cdt 30 mk iii mobile dehumidifier - dantherm
Post on 02-Mar-2022
4 Views
Preview:
TRANSCRIPT
01.2
0
dantherm.com
CDT 30 MK III
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 30 MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
CDT 30 MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
01.2
0
dantherm.com
Specific energy consumption (SEC)• 0.53 kWh/l at 30°C & 80% RH• 0.85 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassette(see separate data sheet)
Also available in this seriesCDT 30S MK IIICDT 40 MK IIICDT 40S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)
Model CDT 30 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 15.1 l/dDehumidification – 30°C & 80% RH 31.9 l/dAir volume 250 m³/hPower supply 230 V/50 HzMax. ampere consumption 3.6 AMax. power consumption 0.8 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 56 dB(A)Water container capacity 7 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 31 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
Sheetmetal flatstate is based on Dantherm A/S process equipment and is only entended as a guide.
AND WILL BE PROTECTED BY PATENTS
table LZT 142 0001, category
ohr
03-01-2012
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
65610.26g
SCALE: NOT TO SCALE
351 189
351189
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO
8Surface appearance according to reference BEND RADII:
ARE THE PROPERTY OF SAID COMPANY
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
REV.:
RE
V.:
CDT 30 MK II
CDT 30 MK II
PA
RT
NO
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
650
506
427
All dimensions are in mm.
736
650
426
0
5
10
15
20
25
30
35
40
0,00 0,20 0,40 0,60 0,80 1,00 1,20 1,40 1,60
°C
L/H
40% 60% 80%
01.2
0
dantherm.com
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels• On the back two Ø100 mm flex. air ducts may be connected
(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan
Water container• Water container with handles• Automatic stop when water container is full or removed• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 30S MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
CDT 30S MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 30S MK III
01.2
0
dantherm.com
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
CDT 30 S MK II
CDT 30 S MK IISCALE: NOT TO SCALE
64278.09g
BEND RADII:
24-05-2012
ohr
351190
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
351 190
only entended as a guide.
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
750
650
506
426
736
650
Specific energy consumption (SEC)• 0.51 kWh/l at 30°C & 80% RH• 0.86 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)
Also available in this series:CDT 30 MK IIICDT 40 MK IIICDT 40S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)
Model CDT 30S MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 14.4 l/dDehumidification – 30°C & 80% RH 34.4 l/dAir volume 350 m³/h*Power supply 230 V/50 HzMax. ampere consumption 7.9 AMax. power consumption with heating element 1.8 kWMax. power consumption without heating element 0.8 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 56 dB(A)**Water container capacity 7 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 33 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
All dimensions are in mm.
*Measured without air ducts mounted.**Measured with air ducts mounted.
0
5
10
15
20
25
30
35
40
0,00 0,20 0,40 0,60 0,80 1,00 1,20 1,40 1,60 1,80
°C
L/H
40% 60% 80%
01.2
0
dantherm.com
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed.• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 40 MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
CDT 40 MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 40 MK III
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
01.2
0
dantherm.com
Specific energy consumption (SEC)• 0.44 kWh/l at 30°C & 80% RH• 0.78 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassette(see separate data sheet)
Also available in this series:CDT 30 MK IIICDT 30 S MK IIICDT 40 S MK IIICDT 60 MK IIICDT 90 MK III(see separate data sheets)
Model CDT 40 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 18.4 l/dDehumidification – 30°C & 80% RH 43.5 l/d Air volume 350 m³/hPower supply 230 V/50 HzMax. ampere consumption 4.1 AMax. power consumption 0.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 40 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 MK II
ohr
93699.24g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351191
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 191
only entended as a guide.
CDT 40 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
545
0
5
10
15
20
25
30
35
40
0,00 0,50 1,00 1,50 2,00 2,50
°C
L/H
40% 60% 80%
All dimensions are in mm.
