disney dt1300c - m37281mah-066sp , m61206fp-61 , la78040a - tv sm
Post on 08-Sep-2015
236 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
13 COLOR TELEVISIONDT1300-C/DT1300-P/DT1300-A
SERVICE MANUAL
-
IMPORTANT SAFETY NOTICEProper service and repair is important to the safe, reliable operation of allFunai Equipment. The service procedures recommended by Funai and de-scribed in this service manual are effective methods of performing serviceoperations. Some of these service special tools should be used when andas recommended.It is important to note that this service manual contains various CAUTIONSand NOTICES which should be carefully read in order to minimize the risk ofpersonal injury to service personnel. The possibility exists that improperservice methods may damage the equipment. It also is important to under-stand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funaicould not possibly know, evaluate and advice the service trade of all con-ceivable ways in which service might be done or of the possible hazardousconsequences of each way. Consequently, Funai has not undertaken anysuch broad evaluation. Accordingly, a servicer who uses a service proce-dure or tool which is not recommended by Funai must first use all precau-tions thoroughly so that neither his safety nor the safe operation of theequipment will be jeopardized by the service method selected.
TABLE OF CONTENTSSpecifications ........................................................ 1-1Important Safety Precautions................................ 2-1Standard Notes for Servicing ................................ 3-1Disassembly Instructions ...................................... 4-1Electrical Adjustment Instructions ......................... 5-1Block Diagram....................................................... 6-1Schematic Diagram / CBAs and Test Points........ 7-1Schematic Diagram............................................... 7-3
CBA Views and Test Points................................. 7-11Wave Forms .......................................................... 8-1Wiring Diagram...................................................... 9-1IC Pin Function.................................................... 10-1Cabinet Exploded View ....................................... 11-1Packing Exploded View....................................... 11-3Mechanical Parts List .......................................... 12-1Electrical Parts List .............................................. 13-1
-
1-1 L6015SP
SPECIFICATIONS ANT. Input ------------------- 75ohm Unbal., F type
Reference Level------------20Vp-p (CRT Green Cathode)Test Input Signal -----------400Hz 30% modulation
All items are measured across 8 load at speaker output terminal.
Note:Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.
Description Condition Unit Nominal Limit1. Intermediate Freq. Picture
SoundMHzMHz
45.7541.25
-
-
2. Peak Picture Sens VHFCATVUHF
dBvdBvdBv
151515
303040
3. AFT Pull In Range(10mV input)
- MHz 2.0 0.7
Description Condition Unit Nominal Limit1. Deflection Freq. Horizontal
VerticalKHzHz
15.73460
-
-
2. Linearity HorizontalVertical
%%
-
-
1510
3. Over Scan - % 10 -4. High Voltage - KV 23 -
Description Condition Unit Nominal Limit1. Misconvergence Center
SideCorner
mmmmmm
-
-
-
0.31.21.5
2. Brightness APL 100% Ft-L 60 403. Color Temperature - K 9200K -4. Resolution Horizontal
VerticalLineLine
250300
-
-
Description Condition Unit Nominal Limit1. Audio Output Power 10% THD W 1 0.82. Audio Distortion (w/LPF) 500mW % 2 73. Audio Freq. Response -3dB Hz 100~11K -
-
2-1 L6115IMP
IMPORTANT SAFETY PRECAUTIONSPrior to shipment from the factory, our products are strictly inspected for recognized product safety and electricalcodes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equallyimportant to implement the following precautions when a set is being serviced.
Safety Precautions for TV Circuit 1. Before returning an instrument to the custom-
er, always make a safety check of the entire instru-ment, including, but not limited to, the followingitems:
a. Be sure that no built-in protective devices are de-fective and have been defeated during servicing.(1) Protective shields are provided on this chassisto protect both the technician and the customer.Correctly replace all missing protective shields, in-cluding any removed for servicing convenience.(2) When reinstalling the chassis and/or other as-sembly in the cabinet, be sure to put back in placeall protective devices, including but not limited to,nonmetallic control knobs, insulating fishpapers,adjustment and compartment covers/shields, andisolation resistor/capacitor networks. Do not oper-ate this instrument or permit it to be operatedwithout all protective devices correctly in-stalled and functioning. Servicers who defeatsafety features or fail to perform safety checksmay be liable for any resulting damage.
b. Be sure that there are no cabinet openings throughwhich an adult or child might be able to insert theirfingers and contact a hazardous voltage. Suchopenings include, but are not limited to, (1) spac-ing between the picture tube and the cabinetmask, (2) excessively wide cabinet ventilationslots, and (3) an improperly fitted and/or incorrectlysecured cabinet back cover.
c. Antenna Cold Check - With the instrument ACplug removed from any AC source, connect anelectrical jumper across the two AC plug prongs.Place the instrument AC switch in the on position.Connect one lead of an ohmmeter to the AC plugprongs tied together and touch the other ohmme-ter lead in turn to each tuner antenna input ex-posed terminal screw and, if applicable, to thecoaxial connector. If the measured resistance isless than 1.0 megohm or greater than 5.2 mego-hm, an abnormality exists that must be correctedbefore the instrument is returned to the customer.Repeat this test with the instrument AC switch inthe off position.
d. Leakage Current Hot Check - With the instru-ment completely reassembled, plug the AC linecord directly into a 120V AC outlet. (Do not use anisolation transformer during this test.) Use a leak-
age current tester or a metering system that com-plies with American National Standards Institute(ANSI) C101.1 Leakage Current for Appliancesand Underwriters Laboratories (UL) 1410, (50.7).With the instrument AC switch first in the on posi-tion and then in the off position, measure from aknown earth ground (metal water pipe, conduit,etc.) to all exposed metal parts of the instrument(antennas, handle brackets, metal cabinet, screwheads, metallic overlays, control shafts, etc.), es-pecially any exposed metal parts that offer an elec-trical return path to the chassis. Any currentmeasured must not exceed 0.5 milli-ampere. Re-verse the instrument power cord plug in the outletand repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITSSPECIFIED HEREIN INDICATE A POTENTIALSHOCK HAZARD THAT MUST BE ELIMINATEDBEFORE RETURNING THE INSTRUMENT TOTHE CUSTOMER OR BEFORE CONNECTINGTHE ANTENNA OR ACCESSORIES.
e. X-Radiation and High Voltage Limits - Becausethe picture tube is the primary potential source ofX-radiation in solid-state TV receivers, it is special-ly constructed to prohibit X-radiation emissions.For continued X-radiation protection, the replace-ment picture tube must be the same type as theoriginal. Also, because the picture tube shieldsand mounting hardware perform an X-radiationprotection function, they must be correctly in place.High voltage must be measured each time servic-
_
DEVICELEAKAGECURRENT
TESTER
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
+
READING SHOULDNOT BE ABOVE 0.5 mA
EARTHGROUND
BEINGTESTED
-
2-2 L6115IMP
ing is performed that involves B+, horizontal de-flection or high voltage. Correct operation of the X-radiation protection circuits also must be recon-firmed each time they are serviced. (X-radiationprotection circuits also may be called "horizontaldisable" or "hold down.") Read and apply the highvoltage limits and, if the chassis is so equipped,the X-radiation protection circuit specifications giv-en on instrument labels and in the Product Safety& X-Radiation Warning note on the service datachassis schematic. High voltage is maintainedwithin specified limits by close tolerance safety-re-lated components/adjustments in the high-voltagecircuit. If high voltage exceeds specified limits,check each component specified on the chassisschematic and take corrective action.
2. Read and comply with all caution and safety-relat-ed notes on or inside the receiver cabinet, on thereceiver chassis, or on the picture tube.
3. Design Alteration Warning - Do not alter or addto the mechanical or electrical design of this TV re-ceiver. Design alterations and additions, including,but not limited to circuit modifications and the ad-dition of items such as auxiliary audio and/or videooutput connections, might alter the safety charac-teristics of this receiver and create a hazard to theuser. Any design alterations or additions will voidthe manufacturer's warranty and may make you,the servicer, responsible for personal injury orproperty damage resulting therefrom.
4. Picture Tube Implosion Protection Warning -The picture tube in this receiver employs integralimplosion protection. For continued implosion pro-tection, replace the picture tube only with one ofthe same type number. Do not remove, install, orotherwise handle the picture tube in any mannerwithout first putting on shatterproof gogglesequipped with side shields. People not soequipped must be kept safely away while picturetubes are handled. Keep the picture tube awayfrom your body. Do not handle the picture tube byits neck. Some "in-line" picture tubes are equippedwith a permanently attached deflection yoke; be-cause of potential hazard, do not try to removesuch "permanently attached" yokes from the pic-ture tube.
5. Hot Chassis Warning - a. Some TV receiver chassis are electrically connect-
ed directly to one conductor of the AC power cordand maybe safety-serviced without an isolationtransformer only if the AC power plug is insertedso that the chassis is connected to the ground sideof the AC power source. To confirm that the ACpower plug is inserted correctly, with an AC volt-meter, measure between the chassis and a known
earth ground. If a voltage reading in excess of 1.0Vis obtained, remove and reinsert the AC powerplug in the opposite polarity and again measurethe voltage potential between the chassis and aknown earth ground.
b. Some TV receiver chassis normally have 85VAC(RMS) between chassis and earth ground re-gardless of the AC plug polarity. This chassis canbe safety-serviced only with an isolation transform-er inserted in the power line between the receiverand the AC power source, for both personnel andtest equipment protection.
c. Some TV receiver chassis have a secondaryground system in addition to the main chassisground. This secondary ground system is not iso-lated from the AC power line. The two ground sys-tems are electrically separated by insulationmaterial that must not be defeated or altered.
6. Observe original lead dress. Take extra care to as-sure correct lead dress in the following areas:a.near sharp edges,b. near thermally hot parts-besure that leads and components do not touch ther-mally hot parts,c. the AC supply,d. high voltage,and,e. antenna wiring. Always inspect in all areasfor pinched, out of place, or frayed wiring. CheckAC power cord for damage.
7. Components, parts, and/or wiring that appear tohave overheated or are otherwise damagedshould be replaced with components, parts, or wir-ing that meet original specifications. Additionally,determine the cause of overheating and/or dam-age and, if necessary, take corrective action to re-move any potential safety hazard.
8. Product Safety Notice - Some electrical and me-chanical parts have special safety-related charac-teristics which are often not evident from visualinspection, nor can the protection they give neces-sarily be obtained by replacing them with compo-nents rated for higher voltage, wattage, etc.. Partsthat have special safety characteristics are identi-fied by a ( # ) on schematics and in parts lists. Useof a substitute replacement that does not have thesame safety characteristics as the recommendedreplacement part might create shock, fire, and/orother hazards. The product's safety is under re-view continuously and new instructions are issuedwhenever appropriate. Prior to shipment from thefactory, our products are strictly inspected to con-firm they comply with the recognized product safe-ty and electrical codes of the countries in whichthey are to be sold. However, in order to maintainsuch compliance, it is equally important to imple-ment the following precautions when a set is beingserviced.
