akg c422, c34, c33 stereophonic condenser microphones
Post on 23-Jan-2017
234 Views
Preview:
TRANSCRIPT
DESCRIPTION middot C422 (Large Diaphragm) The C422 is a studio condenser microphone that has been specially designed for sound
studio and radio broadcasting The microphone head holds two twin diaphragm condenser capsules elasticly suspended to protect against handling noise
The rugged wire mesh cap protects the capsules from mechanical damage It is differently colored at the two opposing grille sides (bright = front grille side dark = rear grille side) thereby allowing relative pOSi tion of the two systems to be easily checked The microphone head as a whole may be rotated by 45 deg about the shaft in counter middotc lockwise direction pOSition 0deg and 45deg being lockable This will allow quick and exact change-over from 0deg (for MSshystereophony) to 45deg (for XV-stereophony) even when the microphone is rigidly mounted The upper system may be rotated by 180 deg against the lower one A scale on the houSing adjustshyment ring and arrow-shaped mark on the upper system will allow the base angle to be exactly adjusted Any desired readjustment may be easily effected by means of the exact angle markshying The C422 is characterized by another special feature since in sound studio work and radio broadcasts it is often necessary to recognize the respective positions of the two systems even from a greater distance two light emilling diodes with particularly narrow light emitting angle have been incorporated both in the upper rotatable and in the lower system
The LEOmiddots are energized by a conventional 9V battery (IEC 6F22) or 9V accumulator cell which is continuously charged during operation via phantom power supply
The LED s are switched onloff by means of a separate switch in the S42E Enclosed within the microphone shaft there are separate FET-preamplifiers for each channel which are characterized by particularly high input impedance extremely low internal noise and high crosstalk attenuation The output level of both channels may be simultaneously lowered by 10 or 20 dB
The C422 is connected to a S42E remote control unit which allows anyone of 9 polar patterns to be selected for each channel Due to noiseless selection polar pattern changeover will be possible even during recording
DESCRIPTION middot C34 (Small Diaphragm) The C34 is a stereo condenser microphone that has been specially deSigned for sound
studio radio broadcast and mobile use The microphone head holds 4 condenser capsules elastically suspended to protect them from handling noise
The rugged wire mesh cap protects the capsules from mechanical damage The upper system may be rotated by 180deg whereas the lower one is rigidly connected with the microphone shafl This will allow different base angles to be easily adjusted for stereo transmissions The wire mesh cap is differently colored at the two opposing grille sides (bright = front grille s ide dark = rear grille side) thereby allowing the relative pOSition of the two systems to be easily checked An additional scale on the rigid housing ring and an arrowshyshaped mark on the rotatable housing ring will allow the base angle to be exactly adjusted and readily readjusted if deSired Enclosed within the microphone shaft there are separate FETshypreamplifiers for each channel which are characterized by particularly high input impedance extremely low internal noise and high crosstalk attenuation The satin-black fini sh of the microphone will assist in preventing disturbing light reflections in film and TV-studio work
