electric cylinders dnce, with spindle drive - festo · electric cylinders dnce, with spindle drive...
Post on 18-Apr-2018
227 Views
Preview:
TRANSCRIPT
Electric cylinders DNCE, with spindle drive
Subject to change – 2016/032 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveKey features
At a glance
General Properties Range of applications
The electric cylinder DNCE is a mech
anical linear axis with piston rod. The
drive component consists of an elec
trically driven spindle, which converts
the rotary motion of the motor into the
linear motion of the piston rod.
The mechanical interfaces are largely
compatible with the standard cylinder
DNC.
� Choice of spindle type:
– With lead screw (LS)
– With ball screw (BS)
� Electric cylinder with lead screw
spindle is self-retarding
� Compact dimensions
Optional:
� Protection class IP65
� High corrosion protection
� NSF-H1 lubricant for the food
industry
� Lead screw spindle
– For applications with slow feed
speeds
� Ball screw spindle
– For applications with high feed
speeds and high running
performance
-H- Note
The electric cylinder is of limited
suitability for the food industry.
Further information www.festo.com/
sp � User documentation.
Entire system consisting of electric cylinder, motor and motor mounting kit
Electric cylinder � 6
3
4
3
4
1
2
-H- Note
The lead screw spindle is self-retard
ing, which means that slow move
ments cannot be excluded in the
event of vibration.
The entire system with intelligent
motor unit MTR-DCI is self-locking.
1 Parallel kit
2 Axial kit
3 Slot for proximity sensor
4 Choice of spindle type:
– With lead screw spindle (LS)
– With ball screw spindle (BS)
Motor/motor unit � 18
1 2 3
1 Motor unit MTR-DCI
2 Servo motor EMME-AS, EMMS-AS
3 Stepper motor EMMS-ST
-H- Note
A range of specially adapted
complete solutions is available for
the electric cylinder DNCE and the
motors/motor units.
Motor mounting kit � 18
Axial kit Parallel kit
A range of complete kits is available
for both parallel and axial motor
mounting.
2016/03 – Subject to change 3� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveKey features and type codes
Longer service life with bellows kit EADB � 27
1
The protective bellows kit is a leak-
free system. To prevent unwanted me
dia from being drawn in, the supply
and exhaust air must be ducted via a
pressure compensation hole in the
connection part 1.
The kit protects the piston rod, seal
and bearings against a wide variety of
media, for example:
� Dust
� Chippings
� Oil
� Grease
� Fuel
Use in dusty or wet environments thanks to protection to IP65 (feature P5) � 17
1
The electric cylinder to IP65 fulfils the
specifications to IEC 60 529.
Air is exchanged between the interior
of the cylinder and the environment
via a pressure compensation hole 1
in the cylinder barrel. This prevents
negative pressure or excess pressure
in the interior of the cylinder.
It also prevents unwanted media
being drawn in.
Protection to IP65 can only be selec
ted in combination with DNCE-…-BS
(ball screw spindle).
Type codes
DNCE — 32 — 100 — BS — ”10”P — Q-P5
Type
DNCE Electric cylinder
Size
Stroke [mm]
Drive function
LS Lead screw spindle
BS Ball screw spindle
Spindle pitch [mm]
Variant
Q Non-rotating piston rod
K8 Extended piston rod
K3 Female piston rod thread
P5 Protection class IP65
R3 High corrosion protection
FG Lubrication approved for use in food
applications
Subject to change – 2016/034 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle drivePeripherals overview
1
2
3
4
6
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
2
3
4
bB
bD
bE
5
1
4
9
bC
bF
bG
bH
bI
cJ
Mounting attachments and accessories
Description � Page/Internet
1 Foot mounting
HNC/CRHNC
For mounting the cylinder 32
2 Flange mounting
FNC/CRFNG
– Cannot be used on the bearing cap in combination with bellows kit EADB 33
3 Trunnion flange
ZNCF/CRZNG
– Cannot be used on the bearing cap in combination with bellows kit EADB 34
2016/03 – Subject to change 5� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle drivePeripherals overview
Mounting attachments and accessories
Description � Page/Internet
4 Trunnion support
LNZG/CRLNZG
For cylinders with trunnion mounting 35
5 Swivel flange
SNC
With parallel motor mounting 36
6 Clevis foot
LSNG
With parallel motor mounting, with spherical bearing 40
7 Clevis foot
LSNSG
With parallel motor mounting, weld-on, with spherical bearing 40
8 Swivel flange
SNCS
With parallel motor mounting, with spherical bearing 37
9 Clevis foot
LBG
With parallel motor mounting, with spherical bearing 40
aJ Swivel flange
SNCL
With parallel motor mounting 38
aA Swivel flange
SNCB/SNCB-…-R3
With parallel motor mounting, with spherical bearing 39
aB Swivel flange
SNCB/SNCB-…-R3
With parallel motor mounting 39
aC Clevis foot
LNG/CRLNG
With parallel motor mounting 40
aD Clevis foot
LSN
With parallel motor mounting, with spherical bearing 40
aE Trunnion mounting kit
DAMT
For mounting anywhere along the cylinder profile barrel. Cannot be mounted in the vicinity of the
motor with parallel motor mounting
40
aF Foot mounting
HNCE
– With axial motor mounting
– Cannot be used in combination with the axial kit EAMM-A-…-S1 (protection class IP65)
30
aG Rod eye
SGS/CRSGS
With spherical bearing 41
aH Coupling piece
KSZ
To compensate for radial deviations 41
aI Rod clevis
SG/CRSG
Permits a swivelling movement of the cylinder in one plane 41
bJ Self-aligning rod coupler
FK/CRFK
For compensating radial and angular deviations 41
bA Right-angle clevis foot
LQG
For rod eye SGS 41
bB Rod clevis
SGA
For swivel mounting of cylinders 41
bC Guide unit
FENG
– For protecting electric cylinders against rotation at high torque loads
– Cannot be used in combination with bellows kit EADB
41
bD Proximity sensor
SME/SMT-8
For position sensing. Can be integrated in the sensor slot, thus avoiding projecting parts 42
bE Slot cover
ABP-5-S
For protecting against the ingress of dirt 42
bF Parallel kit
EAMM-U
For parallel motor mounting 18
bG Axial kit
EAMM-A
For axial motor mounting 18
bH Profile mounting
EAHF
– For mounting the electric cylinder via the profile
– Cannot be mounted in the vicinity of the motor in combination with the parallel kit EAMM-U
31
bI Compensating element
EADC
Compensates the play between the piston rod of the electric cylinder DNCE and the yoke plate of the
guide unit FENG
42
cJ Bellows kit
EADB
– Protects the cylinder (piston rod, seal and bearings) against a wide range of media and thus
prevents premature wear
– The kit can only be used in combination with an extended piston rod (K8)
27
Subject to change – 2016/036 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Function -N- Size
32 … 63
-T- Stroke length
1 … 800 mm
-W- www.festo.com
With axial kit With parallel kit
General technical data
Size 32 40 63
Design With lead screw spindle (LS)
With ball screw spindle (BS)
Piston rod thread
Male thread M10x1.25 M12x1.25 M16x1.5
Female thread M6 M8 M10
Working stroke [mm] 1 … 400 1 … 600 1 … 800
Variant Non-rotating piston rod
Protection against rotation/guide Plain-bearing guide
Stroke reserve [mm] 0
Max. torsion angle
of the piston rod
[°] 0.30 0.25 0.20
Impact energy (E)
in the end positions
[J] 0.0001 E� � 0.5 � m � v2 0.0002 E� � 0.5 � m � v2 0.0004 E� � 0.5 � m � v2
Duty cycle1) [%] 100
Position sensing Via proximity sensor
Type of mounting Via female thread
Via accessories
Mounting position Any
1) In the case of the variant with lead screw spindle (LS), the duty cycle depends on the speed
Mechanical data
Size 32 40 63
Spindle design LS-”1,5”P BS-”3”P BS-”10”P LS-”2,5”P BS-”5”P BS-”12,7”P LS-”4”P BS-”10”P BS-”20”P
Spindle pitch [mm/
rev.]
