edge deskwrap screen installation guide › files › gi0018_-_deskwrap_screen... · 2020-06-24 ·...

Edge Deskwrap Screen Installation Guide – Rev A

E D G E D E S K W R A P S C R E E N I N S T A L L A T I O N G U I D E

S C R E E N A C C E S S O R I E S

G I 0 0 1 8

2

I N S T A L L A T I O N G U I D E

S C R E E N S O V E R V I E W

Acrylic – Removable (pages 6-8)

Acoustic – Removable (pages 12-14)

Acoustic with Roof – Removable (pages 18-20)

Acrylic – Fixed (pages 9-11)

Acoustic – Fixed (pages 15-17)

Acoustic with Roof – Fixed (pages 21-23)

3

I N S T A L L A T I O N G U I D E

1 ) P A R T S A N D F A S T E N E R S I N C L U D E D

Side Screen (2x)

Clamp Bracket (6x)

Outer Corner Bracket (4x)

Rear Screen Fixed Mount Bracket (6x)

Outer Bayonet Plate (6x)

Knob (6x)

Inner Corner Bracket (4x)

1/4-20 x 5/16 Button Head Hex Drive Screw (32x)

4

I N S T A L L A T I O N G U I D E

1 ) P A R T S A N D F A S T E N E R S I N C L U D E D C O N T .

#12 x ½” Pan Head PhillipsDrive Screw (32x)

#10 x 1” Pan Head PhillipsScrew (24x)

#8 x ¾” Pan Head PhillipsScrew (24x)

5

I N S T A L L A T I O N G U I D E

2 ) T O O L S A N D S U P P L I E S R E Q U I R E D

Drill/Driver

5/32 Hex Drive Bit

Level

Phillips Bit Square Bit

5/32 Allen Wrench Tape Measure

6

I N S T A L L A T I O N G U I D E

1. Remove the protective film from the Acrylic Screens.

2. Align the Acrylic Screen holes over the OuterBayonet Plate and bolt the Clamp Bracket using theprovided ¼ 20 x 5/16” Button Head Hex Drive Screws.

Note: There should be a left hand and right hand sidescreen when complete.

3. Screw the provided Knobs onto the Clamp Brackets.

F I G U R E 3 . 0

F I G U R E 3 . 1

F I G U R E 3 . 2

3 ) A S S E M B L Y : A C R Y L I C R E M O V A B L E S C R E E N

6x

6x

7

I N S T A L L A T I O N G U I D E

4. Loosely attach the Rear Screen assembly to the rear of the worksurface, centering as best as possible

Note: The Clamp Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

5. Loosely attach the Side Screen assembly, lining up the Rear Screen edges.

Note: The Clamp Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

6. Align the Acrylic Screen holes over the Outer CornerBracket and bolt the Inner Corner Bracket using the provided ¼ 20 x 5/16” Button Head Hex Drive Screws

F I G U R E 3 . 3

F I G U R E 3 . 4

F I G U R E 3 . 5

3 ) A S S E M B L Y : A C R Y L I C R E M O V A B L E S C R E E N

4x

8

I N S T A L L A T I O N G U I D E

7. Once the screen is in the desired position, turn the knob until it touches the underside of the worksurface, snuggly.

Note: Once the knob touches the worksurface, only 1 full turn is needed. DO NOT OVER TIGHTEN.

8. Enjoy!

F I G U R E 3 . 6

F I G U R E 3 . 7

3 ) A S S E M B L Y : A C R Y L I C R E M O V A B L E S C R E E N

6x

9

I N S T A L L A T I O N G U I D E

1. Remove the protective film from the Acrylic Screens

2. Align the Acrylic Screen holes over the OuterBayonet Plate and bolt the Fixed Mount Bracket using the provided ¼ 20 x 5/16” Button Head Hex Drive Screws.

Note: There should be a left hand and right hand side screen when complete.

3. Position the Rear Screen assembly to the rear of the worksurface, on center.

Note: The Fixed Mount Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

F I G U R E 4 . 0

F I G U R E 4 . 1

F I G U R E 4 . 2

4 ) A S S E M B L Y : A C R Y L I C F I X E D S C R E E N

6x

10

I N S T A L L A T I O N G U I D E

4. Once the screen is in the desired position, attach theFixed Mount Bracket to the underside of theworksurface using the screws provided.

