ar standing seam - agway metals inc
Post on 02-Jan-2022
2 Views
Preview:
TRANSCRIPT
0.5VARIABLE
1.0PAINTED SURFACE
VARIABLE 0.51
1.5PAINTEDSURFACE
VARIABLE 0.71
2.0PAINTEDSURFACE
4 (102)
2 (51)
1 3/4(45)
3/8 (10)
60°
1 1/2(38)
1/4 (6)
Clip attaches with fasteners here
Batten
Open 1/16”
tight
tight
Tool End View:
Material: 18 ga. galvanized
6”1.25”
1”1.5”
22”
Cut 1” out of both vertical ribs.
Apply Hand Folder to panel edge as shown and bend down.
After installation, the edge may be closed over Starter with wide-jaw pliers.Protect inside of pliers to avoid damage to pre-painted steel.
OPERATING SEQUENCE:
This tool is available from Agway Metals Inc.
1
2
3
4
5
6
AR Standing Seam
Dimensions & SpecificationsOptional Batten Cap & Assembly
AR-25/38/50 Hemming Tool
Mar. 2021
FEATURES: • No exposed fasteners • Ease of installation • Full range of stock colours • Variable width • Optional stiffening flutes • Concealed hold-down clips • Knee Caps available • Optional two-piece expansion clip to accommodate roof movement • 24 gauge can be seamed 90° and 180°; 22 gauge can be seamed 90° only • Butyl Tape is recommended in 90° seams • Able to be curved - minimum sheet length 5’-0”
AR-25 AR-38 AR-50
24/22 ga. 21” 20” 18.5”
AR-25
AR-38
AR-50STIFFENING FLUTES OPTIONAL
Panel Specifications
Standard Panel Widths
Min./Max. Min./Max. Min./Max. Min./Max. Slope Material Sheet Panel Thickness Length* Width
AR-25: 3/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28” AR-38: 1.5/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28”
AR-50: 0.5/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28”
*NOTES: Longer sheets are available on request. Additional charges may apply. Side lap caulking is recommended when the slope is less than 2/12
OIL CANNING: • Oil canning may be present due to various factors. Oil canning is not a valid reason for rejection of this product.
AR-38 Break Formed Batten Cap, 26 ga. Finish to match roofing panels. Available in lengths up to 20’-2”. Batten Cap must be secured at Ridge and Hip areas.
AR-38 Batten Clip 18 ga. Galvanized. Maximum 48” on centre. Install using (2) fasteners w/washers per clip.
ROOF ASSEMBLYAR Roof Panel
Membraneon Solid Substrate AR Clip
AR-25, 38 & 50 Metal Roof Panel
Section AA
Breathable Water Barrier
Rigid Insulation & Sub-Girt
Air/Vapour Barrier (Peel & Stick)Densdek 1/2”Steel Deck or Solid Substrate
AR Roof Clip
AR Roof Clip
Double Fold Single Fold
Plain Fluted
A
A
AR-25, 38 & 50 Metal Roof Panel
Breathable Water Barrier
Rigid Insulation & Sub-Girt
Air/Vapour BarrierDensdek 1/2”Steel Deck or Solid Substrate
Installation
Hold-down Clip Detail
AR-38 Mist Green
AR Standing Seam
Typical Installation on Solid Substrate
Typical Installation on Insulated Roof
FIXED CLIP EXPANSION CLIP
90° Seaming Stages T-Style 22 & 24 Gauge 180° Seaming Stages I-Style 24 Gauge only
Overlap Seaming Options
Overlap prior to seaming.
• Single skin application • Recommended that this always be applied over solid substrate • Recommended that this be applied over waterproof membrane • Clips at maximum 2’ centres - 2 fasteners per clip • Mechanical and Hand Seamer required
CRC Barrel 400 mm SSR Panels 24 ga. Mist Green
AR-38 Galvalume Plus
0.5VARIABLE
1.0PAINTED SURFACE
VARIABLE 0.51
1.5PAINTEDSURFACE
VARIABLE 0.71
2.0PAINTEDSURFACE
4 (102)
2 (51)
1 3/4(45)
3/8 (10)
60°
1 1/2(38)
1/4 (6)
Clip attaches with fasteners here
Batten
Open 1/16”
tight
tight
Tool End View:
Material: 18 ga. galvanized
6”1.25”
1”1.5”
22”
Cut 1” out of both vertical ribs.
Apply Hand Folder to panel edge as shown and bend down.
After installation, the edge may be closed over Starter with wide-jaw pliers.Protect inside of pliers to avoid damage to pre-painted steel.
OPERATING SEQUENCE:
This tool is available from Agway Metals Inc.
1
2
3
4
5
6
AR Standing Seam
Dimensions & SpecificationsOptional Batten Cap & Assembly
AR-25/38/50 Hemming Tool
Mar. 2021
FEATURES: • No exposed fasteners • Ease of installation • Full range of stock colours • Variable width • Optional stiffening flutes • Concealed hold-down clips • Knee Caps available • Optional two-piece expansion clip to accommodate roof movement • 24 gauge can be seamed 90° and 180°; 22 gauge can be seamed 90° only • Butyl Tape is recommended in 90° seams • Able to be curved - minimum sheet length 5’-0”
AR-25 AR-38 AR-50
24/22 ga. 21” 20” 18.5”
AR-25
AR-38
AR-50STIFFENING FLUTES OPTIONAL
Panel Specifications
Standard Panel Widths
Min./Max. Min./Max. Min./Max. Min./Max. Slope Material Sheet Panel Thickness Length* Width
AR-25: 3/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28” AR-38: 1.5/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28”
AR-50: 0.5/12 - 12/12 0.024 - 0.030 in. 2’-6” – 45’ 10” – 28”
*NOTES: Longer sheets are available on request. Additional charges may apply. Side lap caulking is recommended when the slope is less than 2/12
OIL CANNING: • Oil canning may be present due to various factors. Oil canning is not a valid reason for rejection of this product.
AR-38 Break Formed Batten Cap, 26 ga. Finish to match roofing panels. Available in lengths up to 20’-2”. Batten Cap must be secured at Ridge and Hip areas.
AR-38 Batten Clip 18 ga. Galvanized. Maximum 48” on centre. Install using (2) fasteners w/washers per clip.
top related