emergency eye wash/shower - lenco canada · 2019. 4. 4. · the americans with disabilities act...
Post on 25-Sep-2020
2 Views
Preview:
TRANSCRIPT
300
P R O V E N T O U G HP R O V E N T O U G H
Emergency Eye Wash/ShowerEmergency Eye Wash/Shower
SentryWash300.qe 9/26/01 8:18 AM Page 2
Table of Contents & Index
3
Table of Contents
90100 . . . . . . . . . . . . Page 1890101 . . . . . . . . . . . . Page 1990102 . . . . . . . . . . . . Page 1990103 . . . . . . See Price Book
90211 . . . . . . . . . . . . . Page 790235 . . . . . . . . . . . . . Page 790235-2 . . . . . . . . . . . Page 790237 . . . . . . . . . . . . . Page 790237-2 . . . . . . . . . . . Page 790243 . . . . . . . . . . . . . Page 790243-2 . . . . . . . . . . . Page 790243-3 . . . . . . . . . . . Page 790250 . . . . . . See Price Book90250-1 . . . . . See Price Book90251 . . . . . . See Price Book90252 . . . . . . See Price Book90254 . . . . . . See Price Book
90305 . . . . . . See Price Book90306 . . . . . . . . . . . . Page 1690311 . . . . . . See Price Book90312 . . . . . . See Price Book90315 . . . . . . See Price Book90320 . . . . . . . . . . . . Page 1690321 . . . . . . . . . . . . Page 1690322 . . . . . . . . . . . . Page 1790323 . . . . . . . . . . . . Page 1690324 . . . . . . . . . . . . Page 1690325 . . . . . . . . . . . . Page 1790326 . . . . . . . . . . . . Page 1790327 . . . . . . . . . . . . Page 1790328 . . . . . . . . . . . . Page 1790329 . . . . . . . . . . . . Page 1790330 . . . . . . . . . . . . Page 1790331 . . . . . . . . . . . . Page 1790332 . . . . . . . . . . . . Page 1790333 . . . . . . . . . . . . Page 1790334 . . . . . . . . . . . . Page 16
Index90410 . . . . . . . . . . . . . Page 990415 . . . . . . . . . . . . . Page 990420 . . . . . . . . . . . . . Page 990421 . . . . . . See Price Book90422 . . . . . . See Price Book90423 . . . . . . See Price Book90424 . . . . . . See Price Book90424-1 . . . . . See Price Book90425 . . . . . . See Price Book90430 . . . . . . See Price Book90435 . . . . . . See Price Book90436 . . . . . . . . . . . . Page 1090440 . . . . . . . . . . . . Page 1190445 . . . . . . . . . . . . Page 1190450 . . . . . . . . . . . . Page 1190450-4 . . . . . . . . . . Page 1190452 . . . . . . . . . . . . Page 1090455 . . . . . . . . . . . . Page 1190455-4 . . . . . . . . . . Page 1190457 . . . . . . . . . . . . Page 10
90510 . . . . . . . . . . . . Page 1590510-2 . . . . . . . . . . Page 1590510-3 . . . . . . . . . . Page 1590514 . . . . . . See Price Book90520 . . . . . . . . . . . . Page 1590520-2 . . . . . . . . . . Page 1590520-3 . . . . . . . . . . Page 1590520-4 . . . . . . . . . . Page 1590524 . . . . . . See Price Book90530 . . . . . . See Price Book90550 . . . . . . See Price Book90560 . . . . . . See Price Book90561-1 . . . . . See Price Book90562 . . . . . . See Price Book90570 . . . . . . . . . . . . Page 15
90600 . . . . . . . . . . . . Page 1390600-1 . . . . . . . . . . Page 1390600-2 . . . . . . . . . . Page 1390602-1 . . . . . . . . . . Page 1390602-2 . . . . . . . . . . Page 13
General Information . . . . . . . . . . . . . . . . . . . . . . . .4
Optional Accessories . . . . . . . . . . . . . . . . . . . . . .4
Standard Construction . . . . . . . . . . . . . . . . . . . . .5
Emergency Showers . . . . . . . . . . . . . . . . . . . . . . .6Vertical/Ceiling Mounted . . . . . . . . . . . . . . . . . .7Horizontal/Wall Mounted . . . . . . . . . . . . . . . . . .7
Eye/Face & Eye Washes . . . . . . . . . . . . . . . . . . . .8Eye/Face Wall Mounted . . . . . . . . . . . . . . . . . .9Eye/Face Deck & Pedestal Mounted . . . . . . .11Eye Wall Mounted & Pedestal Mounted . . . . .12
NOTE:Test all emergency equipment at least weekly.
