ata 49 apu (apic)
Post on 03-Dec-2014
1.021 Views
Preview:
TRANSCRIPT
A319/A320/A321TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE
49 APU (APIC)
This document must be used for training purpose only
Under no circumstances should this document be used as a reference.
It will not be updated.
All rights reserved.No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,without the prior written permission of Airbus Industrie.
** APU Presentation (1) 1..........................
** APU Controls Presentation (1) 7.................
** APU ECAM Page Presentation (1) 13...............
** APU Installation Presentation (2) 21...........
APU Drain System Presentation (2) 29...............
APU Basic Description (3) 33.......................
** APU Fuel Feed System D/O (3) 43.................
** APU Ignition and Starting D/O (3) 47...........
** Fuel System Description/Operation (3) 51.......
** Oil System Description/Operation (3) 57........
** Air System Description/Operation (3) 63........
** APU System Management (3) 69....................
APU Warnings (3) 77.................................
** ECB Interfaces (3) 81............................
** Fuel System Components (3) 85...................
** Oil System Components (3) 99....................
** Air System Components (3) 119...................
** Miscellaneous System Components (3) 133........
MAINTENANCE PRACTICES** COMPT Access Doors Operation (2) 151...........** APU Removal / Installation (3) 155.............SPECIFIC PAGES** CFDS Specific Page Presentation (3) 165......
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
EFFECTIVITYALL
49 APU (APIC)
UFD4200 TABLE OF CONTENTS Page
CONTENTSPage i
Dec 31/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
EFFECTIVITYALL
49 APU (APIC)
UFD4200 TABLE OF CONTENTS Page
CONTENTSPage ii
Dec 31/00
THIS PAGE INTENTIONALLY LEFT BLANK
49 - APU
49-00-00 APU PRESENTATION
CONTENTS:GeneralEngineOilFuelAirIgnition and StartingControl and MonitoringAC GeneratorSelf Examination
TMUAPAB01 LEVEL 1
EFFECTIVITY 49-00-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 1EFFECTIVITYALL
APU PRESENTATION
GENERAL
The APU, installed in the fuselage tail cone in a fireproof compartment, is an independent source ofpneumatic and electrical power.It can be used in flight and on ground.The compressed air is used to supply the :
- Environmental Control System (ECS).- Main Engine Start (MES).- Anti icing.
The APU is a Model APS 3200 manufactured and designedby Auxiliary Power International Corps (APIC).
ENGINE
The APU is a single spool gas turbine engine whichdrives a load compressor and an accessory gearbox.The engine is composed of:
- a single stage centrifugal compressor.- a reverse flow combustion chamber.- a two stage axial flow turbine.
The combustion chamber is equipped with 9 fuel nozzlesand two ignitor plugs.
OIL
The Oil system is monitored by the Electronic ControlBox which receives temperature, pressure and quantitysignalsThe self contained oil system lubricates, cleans andcools the APU bearings and accessory gearbox with thesame oil types as approved for the main engines.The oil is also used to cool and lubricate the gearboxmounted AC generator.
FUEL
The APU is supplied with fuel from either the fuelfeed system pump or the fuel tank pumps, according tothe pressure sensed in the APU fuel feed line. TheFuel Control Unit (FCU) is the main component of thefuel system.The Electronic Control Box (ECB) computes the fuel/airratio, corresponding to the APU load, and meters thefuel flow accordingly. Fuel pressure is also used asmuscle pressure to operate the load compressor InletGuide Vane (IGV) actuator and the Bleed Control Valve(BCV).
AIR
The main role of the air system is to supply bleed airto the pneumatic system while avoiding compressorsurge.The air system includes a Bleed Control Valve, InletGuide Vanes to control the airflow into the loadcompressor in order to avoid overtemperature of thepower section. Control and operation of thesecomponents are assumed by the Electronic Control Box.
IGNITION AND STARTING
The APU start sequence is initiated from the cockpitand is controlled by the Electronic Control Box.During starting, the electrical starter motor drivesthe APU rotating assembly through a clutch and thegear train in the gearbox, it disengages at 55% speed.Initial combustion is ensured by the ignition Unit andthe ignitors.T
MUAPAB01-T01 LEVEL 1
EFFECTIVITY 49-00-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 2EFFECTIVITYALL
APU PRESENTATIONTMUAPAB01-P01 LEVEL 1
EFFECTIVITY 49-00-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 3EFFECTIVITYALL
APU PRESENTATION
CONTROL AND MONITORING
The APU engine control system has manual and automaticcontrols to start, shutdown and keep the APU in safelimits during operation.The Electronic Control Box (ECB) which controls andmonitors the APU operation, is of the Full AuthorityDigital Electronic Controller (FADEC) type.The ECB has built in test equipment used for the powerup test and the monitoring test.The ECB also acts as interface between the aircraftand the APU.The ECB receives the APU Data and sends main parametersto the ECAM system.The parameters and the indications displayed on theAPU ECAM page are:
- Speed(N) and Exhaust Gas Temperature(EGT).- Bleed pressure, Inlet flap position, Low Oillevel and low fuel pressure.
- The APU AC Generator load, voltage andfrequency, through the electrical power system.
AC GENERATOR
An oil cooled APU Generator (90 KVA) can supply theaircraft electrical network.The APU AC generator, driven by the accessory gearbox, uses the APU shaft power to transform mechanicalpower into electrical power which is used by theaircraft systems.
TMUAPAB01-T02 LEVEL 1
EFFECTIVITY 49-00-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 4EFFECTIVITYALL
TMUAPAB01-P02 LEVEL 1
APU PRESENTATION
EFFECTIVITY 49-00-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 5EFFECTIVITYALL
SELF EXAMINATION
What is the main function of the APU ? A - To produce independent pneumatic and
hydraulic power. B - To produce independent pneumatic and
electrical power. C - To produce independent electrical and
hydraulic power.
Which component controls and monitors the APU ? A - The Electronic Control Box. B - The Fuel Control Unit. C - The IGV Control Unit.
The Electronic Control Box has : A - Restricted authority over APU operation. B - Only APU monitoring function. C - Full authority over APU operation.
TMUAPAB01 LEVEL 1
EFFECTIVITY 49-00-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 6EFFECTIVITYALL
49 - APU
49-60-00 APU CONTROLS PRESENTATION
CONTENTS:GeneralOverhead PanelExternal Power Control PanelSelf Examination
TMUAPA401 LEVEL 1
EFFECTIVITY 49-60-00 Page 1May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 7EFFECTIVITYALL
APU CONTROLS PRESENTATION
GENERAL
Normal control of the APU is carried out from theAPU control panel located in the cockpit. Emergencyshut down can be performed on ground from outside theaircraft.
OVERHEAD PANEL
MASTER SWITCHThe master switch pushbutton when pressed in, controlsthe power supply for APU operation and protection.A normal shutdown sequence is initiated when themaster switch is released out.The ON light comes on blue when the Master switch P/Bis pressed in and the APU page appears on the ECAMsystem display.The FAULT light comes on amber and the correspondingwarnings are activated when an automatic shutdownoccurs.
START PUSHBUTTONThe start pushbutton initiates the APU start sequence.The ON light comes on blue until 95% N(RPM).The AVAIL light comes on green above 95% N(RPM).
APU FIRE PUSH BUTTONWhen the APU fire pushbutton is released out, an APUemergency shutdown is initiated.
TMUAPA401-T01 LEVEL 1
EFFECTIVITY 49-60-00 Page 2May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 8EFFECTIVITYALL
APU CONTROLS PRESENTATIONTMUAPA401-P01 LEVEL 1
EFFECTIVITY 49-60-00 Page 3May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 9EFFECTIVITYALL
APU CONTROLS PRESENTATION
EXTERNAL POWER CONTROL PANEL
APU SHUT OFF PUSHBUTTONAn APU emergency shutdown can be performed using theAPU SHUT OFF pushbutton located on the externalpower control panel, next to the nose landing gear.Operation of the APU SHUT OFF pushbutton cancels theground horn.
APU FIRE LIGHTThe APU FIRE red light comes on when a fire is detectedon ground and is accompanied by the ground horn. (APUshutdown and Auto extinguishing in this case).
TMUAPA401-T02 LEVEL 1
EFFECTIVITY 49-60-00 Page 4May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 10EFFECTIVITYALL
TMUAPA401-P02 LEVEL 1
APU CONTROLS PRESENTATION
EFFECTIVITY 49-60-00 Page 5May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 11EFFECTIVITYALL
SELF EXAMINATION
From where can an APU emergency shutdown beperformed ?
A - Refuel/defuel panel,external controlpanel and cockpit.
B - APU Fire panel, external power controlpanel.
C - The APU cannot be shutdown from outsidethe aircraft.
Normal APU shutdown is performed from ?A - Fire panel.B - External power control panel.C - APU control panel.
TMUAPA401 LEVEL 1
EFFECTIVITY 49-60-00 Page 6May 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 12EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-70-00 APU ECAM PAGE PRESENTATION
CONTENTS:GeneralExhaust Gas Temperature (EGT)SpeedFlap Open AvailableAPU GeneratorAPU BleedFuel Low PressureLow Oil Level
TMUAPA501 LEVEL 1
EFFECTIVITY 49-70-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 13EFFECTIVITYALL
APU ECAM PAGE PRESENTATION
GENERAL
The APU indications are displayed on the lower ECAMpage.This page is called manually or automatically duringAPU start.
EXHAUST GAS TEMPERATURE (EGT)
The Exhaust Gas Temperature is displayed green innormal configuration . This includes the pointer symboland digital indication.It pulses in advisory mode.It becomes red in case of over-temperature.A movable red line is computed by the ECB.The red EGTlimit value is different during APU starting and whenAPU becomes available.
SPEED
The speed indication is displayed in green.It becomes amber or red in case of overspeed.
FLAP OPEN
The green FLAP OPEN indication is displayed when theair intake flap is fully open.No indication is displayed otherwise.
