chapter 13 (bearing).ppt
Post on 04-Jun-2018
261 Views
Preview:
TRANSCRIPT
-
8/14/2019 Chapter 13 (bearing).ppt
1/55
13Chapter
Bearing
-
8/14/2019 Chapter 13 (bearing).ppt
2/55
contents
END BEARING Plate bearings (Sliding& hinged bearings). Rocker bearings Roller bearings
Bearing adopted by Railway Board.
-
8/14/2019 Chapter 13 (bearing).ppt
3/55
-
8/14/2019 Chapter 13 (bearing).ppt
4/55
3-The bearings are provided to allow rotation at the ends,when the bridge girders are loaded and deflections take
place.
For all spans in excess of 9 m, the provisions are made forchange in length due to temperature and stress variation.The provisions for expansion and contraction should besuch as to permit movement of the free bearings to theextent of 10 mm for every 10 m of length.
For spans greater than 15m, on rigid pier or abutment, the
bearings, which permit angular rotation at the girder ends,are provided, and at one end, there shall be a roller or othereffective type of expansion bearing.
-
8/14/2019 Chapter 13 (bearing).ppt
5/55
In the design of bearings, provision shall be made for thetransmission of longitudinal and lateral forces to the
bearings and the supporting structures. Provision shall bemade against any uplift to which the bearing may besubjected. All bearings are designed to permit inspectionand maintenance.
Back
-
8/14/2019 Chapter 13 (bearing).ppt
6/55
TYPES END BEARING
Depending upon the magnitude of end reaction, and thespan of bridge, the different types of bearings used for the
bridges are as follows:
1-Plate bearings (Sliding& hinged bearings).
2-Rocker bearings
3-Roller bearings.
4-Bearing adopted by Railway Board.
-
8/14/2019 Chapter 13 (bearing).ppt
7/55
(Sliding&Plate bearings-1
hinged bearings).Plate bearings are simplest type of bearings.The plate bearings are used small spansupto 15 m and small end reaction of the
bridge. Fig. 13-1 shows a plate bearing. The plate bearing consists of two plates.
-
8/14/2019 Chapter 13 (bearing).ppt
8/55
BRIDGE GIRDER
bearing plate
Upper sole plate
CIRCULAR HOLE FOR HINGED BEARING
ELLIPTICAL (SLOTTED) HOLE
FOR EXPANSION BEARING Fig 13-1
-
8/14/2019 Chapter 13 (bearing).ppt
9/55
A sole plate is attached to the bridge. The sole plate restson bearing. The bearing plate is anchored to the concrete.
The two anchor bolts fixed in concrete pass through the bearing plate and the sole plate. The size of bearing plate isfound by the end reaction and the allowable bearing
pressure on the concrete. The plates are made rigid to
distribute the end reaction as uniformly as possibly overthe required area of the concrete.
When the anchor bolts pass through the circular holes inthe sole plate, then, the plate bearings act as hinged
bearing. One end of the bridge girder is hinged oranchored to the concrete through the hinged bearings.
-
8/14/2019 Chapter 13 (bearing).ppt
10/55
The hinged bearings are designed for the end reaction(vertical load) and the lateral forces. The magnitudes of end
reactions used are large. Therefore, the fixed bearingsdesigned for end reactions (vertical loads) only strongenough to take the lateral forces.
In order to allow the longitudinal movement, the slottedholes are provided in the sole plate. In order to reduce thefriction, the surfaces of sole plate and bearing plate incontact are well machined and smoothly finished. The sole
plate can slide upon the bearing plate. The plate bearingsact as expansion bearings of sliding type. In the expansion
bearing, the longitudinal movement (expansion orcontraction) takes place with change of temperature and
loads
-
8/14/2019 Chapter 13 (bearing).ppt
11/55
The longitudinal force at any free bearing shall be limitedto the dead load reaction at the bearings multiplied by thecoefficient of friction. The coefficients of friction fordifferent surfaces in contact are given in clause 6.10(Egyptian code for loads).
The plate bearings have bearing two disadvantages. Theedge of plate nearest to the end of span has a tendency tolift along with the deflection of bridge girder. Therefore,the end reaction is not distributed uniformly. Secondly, inorder to have longitudinal movement, the sliding frictionis to be overcome. Therefore, for the large span bridges,the more efficient devices are necessary.