-
2-3 L6115IMP
Precautions during Servicing A. Parts identified by the ( # ) symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assembliesare specified for conformance with regulations ap-plying to spurious radiation. These must also bereplaced only with specified replacements.Examples: RF converters, RF cables, noise block-ing capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous
live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends ofwires securely about the terminals before solder-ing.
F. Observe that the wires do not contact heat produc-ing parts (heatsinks, oxide metal film resistors, fus-ible resistors, etc.)
G. Check that replaced wires do not contact sharpedged or pointed parts.
H. When a power cord has been replaced, check that5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder drop-
lets, etc.) do not remain inside the set. K. Crimp type wire connector
The power transformer uses crimp type connec-tors which connect the power cord and the primaryside of the transformer. When replacing the trans-former, follow these steps carefully and preciselyto prevent shock hazards.Replacement procedure
1) Remove the old connector by cutting the wires ata point close to the connector.Important: Do not re-use a connector (discard it).
2) Strip about 15 mm of the insulation from the endsof the wires. If the wires are stranded, twist thestrands to avoid frayed conductors.
3) Align the lengths of the wires to be connected. In-sert the wires fully into the connector.
4) Use the crimping tool to crimp the metal sleeve atthe center position. Be sure to crimp fully to thecomplete closure of the tool.
L. When connecting or disconnecting the internalconnectors, first, disconnect the AC plug from theAC supply outlet.
-
2-4 L6115IMP
Safety Check after ServicingExamine the area surrounding the repaired locationfor damage or deterioration. Observe that screws,parts and wires have been returned to original posi-tions. Afterwards, perform the following tests and con-firm the specified values in order to verify compliancewith safety standards.
1. Clearance DistanceWhen replacing primary circuit components, confirmspecified clearance distance (d) and (d') between sol-dered terminals, and between terminals and surround-ing metallic parts. (See Fig. 1)
Table 1 : Ratings for selected area
Note: This table is unofficial and for reference only.Be sure to confirm the precise values.
2. Leakage Current TestConfirm the specified (or lower) leakage current be-tween B (earth ground, power cord plug prongs) andexternally exposed accessible parts (RF terminals,antenna terminals, video and audio input and outputterminals, microphone jacks, earphone jacks, etc.) islower than or equal to the specified value in the tablebelow.
Measuring Method : (Power ON)Insert load Z between B (earth ground, power cordplug prongs) and exposed accessible parts. Use anAC voltmeter to measure across both terminals ofload Z. See Fig. 2 and following table.
Table 2 : Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d) (d')110 to 130 V USA or CANADA
3.2 mm (0.126 inches)
Chassis or Secondary Conductor
dd'
Primary Circuit Terminals
Fig. 1
AC Voltmeter(High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
1.5k0.15F
Fig. 2
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V USA0.15F CAP. & 1.5k
RES. connected in parallel
i0.5mA rms Exposed accessible parts
-
3-1 L6115STA
STANDARD NOTES FOR SERVICINGCircuit Board Indications a. The output pin of the 3 pin Regulator ICs is indicat-
ed as shown.
b. For other ICs, pin 1 and every fifth pin are indicat-ed as shown.
c. The 1st pin of every male connector is indicated asshown.
How to Remove / Install Flat Pack-IC1. RemovalWith Hot-Air Flat Pack-IC Desoldering Machine:(1) Prepare the hot-air flat pack-IC desoldering ma-
chine, then apply hot air to the Flat Pack-IC (about5 to 6 seconds). (Fig. S-1-1)
(2) Remove the flat pack-IC with tweezers while ap-plying the hot air.
(3) Bottom of the flat pack-IC is fixed with glue to theCBA; when removing entire flat pack-IC, first applysoldering iron to center of the flat pack-IC and heatup. Then remove (glue will be melted). (Fig. S-1-6)
(4) Release the flat pack-IC from the CBA using twee-zers. (Fig. S-1-6)
Caution: 1. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damageto the chip parts may occur. Put masking tapearound the flat pack-IC to protect other parts fromdamage. (Fig. S-1-2)
2. The flat pack-IC on the CBA is affixed with glue, sobe careful not to break or damage the foil of eachpin or the solder lands under the IC when remov-ing it.
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
Fig. S-1-1
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
-
3-2 L6115STA
With Soldering Iron:(1) Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solderflux which is applied to all pins of the flat pack-IC,you can remove it easily. (Fig. S-1-3)
(2) Lift each lead of the flat pack-IC upward one byone, using a sharp pin or wire to which solder willnot adhere (iron wire). When heating the pins, usea fine tip soldering iron or a hot air desoldering ma-chine.(Fig. S-1-4)
(3) Bottom of the flat pack-IC is fixed with glue to theCBA; when removing entire flat pack-IC, first applysoldering iron to center of the flat pack-IC and heatup. Then remove (glue will be melted). (Fig. S-1-6)
(4) Release the flat pack-IC from the CBA using twee-zers. (Fig. S-1-6)
With Iron Wire:(1) Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solderflux which is applied to all pins of the flat pack-IC,you can remove it easily. (Fig. S-1-3)
(2) Affix the wire to a workbench or solid mountingpoint, as shown in Fig. S-1-5.
(3) While heating the pins using a fine tip solderingiron or hot air blower, pull up the wire as the soldermelts so as to lift the IC leads from the CBA con-tact pads as shown in Fig. S-1-5.
(4) Bottom of the flat pack-IC is fixed with glue to theCBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heatup. Then remove (glue will be melted). (Fig. S-1-6)
(5) Release the flat pack-IC from the CBA using twee-zers. (Fig. S-1-6)
Note:When using a soldering iron, care must be taken toensure that the flat pack-IC is not being held byglue. When the flat pack-IC is removed from theCBA, handle it gently because it may be damagedif force is applied.
Flat Pack-IC Desoldering Braid
Soldering IronFig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
-
3-3 L6115STA
2. Installation(1) Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBAso you can install a replacement flat pack-IC moreeasily.
(2) The "I" mark on the flat pack-IC indicates pin 1.(See Fig. S-1-7.) Be sure this mark matches the 1on the PCB when positioning for installation. Thenpre- solder the four corners of the flat pack-IC.(See Fig. S-1-8.)
(3) Solder all pins of the flat pack-IC. Be sure thatnone of the pins have solder bridges.
Instructions for Handling SemiconductorsElectrostatic breakdown of the semiconductors mayoccur due to a potential difference caused by electro-static charge during unpacking or repair work.
1. Ground for Human BodyBe sure to wear a grounding band (1M) that is prop-erly grounded to remove any static electricity that maybe charged on the body.
2. Ground for WorkbenchBe sure to place a conductive sheet or copper platewith proper grounding (1M) on the workbench orother surface, where the semiconductors are to beplaced. Because the static electricity charge on cloth-ing will not escape through the body grounding band,be careful to avoid contacting semiconductors withyour clothing.
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
CBA
CBA
Grounding Band
Conductive Sheet orCopper Plate
1M
1M
-
4-1 L6310DC
CABINET DISASSEMBLY INSTRUCTIONS1. Disassembly FlowchartThis flowchart indicates the disassembly steps for thecabinet parts, and the CBA in order to gain access toitem(s) to be serviced. When reassembling, follow thesteps in reverse order. Bend, route and dress thecables as they were.Caution !When removing the CRT, be sure to discharge theAnode Lead of the CRT with the CRT Ground Wirebefore removing the Anode Cap.
2. Disassembly Method
(1) (2) (3) (4) (5)
Note :(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbersare also used as the Identification (location) No. ofparts in figures.
(2) Parts to be removed or installed.(3) Fig. No. showing procedure of part location(4) Identification of part to be removed, unhooked, un-
locked, released, unplugged, unclamped, ordesoldered.S=Screw, P=Spring, L=Locking Tab, CN=Con-nector, *=Unhook, Unlock, Release, Unplug, orDesolder2(S-2) = two Screws (S-2)
(5) Refer to the following "Reference Notes in the Table.
Reference Notes in the Table 1. Removal of the Rear Cabinet. Remove screws
4(S-1), (S-2), (S-3), then slide the Rear Cabinetbackward.
2. Removal of the CRT CBA. Disconnect CN501 thenpull the CRT CBA backward.
Caution !Discharge the Anode Lead of the CRT with the CRTGround Wire before removing the Anode Cap. 3. Removal of the Main CBA. First, disconnect
CN801A, CN802A, CN691, and CN571 on theMain CBA. Second, remove Anode Cap then slidethe Main CBA backward.
4. Removal of the CRT. Remove screws 4(S-7) andAnode Cap then slide the CRT backward.
Step/Loc. No.
Part
Removal
Fig. No
Remove/*unlock/release/unplug/unclamp/desolder
Note
[1] Rear Cabinet 1,2 4(S-1), (S-2), (S-3) 1
[2] Jack A CBA 2 2(S-4), CN811B -[3] Jack B CBA 2 2(S-5), CN812B -
[4] Function CBA 2 5(S-6), CN101B -
[5] CRT CBA 4,5 CN501 2
[6] Main CBA 3,5CN801A, CN802A, CN691, CN301A, CN571, Anode Cap
3
[7] CRT 4 4(S-7) 4
[1] Rear Cabinet
[2] Jack A CBA [3] Jack B CBA
[4] Function CBA
[5] CRT CBA
[6] Main CBA
[7] CRT
-
4-2 L6310DC
Fig. 1
S-1
S-1
[1] REAR CABINET
S-3S-2
Fig. 2
[1] REAR CABINET
S-2
S-3
S-1
S-1
S-1
S-4
S-5 S-6S-6
[2] JACK A CBA
[3] JACK B CBA
[4] FUNCTION CBA
-
4-3 L6310DC
Fig. 3
[3] MAIN CBAFront Cabinet
Fig. 4
Front Cabinet
[4] CRTS-2
S-2
S-2
S-2[2] CRT CBAAnode Cap
Degaussing Coil
-
4-4 L6310DC
TV Cable Wiring Diagram
Fig. 5
SP802 SP801
DG691 DEGAUSSING COIL
MAIN CBA
FUNCTION CBA
CRT CBA
JACK A CBA
JACK B CBA
FLYBACK TRANSFORMER
TO CRT GROUND
CN501
CN301B
SCREEN
FOCUS
CN101B
CN811B
CN812B
CN101ACN801A
CN811A
CN802A
CN812A
CN691
CN571
CN581A
CN301A
TU1TUNER
WH581B
AC601AC CORD
ANODE
-
5-1 L6310EA
ELECTRICAL ADJUSTMENT INSTRUCTIONSGeneral Note:"CBA" is abbreviation for "Circuit Board Assem-bly".NOTE:
Electrical adjustments are required after replacingcircuit components and certain mechanical parts.It is important to perform these adjustments onlyafter all repairs and replacements have been com-pleted. Also, do not attempt these adjustments unless theproper equipment is available.
Test Equipment Required 1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
2. DC Voltmeter 3. Oscilloscope: Dual-trace with 10:1 probe,
V-Range: 0.001~50V/Div, F-Range: DC~AC-60MHz
4. Plastic Tip Driver 5. Remote control unit:Part No. N0121UD or N0134UD 6. DC power supply 13.2V/5A
How to make Service remote control unit: 1. Prepare normal remote control unit. (Part No.