- FLAP OPEN displayed steady: Air intake flapfully open with the MASTER SW pushbutton setto ON.
- FLAP OPEN displayed pulsing: Air intake flapnot fully closed 3 minutes after the MASTER SWpushbutton has been set to OFF.
AVAIL
When the APU is running, a green APU AVAILableindication appears on the upper ECAM page.The green AVAILable indication is displayed whenthe APU speed is above 95%.Nothing is displayed otherwise.
TMUAPA501-T01 LEVEL 1
EFFECTIVITY 49-70-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 14EFFECTIVITYALL
APU ECAM PAGE PRESENTATIONTMUAPA501-P01 LEVEL 1
EFFECTIVITY 49-70-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 15EFFECTIVITYALL
APU ECAM PAGE PRESENTATION
APU GENERATOR
The APU electrical generator output is displayed asshown on the picture.The APU generator parameters are displayed amber incase of overload, or if voltage or frequency are outof range.
TMUAPA501-T02 LEVEL 1
EFFECTIVITY 49-70-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 16EFFECTIVITYALL
TMUAPA501-P02 LEVEL 1
APU ECAM PAGE PRESENTATION
EFFECTIVITY 49-70-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 17EFFECTIVITYALL
APU ECAM PAGE PRESENTATION
APU BLEED
The APU BLEED indication is displayed in green on theupper ECAM memo page during APU BLEED supply .The APU bleed pressure indication is replaced by ambercrosses when the indication is not available.
FUEL LOW PRESS.
The FUEL LOw PRessure indication is displayed when thepressure upstream from the fuel control unit is toolow.
- The amber FUEL LO PR message is displayed whenthe fuel pressure,in the APU fuel feed line,isbelow 15 PSI.
LOW OIL LEVEL
The green LOW OIL LEVEL indication pulses when the oilin the gearbox reaches the low level and needsservicing.
- If the oil quantity decreases below 4 litres, the indication pulses on the APUECAM page.
TMUAPA501-T03 LEVEL 1
EFFECTIVITY 49-70-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 18EFFECTIVITYALL
TMUAPA501-P03 LEVEL 1
APU ECAM PAGE PRESENTATION
EFFECTIVITY 49-70-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 19EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPA501 LEVEL 1
EFFECTIVITY 49-70-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 20EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-10-00 APU INSTALLATION PRESENTATION
CONTENTS:GeneralMountsAir Intake FlapAir Intake DuctExhaustAccess DoorsDrain SystemSelf Examination
TMUAPAM01 LEVEL 2
EFFECTIVITY 49-10-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 21EFFECTIVITYALL
APU INSTALLATION PRESENTATION
GENERAL
The Auxiliary Power Unit is installed in a fireproofcompartment located in the fuselage tail cone.
MOUNTS
Seven tie rods attach the APU to the stucture bracketson the APU compartment ceiling.These tie rods alsoconnect to the APU three point mounted suspensionsystem.Vibration insulators are installed between the APUmount brackets and the tie rods to reduce thetransmission of aircraft vibrations and shocks to theAPU.The insulators also prevent the transmission ofvibrations from the APU to the aircraft structure.
TMUAPAM01-T01 LEVEL 2
EFFECTIVITY 49-10-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 22EFFECTIVITYALL
APU INSTALLATION PRESENTATIONTMUAPAM01-P01 LEVEL 2
EFFECTIVITY 49-10-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 23EFFECTIVITYALL
APU INSTALLATION PRESENTATION
AIR INTAKE FLAP
The air intake system ducts ambient air to the APUplenum chamber.An air intake flap cuts off the air supply when theAPU does not operate.In case of failure, the air intake flap can be openedor closed manually by a Manual Override Device.A fixed diverter increases the ram air recovery forflight operation and also prevents any fluids,flowingalong the fuselage, from entering the air intake.
AIR INTAKE DUCT
The air intake duct, which is composed of a diffuserand elbow, provides correct airflow to the APU plenum.The air intake duct is attached to the right accessdoor.
EXHAUST
The exhaust system lets the APU exhaust gas flow intothe atmosphere and muffles the noise from the exhaust.The exhaust muffler thermal insulation protects theaircraft structure.
TMUAPAM01-T02 LEVEL 2
EFFECTIVITY 49-10-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 24EFFECTIVITYALL
APU INSTALLATION PRESENTATIONTMUAPAM01-P02 LEVEL 2
EFFECTIVITY 49-10-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 25EFFECTIVITYALL
APU INSTALLATION PRESENTATION
ACCESS DOORS
Two access doors allow access to the APU compartment.The access doors on the bottom of the tailcone openoutwards to permit the APU to be inspected, lifted andlowered.
DRAIN SYSTEM
A drain system prevents the collection of fluids inthe APU compartment.Any fluid that may accumulate in the APU compartmentis delivered to a drain tank in the APU compartment,which is emptied through a drain mast when the aircraftis above 200 KTS.
TMUAPAM01-T03 LEVEL 2
EFFECTIVITY 49-10-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 26EFFECTIVITYALL
APU INSTALLATION PRESENTATIONTMUAPAM01-P03 LEVEL 2
EFFECTIVITY 49-10-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 27EFFECTIVITYALL
SELF EXAMINATION
On ground, in case of failure, how can you open orclose the air intake flap ?
A - The air intake flap actuator cannot beoveridden.
B - The air intake flap actuator can behydraulically overidden.
C - The air intake flap actuator can beoveridden by a Manual Override Device.
When is the drain tank emptied ?A - When the aircraft speed is above 200KTS. B - When the aircraft is stopped on the ramp.C - When the aircraft altitude is above 2000
feet.
TMUAPAM01 LEVEL 2
EFFECTIVITY 49-10-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 28EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-17-00 APU DRAIN SYSTEM PRESENTATION
CONTENTS:Fuel/Oil Pump Seal DrainBleed Control Valve Actuator DrainInlet Guide Vane Actuator DrainForward Bearing Seal DrainStart Fuel Manifold PurgeAir Bypass Plenum DrainExhaust Muffler DrainCombustion Chamber DrainDrain TankSelf Examination
TMUAPAG01 LEVEL 2
EFFECTIVITY 49-17-00 Page 1Nov 30/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 29EFFECTIVITYALL
APU DRAIN SYSTEM PRESENTATION
FUEL/OIL PUMP DRAIN
The fuel and oil pump seal drain line is routed via acollector line to the drain tank.This line drains fuel or oil leaks.
BLEED CONTROL VALVE ACTUATOR DRAIN
The Bleed Control Valve (BCV) actuator drain line isrouted via a collector line to the drain tank. Thisline drains only fuel leaks.
INLET GUIDE VANE ACTUATOR DRAIN
The Inlet Guide Vane (IGV) actuator drain line isrouted via a collector line to the drain tank. Thisline drains only fuel leaks.
FORWARD BEARING SEAL DRAIN
Any oil leak, from the forward bearing seal, flows tothe aircraft drain mast.
START FUEL MANIFOLD PURGE
The fuel which remains in the pilot injector andmanifold is purged to the APU exhaust diffuser.
AIR BYPASS PLENUM DRAIN
The air bypass plenum drain line is routed alone tothe drain mast.This drain line collects fuel or air leaks.
EXHAUST MUFFLER DRAIN
The exhaust muffler drain line is routed to the drainmast.This drain line collects fuel, water or air leaks.
COMBUSTION CHAMBER DRAIN
The combustion chamber drain line is routed to thedrain mast. This drain line collects unburnt fuel.
DRAIN TANK
For venting and evacuation the drain tank is connectedto the drain mast.Airflow across the drain mast creates a vacuum in thedrain line. The suction effect produced at 200 kt, issufficient to remove the contents of the drain tank.A vent line ventilates the drain tank and drain lines.The APU drain lines are connected to the right accessdoor drain lines through spring adapter seals (kissseals).
TMUAPAG01-T01 LEVEL 2
EFFECTIVITY 49-17-00 Page 2Nov 30/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 30EFFECTIVITYALL
APU DRAIN SYSTEM PRESENTATIONTMUAPAG01-P01 LEVEL 2
EFFECTIVITY 49-17-00 Page 3Nov 30/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 31EFFECTIVITYALL
SELF EXAMINATION
Which drains collect fuel, water and air ?A - Exhaust coupling drain.B - Flow divider drain.C - Air bypass plenum drain.
TMUAPAG01 LEVEL 2
EFFECTIVITY 49-17-00 Page 4Nov 30/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 32EFFECTIVITYALL
49 - APU
49-20-00 APU BASIC DESCRIPTION
CONTENTS:GeneralAir IntakeEngine ControlsEngineInlet guide vanesBleed and Surge AirOil SystemIgnition and StartingAccessory GearboxAC GeneratorFuel SystemSelf examination
TMUAPA801 LEVEL 3
EFFECTIVITY 49-20-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 33EFFECTIVITYALL
APU BASIC DESCRIPTION
GENERAL
The APU powerplant is installed in the fuselagetailcone. Tie rods attach the unit by a three-pointmounted suspension system to structure brackets on thecompartment ceiling in a fireproof compartment.A pair of access doors on the bottom of the tailconeopen outwards to permit the APU to be lifted andlowered.
AIR INTAKE SYSTEM
The air intake system ducts ambient air to the APUcompressor inlet.The air intake system includes :
- A fixed diverter which increases ram airrecovery for flight operation and also preventsany fluids, flowing along the fuselage, fromentering the air intake.
- An air intake with inlet flap.- An air inlet duct.
TMUAPA801-T01 LEVEL 3
EFFECTIVITY 49-20-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 34EFFECTIVITYALL
TMUAPA801-P01 LEVEL 3
APU BASIC DESCRIPTION
EFFECTIVITY 49-20-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 35EFFECTIVITYALL
APU BASIC DESCRIPTION
ENGINE CONTROLS
The Electronic Control Box (ECB) controls and monitorsthe APU operation. It is a full authority digitalelectronic controller (FADEC TYPE).The ECB has the following functions :
- control of the APU start sequence,- monitoring of the APU speed, exhaust gastemperature and bleed air supply,
- normal stop sequence and automatic emergencyshutdown malfunction indications for troubleshooting.
