chapter 3 dc and parametric measurements. © 2000 r. j. fink n continuity – purpose of continuity...
Post on 23-Dec-2015
228 Views
Preview:
TRANSCRIPT
© 2000 R. J. Fink
– Purpose of Continuity Testing Electromechanical relays
Sinlge Pole,Single Throw
(SPST)
Sinlge Pole,Double Throw
(SPDT)
Double Pole,Double Throw
(DPDT)
ContactWiper
Coil
© 2000 R. J. Fink
Continuity– Continuity Test Technique
On chip protection diodes– Protect input and output from Electrostatic Discharge (ESD)
and other overvoltage– Pins have either one or two reverse biased diodes
© 2000 R. J. Fink
Continuity– Continuity Test Technique
Force current - measure voltage– DUT power supplies are grounded– Current level is usually between 100uA and 1mA– Diodes connected to the positive supply - current forced in– Diodes connected to the negative supply - current forced
out– Output diode voltage drop usually is between 550mV and
750mV– If tester does not see diode voltage drop or the current
reaches its voltage clamp, the test fails
© 2000 R. J. Fink
Continuity– Serial vs. Parallel Continuity Testing
Serial is one pin at a time– Test time intensive
Parallel can not see pin to pin shorts– Alternating odd and even pin parallel test
Analog parallel per-pin measurement is not available in some testers
– Single current source and volt meter can be used one pin at a time
Digital per-pin measurement is available, but may introduce noise into sensitive analog circuit
© 2000 R. J. Fink
Leakage Currents– Purpose of Leakage Testing
Good design should have leakage current of less than 1uA
Detects poorly processed integrated circuits– Improper operation in customer end application
Detect weak devices – Initially function but eventually fail after unacceptably
short lifetime (Infant mortality)
© 2000 R. J. Fink
Leakage Currents– Leakage Test Technique
Force DC voltage - measure small current – Typically measured twice
• input voltage equal to positive supply• input voltage set to ground or negative supply
– Input current high (IIH) and input current low (IIL)– Digital and analog inputs
Output leakage current (IOZ)– Measured same as IIH & IIL
• output pin must be placed in a high impedance (HIZ) state using test modes
© 2000 R. J. Fink
Leakage Currents– Serial vs. Parallel Leakage Testing
Serial is one pin at a time– Test time intensive– Less possibility of errors
Leakage currents can flow from pin to pin– Alternating odd and even pin parallel test is recommended
Again, analog parallel per-pin measurement is not available in some testers
– Single voltage source and current meter can be used one pin at a time
Again, digital per-pin measurement is available, but may introduce noise into sensitive analog circuit
Power Supply Currents– Importance of Supply Current Tests
Fast method for determining catastrophic failure– Large current draw from power supplies– Tests are run early in test protocol to weed out defective
chips without wasting valuable test time– Older technologies easier to diagnose
Customer specific application characteristic– Battery operated instruments like a cellular phone require
minimal current draw by electronics
Power Supply Currents– Test Techniques
Basic test is simple– Testers have the ability to measure current draw from power
supplies (Idd and Icc)
Actual test is never basic– Test conditions
• must be clearly identified in test plan• power up mode, standby mode, normal operational mode • digital supply (Iddd and Iccd) and analog supply (Idda
and Icca) measured separately– Worst case
• requires complete characterization
– Test Techniques - cont.– Multiple power supply pins
• designers may need to know the current flow into each pin
– Settling time• 5 to 10 milliseconds in active mode• hundreds of milliseconds to stabilize to within 1mA
DC References and Regulators– Voltage Regulators
High voltage input - regulated lower voltage output– Output voltage
• simple voltmeter reading– Output voltage regulation
• ability of regulator to maintain specific output under load
– Dropout voltage• minimum input voltage before output drops below
specified level – Input regulation
• ability of regulator to maintain steady output with a range of input voltages
DC References and Regulators– Voltage References
Low power voltage regulators– Not always accessible from external pin
• test engineer may need to request test modes to test references
– May not have a separate specification in the data sheet– DC reference test modes allow the program to trim the DC
references for more precise device operation
Load regulation is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in the supply's load (such as a change in resistance value connected across the supply output)Load regulation of a constant-voltage source is defined by the equation:
For a constant-current supply, the above equation uses currents instead of voltages, and the maximum and minimum load values are when the largest and smallest specified voltage across the load are produced.
