bill of quantities - · pdf filebill of quantities name of work : construction of...
Post on 18-Mar-2018
212 Views
Preview:
TRANSCRIPT
BILL OF QUANTITIES
Name of work : Construction of Institutional Block at Institute of Hotel Management,
Jagdishpur
SL. NO
SCH. P.W.D
Description of the work Quantit
y Unit
Rate in Rs.
Amount in Rs.
1 PWD
2015,
251
EXCAVATION in foundation in
ordinary Soil ( Loam clay or sand )
including lift upto 1.5m lead upto 30.0
m & including filling watering and
ramming of excavated earth into the
space between the building & sides of
foundation trenches or into the plinth
and removal & disposal surplus earth
as directed by the engineer I/C within
a lead of 30 m.from foundation
trenches.
6048.15 Cum 90.25 545845.21
2 U.P.P.A.
R 2015
Providing and injecting chemical
emulsion for preconstructional
antitermite treatment and creating a
chemical barrier under and alround
the coloumn pitswall tench basement
excavation top surface if plinth filling
junction of wall and floor along the
external perimer of binding expansion
joints, surrounding of pipes and
conduits etc.complete(plinth area of
the building at ground floor only shall
be measured as per I.S.6313(Part ll
1981) aldrine emulsifiable concrete or
any other approved material such as
hepthachlor or chlordance will be
used.The rate of application of
chemical emulsion shall be as
follows:- (1) treatment for masonary
& foundation 5 litres per sq.m. (2)
back fill in immediate contract with
foundation 7.5 litre per sq.m
(3)treatment of top surface of plinth
filling 5 liters per sq.m. (4)
treatment of soil along external
parameter of building 7.50 lire per
sq.m.
4709.75 Sqm 237.50 1118566.72
3 PWD
2015,
255+
SAND
RATE
Sand filling in plinth including
supply of necessary quantity of sand
including watering, dressing etc.
labour & T &P etc. required for
proper completion of work saplings
of girth upto 30 ground level and
removal of rubbish upto a distsnce of
50m out side the periphery of area
cleared. under floor fine sand.
475.24 Cum 634.60 301589.75
4 PWD
2015,
281
Providing and laying Cement
concrete 1:4:8 (1cement :4 coarse
sand :8 graded stone ballast 20 mm.
nominal size) including supply of all
materials, labour and T&P etc.
required for proper completion of the
work and curing complete, also
including cost of formwork in
foundation.
840.09 Cum 4864.00 4086181.84
5 PWD 2015, 282
Cast cement concrete door sills, chaukhats, boundary posts shelves and similar small work with cement approved coarse sand and 2 cm gauge stone grit in proportions of 1:2:4 excluding its fixing and binding the same with 24 B.W. G.G.I. binding wire, moulds, all materials labour, Tools & Plants etc. required for proper completion of the work. the rate excludes making of drip course which shall be paid extra.
1.82 Cum 7172.50 13041.06
6 PWD 2015, 283
R.c.c.work with cement approved coarse sand and 2 cm. (3/4") guage approved stone ballast in the proportion 1:6, (1cement :6 aggregate) in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 B WG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200.
316.92 Cum 7446.1 2359845.76
(i) Analysis rate As in item 283 above but for slabs 1223.03 Cum 7731.1 9455373.39
(ii) Analysis rate
As in item 283 above but for lighter beams
109.27 Cum 7921.1 865566.33
(iii) Analysis rate
As in item 283 above but for heavier beams
993.21 Cum 8111.1 8055988.64
(iv) Analysis rate
As in item 283 but on R.C.C.coiumns in 1:1.5:3
298.06 Cum 8208 2446435.99
7 PWD
2015,
255
Filling of available excavated earth in trenches, plinth, sides of foundation
etc. inlayers not exceeding 20 cms in
depth, consolidating each deposited
layer by ramming and watering
including lead upto 50m & lift upto
1.50m.
4135.19 Cum 64.60 267133.44
8 Analysis rate
P/F of Earth inner side in building 2376.22 Cum 368.60 875874.44
9 PWD
2015,
303+
307-306
Class-150 brick work in 1:6 cement
and COARSE sand mortar in
foundation and plinth including
supply of all materials, labour tools
and plants, etc. Required for proper
completetion of the work.