ENGINE
The APU is a single spool engine based on a modulardesign including a single shaft power section, drivinga single stage centrifugal load compressor and anaccessory gearbox.The APU is a single shaft assembly with :
- a single stage centrifugal compressor,- a reverse flow combustion chamber,- a two stage axial flow turbine.
INLET GUIDE VANES (IGV)
The Inlet Guide Vane assembly controls the amount ofair bled from the APU load compressor.The 24 Inlet Guide Vanes are moved simultaneously bya gear train operated by an actuator.The IGV system uses fuel as hydraulic fluid for theservovalve actuator to control the Inlet Guide Vanesthrough the ECB.
BLEED AND SURGE AIR
The bleed and surge air system provides air to theaircraft pneumatic system while avoiding loadcompressor surge.The Bleed Control Valve acts as a bleed and surgevalve, electrically controlled by the ECB and fueloperated.
OIL SYSTEM
A wet sump lubrication system cools and lubricatesthe electrical generator, the accessory gearbox andthe APU bearings.The system components are all located on thegearbox except the oil cooler which is located onthe APU left hand side.
IGNITION AND STARTING SYSTEM
The ignition and starting system rotates the engineto a self sustained speed. It also will start ignitionof the fuel/air mixture in the engine combustionchamber.The system includes :
- an electrical engine starter motor,- an ignition unit,- two igniter plugs.
TMUAPA801-T02 LEVEL 3
EFFECTIVITY 49-20-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 36EFFECTIVITYALL
APU BASIC DESCRIPTION
ACCESSORY GEARBOX
GEARBOX ASSEMBLYThe gearbox transmits the shaft power to the APUaccessories and to the APU generator which areinstalled on the gearbox pads.The gearbox is also the oil reservoir for the APUlubrication system.
ACCESSORIESThe components mounted on the accessory gearbox are :
- the Starter Motor Assembly,- the Cooling Air Fan Assembly with the PermanentMagnet Generator (PMG),
- the Oil Pump Assembly (lubrication unit),- the Fuel Control Unit,- the AC generator.
THE AC GENERATOR
The 3 phase AC generator transforms the mechanicalpower into electrical power (90 KVA) to supply theaircraft system (115V-400Hz).
TMUAPA801-T02 LEVEL 3
EFFECTIVITY 49-20-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 37EFFECTIVITYALL
TMUAPA801-P02 LEVEL 3
APU BASIC DESCRIPTION
EFFECTIVITY 49-20-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 38EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPA801 LEVEL 3
EFFECTIVITY 49-20-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 39EFFECTIVITYALL
APU BASIC DESCRIPTION
FUEL SYSTEM
The APU is supplied with fuel from either the fueltank pumps or the APU fuel feed system pump, accordingto the pressure sensed in the APU fuel feed line. TheAPU fuel system operates automatically and includes:
- an APU fuel feed pump, an APU inlet pressureswitch,
- a low Pressure Isolation Valve, - a Fuel Low Pressure switch, - a Fuel Control Unit (FCU) for fuel flowscheduling,
- a fuel line drain vent valve.
TMUAPA801-T03 LEVEL 3
EFFECTIVITY 49-20-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 40EFFECTIVITYALL
APU BASIC DESCRIPTION
TMUAPA801-P03 LEVEL 3
EFFECTIVITY 49-20-00 Page 9Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 41EFFECTIVITYALL
SELF EXAMINATION
Of what kind of design is the compressor ?A - Two stage centrifugal compressor design.B - Single stage centrifugal compressor
design. C - Two stage axial compressor design.
What are the main features of the AC generator ?A - 45 KVA, 115V, 50HZ.B - 90 KVA, 28 V.C - 90 KVA, 115V, 400HZ, 3 Phases.
What are the three APU modules ?A - Compressor, combustion chamber, turbine.B - Power section, load compressor, Fuel
Control Unit.C - Power section, load compressor,
accessory drive gearbox.
TMUAPA801 LEVEL 3
EFFECTIVITY 49-20-00 Page 10Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 42EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-31-00 APU FUEL FEED SYSTEM DESCRIPTION
CONTENTS:Fuel PumpFuel LP Isolation ValveAPU Inlet Low Pressure SensorFuel Drain Vent System
TMUAPA301 LEVEL 3
EFFECTIVITY 49-31-00 Page 1Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 43EFFECTIVITYALL
APU FUEL FEED SYSTEM DESCRIPTION
FUEL PUMP
The APU fuel pump is a centrifugal pump driven by asingle phase AC motor.This pump is controlled to run if the APU MASTER SWpushbutton is set to ON and the fuel crossfeed linepressure is not sufficient.The fuel crossfeed line pressure sensor controls theoperation of the APU fuel pump.The APU fuel pump runs as soon as the pump inletpressure is lower than 21.8 PSI.It stops when the pressure is above 23.2 PSI .
FUEL LP ISOLATION VALVE
The APU Fuel LP isolation valve is driven by two DCmotors.This valve is open as long as the MASTER SW pushbuttonis set to ON.When closed, it prevents pressurization of the APUfuel feed line and flow of fuel into a specific firezone.The APU Fuel LP isolation valve is automatically closedwhen:
- MASTER SW P/B is released out,- ECB protective shutdown occurs,- an APU shutdown occurs due to an APU fire,detected on ground,
- the APU FIRE P/B is released out (in thecockpit),
- the APU SHUT OFF P/B has been pressed on theexternal power receptacle panel.
APU INLET LOW PRESSURE SENSOR
At the inlet connection of the Fuel Control Unit , apressure sensor transmits low pressure informationthrough the ECB to the ECAM APU page.The FUEL LO PR message is displayed on the ECAM APUpage if it is selected and:
- the APU speed is greater than 7% RPM- the fuel pressure is lower than 15.8 PSI .
The ECB memorizes this information in its BITE memoryeven if the pressure increases above 17.3 PSI .
FUEL DRAIN / VENT SYSTEM
A vent APU fuel line pushbutton, located on thefirewall allows the APU fuel feed line to be purgedduring ground maintenance.As long as the pushbutton is held pressed in, the APUfuel LP isolation valve is open and the APU fuel pumpruns.A fuel drain and vent valve is installed in the APUcompartment at the fuel inlet connection to the FuelControl Unit. It permits fuel to be drained and airto be bled.
TMUAPA301-T01 LEVEL 3
EFFECTIVITY 49-31-00 Page 2Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 44EFFECTIVITYALL
APU FUEL FEED SYSTEM DESCRIPTIONTMUAPA301-P01 LEVEL 3
EFFECTIVITY 49-31-00 Page 3Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 45EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPA301 LEVEL 3
EFFECTIVITY 49-31-00 Page 4Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 46EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-40-00 APU IGNITION AND STARTINGDESCRIPTION AND OPERATION
CONTENTS :Starter ControlIgnition ControlSelf Examination
TMUAPA901 LEVEL 3
EFFECTIVITY 49-40-00 Page 1Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 47EFFECTIVITYALL
APU IGNITION AND STARTING DESCRIPTION AND OPERATION
STARTER CONTROL
The starting system drives the APU rotor through aclutch and gearbox.When the APU speed is 55% N, the start logic of theElectronic Control Box (ECB) cuts off the supply tothe start contactor which switches off the startermotor.The timed acceleration loop of the ECB causes the APUto accelerate to governed speed.
IGNITION CONTROL
The ignition system is used to ignite and maintaincombustion during the start phase.The ignition system includes:
- An Ignition Exciter Unit.- Two ignition leads.- Two igniter plugs.
The ignition system operates between 7% and 55% n.
TMUAPA901-T01 LEVEL 3
EFFECTIVITY 49-40-00 Page 2Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 48EFFECTIVITYALL
APU IGNITION AND STARTING DESCRIPTION AND OPERATIONTMUAPA901-P01 LEVEL 3
EFFECTIVITY 49-40-00 Page 3Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 49EFFECTIVITYALL
SELF EXAMINATION
Which component controls the ignition and startingoperation
A - The Electronic Control Box.B - The Ignition Exciter Unit.C - The Start Contactor.
TMUAPA901 LEVEL 3
EFFECTIVITY 49-40-00 Page 4Aug 31/95
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 50EFFECTIVITYALL
49 - APU
49-32-00 FUEL SYSTEM DESCRIPTION OPERATION
CONTENTS:GeneralFuel Control UnitFuel ScheduleMuscle PressureFuel Shut-OffFlow DividerFuel DistributionFuel DrainControlMonitoringSelf Examination
TMUAPAF01 LEVEL 3
EFFECTIVITY 49-32-00 Page 1Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 51EFFECTIVITYALL
FUEL SYSTEM DESCRIPTION OPERATION
GENERAL
The fuel system provides metered fuel to sustaincombustion.Part of the fuel is used as muscle pressure to operatethe Inlet Guide Vane actuator and the surge valveactuator.
FUEL CONTROL UNIT
The Fuel Control Unit has five functions:- fuel filtering,- pressure increase, - fuel metering,- positive fuel shut-off,- fuel muscle pressure regulation.
The Fuel Control Unit is composed of a low pressurefuel pump, a filter by-pass valve with a delta Pindicator, a high pressure fuel pump with a PressureRelief Valve, a constant delta P solenoid valve, apressure regulator (for bleed/surge valve and IGVactuators), a fuel metering valve, and the 3 waysolenoid valve.
FUEL SCHEDULE
The fuel metering valve is controlled by the ElectronicControl Box through a torque motor.The ECB schedules fuel flow for start sequence, onspeed operation and shutdown sequence.The Electronic Control Box modulates the on speed fuelschedule to match the aircraft demand for bleed airand electrical power.