Load Regulation
loadnom
loadload
VL
O
V
VV
I
V
I
_
max_min_
minimum
%100Regulation Load%
}max{Regulation Load
Vmax_load = voltage at maximum load. The maximum load is the one that draws the greatest current,(never short circuit);Vmin_load= voltage at minimum load. The minimum load is the one that draws the least current,Vnom_load= voltage at the typical specified load.For a constant-current supply, the above equation uses currents instead of voltages, and the maximum and minimum load values are when the largest and smallest specified voltage across the load are produced.
Load Regulation
loadnom
loadload
VL
O
V
VV
I
V
I
_
max_min_
minimum
%100Regulation Load%
}max{Regulation Load
Line regulation is the capability to maintain a constant output voltage level on the output channel of a supply despite changes to the input voltage level.In linear regulators, the output voltage is affected by the input voltage. Line regulation measures how much it is affected:
Line Regulation
L
L
IinitO
finalOinitO
II
O
V
VV
V
V
maximum ,
,,
maximum
%100Regulation Line
}max{Regulation Line
Line Regulation Example
1. Find the difference between the initial voltage and the maximum fluctuation. – If the initial voltage was 25 and the maximum
measurement was 28, then the difference in voltage would be 3 volts.
2. Divide the change in voltage by the initial voltage. – Using the above example, 3/25= .12
3. Multiply the number obtained in Step 2 by 100.– This will give you the line regulation percentage for the circuit or
current you are measuring. Ex: .12 x 100 = 12%
Problem 1 - 10 Minute
– A) The output of a 9-V voltage regulator varies from 8.95 V under no-load condition to 8.15 V under a 15 mA maximum rated load current. What is its load regulation?
– B) The output of a 9-V voltage regulator varies from 8.65 V to 8.22 V when the input voltage is changed from 14 V to 6 V under a maximum load condition of 5 mA. What is its line regulation?
– C) A 9-V voltage regulator is rated to have a load regulation of 15 mV/mA for a maximum load current of 10 mA. Assuming a no-load output voltage of 9-V, what is the expect output voltage at the maximum load current?
Problem 1 - Solution
mAmVmA
VV
I
V
IVL
O /3.5315
15.895.8
}max{Regulation Load
minimum
VmVVV
VV
V
V
LII
O /75.53614
22.865.8
}max{Regulation Line
maximum
VV
mA
VVmAmV
I
V
load
load
VL
O
I
85.8
10
9/15
}max{Regulation Load
minimum
DC References and Regulators– Trimmable References
Allows quality of product to be enhanced during testing through fuses internal to the device
– The only aspect of testing that adds value to the device
Fuses, Zener diodes or EEPROM register bits– Fuses and Zener diodes are blown by forcing a controlled
current through them• fuses blow to an open circuit• diodes blow to a short circuit
Laser trimming– On-Chip resistor are trimmed to increase resistance– Also used to trim gain and offset of analog circuits
Trimming is sometimes performed after packaging to account for packaging effects
Impedance Testing– Input Impedance
Very common specification for analog inputs – Force two voltages - measure differences in current
• single voltage / current is not sufficient to eliminate bias current and unknown termination voltages
• data sheet will list the appropriate range for voltage – Input impedance is equal to change in voltage divided by
the change in current– Alternative method: force two controlled currents and
measure the voltages• used in cases where low input impedance would
cause excessive current flow into the device• data sheet will list the appropriate ranges of current
Impedance Testing– Output Impedance
Typically much lower than input impedance– Measured with a force current measure voltage method
– Differential Impedance Measurements Force two differential voltages and measure the
differential current change
DC Offset Measurements– Output Offset Voltage
The difference between the devices ideal output voltage and its actual output voltage
Basic test is fairly simple Difficulties
– AC components or noise riding on the DC signal– Requires filtering
• analog low pass filter• digital averaging which functions like a low pass
filter– ATE parasitic capacitance
• causes some op amps to oscillate• may need a buffer amplifier
© 2000 R. J. Fink
DC Offset Measurements– Input Offset Voltage
Output offset voltage referenced back to its input– Output offset voltage divided by the gain of the circuit
• definition assumes that the offset is all attributed to the input, when in reality, the offset could be caused by internal factors as well
– Single Ended, Differential, and Common Mode Offsets
– Single ended offsets are measured relative to ideal voltage – Differential offset is the difference between two outputs
of a differential circuit.– Common mode offset is the average voltage level at two
outputs of a differential circuit compared to an ideal common mode voltage
© 2000 R. J. Fink
DC Gain Measurements– Closed Loop Gain
Single input– Change in output divided by the change in input– Use a voltmeter to measure output
• input should be stable to within 1mV • may need testers high accuracy voltmeter to measure
the values
Differential input– Change in differential output divided by change in
differential input– DC offsets at the input are cancelled out– Use a differential voltmeter
© 2006 G.O. Ducoudray
Problem 2 - 5 Minute– Given a fully-differential amplifier with a nominal gain of +10 V/V.