823
736
539
542
01.2
0
dantherm.com
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser.• Adjustable handle• Plastic bumpers• Low weight• Stackable• Large wheels• On the back two Ø100 mm flex. air ducts may be connected
(max. length of 5 m) (accessory)• Built-in 1 kW heating element• Supplied with high pressure fan
Water container• Water container with handles• Automatic stop when water container is full or removed• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 40S MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
CDT 40S MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 40S MK III
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
01.2
0
dantherm.com
Specific energy consumption (SEC)• 0.44 kWh/l at 30°C & 80% RH• 0.77 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassetteFlex. air ducts Ø100 mm(see separate data sheet)
Also available in this series:CDT 30 MK IICDT 30S MK IICDT 40 MK IICDT 60 MK IICDT 90 MK II(see separate data sheets)
Model CDT 40S MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 18.6 l/dDehumidification – 30°C & 80% RH 43.5 l/d Air volume 560 m³/h*Power supply 230 V/50 HzMax. ampere consumption 8.4 AMax. power consumption with heating element 1.9 kWMax. power consumption without heating element 0.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 58 dB(A)**Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 43 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 40 S MK II
ohr
93418.55g
BEND RADII:
24-05-2012
SCALE: NOT TO SCALE 351192
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 192
only entended as a guide.
CDT 40 S MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
740
825
540
542
0
5
10
15
20
25
30
35
40
0,00 0,50 1,00 1,50 2,00 2,50
°C
L/H
40% 60% 80%
All dimensions are in mm.
*Measured without air ducts mounted.**Measured with air ducts mounted.
823
736
539
01.2
0
dantherm.com
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Stackable.• Large wheels
Water container• Water container with handles• Automatic stop when water container is full or removed• Permanent drainage can be established with optional ½” hose connection• Condensate pump in a cassette as optional extra
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 60 MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
CDT 60 MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 60 MK III
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
01.2
0
dantherm.com
Specific energy consumption (SEC)• 0.42 kWh/l at 30°C & 80% RH• 0.75 kWh/l at 20°C & 60% RH
Accessories½” drain outletRemote hygrostatWall bracketRemote monitoring (IMCS)Condensate pump in a cassette(see separate data sheet)
Also available in this seriesCDT 30 MK IICDT 30S MK IICDT 40 MK IICDT 40S MK IICDT 90 MK II(see separate data sheets)
Model CDT 60 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 28.4 l/dDehumidification – 30°C & 80% RH 65.0 l/dAir volume 725 m³/hPower supply 230 V/50 HzMax. ampere consumption 5.6 AMax. power consumption 1.3 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Water container capacity 14 litresColour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel and water container material PPControl panel material ABSWeight 46 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)only entended as a guide.
CDT 60 MK II
99141.12g
BEND RADII:
CDT 60 MK II
ohr
351193
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH)
25-05-2012
SCALE: NOT TO SCALE
351 193
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
820
905
540
542
All dimensions are in mm
903
816
539
0
5
10
15
20
25
30
35
40
0,00 0,50 1,00 1,50 2,00 2,50 3,00 3,50
°C
L/H
40% 60% 80%
01.2
0
dantherm.com
Dehumidifier• High capacity• Low energy consumption• New eco-friendly refrigerant that meets 2020 EU regulations• Strong and robust cabinet of powder coated hot galvanized steel• Epoxy coated evaporator and condenser• Adjustable handle• Plastic bumpers• Low weight• Large wheels
Water drain• Fitted with a drain outlet for connection to a ½” water hose
Electronic control• Digital touchpad control panel with display• Accurate hour and kWh counter (reading)• RH and °C monitoring (reading)• RH setting• Easy fault-finding• Service monitoring function
FunctionThe CDT 90 MK III is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container.
Applications• Damage service• Building drying• Water works• Dry storing
CDT 90 MK IIIMOBILE DEHUMIDIFIER
FEATURES
MOBILE DEHUMIDIFIERS CDT
Digital touchpad control panel:1. On-off switch2. Reading of room temperature3. Indicator for normal operation (green lamp)4. Reading of RH value / setting of RH value5. Indicator for full water container (yellow lamp)6. Failure indicator (red lamp)7. Hour counter / setting of service intervals8. kWh counter
CDT 90 MK III
DefrostingActive, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.