The C34 is connected to a S42E remote control unit which allows anyone of 9 polar patterns to be selected for each channel Due to noiseless selection polar pattern changeover will be possible even during recording
DESCRIPTION middot C33 (Small Diaphragm) The C33 is a stereo condenser microphone designed for use in concert halls recording and
broadcasting studios for film video and sound stages The C33 uses two fixed pattern (carshydioid) capsules This straight forward design offers unsurpassed sound while providing an economical convenient and foolproof approach to X-Y stereo recording techniques
The microphone contains two identical small-diaphragm capsules one fi xed to the main housing and the other continuously rotatable through an angle of 0deg to 180deg This arrangement allows for easy selection of the different base angles requ ired between the capsules for various X-Y stereo recording techniques Each capsule is followed by a FET preamplifier with high input impedance and excellent signal-to-noise ratio
The output of the C33 is a 5-pin XLR-type connector The necessary operating voltages for the C33 are supplied by any standard phantom-power from 9 to 52 volts and 5 mA per channel (DIN 45 596) To mount the C33 place it in the H 1516 shock mount (included) and lock it in place as shown The H 1516 may be mounted on any stand or boom with 38 518 or 12
threads by appropriate use of the thread adapter supplied in the H 1516
0008
0008
00
--
+10 t--- shyo dB
- 10
~V 1m ( rv 3 114 ) ON AXIS AND 180 OFF AXIS AT B (FIGURE - 8) SET TING OF PATTERN -SELECTOR
SWITCH
MINIMUM REJECTI ON AT 75 -105deg OFF AXIS +3dB DE VIATION ALLOWABLE
WITH IN ANY ONE OC TAVE
50 100 200 500 1000 2000 5000
FREQUENCY AND POLAR RESPONSE CURVES
C33 CARDIOID +20
+10
o dB
2OH
- middot( 1)middot 00- 1 bull bull
Im ( V3 - 14 ) ON A X I S -t--t-t- r--
MIN IMUM REJECTION AT laomiddot OFF AXI S + 3dB DE VIATI ON ALLOWABLE WI THIN ANY
ONE OC TAVE
-
50 100 200 500 1000 2000 5000 10 000 20000
90i-++t-+-H H-+-H--I-I90middot
-10
-20
2000 He 250Hc 4000 HI 500H z 8000 HI
1000 H I __ I6DOCH I
125 Hz
C34 OMNI +10
o dB
- 10
-20
20Hz
CARDIOID +20
+10
o dB
- 10
-20
20Hz
FIGURE 8 +20
+10
o dB
-10
-20
J J~_h ( ~ IOII - IQi-I1
- 1m ( 3 -11 4 ) ON AXI S AT 0 (OMNIDIR ECT IONAL) shySETTING OF PATTERN-SELECTOR SWITCH
90deg1-++-I+ H H-+-H +-I90middot
125 H 2000 Hz __ 250Hz -- 4000 Hz-t
500 Hz 8000 Hz 100 200 500 1000 2000 5000 10000 20000 1000 H l _ _ I SeOO HI
~ -~) bullbull It1l I-IOII~I 1
m ( V3 - 114)ON AXIS AT Q (CA RDI OID) fshy SETTI NG OF PATT ERN -SELE CTOR SWITCH
ANY ONE OC TAVE
12 5H z -- 2000Hz -- 250Hz --- 4000Hz
500 HI 8 000 Hz 100 200 500 1000 2000 5000 10 000 20000 1000 Hz _ _ 16DOCH I
-~ l iIII -IV_-Ili llm ( 3 -14) ON AXIS AND 18 0 0 OFF AXIS AT 8(FIGURE - 8) SE TTiN G OF PA TTE RN-SELE CTO R SWIT CH
90deg1-+-H~H H ---laquoH -H90
+- tshy~
12 5 H1
250 Hz -- ~ggg~~ 500 Hz 8000 Hz
100 200 500 1000 2000 5000 10000 20000 100 0 Hz __ 16eOCHz
C422 OMNI +10
o dB
- 10
-20
20Hz
CARDIOID +20