MUSCLE PRESSURE
Fuel muscle pressure is used to operate the BleedControl Valve (BCV) actuator (air delivery to theaircraft and air discharge to the exhaust) and theload compressor Inlet Guide Vane (IGV) actuator.Servo fuel is returned downstream to the low pressurepump outlet and upstream to the fuel filter inlet.
FUEL SHUT-OFF
The Electronic Control Box controls the fuel solenoidvalve (3 Way Solenoid Valve) for positive fuelshut-off.The valve is controlled open during the start sequenceand closed during the stop sequence.Fuel is returned between the low pressure pump outletand the fuel filter inlet.
FLOW DIVIDER
The Flow Divider and Drain Valve (FDDVA) divides thefuel between the pilot and main injectors.During the initial start sequence, only the pilotinjectors are supplied.
TMUAPAF01-T01 LEVEL 3
EFFECTIVITY 49-32-00 Page 2Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 52EFFECTIVITYALL
TMUAPAF01-P01 LEVEL 3
FUEL SYSTEM DESCRIPTION OPERATION
EFFECTIVITY 49-32-00 Page 3Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 53EFFECTIVITYALL
FUEL SYSTEM DESCRIPTION OPERATION
FUEL DISTRIBUTION
Fuel distribution is assumed by 3 pilot and 6 mainfuel injectors.When APU start is selected, the pilot injector valveopens when fuel pressure reaches 20 psi.During normal running the two valves are in the openposition and the fuel is allowed to supply bothinjector types.
FUEL DRAIN
The fuel drain and vent valve assembly is installedin the APU compartment at the fuel inlet connectionto the FCU (drain of APU fuel feed line/bled of airfor maintenance).In the Flow Divider and Drain Valve Assembly (FDDVA)and during shutdown, as the fuel pressure decreases,the two injector valves close. The fuel remaining inthe pilot injector is purged to the exhaust bycombustion chamber pressure.An FCU drain line purges the pump shaft seal.
CONTROL
The Electronic Control Box controls the fuel systemusing several parameters.During on speed operation, the ECB uses APU speed,Exhaust Gas Temperature and aircraft demand signals.During start, it uses speed, EGT, air inlet pressureand temperature probes (P1 and T1).The Electronic Control Box acts on the fuel meteringvalve and fuel shut-off 3 way solenoid valve.
MONITORING
Contamination of the fuel system is monitored by thedifferential pressure indicator which sends a signalto the ECB.
TMUAPAF01-T01 LEVEL 3
EFFECTIVITY 49-32-00 Page 4Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 54EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAF01 LEVEL 3
EFFECTIVITY 49-32-00 Page 5Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 55EFFECTIVITYALL
SELF EXAMINATION
The Electronic Control box acts on:A - The fuel metering valve and the 3 way
solenoid valve ?B - The fuel metering valve and the pressure
regulator ?
When APU start is selected:A - The pilot injector valve opens ?B - The main injector valve opens ?C - Both valve types open ?
TMUAPAF01 LEVEL 3
EFFECTIVITY 49-32-00 Page 6Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 56EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-90-00 OIL SYSTEM DESCRIPTION OPERATION
StorageSupplyScavengeVentingControlProtectionMonitoringSelf Examination
TMUAPAO01 LEVEL 3
EFFECTIVITY 49-90-00 Page 1Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 57EFFECTIVITYALL
OIL SYSTEM DESCRIPTION
STORAGE
The sump of the APU accessory gearbox is the oilreservoir. The accessory gearbox sump contains 5.2 l (1.4 US gal)of oil.On the left side of the gearbox is located a gravityfill port with a scupper to drain spilled oil.The gearbox has :
- a fill tube for gravity filling,- an overflow drain,- a pressure fill connector,- a sight glass.
SUPPLY
The oil is drawn from the sump and pressurized by avane type pressure pump. If the pump pressure isexcessive, a pressure relief valve opens and releasesoil back to the inlet gearbox.Regulated oil passes through a cooler and a disposablefilter.The oil is then directed to the cooling fan splines,the APU spline shaft, the APU supporting bearings (Rearand front), the gearbox pinions and the electricalgenerator (AC generator and Generator spline shaft).
SCAVENGE
Oil from the electrical generator and APU rear bearingis returned to the sump by two scavenge pumps.The oil from the AC generator returns to the sumpthrough a vane type scavenge pump and a filter.
The oil from the APU rear bearing returns to the sumpthrough a gerotor scavenge pump.Oil from the gearbox pinions and the APU front bearingis scavenged by gravity.
VENTING
The air oil mist from the rear bearing is returned tothe gearbox housing through an external pipe.An air/oil separator removes the oil particules fromthe gearbox air.This oil free air is discharged in the APU exhaust.
CONTROL
The only component of the oil system controlled by theElectronic Control Box (ECB) is the de-oiling valve.The de-oiling solenoid valve is electricaly controlledopen during APU start to ensure cold start conditions,to reduce the load on the pressure pump, and duringAPU shut-down to prevent coking of the oil remainingin the bearing chambers.
PROTECTION
The Electronic Control Box protects the APU in caseof oil system malfunction. The ECB monitors oilpressure and oil temperature.If one of the oil parameters is out of range, theElectronic Control Box initiates an automatic APU shutdown without time delay.
- Gearbox high oil temp threshold : 135°C- AC generator high oil temp : 180°C- Oil low pressure : 35PSIT
MUAPAO01-T01 LEVEL 3
EFFECTIVITY 49-90-00 Page 2Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 58EFFECTIVITYALL
OIL SYSTEM DESCRIPTIONTMUAPAO01-P01 LEVEL 3
EFFECTIVITY 49-90-00 Page 3Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 59EFFECTIVITYALL
OIL SYSTEM DESCRIPTION
MONITORING
The oil system is monitored to increase the APU life.Lube and scavenge filters are equipped with visualclogging indicators.The oil sump is equipped with a low level sensor todisplay maintenance information in the cockpit. Whenthe level is at the "ADD" mark (4L/1USG) the APU mustbe able to continue running for at least 60 hours.A magetic drain plug, immersed in the APU oil, enablesthe oil drainage from the sump and attracts ferrousmetal particules.Two delta P switches (one for the scavenge filter anda second for the pressure filter) inform the ElectronicControl Box about a clogging situation (Class 2 faultmessage).
TMUAPAO01-T01 LEVEL 3
EFFECTIVITY 49-90-00 Page 4Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 60EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAO01 LEVEL 3
EFFECTIVITY 49-90-00 Page 5Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 61EFFECTIVITYALL
SELF EXAMINATION
What is the only component of the oil system controlledby the Electronic Control Box ?
A - The De-oiling solenoid valve.B - The low level sensor.C - The Low Oil Pressure.
How do you check the oil quantity ?A - On the ECAM OIL page, or on a sight
glass on the oil cooler, or by CFDSinterrogation.
B - On the ECAM APU page, or on a sightglass on the accessory gearbox, or byCFDS interrogation.
C - Only by CFDS interrogation and on theECAM ENGINE/WARNING page.
TMUAPAO01 LEVEL 3
EFFECTIVITY 49-90-00 Page 6Sep 30/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 62EFFECTIVITYALL
49 - APU
49-51-00 AIR SYSTEM DESCRIPTION OPERATION
CONTENTS:Bleed SupplyBleed ControlSurge ProtectionOil CoolingCompartment CoolingGearbox PressurizationOil VentControlMonitoringSelf Examination
TMUAPAA01 LEVEL 3
EFFECTIVITY 49-51-00 Page 1Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 63EFFECTIVITYALL
AIR SYSTEM DESCRIPTION OPERATION
BLEED SUPPLY
Bleed air supply to the aircraft pneumatic system iscontrolled by a bleed Control valve (deliveryfunction).The fuel operated bleed Control valve is a divertervalve (either to the aircraft system or the APUexhaust).
BLEED CONTROL
The amount of air required by the pneumatic system iscontrolled by the load compressor Inlet Guide Vanes(IGV).The Inlet Guide Vanes are moved by a fuel poweredactuator.
SURGE PROTECTION
Load compressor surge protection is also ensured bythe Bleed Control valve which discharges the excessof air in the exhaust (surge function).
OIL COOLING
A gearbox driven fan draws filtered air from the inletplenum and forces it to pass through the oil cooler.After leaving the oil cooler, the air is dischargedoverboard.The cooling fan incorporates a Permanent MagnetGenerator (PMG) which provides an emergency directcurrent supply to the Electronic Control Box, shouldthe main supply fail.
COMPARTMENT COOLING
Air supplied by the fan (driven by one of the gearsof the gearbox) is also used for APU compartmentcooling.A pneumatic compartment cooling valve enables air tobe blown through a smaller duct.Natural convection ventilates the APU compartment whenthe APU is not in operation.
GEARBOX PRESSURIZATION
Pressurized air enters the gearbox during operationfrom the front bearing seal buffering system (air frompower section compressor).
OIL VENT
The gearbox is vented to the APU exhaust. The air isbled after an air/oil separator action.
TMUAPAA01-T01 LEVEL 3
EFFECTIVITY 49-51-00 Page 2Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 64EFFECTIVITYALL
AIR SYSTEM DESCRIPTION OPERATIONTMUAPAA01-P01 LEVEL 3
EFFECTIVITY 49-51-00 Page 3Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 65EFFECTIVITYALL
AIR SYSTEM DESCRIPTION OPERATION
CONTROL
The Electronic Control Box controls the air systemusing several parameters:
- APU inlet pressure and temperature sensor andLoad Compressor Discharge Temperature sensor
- load compressor discharge pressure sensors(total and differential pressures)
- command and feed back signals from the actuatorand the valves.
Monitoring
To help maintenance and troubleshooting, the bleedload valve is equipped with visual position indicators(Load or Surge indication).The Load Compressor Discharge Temperature sensor(LCDT) is used to calculate the bleed air flow.
TMUAPAA01-T01 LEVEL 3
EFFECTIVITY 49-51-00 Page 4Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 66EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAA01 LEVEL 3
EFFECTIVITY 49-51-00 Page 5Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 67EFFECTIVITYALL
SELF EXAMINATION
Which component regulates the airflow to thepneumatic system ?
