acurlite structural skylights, inc. for commercial daylighting - all … · 2020. 6. 3. · use...

ISOMETRIC VIEW

DOUBLE PITCHW/ GABLE END C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

STANDARDSYSTEMDETAILS

11/30/17 - A

SAMPLE

N.T.S.

INSULATED CLOSURE - FOR ADDITIONAL COST(Factory Assembly Includes Rigid Insulation & Formed Backer)

ALUM. GLASS REST & SILICONE SETTING BLOCK(Located At Quarter Points - 2 Per Bay)

SILICONE GASKET

BACKER ROD & CONTINUOUS SEAL

EXTRUDED ALUMINUM PURLIN(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

FASTEN PURLIN ASSEMBLY TO RAFTER

EXTRUDED ALUMINUM RAFTER(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

TYPICAL DETAIL

CURB MUST RESIST ALL LOADS/REACTIONSIMPOSED BY SKYLIGHT

(Reactions Provided By Acurlite P.E.)(Responsible E.O.R. to Verify and Approve)

SILL LUG(Lug Size, Type & Locations Per Acurlite P.E. Analysis)

30.26°712

INSTALLATION

FASTEN PRESSURE CAP TO RAFTER & APPLY SEAL

EXTRUDED ALUM. COVER CAP & PRESSURE CAP W/ GASKET

INSTALL GLAZING PER INDUSTRY STANDARDS(Follow GANA Guidelines & Acurlite Installation Manual)

INSULATED LAMINATED / LAMINATED GLAZINGINCLUDES ALL BACKER ROD & GLAZING SEALANTS

(Max Unit Size & Required Thickness - Per AAMA Guidelines)(Glazing Calculations Provided For Additional Cost)

ISOLATION/WATERPROOF MEMBRANE(Not By Acurlite - Provided By Others)

FASTEN RAFTER ASSEMBLY TO LUGS - IF REQ.

FULL BEARING SHIM - IF REQUIRED(1/4" Max. Shim Space Typical - Unless Noted Otherwise)(Not by Acurlite - Provided By Others)

MINERAL WOOL TO FILL VOIDS - FOR ADDITIONAL COST(Standard Batt Type - Installer To Ensure System Weep Path Is NOT Blocked)

FASTEN SILL LUG TO CURB(Seal In & Around Lug & Fastener)

INSTALL SILL PAN IN BED OF SEALANT

SPONGE GASKET - FACTORY APPLIED TO SILL PAN(3/4" Void At System Weep As Required)

FORMED EXTERIOR CLOSURE - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)

(Typical Splice Shown As Dashed Line - Locate As Required)

DETAILS AS SHOWN ARE TYPICAL & FOR REFERENCE(Consult Factory for Additional Modification & Performance Improvements)

CURB SHOULD BE PLUMB, LEVEL & SQUAREPER INDUSTRY STANDARD TOLERANCES

(Max Allowed ±1/8" PER 12' - 0" - Unless Noted Otherwise)(Not By Acurlite - Provided By Others)

PLEASE NOTE

ALL ROOFING, TERMINATION BARS, REGLETS,COUNTER FLASHINGS & FLASHINGS NOT

INTEGRAL TO SKYLIGHT SYSTEM FUNCTION(Not By Acurlite - Provided By Others)

STRUCTURAL SEAL FLANGE - IF REQUIRED(Factory Applied To Purlin - 1/4-20 x 3/4" Flat Head Screw)

DETAILS / MATERIALS PER CONTRACT DOCUMENTS(Not By Acurlite - Provided By Others)

FORMED SILL PAN - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)

APPLY CONT. STRUCTURAL SEAL - IF REQUIRED

PROPER SUBSTRATE REQUIRED FOR ATTACHMENT(Not By Acurlite - Provided By Others)

FASTEN EXTERIOR CLOSURE TO SILL PAN(Use #10 x 1/2" Pan Head S.M.S. - Locate 12" O.C. Typical)