755.94 Cum 4963.75 3752313.56
10 Analysis rate
Sand pilling 2843.00 Nos 237.50 675212.50
11 PWD
2015,
303+307
-306+
309 +310
Class-150 brick work in 1:6 cement
and COARSE sand mortar in
SUPERSTRUCTURE including
supply of all materials, labour tools
and plants, etc. Required for proper
completetion of the work
649.04 Cum 5372.25 3486795.75
12 PWD
2015,
305b+31
0+ 310a
Class-150 reinforced HALF brick
work in 1:4 cement and COARSE
sand mortar in
SUPERSTRUCTURE including
supply of all materials, labour tools
and plants, etc.
412.47 Cum 5448.25 2247233.07
13 PWD
2015,
504
Mild steel or iron in plain work
such as in reinforced concreted or
reinforced brick work (when not
included in overall rates) wrought to
required shape as necessary including
bending for proper completion of the
work and including supply of steel its
wastage. Bend hooks and authorized
overlapping shall be measured.
6242.18 Qtl 6545.50 40858190.20
14 DSR 2015, 6.15
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
3586.69 Sqm 66.03 236810.88
15 PWD 2015, 586
12 mm thick plaster with cement mortar in proportion of 1:6 cement & fine sand of not less than 1.25 F.M. for all floors.(in inner wall)
7206.20 Sqm 103.55 746202.22
16 PWD 2015,
583+587
Ceiling plaster cement & course sand in F.M not less than 1.25, 1:3 including chiping of RCC surface before ceiling plaster. The cost of including all materials, labour, T & P and scafolding etc. complete
6677.57 Sqm 158.65 1059395.94
17 PWD 2015, 586
12 mm thick plaster with cement mortar in proportion of 1:6 cement & fine sand of not less than 1.25 F.M. for all floors.(in outer wall)
2772.60 Sqm 103.55 287102.94
18 DSR 2014,
13.73.1
Forming groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer,including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge :Forming groove of uniform size in the top layer of washed stone grit plaster
7587.35 Rmt 30.02 227772.25
19 DSR
2014,
8.12
Providing and laying flamed finish
Granite stone flooring in required
design and patterns, in linear as well
as curvilinear portions of the building
all complete as per the architectural
drawings with 18 mm thick stone slab
over 20 mm (average) thick base of
cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with
cement slurry and pointing with white
cement slurry admixed with pigment
of matching shade including rubbing,
curing and polishing etc. all complete
as specified and as directed by the
Engineerin- Charge :
3024.44 Sqm 3082.13 9321738.76
20 Analysis of rate
Granite stone slab 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete.
359.23 Sqm 2508.00 900960.01
21 DSR Item no. 8.3.2
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
295.23 Rmt 219.02 64662.01
22 DSR
2014,
11.39
Providing and laying rectified Glazed
Ceramic floor tiles of size 300x300
mm or more (thickness to be specified
by the manufacturer), of 1st quality
conforming to IS : 15622, of approved
make, in colours White, Ivory, Grey,
Fume Red Brown, laid on 20 mm
thick cement mortar 1:4 (1 Cement: 4
Coarse sand), including grouting the
joints with white cement and
matching pigments etc., complete.
384.77 Sqm 902.55 347270.03
23 DSR
2014,
11.36
Providing and fixing Ist quality
ceramic glazed wall tiles conforming
to IS: 15622 (thickness to be specified
by the manufacturer), of approved
make, in all colours, shades except
burgundy, bottle green, black of any
size as approved by Engineer-in-
Charge, in skirting, risers of steps and
dados, over 12 mm thick bed of
cement mortar 1:3 (1 cement : 3
coarse sand) and jointing with grey
cement slurry @ 3.3kg per sqm,
including pointing in white cement
mixed with pigment of matching
shade complete.
2684.46 Sqm 794.82 2133655.79
24 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
DSR Item no.
11.26.1 25mm thick 2673.52 Sqm 1084.33 1204321.95
25 DSR Item no. 11.27
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete
712.11 Sqm 1131.69 805881.56
26 DSR 2014,
11.47.2
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints tobe made parately).
