114.4

10.115 Scenario 115: Professional Use of Vehicle cleaning Products Boat cleaner; Manual process (AISE-P705) The following RCR calculations refer to the contributing scenarios described in chapter 9.115 10.115.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Boat cleaner; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.115.1.1 Aquatic compartment (including sediment) Table 1017. Environmental risk aquatic of ES 115.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.115.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10

Professional Use of Vehicle cleaning Products Boat cleaner; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1021. Worker risk of ES 115.2

10.116 Scenario 116: Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process (AISE-P706a, AISE-P706b) The following RCR calculations refer to the contributing scenarios described in chapter 9.116 10.116.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.116.1.1 Aquatic compartment (including sediment) Table 1022. Environmental risk aquatic of ES 116.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.116.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.116.2.1 Aquatic compartment (including sediment) Table 1026. Environmental risk aquatic of ES 116.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.116.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1030. Worker risk of ES 116.3

10.116.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Vehicle cleaning Products Boat cleaner; Spray and wipe manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1031. Worker risk of ES 116.4

10.117 Scenario 117: Professional Use of pharmacos products Animal care; Manual process (AISE-P808) The following RCR calculations refer to the contributing scenarios described in chapter 9.117 10.117.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of pharmacos products Animal care; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.117.1.1 Aquatic compartment (including sediment) Table 1032. Environmental risk aquatic of ES 117.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.117.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of pharmacos products Animal care; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1036. Worker risk of ES 117.2

10.118 Scenario 118: Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process (AISE-P901a, AISE-P901b) The following RCR calculations refer to the contributing scenarios described in chapter 9.118 10.118.1 Contributing Scenario (1) controlling environmental exposure for ERC8D Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.118.1.1 Aquatic compartment (including sediment) Table 1037. Environmental risk aquatic of ES 118.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.118.2 Contributing Scenario (2) controlling environmental exposure for ERC8D Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.118.2.1 Aquatic compartment (including sediment) Table 1041. Environmental risk aquatic of ES 118.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.118.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1045. Worker risk of ES 118.3

10.118.4 Contributing Scenario (4) controlling professional worker exposure for PROC 11 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; High pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1046. Worker risk of ES 118.4

10.119 Scenario 119: Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process (AISE-P902a, AISE-P902b) The following RCR calculations refer to the contributing scenarios described in chapter 9.119 10.119.1 Contributing Scenario (1) controlling environmental exposure for ERC8D Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.119.1.1 Aquatic compartment (including sediment) Table 1047. Environmental risk aquatic of ES 119.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.119.2 Contributing Scenario (2) controlling environmental exposure for ERC8D Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.119.2.1 Aquatic compartment (including sediment) Table 1051. Environmental risk aquatic of ES 119.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.119.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.119.4 Contributing Scenario (4) controlling professional worker exposure for PROC 11 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1056. Worker risk of ES 119.4

10.119.5 Contributing Scenario (5) controlling professional worker exposure for PROC 10 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1057. Worker risk of ES 119.5

10.119.6 Contributing Scenario (6) controlling professional worker exposure for PROC 10 Professional Use of Façade/surface Cleaning Products Façade/surface cleaner; Medium pressure process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable.

10.120 Scenario 120: Professional Use of Medical Devices Medical devices ; Semi-automatic process (AISE-P1101) The following RCR calculations refer to the contributing scenarios described in chapter 9.120 10.120.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Medical Devices Medical devices ; Semi-automatic process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.120.1.1 Aquatic compartment (including sediment) Table 1059. Environmental risk aquatic of ES 120.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.120.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Professional Use of Medical Devices Medical devices ; Semi-automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1063. Worker risk of ES 120.2

10.120.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Professional Use of Medical Devices Medical devices ; Semi-automatic process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1064. Worker risk of ES 120.3

10.121 Scenario 121: Professional Use of Medical Devices Medical devices ; Dipping process (AISE-P1102) The following RCR calculations refer to the contributing scenarios described in chapter 9.121 10.121.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Medical Devices Medical devices ; Dipping process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.121.1.1 Aquatic compartment (including sediment) Table 1065. Environmental risk aquatic of ES 121.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.121.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Professional Use of Medical Devices Medical devices ; Dipping process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1069. Worker risk of ES 121.2