FASTEN EXTERIOR CLOSURE TO PURLIN / FLANGE

USE SPECIFIED DOW CORNING SILICONE(Per Acurlite P.E. Analysis & Installation Manual)

FASTENERS PROVIDED BY ACURLITE(Fastener Size & Type Per Acurlite P.E. Analysis Unless Noted)

OPTIONS FOR THERMAL ENHANCEMENT

SNAP ON COVER CAP(Not Required For Water Tightness)

CURB / SUBSTRUCTURE BY OTHERS

STANDARD & CUSTOM FINISHES(Paint, Anodize & Powder Coat Available)

SHADES/LOUVERS - PANELS - BIPV/DYNAMIC GLAZING(Consult Factory For Your Project Specific Requirements)

OPTIONS FOR VISUAL ENHANCEMENT

VARIABLE SLOPE - ALL PITCHES AVAILABLE(Consult Factory - Based On Project Specific Conditions)

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

USE SPECIFIED DOW CORNING SILICONE(Per Acurlite P.E. Analysis & Installation Manual)30.26°7

INSTALLATION

(Max Unit Size & Required Thickness - Per AAMA Guidelines)(Glazing Calculations Can Be Provided For Additional Cost)

EXTRUDED ALUM. PURLIN(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

SILICONE GASKET

EXTRUDED ALUM. RAFTER(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

STRUCTURAL SEAL FLANGE FASTENED TO PURLIN(Factory Applied To Purlin - 1/4-20 x 3/4" Flat Head Screw)

PURLINTYPICAL DETAIL

D2 C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

TYPICAL DETAILRIDGE

FASTEN PURLIN ASSEMBLIES TO RAFTER

FASTEN RAFTER ASSEMBLIES TOGETHER - IF REQ.(Gusset Factory Applied to (1) Rafter Assembly Of Each Pair)

INSTALLATION

30.26°712

INSULATED CLOSURE - FOR ADDITIONAL COST(Factory Assembly Includes Rigid Insulation & Formed Backer)

FORMED EXTERIOR CLOSURE - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)(Typical Splice Shown As Dashed Line - Locate As Required)

SILICONE GASKET

EXTRUDED ALUMINUM PURLIN(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

EXTRUDED ALUMINUM RAFTER(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

EXTRUDED ALUM. COVER CAP & PRESSURE CAP W/ GASKET

STRUCTURAL SEAL FLANGE - IF REQUIRED(Factory Applied To Purlin - 1/4-20 x 3/4" Flat Head Screw)

INSULATED LAMINATED / LAMINATED GLAZINGINCLUDES ALL BACKER ROD & GLAZING SEALANTS(Max Unit Size & Required Thickness - Per AAMA Guidelines)(Glazing Calculations Provided For Additional Cost)

ALUMINUM GUSSET PLATES(Size, Thickness & Type Per Acurlite P.E. Analysis)

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

TYPICAL DETAILJAMB

PLEASE NOTE

SILICONE GASKETEXTRUDED ALUM. PURLIN(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

INSULATED LAMINATED / LAMINATED GLAZINGINCLUDES ALL BACKER ROD & GLAZING SEALANTS(Max Unit Size & Required Thickness - Per AAMA Guidelines)(Glazing Calculations Can Be Provided For Additional Cost)

SHADES/LOUVERS - PANELS - BIPV/DYNAMIC GLAZING(Consult Factory for your project specific needs)

EXTRUDED ALUM. COVER CAP& PRESSURE CAP W/ GASKET

COUNTER FLASHING & REGLETS(Not By Acurlite - Provided By Others)

FASTEN EXTERIOR CLOSURE TO CURB(Shim & Seal As Required)

INSTALLATION

LAP MEMBRANE INTO SYSTEM(Not By Acurlite - Provided By Others)

FASTEN EXTERIOR CLOSURE TO ANGLE SPACER(Not By Acurlite - Provided By Others)