A - The bleed load valve.B - The Inlet Guide Vanes.
Which components have a visual position indicator ?A - Bleed load valve and IGV actuator.B - IGV actuator.C - Bleed load valve.
TMUAPAA01 LEVEL 3
EFFECTIVITY 49-51-00 Page 6Sep 31/99
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 68EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-60-00 APU SYSTEM MANAGEMENT
CONTENTS:GeneralPower upWatch and Start preparation stateStarting stateSteady stateCooldown stateNormal Shutdown Protective ShutdownEmergency ShutdownSelf Examination
TMUAPAC01 LEVEL 3
EFFECTIVITY 49-60-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 69EFFECTIVITYALL
APU SYSTEM MANAGEMENT
GENERAL
The APU system management and control keeps the APUrotation speed constant to obtain a constant ACgenerator frequency output, protects the power unitfrom over temperature, avoids load compressor surge,controls safe APU start and eases the APU maintenance.The APU management system controls the followingsequences:
- power state- watch state- starting state- steady run state- cooldown state- shutdown state
POWER UP STATE
When the APU Master Switch is set to ON, The APU fuelLow Pressure shutoff valve opens and the APU fuel pumplogic is energized.The ECB controls the opening of the air intake flapand initiates a Power Up test:
- test of OBRM, ROM checksum, RAM read/write- test of speed injection, oil level,discreteand analog outputs
WATCH AND START PREPARATION STATE
After completion of the POWER UP state, the ECBautomatically enters the WATCH state.Upon receipt of the start command, provided that thereare no prohibitive conditions and rotation speed is
less than or equal to 7% , the ECB enters the STARTPREPARATION state.
STARTING STATE
START P/B pressed + 100 mSecsWhen the START push-button has been pressed in, theECB initiates the start sequence. The receipt of astop signal at any time during the starting state leadsto a shutdown without any cooldown.The main electrical stage selected by the ECB is:
- Backup start contactor supply
BACKUP START CONTACTOR SUPPLIED +1,5 SECThe main electrical stages selected by the ECB are:
- gearbox de-oiling valve- ignition exciter control- main start contactor supply
ROTATION SPEED N > 3%The main electrical stages selected by the ECB are:
- 3 way solenoid valve for the HP fuel ON/OFFfunction,
- fuel servovalve for the fuel metering function.
ROTATION SPEED N > 5%During starting fuel flow is controlled under thefollowing programs:
- begin manifold fill algorithm- open loop fuel schedule
TMUAPAC01-T01 LEVEL 3
EFFECTIVITY 49-60-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 70EFFECTIVITYALL
TMUAPAC01-P01 LEVEL 3
APU SYSTEM MANAGEMENT - GENERAL
EFFECTIVITY 49-60-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 71EFFECTIVITYALL
APU SYSTEM MANAGEMENT
∆ EGT > 10°C- initiate acceleration control to 100% N
ROTATION SPEED N > 55%The main electrical stages selected by the ECB are:
- ignition exciter de energized- gearbox de-oiling valve de-energized- main start contactor de-energized
ROTATION SPEED N > 55% + 5 SECSbackup start contactor is de energized
ROTATION SPEED N > 95%The main electrical stages selected by the ECB are:
- surge control loop activation- APU AVAILable signal activation- start in progress output de-activation- steady state speed control loop activation- enter run state
STEADY STATE
SPEED CONTROLThis function keeps the rotation speed of the APUrotating assembly constant, whatever the load applied.This is achieved by metering the fuel flow, whichvaries with the air inlet pressure and temperature.
LOAD COMPRESSOR SURGE CONTROLThis function avoids compressor surge.
This is achieved by controlling and metering theposition of the Bleed Control Valve, according to theinlet and discharge pressure signals of the loadcompressor (∆P/P ratio).If ECB detects a surge condition, the Bleed ControlValve is positioned to discharge air to exhaust.
Note 1: In case of failure, the Bleed Control Valveis fully open to discharge.
Note 2: In case of reverse flow operation, the APU isautomatically shutdown by the ECB.
EGT CONTROLThis function avoids APU overtemperature bycontrolling the Inlet Guide Vane (IGV) position.Thus, the pneumatic load is first reduced to give thepriority to the electrical load.This is achieved by metering the position of the IGVas function of EGT and the operation mode Main EngineStart or Environmental Control System.
Note 1: In case of IGV control failure, the IGVs areclosed.
Note 2: In case of high EGT, the IGVs are closed.
TMUAPAC01-T02 LEVEL 3
EFFECTIVITY 49-60-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 72EFFECTIVITYALL
TMUAPAC01-P02 LEVEL 3
APU SYSTEM MANAGEMENT
EFFECTIVITY 49-60-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 73EFFECTIVITYALL
APU SYSTEM MANAGEMENT
COOLDOWN STATE
At stop command MASTER SW Off, all loads are removed(IGV closed, Bleed Control Valve to discharge, ACgenerator excitation cut out)then the engine goes intoa 120 second cooldown cycle.This function runs the APU at a low stabilizedtemperature before normal shutdown.
NORMAL SHUTDOWN
An APU normal shutdown is initiated when the MASTERSW pushbutton is released out.If the APU bleed air is not selected, the APU shutsdown immediately.The normal shutdown signal stops the fuel supply, Thiscauses the APU to decelerate. The AVAIL indicationgoes off and the AC generator de-energizes.When the speed is less than 90 %, the gearbox de-oilsolenoid valve opens.When the speed is less than 7% RPM, the air intakeflap is controlled to fully closed.
PROTECTIVE SHUTDOWN
When the ECB is powered, it controls the APU startingand running phases. If an abnormal parameter isdetected, it initiates an immediate shutdown withouttime delay, even if APU bleed air system is used.
ECB PROTECTIVE SHUTDOWN PARAMETERS:- OVERSPEED- OVERTEMPERATURE- LOW OIL PRESSURE- HIGH OIL TEMPERATURE- START PERIOD TIMER- SENSOR FAILURE- AIR INTAKE FLAP- NO FLAME- REVERSE FLOW- NO ACCELERATION- LOSS OF DC POWER - ECB FAILURE - GENERATOR HIGH OIL TEMPERATURE - LOSS OF SPEED SENSING - IGV SHUTDOWN
EMERGENCY SHUTDOWN
The ECB initiates an Emergency shutdown when eitherthe APU FIRE pushbutton (located in the cockpit) isreleased out or when the APU SHUT OFF pushbutton(located on external power receptacle panel) ispressed.The ECB initiates an automatic Emergency shutdown whenan APU FIRE is detected on ground.The APU shuts down immediately without time delay,even if the APU bleed air system is used.
TMUAPAC01-T03 LEVEL 3
EFFECTIVITY 49-60-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 74EFFECTIVITYALL
SELF EXAMINATION
When does the APU air intake flap open?A - As soon as the APU operates under air
load.B - As soon as ignition begins.C - As soon as MASTER SW pushbutton is set
to ON.
APU is running and APU bleed air system is in use.What happens if APU MASTER SW pushbutton isreleased out?
A - The APU shuts down after a cooling cyclehas been completed.
B - The APU shuts down immediately.C - The APU shuts down after the closure of
fuel LP shut off valve.
The starter motor assists the APU up to which speed?A - 55 % RPM.B - 40 % RPM.C - 95 % RPM.
TMUAPAC01 LEVEL 3
EFFECTIVITY 49-60-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 75EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAC01 LEVEL 3
EFFECTIVITY 49-60-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 76EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-70-00 APU WARNINGS
CONTENTS:Automatic Shut DownEmergency Shut Down
TMUAPA601 LEVEL 3
EFFECTIVITY 49-70-00 Page 1Nov 30/97
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 77EFFECTIVITYALL
APU WARNINGS
AUTO SHUT DOWN
If an AUTO SHUT DOWN occurs, the aural warning sounds,the MASTER CAUT and the MASTER SW FAULT light come on.The ECAM warning page is activated and the APU ECAMpage is called automatically.AUTO SHUT DOWN when :
- Overspeed- EGT Overtemperature- Low oil pressure- High oil temperature- Start period timer- Sensor failure EGT or Low Oil Pressure switch- Air intake not open- Underspeed- No flame- Reverse flow- No acceleration- DC power lost- ECB failure- Generator High Oil Temperature- Loss of speed sensing
EMER SHUT DOWN
If an EMER SHUT DOWN occurs, the aural warning sounds,the MASTER CAUT and the MASTER SW FAULT light come on.The ECAM warning page is activated and the APU ECAMpage is called automatically.An EMER SHUT DOWN occurs when:
- The APU shut off pushbutton is pressed on theexternal power control panel
- The APU FIRE pushbutton is released out on theoverhead panel
- The automatic fire extinguishing logic istriggered on ground.
TMUAPA601-T01 LEVEL 3
EFFECTIVITY 49-70-00 Page 2Nov 30/97
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 78EFFECTIVITYALL
APU WARNINGS - AUTOMATIC SHUT DOWN & EMERGENCY SHUT DOWNTMUAPA601-P01 LEVEL 3
EFFECTIVITY 49-70-00 Page 3Nov 30/97
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 79EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPA601 LEVEL 3
EFFECTIVITY 49-70-00 Page 4Nov 30/97
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 80EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-60-00 ECB INTERFACES
CONTENTS:Power SupplyMaster Switch PushbuttonAir Intake FlapStart PushbuttonBack Up and Main Start ContactorsEmergency StopLGCIU 1APU Fuel Feed SystemEIUsBMCsTSO/JARZone Controller A320/321Generator Oil Temperature SensorSDACsCFDS
TMUAPA101 LEVEL 3
EFFECTIVITY 49-60-00 Page 1Jul 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 81EFFECTIVITYALL
ECB INTERFACES
POWER SUPPLY
The Electronic Control Box is electrically supplied,through the APU MAIN control relay, by at least oneof the aircraft batteries, the aircraft DC networkand/or from the 28 VDC Permanent Magnet Generator.