10.122 Scenario 122: Professional Use of Medical Devices Medical devices ; Manual process (AISE-P1103) The following RCR calculations refer to the contributing scenarios described in chapter 9.122 10.122.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Medical Devices Medical devices ; Manual process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

Total 0.003104 15 mg/kgbw/day 0.000207 9,931.113

MSafe kg/d

mg/kgbw/day

10.122.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Professional Use of Medical Devices Medical devices ; Manual process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1074. Worker risk of ES 122.2

10.123 Scenario 123: Professional Use of Medical Devices Medical devices ; Spray and wipe process (AISE-P1104a, AISE-P1104b) The following RCR calculations refer to the contributing scenarios described in chapter 9.123 10.123.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Medical Devices Medical devices ; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.123.1.1 Aquatic compartment (including sediment) Table 1075. Environmental risk aquatic of ES 123.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.123.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Professional Use of Medical Devices Medical devices ; Spray and wipe process The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.123.2.1 Aquatic compartment (including sediment) Table 1079. Environmental risk aquatic of ES 123.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.123.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Professional Use of Medical Devices Medical devices ; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1083. Worker risk of ES 123.3

10.123.4 Contributing Scenario (4) controlling professional worker exposure for PROC 10 Professional Use of Medical Devices Medical devices ; Spray and wipe process The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1084. Worker risk of ES 123.4

10.124 Scenario 124: Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…) (AISE-P1200) The following RCR calculations refer to the contributing scenarios described in chapter 9.124 10.124.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.124.1.1 Aquatic compartment (including sediment) Table 1085. Environmental risk aquatic of ES 124.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.124.2 Contributing Scenario (2) controlling professional worker exposure for PROC 15 Laboratory Use Laboratory Reagents (sampling cleaning product for dosage, pH measurement, titration of chlorine, water hardness, etc…) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1089. Worker risk of ES 124.2

10.125 Scenario 125: Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants (AISE-P1300) The following RCR calculations refer to the contributing scenarios described in chapter 9.125 10.125.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.125.1.1 Aquatic compartment (including sediment) Table 1090. Environmental risk aquatic of ES 125.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.125.2 Contributing Scenario (2) controlling professional worker exposure for PROC 19 Professional Use of Hand Cleaners Professional Hand Cleaner /skin desinfectants The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1094. Worker risk of ES 125.2

10.126 Scenario 126: Transfer of professional cleaning or maintenance

product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) (AISE_CSP01a, AISE_CSP01b) The following RCR calculations refer to the contributing scenarios described in chapter 9.126 10.126.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.126.1.1 Aquatic compartment (including sediment) Table 1095. Environmental risk aquatic of ES 126.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

Root crop 0.000039 15 mg/kgbw/day 2.59E-6 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.126.2 Contributing Scenario (2) controlling environmental exposure for ERC8A Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.126.2.1 Aquatic compartment (including sediment) Table 1099. Environmental risk aquatic of ES 126.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.126.3 Contributing Scenario (3) controlling professional worker exposure for PROC 8A Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1103. Worker risk of ES 126.3

10.126.4 Contributing Scenario (4) controlling professional worker exposure for PROC 8A Transfer of professional cleaning or maintenance product (charging/discharging) to a cleaning equipment (machine/vessel/bucket) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1104. Worker risk of ES 126.4

10.127 Scenario 127: Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment (AISE_CSP02) The following RCR calculations refer to the contributing scenarios described in chapter 9.127 10.127.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.127.1.1 Aquatic compartment (including sediment) Table 1105. Environmental risk aquatic of ES 127.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.127.2 Contributing Scenario (2) controlling professional worker exposure for PROC 8B Transfer of professional cleaning or maintenance product (charging/discharging) to a dedicated cleaning equipment The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1109. Worker risk of ES 127.2