1.5 3 10 2.5 5 12.7 4 10 20
Spindle diameter [mm] 9 10 10 12.5 12 12.7 20 20 20
Max. stat. axial force [N] 600 600 600 1400 1400 1400 3700 3700 3700
Max. feed force Fx1) [N] 300 300 350 600 525 800 1000 2500 1625
Continuous feed force1) [N] 300 240 280 600 420 640 1000 2000 1300
Max. driving torque2) [Nm] 0.4 0.4 0.8 1.15 0.9 1.9 3 4.9 5.9
Max. radial force3) [N] 120 120 120 260 260 260 300 300 300
Max. speed [m/s] 0.06 0.15 0.5 0.07 0.25 0.64 0.07 0.5 1.0
Max. rotational speed [rpm] 2400 3000 3000 1650 3000 3000 1050 3000 3000
Max. acceleration [m/s2] 1 6 6 1 6 6 1 6 6
Reversing backlash4) [mm] 0.2 0.05 0.05 0.2 0.05 0.05 0.2 0.05 0.05
Repetition accuracy [mm] 0.07 0.02 0.02 0.07 0.02 0.02 0.07 0.02 0.02
1) In the case of the variant with lead screw spindle (LS), the feed force depends on the speed � 10
The feed force in the case of the variant with ball screw spindle (BS) � 8
2) In the case of the variant with lead screw spindle (LS), the driving torque depends on the rotational speed � 11
3) At the drive shaft
4) In new condition
2016/03 – Subject to change 7� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Mechanical data
Size 32 40 63
Spindle design LS-”1,5”P BS-”3”P BS-”10”P LS-”2,5”P BS-”5”P BS-”12,7”P LS-”4”P BS-”10”P BS-”20”P
No-load driving torque
With axial kit1)
DNCE-… [Nm] 0.08 0.08 0.08 0.12 0.12 0.12 0.3 0.2 0.2
DNCE-…-P5 [Nm] – 0.12 0.12 – 0.18 0.18 – 0.3 0.3
With parallel kit1)
DNCE-… [Nm] 0.13 0.13 0.13 0.22 0.22 0.22 0.6 0.5 0.5
DNCE-…-P5 [Nm] – 0.17 0.17 0.17 0.28 0.28 – 0.6 0.6
Continuous driving torque [Nm] 0.4 0.3 0.6 1.15 0.8 1.6 3 4.1 4.8
1) Measured at a speed of 200 rpm
Operating and environmental conditions
Ambient temperature1) [°C] 0 … 50
Storage temperature [°C] –25 … +60
Protection class to IEC 60529
DNCE-… IP40
DNCE-…-P5 IP65
Relative air humidity [%] 0 … 95
Food-safe2) See supplementary material information
Corrosion resistance class CRC3)
DNCE-…-R3 3
1) Note operating range of proximity sensors and motors
2) Additional information www.festo.com/sp � Certificates.
3) Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
Weight [g]
Size 32 40 63
Spindle design LS-”1,5”P BS-”3”P BS-”10”P LS-”2,5”P BS-”5”P BS-”12,7”P LS-”4”P BS-”10”P BS-”20”P
Basic weight with 0 mm stroke 720 750 770 1210 1270 1350 2790 3010 3010
Additional weight per 10 mm stroke 32.4 33 33.6 46.1 45.5 46.7 79.8 81.2 81.2
Moving load with 0 mm stroke 150 170 200 250 310 380 600 810 810
Moving load per 10 mm stroke 6.9 6.9 6.9 8.9 8.9 8.9 12.8 12.8 12.8
Mass moment of inertia
Size 32 40 63
Spindle design LS-”1,5”P BS-”3”P BS-”10”P LS-”2,5”P BS-”5”P BS-”12,7”P LS-”4”P BS-”10”P BS-”20”P
J0 with 0 mm stroke [kg cm2] 0.0433 0.0439 0.0446 0.1316 0.1304 0.1337 0.7565 0.7626 0.7624
jH per metre stroke [kg cm2/m] 0.0361 0.0476 0.0595 0.1341 0.1163 0.1572 0.8176 0.9090 0.9103
jL per kg working load [kg cm2/kg] 0.0006 0,0023 0.0253 0.0016 0.0063 0.0409 0.0041 0.0253 0.1013
The mass moment of inertia JA of the
electric cylinder is calculated as
follows:
JA = J0 + jH x working stroke [m] + jL x mworking load [kg]
Subject to change – 2016/038 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Calculation of the mean feed force Fxm for the electric cylinder DNCE with ball screw spindle (BS)
The peak feed force value must not ex
ceed the maximum feed force within a
movement cycle. In the case of vertical
operation, the peak value is generally
achieved during the acceleration
phase of the upwards stroke. If the
maximum feed force is exceeded, this
can increase wear and thus shorten
the service life of the ball screw
spindle. The maximum speed must
likewise not be exceeded.
Fx �� Fxmax.
vx �� vxmax.
and
Mean feed force (to DIN 69 051-4)
During operation, the continuous feed
force may be briefly exceeded up to
the maximum feed force. The
continuous feed force must, however,
be adhered to when averaged over a
movement cycle.
Fxm �� Fxcont
Fxm ��3 � Fx3 �
vxvxm
�q
100� �� �
Fxm ��3 Fx13 �
vx1vxm
�q1
100� Fx2
3 �vx2vxm
�q2
100� Fx3
3 �vx3vxm
�q3
100� ���� F x
[N]
q1 q2 q3q [100%]
Fx1
Fx2
Fx3
Fxmax
Fxm
Mean feed speed (to DIN 69 051-4)
vxm ��� vx �q
100� vx1 �
q1
100� vx2 �
q2
100� vx3 �
q3
100� ���
q [100%]q1 q2 q3
v x [m
m/s
]
vx1
vx3
vx2vxmax
vxm
Fx Feed force
Fxm Mean feed force
Fxmax. Max. feed force
Fxcont Continuous feed force
q Time
vx Feed speed
vxm Mean feed speed
vxmax. Max. feed speed
Materials
Sectional view
1 4 52 3 6
Electric cylinder
1 Bearing cap Painted die-cast aluminium
2 Cylinder barrel Smooth anodised wrought aluminium alloy
3 Piston rod High-alloy stainless steel
4 Spindle Steel
5 Spindle nut for LS Polyacetal
Spindle nut for BS Steel
6 Drive cover Painted die-cast aluminium
– Note on materials RoHS-compliant
Contains PWIS (paint-wetting impairment substances)
2016/03 – Subject to change 9� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Maximum permissible loads on the piston rod
If there are two or more forces and
torques simultaneously acting on
the piston rod, the following
equations must be satisfied:
|Fy|
Fymax.�
|Fz|
Fzmax.�
|My|
Mymax.�
|Mz|
Mzmax.� 1
|Fx| � Fxmax
|Mx| � Mxmax
Definition of the stroke length l:
l = Stroke + value of the piston rod
extension K8
Maximum permissible lateral forces Fymax and Fzmax on the piston rod as a function of stroke length l
Horizontal mounting position Vertical mounting position
DNCE-32-LS/BS
DNCE-40-LS/BS
DNCE-63-LS/BS
Size 32 40 63
Maximum permissible forces and torques
Fxmax (static) [N] 600 1400 3700
Mxmax [Nm] 1 1 1.5
Mymax, Mzmax [Nm] 8 20 27
-H- Note
PositioningDrives
sizing software
� www.festo.com
Subject to change – 2016/0310 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Feed force F as a function of speed v
DNCE-32-1…299-LS-… DNCE-32-300…400-LS-…
DNCE-40-1…299-LS-… DNCE-40-300…600-LS-…
DNCE-63-1…419-LS-… DNCE-63-420…800-LS-…
Recommended operating range
Permissible operating range
(duty cycle 50% recommended)
2016/03 – Subject to change 11� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Driving torque M as a function of rotational speed n
DNCE-32-1…299-LS-… DNCE-32-300…400-LS-…
DNCE-40-1…299-LS-… DNCE-40-300…600-LS-…
DNCE-63-1…419-LS-… DNCE-63-420…800-LS-…
Recommended operating range
Permissible operating range
(duty cycle 50% recommended)
Subject to change – 2016/0312 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Rotational speed n as a function of speed v
DNCE-…-LS-… DNCE-…-BS-…
DNCE-32-LS-”1,5”P
DNCE-40-LS-”2,5”P
DNCE-63-LS-”4”P
DNCE-32-BS-”3”P
DNCE-40-BS-”5”P
DNCE-63-BS-”10”P
DNCE-32-BS-”10”P
DNCE-40-BS-”12,7”P
DNCE-63-BS-”20”P
Driving torque M as a function of feed force F
-H- Note
The frictional torques at room
temperature are taken into
consideration in the graphs.
The frictional torques with the
DNCE-…-LS (lead screw spindle)
increase at lower temperatures.
PositioningDrives
sizing software
� www.festo.com
DNCE-…-LS-…
DNCE-32-LS-”1,5”P
DNCE-40-LS-”2,5”P
DNCE-63-LS-”4”P
DNCE-…-BS-…
DNCE-32-BS-”3”P
DNCE-40-BS-”5”P
DNCE-63-BS-”10”P
DNCE-32-BS-”10”P
DNCE-40-BS-”12,7”P
DNCE-63-BS-”20”P
2016/03 – Subject to change 13� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Piston rod displacement f as a function of stroke length l
Definition of the stroke length l:
l = Stroke + value of the piston rod
extension K8
DNCE-32-… DNCE-40-…
Lateral force F = 0 N
Lateral force F = 10 N
Lateral force F = 20 N
Lateral force F = 45 N
Lateral force F = 0 N
Lateral force F = 20 N
Lateral force F = 30 N
Lateral force F = 40 N
Lateral force F = 115 N
DNCE-63-…
Lateral force = 0 N
Lateral force = 20 N
Lateral force = 30 N
Lateral force = 40 N
Lateral force = 95 N
Subject to change – 2016/0314 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Mean feed force F as a function of running performance L (to DIN 69 051-4)
DNCE-32-…-BS-… DNCE-40-…-BS-…
DNCE-32-BS-”3”P
DNCE-32-BS-”10”P
DNCE-40-BS-”5”P
DNCE-40-BS-”12,7”P
DNCE-63-…-BS-…
DNCE-63-BS-”10”P
DNCE-63-BS-”20”P
-H- Note
� The specifications for running
performance are based on
experimentally determined and
theoretically calculated data. The
running performance attainable in
practice can deviate considerably
from the specified curves under
different parameters.
