development of new remediation technologies for
Post on 20-Apr-2022
3 Views
Preview:
TRANSCRIPT
Resource-Efficient Technologies 3 (2017) 166–176
Contents lists available at ScienceDirect
Resource-Efficient Technologies
journal homepage: www.elsevier.com/locate/reffit
Research paper
Development of new remediation technologies for contaminated soils
based on the application of zero-valent iron nanoparticles and
bioremediation with compost ✩
A. Galdames a , ∗, A. Mendoza
b , M. Orueta
b , I.S. de Soto García
c , M. Sánchez
b , I. Virto
c , J.L. Vilas a
a Physical Chemistry Department, Faculty of Science and Technology, University of the Basque Country/EHU, 48940 Leioa, Spain b Iragaz Watin S.A., 20720 Azkoitia, Spain c Departamento Ciencias del Medio Natural, Universidad Pública de Navarra, 31006 Pamplona, Spain
a r t i c l e i n f o
Article history:
Received 29 July 2016
Revised 27 March 2017
Accepted 27 March 2017
Available online 22 May 2017
Keywords:
Bioremediation
Soils
nZVI
Hydrocarbons
Metals
a b s t r a c t
This study aimed to develop new techniques for the remediation of contaminated soils based on the ap-
plication of zero-valent iron nanoparticles (nZVI) and bioremediation with compost from organic wastes
and a mixed technique of both. An assessment of the effectiveness of remediation in two soils contami-
nated with hydrocarbons and heavy metals was carried out, with the aim of looking for positive synergies
by combining the two techniques, and demonstrating their viability on an industrial scale. The applica-
tion of nZVI for in situ immobilization of As and Cr in two different soils (Soil I from a contaminated
industrial site and Soil II, contaminated artificially) showed a decrease in the concentration of As in Soil
I and Soil II, as well as a decrease in Cr concentration for Soil I and Soil II in the leachate of both soils.
The addition of compost and nanoparticles under uncontrolled environmental conditions in biopiles was
able to produce a decrease in the concentration of aliphatic hydrocarbons of up to 60% in the two soils.
Especially, degradation and transformation of longer chains occurred. A significant reduction of ecotoxic-
ity was observed throughout the process in the biopile of soil II, not reaching the LC50 even with 100%
of the sample after the treatment, in both earthworm and seeds growth tests.
© 2017 Tomsk Polytechnic University. Published by Elsevier B.V.
This is an open access article under the CC BY-NC-ND license.
( http://creativecommons.org/licenses/by-nc-nd/4.0/ )
T
e
t
f
d
c
g
t
i
i
o
p
1. Introduction
The ceasing of industrial activity has left behind a large amount
of contaminated sites on the periphery of urban areas (brown-
fields) that are characterized by soils with high concentrations of
organic and inorganic compounds (mixed pollution). Mixed pol-
lution generates problems to determine the pollution nature and,
consequently, makes the selection of the technologies that must
be applied for the removal of contaminants difficult. Each pol-
luted site has its own characteristics related to the typology of
pollutants, the concentration levels of these, hydrogeological char-
acteristics of the environment, biogeochemical soil properties, etc.
✩ Peer review under responsibility of Tomsk Polytechnic University. ∗ Corresponding author. Physical Chemistry Department, Faculty of Science and
Technology, University of the Basque Country/EHU, 48940 Leioa, Spain.
Tel.: +34 94601596 8; fax: 946013500.
E-mail address: alazne.galdames@ehu.eus (A. Galdames).
m
f
l
w
i
http://dx.doi.org/10.1016/j.reffit.2017.03.008
2405-6537/© 2017 Tomsk Polytechnic University. Published by Elsevier B.V. This is an ope
( http://creativecommons.org/licenses/by-nc-nd/4.0/ )
he soil natural heterogeneity adds to this complexity. Soil prop-
rties such as texture, degree of structure development, water re-
ention capacity and/or chemical properties can be determinants
or the diffusion of contaminants, and more importantly, for their
egree of attachment to the soil mineral and organic matrix. This
an be positive when it results in reduced diffusion and high bio-
eo-chemical stabilization of pollutants in soils, but at the same
ime limiting when the goal is removing soil contamination. For
nstance, clayey soils rich in high-reactive silicates and/or contain-
ng pH-modifiers such as carbonates can retain easily degradable
rganic pollutants in primary and secondary organo-mineral com-
lexes, hindering their biological decomposition within the soil
atrix.
In this framework, contaminants in soils and sediments can be
ound in six different ways [1] : as particulate contaminants, as
iquid films, adsorbed, absorbed, dissolved in the interstitial pore
ater, or as solid phases in the pores. For each case, the behav-
or of the contaminant is different so its hazardousness must be
n access article under the CC BY-NC-ND license.
A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176 167
e
t
t
w
w
r
a
i
i
o
s
b
A
a
a
b
a
s
f
f
w
g
f
p
t
t
f
t
t
b
a
m
M
t
g
w
[
p
o
l
m
a
t
m
s
a
t
(
t
w
r
a
s
m
t
i
t
s
a
u
s
i
t
a
s
w
c
p
g
o
t
b
f
g
s
t
t
n
i
v
p
o
a
b
a
a
t
c
t
t
s
t
t
a
a
s
t
o
a
t
e
t
i
o
d
a
s
d
l
u
s
i
t
i
u
e
a
n
r
t
p
p
s
b
t
valuated on the basis of its mobility and availability, which is de-
ermined by different chemical and mineralogical procedures. In
he case of heavy metal pollution in soils, which poses a world-
ide challenge, their mobility can be evaluated extracting the
ater-soluble fraction of the metal. This fraction measurement rep-
esents an approximation to the amount of metals that plants can
bsorb from the soil under normal conditions [2] . The availabil-
ty of a metal depends, as that of organic pollutants, on its chem-
cal speciation and on a number of soil parameters such as pH,
rganic matter concentration, clay mineral carbonates, etc. For in-
tance, the availability of any exchangeable cation is conditioned
y the associated minerals that form the exchange complex. Thus,
s, in its oxidized form, especially at acid-neutral pH, is chemically
dsorbed to oxides of iron and aluminum, aluminosilicates and, to
lesser extent, sheet silicates. In sodium soils, arsenic is more mo-
ile and is released from the solid phase to soil dissolution, such as
rsenate anion. In reducing environments, As is in the form of ar-
enite anion, which is still absorbed by the clay fraction with more
orce than the anion arsenate. This results in As (III) being mani-
estly more toxic than As (V), since it forms very stable complexes
ith the SH groups of the enzymes. The oxidative capacity of man-
anese oxides is sufficient to oxidize the arsenite to arsenate. As
ar as Cr is concerned, it is found in the natural environment, es-
ecially in tri- and pentavalent forms. The trivalent form gives rise
o very stable complexes with organic and inorganic ligands con-
aining oxygen or nitrogen atoms. In the soil, this metal can be
ound to several depths. In general, normal soil conditions favor
he Cr (III) form, which remains quite immobile, being retained on
he surface of oxides and silicates, where it forms stable chemical
onds even at acid pH. At pH above 5, Cr(OH) 3 is precipitated as
n hydroxide. In higher pH media, Cr (III) can be oxidized to chro-
ate anion, CrO 4 2 −, which is the toxic form of Cr. The presence of
n oxides favors this oxidation. The Cr (VI) species is more mobile
han Cr (III), especially in the presence of organic matter. The or-
anic matter acts as reducing agent, and, in addition, it complexed,
hich favors the retention of the Cr (III) produced in the reaction
3] .