SRC1 is set to 1.6 V and SRC2 is set to 1.4 V. An output voltage of 2.53 V is measured at OUTP and an output voltage of 0.48 V is measured at OUTN. Then SRC1 is set to 1.4 V and SRC2 is set to 1.6 V and output voltage of 0.49 V is measured at OUTP and output voltage of 2.52 V is measured at OUTN. Using the measured data provided, what is the differential gain of this circuit?
Problem 2 - Solution
– With SRC1 set to 1.6 V and SRC2 set to 1.4 V, you get a differential input of 200 mV.
– An output voltage of 2.53 V is measured at OUTP and an output voltage of 0.48 V is measured at OUTN, the differential output is 2.05 V.
– With SRC1 is set to 1.4 V and SRC2 is set to 1.6 V you have an input differential level of –200 mV.
– An output voltage of 0.49 V is measured at OUTP and an output voltage of 2.52 V is measured at OUTN, the differential output voltage is thus -2.03 V.
VV 2.10
m 200m 002
) 03.2( .052
VV
VVG
© 2006 G.O. Ducoudray
DC Gain Measurements– Open Loop Gain
Defined as the amplifier gain with no feedback path from the output to the input.
– Difficult to test since op amp gains can be very high• measured using a second op amp in the feedback path • nulling amplifier can also be used to measure the
input offset voltage
VO-NULLVM
DUT
Tester
SRC1
VSRC1 Tester
VMID
R3
VMID
R2
R1
R1
R3
Nulling Amp
CV -
DUT
V +DUT
VO-DUT
© 2006 G.O. Ducoudray
DC Power Supply Rejection Ratio– DC Power Supply Sensitivity (PSS)
Measure of the ability of a circuit to maintain a steady output voltage while the power supply voltage changes slightly
VOVM
DUTTester
x10 Amplifier (On-Chip VMID)
SRC1
VDD
TesterVOUT
VMID
VIN1 k
10 k
VMID
VDD
VSS
© 2006 G.O. Ducoudray
DC Power Supply Rejection Ratio– DC Power Supply Rejection Ratio (PSRR)
PSS of the circuit divided by the gain of the circuit in its normal mode of operation
PSRR|db = 20 log PSS/|G|
© 2006 G.O. Ducoudray
Problem 3 - 10 Minutes
– The input of the x10 amplifier is connected to a voltage source forcing 0.25 V. The power supply is set to 4.9 V and a voltage of 2.52 V is measured at the output of the amplifier. The power supply voltage is then changed to 5.1 V and the output measurement changes to 2.56 V. What is the PSS? What is the PSRR if the measured gain is 9.8 V/V?
© 2006 G.O. Ducoudray
Problem 3 - Solution
– Please note changes in text p. 3-31• Solution to problem should be 9mV/V and -40.91 dB
dB 98.13 200 V 4.9-V 5.1
V 2.52-V 2.56
VmV
V
VPSS
PS
O
VV 20.408=
V/V 9.8
mV/V 200=
+
mG
PSSPSRR
© 2006 G.O. Ducoudray
DC Common Mode Rejection Ratio– CMRR of Op Amps
A differential circuit’s ability to reject a common mode signal at its inputs
There are two circuits used to measure CMRR– Resistor matching is a major source of error.
voltageinputecommon
voltageoffsetinputCMRR
__mod_
__
VoltageInputModeCommon
VoltageOffsetInputCMRR
___
__
© 2006 G.O. Ducoudray
Op amp CMRR Test Setup
VOVM
DUT Tester
SRC1
VSRC1
Tester
VOUT
VMID
IN
RF
RF
IN+
VMID
Op Amp (On-Chip VMID)
RI
RI
© 2006 G.O. Ducoudray
CMRR Test Setup using Nulling Amplifier
VO-NULLVM
DUT
Tester
SRC1
VSRC1
TesterVMID
R3
VMID
R2
R1
R1
R3
Nulling Amp
C
© 2006 G.O. Ducoudray
DC Common Mode Rejection Ratio– CMRR of Differential Gain Stages– Circuits that use op amps to perform a function
– The CMRR of the op amp is not as critical as the CMRR of the circuit.