-
8/14/2019 Chapter 13 (bearing).ppt
12/55
The end reaction is distributed uniformly by providing adeep cast steel bed block as shown in Fig. 13-2 .
Such bed blocks have adequate rigidity. The sole plate bearings are many times made curved as shown in Fig. 13-3.
The curved sole plate allows rotation. For large spans, the
plate bearings are not suitable. The hinged (rocker) bearingsand roller bearings are used in such cases.
The sliding bearing is the least expansive bearing for lightand intermediate reactions.
-
8/14/2019 Chapter 13 (bearing).ppt
13/55
BRIDGE GIRDER
Fig 13-2
Back
-
8/14/2019 Chapter 13 (bearing).ppt
14/55
BRIDGE GIRDER
ELLIPTICAL (SLOTTED) HOLEFOR EXPANSION BEARING
CIRCULAR HOLE FOR
HINGED BEARING
Fig 13-3
Back
-
8/14/2019 Chapter 13 (bearing).ppt
15/55
Figure 13-4 shows a bearing that makes use of a rocker between the bearing plate and the beam or girder.
Hex . nut andwasher,fixed end
hole fixed endSlotted hole in rocker ,exp.end
Performed fabric pad or grout
Hex . and jam nut
expansion end
Anchore bolts LC
brg
Fig 13-4
-
8/14/2019 Chapter 13 (bearing).ppt
16/55
A similar detail in which the anchor bolts do not passthrough the rocker is shown in Fig. 10.3. In this case, the
beam is held in position by means of pintles shaped likegear teeth. This type of support may be used whereresistance to uplift need not be provided. For example, itmay be used for inside beams of the beam bridge, with the
outside beams supported by bearings of the type as shownin Fig. 13.5 .
-
8/14/2019 Chapter 13 (bearing).ppt
17/55
Round hole in rocker,fixed.end
Slotted hole in rocker,exp.end
ExpFix
Performed fabric pad or grout
Driving fit
Pintle detail
LCCL brg brg
Fig 13-5
-
8/14/2019 Chapter 13 (bearing).ppt
18/55
Figure 13-6a shows an expansion bearing for larger bridges.Several variations are shown in the view at the right. Thesole plate may be bolted to the girder, as at the left of thecenterline, or welded as shown at the right. Resistance touplift may be provided by using a hinge plate, as at the left;if such resistance is needed, lateral movement is prevented
by a plate such as that shown at right. A correspondinghinged end bearing is shown in Fig. 13-6b.
-
8/14/2019 Chapter 13 (bearing).ppt
19/55
2 bolts in each side
(b)
(a)
Topered hole
in rocker
PL
2 bolts in each side
Fig 13-6
-
8/14/2019 Chapter 13 (bearing).ppt
20/55
Although there is only a line of contact between an unloadedrocker and its bearing plate, deformation under loaddistributes the reaction over a finite area. Evidently, at agiven load this area increases with increase in radius of therocker, since a rocker of infinitely large radius would have a
plane surface to begin with. The allowable load must be
evaluated in terms of limiting permanent deformation. Thusthe yield point of the material is also a factor.
These bear ings consist of :
An upper sole plate; in rolled steel riveted to the girder. Forhinged bearing the sole plate is provided with two grooves inwhich two ribs in the bearing plate in gage and thus thehorizontal movement isnt available.
-
8/14/2019 Chapter 13 (bearing).ppt
21/55
2R
=M
2cm/t4.1I
yM =f
12t b
=I311
12t b
=I
2/t2R =f 311
1
& y = t 1/ 2
t1 (3 - 4) cm
-
8/14/2019 Chapter 13 (bearing).ppt
22/55
aHinged bearing
Movable bearing
Bearing plate
Upper sole plate
1 b b 2
b 2 1 b
R/2
t 21t
a
a
rib
rib
R/2
-
8/14/2019 Chapter 13 (bearing).ppt
23/55
2- Abearing plate of cast steel (or cast iron for small RoadwayBridges).
Fixed to masonry by ribs.The size of the bearing plate is obtained from the allowable bearing
pressure on masonry for granite & basalt or similar hard stones 40kg/cm 2. For reinforced with circular hoops 70 kg/cm 2.