2016/03 – Subject to change 15� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Dimensions Download CAD data � www.festo.com
Basic version
+ = plus stroke length
Size
[mm]
AM B
d11
B1 B2 BG D1
h9
D2
h6
D3
f7
D4 E G G1 H1 H2 KK
32 22 30 19 32 16 16 6 32 M3 45.5 24 26 19 32 M10x1.25
40 24 35 20 42 16 20 8 40 M4 54 28.5 30 20 42 M12x1.25
63 32 45 31 62 17 28 12 60 M5 75.5 34 36 31 62 M16x1.5
Size
[mm]
L1 L2 L3 L4 L5 MM MP RT TG VA VD
+1/–0.7
WH ZJ
±1
ß1 ß2 ß3
32 18 122 15.9 8 3.5 12 M3 M6 32.5 7 10 26 148 10 17 6
40 21.5 146.5 18.4 14 3.5 16 M3 M6 38 7 10.5 30 176.5 13 19 6
63 28.5 177 23.5 17 4.5 20 M4 M8 56.5 9 15 37 214 17 24 8
Variants
K8 – Extended piston rod K3 – Female piston rod thread
P5 – Protection class IP65
Size
[mm]
A2
max.
AF EE KF L6 T5 D5 WH
32 200 12 Gx M6 37.6 2.6 6.4 26
40 200 12 G¼ M8 45.6 3.3 8.4 30
63 200 16 G¼ M10 57.6 4.7 10.5 37
Subject to change – 2016/0316 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveTechnical data
Ordering data – DNCE-32
Stroke
[mm]
Part No. Type Stroke
[mm]
Part No. Type
Ball screw spindle with spindle pitch 3 mm Lead screw spindle with spindle pitch 1.5 mm
100 543115 DNCE-32-100-BS-”3”P-Q 100 543111 DNCE-32-100-LS-”1,5”P-Q
200 543116 DNCE-32-200-BS-”3”P-Q 200 543112 DNCE-32-200-LS-”1,5”P-Q
300 543117 DNCE-32-300-BS-”3”P-Q 300 543113 DNCE-32-300-LS-”1,5”P-Q
400 543118 DNCE-32-400-BS-”3”P-Q 400 543114 DNCE-32-400-LS-”1,5”P-Q
Ball screw spindle with spindle pitch 10 mm
100 543119 DNCE-32-100-BS-”10”P-Q
200 543120 DNCE-32-200-BS-”10”P-Q
300 543121 DNCE-32-300-BS-”10”P-Q
400 543122 DNCE-32-400-BS-”10”P-Q
Ordering data – DNCE-40
Stroke
[mm]
Part No. Type Stroke
[mm]
Part No. Type
Ball screw spindle with spindle pitch 5 mm Lead screw spindle with spindle pitch 2.5 mm
100 543127 DNCE-40-100-BS-”5”P-Q 100 543123 DNCE-40-100-LS-”2,5”P-Q
200 543128 DNCE-40-200-BS-”5”P-Q 200 543124 DNCE-40-200-LS-”2,5”P-Q
300 555466 DNCE-40-300-BS-”5”P-Q 300 555465 DNCE-40-300-LS-”2,5”P-Q
400 543129 DNCE-40-400-BS-”5”P-Q 400 543125 DNCE-40-400-LS-”2,5”P-Q
600 543130 DNCE-40-600-BS-”5”P-Q 600 543126 DNCE-40-600-LS-”2,5”P-Q
Ball screw spindle with spindle pitch 12.7 mm
100 543131 DNCE-40-100-BS-”12,7”P-Q
200 543132 DNCE-40-200-BS-”12,7”P-Q
300 555467 DNCE-40-300-BS-”12,7”P-Q
400 543133 DNCE-40-400-BS-”12,7”P-Q
600 543134 DNCE-40-600-BS-”12,7”P-Q
Ordering data – DNCE-63
Stroke
[mm]
Part No. Type Stroke
[mm]
Part No. Type
Ball screw spindle with spindle pitch 10 mm Lead screw spindle with spindle pitch 4 mm
100 555470 DNCE-63-100-BS-”10”P-Q 100 555468 DNCE-63-100-LS-”4”P-Q
200 543139 DNCE-63-200-BS-”10”P-Q 200 543135 DNCE-63-200-LS-”4”P-Q
300 555471 DNCE-63-300-BS-”10”P-Q 300 555469 DNCE-63-300-LS-”4”P-Q
400 543140 DNCE-63-400-BS-”10”P-Q 400 543136 DNCE-63-400-LS-”4”P-Q
600 543141 DNCE-63-600-BS-”10”P-Q 600 543137 DNCE-63-600-LS-”4”P-Q
800 543142 DNCE-63-800-BS-”10”P-Q 800 543138 DNCE-63-800-LS-”4”P-Q
Ball screw spindle with spindle pitch 20 mm
100 555472 DNCE-63-100-BS-”20”P-Q
200 543143 DNCE-63-200-BS-”20”P-Q
300 555473 DNCE-63-300-BS-”20”P-Q
400 543144 DNCE-63-400-BS-”20”P-Q
600 543145 DNCE-63-600-BS-”20”P-Q
800 543146 DNCE-63-800-BS-”20”P-Q
-H- Note
Order variable strokes via the
modular product system � 17
2016/03 – Subject to change 17� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveOrdering data – Modular products
Ordering table
Size 32 40 63 Condi
tions
Code Enter
code
0M Module No. 555488 555489 555490
Function Electric cylinder DNCE DNCE
Size 32 40 63 -…
Stroke [mm] 100 -…
200
300
400
– 600
– – 800
1 … 400 1 … 600 1 … 800 1
Drive type Lead screw spindle -LS
Ball screw spindle -BS
Spindle pitch [mm] 1.5 – – 2 -“…”P
– 2.5 – 2
3 – – 3
– – 4 2
– 5 – 3
10 – 10 3
– 12.7 – 3
– – 20 3
Protection against rotation Non-rotating piston rod -Q -Q
0O Extended piston rod 1 … 200 3 -…K8
Female thread M6 M8 M10 3 -K3
Protection class to IEC 60529 IP65 3 -P5
Corrosion protection High corrosion protection 3 4 -R3
Lubrication Lubrication approved for use in food applications 3 5 -FG
1 … Additional stroke lengths on request
2 “1.5“P, “2.5“P, “4“P
Only with drive type LS
3 “3“P, “5“P, “10“P, “12.7“P, “20“P, …K8, K3, P5
Only with ball screw spindle BS
4 R3 Only with P5
5 FG Only with R3 and P5
Transfer order code
DNCE – – – – – Q – – –
Subject to change – 2016/0318 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
-H- Note
Depending on the combination of
motor and drive, it may not be
possible to reach the maximum feed
force of the drive.
When using parallel kits, the no-load
driving torque of the respective kit
must be taking into consideration.
The following tool is available for
sizing:
PositioningDrives
engineering software
� www.festo.com
Permissible axis/motor combinations with axial kit Technical data � Internet: eamm-a
Motor/gear unit1) Axial kit
Type Part No. Type
DNCE-32
With servo motor
EMME-AS-40-… 1976465 EAMM-A-D32-40P
2207372 EAMM-A-D32-40P-S12)
EMMS-AS-40-… 543147 EAMM-A-D32-40A
1322178 EAMM-A-D32-40A-S12)
EMMS-AS-55-… 550979 EAMM-A-D32-55A
1322180 EAMM-A-D32-55A-S12)
EMME-AS-60-… 1956054 EAMM-A-D32-60P
2234020 EAMM-A-D32-60P-S12)
With servo motor and gear unit
EMME-AS-40-…
EMGA-40-P-G…-EAS-40
1454238 EAMM-A-D32-40G
2256396 EAMM-A-D32-40G-S12)
EMMS-AS-40-…
EMGA-40-P-G…-SAS-40
1454238 EAMM-A-D32-40G
2256396 EAMM-A-D32-40G-S12)
EMMS-AS-55-…
EMGA-60-P-G…-SAS-55
2946758 EAMM-A-D32-60G
2946759 EAMM-A-D32-60G-S12)
EMME-AS-60-…
EMGA-60-P-G…-EAS-60
2946760 EAMM-A-D32-60H
2946761 EAMM-A-D32-60H-S12)
EMMS-AS-70-…
EMGA-60-P-G…-SAS-70
2946758 EAMM-A-D32-60G
2946759 EAMM-A-D32-60G-S12)
With stepper motor
EMMS-ST-42-… 543148 EAMM-A-D32-42A
1322179 EAMM-A-D32-42A-S12)
EMMS-ST-57-… 550980 EAMM-A-D32-57A
1322181 EAMM-A-D32-57A-S12)
With stepper motor and gear unit
EMMS-ST-42-…
EMGA-40-P-G…-SST-42
1454238 EAMM-A-D32-40G
2256396 EAMM-A-D32-40G-S12)
EMMS-ST-57-…
EMGA-60-P-G…-SST-57
2946758 EAMM-A-D32-60G
2946759 EAMM-A-D32-60G-S12)
With integrated drive
EMCA-EC-67-… 1454239 EAMM-A-D32-67A
2256397 EAMM-A-D32-67A-S12)
With motor unit
MTR-DCI-32S-…3) 543149 EAMM-A-D32-32B
With integrated drive and gear unit
EMCA-EC-67-…
EMGC-40-…
1454238 EAMM-A-D32-40G
2256396 EAMM-A-D32-40G-S12)
EMCA-EC-67-…
EMGC-60-…
2946760 EAMM-A-D32-60H
2946761 EAMM-A-D32-60H-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the axial kit.
2) With degree of protection IP65.