N0121UD or N0134UD) Remove 3 Screws fromthe back lid. (Fig. 1-1)
2. Add J1 (Jumper Wire) to the remote control CBA.(Fig. 1-2)
How to set up the service mode:Service mode: 1. Use the service remote control unit. 2. Turn the power on. (Use main power on the TV unit.) 3. Press "SLEEP" button on the service remote con-
trol unit. Version of micro computer will display onthe CRT. (Ex: 200-0.07 or 054-0.13)
4. When CPU version is 054-0.13: Check the displayon the lower left is "00" and if it is not "00", set it at"00" according to "3-1 FRENCH, ACCESS CODE,VIDEO TONE".When CPU version is 200-0.07: Confirm that thecharacter of U ( U.S.A. model ) is indicated on thebottom left of the CRT. If the character of C ( CAN-ADA model ) is indicated, perform "3-1 Setting forFRENCH data Values".
1. DC 105V AdjustmentPurpose: To obtain correct operation.Symptom of Misadjustment: The picture is dark andthe unit does not operate correctly.
Note: TP601, TP300(GND), VR661 --- Main CBA 1. Connect DC Volt Meter to TP601 and TP300(GND). 2. Adjust VR661 so that the voltage of TP601 becomes
+1050.5V DC.
2. Black Stretch Control AdjustmentPurpose: To show the fine black color.Symptom of Misadjustment: Black color will notappear correctly.Note: Use Service remote control unit. 1. Enter the Service mode. (See page 5-1) 2. Press "6" button on the Service remote control
unit. "B-S" is indicated. 3. Press "CHo / p" buttons on the Service remote con-
trol unit so that display will change " OFF ", "0", " 1 "," 2 " and " 3 ". Then choose " B-S OFF ".
4. Press "6" button on the Service remote controlunit. " B-S*2 " is indicated.
5. Press "CHo / p" buttons on the Service remotecontrol unit so that display will change "0", " 1 ". " 2" and " 3 ". Then choose " B-S*2 0 ".
6. Turn the power off and on again. (Main power but-ton on the TV unit.)
SCREW
REMOTE CONTROL UNIT Fig. 1-1
J 1
Fig. 1-2REMOTE CONTROL CBA
Test Point Adj. Point Mode InputTP601 TP300 (GND)
VR661 --- ---
Tape M. EQ. Spec.--- DC Voltmeter +1050.5V DC.
-
5-2 L6310EA
3-1. Setting for 7F and FRENCH data Values
General 1. Enter the Service mode. (See page 5-1) 2. Press "VOL p" button on the Service remote con-
trol unit. Display changes " C/D ", " VCO ", " 7F "," FRENCH ", " ACCESS CODE ", " STEREO "," VIDEO TONE ", " FM-MODE " and " AV-OUT " cy-clically when "VOL p" button is pressed.
7F 1. Press " VOL p " button on the Service remote
control unit. Then select 7F display. 2. Press "CH o / p" buttons on the Service remote
control unit. Then choose 7F=FF.FRENCH 1. Press "VOL p" button on the Service remote con-
trol unit. Then select FRENCH display. 2. Press "CH o / p" buttons on the Service remote
control unit. Then choose FRENCH=OFF.
When CPU version is 053-0.11, perform the follow-ing settings:ACCESS CODE ---- set to OFF VIDEO TONE ---- set to OFF FM-MODE ---- set to ONAV-OUT ---- set to OFF STEREO ---- set to OFF
Note: C/D and VCO data values do not need to beadjusted at this moment.
3-2. Setting for CONTRAST, COLOR, TINT, V-TINT and SHARP data Values
General 1. Enter the Service mode. (See page 5-1) 2. Press " MENU " button on the Service remote control
unit. Display changes " BRIGHT ", " CONTRAST ", "COLOR ", " TINT ", " V-TINT " and " SHARP " cyclical-ly when " MENU " button is pressed.
CONTRAST (CNT) 1. Press " MENU " button on the Service remote con-
trol unit. Then select " CONTRAST " (CNT) display. 2. Press "CH o / p" buttons on the Service remote
control unit so that the value of " CONTRAST "(CNT) becomes 78.
COLOR (CLR) 1. Press " MENU " button on the Service remote con-
trol unit. Then select " COLOR " (CLR) display. 2. Press "CH o / p" buttons on the Service remote
control unit so that the value of " COLOR " (CLR)becomes 58.
TINT (TNT) 1. Press " MENU " button on the Service remote con-
trol unit. Then select " TINT " (TNT) display. 2. Press "CH o / p" buttons on the Service remote
control unit so that the value of " TINT " (TNT) be-comes 60.
V-TINT (V-TNT) 1. Press " MENU " button on the Service remote con-
trol unit. Then select " V-TINT " (V-TNT) display. 2. Press "CH o / p" buttons on the Service remote
control unit so that the value of " V-TINT " (V-TNT)becomes 62.
SHARP (SHARP) 1. Press " MENU " button on the Service remote con-
trol unit. Then select " SHARP " (SHARP) display. 2. Press "CH o / p" buttons on the Service remote
control unit and select " SHARP OFF ".Note: BRIGHT data value does not need to be adjust-
ed at this moment.
-
5-3 L6310EA
4. H fo AdjustmentPurpose: To get correct horizontal frequency.Symptom of Misadjustment: . If H f0 adjustment is incorrect, skew distortion will appear on the screen.
Note: R583 --- Main CBAUse Service remote control unit.
1. Connect Frequency Counter to R583 and ground. 2. Set the unit to the VIDEO mode which is located
before CH2 and no input is necessary. Enter theService mode. (See Page 5-1)
3. Operate the unit for at least 20 minutes. 4. Press " 2 " button on the Service remote control
unit and select H-ADJ Mode. (By pressing " 2 " but-ton the display will change from TV AGC to H-ADJ)
5. Press "CH o / p" button on the Service remote control unit so that the display will change "0" ~ " 7 ".At this moment, Choose display one of them from "0" ~ " 7 " when the Frequency Counter shows15.734 kHz300Hz or closer.
6. Turn the power off and on again. (Main Power but-ton on the TV unit.)
5. VCO AdjustmentPurpose: To operate VCO correctly.Symptom of Misadjustment: VCO does not workcorrectly and/or synchronization is faulty.
Note: Use service remote control unit. 1. Disconnect the RF input and set the unit to Channel 4. 2. Enter the Service mode. (See Page 5-1) 3. Press " 3 " button on the Service remote control
unit. The Auto VCO adjustment is started. 4. If the display color is changed from red to green,
This adjustment is done. 5. Turn the Power off and on again. (Main power but-
ton on the TV unit.)
6-1. AGC AdjustmentPurpose: Set AGC (Auto Gain Control) Level.Symptom of Misadjustment: AGC does not syn-chronize correctly when RF input level is too weak andpicture distortion may occur if it is too strong.
Notes: TP301 --- Main CBAUse Service remote control unit.
1. Enter the Service mode. (See Page 5-1) Thenpress number " 2 " button on the Service remotecontrol unit.
2. Receive the Color Bar signal for channel 4(67.25MHz). (RF Input Level: 60dBV)
3. Press "CH o / p" buttons so that the voltage ofTP301 becomes +2.70.1V DC.
4. Turn the Power off and on again. (Main power but-ton on the TV unit.)
6-2. FM AGC Adjustment1. Enter the Service mode. (See page 5-1.) Then
press number "2" button twice on the remote con-trol unit.
2. Press CH.o / p buttons so that the FM AGC(MAX) level is 127.
7. Black Level AdjustmentPurpose: Set Sub-bright LevelSymptom of Misadjustment: If Sub-brightness isincorrect, Proper brightness can not be obtained byadjusting the Brightness Control.Note: TP300 (GND), D316 (Cathode) --- MAIN CBA 1. Enter the Service mode. (See page 5-1). 2. Press " MENU " button on the Service remote con-
trol unit and select " BRT " mode. (Display chang-es " BRT ", " CNT ", " CLR " and " TNT " cyclicallywhen MENU button is pressed).
3. Press "CH o / p" buttons on the Service remotecontrol unit so that the value of " BRT " becomes128.
4. Turn the power off and on again. (Main power but-ton on the TV unit.)
Test Point Adj. Point Mode Input
R583CHo / p button
["H-ADJ"] MODE
---
Tape M. EQ. Spec.
---
Frequency Counter 15.734kHz300Hz
Test Point Adj. Point Mode Input--- ---
No signal
Tape M. EQ. Spec.--- --- ---
Test Point Adj. Point Mode Input
TP301 CHo / p buttons RFColor Bar 67.25MHz 60dBV
Tape M. EQ. Spec.
---
Pattern Generator DC
Volt Meter+2.70.1VDC
-
5-4 L6310EA
8. C-Trap AdjustmentPurpose: To get minimum leakage of the color signal carrier.Symptom of Misadjustment: If C-Trap Adjustment isincorrect, stripes will appears on the screen.
Note: TP300 (GND), D316 (Cathode) --- MAIN CBAUse Service remote control unit.
1. Connect Oscilloscope to D316 (Cathode) andTP300 (GND).
2. Enter the Service mode. (See Page 5-1) Receivecolor bar signal from RF Input.
3. Press "0" button on the Service remote control unitand select C-TRP Mode.
4. Press "CH o / p" buttons on the Service remote con-trol unit so that the display will change "0", " 1 ", " 2 "and " 3 ". Choose display "0", " 1 ", " 2 " or " 3 " whenB-Out (3.58MHz) value becomes minimum on the os-cilloscope reading.
5. Turn the power off and on again. (Main power but-ton on the TV unit.)
9. V. Size AdjustmentPurpose: To obtain correct vertical width of screen image.Symptom of Misadjustment: If V.Size is incorrect, verticalsize of image on the screen may not be properly displayed.
Note: Use service remote control unit. 1. Operate the unit for at least 20 minutes. 2. Enter the Service mode. (See page 5-1) 3. Receive the Monoscope Pattern. 4. Press " 9 " button on the Service remote control unit
and select " V-S " mode. (Display changes " V-S "and " V-P " cyclically when " 9 " button is pressed).
5. Press "CH o / p" buttons on the Service remotecontrol unit so that the monoscope pattern will be905% of display size and the circle is round.
6. Turn the power off and on again. (Main power but-ton on the TV unit.)
10. V. Position AdjustmentPurpose: To obtain correct vertical width of screenimage.Symptom of misadjustment: If V. Position is incor-rect, vertical height of image on the screen may not beproperly displayed.
Note: Use Service remote control unit 1. Operate the unit for at least 20 minutes. 2. Enter the Service Mode. (See page 5-1) 3. Receive the Monoscope Pattern. 4. Press " 9 " button on the Service remote control unit
and select " V-P " mode. (Display change " V-S " and" V-P " cyclically when " 9 " button is pressed).
5. Press "CH o / p" buttons on the Service remotecontrol unit so that the top and bottom of the mono-scope pattern will be equal of each other.
