bill components - australia
Post on 01-Jun-2018
219 Views
Preview:
TRANSCRIPT
-
8/9/2019 Bill Components - Australia
1/28
Understanding your Electricity Bill
Brisbane
PO Box 137, Greenslopes LPO, QLD 4120
P: +61 7 3367 1300
Melbourne
PO Box 118, Emerald VIC 3782
P: +61 3 5968 2117
Adelaide
PO Box 108, Dernancourt SA 5075
P: +61 407 945 547
13 August 2013
-
8/9/2019 Bill Components - Australia
2/28
Understanding your Electricity Bill
2
Disclaimer & limitations of this report
This analysis (the Guide) has been prepared by Solstice Development Services (SDS) Pty Ltd (Solstice) for the City of
Playford for the purpose of assisting businesses to better understand the structure and content of their electricity
bills to help them reduce costs (the Purpose).
The Guide was developed at the request of the City of Playford in conjunction with the development of the City of
Playford Elizabeth South Manufacturing Precinct - Alternative Energy Study.
The Guide should not be solely relied upon for investment or other decisions. Solstice reserves the right to review
and amend the Guide from time to time and to authorise in writing the use of the Guide for uses other than the
Purpose by City of Playford. Solstice accepts no responsibility or liability for damages or loss suffered in anyway
whatsoever resulting from any unauthorised use of the Guide.
The Guide has been prepared based upon information obtained from City of Playford, participating Elizabeth South
manufacturing precinct businesses, energy suppliers and services providers, and from public sources that have notbeen audited by Solstice. Whilst statements in this Guide are given in good faith, Solstice accepts no responsibility
for any errors in this information or the conclusions in this Guide.
The information in this Guide is commercially sensitive and subject to copyright and must not be used or reproduced
either in full, part or summary without the prior written consent of Solstice.
Revision History
Date Author Provided to Summary of Update
9 Aug 2013 D Willis L Harris First draft – City of Playford version - provided for
review.
13 Aug 2013 D Willis L Harris Final report – Guide with Case Studies.
-
8/9/2019 Bill Components - Australia
3/28
Understanding your Electricity Bill
3
Over recent years, electricity invoices together with electricity procurement have become more complex.
The electricity industry has experienced utility disaggregation; separation of networks from power generation and
electricity retail; privatisation; introduction of a national wholesale market; customers given the choice of multiple
suppliers; the introduction of renewable energy schemes; and most recently the introduction of a carbon tax that is
currently set to transition to an emissions trading scheme.
It has been difficult enough for electricity industry players to keep up, let alone electricity customers.
This guide is aimed at helping business customers better understand the current state of their electricity invoice.
The layout of the bill may change from Retailer to Retailer, but the content is pretty consistent across all suppliers.
On the following pages, each section of the bill is dissected and explained.
# Invoice Item Value
1 ACCOUNT DETAILS
Account Number 9999 9999
Supply Address 99 street name, suburb, state, postcode
Supply Period start 1 Mar 2013
Supply Period end 31 Mar 2013
Supply Period days 31
Invoice Issue date 2 Apr 2013
Payment due date 16 Apr 2013
METER DETAILS
2 Meter type Interval
3 NMI SAAAAAA000
4 Meter usage peak 20,000
5 Meter usage off peak 10,000
6 Total usage this period 30,000
7 DLF 1.0639
8 TLF 1.0029
9 Net Loss Factor 1.0670
# Invoice Item Units Quantity Units Rate (excl.energy losses)
Rate (incl.energy losses)
Charge(excl. GST)
Charge(incl. GST)
10 ENERGY CHARGES
11 Peak kWh 20,000 $/kWh $0.08500 $0.09069 $1,813.88 $1,995.26
12 Off Peak kWh 10,000 $/kWh $0.03500 $0.03734 $373.44 $410.79
13 Carbon Adjustment kWh 30,000 $/kWh $0.02000 $0.02134 $640.19 $704.21
14 NETWORK CHARGES Energy based network charge
15 Network Peak 1 kWh 1,666.7 $/kWh $0.19380 $323.01 $355.31
Network Peak 2 kWh 6,666.7 $/kWh $0.19281 $1,285.41 $1,413.95
Network Peak 3 kWh 8,333.3 $/kWh $0.19281 $1,606.74 $1,767.42
Network Peak 4 kWh 2,833.3 $/kWh $0.19281 $546.29 $600.92
16 Network Off Peak kWh 10,500.0 $/kWh $0.05497 $577.19 $634.90
17 Network Access Charge days 31 $/day $0.33547 $10.40 $11.44
18 RENEWABLE ENERGY CHARGES
19 REC - SRES - STC kWh 30,000 $/kWh $0.00768 $0.00817 $245.22 $269.74
20 REC - LRET - LGC kWh 30,000 $/kWh $0.00351 $0.00374 $112.17 $123.39
21 MARKET CHARGES
AEMO Pool Fees kWh 30,000 $/kWh $0.00040 $0.00042 $12.62 $13.88
AEMO Ancillary Charges kWh 30,000 $/kWh $0.00030 $0.00032 $9.58 $10.53
22 OTHER CHARGES
Retail Services days 31 $/day $1.23288 $38.22 $42.04
Meter Reading Fee meter days 31 $/meter/day $3.01370 $93.42 $102.77
Metering Charge meter days 31 $/meter/day $0.00000 $0.00 $0.00
TOTAL
23 Total kWh 30,000 $ $7,687.77 $8,456.55
24 Highest metered demand kVA 120.0 at: 14:00 on: Fri 1 Mar 2013
25 Carbon emissions tonnes 19.5
Carbon emissions intensity t CO2-e/MWh 0.6500
-
8/9/2019 Bill Components - Australia
4/28
Understanding your Electricity Bill
4
Account Details
# Notes
1 ACCOUNT DETAILS
The account details section identifies the customer’s Account Number and may also include a separateInvoice Number, and a record of the electricity supply address, which may be different to the billing address.
It will record the supply (or billing) period start and end dates and the number of billing days in the period.
Most large customers are on a monthly billing cycle, often coinciding with the calendar month start and finish
dates. Smaller customers are often on a quarterly billing cycle of around 90 days. Historically payments have
been due in arrears from around a few days to a couple of weeks after the invoice issue date.
Technical innovations in areas such as remote reading of meters, as opposed to the requirement for
someone to visit and manually record consumption has allowed Retailers to offer other alternatives with
respect to billing & payment cycles.
Increasingly, Retailers are offering a range of products to some customers including shorter billing cycles and
“bill smoothing” products which allow customers to pay a regular and constant amount with a periodic “true
up” once, or a number of times, per year to manage “unders and overs” (under estimation and over
estimation between actual meter reads).
This can help customers with greater budgeting and cash flow certainty and the reduction of administrative
transaction costs through the use of automatic payment methods like direct debit.
It also helps Retailers with cash flow management by reducing the duration of the accounts receivable cycle
that they face; which allows them to offer payment cycle related discounts including “pay on time” & “direct
debit” discounts.
Which elements are negotiable and which elements are not?
Whilst there are a large number of elements that make up an electricity bill, in practice many of these items are of a
"pass through" nature and the customer therefore can only check that they have been correctly applied and
calculated, rather than negotiate a lower rate.
As the bills have become more complex the propensity for errors has increased. Some anecdotal industry estimates
put the proportion of business customer energy invoices in error as high as 20% to 30%.