1072.02 Sqm 1548.69 1660230.48
27 DSR Item no.
8.2.2.2
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm
31.79 Sqm 3712.03 117995.78
28 DSR Item no. 8.3.2
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work
53.26 Rmt 219.02 11666.01
29 DSR
2014,
13.80
Providing and applying white cement
based putty of average thickness 1
mm, of approved brand and
manufacturer, over the plastered wall
surface to prepare the surface even
and smooth complete.
16656.37
Sqm 85.17 1418581.44
30 DSR
2014,
13.60.1
Wall painting with acrylic emulsion
paint of approved brand and
manufacture to give an even shade :
Two or more coats on new work
7206.20 Sqm 76.48 551094.30
31 DSR
2014,
13.45.1
Finishing walls with textured
exterior paint of required shade New
work (Two or more coats applied @
3.28 ltr/10 sqm) over and including
priming coat of exterior primer
applied @ 2.20kg/10 sqm texture of
minimum film thickness 1.0 mm.
2772.60 Sqm 139.13 385745.19
32 DSR
2014,
13.68.1
French spirit polishing : Two or
more coats on new works including a
coat of wood filler
793.70 Sqm 184.25 146241.21
33 DSR 2014, 5.30
Making drip course in sun shade or FACIA as per direction of engineer - in - charge including supply of all materials labour etc .required for proper completion of the work.
63.45 Rmt 29.21 1853.53
34 DSR
2014,
22.7.1
Providing and laying integral cement
based water proofing treatment
including preparation of surface as
required for treatment of roofs,
balconies, terraces etc consisting of
following operations: a) Applying a
slurry coat of neat cement using 2.75
kg/sqm of cement admixed with water
proofing compound conforming to IS.
2645 and approved by Engineer-in-
charge over the RCC slab including
adjoining walls upto 300 mm height
including cleaning the surface before
treatment. b) Laying brick bats with
mortar using roken bricks/brick bats
25 mm to 115 mm size with 50% of
cement mortar 1:5 (1 cement : 5
coarse sand) admixed with water
proofing compound conforming to IS
: 2645 and pproved by Engineer-in-
charge over 20 mm thick layer of
cement mortar of mix 1:5 (1 cement
:5 coarse sand ) admixed with water
proofing compound conforming to IS
: 2645 and approved by Engineer-in-
charge to required slope and treating
similarly the adjoining walls upto 300
mm height including rounding of
junctions of walls and slabs c) After
two days of proper curing applying a
second coat of cement slurry using
2.75 kg/ sqm of cement admixed
jointless cement mortar of mix 1:4 (1
cement :4 coarse sand) admixed with
water proofing compound conforming
to IS : 2645 and approved by
Engineer-in-charge
4595.61 Sqm 968.10 4448995.84
35 Grading roof for water proofing treatment with
DSR 2014,
22.14.2
Cement mortar 1:3 (1 cement : 3 coarse sand) 229.78 Cum 8745.42 2009524.61
36 DSR 2014,
12.21.1
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1 In 75x75 mm deep chase
247.67 Rmt 135.95 33669.50
37 DSR 2014, 12.22
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
22.00 Nos 177.32 3900.99
38 PWD 600 40mm thick water proofing plaster in two layers
74.30 Sqm 522.50 38822.27
39 DSR 2014, 22.3
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry@4.4kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement :3coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
214.22 Sqm 496.76 106414.90
40 Analysis rate
Providing & laying of light cinder filling under floor of toilets & other sunken roofs .
96.40 Cum 1731.85 166948.68
41 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).
DSR Item no. 9.1.1 Second class teak wood 6.45 Cum
86922.06
560544.03
42 DSR
2014,
9.20.1+
9.127.2
Providing and fixing ISI marked flush
door shutters conforming to IS :
2202 (Part I) decorative type, core of
block board construction with frame
of 1st class hard wood and with
decorative both side high pressure
laminated sheet of plain / wood grain
in gloss / matt / suede finish with high
density protective surface layer and
reverse side of adhesive bonding
quality conforming to IS : 2046 Type
S, including cost of adhesive of
approved quality of 1.0 mm thick
including 32x5 mm teak wood lipping
on edges of shutters.