01.2
0
dantherm.com
Specific energy consumption (SEC)• 0.48 kWh/l at 30°C & 80% RH• 0.81 kWh/l at 20°C & 60% RH
AccessoriesRemote hygrostatRemote monitoring (IMCS)(see separate data sheet)
Also available in this seriesCDT 30CDT 30SCDT 40CDT 40SCDT 60(see separate data sheets)
Model CDT 90 MK IIIOperating range – humidity 40-100% RHOperating range – temperature 3-35°CDehumidification – 20°C & 60% RH 37.0 l/dDehumidification – 30°C & 80% RH 86.5 l/dAir volume 1000 m³/hPower supply 230 V/50 HzMax. ampere consumption 8.3 AMax. power consumption 1.9 kWRefrigerant R454CCompressor type RotarySound level (at 1 metre) 57 dB(A)Colour – cover plate RAL 7044Colour – front and rear grille, cabinet RAL 7015Colour – control panel and bumpers RAL 9005Protection class IP X4Filter PPI 15/G1Wheel size Ø 250 mmWheel material PPControl panel material ABSWeight 62 kg
TECHNICAL DATA
CAPACITY CURVES
DIMENSIONS
MOBILE DEHUMIDIFIERS CDT
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
ohr
Material must comply to Directive 2002/95/EC of the European Parliament. (RoHS)
CDT 90 MK II
355066.95g
BEND RADII:
23-12-2011
SCALE: NOT TO SCALE 351194
MATERIAL:
THICKNESS: WEIGHT:
REV. BY:
DATE:
REF.:
DATE:
PART NO REV.:
RE
V.:
PA
RT
NO
Material must comply to Regulation (EC) No 1907/2006 of the European parliament. (REACH) 351 194
only entended as a guide.
CDT 90 MK II
8
Sheetmetal flatstate is based on Dantherm A/S process equipment and is
table LZT 142 0001, category Surface appearance according to reference
ARE THE PROPERTY OF SAID COMPANY AND WILL BE PROTECTED BY PATENTS
THIS DRAWING IS FURNISHED WITH THE UNDERSTANDING THAT THE ESSENCE THERE OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT WRITTEN AUTHORIZATION BY Dantherm A/S. ALL DESIGNS ORIGINATED BY Dantherm A/S
Linear dimensions without tolerances according to DS/EN 22768-1 mediumAngular dimensions without tolerances: ± 1°
895
980
593
650
All dimensions are in mm
977
894
593
0
5
10
15
20
25
30
35
40
0,00 0,50 1,00 1,50 2,00 2,50 3,00 3,50 4,00 4,50 5,00
°C
L/H
40% 60% 80%
11.1
9
dantherm.com
ACCESSORIES CDT 30 - 40 - 60 - 90 MK III
MOBILE DEHUMIDIFIERS CDT
Illustration Accessory Description CDT type Dantherm no.
Hygrostat When a hygrostat is connected the dehumidifier can operate continuously dependent on the relative humidity in the room.
Two versions are available:Hygrostat with 0.4 m cable, jack plug and fittingHygrostat with 3 m cable and jack plug
AllAll
396242 396241
½” draining tap and screwed hose connector
Ball tap, brass screwed hose connector and clamp for mounting on the water container.
All 396243
Intelligent Remote Monitoring and Control System (IMCS)
IMCS enables you to check the humidifying status in realtime from computers, smartphones and tablets. In addition, you can remotely monitor and control parameters such as power on/off, alarms, temperature and power consumption.
All Please contact sales for more information
Condensate pump in a cassette
Cassette with built-in condensate pump.
Vertical lift: up to 3 metresLength of tube: 10 metres
CDT 30/30S
CDT 40/40S/60
075616
075617
Wall bracket Using the wall bracket the dehumidifier can be hung on the wall.
CDT 30/30S
CDT 40/40S/60
396247
396248
top related