– Resistor matching is critical in these circuits
Difference between chip CMRR and circuit CMRR?– Chip CMRR - the resistors are on the DIB.– Circuit CMRR - the resistors are on the DUT.
Gain
VV
CMRR in
out
© 2006 G.O. Ducoudray
CMRR of Differential Gain Stages
VOVM
DUTTester
Differential x10 Amplifier (VMID Generated On-Chip)
SRC1
VSRC1
Tester
VOUT
VMID
IN1 k
10 k
IN+
1 k10 k
© 2006 G.O. Ducoudray
Comparator DC Tests– Input Offset Voltage
Differential input voltage causes a comparator to switch from one output state to the other.
– Differential input voltage is ramped from one voltage to another to find the point at which the comparator changes state.
VOVM
DUT Tester
SRC1
VIN+
Tester
VOUT
IN
IN+
Comparator
VINVM
SRC2
VIN -
© 2006 G.O. Ducoudray
Comparator DC Tests– Threshold Voltage
Slicer circuit– Fixed reference voltage supplied to one input of a
comparator– The input offset voltage is replaced by the single-ended
specification, threshold voltage
VOVM
DUT Tester
SRC1
VIN+
Tester
VOUT
IN+
Slicer
VINVM
VTH
© 2006 G.O. Ducoudray
Comparator DC Tests– Hysteresis
The difference in threshold voltage between a rising input test condition and a falling input condition
– May or may not be a design feature
Input offset voltage and hysteresis may change with different common mode input voltages
© 2006 G.O. Ducoudray
Voltage Search Techniques– Binary Searches vs. Step Searches
Ramping input voltages until an output condition is met is called a ramp or step search.
– Very time consuming, not well suited for production testing.
Binary searches use successive approximation algorithms
• If you are looking for a transition between 1.45V and 1.55V, the comparator input is set to 1.5V and the output is observed. If the output is high, then the input is increased by one quarter of the 100 mV search range (25mV) to try to make the output go low. Once the output goes low, the input is adjusted by one eighth of the search range (12.5mV) and the process is repeated until the desired resolution is attained.
• Does not work well in the presence of hysteresis.© 2006 G.O. Ducoudray
Voltage Search Techniques– Linear Searches
Very fast Using two input values, two output values can be
measured.– Using the linear equation: y = m * x + b, the zero
crossing values can be calculated.
Iterative linear searches are used to achieve the desired accuracy.
© 2006 G.O. Ducoudray
DC Tests for Digital Circuits– IIH / IIL
Mentioned earlier under leakage currents– Data sheets list several specification for digital inputs and
outputs– Digital I/O lines can also have input leakage specifications
when they are set in a high impedance (HIZ) mode.
– VIH / VIL (input high voltage and low voltage) Threshold voltage for digital inputs
– Tested using a binary or step search– Force levels as a go-nogo test
• to identify VIH / VIL threshold failures, rerunning the go-nogo test at a looser test limit will reveal the failure.
© 2006 G.O. Ducoudray
DC Tests for Digital Circuits– VOH / VOL
VOH is the minimum output voltage in the high state
VOL is the maximum output voltage in the low state– Usually a verified value not a measured value– Tested using a go-nogo test
– IOH / IOL VOH and VOL are guaranteed with specified load
currents (IOH and IOL)– When output is high, the tester must pull current out of the
DUT.– When the output is low, the tester must force current into
the DUT.
© 2006 G.O. Ducoudray
DC Tests for Digital Circuits– IOSH and IOSL Short Circuit Current
Digital outputs often have output short circuit protection
– If the output is shorted directly to ground or to power, the amount of current flowing into or out of the pin is limited to IOSH and IOSL
© 2006 G.O. Ducoudray
Summary– DC tests are very easy to define and understand– Actual testing is usually much more difficult
than it looks. A DC offset of 100mV is easy to measure with an
accuracy of +/- 10mV - very difficult to measure with an accuracy of 1uV.
Accuracy and repeatability are often the most time consuming problems faced by an analog test engineer.
© 2006 G.O. Ducoudray
top related