Due to the continuing improvement of our products, specifications are subject to change without notice.Please call for information on accessories and replacement components.
Eye Wash/Drench Hose Units . . . . . . . . . . . . . . .13Deck Mounted . . . . . . . . . . . . . . . . . . . . . . . . .14
Safety Stations . . . . . . . . . . . . . . . . . . . . . . . . . . .15Eye Wash and Shower Stations . . . . . . . . . . .16Corrosion-Resistant . . . . . . . . . . . . . . . . . . . .16
Portable UnitsGravity Flow . . . . . . . . . . . . . . . . . . . . . . . . . .17Gravity Flow Eye Wash Preservatives . . . . . .18Personal Eye Wash - Rapid Clear® . . . . . . . . .18
Faucet Mounted UnitsEye Washes . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CONSULT THE SELLSTROM PRICE BOOK FOR PRODUCTS NOT SHOWN IN THIS PUBLICATIONDUE TO THE LACK OF SPACE OR DUE TO RECENT ADDITIONS
SentryWash300.qe 9/26/01 8:18 AM Page 4
Optional Accessories Chart
ABS Plastic Bowl
Hinged stainless steel float-off dust covers
Electrostatically applied epoxy powder coating
Stainless steel and PVC used on corrosionresistant units
Backflow preventer or in-line vacuum breaker toprevent backflow
Flexible stainless steel hose in place of PVC
Under counter hose guide bracket for deckmounted units
Stainless steel and cast brass shower heads
ABS plastic is corrosion resistant and durable.
Stainless steel dust covers resist corrosion and are anintegral part of the outlet head for increased tamperresistance.
Increases corrosion resistance.
Extreme corrosion resistance, even in the harshestenvironments.
Units will meet variety of local plumbing codes.
Hose provides superior abrasion resistance for enhanceddurability.
Prevents hose from tangling or binding. Assures unit iseasily removed from flange for use.
High quality materials provide superior impact corrosionresistance, and resists effects of UV light.
SA
FE
TY
ST
AT
ION
S
FEATURE BENEFIT EM
ER
GE
NC
YS
HO
WE
RS
EY
E/F
AC
EW
AS
HE
S
EY
EW
AS
HE
S
DR
EN
CH
HO
SE
-- ✔ ✔ -- ✔
-- ✔ ✔ ✔ ✔
✔ ✔ ✔ -- ✔
✔ ✔ ✔ -- ✔
-- -- -- ✔ --
-- -- -- ✔ --
-- -- -- ✔ --
✔ -- -- -- ✔
LOCATIONTo comply with OSHA regulations, emergency eye wash and shower equipment must be installed in close proximity to anylocation where hazardous materials are handled. As a rule of thumb, the ANSI standard suggests that the distance from thehazardous materials to the emergency equipment not exceed 100 feet or 10 seconds walking time. However, emergencyequipment should be located closer to the hazard if particularly injurious chemicals are being handled. In such cases, equipmentshould be located within 10 to 20 feet of employees. The location which is selected for emergency equipment should be freefrom obstructions and should be accessible from three sides. Users of the equipment should not have to walk around machineryor other obstacles to reach the unit.
WATER SUPPLYProper operation of emergency equipment requires the availability of a large and continuous supply of potable water. The watersupply must, at a minimum, be capable of delivering the volumes of water required by the ANSI standard. Piping should be atleast as large as the inlet size of of the unit to be installed. The water supply line must also be capable of delivering anuninterruptible flow of water of at least 30 PSI flow pressure.
