a study of electromechanical behavior of piezo ceramic smart materials and application of piezo...
Post on 30-Jun-2015
938 Views
Preview:
TRANSCRIPT
A Study of electromechanical behavior of Piezo ceramic Smart materials and
application of Piezo ceramic (PZT) for vibration alerts in mobile phones.
Dheepan T, Arun Prasad S
VI semester B. E. Manufacturing Engineering, College of Engineering, Anna University, Guindy,
Chennai-25.
Abstract:
Advances in material science have opened up exciting possibilities for creating novel devices
and structures which respond in safe, effective and speedy manners to changing environmental
and operational conditions. Smart materials and structures is a new field that is being cited as one
of the key technologies for the 21st Century. Typically these SMART materials exploit the
coupling of elasto mechanics and fluid mechanics with electro-physical influences such as piezo-
electric effects, magnetostrictive effects. While millimeter and larger scale devices based on such
principles are beginning to find their way into consumer products, prospects for miniaturization
and micro-miniaturization are emerging that further widen the area of applicability of these smart
materials. As these materials become increasingly smaller for the next generation of smart
materials systems, the need to understand and predict material response becomes critical. This
paper mainly focuses on the study of electro mechanical behavior of piezo ceramic crystals and
designing a basic circuit for incorporating Piezo ceramic (PZT) in vibration alerts in mobile
phones. ’Low battery’ is common term among mobile users ,by applying this smart material
based systems(SMBS) to mobile phones substantial amount of battery will be saved.
Piezo ceramic PZT is a universally acclaimed smart material - which produces motion by
receiving electric potential across their polarized surfaces. Strain output is directly proportional
to the input potential and optimal vibration sense is possible with minimal power consumption.
A basic circuit comprising of receiver, comparator, PZT ceramic, amplifiers is designed to
incorporate the PZT in mobile phone vibration system. The resonant frequency of the ceramic is
too high, so a metal plate (substrate) must be placed along with the ceramic that vibrates with the
contraction and expansion of the piezo ceramic. Metal substrate aids the desired strain transfer
process. This application using smart material can be effectively used in a mobile phone
replacing classic motor operated vibration and since it’s a miniature device it can also be
extended to wrist watch (with some changes in circuit) as a low power consumption vibration
alerts.
Key words: Smart material, Piezo ceramic PZT, Resonant frequency.
1
INTRODUCTION:
The field of smart materials is catching up slowly. Though it’s not as famous as nanotechnology
these materials have their own venture in multifaceted sectors. Potential applications are
aerospace structure monitoring systems, automotive monitoring and control devices, fluid control
devices, biomedical equipment, manufacturing process monitoring devices. Today’s people
admire automations and miniaturizations. Smart material based systems which combines sensor
and actuators is the key technology to achieve this at optimal cost, through system integration
and compact design, systems with less complexity, lower cost, and higher reliability .In this
paper we have studied the electro mechanical behavior of the piezo ceramic smart material and
we designed a basic circuit for employing this smart material in vibration alerts in mobile
phones.
SMART MATERIALS -DEFINITIONS:
Materials that respond with a significant change in a property upon application of
external driving forces.
Smart materials respond to differences in light or temperature. They sense conditions in
their environment and respond to them.
Smart materials are materials which can respond and change their properties depending
upon sensing external factors such as Temperature, Current flow and Light levels.
TYPES OF SMART MATERIALS:
Property Actuators Driving energy
Shape memory Nitinol T , S
2
Piezoelectric PZT,PVDF E,S
Magnetostriction Tetrofenol –D H
T - Thermal energy, E- electrical field S- mechanical strain H – magnetic field;
PIEZOELECTRICITY:
Piezoelectricity, discovered in on Rochelle salt 1880 by the brothers Jacques and Pierre
Curie is defined as a change in electric polarization. Historically, Rochelle salt and quartz are the
most frequently used piezoelectric materials.
The most popular material systems being used for sensors and actuators are piezoelectric
materials, magnetostrictive materials, shape memory alloys, electrorheological fluids and optical
fibers. Magnetostrictive materials, shape memory alloys and electrorheological fluids are used as
actuator materials. Among all these active materials, piezoelectric materials are most widely used
because of their fast electromechanical response, low power requirements and relatively high
generative forces.
PIEZOELECTRIC BEHAVIOR CAN BE MANIFESTED IN TWO DIFFERENT WAYS:
Direct piezoelectric effect: Occurs when piezoelectric crystal is electrically charged when
subjected to mechanical stress. These devices can be used to detect the strain, movement, force,
pressure, vibration by developing appropriate electrical responses, as in case in the case of
ultrasonic and acoustic sensors.