274.47 Sqm 3118.71 855991.65
43 DSR Item no. 9.53
Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand: 6 graded stone aggregate 20mm nominal size).
1040.00 Nos 111.48 115941.80
44 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
a) DSR Item no.
9.97.2 250x10 mm 142.00 Nos 90.49 12849.23
b) DSR Item no.
9.97.4 150x10 mm 36.00 Nos 62.08 2234.97
45
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
DSR Item no.
9.100.1 125mm 356.00 Nos 66.31 23606.36
46 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
a) DSR Item no.
9.101.2 Twin rubber stopper 178.00 Nos 79.75 14195.95
47 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge
a) DSR Item no.
10.27.2 10x80mm 90.00 Nos 67.21 6049.13
b) DSR Item no.
10.27.3 10x120mm 108.00 Nos 82.41 8900.55
48 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.
brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
DSR Item no.
21.1.1.2
Powder coated aluminium (minimum thickness of powder coating 50 micron)
3674.84 Kg 358.86 1318761.60
49 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
DSR Item no.
21.1.2.2
Powder coated aluminium (minimum thickness of powder coating 50 micron)
839.16 Kg 413.96 347380.77
50 Providing and fixing glazing in alu. door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):
DSR Item no.
21.3.2
With float glass panes of 5.50 mm thickness
209.99 Sqm 787.31 165328.34
51 Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.
DSR Item no.
21.8.1 Upto 5mm depth and 5mm width 289.57 Rmt 84.31 24414.37
52 Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.
DSR Item no.
21.15.2
Powder coated minimum thickness 50 micron aluminium
96.00 Nos 52.39 5029.68
53 Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineerin- charge
DSR Item no.
21.16.2
Powder coated minimum thickness 50 micron aluminium
96.00 Nos 68.97 6621.12
54 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade
DSR Item no. 13.61
Two or more coats on new work 247.70 Sqm 70.68 17507.44
55 DSR 2014,
10.30.1
Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with : 4.0 mm thick glass panesFixing of Glass Pan 4mm thick
247.70 Sqm 726.23 179886.55
56 DSR 2014, 10.28
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)S.S.Railing.900MM HT each rmt=10.00 kg
1671.08 Kg 588.43 983313.60
57 DSR
2014,
14.28.2
Providing and fixing curtain rods of
1.25 mm thick brass plates with two
brass brackets fixed with brass screws
and wooden plugs etc. wherever
necessary complete. 25 mm diameter.
249.54 Rmt 223.35 55732.39
58 DSR 2014, 14.72
Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc.
1947.48 Sqm 151.91 295832.56
59 DSR
2014,
9. 134
.1.1.1
Providing and fixing wire gauge
shutters using stainless steel grade
304 wire gauge with wire of dia 0.5
mm and average width of aperture 1.4
mm in both directions for doors,
windows and clerestory windows with
necessary screws : 35 mm thick
shutters with ISI marked Stainless
Steel butt hinges with necessary
screws of required size Second class
teak wood
288.48 Sqm 3327.66 959963.36
60 DSR 2014,
18.27.3
Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536
150mm 231.00 Rmt 1535.91 354795.79
61 DSR 2014,
17.57.1.2
Providing and fixing collar : 60.00 Nos 302.43 18145.95
62 DSR 2014,
17.37.1
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :
150.00 Nos 145.26 21788.25
63 DSR 2014,
17.39.1.2
Providing and fixing plain bend of required degree. 30.00 Nos 318.96 9568.88
64 DSR 2014,
17.50.1.2
Providing and fixing single equal plain invert branch of required degree : 30.00 Nos 495.52 14865.60
65 DSR 2014,
17.55.1.2
Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete :
30.00 Nos 487.78 14633.33
66 DSR
2014,
12.39.2
Providing lead caulked joints to sand
cast iron rain water pipes and fittings:
150 mm dia Pipe 240.00 Nos 363.47 87232.80
67 DSR 2014, 12.44
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams
30.00 Nos 39.05 1171.35
68 DSR 2014,
13.56.2
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. 150 mm diameter pipes
231.00 Rmt 54.72 12640.32
69 DSR 2014, 5.46.1
Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the correspondingaluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV,airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. Material shall confirm to ASTM 6063. Roof Joint of 100 mm gap
162.47 Rmt 6040.62 981419.94
70 Providing & fixing of Tata blue scope
Sheet for OPEN TO SKY Covering
including nut & bolts washer etc all
complete of direction of engineer in
charge.