10.128 Scenario 128: Trigger spraying of a professional cleaning or maintenance product during short time. (AISE_CSP03) The following RCR calculations refer to the contributing scenarios described in chapter 9.128 10.128.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Trigger spraying of a professional cleaning or maintenance product during short time. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.128.1.1 Aquatic compartment (including sediment) Table 1110. Environmental risk aquatic of ES 128.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.128.2 Contributing Scenario (2) controlling professional worker exposure for PROC 11 Trigger spraying of a professional cleaning or maintenance product during short time. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1114. Worker risk of ES 128.2

10.129 Scenario 129: Spraying of a professional cleaning or maintenance product (indoor and outdoor) (AISE_CSP04) The following RCR calculations refer to the contributing scenarios described in chapter 9.129 10.129.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Spraying of a professional cleaning or maintenance product (indoor and outdoor) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.129.1.1 Aquatic compartment (including sediment) Table 1115. Environmental risk aquatic of ES 129.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.129.2 Contributing Scenario (2) controlling professional worker exposure for PROC 11 Spraying of a professional cleaning or maintenance product (indoor and outdoor) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1119. Worker risk of ES 129.2

10.129.3 Contributing Scenario (3) controlling professional worker exposure for PROC 11 Spraying of a professional cleaning or maintenance product (indoor and outdoor) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1120. Worker risk of ES 129.3

10.130 Scenario 130: Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment (AISE_CSP05) The following RCR calculations refer to the contributing scenarios described in chapter 9.130 10.130.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.130.1.1 Aquatic compartment (including sediment) Table 1121. Environmental risk aquatic of ES 130.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.130.2 Contributing Scenario (2) controlling professional worker exposure for PROC 1 Using a diluted professional cleaning solution or maintenance product in a closed cleaning equipment The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1125. Worker risk of ES 130.2

10.131 Scenario 131: Using a diluted professional cleaning solution in a semi closed cleaning equipment (AISE_CSP06) The following RCR calculations refer to the contributing scenarios described in chapter 9.131 10.131.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Using a diluted professional cleaning solution in a semi closed cleaning equipment The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.131.1.1 Aquatic compartment (including sediment) Table 1126. Environmental risk aquatic of ES 131.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.131.2 Contributing Scenario (2) controlling professional worker exposure for PROC 2 Using a diluted professional cleaning solution in a semi closed cleaning equipment The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1130. Worker risk of ES 131.2

10.132 Scenario 132: Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure

arises (AISE_CSP07) The following RCR calculations refer to the contributing scenarios described in chapter 9.132 10.132.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure arises The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.132.1.1 Aquatic compartment (including sediment) Table 1131. Environmental risk aquatic of ES 132.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.132.2 Contributing Scenario (2) controlling professional worker exposure for PROC 4 Using a diluted professional cleaning solution or maintenance product in a cleaning equipment; opportunity for exposure arises The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1135. Worker risk of ES 132.2

10.133 Scenario 133: Brushing a diluted professional cleaning solution, desinfectant or maintenance product (AISE_CSP08) The following RCR calculations refer to the contributing scenarios described in chapter 9.133 10.133.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Brushing a diluted professional cleaning solution, desinfectant or maintenance product The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.133.1.1 Aquatic compartment (including sediment) Table 1136. Environmental risk aquatic of ES 133.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.133.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Brushing a diluted professional cleaning solution, desinfectant or maintenance product The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1140. Worker risk of ES 133.2

10.134 Scenario 134: Brushing a professional cleaning or maintenance product after trigger spraying (AISE_CSP09) The following RCR calculations refer to the contributing scenarios described in chapter 9.134 10.134.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Brushing a professional cleaning or maintenance product after trigger spraying The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.134.1.1 Aquatic compartment (including sediment) Table 1141. Environmental risk aquatic of ES 134.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.134.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Brushing a professional cleaning or maintenance product after trigger spraying The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1145. Worker risk of ES 134.2

10.135 Scenario 135: Brushing a concentrated professional cleaning or

maintenance product. (AISE-CSP10) The following RCR calculations refer to the contributing scenarios described in chapter 9.135 10.135.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Brushing a concentrated professional cleaning or maintenance product. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.135.1.1 Aquatic compartment (including sediment) Table 1146. Environmental risk aquatic of ES 135.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.135.2 Contributing Scenario (2) controlling professional worker exposure for PROC 10 Brushing a concentrated professional cleaning or maintenance product. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1150. Worker risk of ES 135.2