Converse piezoelectric effect: Occurs when piezoelectric crystal is strained when placed in an
electric field .These property can be used to generate strain, force, and vibration by application.
3
PZT – THE SUITABLE PIEZOELECTRIC CERAMIC FOR A MOBILE PHONE
VIBRATION ALERT
Let us study the basic properties of PZT
Lead zirconate titanate,PZT is a ceramic material used in a variety of memory applications,
microphones, transducers, actuators. They are also employed in MEMS devices.
PZT is Lead-Zirconate-Titanate or Pbx(Ti, Zr)1-xO3. A typical commercial composition has
~47 Mole-% PbTiO3 and ~53 Mole-% PbZrO3
PZT has a perovskite structure with an ABO3– structure type.
PZT exhibits good ferroelectric properties and excellent piezoelectric properties.
PEROVSKITE STRUCTURE
Virtually all piezoelectric materials crystallize in the perovskite structure .A representation of
eight perovskite unit cells on which most commercially available piezoceramics are based on.
The generic formula is ABO3– Oxygen sits in the octahedral sites (red small dots), an A++
material (e.g. Pb) in the cube corners (green big dots) and a small B++++ cation (e.g. Zr, Ti) in the
center (small black dots). The unit cell is electrically neutral.
4
EFFECT OF CURIE TEMPERATURE ON PIEZO ELECTRIC CERAMIC CRYSTAL
STRUCTURE :
A traditional piezoelectric ceramic is a mass of perovskite crystals, each
consisting of a small, tetravalent metal ion usually titanium or zirconium, in a lattice of larger,
divalent metal ions, usually lead or barium, and O2- ions.
a) Temperature above Curie point :
Cubic lattice, symmetrical arrangement of positive and negative charges.
b) Temperature below Curie point:
Tetragonal (orthorhombic) lattice, crystal has dipole moment. A piezo electric crystal
must always be operated below curie temperature ,since it loses its piezo electric capabilities
totally beyond this temperature.
5
O 2+ oxygen
Ti, Zr, other smaller, tetra valent metal ion
Pb , Ba, other larger divalent metal ion
WHY PARTICULARLY PZT IS SELECTED FOR OUR CIRCUIT? :
Among all piezoelectric materials, lead zirconate titanate (PZT) has been most extensively used
in transducers. This family of ceramics has high values for the piezoelectric charge coefficient
(d33), electromechanical coupling coefficient (kt) and dielectric constant (K). They also have low
electrical losses. Piezopolymers like Polyvinylidene Fluoride copolymers (PVDF) are an
alternative to piezoceramics. Their limitations for use as transducers include a low dielectric
constant (K) and coupling coefficient (kt), high electrical losses.
PRODUCTION OF PZT
To prepare a piezoelectric ceramic, fine powders of the component metal oxides are mixed in
specific proportions, and then heated to form a uniform powder. The powder is mixed with an
organic binder and is formed into structural elements having the desired shape (discs, rods,
plates, etc.). The elements are fired according to a specific time and temperature program, during
which the powder particles sinter and the material attains a dense crystalline structure. The
elements are cooled, then shaped or trimmed to specifications, and electrodes are applied to the
appropriate surfaces.
WORKING OF PZT
6
Small tetra valent ion is shifted from centre ,so that crystal loses its symmetry.
The displacement of electron densities occurs when the electrical voltage potential is
applied across the opposite crystal faces that could be used as an "electrical current" The reason
this "electrical current" is possible rests in the net movement of negative anion charges (-) in one
direction within the crystal, which is reinforced by the net movement of positive cation charges
(+) in the opposite direction. So, with the application of a "voltage potential", the electric field
compresses the crystal and a "electric potential" is created in one direction. If you now reverse
this voltage potential by releasing the compression, the ions or atoms will move in the opposite
direction which in turn causes the crystal to expand back to its natural form (Ellis et al).
ALTERNATIVE PIEZO ELECTRIC MATERIAL: PVDF, or PolyVinylidine DiFluoride,
is a highly non-reactive and pure thermoplastic fluoropolymer. It is also known as KYNAR.
PVDF is very expensive; its use generally reserved for applications requiring the highest purity,
strength, and resistance to solvents, acids, bases and heat. When poled, PVDF is a ferroelectric
polymer, exhibiting piezoelectric and pyroelectric properties. These characteristics make it useful
in sensor and battery applications. To give the material its piezoelectric properties, it is
mechanically stretched to orient the molecular chains and then poled under tension.