FLOW DATAThe effectiveness of any piece of emergency equipment in rinsing away contaminant depends solely upon two factors: thevolume of water produced, and the pattern in which it is delivered. Sellstrom units are engineered to provide superiorperformance in these two critical areas.
CORROSION PROTECTIONEmergency equipment is often installed in areas where it is exposed to corrosive materials. In these instances, it is advisable touse equipment which is corrosion resistant. Sellstrom offers a protective epoxy coating as an optional feature. Sellstrom alsooffers units which are constructed entirely of stainless steel or PVC. Selection of the appropriate corrosion resistant unitdepends upon the materials to which the equipment may be exposed. Please call for additional information.
HANDICAPPED ACCESSIBILITYThe Americans with Disabilities Act mandates that workplaces be accessible to, and usable by, physically handicapped persons.Sellstrom responds with an array of "barrier-free" products which will assist in complying with the governmental regulations(28 CRF Part 36) and compliance standards (ANSI 1171-1992).
General InformationThis catalog contains checklists which summarize the provisions of ANSI Z358.1 with respect to each type ofemergency equipment. These "ANSI Compliance Checklists" are found at the beginning of each section of thiscatalog. The checklist can be used to assist in the proper selection, installation and maintenance of emergencyequipment. It can also be used in performing an audit of existing emergency equipment.
OPTIONAL ACCESSORIESSentryWash ®
✔ OPTIONAL ACCESSORY-- NOT APPLICABLE4
SentryWash300.qe 9/26/01 8:18 AM Page 5
Standard Construction Chart
5
Outlet heads
Outlet heads feature:Large diameter, perforated spray cover
Low density, advance polyurethane filter
Integral, self adjusting flow controls located ineach outlet head
Impact resistant ABS plastic body
ABS plastic float-off dust covers
Renewable internal components
Heavy duty 1/2" IPS chrome plated brass stay-open ball valve
Schedule 40 pipe and fittings are hot-dippedgalvanized (inside and out) or chrome platedbrass
Outlet head units are preassembled andfactory tested prior to shipment
Chrome plated forged brass stay-open or selfclosing valves
Heavy duty reinforced PVC or recoiling nylonhoses are standard
10" high volume deluge shower head
Rigid stainless steel pull rod with stainless steelactuating arm
Rugged 1" IPS chrome plated brass ball valve
Valve has chrome plated ball with long lastingTeflon® seals
Schedule 40 pipe and fittings are hot-dippedgalvanized inside and out
Single water inlet supplies both shower andeye wash
Rugged 1" IPS chrome plated brass showervalve and 1/2" IPS chrome plated brass eyewash valve
Unique spray heads deliver more water, over a widerarea, in a more gentle flow, than any other type of outlethead.
Provides soft, wide stream of water to quickly and gentlyrinse away contaminants.
Removes scale, deposits and debris from the water flow.Water Line impurities are kept out of user's eyes.
Assures that a consistent, steady water flow is evenlydistributed among outlet head(s).
Tough corrosion resistant body assures durability andlong life.
Keeps airborne contaminants away from outlet heads.
Internal working components are readily accessible.
Domestic made valve provides generous water flow.Stay-open feature permits "hands-free" operation so thatuser can hold eyes open while flushing contaminants.
Heavy duty pipe and fittings resist corrosion and insuredurability and long life.
Guarantees "hassle free" installation, eliminates "callbacks".
Domestic made valves provide generous water flow.
Hoses resist deterioration and abrasion, and are rated to300 PSI working pressure.
Shower head provides a minimum 30 GPM flow and 20"spray pattern at 60" above floor.
Large sized pull rod is easily located and grasped in anemergency. Components are corrosion resistant.
Domestic made valve provides minimum 30 GPM flow.Stay-open feature permits "hands-free" operation so thatuser can disrobe while flushing contaminants.
Valve provides a large volume of water and resistscorrosion, freeze-up and leaking.
Heavy-duty pipe and fittings provide years of durableservice.
Complete personal protection in a single unit. Minimizesinstallation and maintenance costs.