6. Turn the Power off and on again. (Main power but-ton on the TV unit.)
Test Point Adj. Point Mode InputD316 (Cathode)
(Blue)TP300(GND)
CHo / p buttons RF
Color Bar
Tape M. EQ. Spec.--- Oscilloscope ---
Test Point Adj. Point Mode Input
---
Screen Control CHo / p
buttons [ V-S ] Mode
RF Mono-scope
Tape M. EQ. Spec.--- Monoscope 905%
Test Point Adj. Point Mode Input--- Screen Control
CHo / p buttons [ V-P ]
Mode
RF Mono-scope
Tape M. EQ. Spec.--- Monoscope 905%
-
5-5 L6310EA
11. H. Position AdjustmentPurpose: To obtain correct horizontal position ofscreen image.Symptom of Misadjustment: If H. Position is incor-rect, horizontal position of image on the screen maynot be properly displayed.
Note: Use Service remote control unit 1. Operate the unit for at least 20 minutes. 2. Enter the Service mode. (See page 5-1) 3. Receive the Monoscope Pattern. 4. Press " 8 " button on the remote control unit and
select " H-P " mode. 5. Press "CH o / p" buttons on the Service remote
control unit so that the monoscope pattern will be905% of display size and the circle is round.
6. Turn the Power off and on again. (Main power but-ton on the TV unit.)
12. Cut-off AdjustmentPurpose: To adjust the beam current of R, G, B, andscreen voltage.Symptom of Misadjustment: White color may bereddish, greenish or bluish.
Note: Screen Control FBT --- Main CBAF.B.T= Fly Back TransformerUse Service remote control unit
1. Degauss the CRT and allow CRT to operate for 20minutes before starting the alignment.
2. Input the Black Raster Signal from RF Input. 3. Enter the Service mode. (See page 5-1) 4. Press "VOL p" button on the Service remote con-
trol unit and select " C/D " mode. (Display changes" C/D ", " VCO ", " 7F " and " FRENCH " cyclicallywhen "VOL p" button is pressed.) then press " 1 ".The display will momentarily show " CUT OFF R "(R= Red). Now there should be a horizontal lineacross the center of the picture tube. If neededgradually turn the screen control on the flyback,clockwise until the horizontal line appears. Adjustthe Red Cut off by pressing the "CH o / p" buttons.Proceed to Step 5 when the Red Cut off adjustmentis done.
5. Press the " 2 " button. The display will momentarilyshow " CUT OFF G " (G=Green). Adjust the GreenCut off by pressing the "CH o / p" buttons. Proceedto step 6 when the Green Cut off adjustment is done.
6. Press the " 3 " button. The display will momentarilyshow " CUT OFF B " (B=Blue). Adjust the Blue cutoff by pressing the "CH o / p" buttons. When donewith steps 4, 5 and 6 the horizontal line should bepure white if not, then attempt the Cut off adjust-ment again.
Test Point Adj. Point Mode Input
---
Screen Control CHo / p
buttons [ H-P ] Mode
RF Mono-scope
Tape M. EQ. Spec.--- Monoscope 905%
Test Point Adj. Point Mode Input
---
Screen-Control CHo / p buttons
RF Black Raster
Tape M. EQ. Spec.
---
Pattern Generator
See Reference Notes below.
Figure
PATTERN GENERATOR
Fig 2EXT. INPUT
-
5-6 L6310EA
13. White Balance AdjustmentPurpose: To mix red, green and blue beams correctlyfor pure white. Symptom of Misadjustment: White becomes bluishor reddish.
Note: Use Service remote control unit 1. Operate the unit more than 20 minutes. 2. Face the unit to east. Degauss the CRT using De-
gaussing Coil. 3. Input the White Raster (APL 100%). 4. Set the color analyzer to the CHROMA mode and
after zero point calibration, bring the optical recep-tor to the center on the tube surface (CRT).
5. Enter the Service mode. Press "VOL p" button onthe Service remote control unit and select " C/D "mode. (Display changes " C/D ", "VCO ", " 7F " and" FRENCH " cyclically when "VOL p" button ispressed.) then Press No. 8 button on the Serviceremote control Unit.
6. Press No. 4 button on the service remote controlunit for Red adjustment. Press N0. 5 button on theService remote control unit for Blue adjustment.
7. In each color mode, Press "CH o / p" button to ad-just the values of color.
8. Adjusting Red and Blue color so that the tempera-ture becomes 9200K (x : 286 / y : 294) 3%.
9. At this time, Re-check that Horizontal line is white.If not, Re-adjust Cut-off Adjustment until the Hori-zontal Line becomes pure white.
10. Turn off and on again to return to normal mode. Re-ceive APL 100% white signal and Check Chromatemperatures become 9200K (x : 286 / y : 294) 3%.
Note: Confirm that Cut Off Adj. is correct after thisadjustment, and attempt Cut Off Adj. if needed.
14. Sub-Brightness AdjustmentPurpose: To get proper brightness.Symptom of Misadjustment: If Sub-Brightness isincorrect, proper brightness cannot be obtained byadjusting the Brightness Control.
Note: IQW Setup level --- 7.5 IREUse Service remote control unit
1. Enter the Service mode. (See page 5-1)Then input IQW signal from RF Input.
2. Press " MENU " button on the Service remote con-trol unit and Select " BRT " mode. (Display changes" BRT ", " CNT ", " CLR ", and " TNT " cyclically whenMENU button is pressed). Press "CH o / p" buttonsso that the bar is just visible (See above figure).
3. Turn the power off and on again. (Main power but-ton on the TV unit.)
15. Focus AdjustmentPurpose: Set the optimum Focus.Symptom of Misadjustment: If Focus Adjustment isincorrect, blurred images are shown on the display.
Note: Focus VR (FBT) --- Main CBA FBT= Fly Back Transformer1. Operate the unit more than 30 minutes2. Face the unit to the East and Degauss the CRT us-
ing Degaussing Coil.3. Input the Monoscope Pattern.4. Adjust the Focus Control on the FBT to obtain
clear picture.
Test Point Adj. Point Mode Input
ScreenScreen-Control
CHo / p buttons
RF
White Raster (APL
100%)Tape M. EQ. Spec.
Pattern Generator,
Color analyzerSee below
Figure
Color Analyzer Fig. 3
Test Point Adj. Point Mode Input---
CHo / p buttons RF IQW
Tape M. EQ. Spec.
---
Pattern Generator See below
Figure
Test Point Adj. Point Mode Input--- Focus Control RF Mono-
scopeTape M. EQ. Spec.
---
Pattern Generator See below
White Black
Fig. 4
This bar just visible
-
5-7 L6310EA
The following 2 adjustments normally are notattempted in the field. Only when replacing theCRT then adjust as a preparation.16. Purity AdjustmentPurpose: To obtain pure color.Symptom of Misadjustment: If Color Purity Adjust-ment is incorrect, large areas of color may not beproperly displayed.
1. Set the unit facing east. 2. Operate the unit for over 30 minutes before adjust-
ing. 3. Fully degauss the unit using an external degauss-
ing coil. 4. Loosen the screw on the Deflection Yoke Clamper
and pull the Deflection Yoke back away from thescreen. (See Fig. 6)
5. Loosen the Ring Lock and adjust the Purity Mag-nets so that a red field is obtained at the center ofthe screen. Tighten Ring Lock. (See Fig. 5,6)
6. Slowly push the Deflection Yoke toward bell ofCRT and set it where a uniform red field is ob-tained.
7. Tighten the clamp screw on the Deflection Yoke.
17. Convergence AdjustmentPurpose: To obtain proper convergence of red, greenand blue beams.Symptom of Misadjustment: If Convergence Adjust-ment is incorrect, the edge of white letters may havecolor edges.
1. Loosen the Ring Lock and align red with blue dotsor Crosshatch at the center of the screen by rotating(RB) C.P. Magnets. (See Fig. 7)
2. Align red / blue with green dots at the center of thescreen by rotating (RB-G) C.P. Magnet. (See Fig. 8)
3. Fix the C.P. Magnets by tightening the Ring Lock.4. Remove the DY Wedges and slightly tilt the De-
flection Yoke horizontally and vertically to obtainthe best overall convergence.
5. Fix the Deflection Yoke by carefully inserting theDY Wedges between CRT and Deflection Yoke.
Test Point Adj. Point Mode Input
---
Deflection Yoke Purity
Magnet---
Red Color
Tape M. EQ. Spec.
---
Pattern Generator See below.
Figure
GREEN RED BLUE
Fig. 5
Test Point Adj. Point Mode Input
---
C.P. Magnet (RB), C.P. Magnet (RB-G),
Deflection Yoke---
Dot Pattern or
CrosshatchTape M. EQ. Spec.
---
Pattern Generator See below.
Figure
DY WEDGE
DEFLECTION YOKE
C.P. MAGNET
RING LOCK
SCREW
SCREW RB-GRBPURITYCRT
COIL
COIL CLAMPER
C.P. MAGNET CLAMPER
Fig. 6
G G
G
R R
BFig. 7
C.P. MAGNET (RB)
G GRB
RB
Fig. 8
C.B. MAGNET (RB-G)
-
L6310BLIF
BLOCK DIAGRAMS
6-1 6-2
32
2117
122925
27202830
5
1
64
62
10
VCXO
INV
V.RAMP
REFFILTER
VERTICALCOUNTDOWN
RGBEXT.INPUT
X3443.58MHz
HORIZONTALCOUNTDOWN
ADJDET
VCCADJ
RGB MATRIXCONTRAST BRIGHT CLAMP
CLAMP
DELAY
HVBLK
CN301A TO CN301B
DRIVEAMP
VIDEOMUTE
VIDEOTONE
BLACKSTRETCHGAMMAH
VCO
BGPGENE.
KILLERDET
CHROMABPF
V-SYNCTRIG.
SYNCSEPA
CHROMATRAP
VCOADJ
4.5MHzTRAP
FBPH-DRIVEACL/ABL
CF301
4.5MHzBPF
CF302
VIDEODET
VIFAMPSAWFILTER
KEYSWITCH
SF1
APCDET
INTELLIGENTMONITORING
ACCDET
ACCHPF
LPFAFT
IF AGCRF AGC
IC301 (VIDEO/AUDIO/CHROMA/DEFLECTION)
VCOLOCK DET
CHROMAAPC DET
1431
1516
67
40
43
36
57
DEMODULATOR
AFC-2
AFC-1
H.COINCIDENCE
EQELIMINATE
BUSI/F
BUSCONTROL
X2
TU1
IFAGC
TP301AGC
SDASCL
EXT.CLK
111
548
TP300GND
IC101 (TV MICON)
IC151(MEMORY)
SW101-SW106
V-SYNCH-SYNC
OSD-ROSD-GOSD-B
CVIN
SD
KEY-IN
SDASCL
SDASCL
I2C-OPEN
V-DRIVEV-RAMP-F/B
3738
5
39
22
9
21
49505152
SDA 4I2C-OPEN 2SD 1
SCL 5
CN391(NO CONNECTION)
CN391 is used for adjustment at factory
78
15
PROTECT-1PROTECT-2
PROTECT1PROTECT2
RCV-IN
FROM/TOCRT/H.V. BLOCK
OSD-BLK
56
FROM/TOCRT/H.V. BLOCK
TU AUDIO TO AUDIO/POWERCONTROL BLOCK
TOCRT/H.V. BLOCK
BLUE5GREEN4RED3
IF/Video/System Control Block Diagram
VIDEO SIGNALRF/IF SIGNAL AUDIO SIGNAL
REMOTESENSOR
RCV101
P-ON-HP-ON-HSDASCL
35
FROM/TOAUDIO/POWERCONTROL BLOCK RESET30RESET TRAP
SW
34 JK701VIDEO-IN(FRONT)
JK703VIDEO-IN(FRONT)
CN101BCN101AKEY-IN12 2
KEY-IN1
MAIN CBAFUNCTION CBA
6 PROTECT3PROTECT-3
WF2
WF16
WF1
-
Audio/Power Control Block Diagram
MAIN CBA
AUDIO SIGNAL
WF6
6-3 6-4
LIMITER FM DET AFAMP
IC801
IC301
(AMP)
NOTE FOR WIRE CONNECTORS: 1. PREFIX SYMBOL "CN" MEANS CONNECTOR. (CAN DISCONNECT AND RECONNECT.) 2. PREFIX SYMBOL "CL" MEANS WIRE-SOLDER HOLES OF THE PCB. (WIRE IS SOLDERED DIRECTLY.)