STUDY OF ELECTROMECHANICAL PROPERTIES
CONSTITUTIVE EQUATIONS
“d” FACTOR
ELECTRO MECHANICAL RELATIONS
7
CONSTITUTIVE EQUATIONS:
In order to describe or model piezoelectric materials, one must have knowledge about the
material's mechanical properties (compliance or stiffness), its electrical properties (permittivity),
and its piezoelectric coupling properties. Engineers are already familiar with the most common
mechanical constitutive equation that applies for everyday metals and plastics. This equation is
known as Hook’s Law and is written as:
S = s. T
In words, this equation states: Strain = Compliance × Stress.
Compliance can mean the inverse of stiffness.
Since piezoelectric materials are concerned with electrical properties too, we must also consider
the constitutive equation for common dielectrics:
D= ε.E
where D is volumetric charge density, is permittivity and E is electric field
strength.Permittivity is an intensive physical quantity that describes how an electric field affects
and is affected by a medium.
For piezo electric materials, The above two equations may be combined into so-called coupled
equations, of which the strain-charge form is:
{S}=[SE] {T} + [dt] {E}
{D}=[d]{T}+[ εT ] {E}
Where the superscript E indicates a zero, or constant, electric field; the superscript T indicates a
zero, or constant, stress field; and the subscript t stands for transposition of a matrix.
Also,
T = constant stress = mechanically free
E = constant field = short circuit
D = constant electrical displacement = open circuit
S = constant strain = mechanically clamped
The piezoelectric coupling terms are in the matrix d.
8
"d" CONSTANT:
The piezoelectric constants relating the mechanical strain produced by an applied electric field
are termed the strain constants, or the "d" coefficients. The units may then be expressed as
meters per meter, per volts per meter (meters per volt).
d33 - describes the strain parallel to the polarization vector of the ceramics (thickness) and is
used when calculating the displacement of stack actuators; d31 is the strain orthogonal to the
polarization vector (width) and is used for calculating tube and strip actuators .
ELECTRO MECHANICAL RELATIONS:
The relationships between an applied voltage or electric field and the corresponding increase or
decrease in a ceramic element's thickness, length, or width are:
h = d33V
l / l = d31E
w / w =d31E
where l: initial length of ceramic element
w: initial width of ceramic element
h: change in height (thickness) of ceramic element
l: change in length of ceramic element
w: change in width of ceramic element
d: piezoelectric charge constant
E: electric field
d33: piezoelectric charge constant, For a PZT ceramic is d33~ 400*10-12 m/V (Here i=j=3
which simply means that the strain and the voltage gradient are in the same direction.
PROPERTY ENHANCING METHODOLOGIES:
DOPING OF PZT TO FACILITATE DOMAIN WALL MOTION
PIEZO COMPOSITES
9
DOPING OF PZT TO FACILITATE DOMAIN WALL MOTION:
The material features an extremely large dielectric constant at the morph tropic phase boundary
(MPB) near x = 0.52. These properties make PZT-based compounds one of the most prominent
and useful electro ceramics. Commercially, it is usually not used in its pure form, rather it is
doped with either acceptor dopants, which create oxygen (anion) vacancies, or donor dopants,
which create metal (cation) vacancies and facilitate domain wall motion in the material. In
general, acceptor doping creates hard PZT while donor doping creates soft PZT.
PIEZO COMPOSITES: Instead of looking for an entirely new class of piezoelectric materials
without the existing limitations, researchers in the last two decades have successfully made
composites of piezoelectric ceramics with inactive polymers. These piezo composites show
excellent electromechanical properties while limiting the various detrimental properties of the
monoliths. The properties of the ceramic/polymer composites can be tailored by changing the
connectivity of the phases, volume fraction of the ceramic in the composite, and the spatial
distribution of the active ceramic phase.
PIEZO STACKS:
Description: A low voltage piezoelectric stack is a monolithic ceramic construction of many
thin piezo ceramic layers which are connected in parallel electrically. The common feature of
stack actuators is that many thin layers of piezoelectric material, typically PZT, are glued or
coifed together with an electrode between each layer. This arrangement allows the mechanical
displacement to sum in series while the electrical properties remain in parallel. This leads to
large displacements, 0.1% strain, for lower voltage levels than would be achievable with a
monolithic element of same length. Stacks can be built with aspect ratios up to 12:1
(length:diameter). This means that the maximum travel range of an actuator with 15 mm piezo
diameter is limited to about 200 µm. Longer travel ranges can be achieved by mechanical
amplification techniques.