MASTER SWITCH PUSHBUTTON
The APU MASTER SWITCH sends a discrete supply or stopsignal to the ECB.The Electronic Control Box sends a discrete signal tothe FAULT light when an automatic shutdown occurs ora Power Up Test fails.
AIR INTAKE FLAP
The ECB receives an air intake flap open or closedposition signal and sends a power output for openingor closing the air intake flap.
START PUSHBUTTON
A discrete input signal from the START pushbuttoninitiates the starting sequences.The ECB sends a discrete signal to the ON light duringAPU start sequence.A discrete output signal to the aircraft energizes theAVAIL light in the START pushbutton when the APU speedis above 95 %.
BACK UP AND MAIN START CONTACTORS
The ECB receives a discrete input from the Main StartContactor and sends discrete outputs to the Back Upand the Main Start Contactors.
EMERGENCY STOP
A discrete input signal from the aircraft initiatesthe APU shutdown logic after the ECB has received thissignal.
LGCIU 1
The ECB receives the flight/ground discrete inputsignal from the Landing Gear Control and InterfaceUnit 1 (LGCIU 1).This signal is used for automatic shutdown inhibitionlogic and for failed sensor logic.
APU FUEL FEED SYSTEM
The ECB receives a discrete signal from the APU LowFuel Pressure Switch.It sends a discrete signal to theAPU Fuel LP Shut OffValve.
TMUAPA101-T01 LEVEL 3
EFFECTIVITY 49-60-00 Page 2Jul 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 82EFFECTIVITYALL
TMUAPA101-P01 LEVEL 3
ECB INTERFACES
EFFECTIVITY 49-60-00 Page 3Jul 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 83EFFECTIVITYALL
ECB INTERFACES
EIUs
During engine starts, the ECB receives a Main EngineStart signal from Engine Interface Units 1 or 2.This signal causes the ECB to position the Inlet GuideVanes to fully open and the Bleed Control Valve tomodulate in delivery position.
BMCs
When the APU bleed pushbutton is set to ON, BMC 1 or2 sends a discrete input to the ECB which controlsthe opening of the APU Bleed Control Valve.
TSO/JAR
The ECB receives a discrete input from the aircraftsignature PIN programmingThis open or ground signal determines whether the ECBfollows the Technical Standard Order (TSO) or the JointAirworthiness Requirements (JAR).
ZONE CONTROLLER
The ECB receives, via an ARINC 429 bus, an input fromthe Zone Controller to control the IGV and the BleedControl Valve position according to the demand.The ECB sends a discrete output to the Zone Controllerto signal that the APU bleed control valve is indelivery position.
A320/321
The ECB receives a discrete input from the aircraftsignature PIN programmingThis identification PIN allows the ECB to identifyA321 applications for functional differences fromthose of an A320.
GENERATOR OIL TEMPERATURE SENSOR
The ECB receives an analog input from this sensor whichis an aircraft supplied component mounted on the ACgenerator.
SDACs
The ECB sends to SDACs 1 and 2, via ARINC 429 Databuses, the indications to be displayed on the ECAM APUpage and shutdown information to trigger thecorresponding warnings.
CFDS
The ECB is a type 1 computer and is connected to theCentralized Fault Display System via ARINC 429 Databuses.
TMUAPA101-T02 LEVEL 3
EFFECTIVITY 49-60-00 Page 4Jul 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 84EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-30-00 APU FUEL SYSTEM COMPONENTS
CONTENTS:Fuel Control Unit LP Filter Servo Valve Fuel Nozzles Fuel Divider and Drain Valve Assembly (FDDVA)Case Drain Valve
TMUAPAV02 LEVEL 3
EFFECTIVITY 49-30-00 Page 1Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 85EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
FUEL CONTROL UNIT
IDENTIFICATIONFIN: 4005 KM2
LOCATIONZONE: 315
COMPONENT DESCRIPTION
The FCU is mounted by a V band clamp on the front faceof the gearbox.
The control and metering section includes :- a constant delta P valve which controls thedifferential pressure accross the servovalve,
- a 3 way solenoid valve.
The pump section includes :- a low pressure pump,- a low pressure filter,- a high pressure pump provided with apressure relief valve.
TMUAPAV02-T01 LEVEL 3
EFFECTIVITY 49-30-00 Page 2Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 86EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - FUEL CONTROL UNITTMUAPAV02-P01 LEVEL 3
EFFECTIVITY 49-30-00 Page 3Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 87EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
FUEL CONTROL UNIT - LP FILTER
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe inlet section includes :
- an inlet fuel filter.- a filter bypass valve.- an inlet filter differential pressureindicator.
TMUAPAV02-T02 LEVEL 3
EFFECTIVITY 49-30-00 Page 4Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 88EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - LP FILTERTMUAPAV02-P02 LEVEL 3
EFFECTIVITY 49-30-00 Page 5Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 89EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
FUEL CONTROL UNIT - SERVO VALVE
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe control and metering section includes :
- a Servo Valve.
TMUAPAV02-T03 LEVEL 3
EFFECTIVITY 49-30-00 Page 6Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 90EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - SERVO VALVETMUAPAV02-P03 LEVEL 3
EFFECTIVITY 49-30-00 Page 7Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 91EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
FUEL NOZZLES
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe 3 pilot fuel injectors spray the fuel into thecombustion chamber to permit starting.They also remain in operation during normal runningto prevent coking.The 6 main injectors spray the fuel into the combustionchamber.
TMUAPAV02-T04 LEVEL 3
EFFECTIVITY 49-30-00 Page 8Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 92EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - FUEL NOZZLESTMUAPAV02-P04 LEVEL 3
EFFECTIVITY 49-30-00 Page 9Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 93EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
FUEL DIVIDER AND DRAIN VALVE ASSEMBLY (FDDVA)
IDENTIFICATIONFIN: 4005 KM1
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe Fuel Divider and Drain Valve Assembly contains :
- a fuel filter element.- a pilot injector and purge valve.- a secondary drain valve.- a main injector valve.
TMUAPAV02-T05 LEVEL 3
EFFECTIVITY 49-30-00 Page 10Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 94EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - FUEL DIVIDER AND DRAIN VALVE ASSEMBLY (FDDVA)TMUAPAV02-P05 LEVEL 3
EFFECTIVITY 49-30-00 Page 11Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 95EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS
CASE DRAIN VALVE
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONA combustion chamber case drain valve is provided todrain fuel that may accumulate in the combustor andthe plenum following an unsuccessful light up.
TMUAPAV02-T06 LEVEL 3
EFFECTIVITY 49-30-00 Page 12Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 96EFFECTIVITYALL
APU FUEL SYSTEM COMPONENTS - CASE DRAIN VALVETMUAPAV02-P06 LEVEL 3
EFFECTIVITY 49-30-00 Page 13Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 97EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAV02 LEVEL 3
EFFECTIVITY 49-30-00 Page 14Sep 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 98EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-90-00 APU OIL SYSTEM COMPONENTS
CONTENTSLubrication UnitDrain PlugOil Level SensorDe-oil ValveOil Cooler AssemblyLow Oil Pressure switchHigh Oil Temperature switchOil FiltersOil Ports
TMUAPAT01 LEVEL 3
EFFECTIVITY 49-90-00 Page 1Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 99EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
LUBRICATION UNIT
IDENTIFICATIONFIN: 4005 KM6
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe oil sump assembly is formed by the lower part ofthe gearbox.One pressure pump and two scavenge pumps are drivenby the gearbox.
TMUAPAT01-T01 LEVEL 3
EFFECTIVITY 49-90-00 Page 2Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 100EFFECTIVITYALL
TMUAPAT01-P01 LEVEL 3
APU OIL SYSTEM COMPONENTS - LUBRICATION UNIT
EFFECTIVITY 49-90-00 Page 3Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 101EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
DRAIN PLUG
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe drain plug contains a chip detector.When the chip detector is removed, a check valveprevents oil loss.
TMUAPAT01-T02 LEVEL 3
EFFECTIVITY 49-90-00 Page 4Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 102EFFECTIVITYALL
TMUAPAT01-P02 LEVEL 3
APU OIL SYSTEM COMPONENTS - DRAIN PLUG
EFFECTIVITY 49-90-00 Page 5Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 103EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
OIL LEVEL SENSOR
IDENTIFICATIONFIN: 119 KD
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe oil level sensor is a Resistive Temperature Device.The resistance varies with the oil level and modifiesthe sensor output voltage checked by the ECB.
TMUAPAT01-T03 LEVEL 3
EFFECTIVITY 49-90-00 Page 6Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 104EFFECTIVITYALL
TMUAPAT01-P03 LEVEL 3
APU OIL SYSTEM COMPONENTS - OIL LEVEL SENSOR
EFFECTIVITY 49-90-00 Page 7Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 105EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
DE-OIL VALVE
IDENTIFICATIONFIN: 117 KD
LOCATIONZONE: 315
COMPONENT DESCRITIONThe de-oil valve permits air to enter the suction sideof the lubrification pump to reduce the starter loadin the following conditions :
- If the oil sump temperature is below -6.7°C(20°F) during the start sequence between 0%and 60% APU speed.
- When the APU speed is between 95% and 7% ateach shutdown.
- When the altitude is more than 30,000 ft ateach start.
TMUAPAT01-T04 LEVEL 3
EFFECTIVITY 49-90-00 Page 8Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 106EFFECTIVITYALL
TMUAPAT01-P04 LEVEL 3
APU OIL SYSTEM COMPONENTS - DE-OIL VALVE
EFFECTIVITY 49-90-00 Page 9Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 107EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
OIL COOLER ASSEMBLY
IDENTIFICATIONFIN: 4005 KM5
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe oil cooler includes:
- An air cooler housing which consists of anintegrally brazed aluminium heat exchanger withaluminium face flanges and stainless steel backup flanges
- A check valve and a by pass valve- A drain plug.