TEST POINT INFORMATION:INDICATES A TEST POINT WITH A JUMPER WIRE ACROSS A HOLE IN THE PCB.:USED TO INDICATE A TEST POINT WITH A COMPONENT LEAD ON FOIL SIDE.:USED TO INDICATE A TEST POINT WITH NO TEST PIN.:USED TO INDICATE A TEST POINT WITH A TEST PIN.
SCL
SDA
5
10
47
13
55
46
33
39
42
41
TU AUDIO
P-ON-H
BACK UP
BUSI/F
ATT 50
POWER ONCONTROL
+5.7V REGULATOR
+5V CTRL
+5V CTRL2
+8V CTRL
BACKUPCTRL
TO POWER SUPPLYBLOCK
TO IF/VIDEO/SYSTEM CONTROLBLOCK
7 OUTPUT 1
FROM/TO IF/VIDEO/SYSTEM CONTROLBLOCK
FROM IF/VIDEO/SYSTEM CONTROLBLOCK
L6310BLA
P-ON-ON
P-ON-ON
RESET RESET
BUSCONTROL
VIDEO/AUDIO/CHROMA/DEFLECTION/IF
52JK702AUDIO-IN(FRONT)
JK703AUDIO-IN(REAR)
SP802SPEAKER
CN802A SP-AUDIO 1SP-AUDIO 2
SP801SPEAKER
CN801ASP-AUDIO 1
SP-GND 2
JK801HEADPHONEJACK
JK801HEADPHONEJACK
SP802SPEAKER
CN802A SP-AUDIO 1SP-AUDIO 2
SP801SPEAKER
CN801ASP-AUDIO 1
SP-GND 2
TOEXTERNALSPEAKER(SP811)
CN811BCN811ASP-AUDIO1 1SP-AUDIO3 3
JACK-A CBA
JK811
TOEXTERNALSPEAKER(SP812)
CN812BCN812ASP-AUDIO1 1
SP-AUDIO3 3
JACK-B CBA
JK812
SP-AUDIO2 2
-
7486
11109
V-DRIVE
PROTECT-1
V-RAMP-F/B
H-DRIVE
GREEN AMPBLUE AMP
Q501
Q503
Q572 Q571T572
1
3
4
5
L6310BLCRT
FBPACL/ABL
CRT/H.V. Block Diagram
V-DRIVE
H-DRIVE
DY551 D.Y.
IC551 (V-DEFLECTION CONTROL)
T571 F.B.T.
ANODE
FOCUSSCREEN
MAIN CBA
CRT CBA
CN301B
RGBHEATER
ANODE
GND
V501CRT
FOCUSSCREENGND
JK501
CN501
CN581BCN581A
VIDEO SIGNAL
CN571
FOCUS VR
SCREEN VR
6-5 6-6
H.OUTPUTH.DRIVE
FROM POWER SUPPLY BLOCK +B
X-RAYJ121 J122
Q502
4
3
1
5
S
FHV
11
8
10
7
9
6
PROTECT-3
DEF+B
AMP7
1
6 3
PULSEUP
THERMALPROTECTION
5
WF7 WF8
WF11WF12
WF9
WF10
WF3 WF15 WF4 WF14
WF5 WF13
RED AMP
PROTECT-2
RED 3GREEN 4
BLUE 5
FROM/TO IF/VIDEO/SYSTEM CONTROLBLOCK
FROM/TO IF/VIDEO/SYSTEM CONTROLBLOCK
FROM IF/VIDEO/SYSTEM CONTROLBLOCK
HEATER3 3+160V1 1
TO CN301A
-
4A/125VF6014A/125V
LINEFILTER
L601
JS601
AC601AC CORD
DEGAUSSINGCOIL
DG691CN691
PS691
BRIDGERECTIFIER
D605 - D608
HOT COLDT601
6
4
2
1 11
12
8
10
7
4
3
1
2
IC601ERRORVOLTAGE DET
Q601
Q602LIMITER
SWITCHING
Q662FEEDBACK
VR661+BADJ Q676
SWITCHINGCONTROL
SWITCHINGQ671
Q683
Q682
Q681+8V SWITCHING
+5V SWITCHING
+5V SWITCHING
+5V SWITCHING
MAIN CBA
+B
DEF +B
AL+5V
+5V CTRL2(FROM PIN41 OF IC301)
P-ON+8V
P-ON+5V
P-ON+5V
AL+12V
+5V CTRL(FROM PIN39 OF IC301)
+8V CTRL(FROM PIN33 OF IC301)
L6310BLP6-7 6-8
AL+33V
PROTECT-2(TO PIN8 OF IC101)
BACK-UP
AL+9V
Q121
+9V SWITCHING
Q351
NOTE : The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Power Supply Block Diagram
+BTP601
HOT CIRCUIT. BE CAREFUL.
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4 A, 125V FUSE.
CAUTION:
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 4A, 125V.4A/125V
PROTECT-1(TO PIN7 OF IC101)
CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F601) is blown, check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
-
7-1 L13SC
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTSStandard NotesMany electrical and mechanical parts in this chassis have special characteristics. These characteristics oftenpass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement compo-nents rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics areidentified in this manual and its supplements; electrical components having such features are identified by themark " # " in the schematic diagram and the parts list. Before replacing any of these components, read the partslist in this manual carefully. The use of substitute replacement parts that do not have the same safety characteris-tics as specified in the parts list may create shock, fire, or other hazards.
Note:1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.2. All resistance values are indicated in ohms (K=103, M=106).3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.4. All capacitance values are indicated in F (P=10-6F).5. All voltages are DC voltages unless otherwise specified.
Note of Capacitors: ML --- Mylar Cap. PP --- Metallized Film Cap. SC --- Semiconductor Cap. L --- Low Leakage type
Temperature Characteristics of Capacitors are noted with the following: B --- 10% CH --- 060ppm/C CSL --- +350~-1000ppm/C
Tolerance of Capacitors are noted with the following: Z --- +80~-20%
Note of Resistors: CEM --- Cement Res. MTL --- Metal Res. F --- Fuse Res.
Capacitors and transistors are represented by the following symbols.
(Top View) (Bottom View)
(Bottom View)
Electrolytic Capacitor+
Transistor or Digital Transistor
NPN Transistor PNP Transistor
NPN Digital Transistor PNP Digital Transistor
(Top View)
(Top View)E C B
E C B
Digital Transistor
CBA Symbols Schematic Diagram Symbols
E C B
(Top View)
(Top View)E C B
E C B
-
7-2 L13SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ONTHE FOLLOWING PAGES:1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defectivebefore you connect the AC plug to the AC power supply. Otherwise it may cause some components in the pow-er supply circuit to fail.
3. Note:(1) Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.(2) To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual. 4. Wire Connectors
(1) Prefix symbol "CN" means "connector" (can disconnect and reconnect).(2) Prefix symbol "CL" means "wire-solder holes of the PCB" (wire is soldered directly).
5. Note: Mark "I" is a leadless (chip) component. 6. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
7. How to read converged lines
8. Test Point Information
2 31 5.05.0
Voltage Indicates that the voltageis not consistent here.
(3.0) (3.0) Power on mode Power off mode
Unit: Volts
3
2
1
A B C D
1-B1
1-D3
AREA D3AREA B1
1-D3
Distinction AreaLine Number(1 to 3 digits)
Examples: 1. "1-D3" means that line number "1" goes to area "D3".
2. "1-B1" means that line number "1" goes to area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.: Used to indicate a test point with a component lead on foil side.: Used to indicate a test point with no test pin.: Used to indicate a test point with a test pin.
-
A1
A2
A3
A4
B1
B2
B3
B4
C1
C2
C3
C4
D1
D2
D3
D4
E1
E2
E3
E4
F1
F2
F3
F4
IF SIGNALVIDEO SIGNALAUDIO SIGNAL
Main 1/4 Schematic Diagram
7-3 7-4 L6310SCM1
MAIN 1/4Ref No. Position
IC101 C-3IC151 C-4IC801 D-1
Q121 E-4
CN391 A-4CN101A D-4CN801A E-1CN802A E-2CN811A E-1CN812A E-1
TP300 B-2TP301 A-2
CONNECTORS
TEST POINTS
ICS
TRANSISTOR
-
G1
G2
G3
G4
H1
H2
H3
H4
I1
I2
I3
I4
J1
J2
J3
J4
K1
K2
K3
K4
L1
L2
L3
L4
IF SIGNALVIDEO SIGNALAUDIO SIGNAL
7-5 7-6 L6310SCM2
Main 2/4 Schematic Diagram
MAIN 2/4Ref No. Position
IC301 H-2
Q321 K-1Q351 G-3
TRANSISTOR
IC
-
M1
M2
M3
N1
N2
N3
O1
O2
O3
P1
P2
P3
Q1
Q2
Q3
7-7 7-8 L6310SCM3
Main 3/4 Schematic DiagramMAIN 3/4
Ref No. Position
IC601 P-2
Q601 P-3Q602 P-2Q662 O-1Q671 N-2Q676 N-1Q681 N-2Q682 N-1Q683 N-1
CN691 Q-2
VR661 O-2VARIABLE RESISTOR
IC
TRANSISTORS
CONNECTORS
*1 NOTE:The Capacitor ( C643 ) is either type A or type B.These two types are exchangeable and can be
equally used whichever the model is . The difference between type A and type B is shown in the table below.