Organic pollutants are also widespread in brownfields and other
olluted sites in industrial and peripheral areas worldwide. They
ccur as byproducts and residues or spills of the chemical, metal-
urgical and other industrial activities, and include a wide range of
olecules containing C and at least one C
–H group. Many of these
re the result of liberation of human-made organic components
o the environment. On average, 260 Tg of organic compounds are
anufactured annually only in the US. Oil byproducts are the most
ignificant source of hydrocarbons into the environment, usually
ssociated with the use of oil-derived fuels [4] .
One class of organic pollutants which has gained great atten-
ion in environmental studies is polycyclic aromatic hydrocarbon
PAH). PAHs have high resonance energies as a consequence of
heir dense clouds of pi electrons surrounding the aromatic rings,
hich make them persistent compounds in the environment and
ecalcitrant to degradation [5] . This molecular structure is char-
cterized by their hydrophobicity so that they display decreasing
olubility in water with increasing molecular mass. The environ-
ental fate of PAHs depends largely on the environment to which
hey are exposed. The phase or state of a PAH is determined by
ts vapor pressure and room temperature. Experiments have shown
hat, at 25 °C, four- and five-ring PAHs are distributed between the
olid phase and steam, while PAHs with six and more rings are
lmost exclusively in the solid phase [6] . PAHs with high molec-
lar weights (from four benzene rings) are more likely to be ab-
orbed to the soil organic matter, and therefore their availability
s reduced, but this also makes them less susceptible to remedia-
ion [7] . The fate and transport of PAHs is led by physical, chemical
nd biological processes that are influenced by the nature of the
ubsurface environment. Hence, several techniques have been used,
ith varying results, to achieve acceptable degradation of these re-
alcitrant compounds (e.g., chemical degradation, biodegradation,
hytodegradation and combined degradation methods).
Soil bioremediation is based on the biological degradation of or-
anic pollutants, ideally until their final transformation to CO 2 , in-
rganic compounds and/or other organic compounds with reduced
oxicity. Microorganisms able to degrade hydrocarbons in soils are
acteria, fungi and algae, bacteria being those with the highest and
astest degradation rates [8,9] . Average contents of these microor-
anisms in polluted soils are usually higher than in non-polluted
oils [10] . The success of bioremediation techniques depends on
he environmental conditions, number and type of organisms, and
he type and structure of the pollutants [8] . Bioremediation tech-
iques are usually based on the stimulation of the natural abil-
ty of soil microorganisms to degrade organic pollutants by fa-
oring their activity. This is generally done by granting adequate
hysical–chemical conditions (nutrients and water availability, aer-
bic conditions, right pH and red-ox characteristics) [11] and/or by
dding exogenous microbial populations especially competent for
iodegradation of the targeted pollutants. The addition of organic
mendments such as compost is a frequent strategy in this sense
nd has been used in many sites and contexts [12–14] . In addi-
ion, the pre-incubation of small quantities of the polluted soil in
ontact with this amendment favors the development of the na-
ive microbial populations able to degrade pollutants present in
he soil. This is known as assisted bioremediation including bio-
timulation.
Currently the most widely used techniques for soil remedia-
ion are based on the application of different physical and chemical
reatments. Lack of knowledge to properly assess new approaches
nd technologies tend to please the technologies that have been
lready proven successful in previous cases, and therefore the clas-
ical approach “dig and dump” is still hegemonic. At the same
ime, there is an inertia to extract the contaminated soil and carry
ut external treatments, which requires the processing of large
mounts of contaminated soil resulting in high costs and making
he control of the treatments difficult.
The synergistic use of nZVI and bioremediation is a new strat-
gy for restoring contaminated sites by the onsite application of
wo combined advanced technologies that can contribute to the
mplementation of recovery alternatives that reduce the volume
f waste generated in decontamination processes and therefore re-
uce the industrial impact on the environment.
Iron nanoparticles perform like strong reducing agents. Their
ction mechanism involves oxidation–reduction reactions (redox),
o that in contact with the medium they are oxidized rapidly and
onate their electrons to pollutants, thus reducing them. The pol-
utants become more stable, less mobile and/or less toxic prod-
cts. Among the advantages associated with the use of nZVI for
oil decontamination, there is the prospect of a notable reduction
n the ratio of kg of product per volume of soil to be treated,
hanks to the large surface area provided by nanomaterials regard-
ng macroscopic materials. The granular zero valent iron has been
sed for years with success, especially in permeable reactive barri-
rs (PRBs) for the treatment of chlorinated hydrocarbons (ethanes
nd ethenes), metals and metalloids (arsenic, chromium and ura-
ium), nitroaromatics, and treatment of perchlorates with limited
esults [15] .
There is a dearth of studies about the decontamination poten-
ial of nZVI in soils [16] . The treatment of the metals by nZVI is
roduced via immobilization [17] . This strategy prevents its trans-
ort through the layers of soil, rivers and groundwater. So far, the
tudies about the immobilization of metals by nZVI in soils have
een conducted in “in vitro” conditions. Some of the most impor-
ant trials have demonstrated the immobilization of Pb and Zn in
168 A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176
s
b
c
(
o
c
a
o
a
d
s
i
(
a
l
t
c
s
o
c
I
d
c
n
t
m
w
r
t
i
v
T
f
o
2
m
b
g
o
m
b
a
t
1
m
m
i
a
2
a
o
i
b
6
l
nZVI-treated soils through the analysis of the leachate [18] , as well
as some promising results have been obtained for reducing the
mobility of arsenic [19] , antimony [20] and some other metals and
metalloids in contaminated soils.
Uncertainty about the long-term fate, transformation and eco-
toxicity of nZVI in environmental systems is revealed as an impor-
tant point. It is necessary to predict the fate and physical, chem-
ical and biological consequences of the use of nZVI when used
in contaminated sites. Nanoparticles raise fear for their ability to
penetrate into the food chain (bioaccumulation), and also by the
possibility of facilitating the spread of other non-target pollutants
present in the soil [21] . Therefore, a better understanding of the
behavior of nanomaterials in sediments and soils, and its degree of
toxicity is necessary.
The use of compost in the process of biostimulation in assisted
bioremediation strategies is frequent. It grants a source of nutri-
ents and organic matter to stimulate microbial growth in contami-
nated soils with low natural fertility. When the compost used with
this aim is made from waste such as sewage sludge or other or-
ganic wastes, it has the advantage of meeting two objectives si-
multaneously: reducing soil contamination and giving a valuable
use to these wastes. The combination of chemical (iron nanopar-
ticles) and biological (bioremediation) technologies is intended to
optimize the cost-efficiency of soil remediation from three points
of view mainly: it can economize the process, reduce the time
for decontamination, and ensure the sustainability of process. This
requires a chemical intervention dimensioned so that a rapid re-
duction in the concentration of target pollutants occurs and thus,
a more effective bioremediation and a reduction in time of the
global treatment. Simultaneously, bioremediation can provide an
early use of the site as it can be compatible with the development
of certain activities on the site. Similarly, monitoring the chemi-
cal activity process ensures sustainability, as it reduces the use of
chemicals that can sometimes be aggressive for the soil and affect
its normal functions.