TMUAPAT01-T05 LEVEL 3
EFFECTIVITY 49-90-00 Page 10Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 108EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS - OIL COOLERTMUAPAT01-P05 LEVEL 3
EFFECTIVITY 49-90-00 Page 11Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 109EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
LOW OIL PRESSURE SWITCH
IDENTIFICATIONFIN: 121 KD
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe Low Oil Pressure switch contact opens to signallow oil pressure.
TMUAPAT01-T06 LEVEL 3
EFFECTIVITY 49-90-00 Page 12Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 110EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS - LOW OIL PRESSURE TMUAPAT01-P06 LEVEL 3
EFFECTIVITY 49-90-00 Page 13Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 111EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
HIGH OIL TEMPERATURE SWITCH
IDENTIFICATIONFIN:120 KD
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe High Oil Temperature sensor is a resistivetemperature device.The resistance varies with the oil temperature andmodifies the sensor output voltage.
TMUAPAT01-T07 LEVEL 3
EFFECTIVITY 49-90-00 Page 14Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 112EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS - HIGH OIL TEMPERATURE SWITCHTMUAPAT01-P07 LEVEL 3
EFFECTIVITY 49-90-00 Page 15Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 113EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
OIL FILTERS
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENTS DESCRIPTIONThe 20 microns filter elements for the generator oilscavenge filter and the lubrication filter areidentical.The impending blockage indicator pops up for a ∆Phigher than 30 to 35 PSI.A bypass valve opens for a ∆P higher than 30 to 60PSI.
TMUAPAT01-T08 LEVEL 3
EFFECTIVITY 49-90-00 Page 16Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 114EFFECTIVITYALL
TMUAPAT01-P08 LEVEL 3
APU OIL SYSTEM COMPONENTS - OIL FILTERS
EFFECTIVITY 49-90-00 Page 17Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 115EFFECTIVITYALL
APU OIL SYSTEM COMPONENTS
OIL PORTS
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENTS DESCRIPTIONWhen using the pressure fill port, do not overfill theAPU.
TMUAPAT01-T09 LEVEL 3
EFFECTIVITY 49-90-00 Page 18Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 116EFFECTIVITYALL
TMUAPAT01-P09 LEVEL 3
APU OIL SYSTEM COMPONENTS - OIL PORTS
EFFECTIVITY 49-90-00 Page 19Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 117EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAT01 LEVEL 3
EFFECTIVITY 49-90-00 Page 20Jun 30/00
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 118EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-50-00 APU AIR SYSTEM COMPONENTS
CONTENTSBleed Control ValveInlet Guide VaneLoad Compressor Discharge Temperature SensorLoad Compressor Discharge Pressure SensorsLoad Compressor Inlet Pressure And Temperature SensorCooling Fan
TMUAPAW01 LEVEL 3
EFFECTIVITY 49-50-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 119EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
BLEED CONTROL VALVE
IDENTIFICATIONFIN: 110 KD
LOCATIONZONE: 316
COMPONENT DESCRIPTIONThe Bleed Control Valve is located on the right lowerpart of the APU at the scroll outlet.It delivers air to the aircraft while avoiding loadcompressor surge.The valve is selected from the APU BLEED pushbuttonswitch, and controlled by the ECB.
TMUAPAW01-T01 LEVEL 3
EFFECTIVITY 49-50-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 120EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS - BLEED CONTROL VALVETMUAPAW01-P01 LEVEL 3
EFFECTIVITY 49-50-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 121EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
INLET GUIDE VANE SYSTEM
IDENTIFICATIONFIN: 111 KD
LOCATIONZONE: 316
COMPONENT DESCRIPTIONThe Inlet Guide Vanes and their control mechanism arelocated at the load compressor air inlet.The servo valve and actuator form an assembly locatedon the right upper part of the APU on the loadcompressor casing.
TMUAPAW01-T02 LEVEL 3
EFFECTIVITY 49-50-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 122EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS - INLET GUIDE VANETMUAPAW01-P02 LEVEL 3
EFFECTIVITY 49-50-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 123EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
LOAD COMPRESSOR DISCHARGE TEMPERATURE SENSOR (LCDT)
IDENTIFICATIONFIN: 102 KD
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe LCDT is located on the bleed valve inlet duct.The LCDT provides an input signal to the ECB forindication, it’s a resistance temperature device.
TMUAPAW01-T03 LEVEL 3
EFFECTIVITY 49-50-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 124EFFECTIVITYALL
TMUAPAW01-P03 LEVEL 3
APU AIR SYSTEM COMPONENTS - LOAD COMPRESSOR DISCHARGE TEMPERATURE SENSOR (LCDT)
EFFECTIVITY 49-50-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 125EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
LOAD COMPRESSOR DISCHARGE PRESSURE SENSORS
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe pressure sensors are assembled together in oneunit which is located on the front of the air intakeplenum.They are made of a bridge of 4 resistors.
TMUAPAW01-T04 LEVEL 3
EFFECTIVITY 49-50-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 126EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS - LOAD COMPRESSOR DISCHARGE PRESSURE SENSORSTMUAPAW01-P04 LEVEL 3
EFFECTIVITY 49-50-00 Page 9Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 127EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
LOAD COMPRESSOR INLET PRESSURE AND TEMPERATURE SENSOR
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe sensor is located on the rear of the air intakeplenum.The pressure sensor is made of a bridge of 4 resistorsprinted on a flexible support, the temperature sensoris an adjustable resistor.
TMUAPAW01-T05 LEVEL 3
EFFECTIVITY 49-50-00 Page 10Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 128EFFECTIVITYALL
TMUAPAW01-P05 LEVEL 3
APU AIR SYSTEM COMPONENTS - LOAD COMPRESSOR INLET PRESSURE AND TEMPERATURE SENSOR
EFFECTIVITY 49-50-00 Page 11Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 129EFFECTIVITYALL
APU AIR SYSTEM COMPONENTS
COOLING FAN
IDENTIFICATIONFIN:
LOCATIONZONE: 315
COMPONENT DESCRIPTION
The cooling fan incorporates a generator which providesan emergency direct current to the Electronic ControlBox.The cooling fan is located at the gearbox front face.
TMUAPAW01-T06 LEVEL 3
EFFECTIVITY 49-50-00 Page 12Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 130EFFECTIVITYALL
TMUAPAW01-P06 LEVEL 3
APU AIR SYSTEM COMPONENTS - COOLING FAN
EFFECTIVITY 49-50-00 Page 13Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 131EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAW01 LEVEL 3
EFFECTIVITY 49-50-00 Page 14Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 132EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-00-00 MISCELLANEOUS APU SYSTEMCOMPONENTS
CONTENTS:Attach RodsStarter MotorSerial Number EncoderEGT SensorSpeed SensorElectronic Control BoxDrain TankIgnition Unit
TMUAPAS01 LEVEL 3
EFFECTIVITY 49-00-00 Page 1Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 133EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
ATTACH RODS
IDENTIFICATIONFIN: 4065/4075/4085 KM
LOCATIONZONE:315/316
COMPONENT DESCRIPTIONDuring APU removal and installation, use the threadprotectors to prevent damaging the bolts.
TMUAPAS01-T01 LEVEL 3
EFFECTIVITY 49-00-00 Page 2Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 134EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - ATTACH RODSTMUAPAS01-P01 LEVEL 3
EFFECTIVITY 49-00-00 Page 3Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 135EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
STARTER MOTOR
IDENTIFICATIONFIN: 4005 KM1
LOCATIONZONE: 315/316
COMPONENT DESCRIPTIONThe starter motor is a series wound DC electric motorwith 4 poles and 4 brushes.It is equipped with a visual and an electrical brushwear indicator.
TMUAPAS01-T02 LEVEL 3
EFFECTIVITY 49-00-00 Page 4Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 136EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENT - STARTER MOTORTMUAPAS01-P02 LEVEL 3
EFFECTIVITY 49-00-00 Page 5Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 137EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
SERIAL NUMBER ENCODER
IDENTIFICATIONFIN: 116 KD
LOCATIONZONE: 315
COMPONENT DESCRIPTIONThe engine identification module is made of resistorslocated on printed circuit board.The Electronic Control Box (ECB) automatically resetsthe cycles and hours to zero when it sees a change inAPU serial number.
TMUAPAS01-T03 LEVEL 3
EFFECTIVITY 49-00-00 Page 6Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 138EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - SERIAL NUMBER ENCODERTMUAPAS01-P03 LEVEL 3
EFFECTIVITY 49-00-00 Page 7Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 139EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
EGT SENSOR
IDENTIFICATIONFIN: P30, P31
LOCATIONZONE: 315/316
COMPONENT DESCRIPTIONThe thermocouples provide an electromotive force infunction of the temperature difference between the hotjunction in the exhaust gas stream and the coldjunction connected to the measuring device.The two EGT rakes (EGT sensors) are separatelyconnected and the ECB uses the higher value. In caseof failure of a rake, the ECB uses the remaining one.
TMUAPAS01-T04 LEVEL 3
EFFECTIVITY 49-00-00 Page 8Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 140EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - EGT SENSORTMUAPAS01-P04 LEVEL 3
EFFECTIVITY 49-00-00 Page 9Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 141EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
SPEED SENSOR
IDENTIFICATIONFIN: 113 KD, 112 KD
LOCATIONZONE: 315/316
COMPONENT DESCRIPTIONThe two independent magnetic speed sensors are locatedin front of a common target phonic wheel.
TMUAPAS01-T05 LEVEL 3
EFFECTIVITY 49-00-00 Page 10Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 142EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - SPEED SENSORTMUAPAS01-P05 LEVEL 3
EFFECTIVITY 49-00-00 Page 11Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 143EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
ELECTRONIC CONTROL BOX
IDENTIFICATIONFIN: 59 KD
LOCATIONZONE: 152
COMPONENT DESCRIPTIONThe Electronic Control Box (ECB) is a fully digitalelectronic controller that does the primary part ofthe APU system logic.It is located in the bulk cargo compartment, righthand side.