Type AType B 4700P/250V
0.01/250V 0.01/250VNot Used
C643 C642 JS642Not Used
WIRE
NOTE :The voltage for parts in hot circuit is measuredusing hot GND as a common terminal.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISKFIRE, REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE.ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DEMME TYPE DE 4A, 125V.4A/125V
CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F601) is blown, check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
-
R1
R2
R3
S1
S2
S3
T1
T2
T3
U1
U2
U3
V1
V2
V3
W1
W2
W3
VIDEO SIGNAL
7-9 7-10 L6310SCM4
Main 4/4 & CRT Schematic DiagramMAIN 4/4
Ref No. Position
IC551 R-3
Q571 T-3Q572 S-3
CN571 S-3CN301A U-2CN581A U-3
TP601 T-2TEST POINT
TRANSISTORS
CONNECTORS
IC
CRTRef No. Position
Q501 U-2Q502 V-2Q503 V-2
CN501 V-2CN301B U-2CN581B U-3
TP501 U-2TP502 U-2
TEST POINTS
TRANSISTORS
CONNECTORS
-
+BTP601
FOCUS-VR(UPPER SIDE)
SCREEN-VR(LOWER SIDE)
GNDTP300
VR661+B ADJ
AGCTP301 D316 Cathode
(C-Trap Adjustment)
R583(Hf0 Adjustment)
Main CBA Top ViewBECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWERSUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUTSLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLYCIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.NOTE :The voltage for parts in hot circuit is measured
using hot GND as a common terminal.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISKFIRE, REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE.ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DEMME TYPE DE 4A, 125V.4A/125V
7-11 BL6310F01011-17-12
CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F601) is blown, check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
MAIN CBARef No. Position
IC101 D-3IC151 D-2IC301 C-1IC551 B-2IC601 C-3IC801 D-1
Q121 D-2Q321 B-2Q351 B-1Q571 B-3Q572 B-2Q601 B-4Q602 C-4Q662 C-3Q671 C-2Q676 D-2Q681 C-2Q682 C-3Q683 C-3
CN391 A-1CN571 A-2CN691 D-4
CN101A D-1CN301A B-2CN581A A-2CN801A D-1CN802A E-4CN811A D-1CN812A E-4
TP300 A-3TP301 A-1TP601 A-4
VR661 A-1
ICS
VARIABLE RESISTOR
CONNECTORS
TEST POINTS
TRANSISTORS
-
Q571Base
WF8
PIN 4OF CN571
WF12
WF9PIN 1OF CN571
PIN 3OF CN581A
WF10
PIN 7OF IC551
WF11
Q572Collector
WF7
WF1PIN 36OF IC301
WF6PIN 50OF IC301WF2PIN 40OF IC301
PIN 8OF TU1
WF16
Main CBA Bottom ViewBECAUSE A HOT CHASSIS GROUND IS PRESENT IN THE POWERSUPPLY CIRCUIT, AN ISOLATION TRANSFORMER MUST BE USED.ALSO, IN ORDER TO HAVE THE ABILITY TO INCREASE THE INPUTSLOWLY, WHEN TROUBLESHOOTING THIS TYPE POWER SUPPLYCIRCUIT, A VARIABLE ISOLATION TRANSFORMER IS REQUIRED.NOTE :
The voltage for parts in hot circuit is measuredusing hot GND as a common terminal.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISKFIRE, REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE.ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DEMME TYPE DE 4A, 125V.4A/125V
7-13 7-14 BL6310F01011-1
CAUTION !Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit.If Main Fuse (F601) is blown, check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
-
WF13Q503Collector
Q503Base
WF5WF14Q502Collector
Q502Base
WF4 WF15Q501Collector
Q501Base
WF3
7-15 BL6310F01021-27-16
CRT CBA Top View CRT CBA Bottom View
CRT CBARef No. Position
Q501 B-1Q502 B-1Q503 A-1
CN501 A-1CN301B B-1CN581B A-1
TP501 B-1TP502 B-1
TRANSISTORS
CONNECTORS
TEST POINTS
-
FUNCTION CBA Top View FUNCTION CBA Bottom View
BL6310F01021-1
JACK-A CBA Top View
JACK-B CBA Top View
JACK-A CBA Bottom View
JACK-B CBA Bottom View
BL6310F01021-3
BL6310F01021-4
7-17 7-18
-
10 V 5 ms
1DIV: 0.5V 20secIC 301 Pin 36
WF1
GND
1DIV: 0.5V 20secIC 301 Pin 40
WF2 1DIV: 0.2V 20msecIC 301 Pin 50
WF6
1DIV: 200V 20secCN 571 Pin 1
WF9
GND
1DIV: 5V 20secCN581A Pin 3
WF10
GND
1DIV: 2V 5msecIC 551 Pin 7
WF11
1DIV: 10V 5msecCN 571 Pin 4
WF12
1DIV: 20V 20secQ 502 Collector
WF14
1DIV: 2V 20secQ501 Base
WF3
GND
1DIV: 2V 20secQ 502 Base
WF4
1DIV: 2V 20secQ 503 Base
WF5
GND
1DIV: 10V 20secQ 572 Collector
WF7
GND
1DIV: 5V 20secQ 571 Base
WF8
1DIV: 20V 20sec Q503 Collector
WF13
1DIV: 20V 20secQ 501 Collector
WF15
1DIV: 0.2V 20secTU 1 Pin 8
WF16
GND
L6310WF
WF1 ~ WF16 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.)
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)INITIAL POSITION: Unplug unit from AC outlet for at least 5 minutes. reconnect to AC outlet and then turn power on. (Brightness---Center Color---Center Tint --- Center Contrast---Approx 70%)
WAVEFORMS
8-1 8-2
-
9-1 9-2
WIRING DIAGRAM
L6310WI
FUNCTION CBA
CN101A CN101BGND 11KEY-IN1 22NU 33NU 44
CRT CBA
FOCUS
SCREEN
GND
D.Y.
HD
VD
MAIN CBABL6310F01011-1
CN301A
CN501
12
CN691
CLN551
CLN501
CLN301
CLN801
AC601
54321
12345
CN571
12345
CN301B
GNDRED
GREENBLUE
CRT
ANODE
SP801SPEAKER
CN801A
T571FBT
TU1 TUNER UNIT
CN581AWH581B
+8VGNDREDGREENBLUE
+8V
+160V12 GND3
+160V 1
3HEATER2
CN391(NO CONNECTION)
CN391 IS USED FOR ADJUSTMENT AT FACTORY
SD1I2C-OPEN2GND3SDA4SCL5
GNDHEATER
V501
DY551
BL6310F01021-2
1 SP-AUDIO2 SP-GND
CLN802SP802SPEAKER
CN802A1 SP-AUDIO2 SP-AUDIO
JACK-A CBA
CN811A CN811BSP-AUDIO 11GND 22SP-AUDIO 33
JACK-B CBA
CN812A CN812BSP-AUDIO 11SP-AUDIO 22SP-AUDIO 33
BL6310F01021-1
BL6310F01021-3
BL6310F01021-4
JK811
JK812
TOEXTERNALSPEAKER(SP811)
TOEXTERNALSPEAKER(SP812)
-
10-1 L6310PIN
IC PIN FUNCTIONSIC101(TV Micro Computer)Pin No. Signal Name Function
1 H-SYNC H-SYNC Input2 V-SYNC V-SYNC Input3 N.U. Not Used4 N.U. Not Used5 SD Detection SD Signal6 PROTECT-3 Power Supply Protection7 PROTECT-2 Power Supply Protection8 PROTECT-1 Power Supply Protection9 KEY-IN 1 Key Input 1 (Main)10 N.U. Not Used11 N.U. Not Used12 EXT-H EXT-H13 N.U. Not Used14 N.U. Not Used15 RCV-IN Input For Remote Control16 N.U. Not Used17 N.U. Not Used18 VCC AL+5V19 HLF Filter for CCD20 N.U. Not Used21 V-HOLD V-HOLD22 CVIN Input for Video Signal23 CNVSS GND24 X-IN Main Clock Input25 X-OUT Main Clock Output26 VSS GND27 VCC AL+5V28 OSD1 OSD129 OSD2 OSD230 RESET RESET31 N.U. Not Used32 SPOT-KILL Counter-measure for Spot33 N.U. Not Used34 N.U. Not Used35 P-ON-H Output for P-ON-H36 N.U. Not Used
37 SDA I2C-BUS Controller Interface (Data)38 I2C OPEN White Balance Adjustment Judgement39 SCL I2C-BUS Controller Interface (Clock)40 N.U. Not Used41 N.U. Not Used42 N.U. Not Used43 N.U. Not Used44 A-MUTE Audio Mute45 N.U. Not Used46 N.U. Not Used47 N.U. Not Used48 N.U. Not Used49 OSD-BLK Output for Picture Cut off50 OSD-B Blue Output51 OSD-G Green Output52 OSD-R Red Output
Pin No. Signal Name Function
-
CRT CBA
ANODE CAPPart of Flyback Transformer
DY551
Details for DY551 and surrounding parts
SCOTCH TAPE #880
DG691
DY551
V501-1
SHINWHA TAPE SGT-730(WHITE)
SHINWHA TAPE SGT-730(BLACK)
V501-2
B-2
A-6
A-7
A-9A-4
A-3
A-8
L-1
L-5
L-5
L-1A-1
A-12A-14
A-5
B-2
B-2
B-2
B-8
B-1B-8
B-6L-1
L-1
B-7
L-1
L-1
L-1
B-3
B-4
B-5
B-9
B-9
L-1
L-1
L-2
L-2
L-4
L-3
L-2
L-1
A-10A-2
A-13
A-11
CLN551
CLN801
CLN802
SP802
SP801
A-16
A-15
A-16
A-15
CLN811
CLN812
SP812
SP811
L-7L-8
A-17
A-18
MAIN CBA
JACK A CBA
JACK B CBA
EXPLODED VIEWSCabinet
11-1 11-2 L6310CEX
-
Packing
11-3 11-4 L6310PEX
S-5
S-1
Packing Tape
Packing Tape
FRONT
Tape
Tape
Tape
Ear Speaker Assembly
Tape
Shoes
X-4
X-5X-1X-2
B-7
B-8
B-6
X-3
X-6
L
L
R
R
S-2 S-2
S-6
S-3
S-3
S-4
X-5
-
DT1300-C/P/A(L6310UL/11UM
/12UN)2003/1/21D
T1300-C/P/A (L6310UL/11UM/12UN)
AD
T1300-C (L6310UL)B
DT1300-P (L6311UM)
CD
T1300-A (L6312UN)R
ef N
o.M
ark
Descriptio
nParts N
o.M
ECHANICAL PARTS LIST
A-1A
FRONT
CABINET
L6310UL0EM
000759A-1
BFRO
NT CABIN
ET L6311UM
0EM101284
A-1C
FRONT
CABINET
L6312UN0EM
101286A-2
AR
EAR CABIN
ET L6310UL
0EM000760
A-2B
REAR
CABINET
L6311UM0EM
101285A-2
CR
EAR CABIN
ET L6312UN
0EM101287
A-3A,C
SPEAKER GRILL(L)
L6310UL0EM
201691A-3
BSPEAKER G
RILL(L) L6311UM
0EM407970
A-4A,C
SPEAKER GRILL(R)
L6310UL0EM
201692A-4
BSPEAKER G
RILL(R) L6311UM
0EM407971
A-5A
KEY FRAM
E L6310UL0EM
101279A-5
BKEY FR
AME L6311UM
0EM407972
A-5C
KEY FRAM
E L6312UN0EM
407985A-6
ASHO
ES(L) L6310UL
0EM201693
A-6B
SHOES(L)
L6311UM0EM
407973A-6
CSHO
ES(L) L6312UN
0EM407986
A-7A
SHOES(R)
L6310UL0EM
201694A-7
BSHO
ES(R) L6311UM
0EM407974
A-7C
SHOES(R)
L6312UN0EM
407987A-8
AFO
OT
FRONT(L)
L6310UL0EM
301795A-8
BFO
OT
FRONT(L)
L6311UM0EM
407975A-8
CFO
OT
FRONT(L)
L6312UN0EM
407988A-9
AFO
OT
FRONT(R)
L6310UL0EM
301796A-9
BFO
OT
FRONT(R)
L6311UM0EM
407976A-9
CFO
OT
FRONT(R)
L6312UN0EM
407989A-10
AFO
OT
REAR(L)
L6310UL0EM
301797A-10
BFO
OT
REAR(L)
L6311UM0EM
407977A-10
CFO
OT
REAR(L)
L6312UN0EM
407990A-11
AFO
OT
REAR(R)
L6310UL0EM
301798A-11
BFO
OT
REAR(R)
L6311UM0EM
407978A-11
CFO
OT
REAR(R)
L6312UN0EM
407991A-12
SENSOR
LENS L6310UL0EM
301799A-13
AR
ATING LABEL L6310UL
----------
A-13B
RATING
LABEL L6311UM----------
A-13C
RATING
LABEL L6312UN----------
A-14A,C
EAR SPEAKER G
RILL(L) L6310UL
0EM000761
A-14B
EAR SPEAKER G
RILL(L) L6311UM
0EM301814
A-15A,C
EAR SPEAKER G
RILL(R) L6310UL
0EM000762
A-15B
EAR SPEAKER G
RILL(R) L6311UM
0EM301815
A-16!A
EAR SPEAKER RING
L6310UL0EM
301794A-16!