608.69 Sqm 1425.00 867389.38
71 Analysis of rate
Rebaring Work 6612.00 Nos 185.25 1224873.00
72 Analysis rate
Drains with Grating 253.05 Rmt 3658.45 925770.77
73 Analysis rate
P/L of P.O.P. with Polythin sheet 9786.11 Sqm 294.50 2882009.54
74 Analysis of rate
Apron 252.92 Sqm 2666.65 674449.12
75 Analysis of rate
Apron Drain 259.22 Rmt 3658.45 948343.41
76 DSR 2015, 5.45.1
Providing and fixing of expansion joint system related with wall joint (internal/external location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning /centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides anExpansion Joints System suitablefor vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063.) Wall Joint of 100 mm gap
33.60 Rmt 4826.86 162182.33
77 C.P.A.R Overhead Tank IN Terrace 150000 Ltr 14.25 2137500.00
GRAND TOTAL 127147511.92
Name of work : Construction of Institutional Block at Institute of Hotel Management, Jagdishpur
PLUMBING WORK
Sl.No. SANITARY FIXTURES & ACCESSORIES QTY UNIT RATE AMOUNT
1 17.3.1 Providing & fixing white vitreous china pedastal type water
closet (European type) with ISI marked white solid plastic
seat and lid, 10 litre white vitreous china low level
flushing cistren & C.P. flush bend with fittings and CI
brackets, 40 mm flush bend, over flow arrangement with
specials of standard make and mosquito proof coupling of
approved municipal design complete including painting of
fittings and brackets, cutting and making good the walls
and floors wherever required. 24.00 Nos
4,545.37 109,088.88
2 17.20.1 P.V.C.Cover 24.00 Nos 390.45 9,370.80
3
17.18.1
P.V.C.Sistern low-level
48.00 Nos
821.80 39,446.28
4
Providing white viterous china Under counter Oval Wash
Basin size 550 x 450 mm with C.P. brass one hole basin
mixer, CI/MS brackets, 32 mm C.P. brass waste of
standard pattern, standard quality P.V.C. waste pipe.
(Parryware C0418 & Jaquar 167 or equivalent) 26.00 Nos
3,211.00 83,486.00
5 17.8 Providing and fixing white vitreous china pedestal for wash
basin completely recessed at the back for the reception of
pipes and fittings. 26.00 Nos
930.95 24,204.77
6
17.32.1
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia
26.00 Nos
839.90 21,837.27
7
Providing and fixing flexible P.V.C. waste pipe for sink or
wash basin including PVC waste fittings complete.
17.28.2.1
32 mm dia (for wash basin)
43.00 Nos
70.73 3,041.28
17.28.2.2
40 mm dia (for sink )
24.00 Nos
72.91 1,749.90
8
17.31
Providing & Fixing 600 X 450 mm bevelled edge mirror
of superior glass (of approved quality) complete with 6mm
thick hard board ground fixed to wooden cleats with C.P.
brass screws and washers complete. 26.00 Nos
754.25 19,610.57
9
17.34.1
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. each 543.80 26.00 Nos
516.61 13,431.86
10
17.34
Providing and fixing toilet paper holder : C.P. brass 24.00 Nos
395.11 9,482.52
11
Providing & fixing stainless steel AISI 304 (18/8) kitchen
sink with drain board as per IS :13983 with C.I. brackets
and stainless steel plug 40 mm including painting of
fittings and brackets cutting and making good the walls
wherever required.