3) Only in combination with DNCE-…-LS.
2016/03 – Subject to change 19� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Permissible axis/motor combinations with axial kit Technical data � Internet: eamm-a
Motor/gear unit1) Axial kit
Type Part No. Type
DNCE-40
With servo motor
EMMS-AS-55-… 543153 EAMM-A-D40-55A
1322182 EAMM-A-D40-55A-S12)
EMME-AS-60-… 1977000 EAMM-A-D40-60P
2151519 EAMM-A-D40-60P-S12)
EMMS-AS-70-… 550981 EAMM-A-D40-70A
1322185 EAMM-A-D40-70A-S12)
With servo motor and gear unit
EMME-AS-40-…
EMGA-40-P-G…-EAS-40
560282 EAMM-A-D40-40G3)
2256398 EAMM-A-D40-40G-G2
2256399 EAMM-A-D40-40G-S12)
EMMS-AS-40-…
EMGA-40-P-G…-SAS-40
560282 EAMM-A-D40-40G3)
2256398 EAMM-A-D40-40G-G2
2256399 EAMM-A-D40-40G-S12)
EMMS-AS-55-…
EMGA-60-P-G…-SAS-55
2256400 EAMM-A-D40-60G
2256409 EAMM-A-D40-60G-S12)
EMME-AS-60-…
EMGA-60-P-G…-EAS-60
1454242 EAMM-A-D40-60H
2256401 EAMM-A-D40-60H-S12)
EMMS-AS-70-…
EMGA-60-P-G…-SAS-70
2256400 EAMM-A-D40-60G
2256409 EAMM-A-D40-60G-S12)
With stepper motor
EMMS-ST-57-… 543154 EAMM-A-D40-57A
1322183 EAMM-A-D40-57A-S12)
EMMS-ST-87-… 550982 EAMM-A-D40-87A
1322186 EAMM-A-D40-87A-S12)
With stepper motor and gear unit
EMMS-ST-42-…
EMGA-40-P-G…-SST-42
560282 EAMM-A-D40-40G3)
2256398 EAMM-A-D40-40G-G2
2256399 EAMM-A-D40-40G-S12)
EMMS-ST-57-…
EMGA-60-P-G…-SST-57
2256400 EAMM-A-D40-60G
2256409 EAMM-A-D40-60G-S12)
With integrated drive
EMCA-EC-67-… 1454243 EAMM-A-D40-67A
2256695 EAMM-A-D40-67A-S12)
With motor unit
MTR-DCI-42S-…-G74) 543155 EAMM-A-D40-42B
MTR-DCI-42S-…-G144) 543156 EAMM-A-D40-42C
With integrated drive and gear unit
EMCA-EC-67-…
EMGC-40-…
560282 EAMM-A-D40-40G3)
2256398 EAMM-A-D40-40G-G2
2256399 EAMM-A-D40-40G-S12)
EMCA-EC-67-…
EMGC-60-…
1454242 EAMM-A-D40-60H
2256401 EAMM-A-D40-60H-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the axial kit.
2) With degree of protection IP65.
3) Type discontinued
4) Only in combination with DNCE-…-LS.
Subject to change – 2016/0320 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Permissible axis/motor combinations with axial kit Technical data � Internet: eamm-a
Motor/gear unit1) Axial kit
Type Part No. Type
DNCE-63
With servo motor
EMMS-AS-70-… 543161 EAMM-A-D60-70A
2256699 EAMM-A-D60-70A-S12)
EMME-AS-80-… 1977073 EAMM-A-D60-80P
2218564 EAMM-A-D60-80P-S12)
EMME-AS-100-… 550983 EAMM-A-D60-100A
2256700 EAMM-A-D60-100A-S12)
EMMS-AS-100-… 550983 EAMM-A-D60-100A
2256700 EAMM-A-D60-100A-S12)
With servo motor and gear unit
EMMS-AS-55-…
EMGA-60-P-G…-SAS-55
560283 EAMM-A-D60-60G3)
2256696 EAMM-A-D60-60G-G2
2256698 EAMM-A-D60-60G-S12)
EMME-AS-60-…
EMGA-60-P-G…-EAS-60
1454245 EAMM-A-D60-60H
2256697 EAMM-A-D60-60H-S12)
EMMS-AS-70-…
EMGA-60-P-G…-SAS-70
560283 EAMM-A-D60-60G3)
2256696 EAMM-A-D60-60G-G2
2256698 EAMM-A-D60-60G-S12)
EMMS-AS-70-…
EMGA-80-P-G…-SAS-70
1499402 EAMM-A-D60-80G
2946762 EAMM-A-D60-80G-S12)
EMME-AS-80-…
EMGA-80-P-G…-EAS-80
1499402 EAMM-A-D60-80G
2946762 EAMM-A-D60-80G-S12)
EMMS-AS-100-…
EMGA-80-P-G…-SAS-100
1499402 EAMM-A-D60-80G
2946762 EAMM-A-D60-80G-S12)
With stepper motor
EMMS-ST-87-… 543162 EAMM-A-D60-87A
1322188 EAMM-A-D60-87A-S12)
With stepper motor and gear unit
EMMS-ST-57-…
EMGA-60-P-G…-SST-57
560283 EAMM-A-D60-60G3)
2256696 EAMM-A-D60-60G-G2
2256698 EAMM-A-D60-60G-S12)
EMMS-ST-87-…
EMGA-80-P-G…-SST-87
1499402 EAMM-A-D60-80G
2946762 EAMM-A-D60-80G-S12)
With motor unit3)
MTR-DCI-52S-…-G74) 543163 EAMM-A-D60-52B
MTR-DCI-52S-…-G144) 543164 EAMM-A-D60-52C
With integrated drive and gear unit
EMCA-EC-67-…
EMGC-60-…
1454245 EAMM-A-D60-60H
2256697 EAMM-A-D60-60H-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the axial kit.
2) With degree of protection IP65.
3) Type discontinued.
4) Only in combination with DNCE-…-LS.
-H- Note
The axial kit (without “S1” in the
type code) can be retrofitted with a
seal set EADS-F to change the
degree of protection from IP40 to
IP65.
More information
� eamm-u
2016/03 – Subject to change 21� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Component parts of the axial kit
Axial kit Comprising:
Motor flange Coupling Coupling housing Seal set
Part No. Part No.. Part No. Part No. Part No.
Type Type Type Type Type
DNCE-32
543149
EAMM-A-D32-32B2)
– 543420
EAMC-16-20-6-6
552156
EAMK-A-D32-32B
–
543147
EAMM-A-D32-40A
552163
EAMF-A-28B-40A
543420
EAMC-16-20-6-6
552155
EAMK-A-D32-28B
–
1322178
EAMM-A-D32-40A-S1)
1561526
EADS-F-D32-40A
1454238
EAMM-A-D32-40G
1460095
EAMF-A-44C-40G-S1
562681
EAMC-30-32-6-10
551006
EAMK-A-D32-44A/C
–
2256396
EAMM-A-D32-40G-S11)
2253500
EADS-F-D32-40G
1976465
EAMM-A-D32-40P
1976704
EAMF-A-28B-40P
1232854
EAMC-16-20-6-8
552155
EAMK-A-D32-28B
–
2207372
EAMM-A-D32-40P-S11)
2207219
EADS-F-D32-40P
543148
EAMM-A-D32-42A
552164
EAMF-A-28B-42A
543419
EAMC-16-20-5-6
552155
EAMK-A-D32-28B
–
1322179
EAMM-A-D32-42A-S11)
1561527
EADS-F-D32-42A
550979
EAMM-A-D32-55A
529942
EAMF-A-44A/B-55A
551003
EAMC-30-32-6-9
551006
EAMK-A-D32-44A/C
–
1322180
EAMM-A-D32-55A-S11)
1561528
EADS-F-D32-55A
550980
EAMM-A-D32-57A
530081
EAMF-A-44A/B-57A
551002
EAMC-30-32-6-6.35
551006
EAMK-A-D32-44A/C
–
1322181
EAMM-A-D32-57A-S11)
1561529
EADS-F-D32-57A
2946758
EAMM-A-D32-60G
1460105
EAMF-A-44C-60G/H-S1
318577
EAMC-30-32-6-11
551006
EAMK-A-D32-44A/C
–
2946759
EAMM-A-D32-60G-S11)
8022150
EADS-F-D32-60G/H
2946760
EAMM-A-D32-60H
1460105
EAMF-A-44C-60G/H-S1
1233256
EAMC-30-32-6-14
551006
EAMK-A-D32-44A/C
–
2946761
EAMM-A-D32-60H-S11)
8022150
EADS-F-D32-60G/H
1956054
EAMM-A-D32-60P
1956846
EAMF-A-44C-60P
1233256
EAMC-30-32-6-14
551006
EAMK-A-D32-44A/C
–
2234020
EAMM-A-D32-60P-S11)
2234012
EADS-F-D32-60P
1454239
EAMM-A-D32-67A
1476305
EAMF-A-44A/B/C-67A-S1
551003
EAMC-30-32-6-9
551006
EAMK-A-D32-44A/C
–
2256397
EAMM-A-D32-67A-S11)
2253501
EADS-F-D32-67A
1) With degree of protection IP65.