BEAR
SPEAKER RING L6311UM
0EM407969
A-16!C
EAR SPEAKER RING
L6312UN0EM
407982A-17
A,CEAR
SPEAKER REAR(L) L6310UL
0EM101278
A-17B
EAR SPEAKER REAR(L)
L6311UM0EM
301816A-18
A,CEAR
SPEAKER REAR(R) L6310UL
0EM101288
A-18B
EAR SPEAKER REAR(R)
L6311UM0EM
301821B-1
TENSION
SPRING B0080B0:EM
4080826W
H006B-2
CRT M
OUNTING
SCREW L8810JA
0EM403023
1 / 17 pag
e
DT1300-C/P/A(L6310UL/11UM
/12UN)
B-3PCB HO
LDER(L)
L6310UL0EM
201695B-4
PCB HOLD
ER(R) L6310UL
0EM201696
B-5NUT
PLATE L6310UL0EM
301800B-8!
DEG
AUSS HOLD
ER L7530RA
0EM402001
B-9D
ECOR
ATION
SCREW L6310UL
0EM407956
CLN551CRT
GND W
IRE CRT G
NDW
X1L7720-001CLN801
WIR
E ASSEMBLY
WX1L9200-001
CLN802W
IRE ASSEM
BLY SPEAKER WIR
E(180MM)
WX1L1131-001
CLN811W
IRE ASSEM
BLY WX1L6310-006
WX1L6310-006
CLN812W
IRE ASSEM
BLY WX1L6310-006
WX1L6310-006
DG691!
DEG
AUSSING CO
IL F-017
LLBH00ZTM017
DG691!
DEG
AUSSING CO
IL AVDG
013LLBH00ZW
R017DG
691!DEG
AUSSING CO
ILLLBH00ZTZ017
DG691!
DEG
AUSSING CO
IL LLBH00ZTM
022LLBH00ZTM
022L-1
SCREW, P-TIG
HT 3X12 BIN
D H
EAD+
GBM
P3120L-2
SCREW, P-TIG
HT 4X18 BIN
D H
EAD +
GBM
P4180L-3
SCREW, P-TIG
HT 3X12 BIN
D H
EAD+
BLKG
BKP3120L-4
SCREW TAPPING
M4X14
DBU14140
L-5P-TIG
HT SCREW
3X8 BIND
+G
BMP3080
L-7SCREW
, ASSEM
BLED 12:M
3X140EM
404416L-8
SCREW, P-TIG
HT 3X12 BIN
D H
EAD+
GBM
P3120S-1
ACARTO
N L6310UL
0EM301824
S-1B
CARTON
L6311UM0EM
407981S-1
CCARTO
N L6312UN
0EM407994
S-1TO
P COVER
L8500RZ0EM
402939S-2
STYROFO
RM TO
P L6310UL0EM
000763S-2
TOP/BO
TTOM
PAD L6100UZ
0EM406822
S-3STYRO
FORM
BOTTO
M L6310UL
0EM000764
S-3PAR
TITION(A)
L6100UZ0EM
406820S-4
SET SHEET
L6000UA:700X12000EM
407141S-4
PARTITIO
N(B) L6100UZ
0EM406821
S-5A
SERIAL NO. LABEL L6310UL
----------
S-5B
SERIAL NO. LABEL L6311UM
----------
S-5C
SERIAL NO. LABEL L6312UN
----------
S-6HO
LD PAD
L6310UL0EM
408005S-6
SHIPPING CABIN
ET(A) L1400UZ
0EM406296
S-7SHIPPING
CABINET(B)
L1400UZ0EM
406297S-8
PALLET0VM
301902SP801
SPEAKER S0407F02ADSD0407XQ
001SP802
SPEAKER S0407F02ADSD0407XQ
001SP811
SPEAKER S08F04DSD0408XQ
004SP812
SPEAKER S08F04DSD0408XQ
004X-1
AR
EMO
TE CO
NTRO
L NE117UD
NE117UD
X-1B
REM
OTE
CON
TROL N
E118UDN
E118UDX-1
CR
EMO
TE CO
NTRO
L NE119UD
NE119UD
X-2DRY BATTERY R6P UM
3XB0M
451GH001
X-2D
RY BATTER
Y R6P/2SXB0M
451T0001X-2
DR
Y BATTERY(SUNRISE)
R6SSE/2SXB0M
451MS002
X-2DRY BATTER
Y R6P(AR)2PXXB0M
451HU002X-2
DRY BATTERY R6P(AR)2P X
ICIXB0M
451HU003X-3!
OW
NER
'S MANUAL(E)/(S)
L6310UL:ENGLISH/SPANISH
0EMN02100
X-4PO
LYETHYLEN
E BAG F8626B5
Z325350X-5
BAG (C)
50X80X0.05Z505080
X-6PO
LY BAG 100X220X0
.03TZ310220
X-7PO
LYETHYLEN
E BAG F8626B5
Z325350CRT
TYPE AD
Y551!D
EFLECTION
YOKE KD
Y3GDA82X
LLBY00ZMS011
2 / 17 pag
e
-
DT1300-C/P/A(L6310UL/11UM
/12UN)
DY551!
DEFLECTIO
N YO
KE LLBY00ZSY005LLBY00ZSY005
V501!CRT
A34AGT13X
TCRT190CP036V501-1
C.P.MAG
NET JH225-FN
-00XM
04000BV003V501-2
WEDG
E FT-00110W
XV10000T4001V501-2
WEDG
E DB25SR
XV10000D9001CRT
TYPE BD
Y551!D
EFLECTION
YOKE LLBY00ZSY002
LLBY00ZSY002D
Y551!D
EFLECTION
YOKE CDY-M
1456SLLBY00ZQ
S008D
Y551!D
EFLECTION
YOKE KD
Y3GC
734XLLBY00ZM
S006D
Y551!D
EFLECTION
YOKE KD
Y3GCE83X
LLBY00ZMS027
V501!CRT
A34KQW
42XTCRT190SM
013V501-1
C.P.MAG
NET JH225-014
XM04000BV009
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE C
DY551!
DEFLECTIO
N YO
KE KDY3G
D591X
LLBY00ZMS005
DY551!
DEFLECTIO
N YO
KE CDY-M1422F
LLBY00ZQS001
V501!CRT
A34JLL90X(W)
TCRT190QS015
V501-1C.P.M
AGNET
JH225-FN-00
XM04000BV003
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE D
DY551!
DEFLECTIO
N YO
KE LLBY00ZSY003LLBY00ZSY003
DY551!
DEFLECTIO
N YO
KE KDY3G
D592X
LLBY00ZMS004
DY551!
DEFLECTIO
N YO
KE CDY-M1455F
LLBY00ZQS007
V501!CRT
A34LRQ90X(VW
)TCRT190P7003
V501-1C.P.M
AGNET
JH225-FN-00
XM04000BV003
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE E
DY551!
DEFLECTIO
N YO
KE LLBY00ZSY002LLBY00ZSY002
DY551!
DEFLECTIO
N YO
KE KDY3G
C587X
LLBY00ZMS003
DY551!
DEFLECTIO
N YO
KE CDY-M1456S
LLBY00ZQS008
DY551!
DEFLECTIO
N YO
KE KDY3G
CE83XLLBY00ZM
S027V501!
CRT A34KPU02XX
TCRT190GS016
V501-1C.P.M
AGNET
JH225-FN-00
XM04000BV003
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE F
DY551!
DEFLECTIO
N YO
KE KDY3G
CB05XLLBY00ZM
S014D
Y551!D
EFLECTION
YOKE ST14PW
RF01LLBY00ZSAM
01V501!
CRT A34LEX10X
TCRT190SAM01
V501-1C.P.M
AGNET
JH225-FN-00
XM04000BV003
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE G
DY551!
DEFLECTIO
N YO
KE LLBY00ZSY002LLBY00ZSY002
DY551!
DEFLECTIO
N YO
KE KDY3G
CB82XLLBY00ZM
S018D
Y551!D
EFLECTION
YOKE KD
Y3GCE83X
LLBY00ZMS027
V501!CRT
A34JQQ093X
TCRT190MS010
V501-1C.P.M
AGNET
JH225-FN-00
XM04000BV003
V501-2W
EDGE FT
-00110WXV10000T4001
V501-2W
EDGE D
B25SRXV10000D9001
CRT TYPE H
V501!CRT
A34JXV70XTCRT190TH
A02V501-2
WEDG
E FT-00110W
XV10000T4001V501-2
WEDG
E DB25SR
XV10000D9001
3 / 17 pag
e
DT1300-C/P/A(L6310UL/11UM
/12UN)
ELECTRICAL PARTS
LISTA
MM
A CBA
0ESA05306B
MM
A CBA
0ESA05458 C
MM
A CBA
0ESA05460 AC601!
AC COR
D LA-2413
WAC0172LW
007B-6
HEAT
SINK(PG
B) L6000UZ
0EM406788
B-7H
EAT SIN
K(PFZ) L6100UZ
0EM406786
B-12CLO
TH(65) L7735TR
:65X10X0.5T0EM
402149BC101
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC571
BEAD IN
DUCTORS FBA04HA600VB-00
LLBF00STU026BC601
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC602
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC651
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC652
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC653
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC691
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021BC692
BEAD IN
DUCTORS FBR07HA121TB-00
LLBF00ZTU021C5
ELECTROLYTIC
CAP. 100UF/10V M
CE1AMASTL101
C5ELECTRO
LYTIC CAP.
