advanced rfic design elen359, lecture 3: gilbert cell mixersconverting mixer for wi-fi copy right...

Advanced RFIC Design ELEN359A, Lecture 3: Gilbert

Cell MixersInstructor: Dr. Allen A Sweet

Copy Right 2004

All of Design is the Art and Science of Navigating Tradeoffs

• Science gives us the tools to understand what nature, in the form of the laws of physics, will allow us to do and not to do.

• Tradeoffs are the points where we as designers must make decisions.

• The Art of design is the process by which we make good decisions given numerous factors such as economics, market acceptance, cost of development, competitive pressures, etc.

Copy Right 2004

Basic Non Linear Process Produces Mixer Action

• Active Device Non Linearity is Expressed as a Power Series relating the device’s Voltage and Current: I(t) = I0 + k1V + k2V*2 + k3V*3 + …

• If V = V1 + V2 (two input signals), the second order term becomes: k2(V1*2 + V1V2 + V2*2). It is the V1V2 product term that produces mixing action because if V1 and V2 are sin waves, their produce, (v1cosW1t)x(v2cosW2t) = (v1v2/2)[cos(W1-W2)t + cos(W1+W2)t] contain the sum and difference mixing Frequencies.

Copy Right 2004

Down Converting Mixer: Applications to Receivers

FI=Fl-Fr

Copy Right 2004

Up Converting Mixer: Applications To Transmitters

FR=Fl+/-FIUSBLSB

Copy Right 2004

Double Balanced Diode Mixer Topology

L VirtualGround

R VirtualGround

Copy Right 2004

Diode IV Characteristics

Copy Right 2004

VBIC Diode IV

Copy Right 2004

ADS Schematic of a Balanced 4 Diode Mixer

Copy Right 2004

HB Controller, Gain Equation and RF Source

Copy Right 2004

LO Source

Copy Right 2004

HB Controller

Copy Right 2004

HB Controller to Sweep RF_pwr

Copy Right 2004

Conversion Loss vs RF_pwr

Gain CompressionBegins

Copy Right 2004

HB Controller to Sweep LO_pwr

Copy Right 2004

HB Controller to Sweep LO_pwr

Copy Right 2004

Conversion Loss vs LO_pwr

(LO Amp Requires100 mA Current @30 % efficiency)

(Preamp Requires20 mA Current to Boost Gain to +10 dB)

Copy Right 2004

Single Balance Bipolar Transistor Multiplying Mixer Topology

Vi = Vl x Vr

Q1 collector currentControls Transconductance

Copy Right 2004

Advantages of a Single Balanced Bipolar Transistor Multiplier

• High Conversion Gain (5 to 10 dB)• High L to R Isolation (but not high L to I

Isolation).• Low LO power Requirement (-10 to 0

dBm).• IIP3 is higher than the LO power level. • Low DC Power, Small size

Copy Right 2004

Double Balanced (Gilbert Cell) Bipolar Transistor Mixer

Copy Right 2004

Advantages of a Gilbert Cell Transistor Mixer

• All Three ports are differential, which is a natural configuration for creating Quadrature Phase Modulators and Detectors.

• L to R, L to I Isolations are excellent. • All the Advantages of the Single Balanced

Transistor Mixer are available in this case.

Copy Right 2004

A Direct Conversion Receiver using Gilbert Cell Mixers

Copy Right 2004

Gilbert Cell Mixer Topology

Copy Right 2004

Fully Differential Mixer Cell

Copy Right 2004

Series Diode Bias Tree

Copy Right 2004

DC Power and Output Term

Copy Right 2004

RF and LO Sources

Copy Right 2004

HB Controller and Equations

Copy Right 2004

Harmonic Balance Controller

Copy Right 2004

DC Analysis

Copy Right 2004

Bias Tree DC Levels

Copy Right 2004

MIX Function Determines Frequency Index

Copy Right 2004

Basic Simulation Calculates Conversion Gain in Two Ways

Copy Right 2004

LPF Eliminates Spurious Signals in the Mixer’s Output

Copy Right 2004

Mixer Simulation including an Output LPF.

Copy Right 2004

HB Controller to Sweep LO_pwr

Copy Right 2004

HB Controller to Sweep LO_pwr

Copy Right 2004

Simulation of Gain vs LO_pwr

Copy Right 2004

HB Controller for Sweeping RF_pwr

Copy Right 2004

HB Controller to Sweep RF_pwr

Copy Right 2004

Simulated Gain vs RF_pwr

(P-1dB)

Copy Right 2004

S Parameter Controller Simulates Isolations and Matches

Copy Right 2004

Matches and Isolations of a Gilbert Cell Mixer

Copy Right 2004

Disabling one Transistor Creates Imbalance and Poor Isolation

Copy Right 2004

Gilbert Cell Up Converter

(i.e. F2+/-F1)

Copy Right 2004

Up Converting Mixer HB Controller and Equations

Copy Right 2004

Sources for Up Converting Mixer

Copy Right 2004

BPF Selects a USB or an LSB Output

Copy Right 2004

Up Converter Simulation Including MIX Function Table

Copy Right 2004

USB Output is Selected with the BPF

Copy Right 2004

HB Controller and Equations to Simulate OIP3

Copy Right 2004

LO and RF Sources for Intermodulation Simulations

Copy Right 2004

HB Controller-Freq

Copy Right 2004

HB Controller-Sweep

Copy Right 2004

HB Controller- Solver

Copy Right 2004

HB Controller- Params

Copy Right 2004

MIX Function Determines Frequency Index for each Signal

Copy Right 2004

Intermodulation Spectrum

Copy Right 2004

Gain and OIP3(upper and lower) vs LO_pwr

(dBm)

(dB)

Copy Right 2004

LO and RF Sources to Simulate Non Linear Noise Figure

Copy Right 2004

HB Controller and Equations for Noise Figure Simulation

Copy Right 2004

HB Controller-Freq

Copy Right 2004

HB Controller-Params

Copy Right 2004

HB Controller- Noise(1)

Copy Right 2004

HB Controller-Noise (2)

Copy Right 2004

HB Controller-Solver

Copy Right 2004

HB Controller- Output

Copy Right 2004

Simulated ssb Noise Figure

Copy Right 2004

Simulated Noise Figure (dsb) and Conv Gain

Copy Right 2004

Noise Voltage Output at 400 MHz in a 1 Hz Bandwidth

Copy Right 2004

Home Work #2:A Down Converting Mixer for Wi-Fi

Copy Right 2004

• Design a Down Converting Gilbert Cell Mixer for 802.11B (RF_freq=2400 MHz). This mixer will down convert received Wi-Fi signals to an IF frequency of 850 MHz where a cellular/PCS receiver will process them. Conversion gain is to be at least 10 dB. As part of the design, an integral HPF (designed per lecture 2) in front of the mixer will reduce PCS interference at 1800 MHz by at least 20 dB.

• LO_pwr=-10 dBm, Vcc=+5.0 volts, Ic=10 mA max. All transformers are off chip.

Home Work #3: Advanced Wi-Fi Mixer

• Simulate the three isolations, the three matches, P-1dB compressed power, upper and lower OIP3, and the large signal noise figure for the mixer you designed in home work #2.

• Layout your Wi-Fi mixer using Knowledge On design rules. All three radio frequency ports (RF, LO, and IF) are to be pairs of standard bonding pads, spaced by 150 microns (c-c) which can be bonded to three off chip transformers. A 7th pad is Vcc. Keep your layout as “square” as possible.

Copy Right 2004