2) Only with DNCE-…-LS.
Subject to change – 2016/0322 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Part components of the axial kit
Axial kit Comprising:
Motor flange Coupling Coupling housing Seal set
Part No. Part No. Part No. Part No. Part No.
Type Type Type Type Type
DNCE-40
543155
EAMM-A-D40-42B3)
– 543422
EAMC-30-32-8-8
552158
EAMK-A-D40-42B
–
543156
EAMM-A-D40-42C3)
– 543422
EAMC-30-32-8-8
552159
EAMK-A-D40-42C
–
560282
EAMM-A-D40-40G2)
550986
EAMF-44A/B-40G
558029
EAMC-30-32-8-10
552157
EAMK-A-D40-44A/C
–
2256398
EAMM-A-D40-40G-G2
1460095
EAMF-A-44C-40G-S1
558029
EAMC-30-32-8-10
552157
EAMK-A-D40-44A/C
–
2256399
EAMM-A-D40-40G-S11)
2253502
EADS-F-D40-40G
543153
EAMM-A-D40-55A
529942
EAMF-A-44A/B-55A
543423
EAMC-30-32-8-9
552157
EAMK-A-D40-44A/C
–
1322182
EAMM-A-D40-55A-S11)
1561530
EADS-F-D40-55A
543154
EAMM-A-D40-57A
530081
EAMF-A-44A/B-57A
543421
EAMC-30-32-6.35-8
552157
EAMK-A-D40-44A/C
–
1322183
EAMM-A-D40-57A-S11)
1561531
EADS-F-D40-57A
2256400
EAMM-A-D40-60G
1460105
EAMF-A-44C-60G/H-S1
551004
EAMC-30-32-8-11
552157
EAMK-A-D40-44A/C
–
2256409
EAMM-A-D40-60G-S11)
2253503
EADS-F-D40-60G/H
1454242
EAMM-A-D40-60H
1460105
EAMF-A-44C-60G/H-S1
562682
EAMC-30-32-8-14
552157
EAMK-A-D40-44A/C
–
2256401
EAMM-A-D40-60H-S11)
2253503
EADS-F-D40-60G/H
1977000
EAMM-A-D40-60P
1956846
EAMF-A-44C-60P
562682
EAMC-30-32-8-14
552157
EAMK-A-D40-44A/C
–
2151519
EAMM-A-D40-60P-S11)
2151545
EADS-F-D40-60P
1454243
EAMM-A-D40-67A
1476305
EAMF-A-44A/B/C-67A-S1
543423
EAMC-30-32-8-9
552157
EAMK-A-D40-44A/C
–
2256695
EAMM-A-D40-67A-S11)
2253504
EADS-F-D40-67A
550981
EAMM-A-D40-70A
529943
EAMF-A-44A/B-70A
551004
EAMC-30-32-8-11
552157
EAMK-A-D40-44A/C
–
1322185
EAMM-A-D40-70A-S11)
1561532
EADS-F-D40-70A
550982
EAMM-A-D40-87A
530082
EAMF-A-44A/B-87A
551004
EAMC-30-32-8-11
552157
EAMK-A-D40-44A/C
–
1322186
EAMM-A-D40-87A-S11)
1561533
EADS-F-D40-87A
1) With degree of protection IP65.
2) Tyype discontinued.
3) Only with DNCE-…-LS.
2016/03 – Subject to change 23� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Component parts of the axial kit
Axial kit Comprising:
Motor flange Coupling Coupling housing Seal set
Part No. Part No. Part No. Part No. Part No.
Type Type Type Type Type
DNCE-63
543163
EAMM-A-D60-52B3)
– 533709
EAMC-42-50-12-12
552161
EAMK-A-D60-52B
–
543164
EAMM-A-D60-52C3)
– 533709
EAMC-42-50-12-12
552162
EAMK-A-D60-52C
–
560283
EAMM-A-D60-60G2)
550987
EAMF-A-64A/B-60G/H
543424
EAMC-42-50-11-12
552160
EAMK-A-D60-64B
–
2256696
EAMM-A-D60-60G-G2
2256289
EAMF-A-64B-60G/H-S1
543424
EAMC-42-50-11-12
552160
EAMK-A-D60-64B
–
2256698
EAMM-A-D60-60G-S11)
2253505
EADS-F-D60-60G/H
1454245
EAMM-A-D60-60H
2256289
EAMF-A-64B-60G/H-S1
1455671
EAMC-42-50-12-14
552160
EAMK-A-D60-64B
–
2256697
EAMM-A-D60-60H-S11)
2253505
EADS-F-D60-60G/H
543161
EAMM-A-D60-70A
529945
EAMF-A-64A/B-70A
543424
EAMC-42-50-11-12
552160
EAMK-A-D60-64B
–
2256699
EAMM-A-D60-70A-S11)
8022145
EADS-F-D60-70A
1499402
EAMM-A-D60-80G
2843290
EAMF-A-64C-80G-S1
2138701
EAMC-42-50-12-20
551007
EAMK-A-D60-64C
–
2946762
EAMM-A-D60-80G-S11)
8022146
EADS-F-D60-80G
1977073
EAMM-A-D60-80P
1977113
EAMF-A-64A/C-80P
551005
EAMC-42-50-12-19
551007
EAMK-A-D60-64C
–
2218564
EAMM-A-D60-80P-S11)
2218523
EADS-F-D60-80P
543162
EAMM-A-D60-87A
533140
EAMF-A-64A/B-87A
543424
EAMC-42-50-11-12
552160
EAMK-A-D60-64B
–
1322188
EAMM-A-D60-87A-S11)
1561536
EADS-F-D60-87A
550983
EAMM-A-D60-100A
529947
EAMF-A-64A/C/D-100A
551005
EAMC-42-50-12-19
551007
EAMK-A-D60-64C
–
2256700
EAMM-A-D60-100A-S11)
2253507
EADS-F-D60-100A
1) With degree of protection IP65.
2) Type discontinued.
3) Only with DNCE-…-LS.
Subject to change – 2016/0324 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Permissible axis/motor combinations with parallel kit Technical data � Internet: eamm-u
Motor/gear unit1) Parallel kit
� Increased housing rigidity
� More flexible motor mounting possible
� Larger toothed belt bending radii for improved service life
� Components can be mounted to the kit facing any direction
� Use in combination with third-party motors on request
Type Part No. Type
DNCE-32
With servo motor
EMME-AS-40-… 2153283 EAMM-U-50-D32-40P-78
2154009 EAMM-U-50-D32-40AP-78-S12)
EMMS-AS-40-… 1201591 EAMM-U-50-D32-40A-78
1202302 EAMM-U-50-D32-40A-78-S12)
EMMS-AS-55-… 1210126 EAMM-U-60-D32-55A-91
1210450 EAMM-U-60-D32-55A-91-S12)
EMME-AS-60-… 2619586 EAMM-U-70-D32-60P-96
2619688 EAMM-U-70-D32-60P-96-S12)
EMMS-AS-70-… 2755565 EAMM-U-70-D32-70A-96
2781711 EAMM-U-70-D32-70A-96-S12)
With stepper motor
EMMS-ST-42-… 1201607 EAMM-U-50-D32-42A-78
1202312 EAMM-U-50-D32-42A-78-S12)
EMMS-ST-57-… 1210419 EAMM-U-60-D32-57A-91
1210453 EAMM-U-60-D32-57A-91-S12)
With motor unit3)
MTR-DCI-32S-… 1570862 EAMM-U-50-D32-32B-78
MTR-DCI-42S-… 1577393 EAMM-U-60-D32-42B/C-91
1577380 EAMM-U-60-D32-42B/C-91-S12)
MTR-DCI-52S-… 2755890 EAMM-U-70-D32-52B/C-96
2781778 EAMM-U-70-D32-52B/C-96-S12)
With gear unit
EMGA-40-P-… 1577358 EAMM-U-60-D32-40G-91
EMGC-40-P-… 1577346 EAMM-U-60-D32-40G-91-S12)
EMGA-60-P-…-SAS/SST4) 2748181 EAMM-U-70-D32-60G-96
2778302 EAMM-U-70-D32-60G-96-S12)
EMGA-60-P-…-EAS, 2778393 EAMM-U-70-D32-60H-96
EMGC-60-P-…4) 2781450 EAMM-U-70-D32-60H-96-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the parallel kit.