The key areas where customers can typically influence their bills are: Peak and Off Peak energy rates, plus associated
carbon charges (in order to accurately compare retail offers) and by ensuring the selection and maintenance of the
correct network tariff.
Some other minor charges like environmental imposts may be negotiable, but are less material.
# Invoice Item Value
1 ACCOUNT DETAILS
Account Number 9999 9999
Supply Address 99 street name, suburb, state, postcodeSupply Period start 1 Mar 2013
Supply Period end 31 Mar 2013
Supply Period days 31
Invoice Issue date 2 Apr 2013
Payment due date 16 Apr 2013
-
8/9/2019 Bill Components - Australia
5/28
Understanding your Electricity Bill
5
Meter Details
# Notes
METER DETAILS
2 Meter type
Some Retailers specify the meter type on the invoice. Meter type is identified typically as an “interval” meter
which records energy consumption and other information on a “time of day” basis, eg. ½ hourly; or an
“accumulation” meter which cumulatively records energy consumption and only records how much energy
was consumed between read times. For accumulation meters, the invoice will often show “Previous read”
quantity and “Current read” quantity.
The advent of “interval” meters has allowed the roll out of more sophisticated tariff products, including time-
of-day pricing that provide incentives for customers to use more or less energy at different times of the day
and days of the week.
3 NMI
The NMI or National Meter Identifier is a unique number for a customer’s metered connection point. A
customer may have more than one metered connection point and therefore have more than one NMI. A NMI
may also be associated with multiple meters at a single location.
A NMI is 10 characters long with an additional check digit eg: SAAAAAXXXX / X or 200XXXXXXX / X.
4 Meter usage peak
Peak usage is the quantity of electricity, measured in kilowatt hours (kWh), consumed during Peak times.
Peak hours may vary slightly from Retailer to Retailer, but typically in SA it refers to electricity consumed on
business days between the hours of 07:00 and 21:00 (Central Standard Time). Meters and meter readings are
not adjusted for daylight savings changes.
For customers with metering that does not recognise specific days, Peak energy is energy consumed on each
day between the hours of 07:00 and 21:00 (Central Standard Time).
For each NMI there may be separate accumulation "sub-meters" for Peak & Off-Peak consumption, or a
single interval meter from which Peak times can be distinguished from Off-Peak times.
5 Meter usage off peak
Off Peak usage refers to the quantity of energy consumed at times other than Peak times.
The concept of a “Shoulder” time period between Peak and Off-Peak times is really only used in NSW and the
ACT regions of the NEM, and does not typically apply in SA.
# Invoice Item Value
METER DETAILS
2 Meter type Interval
3 NMI SAAAAAA0004 Meter usage peak 20,000
5 Meter usage off peak 10,000
6 Total usage this period 30,000
7 DLF 1.0639
8 TLF 1.0029
9 Net Loss Factor 1.0670
-
8/9/2019 Bill Components - Australia
6/28
Understanding your Electricity Bill
6
# Notes
6 Total usage this period
Total usage is the sum of Peak usage and Off Peak usage. Based on the definition of Peak hours above, 40%of hours in the year are Peak hours and 60% are Off Peak.
In SA over the past 5 years, 46% of electricity demand occurred at Peak times and 54% at Off Peak times.
Electrical losses and loss factors
Electricity is “lost” during transport as it flows from power stations to consumers’ meters due to electrical
resistance and the heating of conductors. On average across the National Electricity Market (NEM) these losses are
the equivalent of approximately 10% of the total electricity generated by power stations.
Retailers buy electricity from the wholesale market and incur these losses in the transport of electricity to the
customer meter. The application of loss factors to the customer bill serves to compensate the Retailer for the cost
that they face associated with these losses as they have to pay the cost of the energy generated for their customers
including the losses from the common market reference point to the customer site.
The loss factors are used to either “scale up” the unit price of electricity and associated products or to “scale up”
the quantity of electricity. The effect of either method is the same.
On some invoices customers will see a unit price for electricity or “rate” exclusive of electrical losses and another
“rate” inclusive of electrical losses, which has been scaled up by the relevant loss factor.
Other customers will see an alternative approach for achieving the same result which uses a constant price rate but
increases the quantity. In this case a quantity, for example, of Peak energy that is the metered quantity is added to
another quantity to account for the losses related to that item without a price change.
The following diagram provides a simple illustration of the transport of electricity.
Source: AEMO
Losses across the high voltage Transmission system are accounted for using the TLF (transmission loss factor)
[sometimes referred to as the “MLF” or “Marginal Loss Factor”], and losses across the Distribution system are
accounted for using the DLF (distribution loss factor).
-
8/9/2019 Bill Components - Australia
7/28
Understanding your Electricity Bill
7
# Notes
7 DLF or Distribution Loss Factor
DLFs are recalculated annually by AEMO (Australian Energy Market Operator) and apply for a financial yearcommencing on 1 July. Different customer network tariff classes are allocated different connection point DLF
codes. Some very large customers connect directly to the transmission system and consequently do not have
a DLF. The rates that apply for FY2014, commencing 1 July 2013 and the comparison rates that applied in SA
for FY2013 are as follows:
Class Tariff Code FY2013 DLF FY2014 DLF
Low Voltage Unmetered NLV2 1.0800 1.0770
Low Voltage Residential NLV2 1.0800 1.0770
Low Voltage Controlled Load (hot water) NLV2 1.0800 1.0770
Low Voltage Business Single Rate NLV2 1.0800 1.0770
Low Voltage Business Two Rate NLV2 1.0800 1.0770
Low Voltage Transformer LV Demand NLV1 1.0639 1.0615
High Voltage HV Demand Two Rate NHV1 1.0381 1.0367
Substation Substation NZS1 1.0177 1.0170
Low Voltage refers to supply at a voltage of 230 volts single phase or 400 volts three phase.
High Voltage refers to supplies at voltages of 11,000 volts (11 kV) or 22,000 volts (22kV).
Substation class refers to supplies at sub-transmission level of 33,000 volts (33kV) or 66,000 volts (66kV).
8 TLF or Transmission Loss Factor (also known as “MLF” or “Marginal Loss Factor”)
TLFs are also recalculated annually by AEMO and apply for a financial year commencing on 1 July.
A TLF factor is associated with a Transmission Node Identities (TNI) Code which is related to a specific
transmission connection point or a virtual transmission node. Customer connections with an annual energy
consumption exceeding 160 MWh are typically assigned to a transmission connection point, taking into
account the normal network connections and predominant energy flows across that network. Smaller
customer connections with an energy consumption of 160MWh annually or less are assigned to the virtual
transmission node (VTN).
The relevant rates with respect to the Elizabeth South precinct that apply for FY2014, commencing 1 July
2013 and the comparison rates that applied for FY2013 are as follows:
Location Voltage TNI Code FY2013 TLF FY2014 TLF
SA virtual transmission node (VTN) SJP1 0.9981 1.0005
PARA substation 66 kV SPAR 1.0029 1.0036
Parafield Gardens West substation 66 kV SPGW 1.0020 1.0022
-
8/9/2019 Bill Components - Australia
8/28
Understanding your Electricity Bill
8
# Notes
9 Net Loss Factor
The Net Loss Factor is calculated as the product of the DLF and TLF.
In the case on this example invoice the Net Loss Factor is 1.0670 (1.0639 * 1.0029 = 1.0670) representing net
losses of 6.7% which are passed through to the customer.
Energy Charges
# Notes
10 ENERGY CHARGES
The energy charges are the key negotiable element of the electricity supply to be agreed with the Retailer.