20Hz
FIGURE 8 + 20
-20
20 Hz
- 1m (-3-114) ON AX IS AT 0 (OMNIOIRECTIONAL SETTING OF PATTERN- SELE CTOR SWIT CH
50 100 200 500 1000 2000 5000
50
=shy+10
o dB
-10
-20
1- VIm ( V 3 -14 ) ON AXIS AT Gl (CARDIOID) U ~ bull uIC~ID~ co- IN
SETTING OF PATTERN-SELECTOR SWITCH f shy
bshy~~
MIN REJECT ION AT lBO OFF AXIS +3dB DEV ALLOWABLE WITHIN ANY ONE OCTAVE - ~--
- f-shy
100 200 500 1000 2000 5000 10000 20 000
20 Hz
50
50
50
-f shy
90middotf+ +-++H
125 H 2000 HI 25 0 Hz --
30middot
4000Hl -- 500HZ 8000 HI
10000 20000 1000 Hz _ _ 16aOOHl
90 0H 4-H+r H+I+ H90middot
ut~jA I 0
900H+fcll+r J-i~H-H90middot
12 5 Hz -- 2000 HI 250 HI 4000 HI 500 Hz eooo HI
10000 20000 1000 Hz - - ISe OCHI
- MINIMUM REJEC TION AT 180 OFF AXIS --=l shy+3dB DEVIATI ON ALLOWABLE WITHIN
MINIMUM REJE CTI ON AT 75middot- 105 OFF AXIS +3dB_ DEVIATION ALLOWABLE WITHIN ANY ONE OCTAVE
BLOCK DIAGRAMS C422C34
I
I
---
t
12V ----~-
I Kshy MK 42120
Mshy
0shy ch 1 f----i S 42 E
cshy ch2
Jshy
BshyI
) Ashy
C33 - _--- XLR-Sshy
--+----+-0 2
1 1
1 I Channel l Chunnel l -------+-03 I
I I I I I I I I I I
I I
i Ch anne l 2 Channel 2 1 I I I laquo11 plusmn
DIMENSION DIAGRAMS 1-58
C422
r---- 4-34--- -1
~------8-1316 ------ shy
1-1132
C34 --l -c=c[JJ]---~ml15i31
65 1~---4-114 I I 7-916
C33 11132 1-3116
knn~fGIII~L____==ll I I I1----4114-----1 I
I 7916
SPECIFICATIONSmiddotC33 SPECIFICATIONSmiddotC422 SPECIFICA TlONSmiddotC34
Mode of Operation 2 twin diaphragm systems pressure gradient receivers
Frequency Range 20-20kHz
Sensitivity at 1000Hz 6mVPa - 645dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~500 ohms
Equivalent Noise Level lt 22dB (filter CCITT-C DIN45405)
Weighted Noise Level Approx 16uV RMS (filter CCITT-C DIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 5uV5uT
Max Sound Pressure Level (for 1000Hz) and 500 ohms load Impedance harmonic distortion k = 05 ) 92Pa ~ 133 dB SPL
Admissible Climatic Conditions Temperature Range (- 20degC- 4 deg to 60degC148 deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via S42E with phantom power supply
Current Consumption 5mA max for misc (each ch ) Approx 50mA for LED s
Dimensions 3342 mm (129165 in) 0 x 235mm (9 25 in) in length
Connector Type 12 pica miniature DIN plug
Finish Satin-black chromium -plated all-metal housing
Weight Approx 430g (1518 oz)
Included Accessories W42 foam wind shyscreen H159 elastic suspension MK4220 cable (20m) S42E remote control unit individual frequency curves case
Recommended Accessories SA42 stand adapter H42 suspenshysion ring N62E power supply unit (2ch) N66E power supply unit (6ch)
Mode of Operation 4 condenser capsules pressure gradient receives
Frequency Range 20-20kHz
Sensitivity at 1000Hz 045mVubar ~ 45mVPa - 61 5dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level Approx 26dB (filter CCITT-CDIN45405)
Weighted Noise Level Approx 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB(20 to 10kHz) ~ 40dB(20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dBs PL
Admissible Climatic Conditions Temperature range (-20deg C - 4deg F to 60 deg C148deg F) Relative Humidity (99 at 20 degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via remote control unit S42E
Current Consumption 5mA maximum for each channel
Dimensions 33265mm(1 29104 in) 0 x 196mm(792 in) in length