17.10.2.2
600x450mm bowl depth 200 mm
24.00 Nos
3,789.74 382963.2
12 17.69.2 Waste coupling 38 mm dia of 83 mm length and 77mm breadth,
weighing not less than 60 gms 56 Nos 136.94 382963.2
SOIL , WASTE, VENT AND RAIN WATER PIPES
AND FITTINGS (Centrifugally Cast Spun Iron)
13
The following items include providing, fixing and testing in
position of ISI marked (IS : 3989) centrifugally cast spun
iron soil, waste, vent and rain water pipes and fittings
cut to required lengths, fixing at wall, ceiling or on floor
including connections to all required fittings complete in all
respects.
Providing & fixing pipes.
17.35.1.2
100mm dia Centrifugally cast (spun) iron S & S Pipe
1534.50 R.M.
871.86 1,337,873.01
M.R 150mm
511.50 R.M.
1,263.24 646,149.05
17.35.2.2
75mm dia Centrifugally cast (spun) iron S & S Pipe
191.81 R.M.
751.74 144,192.17
14
Painting sand cast iron/ centrifugally cast (spun) iron soil,
waste vent pipes
and fittings with two coats of synthetic enamel paint of any
colour such as
chocolate grey, or buff etc. over a coat of primer (of
approved quality) for
ew work :
17.65.1
100 mm diameter pipe
1534.50 R.M.
36.72 56,343.00
17.65.2 75 mm diameter pipe 191.81 R.M.
28.03 5,375.55
M.R
150 mm diameter pipe 511.50 R.M.
45.55 23,300.10
15
Providing lead Caulked joints to sand cast
iron/centrifugally cast (spun) iron pipes & fittings of
diameters.
17.58.1 100 mm 1023.00
Nos
231.56 236,888.44
M.R 150mm 341.00
Nos
405.23 138,184.11
17.58.2 75 mm 127.88
Nos
195.04 24,940.10
16
Providing & fixing M. S. holder - bat clamps of approved
design to sand Cast iron/cast iron (spun) pipe embedded in
& including cement concrete blocks 10*10*10cm of 1:2:4
mix (1 cement : 2 coarse sand : 4 graded stone aggregate
20 mm nominal size). Including cost of cutting
holes&making good the walls etc.
17.37.1
For 100 mm dia pipe
1023.00 Nos
145.26 148,595.87
17.37.
For 150 mm dia pipe
341.00 Nos
143.07 48,786.87
17
Providing & fixing sand cast iron S&S trap of self cleaning
design with sand cast iron screwed down or hinged grating
with or without vent arm complete, including cost of
cutting & making good the walls and floors.
17.60.2.1
100 mm inlet & 75 mm outlet
100.00 Nos
969.86 96,985.50
17.60.1.1
100mm inlet & 100mm outlet
400.00 Nos
933.42 373,369.00
18
Providing & fixing Sand Cast iron S & S coller
17.57.1.2
100 mm dia
512 Nos
302.43 154,694.22
17.57.2.2
75 mm dia
171 Nos
208.76 35,594.01
19
Providing & fixing plain sand cast iron S & S Bend of
required degree.
17.39.1.2
100 mm dia
92.00 Nos
318.96 29,344.55
M.R
150mm dia
92.00 Nos
498.75 45,885.00
20
Providing & fixing single equal plain sand cast iron S&S
junction of required degree with access door, insertion
rubber washer 3 mm thick bolts & nuts complete. (door tee)
17.43.1.2
100 * 100 * 100 mm
160.00 Nos
592.61 94,817.60
M.R
150*100 mm
500.00 Nos
1,087.87 543,936.75
21
17.47.1.2
Providing & fixing single unequal 100*100*75 mm sand
cast iron S & S junction of required degree with access
door,insertion rubber washers 3mm thick, bolts&nuts
complete.
160.00 Nos
752.59 120,414.40
22
Providing & fixing of door piece
M.R
150 mm dia
84.00 Nos
412.78 34,673.10
17.55.1.2
100 mm dia
48.00 Nos
487.78 23,413.32
23
P/f terminal guard
17.56.1
100mm
24.00 Nos
412.78 9,906.60
M.R
150mm
60.00 Nos
542.82 32,569.23
24
Providing and fixing single unequal plain invert branch of
required degree :
17.52.1.2 Sand cast iron S&S as per IS - 3989
92.00 Nos
627.90 57,767.03
25
Providing and fixing sand cast iron S&S off sets as per IS: 3989 :