Wholesale energy prices are set in a competitive spot market each half hour and the Retailer pays the
Australian Energy Market Operator (AEMO) to purchase electricity each half hour for supply to customers.
Because the National Electricity Market (NEM) spot market price can be highly volatile, Retailers also enter
into price hedging contracts with electricity generators (and other market traders) to manage the risk
associated with the price at which they buy wholesale electricity. Many Retailers also have their own power
generation facilities which acts as a natural hedge on their electricity purchases from the NEM (ie. they “sell”
energy to themselves via their own generation).
Consumption load shape or the amount of electricity consumed on week days versus weekends and during
the day versus overnight varies from customer to customer. Consequently, the effective cost of purchasing
that electricity from the wholesale market varies in terms of cost of sales to a Retailer for each customer. The
unpredictability of some customer loads also makes them more costly for the Retailer to manage because
the uncertainty affects the levels of hedging that they must undertake in advance via the financial markets.
To understand the potential load fluctuation and variation of customers, Retailers will often ask for historic
metering data or permission to access this historic half-hourly data. It is usually in the customer’s interest toprovide access to this data to the Retailer, because if they don’t have it then they may assume worse case
load fluctuation and shape than actually exists which will increase the energy charge prices to the customer.
To further mitigate the costs associated with load variations, Retailers may invoke an additional charge or a
right to re-price energy outside of permitted variations above or below an annual forecast, ie. variations
within +/- x% only are allowed. This Retailer contract clause too is usually negotiable.
On average, the energy charges (excluding carbon adjustment) typically make up around 30% to 40% of the
total electricity bill for business customers.
The following chart shows actual SA Peak and Off Peak average wholesale electricity prices monthly for
FY2013.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
10 ENERGY CHARGES
11 Peak kWh 20,000 $/kWh $0.08500 $0.09069 $1,813.88 $1,995.26
12 Off Peak kWh 10,000 $/kWh $0.03500 $0.03734 $373.44 $410.7913 Carbon Adjustment kWh 30,000 $/kWh $0.02000 $0.02134 $640.19 $704.21
-
8/9/2019 Bill Components - Australia
9/28
Understanding your Electricity Bill
9
Source: Solstice
# Notes
11 Peak
As the above chart shows, spot market Peak prices in SA exceeded Off Peak prices for each month during
FY2013.
The first Peak price appearing on the electricity invoice is referenced to the “Regional Reference Node” which
is a value before losses have been applied (nominally the “Regional Reference Node” refers to a common
wholesale market reference point in the SA region located in the 66kV switch yard at the Torrens Island
Power Stations). To convert this common market location Peak price to the customer’s meter, the net loss
factor is applied to the price to scale up the Peak price from the reference node to the meter. In the case of
this invoice example, the Peak price is “scaled up” by 6.7% (refer above to 9. Net Loss Factor).
An alternative method, which produces the same result, serves to scale up the quantity. Some Retailer
invoices show the metered Peak electricity consumption quantity and an additional quantity to account for
losses (in kWh) from the Regional Reference Node to the meter.
The above chart shows a full year of monthly Peak and Off Peak wholesale electricity spot prices in SA.
The following chart looks back by month over 5 years to show that while both Peak and Off Peak prices did
rise overall coincident with the implementation of the carbon tax from July 2012, there are other market
effects that can see very high price spikes in the electricity market (eg. caused by extreme weather events or
significant power station breakdowns and outages). It is this type of volatility that can have a large impact on
average monthly wholesale spot prices and ultimately impact what prices Retailers decide to charge
Customers.
0
20
40
60
80
100
120
140
160
180
200
$ / M W h
SA spot market wholesale prices FY2013
Average Peak Price Average Off Peak Price
-
8/9/2019 Bill Components - Australia
10/28
Understanding your Electricity Bill
10
Source: Solstice
# Notes
12 Off Peak
Off Peak energy pricing rates are pretty much always at or below Peak pricing rates.
The calculation treatment of Off Peak prices to account for losses is the same as described above for Peak
pricing.
13 Carbon Adjustment
Some Retailers offer the choice of including the carbon price in the Peak and Off Peak energy prices as an
alternative to identifying the carbon charge explicitly on the invoice.The charge associated with the carbon tax is referred to as a “carbon adjustment” on most Retailer invoices.
The carbon tax commenced from 1 July 2012 and is applied to large emitters of carbon dioxide, including
fossil (eg. coal, gas) fuelled power stations. The application of the carbon tax is designed to provide a
financial incentive to electricity producers to reduce carbon emissions by using less carbon intensive
technologies to generate electricity and to substitute going forward with “cleaner” technologies.
The resulting increased costs associated with electricity production through the inclusion of the tax and/or
the use of more expensive, but less carbon intensive, technologies flows through into the wholesale
electricity market.
The key factors that contribute to the carbon adjustment for the customer include the:
actual carbon tax (price) rate, which was fixed at $23 per tonne for FY2013, increasing to $24.15 for
FY2014, and thereafter will have either one more year at a fixed price, or will be allowed to “float”
with the price set by the market;
0
50
100
150
200
250
300
350
400
450
500
550
$ / M W h
SA spot market wholesale prices FY2008 to FY2013
Average Peak Price Average Off Peak Price
-
8/9/2019 Bill Components - Australia
11/28
Understanding your Electricity Bill
11
NOTE: The Federal Opposition has announced that they will remove the carbon tax if elected to
Government at the 2013 election. The proposed timing and transaction arrangements are not known
at the time of producing this guide.
the carbon intensity (quantity) rate, which is the amount of carbon emitted per unit of electricity
production. This carbon intensity rate varies by power station (eg. the carbon intensity rate of a coalfired power station is greater than gas fired, etc.) and on average from state to state (eg. Victoria is
high because the generation fleet is dominated by high CO2 producing brown coal fuelled generation,
and Tasmania is low as it is dominated by zero emission hydro power generation); and
the net loss factor, to scale up the carbon adjustment rate from the regional reference node to the
meter.
Carbon emissions rates to be applied by Retailers on customer bills are not regulated which makes the
“carbon adjustment” a potentially negotiable element of the electricity bill.
In the short-term, while the carbon tax “price” is fixed, negotiation will only be around the rate of emissions
intensity. If the carbon tax remains and the carbon tax regime transitions to an emissions trading scheme
(ETS), which is the current policy of the current government, the “price” will float and be set by marketmechanisms which will mean both the price and rate of intensity will effectively be negotiable.
The variation in actual emissions intensity varies significantly from State to State. The following table shows
the average for each NEM state and the NEM as a whole for FY2013 in tonnes of carbon dioxide equivalent
emissions per megawatt hour of electricity production (tCO2-e/MWh):
Period NEM NSW QLD SA TAS VIC
FY2013 0.8750 0.9038 0.8382 0.5169 0.0581 1.1773
To put this value in perspective using the FY2013 fixed price of $23 per tonne, and comparing the NEMaverage intensity with the SA average intensity, and using the same net loss factor of 1.0670:
NEM intensity = $23 * 0.8750 * 1.0670 = $21.47 per MWh or 2.147 cents per kWh.
SA intensity = $23 * 0.5169 * 1.0670 = $12.68 per MWh or 1.268 cents per kWh.
That is to say that the SA average emissions intensity was at a 41% discount to the NEM average emissions
intensity over FY2013.
From a sample of business customer invoices in the City of Playford reviewed during FY2013 it appears that
Retailers are using a range of intensity rates around the NEM average rather than the SA average.