10.136 Scenario 136: Treatment of articles by dipping or pouring with a professional cleaning or maintenance products (AISE_CSP11) The following RCR calculations refer to the contributing scenarios described in chapter 9.136 10.136.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Treatment of articles by dipping or pouring with a professional cleaning or maintenance products The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.136.1.1 Aquatic compartment (including sediment) Table 1151. Environmental risk aquatic of ES 136.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.136.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Treatment of articles by dipping or pouring with a professional cleaning or maintenance products The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1155. Worker risk of ES 136.2

10.137 Scenario 137: Professional Use of Drain Unblockers (AISE_CSP12) The following RCR calculations refer to the contributing scenarios described in chapter 9.137 10.137.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Professional Use of Drain Unblockers The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.137.1.1 Aquatic compartment (including sediment) Table 1156. Environmental risk aquatic of ES 137.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.137.2 Contributing Scenario (2) controlling professional worker exposure for PROC 13 Professional Use of Drain Unblockers The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1160. Worker risk of ES 137.2

10.138 Scenario 138: Laboratory use of Cleaning and Maintenance

products (AISE_CSP13) The following RCR calculations refer to the contributing scenarios described in chapter 9.138 10.138.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Laboratory use of Cleaning and Maintenance products The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.138.1.1 Aquatic compartment (including sediment) Table 1161. Environmental risk aquatic of ES 138.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.138.2 Contributing Scenario (2) controlling professional worker exposure for PROC 15 Laboratory use of Cleaning and Maintenance products The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1165. Worker risk of ES 138.2

10.139 Scenario 139: Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use (AISE C1) The following RCR calculations refer to the contributing scenarios described in chapter 9.139 10.139.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.139.1.1 Aquatic compartment (including sediment) Table 1166. Environmental risk aquatic of ES 139.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.139.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products LAUNDRY REGULAR (powder, liquid) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1170. Consumer risk of ES 139.2

dermal long-term systemic 61.082 mg/kgbw/day 1,650 mg/kgbw/day 0.03702

inhalation long-term systemic 13.356 mg/m3 52 mg/m3 0.256849

oral - - -

10.140 Scenario 140: Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use (AISE C2) The following RCR calculations refer to the contributing scenarios described in chapter 9.140 10.140.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.140.1.1 Aquatic compartment (including sediment) Table 1171. Environmental risk aquatic of ES 140.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.140.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products LAUNDRY COMPACT (powder, liquid/gel, tablet) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1175. Consumer risk of ES 140.2

oral - - -

10.141 Scenario 141: Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use (AISE C3) The following RCR calculations refer to the contributing scenarios described in chapter 9.141 10.141.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.141.1.1 Aquatic compartment (including sediment) Table 1176. Environmental risk aquatic of ES 141.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.141.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products FABRIC CONDITIONERS (liquid regular, liquid concentrate) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1180. Consumer risk of ES 141.2

oral - - -

10.142 Scenario 142: Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use (AISE C4) The following RCR calculations refer to the contributing scenarios described in chapter 9.142 10.142.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.142.2 Contributing Scenario (2) controlling environmental exposure for ERC8B Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.142.2.1 Aquatic compartment (including sediment) Table 1185. Environmental risk aquatic of ES 142.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.142.3 Contributing Scenario (3) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products LAUNDRY ADDITIVES (powder bleach, liquid bleach, tablet) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1189. Consumer risk of ES 142.3

oral - - -

10.143 Scenario 143: Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use (AISE C5) The following RCR calculations refer to the contributing scenarios described in chapter 9.143 10.143.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.143.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products HAND DISHWASHING (liquid regular, liquid concentrate) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1194. Consumer risk of ES 143.2

oral - - -

10.144 Scenario 144: Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use (AISE C6) The following RCR calculations refer to the contributing scenarios described in chapter 9.144 10.144.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.144.1.1 Aquatic compartment (including sediment) Table 1195. Environmental risk aquatic of ES 144.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.144.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products MACHINE DISHWASHING (powder, liquid, tablet) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model.