Connector Type 12-pin minature DIN-plug
Finish Satin-black chromium-plated all-metal housing
Weight 280g(988 oz)
Included Accessories W34 foam windscreen H156 elastic suspenshysion ind ividual frequency curves MK4220 cable (20m) S42E remote control unit case
Recommended Accessories SA30 stand adaptor N62E power supply unit (2ch) N66E power supply unit (6ch)
AKG ACOUSTICS INC A NORTH AMERICAN PHILIPS COMPANY
77 Selleck Street Stamford CT 06902 (203) 348-2121
copyA KG ACOustics Inc 1980 Printed In U S A reg A KG Ak ustlsche und K ono-Gerate GmbH Austria
P roduct design and prices are subject to change without notice
Mode of Operation 2 condenser capsules pressure gradient receives
Frequency Range 20 to 20kHz
Sensitivity at 1000Hz 045mVubar (4 5mVPa) - 67dBV on op~n circuit - 46dB (1mW10 dynescm )
Electrical Impedance lt 200 ohms plusmn 20 (outputs ground free balanced)
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level 26dB SPL (filter CCITT-CDIN45405)
Weighted Noise Level 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsuleS)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dB s PL
Admissible Climatic Conditions Temperature range (- 20deg _ 4deg F to 60 deg
C148deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DI N45596
Current Consumption Channel 1-approx 5mA Channel 2-approx 2mA
Dimensions 3225mm(1 25 98 in) o x 200mm (7 87 in) length
Built-in Connector 5 pin XLR type
Finish Satin-black chromium-plated all-metal housing
Weight 300g (1059 oz)
Included Accessories W34 foam windscreen H 156 elastic suspen shysion individual frequency curves case
Recomended Accessories MK332020m (65ft) mic cable N62E power supply unit for one stereo mic N66E power supply unit for 3 stereo mics
21 -181middot5HS
--
+10 t--- shyo dB
- 10
~V 1m ( rv 3 114 ) ON AXIS AND 180 OFF AXIS AT B (FIGURE - 8) SET TING OF PATTERN -SELECTOR
SWITCH
MINIMUM REJECTI ON AT 75 -105deg OFF AXIS +3dB DE VIATION ALLOWABLE
WITH IN ANY ONE OC TAVE
50 100 200 500 1000 2000 5000
FREQUENCY AND POLAR RESPONSE CURVES
C33 CARDIOID +20
+10
o dB
2OH
- middot( 1)middot 00- 1 bull bull
Im ( V3 - 14 ) ON A X I S -t--t-t- r--
MIN IMUM REJECTION AT laomiddot OFF AXI S + 3dB DE VIATI ON ALLOWABLE WI THIN ANY
ONE OC TAVE
-
50 100 200 500 1000 2000 5000 10 000 20000
90i-++t-+-H H-+-H--I-I90middot
-10
-20
2000 He 250Hc 4000 HI 500H z 8000 HI
1000 H I __ I6DOCH I
125 Hz
C34 OMNI +10
o dB
- 10
-20
20Hz
CARDIOID +20
+10
o dB
- 10
-20
20Hz
FIGURE 8 +20
+10
o dB
-10
-20
J J~_h ( ~ IOII - IQi-I1
- 1m ( 3 -11 4 ) ON AXI S AT 0 (OMNIDIR ECT IONAL) shySETTING OF PATTERN-SELECTOR SWITCH
90deg1-++-I+ H H-+-H +-I90middot
125 H 2000 Hz __ 250Hz -- 4000 Hz-t
500 Hz 8000 Hz 100 200 500 1000 2000 5000 10000 20000 1000 H l _ _ I SeOO HI
~ -~) bullbull It1l I-IOII~I 1
m ( V3 - 114)ON AXIS AT Q (CA RDI OID) fshy SETTI NG OF PATT ERN -SELE CTOR SWITCH
ANY ONE OC TAVE
12 5H z -- 2000Hz -- 250Hz --- 4000Hz
500 HI 8 000 Hz 100 200 500 1000 2000 5000 10 000 20000 1000 Hz _ _ 16DOCH I
-~ l iIII -IV_-Ili llm ( 3 -14) ON AXIS AND 18 0 0 OFF AXIS AT 8(FIGURE - 8) SE TTiN G OF PA TTE RN-SELE CTO R SWIT CH
90deg1-+-H~H H ---laquoH -H90
+- tshy~
12 5 H1
250 Hz -- ~ggg~~ 500 Hz 8000 Hz
100 200 500 1000 2000 5000 10000 20000 100 0 Hz __ 16eOCHz
C422 OMNI +10
o dB
- 10
-20
20Hz
CARDIOID +20
20Hz
FIGURE 8 + 20
-20
20 Hz