In short, this approach aims to provide solutions for a more ef-
ficient treatment and, therefore, more competitive, not only eco-
nomically but in recovery times, potential side effects, and the sus-
tainability of the application.
The objective of this work was to test the efficiency of a com-
bined technique of soil remediation, using an approach that cou-
ples classical bioremediation with organic amendments and the
use of zero-valent iron nanoparticles. The work was conducted in
two different soils (one artificially polluted with heavy metals and
hydrocarbons and one from a brownfield containing a complex mix
of organic and inorganic pollutants).
2. Materials and methods
2.1. Chemical reagents, standards and materials
2.1.1. Soils and compost
Two different soils were used for the assays of decontamina-
tion by the combined technique: Soil I came from a brownfield in
Barakaldo (North of Spain), and it was selected because of its high
concentration of hydrocarbons. Soil II, a natural soil from Azkoitia
(Spain) without known contamination, was also sampled. Soil II
was artificially contaminated, following a preset design and calcu-
lations, adapted to the objectives of the assays. The process of con-
trolled contamination was performed by adding diesel, potassium
dichromate and sodium arsenate to Soil II. To calculate the target
concentrations, the dry weight of the screened soil was considered
(487.6 kg of dry soil). These concentrations were established based
on the VIE B reference values of the regional Basque Law 4/2015
for the prevention and correction of soil contamination, seeking to
overcome these values.
Both soils were initially screened by a metal net 1 × 1 cm in
ize, obtaining the following amounts of soil available for the
iopiles: Soil I = 212,8 kg (ww); Soil II = 688,1 kg (ww).
Due to its high availability, MSW (municipal solid waste)
ompost was obtained from Garbiker Bizkaiko Konpostegia plant
Bizkaia, Spain). This compost was obtained from the municipal
rganic fraction, collected separately. It had a relatively high salt
ontent and a lower C/N ratio than recommended for bioremedi-
tion. The chemical characteristics of both soils (concentrations of
rganic C, total N, available P and K), and the compost, as well
s their physical characteristics (water retention capacity and bulk
ensity) were determined following the standard procedures for
oils [22] and are shown in Table 1 .
Soil I had a basic pH, a high concentration of soluble salts (typ-
cal of a marshy soil) and a suitable C/N ratio for bioremediation
recommended C/N ratio for bioremediation is 10) [23–25] . Soil II
lso had a basic pH, but a low concentration of soluble salts and a
ower C/N ratio than recommended ( Table 1 ).
Soil texture, a known factor determining the soil hydric proper-
ies, was also measured for Soil I and Soil II. Soil I had a high sand
ontent (74.5%) and low clay content (5.14%), resulting in a loamy
and texture, according to USDA soil texture classification. On the
ther hand, the artificially contaminated soil (Soil II) had a high
ontent of silt (58%), resulting on a silt loam texture.
The chemical analysis of the metals in soil was performed by
CP-MS (spectrometer with inductively coupled plasma with mass
etector Agilent 7700) and ICP-OES (spectrometer with inductively
oupled plasma with an optical detector). Samples were homoge-
ized and after that they were mineralized with aqua regia prior
o analysis. Digestion of the soil samples was performed in a CEM
icrowave under the EPA standard 3051_8, 0.5 g of sample was
eighed and digested with 9 mL of HNO 3 plus 3 mL of HCl. The
esulting extract was filtered and flushed to 50 mL. The leaching of
he soil samples extracted from the piles was carried out follow-
ng the instructions of the standard UNE-EN 12457-4 which pro-
ides a standard method for leaching granular waste and sludge.
his is a two-stage batch test with a solid–liquid ratio of 10 l/kg
or materials with a particle size of less than 10 mm. The leaching
f the samples was carried out with a roller stirrer at 10 rpm for
4 h and the filtering of the samples was performed with 0.45 μm
embrane filters.
Also aliphatic and aromatic fractions of petroleum hydrocar-
ons, and TPH or total petroleum hydrocarbons were analyzed by
as chromatography with FID and MS detection, as well as 16 PAHs
r polycyclic aromatic hydrocarbons were analyzed by gas chro-
atography with MS or MS/MS detection.
The preliminary analytical results showed a high uncertainty
ecause of the heterogeneity in the composition of the soil. To
void this fact, a sampling procedure was designed and applied
o ensure better uniformity, based on the standard UNE-EN 932-
. Thus, for the analysis, three samples of each soil were collected,
ade up of 15 aleatory points. Each sample was around 8 kg of
ixture (near 0.5 kg per point), thoroughly mixed and divided
nto 4 quarters to take the necessary amount for the chemical
nalysis.
.1.2. Commercial zero-valent iron nanoparticles
NANOFER 25S commercial nanoparticles were manufactured
nd supplied by NANOIRON (Rajhrad, Czech Republic). This kind
f nanoparticles offers a better balance between reactivity, stabil-
ty and dispersion.
The product was supplied as an aqueous dispersion, containing
y weight: 77% of water, 14–18% zero-valent iron nanoparticles, 2–
% iron oxides, 0–1% carbon and 3 % surfactant (PAA based stabi-
izer and coating).
A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176 169
Table 1
pH, electrical conductivity, nutrient content, moisture, water content at field capacity and wilting point (w.p.) of the soils and the compost.
Sample pH EC (1:5) (mS/cm) K (mg/kg) (dw) P (mg/kg) (dw) N (%) C (%) C/N Moisture (%) Field capacity (g/g) w. p. (g/g)
Soil I 8.74 1.920 197.3 6.22 0.38 4.18 11.0 15.5 0.25 0.11
Soil II 7.5 0.113 46.8 4.65 0.17 1.29 7.62 22.1 0.33 0.17
Compost MSW 8.2 4.23 14,904 318 2.5 20.3 8.12 22.1 0.91 0.63
2
i
p
t
o
T
2
p
m
w
a
n
a
w
w
a
S
(
1
i
t
c
p
i
T
s
t
t
i
i
c
m
o
b
l
d
t
c
i
w
e
t
d
4
s
a
7
o
r
p
u
c
i
s
3
i
t
i
t
a
i
t
l
S
P
a
o
c
t
d
i
t
a
t
o
a
T
2
m
m
w
g
r
a
w
t
n
n
s
t
s
a
f
o
m
t
p
s
s
f
f
.1.3. Site conditioning
The soil remediation assays were conducted at Iragaz facilities
n Azkoitia (Spain). Before performing the assay a safety basin was
repared to protect the assay from any eventuality. The floor of
he basin was sealed with a HDPE sheet to prevent the infiltration
f leachates into the subsoil and throughout the wall of the basin.
ents were also set up to protect biopiles from precipitation.
.2. Preincubation, biopile formation and monitoring
The trials were set up in a sequence with three steps based on
revious experiences.
