a ssc pattern
Post on 14-Jan-2016
8 Views
Preview:
DESCRIPTION
TRANSCRIPT
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 1/19
1
Soft Structured Carrier
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 2/19
2
Symbol Key
Place Pattern on Fold
Add/Subtract Length
Grain line for Patterned
fabric
Reinforced
X-Box Stitching
Strap Placement
Top-stitching
Line up to Sew Darts
Line up Pattern pieces
Line up Shoulder Strap
Placement
D-ring Placement
Top-stitching
Lines of note, but which are
not sewn
A
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 3/19
3
Safety Considerations!You will be using this to carry precious cargo, so be sure to use only good quality materials. Fabricsshould all be bottom-weight (like one would use for pants). If you hold them up to the light, you should
not see very much light through them. Canvas, denim, heavy twill, some hemp fabrics, etc., of at least 8
oz are safe. Corduroy should be reinforced with another heavy fabric at all weight bearing connections
because it has been known to tear under stress. Make sure all weight-bearing seams have at least 3 rowsof stitching; in this case more is more. When using the carrier always keep an eye out for strain in thefabric and seams. Check your carrier before every use for loose threads, worn fabric, broken buckles, etc.
Listen for ‘popping’ sounds when you put your carrier on, and check the stitching if you hear any such
sounds. Buy your buckles and webbing carefully and make sure they have a sufficient weight rating.
Buy only buckles from specialized camping stores, or similar places, which are meant to carry heavy
loads. Be aware that sewing on a home machine will never be as strong or dependable as sewing on anindustrial machine, and so don’t expect your carrier to be as durable or long-lasting as many
professionally made SSCs.
The creators of this pattern and instructions are cannot be held responsible
for inappropriate use of the finished carrier. Nor are they responsible for bad
choices in materials, faulty sewing, or failure of the carrier in any way due toconstruction techniques. These directions are just suggested, and it is up to
every sewer’s discretion to follow them and sew the carrier in a safe fashion.
SuppliesFabric:
• Waist belt: You need a piece of fabric about 24" x 36"
• Shoulder straps you need a 16" x 26" piece
• Body: each piece (as shown in pattern) will fit on a fat quarter. 18" x 22" so for three layers you
will need 3 fat quarters or one yard of fabric
Webbing:
• 2' of 2" polypropylene webbing for waist,
• 4' of 1.5" polypropylene webbing for the shoulder straps.
• One 2" single adjust clip for the waist
• Two 1.5" single adjust clips for the shoulders.
• Optional is 1' of 3/4" and one 3/4" clip for a chest strap
• Two 1” D-rings
Padding:
• two pieces of 16x13" fleece plus some small pieces for the shoulder straps
•
high density foam about 1/2" thick for the waist you will need a piece at least 24"x33"x1/4”.Some people use a cheap camping pad or a double layer of yoga mat
Fabric recommendations:
Straps:
• Canvas or twill also make good straps, especially if they are brushed or laundered.
• Both layers should be a sturdy fabric
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 4/19
4
Body:
• Either a hidden panel of 10+ oz. fabric with lining and decorative panel.• Or two layers of bottom weight fabric such as twill, cord, denim or canvas with an optional inner lining or
outer decorative panel.
Directions
Use 1/2” seams unless otherwise indicated.
Use a larger/heavyweight needle, at least 90/12.
Use good quality thread
Use a fairly small straight stitch (2-2.5 on most machines).
Go slowly over thick layers using hand wheel if necessary to help the machine along and allow the
machine to feed for itself, do not pull/push, to avoid broken needles.
For extra durability you can, zig zag stitch, or serge, the edges around all of your pattern pieces to preventfraying inside the finished SSC but it isn't necessary.
Assembly
Assemble the Straight Shoulder straps:
1. Assemble shoulder strap pattern and place on fold as indicated. Cut two pieces.
2. Cut two 13” by 16” pieces of fleece and fold into four layers lengthwise, final size about 3.5” x
16”
a. If you are adding a hood attach the D-ring to one layer of the shoulder strap using either a
short piece of webbing or a length of hemmed fabric (see pattern)
3.
Fold over 1/2” and sew the tapered end (hem).
4. Cut two 2” pieces of 1.5” webbing and use them to attach the female half of the 1.5” buckles to
one layer of the tapered end with a single line of stitching.
5. Fold over the strap pieces lengthwise, right sides together and sew lengthwise stopping at the
tapered end.
6.
Turn right side out.
7. Insert the fleece into the tube of the shoulder strap, leaving 5-6” unpadded at the top.
8. Make sure the fleece is laying flat and top stitch down the middle lengthwise start/stopping about
1” into the fleece
9.
Top stitch the tapered ends closed and finish attaching the webbing, using re-enforced (x-box)
stitching to secure the webbing.
OR
Assemble the Curved Shoulder straps:
1.
Assemble shoulder strap pattern and cut four pieces.a. If you are adding a hood attach the D-ring to one layer of the shoulder strap using either a
short piece of webbing or a length of hemmed fabric (see pattern)
2.
Cut four layers of fleece padding. Use the inner outline (sewing dotted line) as the pattern piece
for the fleece.
3. Sew the tapered end (hem).
4. Cut two 2” pieces of 1.5” webbing and use them to attach the female half of the 1.5” buckles to
one layer of the tapered end with a single line of stitching.