R
Bearing plate
B.M.D
2t
R/2
a
-
8/14/2019 Chapter 13 (bearing).ppt
24/55
4a
2R
=M
2cm/t8.1I
yM =f 12
t b =I322
22
322
2get t steelCastcm/t8.1
12t b
2/t4a
2R
I
yM =f
& y = t 2/ 2
The bearing plates for hinged andmovable bearings are the same size.
The bearing plate shall rest on a 3 mmsheet of lead and shall provided withmasonry ribs to transmit thehorizontal reaction of the bridge.
ribSBack
-
8/14/2019 Chapter 13 (bearing).ppt
25/55
Fig. 13-8 shows a typical rocker bearing.
BRIDGE GIRDER
Fig. 13-8
2-Hinged (Rocker) bearings
-
8/14/2019 Chapter 13 (bearing).ppt
26/55
The cast steel sole and cast steel bearing block are used inthese types of bearings. A cylindrical pin is inserted in
between the cast steel sole and the cast steel bearing block.This pin allows rotations at the ends of bridge girder. Therocker bearing acts as hinged bearing. The end reaction ofa bridge girder is transmitted to the pin
by direct bearing through the sole attached with the girder.The vertical plates are used to transmit the end reaction.The number of plates (two or three) depends upon the
magnitude of end reaction. The end reaction is furthertransmitted to the cast steel bearing block and then to thesupporting structure.
-
8/14/2019 Chapter 13 (bearing).ppt
27/55
Two outer vertical plates completely encircle the pin. Incase, the bearing is subjected to an uplift, then, the uplift isresisted by theses plates. The middle plates provide only
bearing with the cylindrical surface of the pin. The required bearing area is provided by the product of total thickness of plates and the diameter of pin. The thicknesses of all the plates are kept equal. Therefore, the end reaction istransmitted equally by these plates. The value of bendingmoment is found by multiplying force transmitted by outer
plate of the sole to the outer plate of bearing block and
center to center distance between these plates. The size of base plate is found by the allowable bearing stress in theconcrete and the end reaction.
-
8/14/2019 Chapter 13 (bearing).ppt
28/55
The rocker bearing are also bearings are also subjected tolateral and longitudinal forces in addition to the endreaction (vertical loads). The increase of end reaction dueto lateral and longitudinal forces is also taken intoconsideration. The lateral forces and the longitudinal forcesare assumed to act at the level of cylindrical pin of the
rocker bearing. The base plate is subjected to momentalong both the directions. The total bearing stress in theconcrete should not exceed the allowable bearing stress.
The rocker bearings are designed for the end reaction andthen checked for lateral forces and longitudinal forces.
Figure 3.54 shows the rocker bearing for the hinged end.
-
8/14/2019 Chapter 13 (bearing).ppt
29/55
In the rocker bearing for free end of the bridge girder theunderside of sole is curved, which rotates on the horizontal
bearing plates and allows longitudinal movement. This actsas rocker type expansion.
Back
-
8/14/2019 Chapter 13 (bearing).ppt
30/55
3-Roller bearings. The roller bearings as shown in Fig. 13-9 are also usedfor the long span bridges. Fig. 3.55 (A) shows a singleroller used in the bearing.
The rollers provide the rotation as well as thelongitudinal movement. Fig. 3.55 (B) shows number ofrollers used in the bearing. The bearings act as roller type
expansion bearings. The rollers are kept in position bymeans of dowels, lugs or keys as shown in Fig. 3.55 (A).
The roller bearings for spans above span 35 m should
preferably be protected from dirt by oil or grease box.
-
8/14/2019 Chapter 13 (bearing).ppt
31/55
So long as, the size of rollers is small, the completecircular rollers are provided. When the size of rollers
become large, then, the sides of rollers are cut in order toreduce the length of the sole, and to make the bearingsmore compact. These rollers with cut sides are known assegmental rollers.
-
8/14/2019 Chapter 13 (bearing).ppt
32/55
BRIDGE GIRDER
SEGMENTAL ROLLER
SEGMENTAL ROLLER
BRIDGE GIRDER
Fig 13-9
Back
f
-
8/14/2019 Chapter 13 (bearing).ppt
33/55
In order to avoid overturning or displacement of theserollers, these are geared with upper and lower plates. Thespacing between segmental rollers and the width of rollers
may by found as below:It is assumed that the rollers don not slip but only roll duringrolling. When, the roller rolls to the maximum position, as
shown in Fig. 13-10,
b
d
d + b
d + a
a
B
D/2
D
d
d + a
Fig 13-10
-
8/14/2019 Chapter 13 (bearing).ppt
34/55
then, the vertical axis of roller turns through an angle , andthe center of the roller travels through a forward motion, B.