First, the two soils were conditioned as described above, and
ixed with zero-valent iron nanoparticles. The nanoparticles used
ere previously characterized, showing a high degree of dispersion
nd low sphericity, and a large crystalline iron content and mag-
etite was observed in X-ray diffractograms (see TEM micrographs
nd x-ray diffractograms in [26] ). The mixture of Soil I and Soil II
ith nanoparticles was performed by adding 1% of slurry on the
eight of wet soil. The mixture was allowed to react for 72 h, and
nother 1% slurry was subsequently added.
The process in each addition of nanoparticles was monitored.
amples were taken stack according to the UNE-EN 932-1 Standard
Testing to determine the general properties of the aggregates, Part
: Sampling Methods), and extracted samples were leached accord-
ng to UNE-EN 12457-4 and later analyzed for the determination of
otal concentration of As, Cr and Fe in each stage of the process.
Second, a subsample of the two soils was pre-incubated with
ompost. This was done on the basis of the results of previous ex-
eriments in order to allow a better development of microorgan-
sm populations native to both soils able to degrade hydrocarbons.
he presence of this type of microorganisms is common in these
oils. Pre-incubation implies inoculating a small sample of soil to
he compost and adjusting temperature, water contents and nu-
rients to optimal conditions for their development. The availabil-
ty of C from compost implies that these microorganisms can grow
n non-limiting conditions. The development of these populations
ould allow a better degradation of soil hydrocarbons promoting a
ore effective bioremediation in the final biopiles. The mixing rate
f compost and soil for the incubation was 80–20 on a dry mass
asis, for the total amount of compost used in the biopiles (see be-
ow). The mixing was done mechanically to ensure a homogeneous
istribution of soil in the compost. Water was added to ensure wa-
er availability at 70% of the field capacity of the mix. The total
ontents of C, N, available K and P were controlled, and remained
n non-limiting ranges for microbial growth. The pre-incubation
as conducted for two weeks. Temperature was controlled daily to
nsure adequate conditions (20–25 °C), and the piles were aerated
wice a week by mechanical means.
Finally, using the pre-incubated compost, biopiles for bioreme-
iation were set. The final soil–compost proportion was 52.9%–
7.1% (dry mass basis) for Soil I and 54.3%–45.7% for Soil II. Both
oils had been previously mixed with nanoparticles as described
bove. Water was added to ensure water retained content between
0% and 100% of the field capacity in each mix. The content of
rganic C, total N and available P was monitored and verified to
emain in a proportion of 100:10:1 during all the bioremediation
rocedures.
The biopiles were set in open-air cells to better simulate nat-
ral conditions. They were protected from rainfall to avoid ex-
ess moisture that could hinder microbial activity, and the exper-
ment was run for 66 days. Temperature was measured daily at
everal points of each biopile and remained within a range of 20–
5 °C. Biopiles were aerated by mechanical mixing to avoid the ex-
stence of anaerobic conditions. Water was added when needed
o ensure adequate moisture conditions (70–100% of field capac-
ty). The decontamination process was monitored by sampling the
wo biopiles in triplicate using the protocol described above, and
nalyzing the biopiles at day 0, and at the end of the exper-
ment (day 66). In each sampling, aliphatic and aromatic frac-
ions of petroleum hydrocarbons, TPH and 16 PAHs were ana-
yzed. Those analyses of contaminants were done as described (see
ection 2.1.1 ).
A triplicate analysis of the concentration of hydrocarbons and
AHs in compost was also performed before mixing with soils. An
verage of 104.3 mg/kg of TPH ( > C10–C40 Fraction) and 2.25 mg/kg
f the sum of 16 PAHs were obtained.
When the concentration of a contaminant (in this case, a hydro-
arbon) falls to non-toxic limits according to the legislation only by
he action of the microorganisms present in the soil, the process of
econtamination is described as natural attenuation . Soil I was left
n optimal conditions for natural attenuation for 16 months before
he start of the experiment reported in this work. This implies that
ny possible natural reduction of the concentration of pollutants in
his soil was finished before the biopiles were set up. The results
btained demonstrated that natural attenuation did not result in
ny significant reduction of the concentration of contaminants (see
able S1 ).
.3. Toxicity
Ecotoxicity tests of the biopiles (by “Eisenia foetida ” earthworm
ortality test according to OECD 207 [27] and “Linum usitatissi-
um sp.” plant seeds growth test according to OECD 208 [28] )
ere performed in the initial contaminated soils and in the be-
inning and the end of the biopiles in accordance with the legal
ecommendations of the Spanish Royal Decree 9/2005.
These tests were performed in order to verify that the aver-
ge lethal or effective concentration (LC50) of the soil samples was
ithin the values established in Royal Decree 9/2005, as well as
o evaluate the evolution of toxicity throughout the decontami-
ation treatments. According to Spanish law, the soil is contami-
ated when the average lethal or effective concentration LC50 for
oil organisms is less than 10 g of contaminated soil/kg of con-
rol substrate. For that purpose, according to the regulations de-
cribed in the OECD 207 and OECD 208 standards, selected worms
nd seeds were exposed to samples of contaminated soil at dif-
erent concentrations on an artificial substrate (control) to finally
btain LC50 or concentration of contaminated soil from which the
ortality is higher than 50% of the individuals (case of earthworm
ests) or the concentration of contaminated soil from which the
ercentage of non-germinated seeds is higher than 50% (case of
eeds growth tests). In the case of earthworm toxicity tests, the as-
ays were performed with adult individuals of the species “Eisenia
oetida ”, disease-free, cultivated in the laboratory and kept in re-
rigerated stove at 20 °C with light exposure (600 lux) for 14 days.
170 A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176
Table 2
Initial average concentration of hydrocarbons, heavy metals and other pollutants (mg/kg) of the soils used in the study. Underlined values indicate values above the limits of
Industrial VIE B (Basque Law 4/2015).
Chemical parameter Soil I Soil II Chemical parameter Soil I Soil II
As 47.3 244 Naphthalene 159 1.5
Cd 4.5 < 0.40 Phenanthrene 701 2.7
Cr 31.4 52.7 Pyrene 731 2.0
Cr (VI) 0.35 1.11 Sum of 16 PAH 6737 12.1
Cu 315 23.3 TPH > C10–C40 fraction 16533 11033
Pb 1162 35.8 > C10–C40 Aliphatic fraction 962 8197
Hg 15.7 < 0.20 > C10–C12 Aliphatic fraction 42 709
Mo 10.6 0.5 > C12–C16 Aliphatic fraction 73.1 2840
Ni 53.4 32.1 > C16–C21 Aliphatic fraction 129 3160
Zn 2710 101 > C16–C35 Aliphatic fraction 710 4640
Acenaphthene 124 0.5 > C21–C35 Aliphatic fraction 581 1480
Acenaphthylene 0.5 0.1 > C35–C40 Aliphatic fraction 138 4.5
Anthracene 225 0.4 > C6–C8 Aliphatic fraction < 5.0 < 5.0
Benz(a)anthracene 754 0.4 > C8–C10 Aliphatic fraction < 5.0 73.4
Benzo(a)pyrene 556 0.4 > C10–C12 Aromatic fraction 142 126
Benzo(b)fluoranthene 772 0.7 > C10–C40 Aromatic fraction 15567 2840
Benzo(g.h.i)perylene 211 0.3 > C12–C16 Aromatic fraction 545 874
Benzo(k)fluoranthene 291 0.2 > C16–C21 Aromatic fraction 3937 1137
Chrysene 676 0.4 > C21–C35 Aromatic fraction 9967 697
Dibenz(a.h.)anthracene 83.1 0.1 > C35–C40 Aromatic fraction 994 5.8
Fluoranthene 1043 0.7 > C7–C8 Aromatic fraction 0.3 0.2
Fluorene 130 1.3 > C8–C10 Aromatic fraction < 0.80 11.2
Indeno(1.2.3.cd)pyrene 283 0.3 C6–C7 Aromatic fraction 0.2 < 0.120
t
[
t
a
s
v
o
T
(
t
3
i
t
o
t
n
1
e
c
t
p
a
a
i
i
t
a
n
i
w
t
e
e
i
After the 14 day period, the substrate of each test was evaluated
to observe the worms and determine the number of survivors. The
weight of the worms was also considered in order to assess the
loss of biomass. In the case of emergence and seeds growth, guar-
anteed seeds of “Linum usitatissimum sp.” were used and the tests
were carried out at different concentrations of contaminated soil
in a germination and growth chamber, at 23 ± 2 °C, and a relative
humidity of 70 ± 20% for 14 days. After this period the percentage
of non-germinated seeds and the length of radicle and hypocotyl
were evaluated in each test.
