auma electric actuators. 2 auma scope of supply actuators for valves requiring multi turn actuation:...

Post on 18-Dec-2015

403 Views

Category:

Documents

6 Downloads

Preview:

Click to see full reader

TRANSCRIPT

AUMA Electric Actuators

2

AUMA scope of supply

Actuators for valves requiring multi turn actuation:

Gate valves Sluice gates Globe valves Pinch valves

Actuators for valves requiring quarter turn actuation:

Butterfly valves Ball valves Plug valves

Actuators for valves requiring linear actuation:

Globe valves

3

AUMA provides a complete range of electric actuators

Multi turn output up to 60,000 ft lb torque / 900,000 lb thrust

Quarter turn output up to 498,000 ft lb torque

Linear output up to 48,825 lb thrust

4

AUMA offers three actuator control configurations

Conventional actuator• Limit switches• Torque switchesConventional controls• AUMA Matic (AM)

Non-intrusive actuator• MWG – encoders sense position & torqueMicroprocessor- based controls• AUMATIC (AC)

Conventional actuator• Limit switches• Torque switchesWithout controls – AUMA NORM

5

A solution for any environmental / ambient application

Watertight applications• NEMA 4 / 4X• IP67

Explosionproof applications• FM• CSA• ATEX• Other global approvals

High & low ambient temperature• As high as +250º F (+120º C)• As low as -76º F (-60º C)

Submersible applications• NEMA 6 • IP68

6

Model SA multiturn actuator

Drive - motor (or hand wheel) drives a worm/worm wheel gearset which turns a hollow output drive shaft.

7

Model SA multiturn actuator

• 11 sizes

• output torque from 7 to 23,600 ft lbs

• thrust acceptance up to 450,000 lbs

• speed from 4.8 up to 216 rpm (at 60 Hz, in 12 increments - speed selections reduced for larger actuators)

SA07.2 – SA16.2 SA25.1 – SA48.1

8

SA Multiturn Actuator coupled with GK or GHT Multiturn Gearbox

SA actuator / GK gearbox Up to 11,900 ft lb torque Up to 309,000 lb thrust

SA actuator / GHT gearbox Up to 60,000 ft lb torque Up to 900,000 lb thrust

9

Plug & socket electrical connection

• Screw / compression connection (no special tools required)

• Field wiring can be performed prior to actuator / valve installation

• Once wired, field wiring can be unplugged

• Can be utilized as a disconnect or supplied with a disconnect switch

• Safe terminals

• Optional ring-tongue terminals

10

Easily to set-up / commission

Easily settable position limit switches• Just a few turns of a slotted shaft• No declutch shaft

Easy torque switch adjustment

Test knobs to check limit & torque switches

11

User friendly design offers actuator configuration flexibility

SA actuators can be furnished as conventional or non-intrusive actuators

12

SA actuators can be furnished as ‘non-intrusive’ actuators

What is a non-intrusive actuator?

An actuator whose parameters can be set without gaining access to the inside of the unit.

13

Non-intrusive actuators - 3 ways to set parameters

1. Manipulate local controls2. Wirelessly via laptop3. Wirelessly via Windows-based PDA

14

LE

SA or SA/GK Multiturn actuator - Output Drives for many applications

Also available:

D / DD / B3D

IB3

AK

B

A

AF

15

SG05.1 – 12.1 Quarterturn Actuator

• 4 sizes (SG05.1 - SG12.1)

• up to 880 ft lbs output torque

• capable of ‘open/close’ service and ‘positioning’ or ‘modulating’ service up to 300 starts per hour

• variable operating time (single phase)

• separate splined coupling

• plug & socket electrical connection

• double seal available

• non-intrusive version available

• version available for hazardous locations according to FM, ATEX or CSA standards

16

SG.1 Quarterturn Actuator

Motor drives a three-stage planetary gear set which drives a worm/worm wheel gear set and finally a splined coupling. Hand wheel drives planetary gear housing then worm and coupling.