For a business customer consuming 300MWh per year in FY2013:
NEM intensity: $6,441 carbon adjustment
SA intensity: $3,804 carbon adjustment
Difference: -$2,637
The Retail contract with the customer should specify the carbon rate and intensity or method to be applied
on the invoice. As the simple illustration above highlights, it is potentially an important part of contract
negotiations.
Retailers may differ with respect to their individual policies on how they will recover the costs they face with
respect to the carbon imposts. Some may choose to smear the same emissions rate across their national
customer base and others may choose to differentiate by State. The key point to note is that whencomparing quotes and offers from Retailers during periodic energy procurement cycles, the treatment of this
new carbon impost could alter the customer’s selection of preferred Retailer.
-
8/9/2019 Bill Components - Australia
12/28
Understanding your Electricity Bill
12
Network Charges
# Notes
14 NETWORK CHARGES
Network tariffs are regulated by the Australian Energy Market Commission (AEMC) and prices are publishedannually for each financial year commencing from 1 July.
There are two network service providers (NSPs) in South Australia:
ElectraNet, a transmission network service provider (TNSP), which owns and manages the high-
voltage electricity transmission network; and
SA Power Networks (SAPN) (formerly known as ETSA Utilities), a distribution network service
provider (DNSP), which owns and manages the low-voltage electricity distribution network.
The Retailer collects network charges from the customer on behalf of the NSPs and passes that regulated
revenue through to the NSPs. The network charges cover the regulated costs of the NSPs for building,
managing and maintaining the transmission and distribution wires network assets including some customer
metering.
Various network tariffs are set for different types of customers. In some cases there may be more than one
network tariff that is potentially applicable to a customer. It is in the customer’s interest to be on the lowest
cost network tariff and this should be reviewed periodically to confirm that the customer remains on the
optimal tariff for their circumstances.
Some network tariffs are largely “energy based” which tends to make them a low fixed cost, but relatively
high variable cost tariff. Other network tariffs are largely “demand or capacity based” which tends to make
them a high fixed cost, but relatively low variable cost.
Irrespective of the network tariff type, no losses (DLFs or TLFs) are applied to network charges.
The case studies show more specific details, but the following chart illustrates the situation for a businesscustomer consuming approximately 375,000kWh per year, with a maximum demand of 120 kVA.
The comparison made is between the “Business 2 rate” tariff (low fixed, high variable), and the “Low Voltage
Stepped Demand” tariff (high fixed, low variable).
Assuming a power factor of unity with 66% of energy consumed at Peak times, the example customer is
approximately $16,000 per year (30%) better off on the Low Voltage Stepped Demand tariff than the
Business 2 rate tariff.
If the customer’s annual consumption was below approximately 225,000 kWh however, the customer would
be better off on the Business 2 rate tariff.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
14 NETWORK CHARGES Energy based network charge
15 Network Peak 1 kWh 1,666.7 $/kWh $0.19380 $323.01 $355.31Network Peak 2 kWh 6,666.7 $/kWh $0.19281 $1,285.41 $1,413.95
Network Peak 3 kWh 8,333.3 $/kWh $0.19281 $1,606.74 $1,767.42
Network Peak 4 kWh 2,833.3 $/kWh $0.19281 $546.29 $600.92
16 Network Off Peak kWh 10,500.0 $/kWh $0.05497 $577.19 $634.90
17 Network Access Charge days 31 $/day $0.33547 $10.40 $11.44
-
8/9/2019 Bill Components - Australia
13/28
Understanding your Electricity Bill
13
Source: Solstice
# Notes
15 Network Peak (energy based network tariff)
Network Peak energy refers to energy consumed on business days between the hours of 07:00 and 21:00
(Central Standard Time). This is also typically the definition of Retail Peak energy in SA, but some Retailers
may have a slightly different definition, e.g. if adopting the NEM definition of Peak period which refers to
energy consumed on business days between the hours of 07:00 and 22:00 (Eastern Standard Time).
For Distribution Network Users with metering that does not recognise specific days, Peak energy is energy
consumed on each day between the hours of 07:00 and 21:00 (Central Standard Time).
Due to this potential for different definitions of Peak time periods between the NSP and Retailer, there are
sometimes slight differences on the invoice with regard to the quantity of Peak energy for the invoice period
between the energy charges and network charges.
There are numerous types of network tariffs that may apply.
The example shown on this illustrative invoice is an “energy based” network tariff that is largely a variable
charge based on the level of consumption (kWh).
This Monthly Low Voltage Business Two Rate tariff has 4 Peak charging blocks, with a separate price for each
incremental block, as follows:
Peak Block 1 Usage Rate: First 1,666.7 kWh per month (effective proxy for 20,000 kWh per year); Peak Block 2 Usage Rate: Next 6,666.7 kWh/month (next 80,000 kWh p.a.);
Peak Block 3 Usage Rate: Next 8,333.3 kWh/month (next 100,000 kWh p.a.); and
Peak Block 4 Usage Rate: Balance of usage beyond 16,666.7 kWh/month (beyond 200,000 kWh p.a.).
$-
$5,000
$10,000
$15,000
$20,000
$25,000
$30,000
$35,000
$40,000
$45,000
$50,000
$55,000
$60,000
N e t w o r k C o s t s
kWh
Network Options-375-PF1
Network Total (Business 2 Rate) Network Total (Low Voltage Stepped Demand)
-
8/9/2019 Bill Components - Australia
14/28
Understanding your Electricity Bill
14
However, whilst 4 different pricing blocks are published, only 2 different prices apply. They are for the first
1,666.7 kWh per month which is charged at 19.38 cents per kWh (FY2013 excluding GST), and then any
volume above 1,666.7 kWh per month is charged at 19.281 cents per kWh.
Note that these network charges are only to cover payment for the use of the transmission and distribution
“wires” for the month and these charges are passed straight through from the Retailer to the NSPs.
These charges are regulated and not negotiable (however, the customer may find that they can take
advantage of a more attractive network tariff – see the Case Studies following for more detail).
16 Network Off Peak (energy based network tariff)
Network Off Peak energy refers to energy consumed at times other than Peak times.
The Monthly Low Voltage Business Two Rate tariff has only 1 Off Peak charging block and all Off Peak energy
quantity has a network charge, in this example, of 5.497 cents per kWh (FY2013 excluding GST).
Note that these network charges are only to cover payment for the use of the transmission and distribution
“wires” for the month and these charges are passed straight through from the Retailer to the NSPs.
These charges are regulated and not negotiable.
17 Network Access Charge (energy based network tariff)
In addition to the energy based Peak and Off Peak variable network charges under the Monthly Low Voltage
Business Two Rate tariff, there is also a day based charge of 33.547 cents per day (FY2013 excluding GST).
This Supply Rate may also be referred to as a Network Access Charge on some Retailer invoices.
The Network Access Charge is also regulated and not negotiable.
Capacity based (stepped demand) network charges
The alternative primary pricing structure for network charges within the range of network tariffs is largely “capacity
based” as opposed to the previously described “energy based” tariff structure.