The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1199. Consumer risk of ES 144.2

oral - - -

10.145 Scenario 145: Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use (AISE C7) The following RCR calculations refer to the contributing scenarios described in chapter 9.145 10.145.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.145.1.1 Aquatic compartment (including sediment) Table 1200. Environmental risk aquatic of ES 145.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.145.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products SURFACE CLEANERS (liquid, powder, gel neat, spray neat) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1204. Consumer risk of ES 145.2

oral - - -

10.146 Scenario 146: Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use (AISE C8)

The following RCR calculations refer to the contributing scenarios described in chapter 9.146 10.146.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.146.1.1 Aquatic compartment (including sediment) Table 1205. Environmental risk aquatic of ES 146.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.146.2 Contributing Scenario (2) controlling environmental exposure for ERC8B Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.146.2.1 Aquatic compartment (including sediment) Table 1209. Environmental risk aquatic of ES 146.2

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.146.3 Contributing Scenario (3) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products TOILET CLEANERS (powder, liquid, gel, tablet) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1213. Consumer risk of ES 146.3

oral - - -

10.147 Scenario 147: Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use (AISE C9) The following RCR calculations refer to the contributing scenarios described in chapter 9.147

10.147.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.147.1.1 Aquatic compartment (including sediment) Table 1214. Environmental risk aquatic of ES 147.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.147.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products WATER SOFTENERS (powder, liquids, Tabs) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1218. Consumer risk of ES 147.2

oral - - -

10.148 Scenario 148: Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use (AISE C10) The following RCR calculations refer to the contributing scenarios described in chapter 9.148 10.148.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.148.1.1 Aquatic compartment (including sediment) Table 1219. Environmental risk aquatic of ES 148.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.148.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products OVEN CLEANERS (spray, trigger) for consumer use

The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1223. Consumer risk of ES 148.2

oral - - -

10.149 Scenario 149: Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use (AISE C11) The following RCR calculations refer to the contributing scenarios described in chapter 9.149 10.149.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.149.1.1 Aquatic compartment (including sediment) Table 1224. Environmental risk aquatic of ES 149.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.149.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products CARPET CLEANERS (spray, liquid) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1228. Consumer risk of ES 149.2

oral - - -

10.150 Scenario 150: Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use (AISE C12)

The following RCR calculations refer to the contributing scenarios described in chapter 9.150 10.150.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.150.1.1 Aquatic compartment (including sediment) Table 1229. Environmental risk aquatic of ES 150.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.150.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products LAUNDRY AIDS (ironing aids-starch spray, ironing aids-other) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1233. Consumer risk of ES 150.2

oral - - -

10.151 Scenario 151: Consumer use of washing and cleaning products DRAIN PRODUCTS (powder, gel) (AISE C13) The following RCR calculations refer to the contributing scenarios described in chapter 9.151 10.151.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products DRAIN PRODUCTS (powder, gel) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.151.1.1 Aquatic compartment (including sediment) Table 1234. Environmental risk aquatic of ES 151.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.151.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products DRAIN PRODUCTS (powder, gel) The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1238. Consumer risk of ES 151.2

oral - - -

10.152 Scenario 152: Consumer use of washing and cleaning products DESCALERS (AISE C14) The following RCR calculations refer to the contributing scenarios described in chapter 9.152 10.152.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products DESCALERS The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.152.1.1 Aquatic compartment (including sediment) Table 1239. Environmental risk aquatic of ES 152.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.152.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products DESCALERS The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1243. Consumer risk of ES 152.2

oral - - -

10.153 Scenario 153: Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use (AISE C15) The following RCR calculations refer to the contributing scenarios described in chapter 9.153 10.153.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.153.1.1 Aquatic compartment (including sediment) Table 1244. Environmental risk aquatic of ES 153.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.153.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products WIPES (bathroom, kitchen, floor) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1248. Consumer risk of ES 153.2