Note: Use the correct length screw depending on theworksurface thickness: #10 x 1” or #8 x ¾”

5. Position the Side Screen assembly with the RearScreen edges.

Note: The Fixed Mount Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

6. Once the screen is in the desired position, attach the Fixed Mount Bracket to the underside of the worksurface using the screws provided.

Note: Use the correct length screw depending on the worksurface thickness: #10 x 1” or #8 x ¾”

F I G U R E 4 . 3

F I G U R E 4 . 4

F I G U R E 4 . 5

4 ) A S S E M B L Y : A C R Y L I C F I X E D S C R E E N

2x

4x

11

I N S T A L L A T I O N G U I D E

7. Align the Acrylic Screen holes over the Outer CornerBracket and bolt the Inner Corner Bracket using theprovided ¼ 20 x 5/16” Button Head Hex Drive Screws.

8. Enjoy!

F I G U R E 4 . 6

F I G U R E 4 . 7

4 ) A S S E M B L Y : A C R Y L I C F I X E D S C R E E N

4x

12

I N S T A L L A T I O N G U I D E

1. Align the Clamp Bracket over the marked holelocations of the Acoustic Screens and attach using theprovided #12 x ½” Pan Head Phillips Drive Screws.

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Note: There should be a left hand and right hand sidescreen when complete.

2. Screw the provided Knobs onto the Clamp Brackets.

3. Loosely attach the Rear Screen assembly to the rear of the worksurface , centering as best as

Note: The Clamp Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

F I G U R E 5 . 0

F I G U R E 5 . 1

F I G U R E 5 . 2

5 ) A S S E M B L Y : A C O U S T I C R E M O V A B L E S C R E E N

6x

6x

13

I N S T A L L A T I O N G U I D E

4. Loosely attach the Side Screen assembly, lining upthe Rear Screen edges.

Note: The Clamp Bracket must not interfere with anypart of the table understructure. This may require theunderstructure to be re positioned.

5. Align the Inner Corner Bracket over the marked holelocations of the Acoustic Screens and attach using theprovided #12 x ½”. Pan Head Phillips Drive Screws

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Tip: These brackets should be installed in the top &bottom corners

6. Once the screen is in the desired position, turn the knob until it touches the underside of the worksurface, snuggly.

Note: Once the knob touches the worksurface, only 1 full turn is needed. DO NOT OVER TIGHTEN.

F I G U R E 5 . 3

F I G U R E 5 . 4

F I G U R E 5 . 5

5 ) A S S E M B L Y : A C O U S T I C R E M O V A B L E S C R E E N

4x

6x

14

I N S T A L L A T I O N G U I D E

7. Enjoy!

F I G U R E 5 . 6

5 ) A S S E M B L Y : A C O U S T I C R E M O V A B L E S C R E E N

15

I N S T A L L A T I O N G U I D E

1. Align the Clamp Bracket over the marked holelocations of the Acoustic Screen and attach using theprovided #12 x ½” Pan Head Phillips Drive Screws.

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Note: There should be a left hand and right hand sidescreen when complete.

2. Position the Rear Screen assembly to the rear of theworksurface, on center.

Note: The Fixed Mount Bracket must not interfere withany part of the table understructure. This may requirethe understructure to be re positioned.

3. Once the screen is in the desired position, attach the Fixed Mount Bracket to the underside of theworksurface using the screws provided.

Note: Use the correct length screw depending on the worksurface thickness: #10 x 1” or #8 x ¾”

F I G U R E 6 . 0

F I G U R E 6 . 1

F I G U R E 6 . 2

6 ) A S S E M B L Y : A C O U S T I C F I X E D S C R E E N

6x

2x

16

I N S T A L L A T I O N G U I D E

4. Position the Side Screen assembly with the RearScreen edges.

Note: The Fixed Mount Bracket must not interfere withany part of the table understructure. This may require the understructure to be re positioned.

5. Once the screen is in the desired position, attach theFixed Mount Bracket to the underside of theworksurface using the screws provided.

Note: Use the correct length screw depending on theworksurface thickness: #10 x 1” or #8 x ¾”.

6. Align the Inner Corner Bracket over the marked hole locations of the Acoustic Screens and attach using the provided #12 x ½”. Pan Head Phillips Drive Screws.

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Tip: These brackets should be installed in the top & bottom corners.