2.4. Statistical analysis
For the bioremediation assays, data are presented as ±standard
error of the mean for the results of the different parameters
studied. Comparison between biopiles was carried out by using
the univariate linear model (ANOVA). Significant differences were
based on a probability level of P < 0.05 unless otherwise indicated.
All statistical analyses were performed using the SPSS 18.0 soft-
ware (SPSS Inc., 2009). The data obtained from the assays with
nanoparticles are presented as ±standard deviation of the mean
values obtained from the analyses of three replicates of each ana-
lyte.
3. Results and discussion
3.1. Characterization of soil contamination
Both soils were characterized at the beginning of the experi-
ment, with two aims: First, assessing the presence of contaminants
in Soil I (from a brownfield), after a period of natural attenuation.
Second, determining the most significant contaminants in Soil I in
order to design the procedure for artificially contaminating Soil II.
The results of these analyses are shown in Table 2 .
In the case of Soil II, the objective was to get an experimen-
tal soil with a different contamination than Soil I, so a natural soil
was artificially contaminated. As Soil I had a high content of PAH,
a predominantly aliphatic hydrocarbon was selected as target con-
taminant for Soil II, to be addressed by bioremediation. Commer-
cial diesel was added in the proportions needed to attain a con-
centration of hydrocarbons similar to that present in Soil I. To fur-
her test the ability of nZVI to immobilizing metalloids such as As
29–32] and to reduce metals such as Cr (VI) to Cr (III) [33] , these
wo toxic species were selected as well.
Soil I and Soil II after being artificially contaminated were an-
lyzed in triplicate to obtain an accurate characterization. The two
oils had high concentrations of total hydrocarbons; Soil I also had
ery high concentrations of PAHs and Pb. Soil II had a high content
f As; however, the design values were not obtained for Cr (VI) and
PH (C10–C40). This is attributed to the reduction of Cr (VI) to Cr
III) by reaction with the organic matter in soil and possibly with
he hydrocarbons of the diesel added.
.2. Monitoring of the nanoparticle treatment for metal adsorption
The adsorption of Cr and As was monitored at different stages
n order to determine the effectiveness of the immobilization of
hese metals during the time of treatment with nZVI. The results
btained from the concentration measures of both metals in soil in
he different phases (at the first stage with the addition of 1% of
ZVI in slurry format and after 72 hours with the addition of other
% of nZVI) are summarized in Table S2 .
Initially both soils had a high iron content, which consequently
xperienced an increase in its concentration by adding nZVI. The
oncentration of Cr and As remained unchanged because the de-
ermined concentrations were total concentrations of the metal
resent in soil. The metal adsorption by nZVI does not change the
mount of metal present in soil, but nevertheless, it reduces its
vailability and its diffusion capacity.
As shown in Fig. 1 , bar charts showed an elevated dispersion
n the results for chemical concentrations of Cr in Soil I and As
n Soil II, probably due to the different homogeneity of the mix-
ure of contaminants with Soil I (from contaminated industrial site)
nd Soil II (artificially contaminated). The diffusion of contami-
ants through the soil depends largely on the own hidrogeochem-
cal characteristics of each soil [3] .
The metals’ ability to spread depends on whether the metal is
ater-soluble. Therefore, in order to evaluate the effectiveness of
he treatment with nanoparticles in immobilizing As and Cr, sev-
ral replicates of each soil leached were analyzed in the differ-
nt phases of nZVI addition. The leaching of contaminants present
n soil is controlled by different parameters and external factors,
A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176 171
Fig. 1. Evolution of Cr and As concentrations in soil I and soil II in different phases of the treatment with iron nanoparticles. Bars indicate the standard deviations of the
means of three replicates of each sample.
Fig. 2. Bar graph of the mean values of Cr and As concentrations in leachates obtained from three replicates of each sample of Soil I and two replicates of each sample of
Soil II and concentration of Cr and As determined for two replicates of Soil II after leaching in the different phases of the treatment. Bars indicate standard deviation of the
mean of several replicates of each sample.
i
c
t
t
e
l
s
t
a
t
i
m
m
a
ncluding the chemical nature of the soil (pH, reduction properties,
ontent degradable organic material), the nature of leachant, and
he contact time of leachant with the soil. Therefore, pH, conduc-
ivity and temperature of leachant and leachate were monitored at
ach stage of the process ( Table S3 ).
The average values of concentration of Cr and As in the
eachates of each soil in the different stages of the treatment are
hown in Table S4 .
For Cr and As in Soil I and Soil II was observed a trend toward
he reduction of the concentration of both analytes in the leachate
fter adding 2% of nZVI. As can be seen ( Fig. 2 ) the reduction of
he concentration in the leachate in the case of Soil II produced an
ncreased of the presence of the two metals in the same soil re-
aining after being leached. The concentrations obtained for each
etal in soil and leachate are shown in Tables 3 and 4 , as well
s the percentage of metal leached. Thecalculation method of the
172 A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176
Table 3
Cr percentage obtained in the leachate (Leach) of the different phases of the treatment in relation to the Cr concentration determined in soil samples (mean ± standard
deviation of the concentration values of soil and leachates).
Sample mg Cr /kg Soil I mg Cr /L Leach I %Cr Leach I Sample mg Cr /kg Soil II mg Cr /L Leach II %Cr Leach II
SI inic. 34.8 ± 12.2 0.0030 ± 0.0004 0.009 SII inic. 61.9 ± 3.3 0.1100 ± 0.000 0.177
SI 1% NP 34.2 ± 2.9 0.0059 ± 0.0040 0.017 SII 1% NP 61.2 ± 3.9 0.1250 ± 0.020 0.204
SI 2% NP 33.7 ± 12.9 0.0018 ± 0.0003 0.005 SII 2% NP 67.8 ± 3.8 0.0375 ± 0.050 0.055
Table 4
As percentage obtained in the leachate (Leach) of the different phases of the treatment in relation to the As concentration determined in soil samples (mean ± standard
deviation of the concentration values of soil and leachates).