- 1m (-3-114) ON AX IS AT 0 (OMNIOIRECTIONAL SETTING OF PATTERN- SELE CTOR SWIT CH
50 100 200 500 1000 2000 5000
50
=shy+10
o dB
-10
-20
1- VIm ( V 3 -14 ) ON AXIS AT Gl (CARDIOID) U ~ bull uIC~ID~ co- IN
SETTING OF PATTERN-SELECTOR SWITCH f shy
bshy~~
MIN REJECT ION AT lBO OFF AXIS +3dB DEV ALLOWABLE WITHIN ANY ONE OCTAVE - ~--
- f-shy
100 200 500 1000 2000 5000 10000 20 000
20 Hz
50
50
50
-f shy
90middotf+ +-++H
125 H 2000 HI 25 0 Hz --
30middot
4000Hl -- 500HZ 8000 HI
10000 20000 1000 Hz _ _ 16aOOHl
90 0H 4-H+r H+I+ H90middot
ut~jA I 0
900H+fcll+r J-i~H-H90middot
12 5 Hz -- 2000 HI 250 HI 4000 HI 500 Hz eooo HI
10000 20000 1000 Hz - - ISe OCHI
- MINIMUM REJEC TION AT 180 OFF AXIS --=l shy+3dB DEVIATI ON ALLOWABLE WITHIN
MINIMUM REJE CTI ON AT 75middot- 105 OFF AXIS +3dB_ DEVIATION ALLOWABLE WITHIN ANY ONE OCTAVE
BLOCK DIAGRAMS C422C34
I
I
---
t
12V ----~-
I Kshy MK 42120
Mshy
0shy ch 1 f----i S 42 E
cshy ch2
Jshy
BshyI
) Ashy
C33 - _--- XLR-Sshy
--+----+-0 2
1 1
1 I Channel l Chunnel l -------+-03 I
I I I I I I I I I I
I I
i Ch anne l 2 Channel 2 1 I I I laquo11 plusmn
DIMENSION DIAGRAMS 1-58
C422
r---- 4-34--- -1
~------8-1316 ------ shy
1-1132
C34 --l -c=c[JJ]---~ml15i31
65 1~---4-114 I I 7-916
C33 11132 1-3116
knn~fGIII~L____==ll I I I1----4114-----1 I
I 7916
SPECIFICATIONSmiddotC33 SPECIFICATIONSmiddotC422 SPECIFICA TlONSmiddotC34
Mode of Operation 2 twin diaphragm systems pressure gradient receivers
Frequency Range 20-20kHz
Sensitivity at 1000Hz 6mVPa - 645dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~500 ohms
Equivalent Noise Level lt 22dB (filter CCITT-C DIN45405)
Weighted Noise Level Approx 16uV RMS (filter CCITT-C DIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 5uV5uT
Max Sound Pressure Level (for 1000Hz) and 500 ohms load Impedance harmonic distortion k = 05 ) 92Pa ~ 133 dB SPL
Admissible Climatic Conditions Temperature Range (- 20degC- 4 deg to 60degC148 deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via S42E with phantom power supply
Current Consumption 5mA max for misc (each ch ) Approx 50mA for LED s
Dimensions 3342 mm (129165 in) 0 x 235mm (9 25 in) in length
Connector Type 12 pica miniature DIN plug
Finish Satin-black chromium -plated all-metal housing
Weight Approx 430g (1518 oz)
Included Accessories W42 foam wind shyscreen H159 elastic suspension MK4220 cable (20m) S42E remote control unit individual frequency curves case
Recommended Accessories SA42 stand adapter H42 suspenshysion ring N62E power supply unit (2ch) N66E power supply unit (6ch)
Mode of Operation 4 condenser capsules pressure gradient receives
Frequency Range 20-20kHz
Sensitivity at 1000Hz 045mVubar ~ 45mVPa - 61 5dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level Approx 26dB (filter CCITT-CDIN45405)
Weighted Noise Level Approx 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB(20 to 10kHz) ~ 40dB(20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dBs PL
Admissible Climatic Conditions Temperature range (-20deg C - 4deg F to 60 deg C148deg F) Relative Humidity (99 at 20 degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via remote control unit S42E
Current Consumption 5mA maximum for each channel
Dimensions 33265mm(1 29104 in) 0 x 196mm(792 in) in length
Connector Type 12-pin minature DIN-plug