The following example describes the key elements of one of these capacity based network charging structures using
the Low Voltage Stepped Demand (minimum 80 kVA) (VLVS) tariff.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
14 NETWORK CHARGES Capacity based network charge
15a Network Peak kWh 20,000 $/kWh $0.03723 $744.60 $819.06
16a Network Off Peak kWh 10,000 $/kWh $0.03723 $372.30 $409.53
17a1 Demand Step 1 kVA 100.0 $/kVA/mth $17.90703 $1,790.70 $1,969.77
17a2 Demand Step 2 kVA 20.0 $/kVA/mth $12.02490 $240.50 $264.55
17a3 Demand Step 3 kVA 0.0 $/kVA/mth $9.81889 $0.00 $0.00
17a4 Demand Step 4 kVA 0.0 $/kVA/mth $8.34702 $0.00 $0.00
17a5 Additional Demand kVA 0.0 $/kVA/mth $4.55851 $0.00 $0.00
-
8/9/2019 Bill Components - Australia
15/28
Understanding your Electricity Bill
15
# Notes
15a Network Peak (capacity based network tariff)
The Network Peak energy charge is applied as a rate per kWh of energy consumed during Peak times on theVLVS tariff in the same way as similar rates are applied in the above energy based (Monthly Business 2 rate)
network charge example. However, under the VLVS tariff there is only a single rate of 3.723 cents per kWh
(FY2013 excluding GST) that applies for all Peak energy (as opposed to the 4 block tariff regime that applies
to the Monthly Business 2 rate network tariff). This variable rate is much lower on the VLVS tariff which is
dominated by the capacity or stepped demand charges.
These charges are regulated and not negotiable.
16a Network Off Peak (capacity based network tariff)
There is also only a single Network Off Peak energy charge applied as a rate per kWh under the VLVS tariff.
The Off Peak energy charge in this case is the same as the Network Peak energy charge of 3.723 cents per
kWh (FY2013 excluding GST).
These charges are regulated and not negotiable.
17a1 Network Demand Step 1 Charge (capacity based network tariff)
In addition to the energy based Peak and Off Peak variable network charges under the VLVS tariff, there is
also a series of capacity or stepped demand based charges.
These demand charges are determined on the basis of:
agreed maximum “Annual Demand” (which occurs within an SAPN specified period); and
agreed maximum “Additional Demand” (which occurs at any other time in the year).
Agreed Annual Demand is the highest demand expected to be required in the period 12:00 to 20:00 on
working days in December through March (Central Standard Summer Time). This may be determined by
agreement or by historically recorded demand. This time of day on work days through Summer and March is
when the coincident customer Peak demands on the network are at their highest.
Agreed Additional Demand is the amount, if any, that the Agreed Anytime Demand exceeds the Agreed
Annual Demand.
Agreed Anytime Demand is the highest demand expected to be required outside of the times that the Agreed
Annual Demand applies. This may be determined by agreement or by historically recorded demand. This may
be equal to or higher than the Agreed Annual Demand but not less.
This overall structure gives customers a price incentive to avoid achieving their annual maximum demand
during the period from noon till 8pm (Central daylight saving time) on working weekdays over the months of
Summer and March each year.
The Low Voltage Stepped Demand (VLVS) tariff has 5 demand step charging blocks, with a separate price for
each incremental block.
These charges are regulated and not negotiable.
The Demand Step 1 charge is $17.90703 per kVA per month (FY2013 ex GST) for the first 100 kVA and with a
minimum of 80 kVA applied.
-
8/9/2019 Bill Components - Australia
16/28
Understanding your Electricity Bill
16
# Notes
17a2 Network Demand Step 2 Charge (capacity based network tariff)
The Demand Step 2 charge is $12.0249 per kVA per month (FY2013 ex GST) for the next 150 kVA.
17a3 Network Demand Step 3 Charge (capacity based network tariff)
The Demand Step 3 charge is $9.81889 per kVA per month (FY2013 ex GST) for the next 750 kVA.
17a4 Network Demand Step 4 Charge (capacity based network tariff)
The Demand Step 4 charge is $8.347020 per kVA per month (FY2013 ex GST) for the kVA balance beyond1,000 kVA.
17a5 Network Additional Demand Charge (capacity based network tariff)
The Demand Step 5 charge for Additional Demand is $4.55851 per kVA per month (FY2013 ex GST) to the
extent, if any, that the Agreed Anytime Demand exceeds the Agreed Annual Demand in kVA.
These charges are regulated and not negotiable.
-
8/9/2019 Bill Components - Australia
17/28
Understanding your Electricity Bill
17
Renewable Energy Charges
# Notes
18 RENEWABLE ENERGY CHARGES
The Mandatory Renewable Energy Target (MRET) scheme was introduced by the Federal Government to
encourage investment in low emissions renewable energy power generation, and commenced in 2001.
This scheme evolved into two parts from January 2011 which operate as:
Large-scale Renewable Energy Target (LRET); and
Small-scale Renewable Energy Scheme (SRES).
Both schemes are currently planned to run until 2030.
LRET is designed to encourage the deployment of large-scale renewable energy projects such as wind farms.
SRES is designed to support the installation of small-scale systems, including solar photo-voltaic (PV) panels
and solar water heaters.
LRET & SRES require electricity Retailers to purchase a mandated quantity of renewable energy certificates
each compliance year (calendar year) and surrender those certificates to the Clean Energy Regulator.
Certificates related to the LRET are called LGCs (Large scale Generation Certificates).Certificates related to the SRES are called STCs (Small scale Technology Certificates).
The LRET and SRES are Federal Government initiatives. There are also a number of other State Government
based renewable energy schemes, but none currently operate in South Australia that appear as a separate
charge on customer invoices.
The renewable energy charges on the customer bill are how the Retailer recovers the cost of its mandatory
LGC & STC surrender obligations.
19 REC – SRES – STC
Retailers, as “liable entities” are required to purchase and surrender STCs based on the size of their electricity
loads (ie. the loads of their customers). The quantity of STCs that Retailers must surrender each year is
determined by the Small-scale Technology Percentage (STP) which is set annually (calendar year) by the
Clean Energy Regulator according to the Regulations.
The Retailer must pay a penalty for any shortfall in the surrender of their STCs to the Regulator. The Small-
scale Technology Shortfall Charge (STSC) is currently $65 per STC. However, as the shortfall charge is not
deductible for income tax purposes, the effective penalty is closer to $93 per STC which is the shortfall
charge divided by the reciprocal of the Company Income Tax Rate (ie. $65/(1-30%) = $92.86). In practice
Retailers purchase most if not all of their requirements to avoid shortfall penalties.
The STP for calendar year 2013 (CY2013) is 19.7%, meaning that a Retailer must purchase and surrender 197STCs for every 1,000 MWh of electricity that it purchases from the wholesale market on behalf of its
customers.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
18 RENEWABLE ENERGY CHARGES
19 REC - SRES - STC kWh 30,000 $/kWh $0.00768 $0.00817 $245.22 $269.7420 REC - LRET - LGC kWh 30,000 $/kWh $0.00351 $0.00374 $112.17 $123.39
-
8/9/2019 Bill Components - Australia
18/28
Understanding your Electricity Bill
18
STCs are a tradeable commodity attached to eligible installations of SRES systems with a maximum threshold
size of 100kW (eg. for solar PV).
The Australian Government has capped the price of STCs at $40 per MWh (4 cents per kWh) but the actual
value of an STC varies from day to day. STCs are traded on the STC market meaning the price will vary
according to supply and demand. As at the end of July 2013, CY2013 STCs traded at ~$39 per MWh (3.9 centsper kWh).
Based on July 2013 STC market prices, the indicative cost to the Retailer for CY2013 is approximately:
$39 * 19.7% = $7.683 per MWh or 0.7683 cents per kWh.
However, the Retailer incurs theoretical losses when recovering the cost of STCs from customers. The losses
associated with STCs do not include transmission losses, but only distribution losses, ie. The DLF is included
and the TLF is excluded.