TMUAPAS01-T06 LEVEL 3
EFFECTIVITY 49-00-00 Page 12Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 144EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - ELECTRONIC CONTROL BOXTMUAPAS01-P06 LEVEL 3
EFFECTIVITY 49-00-00 Page 13Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 145EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
DRAIN TANK
IDENTIFICATIONFIN:
LOCATIONZONE: 316
COMPONENT DESCRIPTIONThe capacity of the drain tank is three shutdowns ofthe APU when the aircraft is on the ground.After three shutdowns, the contents will automaticallydrain when the drain system tank is full.In flight, due to suction effect, it is automaticallydrained.
TMUAPAS01-T07 LEVEL 3
EFFECTIVITY 49-00-00 Page 14Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 146EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - DRAIN TANKTMUAPAS01-P07 LEVEL 3
EFFECTIVITY 49-00-00 Page 15Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 147EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS
IGNITION UNIT
IDENTIFICATIONFIN: P10
LOCATIONZONE: 315/316
COMPONENT DESCRIPTIONThe ignition exciter is a sealed metal box assemblywith a mounting bracket on one side.Power is supplied to the ignition exciter through amultipin electrical connector, the two igniter cablesconnect the two connectors to the igniters.
TMUAPAS01-T08 LEVEL 3
EFFECTIVITY 49-00-00 Page 16Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 148EFFECTIVITYALL
MISCELLANEOUS APU SYSTEM COMPONENTS - IGNITION UNITTMUAPAS01-P08 LEVEL 3
EFFECTIVITY 49-00-00 Page 17Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 149EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPAS01 LEVEL 3
EFFECTIVITY 49-00-00 Page 18Aug 31/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 150EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-11-00 APU COMPARTMENT ACCESS DOOROPERATION
CONTENTS:Door OpeningDoor Closure
TMUAPUK01 LEVEL 3
EFFECTIVITY 49-11-00 Page 1Jun 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 151EFFECTIVITYALL
APU COMPARTMENT ACCESS DOOR OPERATION
DOOR OPENING
In the cockpit, open the APU circuit breakers.Position a work stand suitable to reach the aircraftunder the APU compartment.The APU doors are secured by a total of seven latches,five latches secure the left door and two latchessecure the right door.The left hand door must be opened first to gain accessto the latches for the right hand door.Start by releasing the rear latch.Next, the three latches connecting the doors togetherare undone.As each latch is undone, secure the latch hook on thelatch lever.Continue to release the remaining latches.When all latches have been released, pull the dooropen and secure with the door support strut.The strut is stowed at the forward end of the leftdoor.Release the strut pip-pin from the door, extend thetelescopic strut and secure to the aircraft using thepip-pin.Push the door open until the strut locks in the fullyextended position.This completes the opening of the left hand door.With the left hand door open, the two latches securingthe right hand door are now visible.The forward latch is released.Followed by the rear latch and the door is ready tobe opened.
Use the assist handle mounted on the air inlet ductand swing the door fully open.The door hold open mechanism incorporates acounterbalance spring that takes most of the doorweight.The door will lock automatically in the door openposition.No locking pins are necessary to secure the right handdoor in the open position.A red coloured pip-pin is provided to lock the doorhold open spring mechanism should it become necessaryto remove the door from the aircraft. In this eventthe red pip-pin should be removed from its stowage andinserted in the adjacent hole with a red surround. Toprevent injury, a placard advises against removal ofthe red coloured bolt when the access door is removed.This completes the APU door opening procedure.
CAUTION: In event of door removal you must secure theright access door hold-open device byinserting the locking pin in the locking hole.The pin is stowed next to this locking hole.
TMUAPUK01-T01 LEVEL 3
EFFECTIVITY 49-11-00 Page 2Jun 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 152EFFECTIVITYALL
APU COMPARTMENT ACCESS DOOR OPERATIONTMUAPUK01-P01 LEVEL 3
EFFECTIVITY 49-11-00 Page 3Jun 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 153EFFECTIVITYALL
APU COMPARTMENT ACCESS DOOR OPERATION
DOOR CLOSURE
To close the right hand door, apply a lifting forceto the door with one hand, and at the same time, tapthe orange coloured release handle marked "PUSH" in adownward, outward direction to release the overcentregeometric lock on the door hold open mechanism.Lift the door to the closed position, using the assisthandle on the air inlet duct.Secure the forward and rear latches on the right handdoor.The left door support strut must be stowed beforeclosing the left door.To release the lock on the left hand door supportstrut, pull down on the knurled collar. While holdingthe collar down, partially close the door.Hold the door with the left hand and with the righthand, release the door support strut pip-pin from theaircraft. Stow the support strut on the door. Closethe left door.Secure the forward latch.Ensure that the latch release lever is flush with thelatch.Secure the rear latch.Secure the three latches holding the left and rightdoors together. To secure these latches:
- Release the latch hook by pressing the latchrelease lever.
- Engage the latch hook in the locking bracket.- Close the latch lever. - Ensure that the latch release lever is flushwith the latch.
Repeat the closing procedure for the remaining latches.Carry out a final visual inspection to ensure that alllatches are secure. This completes the APU access doorclosing procedure. Finally, reset the APU circuitbreakers in the cockpit.
TMUAPUK01-T01 LEVEL 3
EFFECTIVITY 49-11-00 Page 4Jun 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 154EFFECTIVITYALL
49 - AUXILIARY POWER UNIT
49-12-00 APU REMOVAL AND INSTALLATION
CONTENTS:WarningFuel DrainElectrical Connectors 1Electrical Connectors 2PneumaticHoistingMountsSupport Frame
TMUAPUR01 LEVEL 3
EFFECTIVITY 49-12-00 Page 1Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 155EFFECTIVITYALL
APU REMOVAL AND INSTALLATION
WARNING
WARNING: Make sure that you have the correct firefighting equipment available.
WARNING: Do not touch the APU until it is sufficientlycool to prevent burns when you do themaintenance task.
WARNING: Lock the mechanism of access door 316 AR withthe pip pin when you open the access door.
WARNING: Depressurize green and yellow hydraulicsystems.
WARNING: Open, safety and tag the appropriate circuitbreakers.
NOTE: Before APU removal, on the CFDS, do the BITEtest of the APU and record the APU hours andcycles.
NOTE: After APU installation, bleed the APU fuel linebefore you start the APU (to prevent hot start).
TMUAPUR01-T01 LEVEL 3
EFFECTIVITY 49-12-00 Page 2Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 156EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPUR01 LEVEL 3
EFFECTIVITY 49-12-00 Page 3Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 157EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - FUEL DRAINTMUAPUR01-P01 LEVEL 3
EFFECTIVITY 49-12-00 Page 4Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 158EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - ELECTRICAL CONNECTORS 1TMUAPUR01-P02 LEVEL 3
EFFECTIVITY 49-12-00 Page 5Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 159EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - ELECTRICAL CONNECTORS 2TMUAPUR01-P03 LEVEL 3
EFFECTIVITY 49-12-00 Page 6Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 160EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - PNEUMATICTMUAPUR01-P04 LEVEL 3
EFFECTIVITY 49-12-00 Page 7Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 161EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - HOISTINGTMUAPUR01-P05 LEVEL 3
EFFECTIVITY 49-12-00 Page 8Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 162EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - MOUNTSTMUAPUR01-P06 LEVEL 3
EFFECTIVITY 49-12-00 Page 9Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 163EFFECTIVITYALL
APU REMOVAL AND INSTALLATION - SUPPORT FRAMETMUAPUR01-P07 LEVEL 3
EFFECTIVITY 49-12-00 Page 10Nov 30/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 164EFFECTIVITYALL
49 - APU
49-73-00 CFDS SPECIFIC PAGE PRESENTATION
CONTENTS:APU Data/oilPerformance SettingsShutdowns.
TMUAPWY06 LEVEL 3
EFFECTIVITY 49-73-00 Page 1Mar 31/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 165EFFECTIVITYALL
CFDS SPECIFIC PAGE PRESENTATION
APU DATA/OIL
To gain access to the SYSTEM REPORT/TEST APU MENU, theAPU MASTER SWITCH must be set to ON.The APU is a type 1 system. It is not available inCFDS back-up mode.The APU DATA/OIL page gives the :
- APU serial number- APU operating hours- APU cycles- APU oil level.
"OIL LEVEL:LOW" replaces"OIL LEVEL:OK" when the oilquantity decreases to 3.69 l (3.9 qt.).Each APU contains a serial number encoder whichprovides the information required for proper CFDSinterpretation, continuity of LRU fault history, hoursand cycles of the APU.When you replace an APU or a serial number encoder,the ECB resets the APU hours and cycles to zero. TheData Management Unit (DMU) of the Aircraft IntegratedData System (AIDS) also calculates the APU hours andcycles so that their records are not lost when an ECBis replaced.
PERFORMANCE SETTINGS
The APU Performance Settings page gives the settingsof:
- EGT trim- COOLDOWN time
Base maintenance staff cannot modify these settingswhich are programmed by adjusting the variouselectronic switches within the ECB (5 levelsavailable) following the aircraft operatingconditions.
SHUTDOWNS.
The APU SHUTDOWNS page gives the reason of the shutdown(OVERSPEED) and the related LRUs causing thefault(classed in descending probability order) .Refer to the TSM to trouble shoot the faulty componentwhich caused the shutdown.
TMUAPWY06-T01 LEVEL 3
EFFECTIVITY 49-73-00 Page 2Mar 31/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 166EFFECTIVITYALL
CFDS SPECIFIC PAGESTMUAPWY06-P01 LEVEL 3
EFFECTIVITY 49-73-00 Page 3Mar 31/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 167EFFECTIVITYALL
THIS PAGE INTENTIONALLY LEFT BLANK
TMUAPWY06 LEVEL 3
EFFECTIVITY 49-73-00 Page 4Mar 31/94
_A319/A320/A321 TECHNICAL TRAINING MANUAL 49 APU (APIC)MECHANICS / ELECTRICS & AVIONICS COURSE
UFD4200
Page 168EFFECTIVITYALL
top related