Sample mg As /kg Soil I mg As /L Leach I %As Leach I Sample mg As /kg Soil II mg As /L Leach II %As Leach II
SI inic. 46.1 ± 8.0 0.0065 ± 0.0005 0.014 SII inic. 231.2 ± 3.7 0.3850 ± 0.05 0.166
SI 1% NP 39.0 ± 2.1 0.0170 ± 0.0143 0.044 SII 1% NP 281.7 ± 39.5 0.4800 ± 0.00 0.170
SI 2% NP 43.2 ± 9.7 0.0034 ± 0.0002 0.008 SII 2% NP 274.7 ± 16.9 0.1900 ± 0.17 0.069
Fig. 3. Representation of the mean values of concentrations of Cr and As in the leachate for Soil I and Soil II through the initial phase of the treatment (addition of 1% of
nanoparticles), second phase (addition of 2% of nanoparticles) and third phase (addition of compost (BP final)). Bars indicate standard deviation of the three replicates of
each sample (except for the first two phases of Soil II that are two replicates for each sample). The standard deviation of the three replicates of concentration of Cr and As
of the biopiles can be seen in Table S6 .
s
p
a
g
c
w
c
percentage of leached analyte is contained in the Supplementary
material.
The percentage of each metal in the leachate with respect to
that contained in no-leached soil was evaluated. A reduction of the
percentage of As and Cr in the leachates could be observed in the
second phase of the treatment for Soil I and a similar trend was
observed for the Soil II samples. On the contrary, in the first stage
of application of nanoparticles, an increase on concentration val-
ues of both metals occurred. This fact suggests that initially, nZVI
hows a preference to react with other components of the soil that
roduce changes that probably involve the increase of the avail-
bility of metals in this stage.
To assess the synergistic action of the combination of technolo-
ies studied (nZVI and bioremediation with compost), Cr and As
oncentration in leachate of Soil I and Soil II after being mixed
ith compost was measured (BP I and BP II respectively).
As can be seen in Fig. 3 , an increase in As concentration oc-
urred in Biopile II compared to the concentration obtained for Soil
A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176 173
Fig. 4. Evolution of hydrocarbon concentrations (mg/kg) in the biopiles. BP I: Biopile I; BP II: Biopile II. Bars indicate standard error. ∗Significant differences, n = 3; P < 0.05.
I
b
c
o
b
n
a
3
t
t
c
a
c
s
a
e
f
e
s
b
C
c
s
c
c
l
t
c
t
t
Table 5
Percentages of reduction in % over the original soil concentration with observed
significant differences (n = 3; P < 0.05)
Biopile I Biopile II
Total hydrocarbons C10–C40 — −53%
Aliphatic hydrocarbons C10–C12 — −80%
Aliphatic hydrocarbons C10–C40 −60% −59%
Aliphatic hydrocarbons C12–C16 — −67%
Aliphatic hydrocarbons C16–C21 — −55%
Aliphatic hydrocarbons C16–C35 −55% −52%
Aliphatic hydrocarbons C21–C35 −46% −45%
Aliphatic hydrocarbons C35–C40 −56% —
Aliphatic hydrocarbons C35–C40 — −42%
Acenaphthylene — −58%
b
m
d
t
b
r
a
w
4
b
w
f
h
i
c
l
s
I before mixing with compost. This is probably due to the possi-
ility of interactions of the contaminants with compost that may
hange the behavior of the metals. Moreover, the immobilization
f metals by nZVI may be influenced by other aspects that must
e evaluated, as the stability of the immobilization. This fact could
ot be tested in the framework of this work but it needs to be
ssessed to improve the decontamination treatment.
.3. Evolution of hydrocarbons during bioremediation
The effectiveness of decontamination for hydrocarbons was
ested by measuring the concentration of total hydrocarbons and
heir fractions at the start and the end of the bioremediation pro-
ess, once the biopiles formed. To avoid misinterpretation or bi-
sing of the data because of the dilution effect in biopiles, these
oncentrations were corrected using the compost-to-soil ratios de-
cribed above. Fig. 4 represents the evolution of total, aliphatic,
romatic and PAHs in the two biopiles.
As it can be observed, a significant reduction of −53% on av-
rage was observed for total hydrocarbons only in BP II. No dif-
erences were however observed in BP I for this parameter. How-
ver, when the different families of hydrocarbons were studied
eparately, aliphatic chains showed significant decreases in both
iopiles ( Table 5 ). In particular, aliphatic chains in the range C16–
40 displayed reductions close to 50% in BP I and BPII, and shorter
hain concentrations were reduced up to 80% in BP II. These re-
ults suggest that the combined use of iron nanoparticles and
ompost bioremediation can be effective in significantly reducing
ontamination from aliphatic hydrocarbons, especially those with
onger chains. The lack of increment of the shorter chains indicates
hat this reduction was a true decomposition into non-hydrocarbon
ompounds. The type and fate of these compounds cannot be
ested in the framework of this work, but it can be assumed from
he type of process that they should include by-products of micro-
ial degradation, recalcitrant organic compounds associated to the
ineral matrix of the soil, and/or CO 2 , if their metabolical degra-
ation was complete. The toxicity of these compounds needs to be
ested to ensure an effective decontamination (see Section 3.3 ).
However, aromatic and PAHs remained almost unchanged for
oth biopiles, except for acenaphthylene in BP II, which showed a
eduction of 58% in its concentration ( Fig. 5 and Table 5 ). The prob-
bility that the initial and final samples of aromatic hydrocarbons
ere equal was 54% in BP I, 16% in the BP II and for PAHs it was
3% in BP I and 94% in BP II.
The unsuccessful decontamination in relation to PAHs can
e explained from different reasons. PAHs, which are highly
idespread in many industrial areas and pose a major concern
rom the environmental and public health perspectives [4,34] , are
ighly hydrophobic and biochemically recalcitrant. Both character-
stics determine their behavior in the environment [35] , as mi-
roorganisms can only degrade the fraction present in the soil so-
ution [36] . According to Bamforth and Singleton [37] the most
ignificant factors affecting PAH biodegradation are temperature
174 A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176
Fig. 5. Evolution of polycyclic aromatic hydrocarbon (PAH) concentrations (mg/kg) in the biopiles. BPI: Biopile I; BPII: Biopile II. Bars indicate standard error. ∗Significant
differences, n = 3; P < 0.05.
3
n
t
s
e
s
t
n
(
s
(20–45 °C), soil pH (6–8), oxygen concentration (aerobic conditions
required), nutrient availability (C:N:P ratios between 100:15:3 and
120:10:1), moisture conditions (70–100% field capacity), and the
own bioavailability of PAHs for microbial activity. Considering that
these parameters were kept within non-limiting ranges during the
process of bioremediation, and that biodegradation processes of
other compounds actually occurred within the biopiles ( Table 5 ), it
is likely that the adsorption of PAHs to mineral surfaces, or their
occlusion within the organo-mineral matrix of the soil played a
role in hindering their biological degradation. Considering the haz-
ardous nature of these compounds, improved bioremediation tech-
niques need to take into account this limitation.