Consequently, using the cost base of $39 per STC and the DLF in the example invoice of 1.0639, the indicative
(no margin) pass through price from the Retailer to the customer for CY2013 is approximately:
$39 * 19.7% * 1.0639 = $8.174 per MWh or 0.8174 cents per kWh.
Recent STC prices have ranged from mid to high $20s in early FY2013 to just below the $40 cap price at the
end of FY2013:
Source: EUAA
These charges will vary from Retailer to Retailer and over time and while relatively minor, may be negotiable.
20 REC – LRET – LGC
Retailers, as “liable entities” are required to purchase and surrender LGCs based on the size of their
electricity loads (ie. the loads of their customers). The quantity of LGCs that Retailers must surrender each
year is determined by the Renewable Power Percentage (RPP) which is set annually (calendar year) by the
Clean Energy Regulator according to the Regulations.
The Retailer must pay a penalty for any shortfall in the surrender of their LGCs to the Regulator. The Large-
scale Generation Shortfall Charge (LGSC) is currently $65 per LGC. However, as the shortfall charge is not
deductible for income tax purposes, the effective penalty is closer to $93 per LGC which is the shortfall
charge divided by the reciprocal of the Company Income Tax Rate (ie. $65/(1-30%) = $92.86). In practice
Retailers purchase most if not all of their requirements to avoid shortfall penalties. Plus some Retailers invest
-
8/9/2019 Bill Components - Australia
19/28
Understanding your Electricity Bill
19
in renewable projects such as wind and solar directly to generate LGCs.
The RPP for calendar year 2013 (CY2013) is 10.65%, meaning that a Retailer must purchase and surrender
106.5 LGCs for every 1,000 MWh of electricity that it purchases from the wholesale market on behalf of its
customers.
LGCs are a tradeable commodity created by accredited RET power stations at a rate of 1 LGC for every MWh
of eligible renewable electricity generated above the power station's baseline.
There is no explicit price cap for LGCs, however, the Large-scale Generation Shortfall Charge (LGSC) described
above sets an effective cap price.
LGCs are traded in the open market, where the price will vary according to supply and demand and the actual
value of an LGC varies from day to day. As at the end of July 2013, CY2013 LGCs traded at ~$33 per MWh (3.3
cents per kWh).
Based on July 2013 LGC market prices, the indicative cost to the Retailer for CY2013 is approximately:
$33 * 10.65% = $3.515 per MWh or 0.3515 cents per kWh.
However, the Retailer incurs theoretical losses when recovering the cost of LGCs from customers. The losses
associated with LGCs do not include transmission losses, but only distribution losses, ie. The DLF is included
and the TLF is excluded.
Consequently, using the cost base of $33 per LGC and the DLF in the example invoice of 1.0639, the indicative
(no margin) pass through price from the Retailer to the customer for CY2013 is approximately:
$33 * 10.65% * 1.0639 = $3.739 per MWh or 0.3739 cents per kWh.
Recent CY2013 LGC prices have ranged from low $40s in early FY2013 to low $30s at the end of FY2013:
Source: EUAA
Forward LGC prices for CY2014 have tracked at about $1 to $2 above CY2013 over the past year, and forward
LGC prices CY2015 have tracked at about $2 to $4 above CY2013 over the same period.
These charges will vary from Retailer to Retailer and over time and while relatively minor, may be negotiable.
-
8/9/2019 Bill Components - Australia
20/28
Understanding your Electricity Bill
20
Market Charges
# Notes
21 MARKET CHARGES
Retailers, as participants in the NEM, are obliged to pay fees to AEMO to cover:
A share of the annual operating costs of AEMO as the market operator; and
Ancillary services which are other costs associated with operating and maintaining a stable and
reliable interconnected electricity system.
AEMO Pool Fees
AEMO Pool Fees (or Market Fees) are allocated to Retailers by AEMO on a rate per MWh basis based on the
size of their electricity loads (ie. the loads of their customers). The AEMO budget is re-set annually on a
financial year basis commencing from 1 July each year. The Retailer rate for FY2013 was $0.3954 per MWh
excluding GST (0.0004 cents per kWh).
To fully cover the cost of AEMO Pool Fees the Retailer needs to scale up by the Net Loss Factor (TLF & DLF) in
the pass through to the customer, which increases the charge using the same net loss factor of 1.0670 to:
AEMO Pool Fees = $0.3954 * 1.0670 = $0.4219 per MWh or 0.00042 cents per kWh.
AEMO Ancillary Charges
Ancillary services are those services used by AEMO to manage the power system safely, securely and reliably.
These services maintain key technical characteristics of the system, including standards for frequency,
voltage, network loading and system restart processes.
AEMO operates eight (8) separate markets for the delivery of frequency control ancillary services (FCAS) and
purchases network control ancillary services (NCAS) and system restart ancillary services (SRAS) under
agreements with service providers.
The actual ancillary services costs to AEMO can vary significantly from week to week.
AEMO recovers some ancillary services costs (around 40% to 50%) on a “causer pays” basis which is largely
met by the generation power stations. The balance of ancillary services is recovered primarily from the
Retailers.
The Retailers’ share of AEMO Ancillary Charges over FY2013 were approximately $0.30 per MWh excluding
GST (0.0003 cents per kWh).
To fully cover the cost of AEMO Ancillary Charges the Retailer needs to scale up by the Net Loss Factor (TLF &
DLF) in the pass through to the customer, which increases the charge using the same net loss factor of 1.0670
to:
AEMO Ancillary Charges = $0.30 * 1.0670 = $0.3192 per MWh or 0.00032 cents per kWh.
Both of these charges are typically treated as a pass through and if passed through at cost are essentially notfor negotiation.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
21 MARKET CHARGES
AEMO Pool Fees kWh 30,000 $/kWh $0.00040 $0.00042 $12.62 $13.88AEMO Ancillary Charges kWh 30,000 $/kWh $0.00030 $0.00032 $9.58 $10.53
-
8/9/2019 Bill Components - Australia
21/28
Understanding your Electricity Bill
21
Other Charges
# Notes
22 OTHER CHARGES
There are a number of other charges that may appear on the customer invoice.
These other charges are typically charged on a per day, per month, per meter or per NMI basis rather than an
energy or capacity basis. As a consequence of their charging basis, these other charges are not typicallyscaled up for losses.
Retail Services
Retail services may cover value added services provided by the Retailer or another third party, including for
example such items as:
Bill reconciliation services;
Energy consumption reporting; and
Emissions reporting.
Retail services fees (or “Administration charges”) may be negotiable and vary on a case by case basisdepending on the type and extent of value added services provided.
Meter Reading Fee & Metering Charge
The meter reading fee refers to the cost of services typically provided by the meter data provider which may
be limited to meter data: acquisition, monitoring, warehousing and transfer; or include other value added
reporting services.
The metering charge fee relates to payment for the use of the physical meter, including the supply,
installation, testing and audit of the meters. Depending on the network tariff type and selected metering
provider, the metering charge may be an explicit charge or it may be included in the network charges sectionof the invoice.
It is not unusual to see a single consolidated “Metering Services” item on the invoice which covers both
meter reading (meter data provider) fees and metering charges.