17.54.1.1 With 75 mm dia pipe 25.00 Nos
269.47 6,736.69
17.54.2.1 150 mm off sets With 75 mm dia pipe 35.00 Nos
346.13 12,114.64
17.54.2.2
With 100 mm dia pipe
30.00 Nos
461.99 13,859.55
WATER SUPPLY PIPES AND FITTINGS
26
Providing, fixing G. I. pipes complete with G. I. fittings
and clamps including cutting and making good the walls
etc. (internal work) - (Exposed on wall) -
18.11.1
15mm dia nominal bore
700.00 R.M.
290.75 203,523.25
18.11.2
20mm dia nominal bore
75.00 R.M.
317.16 23,786.81
18.10.3
25mm dia nominal bore
100.00 R.M.
288.94 28,894.25
18.10.4
32mm dia nominal bore
50.00 R.M.
326.04 16,302.00
18.10.5
40mm dia nominal bore
125.00 R.M.
404.37 50,545.94
18.10.6
50mm dia nominal bore
150.00 R.M.
500.84 75,126.00
27
Painting G. I. pipes and fittings with synthetic enamel
white paint over a ready mixed priming coat, both of
approved quality for new work.
18.38.1
15mm dia nominal bore
700.00 R.M.
9.12 6,384.00
18.38.2
20mm dia nominal bore
75.00 R.M.
10.78 808.69
18.38.3
25mm dia nominal bore
100.00 R.M.
14.20 1,420.25
18.38.4
32mm dia nominal bore
50.00 R.M.
16.82 840.75
18.10.5
40mm dia nominal bore
125.00 R.M.
404.37 50,545.94
18.38.6
50mm dia nominal bore
150.00 R.M.
23.51 3,526.88
28 P/F G.I.Union in G..Pipe
18.46.2
20mm
150.00 NOS.
179.08 26,861.25
18.46.3
25mm
135.00 NOS.
190.10 25,662.83
18.46.4
32mm
45.00 NOS.
228.71 10,292.06
18.46.6
50mm
105.00 NOS.
372.78 39,141.90
18.46.7
65mm
30.00 NOS.
604.49 18,134.55
18.46.8
80mm
27.00 NOS.
692.79 18,705.26
29
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
18.13.1
25to 40 mm nominal bore each 367.75
450.00 NOS
349.36 157,213.13
18.13.2
50 to 80 mm nominal bore each 761.10
100.00 NOS
723.05 72,304.50
30
Cutting holes up to 30x30 cm in walls including making good the same:
18.76.1
With common burnt clay F.P.S. (non modular) bricks 150.00 NOS
197.55 29,632.88
31
18.77
Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm
80.00 NOS 183.35 14,668.00
nominal size), including finishing complete so as to make it leak proof.
32
Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.
18.62.2
20 mm nominal bore, 120 mm long, weighing not less than 198gms
10.00 NOS
271.32 2,713.20
18.62.3
25 mm nominal bore, 152mm long, weighing not less than 440 gms
15.00 NOS
526.78 7,901.63
18.62.4
40 mm nominal bore, 206mm long, weighing not less than 690 gms
10.00 NOS
957.08 9,570.78
18.62.5
50 mm nominal bore, 242mm long, weighing not less than 1240 gms
10.00 NOS
1,332.28 13,322.80
SUPPLY OF SANITARY FIXTURES,
ACCESSORIES AND BATHROOM FITTINGS
33
C.P.Pillar Cock for wash basin
24.00 Nos
3,211.00 77,064.00
34
Providing white vitreous China recessed soap tray (210
mm X 110 mm) (Parryware C9935 or equivalent) 43.00 Nos
223.25 9,599.75
35
Providing 600 mm long C. P. brass towel rail complete
with C.P. brass brackets . (Jaquar 1111 or equivalent) 29.00 Nos
926.25 26,861.25
36
Providing ISI Marked CP brass angle valve 15mm. with
flange of approved quality (Jaquar 053 or equivalent) 134.00 Nos.