STACK ACTUATORS:
10
The principal characteristics of the stack are:
1. high energy conversion efficiency,
2. low voltage operation, large force,
3. Low motion, fast response.
Motion may be increased, at the expense of force, by mechanical amplification. The stack offers
a high energy density in a small package. Due to its superior compressive strength, it provides a
high load bearing capability. However, it is relatively weak in tension. Generally, excitation
should be applied only in the direction of polarization. The common feature of stack actuators is
that many thin layers of piezoelectric material, typically PZT, are glued or coifed together with
an electrode between each layer. This arrangement allows the mechanical displacement to sum in
series while the electrical properties remain in parallel. This leads to large displacements, 0.1%
strain, for lower voltage levels than would be achievable with a monolithic element of same
length.
ACHIEVING MAXIMUM EFFICIENCY OF THE INVERSE PIEZOELECTRIC
EFFECT
RESONANCE FREQUENCY
RESONANCE FREQUENCY:
A piezoelectric ceramic element exposed to an alternating electric field changes
dimensions cyclically, at the frequency of the field. The frequency at which the element vibrates
11
most readily in response to the electrical input, and most efficiently converts the electrical energy
input into mechanical energy -- the resonance frequency -- is determined by the composition of
the ceramic material and by the shape and volume of the element.
STUDY OF LIMITATIONS OF PIEZOCERAMICS
STABILITY
ELECTRICAL LIMITATIONS
THERMAL LIMITATIONS
MECHANICAL LIMITATIONS
STABILITY: Most properties of a piezoelectric ceramic element erode gradually, in a
logarithmic relationship with time after polarization. Exact rates of aging depend on the
composition of the ceramic element and the manufacturing process used to prepare it.
Mishandling the element by exceeding its electrical, mechanical, or thermal limitations can
accelerate this inherent process.
ELECTRICAL LIMITATIONS :
Exposure to a strong electric field, of polarity opposite that of the polarizing field, will
depolarize a piezoelectric material. The degree of depolarization depends on the grade of
material, the exposure time, the temperature, and other factors, but fields of 200-500 V / mm or
greater typically have a significant depolarizing effect. An alternating current will have a
depolarizing effect during each half cycle in which polarity is opposite that of the polarizing
field.
MECHANICAL LIMITATIONS:
Mechanical stress sufficient to disturb the orientation of the domains in a piezoelectric material
can destroy the alignment of the dipoles. Like susceptibility to electrical depolarization, the
ability to withstand mechanical stress differs among the various grades and brands of
piezoelectric materials.The bending forces generated by converse piezoelectricity are extremely
high and usually cannot be constrained. The only reason the force is usually not noticed is
because it causes a displacement of the order of one millionth of an inch (a few nanometers).
12
THERMAL LIMITATIONS:
If a piezoelectric ceramic material is heated to its Curie point, the domains will
become disordered and the material will be depolarized. The recommended upper operating
temperature for a ceramic usually is approximately half-way between 0°C and the Curie point.
Within the recommended operating temperature range, temperature-associated changes in the
orientation of the domains are reversible. On the other hand, these changes can create charge
displacements and electric fields. Also, sudden temperature fluctuations can generate relatively
high voltages, capable of depolarizing the ceramic element. A capacitor can be incorporated
into the system to accept the superfluous electrical energy. The system dissipative power is
eventually transformed into internal heat energy in PZT element. An increase in the
temperature of the actuators is thus inevitable. The phenomenon of temperature rise of PZT
actuators has often been observed in experiments. When PZT elements operate at a certain
temperature, piezoelectric properties, such as dielectric constant and the piezoelectric constant,
change because of the strong temperature dependency. In practice, as PZT elements are used
for structural actuation at the system resonance or with a large electrical field, heat generation
throughout PZT actuators may be significant. Therefore, the heat transfer analysis of integrated
PZT elements in large electric field applications are is important.
THE STATE-OF-THE-ART RESEARCH ON PZT:
In the application of PZT materials indicates that numerous issues remain unanswered
about the application of piezoelectric and their limitations. Research on modeling is needed to
predict the behavior. On the materials engineering side investigation for enhancing mechanical
properties of piezoelectric is needed. However, much less research has been performed on
structures with curvatures and further research in this area is needed.