The meter reading fee & metering charge may represent a combination of negotiable charges and/or pass
through charges from the Retailer.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
22 OTHER CHARGES
Retail Services days 31 $/day $1.23288 $38.22 $42.04Meter Reading Fee meter days 31 $/meter/day $3.01370 $93.42 $102.77
Metering Charge meter days 31 $/meter/day $0.00000 $0.00 $0.00
-
8/9/2019 Bill Components - Australia
22/28
Understanding your Electricity Bill
22
Total
# Notes
TOTAL
23 Total
The total item on the invoice will sum up the total electricity consumption for the invoice period, plus thetotal amount payable, typically with and without GST.
24 Highest metered demand
For customers with interval metering, and particularly those on capacity based network tariffs, the highest
metered demand (maximum demand) for the invoice period together with the date and time that it occurred
will be reported.
The Power Factor may also be reported together with maximum demand. Power Factor is essentially a type
of efficiency measure. The power factor of a load is given by the ratio of kW (active power) divided by kVA
(apparent power) at any given moment. The value of a power factor will range from 0 to 1.
A power factor close to unity means that the reactive energy is small compared with the active energy, while
a low value of power factor indicates the opposite condition. The closer the power factor approaches its
maximum possible value of 1, the greater the benefit to the customer and the supplier. Network service
providers may require customers to install power factor correction equipment if the power factor is
consistently outside of the required standard, and for some network tariffs the power factor may impact the
network charge.
25 Carbon emissions
Carbon emissions are typically reported on the invoice as “estimated greenhouse gas emissions for this bill”
in tonnes of carbon dioxide equivalent for the period.
However, the emissions intensity rate (discussed in detail at “13. Carbon Adjustment” above) may not be
made explicit. This rate can be simply calculated by dividing the reported tonnes of carbon dioxide by the
electricity consumption (in MWh, ie. kWh divided by 1,000) for the invoice period.
This calculated emissions intensity rate may not reconcile with the emissions intensity rate that the customer
is being charged via the carbon adjustment for a number of possible reasons including:
The estimated reporting rate being used is different to the carbon adjustment charge rate;
The total electricity consumption has not been adjusted for losses, but the carbon emission rate has
or vice versa.
The carbon emissions are often reported in a chart together with monthly electricity consumption.
# Invoice Item Units Quantity Units Rate (excl.
energy losses)
Rate (incl.
energy losses)
Charge
(excl. GST)
Charge
(incl. GST)
TOTAL
23 Total kWh 30,000 $ $7,687.77 $8,456.5524 Highest metered demand kVA 120.0 at: 14:00 on: Fri 1 Mar 2013
25 Carbon emissions tonnes 19.5
Carbon emissions intensity t CO2-e/MWh 0.6500
-
8/9/2019 Bill Components - Australia
23/28
Understanding your Electricity Bill
23
Case Studies
The foregoing guide has dissected and explained each section of the typical electricity bill in detail for a theoretical
business customer in South Australia.
Actual electricity invoices were gathered from a sample of 11 companies in the Elizabeth South precinct of the Cityof Playford in the first half of 2013 as part of the Elizabeth South Manufacturing Precinct, CleverGreen Eco-
Innovation Program, Alternative Energy Study.
While anonymity with respect to this confidential pricing data is being maintained for the wider sample group, two
businesses agreed to disclose their electricity pricing information and experience for the purposes of these case
studies.
The following chart summarises the average total cost of delivered electricity (including carbon adjustments and
network charges, and excluding GST) taken from individual bills issued in late 2012 and early 2013. The chart shows
that average costs varied widely across the Elizabeth South precinct from a low of approximately $0.17/kWh (17
cents per kilowatt hour) to a high which is double that rate at $0.34/kWh.
Source: Solstice
It is clear from the above chart that the dominant 3 elements of the electricity bill are the network charges,
electricity price (excluding carbon), and the carbon charge. Of these elements, the electricity price (Peak rate and Off
Peak rate) is negotiable, the network charge is a regulated pass through, and the carbon price has only been in
existence since July 2012.The cost stacks represented in this chart for Levett Engineering Pty Ltd and Sonnex Engineering Pty Ltd, who are the
case study subjects, both represent the “before” case.
02468
1012141618202224262830
3234363840
Levett
Engineering
Sonnex
Engineering
c e n t s p e r k W h
City of Playford - Elizabeth South Precinct - Participant Companies
Grid Supply Total Charges (2013)Other Metering Retail ServiceCarbon (environmental) STC (environmental) LGC (environmental)Network Ancillary Services (market) AEMO Fees (market)Electricity price (excl Carbon)
25.7 c/kWh
33.9 c/kWh
-
8/9/2019 Bill Components - Australia
24/28
Understanding your Electricity Bill
24
During the process of the review of the sample of electricity contracts and invoices that were supplied, evidence was
discovered of:
Discrepancies between agreed contracted rates and invoiced rates for some customers;
Discrepancies between published regulated network charges and the invoiced rates for those pass-throughcharges;
Some customers on un-competitive (relatively high) electricity rates; and
Some customers on sub-optimal (very high) network tariffs.
In addition with respect to invoice charges related to the carbon tax that was implemented in July 2012, it was
identified that:
Carbon intensity charge rates were inconsistent with reported carbon emissions rates; and
Carbon intensity rates used for carbon adjustment charges generally were around national benchmark
measures which were above the benchmark measures reported for South Australia.
Levett & Sonnex Case Studies
The individual case studies that follow provide details of savings identified and achieved by the two participating
businesses of approximately $70,000 per year:
Levett Engineering: saved $16,000 p.a.
reducing the total bill by 17% from $95,000 to $79,000 per year by moving to an optimal network tariff.
Sonnex Engineering: saved $54,000 p.a.
reducing the total bill by 30% from $181,000 to $127,000 per year by moving to an optimal network tariffand negotiating a lower Peak and Off-Peak energy price.
-
8/9/2019 Bill Components - Australia
25/28
Understanding your Electricity Bill
25
Case Study – Levett Engineering
Levett Engineering Pty Ltd is an advanced parts manufacturer for aeronautical, defence, agriculture and other
commercial industries. Levett manufactures for domestic and export markets (e.g. US & UK), including commercial
and military aircraft parts, and component manufacture for the F35 Joint Strike Fighter aircraft program.The Elizabeth South site currently operates 2 shifts per day over 5 days per week, but remains day shift dominant
with a "skeleton" afternoon shift, employing 35 full time equivalent (FTE) personnel. The business is expected to
grow to 3 shifts when the F35 Joint Strike Fighter aircraft manufacture moves to full production and the workforce is
expected to grow to approximately 50 FTE. Major loads at the site include: milling machines & lathes.
The following table summarises the Levett electricity consumption for the 12 months ending 30 April 2013.
Source: Solstice
Source: Solstice
Load Characteristics
The Levett load fluctuates throughout the year
with demand from the production schedule,
which is evidenced from the Daily Max, Min &
Average load data.
Excluding the Christmas holiday period & Easter,
the maximum week day load ranged from
around 60kW to 110kW over the 12 month
sample period.
Analysis of the half hourly data shows that
Levett is at or above 56kW load (50% of
maximum load) for about 44% of the time, and
uses the top 10% of its maximum load for only
about 0.12% of the time.
Price CharacteristicsThe Levett cost of key elements including Peak
and Off Peak electricity prices and carbon
adjustment are comparable with Levett’s peers.
Network costs however, whilst charged as a pass
through at regulated rates appear relatively high
with Levett on a Monthly Business 2 Rate
network tariff.