Then,
travelHorizontalR
roller segmentalof Diameter D
roller segmentalof WidthdDd
sin
D114.6B
sinDd
,Therefore
)degreesin(D
B6.114)radiansin(
DB2
tan
(3.15)
(i)
-
8/14/2019 Chapter 13 (bearing).ppt
35/55
The distance between adjacent segmental rollers a, (i.e. the spacing between the segmental rollers) should be such that the rollers do notcome in contact during the forward motion.
Then, (a +d) = (d+b) sec (iii)
a = b sec + d (sec - 1)(3.16)
Where, b = Least allowable perpendicular distance between the facesof adjacent, after their revolved positions.
The spacing between adjacent segmental rollers a, is found, knowing
b, d and .The roller bearings are also used to support the cast steel sole with pin
bearings as shown in Fig. 13-11 . In such cases the roller also acts as ahinged bearing.
-
8/14/2019 Chapter 13 (bearing).ppt
36/55
Fig 13-11
-
8/14/2019 Chapter 13 (bearing).ppt
37/55
The following points are kept in mind while designing ssole a pedestal for the roller bearing.
1. The sole transmits the end reaction to the pin. Theend reaction must be distributed from the pin to the variousrollers uniformly.
2. The size and number of rollers provided should beadequate to have proper stress and free movement.
3. The rollers should be so arranged that these can be
readily cleaned of accumulated dirt and dust.4- Segmental rollers (Fig. 13-12) are ordinary used since
they occupy less space than cylindrical rollers.
-
8/14/2019 Chapter 13 (bearing).ppt
38/55
The rollers may be coupled with the sidebars shown andthe entire nest held in position by tooth guides whichengage slots in the shoe and in the bearing plate. Sidebarsmay be omitted if each roller is held by teeth. Lateralmovement is prevented by the tongues shown in the viewat the right.
1. Resistance to uplift may be provided by lugs thathave projections extending over the upper surface of the
base of the shoe or by enlarging the base of the shoe and providing slotted holes for the anchor bolts. The rollerassembly may be enclosed with removable dust guards;they are shown on only two sides in Fig 13-12 to indicatethat they are optional.
BoltC Pi
-
8/14/2019 Chapter 13 (bearing).ppt
39/55
Removabledust guard
Side bars
BoltCap
Tongue
Pin
The roll er bearings consist of the foll owing par ts
1-Upper sole plate in structural steel or cast steel or cast/steel riveted to the plate girder.
2-A lower sole plate (saddle) in cast steel with a curvedupper surface and a plain lower surface which bears upon the
rollers.
-
8/14/2019 Chapter 13 (bearing).ppt
40/55
Its dimensions depend upon the number of rollers theirdiameter and clearance left between the rollers. It must
project on either side to allow for longitudinal movementof the bridge.
In case of two rollers the B.M. at center of plate = V S/ 4
In case of three rollers or more the saddle plate acts as acontinuous beam of variable inertia by three rollers thecentral one will carry most of the load. For this reason it isgenerally preferred to have the number of rollers either
(1& 2& 4& 6& 8).
-
8/14/2019 Chapter 13 (bearing).ppt
41/55
R/2
Lower sole plate
Upper sole plate
Lower bearing plate
a
R/2
bRollers
1t
-
8/14/2019 Chapter 13 (bearing).ppt
42/55
The rol lers
The size of rollers depends upon the maximum reaction on oneroller and the material of construction.
Formula of Hertz for contact between a plane and cylinder of radiusR and length L is;
r
1
L
VE
4
3max
2E
P16
9R
Assuming equal distribution of the reaction V on allrollers;
L
-
8/14/2019 Chapter 13 (bearing).ppt
43/55
2
2
EV89
dLn
Or
E
nL
V
16
9R
nLV
P
For Cast I ron ; E = 1000 t/ cm 2, max = 5.0 t/cm2
V32.14dLn
-
8/14/2019 Chapter 13 (bearing).ppt
44/55
For Rol led Steel ; E = 2100 t/ cm 2, max = 6.50t/cm 2
For Cast Steel ; E = 2200 t/ cm 2, max = 8.50t/cm 2
ForF orged Steel
; E = 2200 t/ cm2
, max = 9.50t/cm 2
V8.17dLn Ld055.0nV
V9.10dLn Ld095.0nV
V7.8dLn Ld117.0nV
-
8/14/2019 Chapter 13 (bearing).ppt
45/55
V/2 V/2
The rollers are provided with wider discs to take up thelateral reaction. The rollers are coupled together by strongside bars, serving as spacers allowing (2 - 4) cm betweenevery two rollers. The diameter of the rollers shall be notless than 12 cm and not more than 35 cm.