Domestic made valves resist bending, cracking orbreaking. Valves have heavy-duty brass bodies andstems.
SA
FE
TY
ST
AT
ION
S
FEATURE BENEFIT EM
ER
GE
NC
YS
HO
WE
RS
EY
E/F
AC
EW
AS
HE
S
EY
EW
AS
HE
S
DR
EN
CH
HO
SE
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
-- ✔ ✔ ✔ ✔
✔ ✔ ✔ -- ✔
-- ✔ ✔ -- --
-- ✔ ✔ ✔ ✔
-- -- -- ✔ --
-- -- -- ✔ --
✔ -- -- -- ✔
✔ -- -- -- ✔
✔ -- -- -- --
✔ ✔ ✔ -- ✔
✔ -- -- -- ✔
-- -- -- -- ✔
-- -- -- -- ✔
STANDARD CONSTRUCTIONSentryWash ®
✔ STANDARD CONSTRUCTION-- NOT APPLICABLE
SentryWash300.qe 9/26/01 8:18 AM Page 6
Emergency Showers
At 60" above floorsurface, the waterpattern must be atleast 20" indiameter.(Section 4.1)
Shower head shall bebetween 82" and 96" fromfloor surface.(Section 4.1)
Center of the waterpattern shall be atleast 16" from anyobstructions.(Section 4.1)
Easily located,accessible actuator.(Section 4.3)
"Hands-free" stay-openball valve activates inone second or less.(Section 4.2)
IdentificationIdentify showerlocation with highlyvisible sign. Areaaround shower shallbe well lighted.(Section 4.6.2)
TrainingInstruct all employeesin the proper use ofemergency shower.(Section 4.7)
MaintenanceTest shower at leastweekly. Clean andmaintain as required.(Section 4.7.1)
LocationInstall shower within10 seconds and 100feet of hazard.(Section 4.6.1)
Shower mustprovide 30 gallonsof water per minute.(Section 4.1)
ANSI COMPLIANCE CHECKLISTThe American National Standards Institute hasissued ANSI Standard Z358.1-1990 whichestablishes minimum performance requirementsfor emergency showers. This Standard also helpsemployers develop an emergency showerprogram by providing information that pertains
to the installation, testing, training andmaintenance of emergency equipment.This checklist summarizes the requirements ofANSI Z358.1 relating to emergency showers.Section references are to ANSI Z358.1-1998.Use this checklist to evaluate the showers in yourplant area.
20"
82"-96"
60"
EMERGENCY SHOWERSSentryWash ®
✔
✔
✔
✔
✔ ✔
✔
✔
✔
✔
6
SentryWash300.qe 9/26/01 8:18 AM Page 7
Emergency Showers
7
Shower Head• 10" blue ABS plastic shower head delivers 30 GPM at 30 PSI• Spray Pattern is 20" diameter at 60" above floorValve• 1" IPS chrome plated brass stay-open ball valve, furnished with stainless steel actuating
arm and stainless steel pull rod• Valve is made in the USAPipe and Fittings• 1" IPS Schedule 40 hot-dipped galvanized steel pipe and fittingsSupply• 1" IPS female inlet
Additional ModelsITEM # 90235-2Same features as 90235 except with stainless steel shower head for high corrosion resistanceITEM # 90237Same features as 90235 except with self-closing ball valve. Shower closes instantly when handle isreleasedITEM # 90237-2Same features as 90237 except with stainless steel shower head for high corrosion resistance
Vertical/Ceiling Mounted
Shower Head• 10" blue ABS plastic shower head delivers 30 GPM at 30 PSI• Spray Pattern is 20" diameter at 60" above floorValve• 1" IPS chrome plated brass, slow self-closing valve with pull chain and ring • Shower operates for up to 10 seconds after chain is released• Valve is made in the USAPipe and Fittings• 1" IPS Schedule 40 hot-dipped galvanized steel pipe and fittingsSupply• 1" IPS female inlet