2) With degree of protection IP65
3) Only with DNCE-…-LS
4) Gear unit drive shaft : EMGA-60-P-…-SAS/-SST11 mm; EMGA-60-P-…-EAS, EMGC-60-P14 mm
2016/03 – Subject to change 25� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Permissible axis/motor combinations with parallel kit Technical data � Internet: eamm-u
Motor/gear unit1) Parallel kit
� Increased housing rigidity
� More flexible motor mounting possible
� Larger toothed belt bending radii for improved service life
� Components can be mounted to the kit facing any direction
� Use in combination with third-party motors on request
Type Part No. Type
DNCE-40
With servo motor
EMMS-AS-55-… 1210438 EAMM-U-60-D40-55A-91
1210458 EAMM-U-60-D40-55A-91-S12)
EMME-AS-60-… 2617488 EAMM-U-70-D40-60P-96
2546123 EAMM-U-70-D40-60P-96-S12)
EMMS-AS-70-… 2786204 EAMM-U-70-D40-70A-96
2786316 EAMM-U-70-D40-70A-96-S12)
EMMS-AS-70-… 1212826 EAMM-U-86-D40-70A-102
1212854 EAMM-U-86-D40-70A-102-S12)
EMME-AS-80-… 2802441 EAMM-U-86-D40-80P-102
2802656 EAMM-U-86-D40-80P-102-S12)
With stepper motor
EMMS-ST-57-… 1210442 EAMM-U-60-D40-57A-91
1210462 EAMM-U-60-D40-57A-91-S12)
EMMS-ST-87-… 1215802 EAMM-U-86-D40-87A-102
1215814 EAMM-U-86-D40-87A-102-S12)
With motor unit3)
MTR-DCI-42S-… 1570950 EAMM-U-60-D40-42B/C-91
1430735 EAMM-U-60-D40-42B/C-91-S12)
MTR-DCI-52S-… 2786802 EAMM-U-70-D40-52B/C-96
2786845 EAMM-U-70-D40-52B/C-96-S12)
MTR-DCI-52S-… 1537046 EAMM-U-86-D40-52B/C-102
1537011 EAMM-U-86-D40-52B/C-102-S12)
With gear unit
EMGA-40-P-… 1577165 EAMM-U-60-D40-40G-91
EMGC-40-P-… 1435968 EAMM-U-60-D40-40G-91-S12)
EMGA-60-P-…-SAS/SST4) 2785471 EAMM-U-70-D40-60G-96
2785542 EAMM-U-70-D40-60G-96-S12)
EMGA-60-P-…-EAS, 2786101 EAMM-U-70-D40-60H-96
EMGC-60-P-…4) 2786137 EAMM-U-70-D40-60H-96-S12)
EMGA-60-P-…-SAS/SST4) 1586445 EAMM-U-86-D40-60G-102
1586429 EAMM-U-86-D40-60G-102-S12)
EMGA-60-P-…-EAS, 1586496 EAMM-U-86-D40-60H-102
EMGC-60-P-…4) 1586372 EAMM-U-86-D40-60H-102-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the parallel kit.
2) With degree of protection IP65
3) Only with DNCE-…-LS
4) Gear unit drive shaft : EMGA-60-P-…-SAS/-SST11 mm; EMGA-60-P-…-EAS, EMGC-60-P14 mm
Subject to change – 2016/0326 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Permissible axis/motor combinations with parallel kit Technical data � Internet: eamm-u
Motor/gear unit1) Parallel kit
� Increased housing rigidity
� More flexible motor mounting possible
� Larger toothed belt bending radii for improved service life
� Components can be mounted to the kit facing any direction
� Use in combination with third-party motors on request
Type Part No. Type
DNCE-63
With servo motor
EMMS-AS-70-… 1212477 EAMM-U-86-D60-70A-102
1212835 EAMM-U-86-D60-70A-102-S12)
EMME-AS-80-… 2155875 EAMM-U-86-D60-80P-102
2156527 EAMM-U-86-D60-80P-102-S12)
EMME-AS-100-… 1202436 EAMM-U-110-D60-100A-120
1203112 EAMM-U-110-D60-100A-120-S12)
EMMS-AS-100-… 1202436 EAMM-U-110-D60-100A-120
1203112 EAMM-U-110-D60-100A-120-S12)
With stepper motor
EMMS-ST-87-… 1215784 EAMM-U-86-D60-87A-102
1215810 EAMM-U-86-D60-87A-102-S12)
With motor unit3)
MTR-DCI-52S-… 1537000 EAMM-U-86-D60-52B/C-102
1431381 EAMM-U-86-D60-52B/C-102-S12)
MTR-DCI-62S-… 1536988 EAMM-U-110-D60-62B-120
1431443 EAMM-U-110-D60-62B-120-S12)
With gear unit
EMGA-60-P-…-SAS/SST4) 1586347 EAMM-U-86-D60-60G-102
1437163 EAMM-U-86-D60-60G-102-S12)
EMGA-60-P-…-EAS, 1586276 EAMM-U-86-D60-60H-102
EMGC-60-P-…4) 1530837 EAMM-U-86-D60-60H-102-S12)
EMGA-60-P-……-SAS/SST4) 1543240 EAMM-U-110-D60-60G-120
1436183 EAMM-U-110-D60-60G-120-S12)
EMGA-60-P-…-EAS, 1542264 EAMM-U-110-D60-60H-120
EMGC-60-P-…4) 1530621 EAMM-U-110-D60-60H-120-S12)
EMGA-80-P-… 1532949 EAMM-U-110-D60-80G-120
1530875 EAMM-U-110-D60-80G-120-S12)
1) The input torque must not exceed the maximum permissible transferable torque of the parallel kit.
2) With degree of protection IP65
3) Only with DNCE-…-LS
4) Gear unit drive shaft : EMGA-60-P-…-SAS/-SST11 mm; EMGA-60-P-…-EAS, EMGC-60-P14 mm
-H- Note
The clamping component EADT is
required to adjust the toothed belt
pretension with EAMM-U-110.
The motor and/or axis shaft can
optionally be supported with a
counter bearing EAMG.
More information � eamm-u
2016/03 – Subject to change 27� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Protective bellows kit EADB
General technical data
Type EADB-V1- 32 40 63
Max. stroke range of cylinder1) [mm] 10 … 400 10 … 500 10 … 500
Type of mounting Push-on
Via threaded pin
Mounting position Any
Resistance to media Dust, chippings, oil, grease, petrol (� Internet: Resistance to media)
Ambient temperature2) [°C] –10 … +80
Degree of protection to IEC 60529 IP65
Corrosion resistance class CRC3) 3
1) In combination with the protective bellows kit EADB
2) Note operating range of proximity sensors and cylinder
3) Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
Materials
Sectional view
Bellows
1 Connection Anodised wrought aluminium alloy
2 Adapter Polyamide
3 Bellows NBR
4 End piece Anodised wrought aluminium alloy
– O-ring NBR
Note on materials Free of copper and PTFE
RoHS-compliant
Weight [g]
Type EADB-V1- 32 40 63
Stroke [mm]
Product weight
10 … 100 77 116 196
101 … 200 108 153 263
201 … 300 122 172 309
301 … 400 153 209 376
401 … 500 – 227 397
Moving load
10 … 100 35 43 86
101 … 200 66 80 153
201 … 300 80 99 199
301 … 400 111 136 266
401 … 500 – 154 287
2 31 4
Subject to change – 2016/0328 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Travel speed v as a function of tubing length l
1
The protective bellows kit is a leak-
free system.
To prevent unwanted media from be
ing drawn in, the supply and exhaust
air for the kit must be ducted via a
pressure compensation hole in the
connection part 1.
The pressure generated in the protect
ive bellows kit by the positioning mo
tion is primarily defined by the travel
speed and tubing length. The recom
mended tubing length based on the
travel speed of the drive can be read
from the graph.
EADB-V1-32/tubing 8 mm
EADB-V1-40/tubing 16 mm
EADB-V1-63/tubing 16 mm
Tubing size and push-in fitting
[mm]
Tubing O.D.
[mm]
Push-in fitting
Part No. Type
32 8 186109 QS-Gx-8-I
578376 NPQH-DK-G18-Q8-P10
40, 63 16 186350 QS-G¼-12
578344 NPQH-D-G14-Q12-P10
153261 QSH-16-12
Dimensions Download CAD data � www.festo.com
+ = plus stroke length
32 40
Stroke A21) D1 D2 EE L1 L2 WH+A2 A21) D1 D2 EE L1 L2 WH+A2
[mm] max. max.
10 … 100 44
46 14 Gx 12.9 5.4
70 48
57 17 G¼ 16.3 7
78
101 … 200 74 100 77 107
201 … 300 88 114 88 118
301 … 400 117 143 117 147
401 … 500 – – – – – – – 135 165
63
Stroke A21) D1 D2 EE L1 L2 WH+A2
[mm] max.
10 … 100 43
93 17 G¼ 22.4 7
80
101 … 200 68 105
201 … 300 80 117
301 … 400 104 141
401 … 500 117 154
1) The dimension corresponds to the K8 value (extended piston rod) of the cylinder
-H- Note
The push-in fittings in the adjacent
table must be used for the pressure
compensation hole.
Silencers can be used as an alterna
tive. This reduces the travel speed
slightly.
2016/03 – Subject to change 29� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Ordering data – Protective bellows kit
An extended piston rod (order code
K8) � 17 is absolutely essential
when using a protective bellows kit.