4-The lower bearing plate
It distributes the concentratedreaction of the rollers upon awider bearing area of the
abutment. We generallyassume uniform upward
pressure and the plate acts asa beam with over hangingends. Back
-
8/14/2019 Chapter 13 (bearing).ppt
46/55
4-Hinged bearings with a
bearing block It used for longer spans and consist of an
upper sole plate riveted to the girder and a
bearing block.The bearing block is made of cast steel (orcast iron for small Roadway bridges) withlongitudinal and transverse ribs.
For vertical reaction only the pressure on theabutment;
40 k / 2 f B l d G i
-
8/14/2019 Chapter 13 (bearing).ppt
47/55
baV
= perm 40 kg/ cm
2 for Basalt and Granite
70 kg/cm 2 for Reinforce Concrete
Including the effect of horizontal reactions in thelongitudinal and transverse directions then:
V
H
-
8/14/2019 Chapter 13 (bearing).ppt
48/55
a
V
t
(0.2-0.3)h
SEC s-s b
b
t
1nt
2
HL
t(0.15-0.2)h
(0.2-0.3)h
fc
ft
s t
h t
s
HT
hHhHV
-
8/14/2019 Chapter 13 (bearing).ppt
49/55
6ab
hH
6 ba
hH ba
V =
2tT
2tL
1.15 perm
The height h t of the hinged bearing is practically takenequal to that of the opposite movable bearing
The maximum stressed section is S S, it is equivalent to aT section with a web 4 t 1.
x
uc I
yM =f
x
Lt I
yM =f
4a
2V =M
and
For cast i ron F t all = 400 kg/cm2
Fc all = 1000 kg/cm2
-
8/14/2019 Chapter 13 (bearing).ppt
50/55
For cast steel F all = 1800 kg/cm2
Thickness of lower flange = (1/3 1/5) h t
Total n t 1 = (1/4 1/5) of the total width b
Thickness of central web 1/6 h t
The upper surface of the bearing block must be curved to acount for end slop of the girder. The lower surface of thesole plate may be either straight or curved. The face of thecontact is a line in the unloaded condition. Under the load it
becomes a rectangle. The width which (b) increased withincrease at loads.
Hertz formula for contact between two curved surfaces;
-
8/14/2019 Chapter 13 (bearing).ppt
51/55
v
6 max
t h /6
b
e
h /6t
b1
2R
R
-
8/14/2019 Chapter 13 (bearing).ppt
52/55
b = width of area of contact
lengthsupportingl
lengthunit perloadl
V where
r /1r /1
CC2 b
21
21
r 1 & r 2 = radii of upper and lower surfaces
22
12
21
11
1E4
C
1E4
C
-
8/14/2019 Chapter 13 (bearing).ppt
53/55
where E & = 1/m are the modulus of elasticity andPoisson ratio of the two materials.
m = 3 for steel & m = (2 4) for all the materials
Assuming the elliptical pressure distribution over thenarrow strip b
L bV4
L4
bV
max
max
For the case E 1 = E 2 = E, and 1 = 2 = = 1/3
-
8/14/2019 Chapter 13 (bearing).ppt
54/55
21
max r 1
r 1
LVE
43
For a flat lower surface of sole plate and 1/r 1 = 0
r
E
L
V423.0
r L
VE
4
3
2max
-
8/14/2019 Chapter 13 (bearing).ppt
55/55
The allowable pressure max can be taken much higherthan the working stress;
In compression max = 5.0 t/cm 2 Cast I ron
max = 6.5 t/cm2 Rol led Steel
max = 8.5 t/cm2 Cast Steel
max = 8.5 t/cm2 F orged Steel
F orged Steel = Rol led Steel but subjected to temperaturesup to 800 900 1000 C
Back
top related