Finish Satin-black chromium-plated all-metal housing
Weight 280g(988 oz)
Included Accessories W34 foam windscreen H156 elastic suspenshysion ind ividual frequency curves MK4220 cable (20m) S42E remote control unit case
Recommended Accessories SA30 stand adaptor N62E power supply unit (2ch) N66E power supply unit (6ch)
AKG ACOUSTICS INC A NORTH AMERICAN PHILIPS COMPANY
77 Selleck Street Stamford CT 06902 (203) 348-2121
copyA KG ACOustics Inc 1980 Printed In U S A reg A KG Ak ustlsche und K ono-Gerate GmbH Austria
P roduct design and prices are subject to change without notice
Mode of Operation 2 condenser capsules pressure gradient receives
Frequency Range 20 to 20kHz
Sensitivity at 1000Hz 045mVubar (4 5mVPa) - 67dBV on op~n circuit - 46dB (1mW10 dynescm )
Electrical Impedance lt 200 ohms plusmn 20 (outputs ground free balanced)
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level 26dB SPL (filter CCITT-CDIN45405)
Weighted Noise Level 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsuleS)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dB s PL
Admissible Climatic Conditions Temperature range (- 20deg _ 4deg F to 60 deg
C148deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DI N45596
Current Consumption Channel 1-approx 5mA Channel 2-approx 2mA
Dimensions 3225mm(1 25 98 in) o x 200mm (7 87 in) length
Built-in Connector 5 pin XLR type
Finish Satin-black chromium-plated all-metal housing
Weight 300g (1059 oz)
Included Accessories W34 foam windscreen H 156 elastic suspen shysion individual frequency curves case
Recomended Accessories MK332020m (65ft) mic cable N62E power supply unit for one stereo mic N66E power supply unit for 3 stereo mics
21 -181middot5HS
BLOCK DIAGRAMS C422C34
I
I
---
t
12V ----~-
I Kshy MK 42120
Mshy
0shy ch 1 f----i S 42 E
cshy ch2
Jshy
BshyI
) Ashy
C33 - _--- XLR-Sshy
--+----+-0 2
1 1
1 I Channel l Chunnel l -------+-03 I
I I I I I I I I I I
I I
i Ch anne l 2 Channel 2 1 I I I laquo11 plusmn
DIMENSION DIAGRAMS 1-58
C422
r---- 4-34--- -1
~------8-1316 ------ shy
1-1132
C34 --l -c=c[JJ]---~ml15i31
65 1~---4-114 I I 7-916
C33 11132 1-3116
knn~fGIII~L____==ll I I I1----4114-----1 I
I 7916
SPECIFICATIONSmiddotC33 SPECIFICATIONSmiddotC422 SPECIFICA TlONSmiddotC34
Mode of Operation 2 twin diaphragm systems pressure gradient receivers
Frequency Range 20-20kHz
Sensitivity at 1000Hz 6mVPa - 645dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~500 ohms
Equivalent Noise Level lt 22dB (filter CCITT-C DIN45405)
Weighted Noise Level Approx 16uV RMS (filter CCITT-C DIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 5uV5uT
Max Sound Pressure Level (for 1000Hz) and 500 ohms load Impedance harmonic distortion k = 05 ) 92Pa ~ 133 dB SPL
Admissible Climatic Conditions Temperature Range (- 20degC- 4 deg to 60degC148 deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via S42E with phantom power supply
Current Consumption 5mA max for misc (each ch ) Approx 50mA for LED s
Dimensions 3342 mm (129165 in) 0 x 235mm (9 25 in) in length
Connector Type 12 pica miniature DIN plug
Finish Satin-black chromium -plated all-metal housing
Weight Approx 430g (1518 oz)
Included Accessories W42 foam wind shyscreen H159 elastic suspension MK4220 cable (20m) S42E remote control unit individual frequency curves case