The necessary dimension for K8 as a
function of cylinder size and stroke as
well as the corresponding protective
bellows kit are indicated in the table
below:
Order example:
Selected electric cylinder:
DNCE-32-250-BS-“3”P-Q-…K8
The dimension for the corresponding K8 value (see table):
88 mm
Complete type code for electric cylinder:
DNCE-32-250-BS-“3”P-Q-88K8
The corresponding protective bellows kit:
EADB-V1-32-S201-300
Cylinder data Protective bellows kit Cylinder data Protective bellows kit
[mm]
Stroke
[mm]
Dimension
for K8
[mm]
Part No. Type
[mm]
Stroke
[mm]
Dimension
for K8
[mm]
Part No. Type
32 10 … 100 44 570262 EADB-V1-32-S10-100 40 10 … 100 48 570266 EADB-V1-40-S10-100
101 … 200 74 570263 EADB-V1-32-S101-200 101 … 200 77 570267 EADB-V1-40-S101-200
201 … 300 88 570264 EADB-V1-32-S201-300 201 … 300 88 570268 EADB-V1-40-S201-300
301 … 400 117 570265 EADB-V1-32-S301-400 301 … 400 117 570269 EADB-V1-40-S301-400
– 401 … 500 135 570270 EADB-V1-40-S401-500
63 10 … 100 43 570271 EADB-V1-63-S10-100
101 … 200 68 570272 EADB-V1-63-S101-200
201 … 300 80 570273 EADB-V1-63-S201-300
301 … 400 104 570274 EADB-V1-63-S301-400
401 … 500 117 570275 EADB-V1-63-S401-500
Subject to change – 2016/0330 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Foot mounting HNCE
for axial motor attachment
Materials:
Galvanised steel
Free of copper and PTFE
+ = plus stroke length
1 See dimensions for HNC
2 Electric cylinder DNCE
3 Axial kit EAMM-A
4 Servo motor
Dimensions and ordering data
For size AB
AH AO AT AU SA TR US XA XS
[mm]
32 7 32 10.5 4 17.5 163.5 58 71 165.5 46
40 10 36 12.5 4 19.5 194.5 72 90 196 54
63 10 50 15 5 23 232 92 110 237 64
For size CRC1) Weight Part No. Type
[mm] [g]
32 1 160 547949 HNCE-32-AX
40 1 220 547950 HNCE-40-AX
63 1 470 547951 HNCE-63-AX
1) Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
2016/03 – Subject to change 31� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Profile mounting EAHF Materials:
Plate: Anodised aluminium
Clamping piece: Galvanised steel
RoHS-compliant
Dimensions and ordering data
For size AH B1 B2 B3 D1
H1 H2 L1
[mm]
32 32 100 84 66.1 6.6 17.5 26.1 32
40 36 130 108 85.2 9 15.7 23.3 34
63 50 150 128 104.8 9 22.9 30.4 41
For size CRC1) Weight Part No. Type
[mm] [g]
32 1 175 1098473 EAHF-V1-32-P
40 1 230 1098478 EAHF-V1-40-P
63 1 400 1098481 EAHF-V1-63-P
1) Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
Subject to change – 2016/0332 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Foot mounting HNC/CRHNC,
for parallel motor attachment
Materials:
HNC: Galvanised steel
CRHNC: High-alloy steel
Free of copper and PTFE
+ = plus stroke length
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
Dimensions and ordering data
For size AB
AH AO AT AU TR US XS
[mm]
32 7 32 6.5 4 24 32 45 46
40 10 36 9 4 28 36 54 54
63 10 50 12.5 5 32 50 75 64
For size
[mm]
with parallel kit
EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
SA XA SA XA SA XA SA XA SA XA
32 215 217 226 228 234.5 236.5 – – – –
40 – – 258.5 260.5 267 269 271.5 273.5 – –
63 – – – – – – 312 317 323 328
For size
[mm]
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
SA XA SA XA SA XA
32 210 212 – – – –
40 – – 249.5 251.5 – –
63 – – – – 299 304
For size Basic version High corrosion protection
[mm]
CRC1) Weight
[g]
Part No. Type CRC1) Weight
[g]
Part No. Type
32 2 144 174369 HNC-32 4 139 176937 CRHNC-32
40 2 193 174370 HNC-40 4 188 176938 CRHNC-40
63 2 436 174372 HNC-63 4 424 176940 CRHNC-63
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor
ted by special tests (� also FN 940082) using appropriate media.
2016/03 – Subject to change 33� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Flange mounting FNC/CRFNG Materials:
FNC: Galvanised steel
CRFNG: High-alloy steel
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
+ = plus stroke length
The flange mounting FNC/CRFNG can
only be mounted on the parallel kits on
page 24.
Dimensions and ordering data
For size E FB
MF R TF UF W
[mm] H13
32 45 7 10 32 64 80 16
40 54 9 10 36 72 90 20
63 75 9 12 50 100 120 25
For size
[mm]
ZF
with parallel kit
EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 203 214 222.5 – –
40 – 242.5 251 255.5 –
63 – – – 297 308
For size
[mm]
ZF
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 198 – –
40 – 233.5 –
63 – – 284
For size Basic version High corrosion protection
[mm]
CRC1) Weight
[g]
Part No. Type CRC1) Weight
[g]
Part No. Type
32 1 221 174376 FNC-32 4 220 161846 CRFNG-32
40 1 291 174377 FNC-40 4 291 161847 CRFNG-40
63 1 679 174379 FNC-63 4 680 161849 CRFNG-63
1) Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor
ted by special tests (� also FN 940082) using appropriate media.
Subject to change – 2016/0334 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Trunnion flange ZNCF/CRZNG Materials:
ZNCF: Stainless steel casting
CRZNG: Electropolished stainless steel
casting
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
+ = plus stroke length
Dimensions and ordering data
For size C2 C3 TD
TK TL TM US XH
[mm] e9
32 71 86 12 16 12 50 45 18
40 87 105 16 20 16 63 54 20
63 116 136 20 24 20 90 75 25
For size XL
with parallel kit
[mm] EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 201 212 220.5 – –
40 – 242.5 251 255.5 –
63 – – – 297 308
For size
[mm]
XL
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 196 – –
40 – 233.5 –
63 – – 284
For size Basic version High corrosion protection
[mm]
CRC1) Weight
[g]
Part No. Type CRC1) Weight
[g]
Part No. Type
32 2 150 174411 ZNCF-32 4 150 161852 CRZNG-32
40 2 285 174412 ZNCF-40 4 285 161853 CRZNG-40
63 2 687 174414 ZNCF-63 4 687 161855 CRZNG-63
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor
ted by special tests (� also FN 940082) using appropriate media.
2016/03 – Subject to change 35� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Trunnion support LNZG
Materials:
Trunnion support: Anodised
aluminium
Plain bearing: Plastic
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For size CR
DA
FK
FN FS H1 HB
KE NH TH UL CRC1) Weight Part No. Type
[mm] D11 H13 ±0.1 H13 ±0.2 [g]
32 12 11 15 30 10.5 15 6.6 6.8 18 32 46 2 83 32959 LNZG-32
40 16 15 18 36 12 18 9 9 21 36 55 2 129 32960 LNZG-40/50
63 20 18 20 40 13 20 11 11 23 42 65 2 178 32961 LNZG-63/80
Trunnion support CRLNZG
Materials:
High-alloy steel
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For size CR
FK
FN FS H1 HB
NH TH UL CRC1) Weight Part No. Type
[mm] D11 ±0.1 H13 ±0.2 [g]
32 12 15 30 10.5 15 6.6 18 32 46 4 205 161874 CRLNZG-32
40 16 18 36 12 18 9 21 36 55 4 323 161875 CRLNZG-40/50
63 20 20 40 13 20 11 23 42 65 4 435 161876 CRLNZG-63/80
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor
ted by special tests (� also FN 940082) using appropriate media.
Subject to change – 2016/0336 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Swivel flange SNC Materials:
Die-cast aluminium
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI + = plus stroke length
1 The pivot pin is protected
against rotation by means of a
spring pin
Dimensions and ordering data
For size CG CP E EK
FL L SR TG
[mm] H14 h14 H9 ±0.2
32 14 34 45 +0.2/–0.5 10 22 13 10 32.5
40 16 40 54 –0.5 12 25 16 12 38
63 21 51 75 –0.6 16 32 21 16 56.5
For size XC
with parallel kit
[mm] EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 215 226 234.5 – –
40 – 257.5 264 269 –
63 – – – 317 328
For size
[mm]
XC CRC1) Weight
[g]
Part No. Type
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 210 – – 2 93 174383 SNC-32
40 – 248.5 – 2 140 174384 SNC-40
63 – – 304 2 331 174386 SNC-63
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
2016/03 – Subject to change 37� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Swivel flange SNCS Materials:
Die-cast aluminium
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
+ = plus stroke length
Dimensions and ordering data
For size CN
E EP EX FL LT MS RA TG
[mm] +0.2 ±0.2 +1
32 10+0.013 45+0.2/–0.5 10.5 14 22 13 15+0.5 14.5 32.5
40 12+0.015 54–0.5 12 16 25 16 17+0.5 17.5 38
63 16+0.015 75–0.6 15 21 32 21 23–0.5 23 56.5
For size XC
with parallel kit
[mm] EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 215 226 234.5 – –
40 – 257.5 264 269 –
63 – – – 317 328
For size
[mm]
XC CRC1) Weight
[g]
Part No. Type
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 210 – – 2 86 174397 SNCS-32
40 – 248.5 – 2 122 174398 SNCS-40
63 – – 304 2 281 174400 SNCS-63
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
Subject to change – 2016/0338 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Swivel flange SNCL Materials:
Die-cast aluminium
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
+ = plus stroke length
Dimensions and ordering data
For size CD
E EW FL L MR TG
[mm] H9 –0.2/–0.6 ±0.2
32 10 45+0.2/–0.5 26 22 13 10 32.5
40 12 54–0.5 28 25 16 12 38
63 16 75–0.6 40 32 21 16 56.5
For size XC
with parallel kit
[mm] EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 215 226 234.5 – –
40 – 257.5 264 269 –
63 – – – 317 328
For size
[mm]
XC CRC1) Weight
[g]
Part No. Type
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 210 – – 2 71 174404 SNCL-32
40 – 248.5 – 2 95 174405 SNCL-40
63 – – 304 2 225 174407 SNCL-63
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
2016/03 – Subject to change 39� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Swivel flange
SNCB/SNCB-…-R3
Materials:
SNCB: Die-cast aluminium
SNCB-…-R3: Die-cast aluminium with
protective coating, high corrosion
protection
Free of copper and PTFE
RoHS-compliant
2 Electric cylinder DNCE
3 Parallel kit EAMM-U
4 Motor unit MTR-DCI
+ = plus stroke length
Dimensions and ordering data
For size CB E EK
FL L MR TG UB
[mm] H14 H9/e8 ±0.2 –0,5 h14
32 26 45+0.2/–0.5 10 22 13 8.5 32.5 45
40 28 54–0.5 12 25 16 12 38 52
63 40 75–0.6 16 32 21 16 56.5 70
For size XC
with parallel kit
[mm] EAMM-U-50 EAMM-U-60 EAMM-U-70 EAMM-U-86 EAMM-U-110
32 215 226 234.5 – –
40 – 257.5 264 269 –
63 – – – 317 328
For size
[mm]
XC
with parallel kit
EAMM-U-D32 EAMM-U-D40 EAMM-U-D60
32 210 – –
40 – 248.5 –
63 – – 304
For size Basic version Variant R3 – High corrosion protection
[mm]
CRC1) Weight
[g]
Part No. Type CRC1) Weight
[g]
Part No. Type
32 2 103 174390 SNCB-32 3 100 176944 SNCB-32-R3
40 2 155 174391 SNCB-40 3 151 176945 SNCB-40-R3
63 2 375 174393 SNCB-63 3 371 176947 SNCB-63-R3
1) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
Subject to change – 2016/0340 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Trunnion mounting kit DAMT Materials:
Galvanised steel
Free of copper and PTFE
The kit can be mounted at any posi
tion along the cylinder profile barrel.