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 5/19
5
5.
Pin together the strap pieces lengthwise, right sides together and sew lengthwise stopping at the
tapered end.
6. Turn right side out.
7. Insert the fleece into the tube of the shoulder strap, leaving 5-6” unpadded at the top.
8. Make sure the fleece is laying flat and top stitch down the middle lengthwise start/stopping about1” into the fleece
9.
Top stitch the tapered ends closed and finish attaching the webbing, using re-enforced (x-box)stitching to secure the webbing.
Assemble the Hood:1.
Assemble hood pattern, and cut two pieces.
2.
Create hood ties by sewing bias tape closed, or creating your own bias tape cord.
3. Lay out one hood piece, right side up. Lay hood ties over hood, with one end at the bottom of
each side of the hood. The hood ties should be laid out over top of the hood piece. Place the
other hood piece, right side down, over top.4.
Pin edges together, and sew around outside (make sure you ‘catch’ the ends of the hood ties),
leaving the top un-sewn.
5. Turn the hood right side out, through the portion you left open at the top.
Assemble the Body:
1. Assemble body pattern and cut out 3 body pieces laying the pattern along the fold as indicated.
2.
Sew the darts on each piece
3.
Attach the shoulder straps and hood, as illustrated, on the center layer.
4. Cut the remaining 1.5” webbing in half, melt ends and attach as illustrated
5. Place the outside layer on top of the middle layer right side up
6. Place the inner lay on top of that right side down.
7.
Pin the three layers together
8.
Sew around the edge of the three layers, do not sew the bottom or over the four straps
9. Turn right side out and pull the straps through.
10. Topstitch around the edge, turning under the edges around the straps.
Assemble the waist belt:
1.
Assemble the waist belt pattern and cut out the padding and fabric according to instructions.
2. Cut one 6” piece of 2” webbing, melt the ends and use it to attach the female end of the buckle on
one end of one waist piece where indicated on the “right” side
3. Attach the remaining 18” of 2” webbing to the other end of the same piece where indicated on the
“right” side.
4.
Attach the body, inner lining to the wrong side of the other waist piece overlapping 2” as
indicated, with two lines of stitching, 1/4” from the bottom edge of the body and an x-box on
each end
5. sew the two waist pieces right sides together except where the body is
6.
Turn right side out
7.
Insert the padding, if using batting or fleece place on the inner side.8. Tuck in the edges and topstitch along the waist strap where the body overlaps the body.
Buckles:
1.
Clip the male portion of the buckles into the female
2.
Thread the webbing through the male end. You are done.
Optional chest belt:
1. Make sure both ends of the 3/4” webbing are melted.
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 6/19
6
2.
Sew the female half to one end overlapping about 1”
3.
Clip the male half in and thread.
Go try it out!
If you find any inconsistencies or errors in the suggested construction techniques, or the
pattern pieces, please send us an email @ so we can update the pattern.
Creative Commons Attribution-Noncommercial-No Derivative Works 3.0 United States
License
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 7/19
7
T o t a l
f i ni s h e d h e i gh t : 1 6 ”
F i ni s h
e d wi d t h : 1 4 ”
A d d w
i d t h a t f ol d .
A
B
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 8/19
8
C
D
A d d or s u b t r a c t l e n g t h h e r e
A
B
C u t 3
1 –i nn e r p an e l f a b r i c
1 –
o u t e r p an e l d e c or a t i v e f a b
r i c
1 – c
e n t e r p an e l s u p p or t i v e f a
b r i c
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 9/19
9
O v e r l a p wi t h w a i s t t ol i n e
C
D
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 10/19
10
W X
Assemble pattern as
pictured.
Cut 2 on the fold
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 11/19
11
U s e t h i s
pi e c e t o a t t a c h t h e D-r i n g t o
t h e s t r a p
–B e f or e y o u s e w t h e s t r a p s
u p .
C u t 2
W X
Y Z
Add or subtract length here
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 12/19
12
Y Z
Empty unpadded area
between body and
beginning of strappadding.
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 13/19
13
E
F
D o t t e d l i n e
f o r p l a c e m e n t o f f e m a l e b u c k l e
s t r a p
D o u b l e l i n e
f o r p l a c e m e n t o f m a l e b u c k l e ’ s
s t r a p
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 14/19
14
T h i s i s t h
e e x c e s s f a b r i c w h i c h a l l o w s y o u t o
a t t a c h t h e
b o d y t o t h e w a i s t b e l t .
C u t 2 –
F a b r i c
C u t 1 – P
a d d i n g
D o t t e d l i n e f o r s i z e o f
p a d d i n g p i e c e , a s
w e l l a s w h e r e t o s e w f
a b r i c t o g e t h e r .
S o l i d d a r k l i n e f o r c u t t i n g f a b r i c p i e c e s .
F
E
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 15/19
15
Empty unpadded area betweenbody and beginning of strappadding.
L M
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 16/19
16
Cut 4 Strap Pieces
Use this piece to attach the D-ring to
the strap – Before you sew the straps
up.
Cut 2
ON
ML
Add or subtract length here
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 17/19
17
N O
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 18/19
18
Cut 2 Pieces
Lengthen or shorten here
R S
7/18/2019 A SSC Pattern
http://slidepdf.com/reader/full/a-ssc-pattern 19/19
19
S
Ties attach
Here
R
top related