Recommended Accessories SA42 stand adapter H42 suspenshysion ring N62E power supply unit (2ch) N66E power supply unit (6ch)
Mode of Operation 4 condenser capsules pressure gradient receives
Frequency Range 20-20kHz
Sensitivity at 1000Hz 045mVubar ~ 45mVPa - 61 5dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level Approx 26dB (filter CCITT-CDIN45405)
Weighted Noise Level Approx 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB(20 to 10kHz) ~ 40dB(20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dBs PL
Admissible Climatic Conditions Temperature range (-20deg C - 4deg F to 60 deg C148deg F) Relative Humidity (99 at 20 degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via remote control unit S42E
Current Consumption 5mA maximum for each channel
Dimensions 33265mm(1 29104 in) 0 x 196mm(792 in) in length
Connector Type 12-pin minature DIN-plug
Finish Satin-black chromium-plated all-metal housing
Weight 280g(988 oz)
Included Accessories W34 foam windscreen H156 elastic suspenshysion ind ividual frequency curves MK4220 cable (20m) S42E remote control unit case
Recommended Accessories SA30 stand adaptor N62E power supply unit (2ch) N66E power supply unit (6ch)
AKG ACOUSTICS INC A NORTH AMERICAN PHILIPS COMPANY
77 Selleck Street Stamford CT 06902 (203) 348-2121
copyA KG ACOustics Inc 1980 Printed In U S A reg A KG Ak ustlsche und K ono-Gerate GmbH Austria
P roduct design and prices are subject to change without notice
Mode of Operation 2 condenser capsules pressure gradient receives
Frequency Range 20 to 20kHz
Sensitivity at 1000Hz 045mVubar (4 5mVPa) - 67dBV on op~n circuit - 46dB (1mW10 dynescm )
Electrical Impedance lt 200 ohms plusmn 20 (outputs ground free balanced)
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level 26dB SPL (filter CCITT-CDIN45405)
Weighted Noise Level 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsuleS)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dB s PL
Admissible Climatic Conditions Temperature range (- 20deg _ 4deg F to 60 deg
C148deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DI N45596
Current Consumption Channel 1-approx 5mA Channel 2-approx 2mA
Dimensions 3225mm(1 25 98 in) o x 200mm (7 87 in) length
Built-in Connector 5 pin XLR type
Finish Satin-black chromium-plated all-metal housing
Weight 300g (1059 oz)
Included Accessories W34 foam windscreen H 156 elastic suspen shysion individual frequency curves case
Recomended Accessories MK332020m (65ft) mic cable N62E power supply unit for one stereo mic N66E power supply unit for 3 stereo mics
21 -181middot5HS
SPECIFICATIONSmiddotC33 SPECIFICATIONSmiddotC422 SPECIFICA TlONSmiddotC34
Mode of Operation 2 twin diaphragm systems pressure gradient receivers
Frequency Range 20-20kHz
Sensitivity at 1000Hz 6mVPa - 645dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~500 ohms
Equivalent Noise Level lt 22dB (filter CCITT-C DIN45405)
Weighted Noise Level Approx 16uV RMS (filter CCITT-C DIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 5uV5uT
Max Sound Pressure Level (for 1000Hz) and 500 ohms load Impedance harmonic distortion k = 05 ) 92Pa ~ 133 dB SPL
Admissible Climatic Conditions Temperature Range (- 20degC- 4 deg to 60degC148 deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via S42E with phantom power supply