Financial Year 2013 total electricity expenditure
(excluding GST)
Total annual spend: $95,065Average annual spend: $0.257/kWh
Source: Solstice
Statistic Units Value Note
Electricity consumption kWh pa 372,160
Peak Electricity consumption kWh pa 243,960 66%
Off Peak Electricity consumption kWh pa 128,200 34%
Maximum demand kW 111 at 09:30 on Tue 29 May 2012
Minimum demand kW 2 at 08:00 on Wed 26 Dec 2012
Average demand kW 42
Load Factor % 38%
0
20
40
60
80
100
120
D a i l y D e m a n d ( k
W )
Daily Maximum, Minimum & Average Load
Daily Max Load Daily Min Load Daily Average Load
0
2468
10121416182022242628303234
Peak Off Peak Average
Levett
c e n t s p e r k W h
Grid Supply Total Charges (2013)Other Metering Retail ServiceCarbon (environmental) STC (environmental) LGC (environmental)Network Ancillary Services (market) AEMO Fees (market)Electricity price (excl Carbon)
-
8/9/2019 Bill Components - Australia
26/28
Understanding your Electricity Bill
26
Network Tariff Optimisation
An analysis of the network tariff showed that on
current load assumptions, Levett would pay less
in total electricity costs by applying to SAPN for a
network tariff change request.
Based on the Monthly Business 2 tariff, the
annual network charges were approximately
$54,000.
Based on the Low Voltage Stepped Demand
tariff, at a power factor of 0.84, the annual
network charges would be approximately
$38,000.
If Levett annual load fell below 225,000 kWh (all
other things remaining the same), the Monthly
Business 2 tariff would be optimal.
Source: Solstice
Result
SAPN accepted the Levett change request and changed the Levett network tariff from June 2013.
The estimated annual savings based on FY2013 regulated network tariffs of moving from the Monthly Business 2
Tariff to the Low Voltage Stepped Demand Tariff is approximately $16,000 per year.
Source: Solstice
As the chart shows, there is a significant decline in the average Peak rate that applies to Levett following the changein network tariff, but a significant increase in the Off Peak rate. However, the overall average unit price declines by
17% from 25.7 cents per kWh to 22 cents per kWh representing a total annual saving of $16,000 (FY2013 excluding
GST) from an annual bill of $95,000 down to $79,000 per year.
$-
$5,000
$10,000
$15,000
$20,000
$25,000
$30,000
$35,000
$40,000
$45,000
$50,000
$55,000
$60,000
N e t w o r k C o s t s
kWh
Network Options - Levett
Network Total (Business 2 Rate) Network Total (Low Voltage Stepped Demand)
02468
1012
141618202224262830323436
Peak Off Peak Average Peak Off Peak Average
Levett (B2R Network Tariff) Levett (VLVS Network Tariff)
c e n t s p e r k W h
Grid Supply Total Charges (2013)Other Metering Retail Service
Carbon (environmental) STC (environmental) LGC (environmental)
Network Ancillary Services (market) AEMO Fees (market)
Electricity price (excl Carbon)
-
8/9/2019 Bill Components - Australia
27/28
Understanding your Electricity Bill
27
Case Study – Sonnex Engineering
Sonnex Engineering Pty Ltd provides precision plasma, laser & oxy profile cutting services to a diverse Australian
domestic customer base. Some of this cutting equipment is very energy usage intensive.
The Elizabeth South site typically operates an 8 hour shift, 5 days per week with approximately 32 full timeequivalent (FTE) personnel.
The following table summarises the Sonnex electricity consumption for the 12 months ending 30 April 2013.
Source: Solstice
Source: Solstice
Load Characteristics
The Sonnex load fluctuates throughout the year
with demand from the production schedule, and
includes a Christmas shutdown. Excluding
Christmas, the Sonnex maximum load ranged
from around 150kW to 300kW over the 12
month sample period.
Sonnex has a very low load factor of 20% (due to
its non shift operations) and consumes 75% of itsenergy at peak times, which drives up the
average cost of electricity. Half hourly load data
shows that Sonnex is at or above 145kW load
(50% of maximum load) for only about 17% of
the time, and uses the top 10% of its maximum
load for only about 0.05% of the time.
Price Characteristics
The Sonnex electricity rates were significantly
above its peers at March 2013, and the totalaverage rate and charging basis resembled what
one would ordinarily see for a small to medium
enterprise (SME) rather than an industrial
customer.
In addition, network costs, whilst charged as a
pass through at regulated rates appear relatively
high with Sonnex on a Quarterly Business 2 Rate
network tariff.
Financial Year 2013 total electricity expenditure
(excluding GST)
Total annual spend: $180,833
Average annual spend: $0.339/kWhSource: Solstice
Statistic Units Value Note
Electricity consumption kWh pa 519,151
Peak Electricity consumption kWh pa 390,053 75%
Off Peak Electricity consumption kWh pa 129,098 25%
Maximum demand kW 290 at 10:00 on Wed 12 Dec 2012
Minimum demand kW 10 at 05:00 on Sat 24 Nov 2012
Average demand kW 59
Load Factor % 20%
0
50
100
150
200
250
300
D
e m a n d ( k W )
Time of Day (Half Hour Ending)
Year - Work Day & Non Work Day Demand
Work Day Minimum Work Day Average Work Day MaximumNon Work Day Minimum Non Work Day Average Non Work Day Maximum
02468
101214161820222426283032343638404244
Peak Off Peak Average Sonnex
centsper kWh
Grid Supply Total Charges (2013) Other Metering Retail Service Carbon (environmental) STC (environmental) LGC (environmental) Network Ancillary Services (market) AEMO Fees (market) Electricity price (excl Carbon)
-
8/9/2019 Bill Components - Australia
28/28
Understanding your Electricity Bill
Network Tariff Optimisation
An analysis of the network tariff showed that on
current load assumptions, Sonnex would pay less
in total electricity costs by applying to SAPN for a
network tariff change request.
Based on the Quarterly Business 2 tariff, the
annual network charges were approx. $82,000.
Based on the Low Voltage Stepped Demand
tariff, at a power factor of 0.86, the annual
network charges would be approximately
$70,000.
However, if Sonnex annual load fell below
410,000 kWh (all other things remaining the
same), the Business 2 tariff would be optimal. Source: Solstice
Result
Sonnex took a 2 step approach to reducing its overall electricity costs in the second quarter of 2013.
Firstly, Sonnex negotiated reduced Peak and Off Peak electricity rates with its Retailer for a new contract
commencing in April 2013. The revised rates recognised Sonnex as a significant customer, and are expected to save
approximately $41,000 per year.
Secondly, Sonnex made a network change request application to SAPN to move from the Business 2 Tariff to the Low
Voltage Stepped Demand Tariff, which is expected to save a further $1,000/month or approx. $12,000 per year.
Source: Solstice
$-
$10,000
$20,000
$30,000
$40,000
$50,000
$60,000
$70,000
$80,000
$90,000
$100,000
N e t w o r k C o s t s
kWh
Network Options - Sonnex
Network Total (Business 2 Rate) Network Total (Low Voltage Stepped Demand)
02468
10121416182022242628303234363840
Retailer Invoice
Mar 2013
Retailer Contract
May 2013
Optimised Network
Jul 2013
c e n t s p e r k W h
Sonnex Grid Supply Total Charges (2013)Other Metering Retail Service
Carbon (environmental) STC (environmental) LGC (environmental)Network Ancillary Services (market) AEMO Fees (market)Electricity price (excl Carbon)
$180,833 $139,843 $127,145
$40,991$12,697
Tariff Savings
OptimisedNe twork
New Contract
Energy Rate Savings
top related