PIEZO CERAMICS IN MEMS
Current electronic devices which are based on piezoelectric properties, according to Ballato
(1996), have expanded in their application beyond that of crystal oscillators. Such piezoelectric
devices are being used as transducers in telephone speakers and sonar arrays as well as
mechanical actuation and sensing microstructures on electronic micro-chips. These MEMS
devices can provide signal sensing, processing, and output functions that were unattainable by
electronic or photonic methods alone.
13
Another compelling aspect of piezoelectric application, suggests, is that of micro- and nano-
electronics which are constructed on the behavior of charged species when they are subjected to
an electric field. The extreme miniaturization of these structures is based on their ability to take
on a "capacitor-like" form, thereby removing the need for bulky inductors and replacing them
with "thin, planar electrodes" which now introduce electric fields for circuit operations. These
"introduced electric fields" can also provide forces needed to drive mechanical motions in a
piezoelectric device by making use of the voltages resident on the micro-chips by way of the
piezo effect. The phenomenon of piezoelectricity is also evident in ultra sensitive micro-
positioning.
CLASSIC VIBRATION ALERTS IN MOBILE PHONES:
A Micro motor is used in the mobile phones for vibration alerts. It has an eccentric weight
mounted on the drive shaft which attains resonance when rotated at some frequency thus
produces vibrations. Its common that mobile phone in vibration mode will run out of battery
soon. But the strain produced in the piezo ceramics is very large with very minimal voltage
consumption .They also have low electrical losses because of its material properties. So this
application will give effective reduction in battery power consumption.
BASIC CIRCUIT DESIGN FOR APPLICATION OF USING P Z T IN MOBILE PHONE
VIBRATION:
14
THE FUNCTIONS OF THE CIRCUIT:
1. Signals are received by the antenna.
2. Band pass filter and RF amplifier will filter out the desired band width from signals.
3. Mixer combines the sine wave from local oscillator to the filtered signals thus
producing an output having frequency as difference between the signal frequency and
oscillator frequency.(i.e. intermediate frequency)
4. I F amplifier provide most of the receiver’s gain and selectivity.
(Selectivity is ability to separate signals from interference and noise)
5. Modes of switch operation :
No call or message: S1 and S2 open.
Call alert : S1 close and S2 open
Call attended/rejected:S1 open
Call attended: S2 close.
Call rejected: S1 open.
6. When switch S1 is closed, electric field is provided to PZT in polarization direction
and it vibrates.
7. When messages are received only preset number of pulses is sent to PZT so it
vibrates a few number times and automatically stops on the end of pulses.
PZT
Antennae
RF amp
Band pass filter
Mixer
IF amp
Detector
Local oscillator
Audio amp
Metal substrate
Band pass filter
S 1
S 2
LS
Mob
il
e
15
8. Since PZT has high resonance frequency the vibration are passed through metal
substrate to produce good sense of vibration.
ADVANTAGES:
Classic micro motor is replaced by PZT ceramic, hence less moving parts.
very reliable
current consumption is nearly 8 to 10 mA (in motor its 120-160mA)
low power requirements (if used ideally)
fast-acting and highly controllable
EPILOGUE:
Significant progress has been made in recent years in the field of smart materials and
structures. However, further research is needed before these materials can be utilized as viable
options for engineering applications. The most promising areas in the field of smart material and
structures include integration and miniaturization, active control and self-adaptation, and
diagnostic and self-repairing. Our design is still in its nascent stage lot of enhancements are
feasible .To conclude, smart materials will lead a major role in building up intelligent home and
unmanned factory, which are the vision of today’s engineering ad technology.
Acknowledgements:
We sincerely thank the following dignified staffs of our college for their kind help and guidance
to finish this paper successfully.
[1].Th.G.Sakthinathan, Lecturer, Dept. of Manufacturing Engg ,CEG, Anna Varsity.
[2]. Dr. P. Vanaja Rajan ,Assistant Professor, Dept. of EEE, CEG, Anna Varsity.
[3]. Th.Pughazalendi Sukumaran , Lecturer, Dept. of EEE, CEG, Anna varsity.
References:
[1]. Smart talk given by Dr. Siva Kumar, Dept of Physics, Anna varsity
16
[2]. Technical papers from 1996 ASME International Mechanical Engineering Congress and
Exhibition in Atlanta.
[3].www.efunda.com ,www.intellimat.com
[5] .Web site of APC international limited.
[6].Piezoelectric effect and its applications, by Sherri Garcia Edward (1998)
[7].Crystalline Dielectrics, volume 2, By I.S, Zheludev, Institute of crystallography, Moscow.
17
top related