F I G U R E 6 . 3

F I G U R E 6 . 4

F I G U R E 6 . 5

6 ) A S S E M B L Y : A C O U S T I C F I X E D S C R E E N

4x

4x

17

I N S T A L L A T I O N G U I D E

7. Enjoy!

F I G U R E 6 . 6

6 ) A S S E M B L Y : A C O U S T I C F I X E D S C R E E N

18

I N S T A L L A T I O N G U I D E

1. Align the Clamp Bracket over the marked hole locations of the Acoustic Screens and attach using the provided #12 x ½” Pan Head Phillips Drive Screws.

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill to slowest speed and torque setting.

Note: There should be a left hand and right hand side screen when complete.

2. Screw the provided Knobs onto the Clamp Brackets.

3. Loosely attach the Rear Screen assembly to the rear of the worksurface , centering as best as

Note: The Clamp Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

F I G U R E 7 . 0

F I G U R E 7 . 1

F I G U R E 7 . 2

7 ) A S S E M B L Y : A C O U S T I C W I T H R O O F R E M O V A B L E S C R E E N

6x

6x

19

I N S T A L L A T I O N G U I D E

4. Loosely attach the Side Screen assembly, lining up the Rear Screen edges and pushing the Roof tab through the Side Screen slot.

Note: The Clamp Bracket must not interfere with any part of the table understructure. This may require the understructure to be re positioned.

5. Align the Inner Corner Bracket over the marked hole locations of the Acoustic Screens and attach using the provided #12 x ½”. Pan Head Phillips Drive Screws

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill to slowest speed and torque setting.

6. Once the screen is in the desired position, turn the knob until it touches the underside of the worksurface, snuggly.

Note: Once the knob touches the worksurface, only 1 full turn is needed. DO NOT OVER TIGHTEN.

F I G U R E 7 . 3

F I G U R E 7 . 4

F I G U R E 7 . 5

7 ) A S S E M B L Y : A C O U S T I C W I T H R O O F R E M O V A B L E S C R E E N

4x

6x

20

I N S T A L L A T I O N G U I D E

7. Enjoy!

F I G U R E 7 . 6

7 ) A S S E M B L Y : A C O U S T I C W I T H R O O F R E M O V A B L E S C R E E N

21

I N S T A L L A T I O N G U I D E

1. Align the Clamp Bracket over the marked holelocations of the Acoustic Screen and attach using theprovided #12 x ½” Pan Head Phillips Drive Screws.

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Note: There should be a left hand and right hand sidescreen when complete.

2. Position the Rear Screen assembly to the rear of theworksurface, on center.

Note: The Fixed Mount Bracket must not interfere withany part of the table understructure. This may requirethe understructure to be re positioned.

3. Once the screen is in the desired position, attach the Fixed Mount Bracket to the underside of theworksurface using the screws provided.

Note: Use the correct length screw depending on the worksurface thickness: #10 x 1” or #8 x ¾”.

F I G U R E 8 . 0

F I G U R E 8 . 1

F I G U R E 8 . 2

8 ) A S S E M B L Y : A C O U S T I C W I T H R O O F F I X E D S C R E E N

2x

6x

22

I N S T A L L A T I O N G U I D E

4. Position the Side Screen assembly with the RearScreen edges and push the Roof tab through the SideScreen slot.

Note: The Fixed Mount Bracket must not interfere withany part of the table understructure. This may requirethe understructure to be re positioned.

5. Once the screen is in the desired position, attach theFixed Mount Bracket to the underside of theworksurface using the screws provided.

Note: Use the correct length screw depending on theworksurface thickness: #10 x 1” or #8 x ¾”

6. Align the Inner Corner Bracket over the marked hole locations of the Acoustic Screens and attach using the provided #12 x ½”. Pan Head Phillips Drive Screws

Note: DO NOT OVERTIGHTEN SCREWS. Set Drill toslowest speed and torque setting.

Tip: These brackets should be installed in the top & bottom corners.

F I G U R E 8 . 3

F I G U R E 8 . 4

F I G U R E 8 . 5

8 ) A S S E M B L Y : A C O U S T I C W I T H R O O F F I X E D S C R E E N

4x

4x

23

I N S T A L L A T I O N G U I D E

7. Enjoy!

F I G U R E 8 . 6

8 ) A S S E M B L Y : A C O U S T I C W I T H R O O F F I X E D S C R E E N

Specifications subject to change without notice.

Rev 06.2020

1.800.815.7251 www.enwork.com

12900 Christopher Dr. Lowell, MI 49331