The trunnion mounting kit cannot be
mounted in the vicinity of the motor
when used in combination with the
parallel kit EAMM-U.
1 Max. tightening torque
2 Electric cylinder DNCE
3 Axial kit EAMM-A + = plus stroke length
+½ = plus half stroke length
Dimensions and ordering data
For size B1 C2 C3 TD
TL TM UW XG
[mm] e9
32 30 71 86 12 12 50 65 65
40 32 87 105 16 16 63 75 74.5
63 41 116 136 20 20 90 105 91.5
For size XJ XV Max.
tightening torque
CRC1) Weight Part No. Type
[mm] [Nm] [g]
32 107 86 4+1 1 213 2213233 DAMT-V1-32-A
40 130.5 102.5 8+1 1 388 2214899 DAMT-V1-40-A
63 157.5 124.5 18+2 1 911 2214971 DAMT-V1-63-A
1) Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
Ordering data – Mounting attachments Technical data � Internet: clevis foot
Designation For size Part No. Type Designation For size Part No. Type
Clevis foot LNG Clevis foot LSN
32 33890 LNG-32 32 5561 LSN-32
40 33891 LNG-40 40 5562 LSN-40
63 33893 LNG-63 63 5564 LSN-63
Clevis foot LSNG Clevis foot LSNSG
32 31740 LSNG-32 32 31747 LSNSG-32
40 31741 LSNG-40 40 31748 LSNSG-40
63 31743 LSNG-63 63 31750 LSNSG-63
Clevis foot LBG Right-angle clevis foot LQG
32 31761 LBG-32 32 31768 LQG-32
40 31762 LBG-40 40 31769 LQG-40
63 31764 LBG-63 63 31771 LQG-63
2016/03 – Subject to change 41� Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Ordering data – Mounting components, corrosion-resistant Technical data � Internet: clevis foot
Designation For size Part No. Type
Clevis foot CRLNG
32 161840 CRLNG-32
40 161841 CRLNG-40
63 161843 CRLNG-63
Ordering data – Piston-rod attachments Technical data � Internet: piston-rod attachment
Designation For size Part No. Type Designation For size Part No. Type
Rod eye SGS Rod clevis SGA
32 9261 SGS-M10x1,25 32 32954 SGA-M10x1,25
40 9262 SGS-M12x1,25 40 10767 SGA-M12x1,25
63 9263 SGS-M16x1,5 63 10768 SGA-M16x1,5
Rod clevis SG Self-aligning rod coupler FK
32 6144 SG-M10x1,25 32 6140 FK-M10x1,25
40 6145 SG-M12x1,25 40 6141 FK-M12x1,25
63 6146 SG-M16x1,5 63 6142 FK-M16x1,5
Coupling piece KSZ
32 36125 KSZ-M10x1,25
40 36126 KSZ-M12x1,25
63 36127 KSZ-M16x1,5
Ordering data – Piston-rod attachments, corrosion-resistant Technical data � Internet: piston-rod attachment
Designation For size Part No. Type Designation For size Part No. Type
Rod eye CRSGS Rod clevis CRSG
32 195582 CRSGS-M10x1,25 32 13569 CRSG-M10x1,25
40 195583 CRSGS-M12x1,25 40 13570 CRSG-M12x1,25
63 195584 CRSGS-M16x1,5 63 13571 CRSG-M16x1,5
Self-aligning rod coupler CRFK
32 2305778 CRFK-M10x1,25
40 2305779 CRFK-M12x1,25
63 2490673 CRFK-M16x1,5
Ordering data – Guide units for fixed strokes (recirculating ball bearing guide only) Technical data � Internet: feng
Stroke Part No. Type Stroke Part No. Type
[mm] [mm]
For size 32 For size 40
10 … 100 34494 FENG-32-100-KF 10 … 100 34500 FENG-40-100-KF
10 … 200 34496 FENG-32-200-KF 10 … 200 34502 FENG-40-200-KF
10 … 320 34497 FENG-32-320-KF 10 … 320 34504 FENG-40-320-KF
10 … 400 150290 FENG-32-400-KF 10 … 400 150291 FENG-40-400-KF
10 … 500 34498 FENG-32-500-KF 10 … 500 34505 FENG-40-500-KF
For size 63
10 … 100 34514 FENG-63-100-KF
10 … 200 34516 FENG-63-200-KF
10 … 320 34518 FENG-63-320-KF
10 … 400 34519 FENG-63-400-KF
10 … 500 34520 FENG-63-500-KF
Subject to change – 2016/0342 � Internet: www.festo.com/catalogue/...
Electric cylinders DNCE, with spindle driveAccessories
Ordering data – Guide units for variable strokes Technical data � Internet: feng
For size Stroke With recirculating ball bearing guide With plain-bearing guide
[mm] [mm] Part No. Type Part No. Type
32 10 … 500 34487 FENG-32-…-KF 34481 FENG-32-…
40 10 … 500 34488 FENG-40-…-KF 34482 FENG-40-…
63 10 … 500 34490 FENG-63-…-KF 34484 FENG-63-…
Ordering data – Compensating components in combination with guide unit FENG
Designation For size Part No. Type
32 570305 EADC-V1-32
40 570306 EADC-V1-40
63 570307 EADC-V1-50/63
Permissible proximity sensors in combination with motor units MTR-DCI
Ordering data – Proximity sensor for T-slot, magneto-resistive Technical data � Internet: smt
Type of mounting Switching
output
Electrical connection Cable length Part No. Type
[m]
N/O contact
Insertable in the slot from above, flush
with the cylinder profile, short design
PNP Plug connector M8x1,
3-pin
0.3 574334 SMT-8M-A-PS-24V-E-0,3-M8D
Permissible proximity sensors in combination with servo motors EMMS-AS, stepper motors EMMS-ST or guide units FENG
Ordering data – Proximity sensor for T-slot, magneto-resistive Technical data � Internet: smt
Type of mounting Switching
output
Electrical connection Cable length Part No. Type
[m]
N/O contact
Insertable in the slot from above, flush
with the cylinder profile, short design
PNP Cable, 3-wire 2.5 574335 SMT-8M-A-PS-24V-E-2,5-OE
Ordering data – Proximity sensors for T-slot, magnetic reed Technical data � Internet: sme
Type of mounting Switching
output
Electrical connection Cable length Part No. Type
[m]
N/O contact
Inserted in the slot from above, flush with
the cylinder profile
Contacting Cable, 3-wire 2.5 543862 SME-8M-DS-24V-K-2,5-OE
5.0 543863 SME-8M-DS-24V-K-5,0-OE
Insertable in the slot lengthwise, flush
with the cylinder profile
Contacting Cable, 3-wire 2.5 150855 SME-8-K-LED-24
Ordering data – Connecting cable Technical data � Internet: km8
Assembly Connection Cable length Part No. Type
[m]
Straight socket
Union nut M8, both ends 3-pin 0.5 175488 KM8-M8-GSGD-0,5
1 175489 KM8-M8-GSGD-1
2.5 165610 KM8-M8-GSGD-2,5
5 165611 KM8-M8-GSGD-5
Ordering data – Slot cover for T-slot
Mounting Length Part No. Type
Insertable 2x 0.5 m 151680 ABP-5-S
top related