Units (except those with self-closing valves) comply
with the requirements of ANSI Z358.1
Horizontal/Wall MountedShower Head• 10" blue ABS plastic shower head delivers 30 GPM at 30 PSI• Spray Pattern is 20" diameter at 60" above floorValve• 1" IPS chrome plated brass stay-open ball valve, furnished with stainless steel actuating
arm and stainless steel pull rod• Valve is made in the USAPipe and Fittings• 1" IPS Schedule 40 hot-dipped galvanized steel nipple with blue ABS plastic elbowSupply• 1" IPS female inlet
Additional ModelsITEM # 90243-2Same features as 90243 except with stainless steel shower head for high corrosion resistanceITEM # 90243-3Same features as 90243 except with self-closing ball valve. Shower closes instantly when handle isreleased
ITEM # 90235Emergency Showerwith Stay-Open Ball Valve
ITEM # 90211Emergency Showerwith Slow Self-ClosingValve, 3 ft. Pull Chainand 8" Ring
ITEM # 90243Emergency Showerwith Stay-Open BallValve
SentryWash300.qe 9/26/01 8:18 AM Page 8
Eye/Face Washes
"Hands-free" stay- open ball valveactivates in onesecond or less.(Section 7.2)(Section 5.2)
Unit must be capable ofdelivering 3.0 (0.04)gallons of water perminute for 15 minutes.(Section 7.1.4)(Section 5.1.5)
Outlet heads shall bepositioned between33" and 45" from thefloor and at least 6"from the wall ornearest obstruction.(Section 7.4.1)(Section 5.4.1)
Valve actuator shallbe large enough to beeasily located andoperated by the user.(Section 7.2)(Section 5.2)
TrainingInstruct all employees in theproper use of emergencywashes.(Section 7.5)(Section 5.5)
MaintenanceTest wash at leastweekly. Clean andmaintain as required.(Section 7.5)(Section 5.5)
IdentificationIdentify eye/face washwith highly visible sign.Area around eye/facewash shall be welllighted.(Section 7.4.5)(Section 5.4.5)
LocationInstall eye/face washwithin 10 seconds or100 feet of hazard.(Section 7.4.4)(Section 5.4.4)
ANSI COMPLIANCE CHECKLISTThe American National Standards Institute hasissued ANSI Standard Z358.1-1998 whichestablishes minimum performance requirementsfor eye/face and eye washes. This Standard alsohelps employers develop an emergency eye/facewash program by providing information thatpertains to the installation, testing, training andmaintenance of emergency equipment.
Protect outlet headswith float-off dustcovers.(Section 7.1.3)(Section 5.1.3)
Controlled lowvelocity flowcompletely rinseseyes and face and isnot injurious to user.(Section 7.1.1)(Section 5.1.1)
Connect unit touninterruptible watersupply with at least30 PSI flow pressure.(Section 7.4.2)(Section 5.4.2)
EYE/FACE WASHES & EYE WASHES
✔
SentryWash ®
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
8
This checklist summarizes the requirements ofANSI Z358.1 relating to eye/face and eyewashes. Section references in black are to ANSIZ358.1-1998 for eye/face washes. Sectionreferences in blue are to ANSI Z358.1-1998 foreye washes. Use this checklist to evaluate theeye/face washes in your plant area.