470.25 63,013.50
37
C.P.Soap Dish
43.00 Nos
223.25 9,599.75
38
C.P.Ring
29.00 Nos
660.25 19,147.25
39
18.51
P/F C.P.Bib cock long body
16.00 Nos
580.12 9,281.88
40
18.49
P/F C.P.Bib cock short body
16.00 Nos
436.53 6,984.40
41
M.R.
P/F C.P.Waste coupling
26.00 Nos
281.58 7,321.08
42
P/F C.P.Extention Piece
M.R.
15x25mm
166.00 Nos
56.32 9,348.46
M.R.
15x50mm
55.00 Nos
103.10 5,670.69
43
18.101.1
P/F C.P.Flunch
166.00 Nos
49.64 8,239.83
44
M.R.
P/F C.P.Floor Jali
30.00 Nos
47.65 1,429.56
45
17.28.1.1
P/F P.V.C.Waste Pipe 32mm
67.00 Nos
72.91 4,885.14
46
18.21.2.1
Providing & fixing 15 mm nominal bore 45 cm long
unplasticised PVC connection pipe with brass unions. 67.00 Nos
65.17 4,366.39
FIXING OF SANITARY FIXTURES,
ACCESSORIES AND BATHROOM FITTINGS
47 Fixing of china soap tray recess type
43.00 Nos
190.00 8,170.00
48 Fixing of C. P. brass towel rail
29.00 Nos
71.25 2,066.25
49 Fixing of CP brass angle valve
134.00 Nos.
57.00 7,638.00
50
Fixing of CP brass single hole wash basin mixture in
place of pillar cock. 26.00 Nos.
142.50 3,705.00
51 Fixing of CP brass single hole wash basin pillar cock. 26.00
Nos.
142.50 3,705.00
WATER SUPPLY PIPES AND FITTINGS
52
Providing, fixing and testing in position ISI marked (IS :
1239) G.I pipes (medium class) manufactured from
seamless pipes, in concealed or exposed works complete
with all necessary G.I fittings i.e. sockets, elbows, tees,
bends, unions, plugs and clamps including cutting chases
and making good the walls (on terrace the pipes shall be
supported at suitable interval and inside ducts these shall be
properly clamped through duct walls). The Galvanization
shall conform to IS : 4736. The work shall include the
painting with two coats of anti-corrosive paints on buried
and concealed pipe works and with two coats enamel paint
of approved quality and shade over a coat of primer on
exposed pipe works complete as required by the Engg-in-
charge for proper completion of the work.
(Make : Jindal(Hissar) / Bharat / Prakash Surya)
65mm nominal bore (wall thickness - 3.6 mm) 300.00
R.M.
522.50 156,750.00
80mm nominal bore (wall thickness - 4.0 mm) 200.00
R.M.
684.00 136,800.00
100mm nominal bore (wall thickness - 4.5 mm) 150.00
R.M.
931.00 139,650.00
49
Providing & fixing of hand lever operated forged brass
body full way ball valve type isolating valve having
forged brass hard chrome plated mirror finish ball, steel
handle with PVC grip, teflon seat, screwed ends tested to a
pressure of 15 kg/sqcm complete. (Make : CIM / Audco /
Festo / Zoloto / Advance)
15 mm nominal bore 96.00
Nos.
427.50 41,040.00
20 mm nominal bore 111.00
Nos.
579.50 64,324.50
25 mm nominal bore 75.00
Nos.
845.50 63,412.50
32 mm nominal bore 75.00
Nos.
1,372.75 102,956.25
40 mm nominal bore
36.00 Nos.
1,885.75 67,887.00
53
Providing and fixing in position vent connection to water
storage tanks comprising two elbows of 50 mm dia. And
mosquito proof brass wire mesh fixing in frame and welded
to upstand pipe complete as required. (Length of pipe
involved shall be measured seperately under item piping).
24.00 nos.
275.50 6,612.00
54
Providing and fixing of cast iron Manhole Cover with
frame for overhead / underground water storage tanks. The
fixing of frame shall be done during the casting of the RCC
slab of the tank.
600 x 600 mm (38 Kg)
100.00 Nos.
2,436.75 243,675.00
55
18.33 Making main Hole 600*600 mm
100.00 Nos.
6,416.59 641,658.50
Total 8123328.27
top related