17

AUMA GS worm gearbox models

GS 50.3 – 125.3

GS 315 – 500

GS 160.3 – 250.3

12 sizes

GS50.3 – GS250.3

GS315 – GS500

GS630.3

Output torque up to 498,000 ft lbs

Wide variety of primary spur gear reducers

VZ on GS100.3 – GS125.3

GZ on GS160.3 – GS630.3

GS630.3

18

Model GS worm gear - Applications

Manual operator

Meets AWWA Standard C504-06 for manual butterfly valves (when properly selected)

Electric actuator for quarter turn applications

Electric actuator for guillotine damper applications

Electric actuator for diverter damper applications

Electric actuator for tainter gates

19

SA/GS Quarterturn Actuator

Multiturn actuator (model SA) directly coupled

worm gearbox (model GS)

worm gearbox / primary reducer combination (model GS/GZ)

Up to 498,000 ft lbs output torque for quarter turn applications

Combined features of SA actuator and GS worm gearbox

20

AM integral actuator controls

Used as the motor controls with SA, SAR and SG actuators.

21

AM integral actuator controls

Standard features:

reversing starters

plug & socket electrical connection – at field terminals and NORM actuator

power supply / transformer

phase correction

monitor relay

local controls

standard interface (contact closure/discrete inputs)

Options:

optional control system interfaces

Positioner – accepts 4-20 mA signalPulse timer board – extends operating timeDigital communications boards

solid state starters

22

AM integral actuator control package

Local controls:

3 pushbuttons (OPEN – STOP – CLOSE)

3 indicating lights (OPEN – FAULT – CLOSED)

Selector switch (LOCAL – STOP – REMOTE)

23

AM with fieldbus

®

P R O C E S S FIE L D B U S

24

AM Triple Play with fieldbus

DeviceNet

Standard features:

Reversing starters for motor control

Plug & socket electrical connection at field terminals and at NORM actuator

power supply / transformer

phase discriminator

local controls

Option:

solid state starters

25

AC01.2 integral actuator controls

Required for non-intrusive SA, SAR and SG.1 actuators

Can also be used as the motor controls for conventional SA, SAR & SG actuators.

26

AC01.2 actuator controls

Standard features:

Reversing starters for motor control

Plug & socket electrical connection at field terminals and at NORM actuator

Power supply / transformer for control power

Phase correction

Monitor relay

Programmable output relays (45 parameters available)

standard interface (contact closure / discrete inputs)

Local controls with LCD display

Diagnostics

Operational data logging

Electronic nameplate

Configurable via local controls or Bluetooth

Options

Adaptive positioner

Solid state starters

Digital communications / fieldbus / two-wire control

27

AC01.2 - local controls

Push-buttons: OPEN-STOP-CLOSE, RESET

5 indicating lights – programmable with 45 parameters available, for example:

End position CLOSED

End position OPEN

Fault

Selector switch in REMOTE

Actuator moving

Selector switch: LOCAL-OFF-REMOTE

Display on LCD

Valve position indication

Running indication

Setting menu

Status indication

Diagnostic information

28

AC01.2 with fieldbus

®

P R O C E S S FIE L D B U S

29

Commissioning / programming

From laptop or PDA via Bluetooth® interface

Connects actuator to AUMA PC software ToolSuite – Commissioning & Diagnostic Tool

30

Additional user-friendly features

31

Double-seal at terminal compartment

Available on all AUMA actuators

Seals terminal compartment from balance of actuator enclosure

32

AM and AC can be rotated on the NORM actuator.

Terminal compartment can be rotated on the actuator.

Local controls can be rotated on the AM or AC.

AM and AC.....flexible mounting

An AUMA exclusive feature!

33

Remote Mounting

Both the AM and AC can be remote mounted using an available wall bracket.

3434

A solution for any valve automation application

Spur gearboxes

Pedestal mounted/lever output actuators

Pedesatal mounted linear thrust units

35

AUMA ActuatorsElectric actuators for all applications

top related