SentryWash300.qe 9/26/01 8:18 AM Page 9
Eye/Face Washes
Eye/Face Washes - Wall MountedITEM # 90410Eye/Face Wash with Stay-Open Ball Valve
Outlet Head Assembly• Four outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsValve• 1/2" IPS chrome plated brass stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve is made in the USABowl• 111/2" stainless steelMounting• Heavy-duty corrosion-resistant cast aluminum wall bracketSupply• 1/2" IPS female inletWaste• 11/4" IPS female outletQuality Assurance• Unit is completely assembled and individually water tested prior to
shipment
Additional ModelITEM # 90415Same features as 90410 except with 12" blue ABS plastic bowl
ITEM # 90420Eye/Face Wash with Stay-Open Ball Valve
Outlet Head Assembly• Two outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsValve• 1/2" IPS chrome plated brass stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve is made in the USABowl• 111/2" stainless steelMounting• Heavy-duty corrosion-resistant cast aluminum wall bracketSupply• 1/2" IPS female inletWaste• 11/4" IPS female outletQuality Assurance• Unit is completely assembled and individually water tested prior to
shipment
Units comply with the requirements of ANSI Z358.1 9
SentryWash300.qe 9/26/01 8:19 AM Page 10
ITEM # 90452Eye/Face Wash with Stay-Open Ball Valve
Outlet Head Assembly• Four outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated supply armsValve• 1/2" IPS chrome plated brass stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve is made in the USABowl• 111/2" stainless steelMounting• 11/4" IPS hot-dipped galvanized steel pipe and fittings• 9" aluminum floor flangeSupply• 1/2" IPS male inletWaste• 11/4" IPS female outletQuality Assurance• Valve, bowl and head assembly are factory assembled and individually
water tested prior to shipment
Additional ModelITEM # 90457Same features as 90452 except with blue ABS plastic bowl
Eye/Face Washes
11
Eye/Face Washes - Deck MountedITEM # 90436Recessed Eye/Face Wash with Push-Down Control
Outlet Head Assembly• Four outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsValve• 1/2" IPS brass stay-open ball valve activated by push-down knob• Valve is mounted on aluminum bracket for concealed installation below
counter• Valve is made in the USABowl• 13" flanged stainless steel bowl for recessed mounting in countertop• Furnished with all necessary hardware for installationSupply• 1/2" IPS male inletWaste• 11/4" IPS female outletQuality Assurance• Bowl unit with outlet heads and valve assembly are factory assembled and
individually water tested prior to shipment
Eye/Face Washes - Pedestal Mounted
Units comply with the requirements of ANSI Z358.110
SentryWash300.qe 9/26/01 8:20 AM Page 11
Eye Washes
Eye Washes - Wall Mounted
Eye Washes - Pedestal Mounted
ITEM # 90440Eye Wash with Stainless Steel Bowl and Stay-Open Ball Valve
Outlet Head Assembly• Two outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsValve• 1/2" IPS chrome plated brass stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve is made in the USABowl• 111/2" stainless steelMounting• Heavy-duty corrosion-resistant cast aluminum wall bracketSupply• 1/2" IPS female inletWaste• 11/4" IPS female outletQuality Assurance• Unit is completely assembled and individually water tested prior to shipment
Additional ModelITEM # 90445Same features as 90440 except with 12" blue ABS plastic bowl
ITEM # 90450Eye Wash with Stay-Open Ball Valve
Outlet Head Assembly• Two outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow),
filter to remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsValve• 1/2" IPS chrome plated stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve is made in the USABowl• 111/2" stainless steelMounting• 11/4" IPS hot-dipped galvanized steel pipe and fittings• 9" aluminum floor flangeSupply• 1/2" IPS female inletWaste• 11/4" IPS female outletQuality Assurance• Valve, bowl and head assembly are factory assembled and individually water
tested prior to shipment
Additional ModelsITEM # 90450-4Same features as 90450 except Hand/Foot ControlITEM # 90455Same features as 90450 except with 12" blue ABS plastic bowlITEM # 90455-4Same features as 90455 except with Hand/Foot Control
Units comply with therequirements of ANSI Z358.1 11
SentryWash300.qe 9/26/01 8:20 AM Page 12
Eye Wash/Drench Hose
ANSI COMPLIANCE CHECKLISTANSI Standard Z358.1 provides that drench hoseunits may supplement, but may not be used inplace of, dedicated eye wash units. We offer aseries of units which meet the requirements forboth an eye wash and a drench hose. These dualpurpose units can be used to combine an eyewash and a drench hose into a single versatile,economic unit.
This checklist summarizes the requirements forboth eye washes and drench hoses. Sectionreferences are to ANSI Z358.1-1998 (Section 5,“Eye Washes” and Section 8, “Drench Hoses”).Where the requirements of these sectionsoverlap, the more stringent of the two is stated.Use this checklist to verify the proper installation,performance and maintenance of dual purposeeye wash/drench hose units.