oral - - -

10.154 Scenario 154: Consumer use of washing and cleaning products High Pressure washers/cleaners (AISE C21) The following RCR calculations refer to the contributing scenarios described in chapter 9.154 10.154.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products High Pressure washers/cleaners The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.154.1.1 Aquatic compartment (including sediment) Table 1249. Environmental risk aquatic of ES 154.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.154.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products High Pressure washers/cleaners The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1253. Consumer risk of ES 154.2

oral - - -

10.155 Scenario 155: Consumer use of washing and cleaning products Automotive Care (spray, liquid) (AISE C22) The following RCR calculations refer to the contributing scenarios described in chapter 9.155 10.155.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of washing and cleaning products Automotive Care (spray, liquid) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.155.1.1 Aquatic compartment (including sediment) Table 1254. Environmental risk aquatic of ES 155.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.155.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of washing and cleaning products Automotive Care (spray, liquid) The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1258. Consumer risk of ES 155.2

oral - - -

10.156 Scenario 156: AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use (AISE C17) The following RCR calculations refer to the contributing scenarios described in chapter 9.156 10.156.1 Contributing Scenario (1) controlling environmental exposure for ERC8A AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.156.1.1 Aquatic compartment (including sediment) Table 1259. Environmental risk aquatic of ES 156.1

MSafe kg/d

STP 0 mg/L 1.00E4 mg/L 0 ∞

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.156.2 Contributing Scenario (2) controlling consumer exposure for PC 3 AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use AIR FRESHENERS AEROSOL (aqueous, non aqueous, concentrated (mini-aerosol)Timed-release aerosols) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1263. Consumer risk of ES 156.2

dermal - - -

oral - - -

10.157 Scenario 157: AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use (AISE C18) The following RCR calculations refer to the contributing scenarios described in chapter 9.157 10.157.1 Contributing Scenario (1) controlling environmental exposure for ERC8A AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for

consumer use The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.157.1.1 Aquatic compartment (including sediment) Table 1264. Environmental risk aquatic of ES 157.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

MSafe kg/d

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.157.2 Contributing Scenario (2) controlling consumer exposure for PC 3 AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use AIR FRESHENERS NON AEROSOL (Perfume in/on solid substarte (gel), candles, diffusers (heated) for consumer use The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1268. Consumer risk of ES 157.2

oral - - -

10.158 Scenario 158: Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants (AISE C19a) The following RCR calculations refer to the contributing scenarios described in chapter 9.158 10.158.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.158.1.1 Aquatic compartment (including sediment) Table 1269. Environmental risk aquatic of ES 158.1

MSafe kg/d

STP 0 mg/L 1.00E4 mg/L 0 ∞

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.158.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, propellants The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1273. Consumer risk of ES 158.2

oral - - -

10.159 Scenario 159: Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants (AISE C19b) The following RCR calculations refer to the contributing scenarios described in chapter 9.159 10.159.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.159.1.1 Aquatic compartment (including sediment) Table 1274. Environmental risk aquatic of ES 159.1

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.159.2 Contributing Scenario (2) controlling consumer exposure for PC 35 Consumer use of pest control products INSECTICIDES (liquid electric, spray neat) and REPELLENTS for consumer use, non-propellants The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1278. Consumer risk of ES 159.2

oral - - -

10.160 Scenario 160: Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants (AISE C20a) The following RCR calculations refer to the contributing scenarios described in chapter 9.160 10.160.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.160.1.1 Aquatic compartment (including sediment) Table 1279. Environmental risk aquatic of ES 160.1

MSafe kg/d

STP 0 mg/L 1.00E4 mg/L 0 ∞

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 9,931.113

10.160.2 Contributing Scenario (2) controlling consumer exposure for PC 31 Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, propellants The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1283. Consumer risk of ES 160.2

oral - - -

10.161 Scenario 161: Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants (AISE C20b) The following RCR calculations refer to the contributing scenarios described in chapter 9.161 10.161.1 Contributing Scenario (1) controlling environmental exposure for ERC8A Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.018209 mg/L 1.00E4 mg/L 1.82E-6 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 9,931.113