Current Consumption 5mA max for misc (each ch ) Approx 50mA for LED s
Dimensions 3342 mm (129165 in) 0 x 235mm (9 25 in) in length
Connector Type 12 pica miniature DIN plug
Finish Satin-black chromium -plated all-metal housing
Weight Approx 430g (1518 oz)
Included Accessories W42 foam wind shyscreen H159 elastic suspension MK4220 cable (20m) S42E remote control unit individual frequency curves case
Recommended Accessories SA42 stand adapter H42 suspenshysion ring N62E power supply unit (2ch) N66E power supply unit (6ch)
Mode of Operation 4 condenser capsules pressure gradient receives
Frequency Range 20-20kHz
Sensitivity at 1000Hz 045mVubar ~ 45mVPa - 61 5dBV on no-load operation
Electrical Impedance 200 ohms plusmn 20 balanced floating
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level Approx 26dB (filter CCITT-CDIN45405)
Weighted Noise Level Approx 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB(20 to 10kHz) ~ 40dB(20 to 15kHz) (measured without capsules)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dBs PL
Admissible Climatic Conditions Temperature range (-20deg C - 4deg F to 60 deg C148deg F) Relative Humidity (99 at 20 degC- 4degF)
Supply Voltage 9-52V according to DIN45596 via remote control unit S42E
Current Consumption 5mA maximum for each channel
Dimensions 33265mm(1 29104 in) 0 x 196mm(792 in) in length
Connector Type 12-pin minature DIN-plug
Finish Satin-black chromium-plated all-metal housing
Weight 280g(988 oz)
Included Accessories W34 foam windscreen H156 elastic suspenshysion ind ividual frequency curves MK4220 cable (20m) S42E remote control unit case
Recommended Accessories SA30 stand adaptor N62E power supply unit (2ch) N66E power supply unit (6ch)
AKG ACOUSTICS INC A NORTH AMERICAN PHILIPS COMPANY
77 Selleck Street Stamford CT 06902 (203) 348-2121
copyA KG ACOustics Inc 1980 Printed In U S A reg A KG Ak ustlsche und K ono-Gerate GmbH Austria
P roduct design and prices are subject to change without notice
Mode of Operation 2 condenser capsules pressure gradient receives
Frequency Range 20 to 20kHz
Sensitivity at 1000Hz 045mVubar (4 5mVPa) - 67dBV on op~n circuit - 46dB (1mW10 dynescm )
Electrical Impedance lt 200 ohms plusmn 20 (outputs ground free balanced)
Normal Load Impedance ~ 500 ohms
Equivalent Noise Level 26dB SPL (filter CCITT-CDIN45405)
Weighted Noise Level 18uV RMS (filter CCITT-CDIN45405)
Crosstalk Attenuation ~ 70dB (20 to 10kHz) ~ 40dB (20 to 15kHz) (measured without capsuleS)
Magnetic Field Interference Factor (at 50Hz) 35uV5uT
Max Sound Pressure Level (for 1000Hz and 500 ohms load impedance harmonic distortion k = 05 ) 80Pa ~ 132 dB s PL
Admissible Climatic Conditions Temperature range (- 20deg _ 4deg F to 60 deg
C148deg F) Relative Humidity (99 at 20degC- 4degF)
Supply Voltage 9-52V according to DI N45596
Current Consumption Channel 1-approx 5mA Channel 2-approx 2mA
Dimensions 3225mm(1 25 98 in) o x 200mm (7 87 in) length
Built-in Connector 5 pin XLR type
Finish Satin-black chromium-plated all-metal housing
Weight 300g (1059 oz)
Included Accessories W34 foam windscreen H 156 elastic suspen shysion individual frequency curves case
Recomended Accessories MK332020m (65ft) mic cable N62E power supply unit for one stereo mic N66E power supply unit for 3 stereo mics
21 -181middot5HS
top related