TrainingInstruct all employees in theproper use of emergency eyewash/drench hose units.(Section 5.5 and 8.5)
MaintenanceTest eye wash/drenchhose unit at least weekly.Clean and maintain asrequired.(Sections 5.5 and 8.5)
IdentificationIdentify eyewash/drench hose unitwith highly visible sign.Area around unit shallbe well lighted.(Sections 5.4 and 8.4)
Valve shall go from"off" to "on" in onesecond or less andremain activated untilintentionally shut off.(Sections 5.2 and 8.2)
Outlet heads shallbe protected fromairbornecontaminants.(Section 5.1)
Valve actuator shall beeasily located andoperated by the user.(Sections 5.2 and 8.2)
Unit must deliver atleast 3.0 gallons ofwater per minute for15 minutes. (Sections 5.1 and 8.1)
Controlled, low velocity flowcompletely rinses eyes andis not injurious to user.(Section 5.1.1 and 8.1)
Outlet heads shall bepositioned between 33"and 45" from the floor andat least 6" from the wall ornearest obstruction.(Section 5.4)
LocationInstall eye wash/drench hoseunit within 10 seconds or 100feet of hazard.(Section 5.4.4)
Connect unit touninterruptible watersupply with at least 30PSI flow pressure.(Section 5.4.2)
EYE WASH/DRENCH HOSE UNITS
✔
SentryWash ®
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
12
SentryWash300.qe 9/26/01 8:20 AM Page 13
Eye Wash/Drench Hose
Drench Hose Units - Deck MountedOutlet Head Assembly• Two outlet heads • Each head has self-regulating flow control (to assure soft, balanced flow), filter to
remove debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted side by side on chrome plated brass elbow fittingsValve• Chrome plated forged brass squeeze valve activated by lever handle• Valve has locking clip which engages when handle is depressed, providing "hands free"
operation• Valve stays open until locking clip is released• Valve is made in the USAHose• 8' reinforced PVC hose• 300 PSI maximum rated working pressure• Recommended pressure for unit is 80 PSI maximumMounting• Chrome plated brass deck flange for countertop mounting• Flange has handle locator guide to assure that spray heads and handle face forward at
all timesSupply• 3/8 " IPS male swivel-type inletQuality Assurance• Unit is completely assembled and individually water tested prior to shipment
Mounting for additional model #90602-2• Epoxy-coated bracket with spring clips to hold unit on wall• Clips assure that spray heads and handle face forward at all times
Dual purpose eyewash/drench hose units meetthe requirements of ANSIZ358.1 for both eye washesand drench hoses. The sprayhead assembly can be left inthe deck flange for use as afixed eye wash, or the headassembly can be removed touse as a drench hose. Unitseliminate the need forseparate eye washes anddrench hoses. Ideal for areassuch as laboratories whereversatile, space-savingdesigns are required.
Units comply with the requirements of ANSI Z358.1 for both eye washes and drench hoses.
Outlet Head Assembly• Single outlet head• Each head has self-regulating flow control (to assure soft, balanced flow), filter to remove
debris from water, and float-off dust cover• All wearing components are located in head for ease of serviceValve• Chrome plated forged brass squeeze valve activated by stainless steel lever handle• Valve closes when handle is released• Valve is made in the USAHose• 8' reinforced PVC hose• 300 PSI maximum rated working pressure• Recommended pressure for unit is 80 PSI maximumMounting• Nylon deck flange for countertop mounting• Furnished with locknut and washer for securing to counterSupply• 3/8" IPS male swivel-type inletQuality Assurance• Unit is completely assembled and individually water tested prior to shipment
Mounting for addtional model #90600-2• Epoxy-coated hook to hold unit on wall
ITEM # 90600-1Deck MountedDrench Hose
ITEM # 90602-1Deck Mounted Eye Wash/Drench Hose
Additional ModelsITEM # 90600Same features as 90600-1except unmounted hand helddrench hoseITEM # 90600-2Same features as 90600-1except wall mounted
Additional ModelITEM # 90602-2Same features as 90602-1except wall mounted
13
SentryWash300.qe 9/26/01 8:20 AM Page 14
Safety Stations
ANSI COMPLIANCE CHECKLISTThe American National Standards Institute hasissued ANSI Standard Z358.1-1998 whichestablishes minimum performance requirementsfor safety stations. This Standard also helpsemployers develop an emergency safety station
program by providing information that pertains tothe installation, testing, training and maintenanceof emergency equipment. Please refer to ANSIZ358.1-1998 for additional details.