.4. Toxicity evaluation
According to Spanish law (Royal Decree 9/2005), a contami-
ated soil is defined when the average lethal or effective concen-
ration LC50 for soil organisms is less than 10 g of contaminated
oil/kg of control substrate. Thus, the evolution of ecotoxicity was
valuated by determining LC50 values on the initial contaminated
oils (raw contaminated soils) and on the beginning and the end of
he treatment in biopiles, i.e. at the beginning of the application of
anoparticles and compost (t = 0) and at the end of the treatment
t = 66 days). It was observed that initially the two contaminated
oils had a moderate toxic nature, since they were below the legal
A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176 175
Table 6
Values of LC50 in the samples of the initial contaminated soils and in the beginning (t = 0) and the end (t = 66 days) of the treatment in biopiles (BP).
Sample
BP I (g/kg) BP II (g/kg)
Earthworm Seeds growth Earthworm Seeds growth
Soil 510 596 .5 460 .4 877 .2
BP initial (t = 0) 319 .7 874 .1 618 .0 936 .3
BP final (t = 66 days) 591 .2 909 .0 Not reached with 100% concentration Not reached with 100% concentration
LC 50: in the plant seeds growth test, it is the concentration of the test substance at which the change in emergence is 50% of that of the control. In the earthworm mortality
test it is the median lethal concentration, i.e. that concentration of the test substance which kills 50% of the test animals within the test period.
l
f
t
t
t
v
t
w
t
w
d
c
e
r
s
t
w
w
a
t
4
t
i
p
a
i
I
o
a
c
o
t
i
m
t
t
p
i
m
i
a
t
e
e
b
p
a
w
fi
a
A
(
A
T
s
t
B
a
e
A
d
R
imit of 10 g/kg. However by adding ZVI nanoparticles and compost
or the soil treatment in biopiles, samples behaved differently.
Results in Biopile I showed a decreasing toxicity of the mix-
ure for terrestrial plants, mainly reduced at the beginning of the
reatment, due to the dilution effect with the compost. During the
reatment, toxicity reduction was mild, although it remained at
ery low values. This low reduction of toxicity could be due to
he residual toxicity caused by certain recalcitrant contaminants,
hose toxicity was maintained over time. However, an increase in
oxicity was observed by adding compost in the test with earth-
orms, despite the dilution effect of pollutants should have re-
uced this toxicity. Only a comprehensive assessment of the bio-
hemical processes could provide more accurate information; how-
ver, it is possible that this increase in toxicity was caused by these
easons:
a) The mixture of the contaminated soil, compost and nZVI drove
to an increase of microbiological and biochemical processes, re-
sulting in intermediate compounds of greater toxicity, which
led to an increased toxicity in the mix.
b) As occurred with the As in Biopile II, the addition of compost
could cause an increase in the bioavailability of Pb so that it
could enter the metabolic pathways of living organisms more
easily than in the initial contaminated soil. Bioavailability is a
transcendental in the definition of toxicity of a specific pollu-
tant factor.
During the treatment a further ecotoxicity reduction was ob-
erved in the earthworms, reaching final values close to those of
he initial soil ( Table 6 ).
In the case of Biopile II, a significant reduction of ecotoxicity
as observed throughout the process, not reaching the LC50 even
ith 100% of the sample after the treatment, in both earthworm
nd seeds growth tests. This reduction could be possibly related to
he decrease in the concentration of aliphatic hydrocarbons.
. Conclusions
This study shows that the application of nZVI for immobiliza-
ion of As and Cr in two different soils – Soil I (from a contam-
nated industrial site) and Soil II (contaminated artificially) – can
rovide an effective method to reduce the concentration of these
nalytes in the leachate in successive applications of nZVI, show-
ng a tendency to decrease Cr and As specially in leachate of Soil
I. The results obtained are not conclusive because the dispersion
f the concentrations of both analytes does not allow an objective
nalysis of the data.
As observed, the synergistic action of the nanoparticles and
ompost had as an effect a strong increase of the concentration
f As in the leachate, mainly in Biopile II, well above the concen-
ration of this metal found in the leachate of the untreated soil (S
nitial). The obtained results suggest that the stability of the treat-
ent and the interactions of metals with the components of the
wo different soils and compost must be evaluated in the future.
On the other hand, the addition of MSW compost and nanopar-
icles under uncontrolled environmental conditions was able to
roduce a decrease in the concentration of aliphatic hydrocarbons
n the two biopiles up to 60%. Especially degradation and transfor-
ation of longer chains occurred. However a significant decrease
n the concentrations of aromatic hydrocarbons and PAHs was not
chieved in the two assays.
Similarly, a significant reduction of ecotoxicity was observed
hroughout the process in the biopile II, not reaching the LC50
ven with 100% of the sample after the treatment at the end of the
xperiment, in both earthworm and seeds growth tests. Results in
iopile I showed a decreasing toxicity of the biopile for terrestrial
lants, mainly reduced at the beginning of the treatment. However,
n increase in toxicity was observed by adding compost in the test
ith earthworms.
In conclusion we believe that the proposed methodology can
nd a valuable application in the utilization of nZVI and compost
s a new strategy for restoring contaminated sites.
cknowledgments
The authors thank the University of the Basque Country
UPV/EHU) for the technical and human support provided by the
nalytical Research Service (SCAB) from SGIKER of the UPV/EHU.
he authors gratefully acknowledge Iragaz partnersfor trusting and
upporting this study. Also, the authors thank administrations
hat collaborate to carry out this project: CDTi, Gaitek, Spri and
urtzeña Enpresa Parkea. The collaboration of C. González in the
nalytical determinations of soils and composts is also acknowl-
dged.
ppendix. Supplementary material
Supplementary data to this article can be found online at
oi: 10.1016/j.reffit.2017.03.008 .
eferences
[1] W.H. Rulkens , J.T.C. Grotenhuis , R. Tichy , Methods of cleaning contaminated
soils and sediments, in: W. Salomons, U. Förstner, P. Mader (Eds.), Heavy Met-als, Springer-Verlag, Berlin, 1995, pp. 165–191 .
[2] F.R. Siegel , Environmental Geochemistry of Potentially Toxic Metals,Springer-Verlag, Berlín, 2001 .
[3] X. Domènech , J. Peral , Química Ambiental de sistemas terrestres, Reverté,
Barcelona, 2006 . [4] G.M. Pierzynsky , J.T. Sims , G.F. Vance , Soils and Environmental Quality, third
ed., Taylor & Francis, USA, 2005 . [5] A.R. Johnson , L.Y. Wick , H. Harms , Principles of microbial PAH-degradation in
soil, Environ. Pollut 133 (2005) 71–84 . [6] G.M. Maria Jesús , Los hidrocarburos policíclicos aromáticos asociados a com-
bustibles fósiles. Caracterización, análisis y remediación Tésis Doctoral, Depar-tamento de ingeniería química y combustibles, Escuela Técnica Superior de In-
genieros de minas, Spain, 2005 .
