c1sl36 install guide - coyote; outdoor · c1sl36 install guide 10 1/4" opening height doors /...
Post on 20-Jul-2020
5 Views
Preview:
TRANSCRIPT
www.coyoteoutdoor.com
DIMENSIONAL RENDERINGS
Model No. Gas Supply BTU's Regulator WC Pressure Max PSI Electrical RequirementsC1SL36LP Propane 90,000
1/2" Female Pipe11" .5 PSI Qty 1 - 120 VAC 60 Hz Grounded Plug
C1SL36NG Natural Gas 90,00020 lb Tank Regulator
4" .5 PSI Qty 1 - 120 VAC 60 Hz Grounded Plug
Model No. Height Width DepthModel No. Height Width Depth
C1SL36C1SL36 23"
CJAKTCS36 11"CJAKTCS36 23"
Cutout Dimensions for IslandOverall Product Dimensions
When using a Coyote insulated jacket, you will want to build your island to the jackets Cutout and Overall Dimensionslisted above (detailed on 2nd page). Once the jacket is installed, the grill will rest on/inside the insulated jacket
35 3/4"
20 1/2"25 1/2" 10 1/4"
11" 37 5/8" 22 1/8"
32 1/2"35 1/2"
C1SL36 INSTALL GUIDE
Important Note to Installer This file is not intended to replace your Owners' Manual which contains specific safety requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built in grill.
35 3/4"
20 1 /2"
10 1/4"
22 1 /8"
32 1/2"
23"
11"
37 5/8"
11"
23"
25 1/2"
35 1 /2"
www.coyoteoutdoor.com
C1SL36 INSTALL GUIDE
10 1/4"OPENINGHEIGHT
DOORS / DRAWERS OPENING WIDTH
20 1/2"OPENING
DEPTH
OPENINGHEIGHT
GRILLOPENING
GRILLOVERHANG
TOP VIEW
OPENING WIDTH
2 1/2"
OPENINGHEIGHT
DOORS / DRAWERS OPENING WIDTH
OPENINGDEPTH
OPENINGHEIGHT
24"
LINEROPENING
7/8"
JACKETOVERHANG
TOP VIEW
OPENING WIDTH
24"
FRONT VIEW FRONT VIEW
1 1/2" MININCLUDING COUNTERTOP
Combustible material can not be within 24" of the grills frame This applies to all directions - horizontal & vertical Shaded area above on "TOP VIEW" illustrates the 24" minimum
requirement (not to scale for rendering purposes) The grill is designed to hang from the counter top with no support
underneath Minimum rear clearance for the hood to open is 2" If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
24"
If using combustible material within 24" of the grill frame, you MUST usethe corresponding Coyote Insulated Jacket
Using a insulated jacket, does not waive any other standard installationprocedure (ventilation, connections, etc)
The jacket is designed to hang from the counter top with no supportunderneath
Minimum clearance for hood to open is 2" If you have a wall/partition behind the grill, the minimum rear clearance
to that wall should be at least 7" to allow for ventilation of the exhaust
Ventilation Requirements: Regardless if you are using a combustible or non-combustible building material, you must include at least two vents within
the island. These vents must be at least 20 sq. in. each and allow fresh air to move from the grill cabinet to the exterior environment. For a propane setup, the vents should be installed lower as propane is heavier than air. For a natural gas setup, the vents should be located higher in the island, as natural gas is lighter than air. Do not locate the two vents on the same wall of the island. Cross ventilation is key to allow any excess heat or trapped
gas to dissipate.
1 1/2"
1 5/8"
1 1/2"22 1/8"
1 1/2" MIN
7/8"
11"
INCLUDING COUNTERTOP
35 3/4"
1 3/4"
2 1/2"
21/2"
2"
G
GASCONNECTION
G
4 1/8"
4 1/8" G
GASCONNECTION
4 1/8"
G2 3/4"
32 1/2"
Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safetyrequirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill.
NON-COMBUSTIBLE CONSTRUCTIONInsulated Jacket NOT Required
COMBUSTIBLE CONSTRUCTIONInsulated Jacket Required - Model # CJAKTCS36
top related