10.161.2 Contributing Scenario (2) controlling consumer exposure for PC 31 Consumer use of polishes FURNITURE FLOOR & LEATHER CARE (spray, liquid) for consumer use, non-propellants The quantitative risk characterisation for this consumer exposure has been calculated by EasyTRA using the Ecetoc TRA calculation model. The following table shows the exposure estimations via the oral, dermal and inhalatory route together with the total exposure of consumers over all routes if applicable. Table 1288. Consumer risk of ES 161.2

oral - - -

10.162 Scenario 162: Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) (AISE_CS_I01a, AISE_CS_I01b) The following RCR calculations refer to the contributing scenarios described in chapter 9.162 10.162.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.162.1.1 Aquatic compartment (including sediment) Table 1289. Environmental risk aquatic of ES 162.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.162.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

mg/kgbw/day

15 mg/kgbw/day 0.000207 2.42E5

10.162.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 8B Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1297. Worker risk of ES 162.3

10.162.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 8B Transfer of industrial detergent, maintenance or desinfectant (charging/discharging) to a dedicated cleaning equipment (machine/vessel) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1298. Worker risk of ES 162.4

10.163 Scenario 163: Using a diluted industrial cleaning solution in a closed cleaning equipment (AISE_CS_I02) The following RCR calculations refer to the contributing scenarios described in chapter 9.163 10.163.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Using a diluted industrial cleaning solution in a closed cleaning equipment The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA.

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

MSafe kg/d

15 mg/kgbw/day 0.000207 2.42E5

10.163.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 1 Using a diluted industrial cleaning solution in a closed cleaning equipment The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1303. Worker risk of ES 163.2

10.164 Scenario 164: Using a diluted industrial cleaning solution in a semi closed cleaning equipment (AISE_CS_I03) The following RCR calculations refer to the contributing scenarios described in chapter 9.164 10.164.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Using a diluted industrial cleaning solution in a semi closed cleaning equipment The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.164.1.1 Aquatic compartment (including sediment) Table 1304. Environmental risk aquatic of ES 164.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.164.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 2 Using a diluted industrial cleaning solution in a semi closed cleaning equipment The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1308. Worker risk of ES 164.2

10.165 Scenario 165: Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises (AISE_CS_I04a, AISE_CS_I04b) The following RCR calculations refer to the contributing scenarios described in chapter 9.165 10.165.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.165.1.1 Aquatic compartment (including sediment) Table 1309. Environmental risk aquatic of ES 165.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.165.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.165.2.1 Aquatic compartment (including sediment) Table 1313. Environmental risk aquatic of ES 165.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.165.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 4 Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1317. Worker risk of ES 165.3

10.165.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 4 Using a diluted industrial cleaning, desinfectant or maintenance product in an dedicated equipment; opportunity for exposure arises The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1318. Worker risk of ES 165.4

10.166 Scenario 166: Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. (AISE_CS_I05a, AISE_CS_I05b) The following RCR calculations refer to the contributing scenarios described in chapter 9.166 10.166.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.166.1.1 Aquatic compartment (including sediment) Table 1319. Environmental risk aquatic of ES 166.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.166.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.166.2.1 Aquatic compartment (including sediment) Table 1323. Environmental risk aquatic of ES 166.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.166.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 7 Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1327. Worker risk of ES 166.3

10.166.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 7 Pressure spraying of a diluted industrial cleaning, desinfectant or maintenance product. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1328. Worker risk of ES 166.4

10.167 Scenario 167: Spraying of a diluted industrial cleaning or maintenance product during short time. (AISE_CS_I06) The following RCR calculations refer to the contributing scenarios described in chapter 9.167 10.167.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Spraying of a diluted industrial cleaning or maintenance product during short time. The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.167.1.1 Aquatic compartment (including sediment) Table 1329. Environmental risk aquatic of ES 167.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.167.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 7 Spraying of a diluted industrial cleaning or maintenance product during short time. The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1333. Worker risk of ES 167.2

10.168 Scenario 168: Brushing an industrial cleaning solution (AISE_CS_I07a, AISE_CS_I07b) The following RCR calculations refer to the contributing scenarios described in chapter 9.168 10.168.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Brushing an industrial cleaning solution The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.168.1.1 Aquatic compartment (including sediment) Table 1334. Environmental risk aquatic of ES 168.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.168.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Brushing an industrial cleaning solution The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.168.2.1 Aquatic compartment (including sediment) Table 1338. Environmental risk aquatic of ES 168.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.168.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 10 Brushing an industrial cleaning solution The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1342. Worker risk of ES 168.3