[7] C.E. Cerniglia , M.A. Heitkamp , Microbial Degradation of Polycyclic AromaticHydrocarbon (PAH) in the Aquatic Environment, second ed., CRC Press, Boca
Raton, USA, 1989, pp. 41–68 . [8] A.K. Haritash , C.P. Kaushik , Biodegradation aspects of polycyclic aromatic hy-
drocarbons (PAHs): a review, J. Hazard. Mat 169 (2009) 1–15 .
176 A. Galdames et al. / Resource-Efficient Technologies 3 (2017) 166–176
[
[
[
[9] S. Lladó, Biorremediación de suelos contaminados por hidrocarburos pesadosy caracterización de comunidades microbianas implicadas Tesis Doctoral, Uni-
versidad de Barcelona España, 2012 . [10] A.R. Izquierdo , Biodegradación de HAPs durante la biorremediación aeróbica de
suelos contaminados con hidrocarburos del petróleo. Análisis de poblacionesbacterianas y genes funcionales Tesis Doctoral Universidad de Barcelona, Es-
paña, 2013 . [11] W. Chang , A. Akhari , J. Snelgrove , D. Frigon , S. Ghoshal , Biodegradation
of petroleum hydrocarbons in contaminated clayey soils from a sub-arctic
site: the role of aggregate size and microstructure, Chemosphere 91 (2013)1620–1626 .
[12] H.I. Atagana , Compost bioremediation of hydrocarbon-contaminated soil inoc-ulated with organic manure, Afr. J. Biotechnol 7 (10) (2008) 1516–1525 .
[13] T. Sayara , E. Borràs , G. Caminal , M. Sarrà, A. Sánchez , Bioremediation of PAH-s-contaminated soil through composting: influence of bioaugmentation and
biostimulation on contaminant biodegradation, Int. Biodeterior. Biodegradation
65 (2010) 859–865 . [14] JRC. , Remediated sites and brownfields. Success stories in Europe EUR 27530
EN, 2015 doi:102788/406096 . [15] P.G. Tratnyek , R.L. Johnson , Nanotechnologies for environmental cleanup, Nano
Today 1 (2006) 44–48 . [16] C. Fajardo , M. Diaz-Gil , G. Costa , J. Alonso , A.M. Guerrero , M. Nande , et al. ,
Residual impact of aged nZVI on heavy metal polluted soils, Sci. Total Environ
535 (2015) 79–84 . [17] R.A. Crane , T.B. Scott , Nanoscale zero-valent iron: future prospects for an
emerging water treatment technology, J. Hazard. Mat 211-212 (2012) 112–125 . [18] M. Gil-Díaz , L.T. Ortiz , G. Costa , J. Alonso , M.L. Rodriguez-Membibre ,
S. Sánchez-Fortun , et al. , Immobilization and leaching of Pb and Zn in an acidicsoil treated with zerovalent iron nanoparticles (nZVI): physicochemical and
toxicological analysis of leachates, Water Air Soil Pollut 225 (2014) 1990 .
[19] M. Gil-Díaz , J. Alonso , E. Rodríguez-Valdés , P. Pinilla , M.C. Lobo , Reducing themobility of arsenic in brownfield soil using stabilised zero-valent iron nanopar-
ticles, Environ. Sci. Health A 49 (12) (2014) 1361–1369 . [20] P. Dorjee , D. Amarasiriwardena , B. Xing , Antimony adsorption by zero-valent
iron nanoparticles (nZVI): ion chromatography–inductively coupled plasmamass spectrometry (IC–ICP-MS) study, Microchem. J. 116 (2014) 15–23 .
[21] T. Masciangioli , W.X. Zhang , Environmental technologies at the nanoscale, En-
viron. Sci. Technol 37 (5) (2003) 102A–108A . [22] M.R. Carter , Soil Sampling and Methods of Analysis, CRC Press LLC, Boca Raton,
FL, 2007 . [23] R. Chemlal , A. Tassist , M. Drouiche , H. Lounici , N. Drouiche , N. Mameri , Mi-
crobiological aspects study of bioremediation of diesel-contaminated soils bybiopile technique, Int. Biodeterior. Biodegradation 75 (2012) 201–206 .
[24] R. De la Torre-Sánchez , I. Baruch , J. Barrera-Cortés , Neural prediction of hydro-carbon degradation profiles developed in a biopile, Expert Syst. Appl 31 (2006)
383–389 . 25] M. Kriipsalu , M. Marques , D.R. Nammari , W. Hogland , Bio-treatment of oily
sludge: the contribution of amendment material to the content of target con-taminants, and the biodegradation dynamics, J. Hazard. Mater 148 (2007)
616–622 . 26] I. San Román , A. Galdames , M. Alonso , L. Bartolomé, J.L. Vilas , R.M. Alonso , Ef-
fect on coating on the environmental application of zerovalent iron nanoparti-
cles: the Lindane case, Sci. Total Environ 565 (2016) 795–803 . [27] OECD Guideline for Testing of Chemicals 207 , Earthworm, acute toxicity tests,
2007 . [28] OECD Guideline for Testing of Chemicals 208 , Terrestrial plants, growth test,
1984 . [29] M. Gil-Díaz , J. Alonso , E. Rodríguez-Valdés , P. Pinilla , M.C. Lobo , Reducing the
mobility of arsenic in brownfield soil using stabilised zero-valent iron nanopar-
ticles, J. Environ. Sci. Health A 49 (2014) 1361–1369 . [30] M. Gil-Díaz , A. Pérez-Sanz , M.A. Vicente , M.C. Lobo , Immobilisation of Pb and
Zn in soils using stabilised zero-valent iron nanoparticles: effects on soil prop-erties, Clean (Weinh) 42 (2014) 1776–1784 .
[31] M. Gil-Díaz , L.T. Ortiz , G. Costa , J. Alonso , M.L. Rodriguez-Membibre ,S. Sánchez-Fortún , et al. , Immobilization and leaching of Pb and Zn in an acidic
soil treated with zerovalent iron nanoparticles (nZVI): physicochemical and
toxicological analysis of leachates, Water Air Soil Pollut 225 (2014) 1–13 . [32] C. Fajardo , M. Gil-Díaz , G. Costa , J. Alonso , A.M. Guerrero , M. Nande , et al. ,
Residual impact of aged nZVI on heavy metal-polluted soils, Sci. Total Environ535 (2015) 79–84 .
[33] M.T. Gueye , E. Petrucci , L. Di Palma , Chemical reduction of hexavalentchromium (VI) in soil slurry by nano zero valent iron, Chem. Eng. Trans 43
(2015) 655–660 .
[34] USEPA (United States Environmental Protection Agency) , Polycyclic aromatichydrocarbons (PAHs) Technical report. Washington, DC, USA, 2008 .
[35] R. Kanaly , S. Harayama , Biodegradation of high-molecular-weight polycyclicaromatic hydrocarbons by bacteria, J. Bacteriol 182 (8) (20 0 0) 2059–2067 .
36] T. Sayara , M. Sarrà, A. Sánchez , Effects of compost stability and contaminantconcentration on the bioremediation of PAHs-contaminated soil through com-
posting, J. Hazard. Mater 179 (2010) 999–1006 .
[37] S.M. Bamforth , I. Singleton , Bioremediation of polycyclic aromatic hydrocar-bons: current knowledge and future directions, J. Chem. Technol. Biotechnol
80 (2005) 723–736 .
top related