100UF/10V MCE1AM
ASDL101C6
ELECTROLYTIC
CAP. 4.7UF/50V M
CE1JMASTL4R
7C6
ELECTROLYTIC
CAP. 4.7UF/50V M
CE1JMASDL4R7
C103CERAM
IC CAP.(AX) CH J 12PF/50V
CCA1JJTCH120C104
CERAMIC CAP.(AX)
CH J 12PF/50VCCA1JJTCH120
C121ELECTRO
LYTIC CAP
. 47UF/16V
MCE1CM
ASTL470C121
ELECTROLYTIC
CAP. 47UF/16V
MCE1CM
ASDL470C125
CERAMIC CAP.(AX)
F Z 0.01UF/25VCDA1EZT0F103
C126CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C127
CHIP CERAMIC CAP.
F Z 0.1UF/25VCHD1EZ30F104
C141CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C142
ELECTROLYTIC
CAP. 100UF/10V M
CE1AMASTL101
C142ELECTRO
LYTIC CAP.
100UF/10V MCE1AM
ASDL101C151
CERAMIC CAP.(AX)
F Z 0.01UF/25VCDA1EZT0F103
C152CHIP CERAM
IC CAP.(MELF)
B K 220PF/50VCZM
1JK30B221C152
CHIP CERAMIC CAP.
CH J 220PF/50VCHD1JJ3CH221
C153CHIP CERAM
IC CAP.(MELF)
B K 220PF/50VCZM
1JK30B221C153
CHIP CERAMIC CAP.
CH J 220PF/50VCHD1JJ3CH221
C154CERAM
IC CAP.(AX) F Z 0.1UF/50V
CA1J104TU014C154
CERAMIC CAP.(AX)
F Z 0.1UF/50VCCA1JZT0F104
C155ELECTRO
LYTIC CAP
. 47UF/16V
MCE1CM
ASTL470C155
ELECTROLYTIC
CAP. 47UF/16V
MCE1CM
ASDL470C162
CHIP CERAMIC CAP.(M
ELF) B K 220PF/50V
CZM1JK30B221
C162CHIP CERAM
IC CAP. CH J 220PF/50V
CHD1JJ3CH221C163
ELECTROLYTIC
CAP. 0.1UF/50V M
CE1JMASTLR
10C163
ELECTROLYTIC
CAP. 0.1UF/50V M
CE1JMASDLR10
C163ELECTRO
LYTIC CAP.
0.1UF/50V MCE1JM
ASDL0R1C164
FILM CAP.(P)
0.001UF/50V JCM
A1JJS00102C164
FILM CAP.(P)
0.001UF/50V JCA1J102M
S029C301
CERAMIC CAP.(AX)
F Z 0.1UF/50VCA1J104TU014
C301CERAM
IC CAP.(AX) F Z 0.1UF/50V
CCA1JZT0F104C302
ELECTROLYTIC
CAP. 220UF/10V M
CE1AMASTL221
C302ELECTRO
LYTIC CAP.
220UF/10V MCE1AM
ASDL221C303
CERAMIC CAP.(AX)
B K 0.01UF/50VCA1J103TU011
C308CHIP CERAM
IC CAP. B K 0.01UF/50V
CHD1JK30B103C309
ELECTROLYTIC
CAP. 1UF/50V
MCE1JM
ASTL1R0C309
ELECTROLYTIC
CAP. 1UF/50V
MCE1JM
ASDL1R0C309
ELECTROLYTIC
CAP. 1UF/50V
MCE1JM
ASDL010
4 / 17 pag
e
-
DT1300-C/P/A(L6310UL/11UM
/12UN)
C321ELECTRO
LYTIC CAP.
100UF/10V MCE1AM
ASTL101C321
ELECTROLYTIC
CAP. 100UF/10V M
CE1AMASDL101
C322CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C323
FILM CAP.
0.47UF/50V J122Z317S
C323TF
CAP. 0.47UF/50V J
CT1J474MS045
C324CERAM
IC CAP.(AX) F Z 0.01UF/25V
CDA1EZT0F103C325
CHIP CERAMIC CAP.(M
ELF) F Z 0.01UF/16V
CZM1CZ30F103
C326CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C327
CHIP CERAMIC CAP.
CH J 47PF/50VCHD1JJ3CH470
C328ELECTRO
LYTIC CAP
. 10UF/50V
MCE1JM
ASTL100C328
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASDL100C329
ELECTROLYTIC
CAP. 100UF/10V M
CE1AMASTL101
C329ELECTRO
LYTIC CAP.
100UF/10V MCE1AM
ASDL101C332
CHIP CERAMIC CAP.
F Z 0.1UF/25VCHD1EZ30F104
C334ELECTRO
LYTIC CAP.
2.2UF/50V MCE1JM
ASTL2R2
C334ELECTRO
LYTIC CAP.
2.2UF/50V MCE1JM
ASDL2R2C345
CHIP CERAMIC CAP.
B K 0.015UF/50VCHD1JK30B153
C346ELECTRO
LYTIC CAP
. 1UF/50V
MCE1JM
ASTL1R0C346
ELECTROLYTIC
CAP. 1UF/50V
MCE1JM
ASDL1R0C346
ELECTROLYTIC
CAP. 1UF/50V
MCE1JM
ASDL010C348
ELECTROLYTIC
CAP. 0.1UF/50V M
CE1JMASTLR
10C348
ELECTROLYTIC
CAP. 0.1UF/50V M
CE1JMASDLR10
C348ELECTRO
LYTIC CAP.
0.1UF/50V MCE1JM
ASDL0R1C349
CHIP CERAMIC CAP.
F Z 0.1UF/25VCHD1EZ30F104
C352CHIP CERAM
IC CAP. B K 0.047UF/50V
CHD1JK30B473C352
CHIP CERAMIC CAP.
B K 0.047UF/25VCHD1EK30B473
C353ELECTRO
LYTIC CAP
. 10UF/50V
MCE1JM
ASTL100C353
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASDL100C354
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASTL100C354
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASDL100C355
ELECTROLYTIC
CAP. 4.7UF/50V M
CE1JMASTL4R
7C355
ELECTROLYTIC
CAP. 4.7UF/50V M
CE1JMASDL4R7
C356ELECTRO
LYTIC CAP.
470UF/10V MCE1AM
ASTL471C356
ELECTROLYTIC
CAP. 470UF/10V M
CE1AMASDL471
C358ELECTRO
LYTIC CAP.
0.47UF/50V MCE1JM
ASTLR47
C358ELECTRO
LYTIC CAP.
0.47UF/50V MCE1JM
ASDLR47C364
ELECTROLYTIC
CAP. 2.2UF/50V M
CE1JMASTL2R
2C364
ELECTROLYTIC
CAP. 2.2UF/50V M
CE1JMASDL2R2
C371CERAM
IC CAP.(AX) SL J 47PF/50V
CCA1JJTSL470C372
CERAMIC CAP.(AX)
SL J 47PF/50VCCA1JJTSL470
C374ELECTRO
LYTIC CAP.
2.2UF/50V M LL
CE1JMASLL2R2
C374ELECTRO
LYTIC CAP.
2.2UF/50V LLCE1JM
ASLH2R2C377
CERAMIC CAP.(AX)
X K 3900PF/16V
CDA1CKT0X392C381
CHIP CERAMIC CAP.
B K 0.01UF/50VCHD1JK30B103
C382CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C384
CHIP CERAMIC CAP.(M
ELF) SL J 100PF/50V
CZM1JJ3SL101
C384CHIP CERAM
IC CAP. CH J 100PF/50V
CHD1JJ3CH101C385
ELECTROLYTIC
CAP. 0.47UF/50V M
CE1JMASTLR
47C385
ELECTROLYTIC
CAP. 0.47UF/50V M
CE1JMASDLR47
C386CHIP CERAM
IC CAP.(MELF)
F Z 0.01UF/16VCZM
1CZ30F103C387
CERAMIC CAP.(AX)
B K 0.047UF/50VCA1J473TU011
C551ELECTRO
LYTIC CAP
. 47UF/35V
MCE1G
MASTL470
C551ELECTRO
LYTIC CAP
. 47UF/35V
MCE1G
MASDL470
C552FILM
CAP.(P) 0.1UF/50V J
CMA1JJS00104
C552FILM
CAP.(P) 0.1UF/50V J
CA1J104MS029
C554ELECTRO
LYTIC CAP.
100UF/35V MCE1G
MASTL101
C554ELECTRO
LYTIC CAP.
100UF/35V MCE1G
MASDL101
5 / 17 pag
e
DT1300-C/P/A(L6310UL/11UM
/12UN)
C562ELECTRO
LYTIC CAP
. 1UF/50V
M LL
CE1JMASLL1R0
C562ELECTRO
LYTIC CAP
. 1UF/50V
LLCE1JM
ASLH1R0C566
ELECTROLYTIC
CAP. 1000UF/25V M
CE1EMZN
TL102C566
ELECTROLYTIC
CAP. 1000UF/25V M
CE1EMZPD
L102C566
ELECTROLYTIC
CAP. 1000UF/25V M
CE1EMZAD
L102C568
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASTL100C568
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASDL100C571!
PP CAP. 0.33UF/250V J
CT2E334MS041
C571!P.P.
CAP 0.33UF/200V JCA2D334VC012
C571!M
ETALLIZED FILM
CAP. 0.33UF/200V J
CT2D334F7001C574
ELECTROLYTIC
CAP. 4.7UF/250V M
CE2EMASDL4R7
C577ELECTRO
LYTIC CAP
. 47UF/35V
MCE1G
MASTL470
C577ELECTRO
LYTIC CAP
. 47UF/35V
MCE1G
MASDL470
C578FILM
CAP.(P) 0.01UF/50V J
CMA1JJS00103
C578FILM
CAP.(P) 0.01UF/50V J
CA1J103MS029
C580!PP CAP.
0.0082UF/1.6KV JCT3C822M
S039C580!
PP CAP. 0.0082UF/1.6KV J
CBH3CJQ00822
C580!P.P.
CAP 0.0082UF/1.6K JCA3C822VC011
C580!M
ETALLIZED FILM
CAP. 0.0082UF/1.6KV J
CT3C822F7002C584!
ELECTROLYTIC
CAP. 1UF/160V M
CE2CMASTL1R0
C584!ELECTRO
LYTIC CAP.
1UF/160V MCE2CM
ASDL1R0C594!
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASTL100C594!
ELECTROLYTIC
CAP. 10UF/50V
MCE1JM
ASDL100C601!
METALLIZED
FILM CAP.
0.1UF/250VCT2E104M
S037C601!
FILM CAP.(M
P) 0.1UF/250V K
CT2E104DC011C601!
METALLIZED
FILM CAP.
0.1UF/275V KCT2E104HJE06
C605CERAM
IC CAP. F Z 0.01UF/500V
CCD2JZP0F103C605
CERAMIC CAP.
0.01UF/AC250VCCD2EZA0F103
C606CERAM
IC CAP. F Z 0.01UF/500V
CCD2JZP0F103C606
CERAMIC CAP.
0.01UF/AC250VCCD2EZA0F103
C609CERAM
IC CAP. B K 1000PF/2KV
CCD3DKD0B102C609
CERAMIC CAP.
B K 1000PF/2KVCCD3DK
top related