10.168.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 10 Brushing an industrial cleaning solution

10.169 Scenario 169: Brushing a diluted cleaning or maintenance product (after spraying) (AISE_CS_I08a, AISE_CS_I08b) The following RCR calculations refer to the contributing scenarios described in chapter 9.169 10.169.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Brushing a diluted cleaning or maintenance product (after spraying) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.169.1.1 Aquatic compartment (including sediment) Table 1344. Environmental risk aquatic of ES 169.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.169.2 Contributing Scenario (2) controlling environmental exposure for ERC4 Brushing a diluted cleaning or maintenance product (after spraying) The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.169.2.1 Aquatic compartment (including sediment) Table 1348. Environmental risk aquatic of ES 169.2

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.169.3 Contributing Scenario (3) controlling industrial worker exposure for PROC 10 Brushing a diluted cleaning or maintenance product (after spraying) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1352. Worker risk of ES 169.3

10.169.4 Contributing Scenario (4) controlling industrial worker exposure for PROC 10 Brushing a diluted cleaning or maintenance product (after spraying) The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1353. Worker risk of ES 169.4

10.170 Scenario 170: Treatment of articles by dipping or pouring with an industrial cleaning product (AISE_CS_I09) The following RCR calculations refer to the contributing scenarios described in chapter 9.170 10.170.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Treatment of articles by dipping or pouring with an industrial cleaning product The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.170.1.1 Aquatic compartment (including sediment) Table 1354. Environmental risk aquatic of ES 170.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.170.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 13 Treatment of articles by dipping or pouring with an industrial cleaning product The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1358. Worker risk of ES 170.2

10.171 Scenario 171: Quality control on industrial cleaning, desinfectants and maintenance Products (AISE_CS_I10) The following RCR calculations refer to the contributing scenarios described in chapter 9.171 10.171.1 Contributing Scenario (1) controlling environmental exposure for ERC4 Quality control on industrial cleaning, desinfectants and maintenance Products The quantitative risk characterisation for this environmental exposure has been calculated using EasyTRA. The environmental exposure calculation per compartment is based on the algorithms of the EU TGD 2003 Risk Assessment Spreadsheet Model 1.24a. 10.171.1.1 Aquatic compartment (including sediment) Table 1359. Environmental risk aquatic of ES 171.1

MSafe kg/d

STP 0.443083 mg/L 1.00E4 mg/L 0.000044 1.13E6

MSafe kg/d

15 mg/kgbw/day 0.000125 -

15 mg/kgbw/day 0.00007 -

15 mg/kgbw/day 0.000207 2.42E5

10.171.2 Contributing Scenario (2) controlling industrial worker exposure for PROC 15 Quality control on industrial cleaning, desinfectants and maintenance Products The quantitative risk characterisation for this worker exposure has been calculated by EasyTRA. The following table shows the exposure estimations via the dermal and inhalatory route together with the total exposure of workers over all routes if applicable. Table 1363. Worker risk of ES 171.2

9. exposure assessment - clariant · 9. exposure assessment qualitative csa - skin irritation and...

Documents

biocidi clariant

superfund exposure assessment manual - the risk assessment

guidance on the assessment of exposure for operators ... ·...

guidelines for exposure assessment

toxicology - exposure assessment

clariant story 2018 - swiss equities conference€¦ · 2...

1. sources, exposure and exposure assessment

clariant micronized waxes

clariant antistatic agents

vibration exposure assessment for industrial power … ·...

clariant solutions services

chapter 6: dermal exposure assessment - oehha · pdf...

clariant fr

exposure assessment: establishing similar exposure groups

pbt assessment & category approach - reach -...

aditivos clariant

brochure substante clariant

clariant report

human exposure assessment and risk assessment (part...

chapter 4 exposure assessment strategies …€¦ · 4-1...