FORMED ANGLE SPACER - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)(Factory Applied To Rafter)

FASTEN PURLIN ASSEMBLY TO RAFTERBACKER ROD & CONTINUOUS SEAL

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

SILICONE GASKET

INSTALLATIONOPTIONS FOR VISUAL ENHANCEMENT

SNAP ON COVER CAP(Not Required for Water tightness)

ALUM. GUSSET PLATES(Size & Type Per Acurlite P.E. Analysis)

FASTEN RAFTER ASSEMBLIES TOGETHER - IF REQ.(Gusset Factory Applied to (1) Rafter Assembly Of Each Pair)

RAFTERTYPICAL DETAIL

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

GABLE HEADD6

TYPICAL DETAIL

SILICONE GASKETEXTRUDED ALUM. PURLIN

(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

INSULATED CLOSURE - FOR ADDITIONAL COST(Factory Assembly Includes Rigid Insulation & Formed Alum. Backer)

FASTEN HEAD LUG TO RAFTER(Seal In & Around Lug & Fastener)

FORMED EXTERIOR CLOSURE - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)

(Typical Splice Shown As Dashed Line - Locate As Required)

INSTALLATION

GABLE HEAD LUG(Lug Size, Type & Locations Per Acurlite P.E. Analysis)

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

TYPICAL DETAILGABLE SILL

PLEASE NOTE

SPONGE GASKET - FACTORY APPLIED TO SILL PAN(3/4" Void At System Weep As Required)

INSULATED LAMINATED / LAMINATED GLAZINGINCLUDES ALL BACKER ROD & GLAZING SEALANTS(Max Unit Size & Required Thickness - Per AAMA Guidelines)(Glazing Calculations Can Be Provided For Additional Cost)

SILICONE GASKET

FORMED ANGLE SPACER - 1/16" ALUM. STANDARD(Consult Factory For Optional Thickness & Materials)(Factory Applied To Purlin)

FULL BEARING SHIM - IF REQUIRED(1/4" Max. Shim Space Typical - Unless Noted Otherwise)

(Not by Acurlite - Provided By Others)

INSTALLATION

FASTEN EXTERIOR CLOSURE TO SILL PAN(Use #10 x 1/2" Pan Head S.M.S. - Locate 12" O.C. Typical)

FASTEN EXTERIOR CLOSURE TO ANGLE SPACER(Use Pop Rivets As Required)

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

TYPICAL DETAILGABLE POST

SILICONE GASKETEXTRUDED ALUM. PURLIN

(2 1/2" Width - Depth/Reinforcement Per Acurlite P.E. Analysis)

INSTALLATION

FULL BEARING SHIM - IF REQUIRED(1/4" Max. Shim Space Typical - Unless Noted Otherwise)(Not by Acurlite - Provided By Others)

SILL CURB - INSIDE EDGE(Not Provided By Acurlite - Provided By Others)

C.H.M.

DRAWN BY:

K.A.M.CHECKED BY:

DATE - ISSUE:

SHEET:

SCALE:

11/30/17 - A

6" = 1' - 0"

acurlite structural skylights, inc. for commercial daylighting - all … · 2020. 6. 3. · use...

Documents

daylighting design

140430 daylighting

why skylights? skylights pamphlet.pdf · functionality of a...

residential skylights & sun tunnel...

aerogel skylights

energy efficient skylights

skylights: calculating illumination levels and energy ......

validated interactive daylighting analysis for ... ·...

fused glass skylights

daylighting in...

anidolic daylighting system: a sustainable daylighting...

daylighting slideshare

sustainability inspires polycarbonate skylights for...

pmd - belle skylights

tprs limited lifetime warranty - owens corning · owens...

daylighting - etsav.upc.edu

skylights + walls + canopies

by: ken sheeks, owner/gm hawaii skylights and solar...

velux skylights

velux modular skylights -...