TrainingInstruct all employees in theproper use of safety station.(Section 9.5)
LocationInstall safety station within 10seconds or 100 feet of hazard.(Section 9.4)
MaintenanceTest safety station at leastweekly. Clean and maintainas required. (Section 9.5)
Outlet heads must bepositioned between 33" and45" from the floor and atleast 6" from the wall ornearest obstruction. (Section 5.4)
Shower valve must besimple to operate and gofrom "off" to "on" in onesecond or less.(Section 4.5)
Eye wash equipment mustdeliver at least 0.4 gallons ofwater per minute for 15 minutes. (Section 5.1)
Eye wash valve actuatormust be easily located andoperated by the user.(Section 5.2)
Eye wash valve must gofrom "off" to "on" in onesecond or less, (Section 5.2)and remain activated untilintentionally shut off.
Shower actuator must beeasily located and readilyaccessible to user.(Section 4.3)
Protect outlet heads fromairborne contaminants.(Section 5.1)
IdentificationIdentify safety station withhighly visible sign. Areaaround safety station shallbe well lighted. (Section 9.4)
Shower must provide 30gallons of water per minute.(Section 4.5)
Shower head must be 82"– 96" above floor surface.(Section 4.1)
At 60" above floor surface,the water pattern must be atleast 20" in diameter.(Section 4.5)
G1902
SAFETY STATIONSSentryWash ®
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
14
SentryWash300.qe 9/26/01 8:20 AM Page 15
Safety Stations
Eye Wash And ShowerShower Head• 10" blue ABS plastic shower head delivers 30 GPM at 30 PSI• Spray pattern is 20" diameter at 60" above floorShower Valve• 1" IPS chrome plated brass stay-open ball valve, furnished with stainless steel actuating
arm and stainless steel pull rod• Valve is made in the USAEye Wash Outlet Head Assembly• Two outlet heads• Each head has self-regulating flow control (to assure soft, balanced flow), filter to remove
debris from water, and float-off dust cover• All wearing components are located in head for ease of service• Heads are mounted on chrome plated brass supply armsEye Wash Bowl• 111/2" stainless steelEye Wash Valve• 1/2" IPS chrome plated brass stay-open ball valve• Activated by epoxy coated cast aluminum flag handle• Valve made in USAPipe and Fitting• 11/4" IPS Schedule 40 hot-dipped galvanized steel pipe and fittings with 9" cast aluminum
floor flangeSupply• 11/4" IPS female top or side inletWaste• 11/4" IPS female outletQuality Assurance• Eye wash frame is factory assembled and individually water tested prior to shipment
Additional ModelsITEM # 90510-2Same features as 90510 except with 10" stainless steel shower headITEM # 90510-3Same features as 90510 except with self-closing ball valve on showerITEM # 90520Same features as 90510 except with 12" blue ABS plastic eye wash bowlITEM # 90520-2Same features as 90520 except with 10" stainless steel shower headITEM # 90520-3Same features as 90520 except with self-closing ball valve on showerITEM # 90520-4Same features as 90520 except with Hand/Foot control
Corrosion-ResistantSame specs as above unless otherwise indicated below:
Shower Head• 10" blue ABS plastic shower head delivers 30 GPM at 30 PSIShower Valve• 1" IPS stainless steel stay-open ball valve, furnished with stainless steel actuating
arm and stainless steel pull rodEye Wash Outlet Head Assembly• Two corrosion-resistant outlet heads• Heads are mounted on stainless steel supply armsEye Wash Valve• 1/2" IPS stainless steel stay-open ball valve• Activated by stainless steel flag handlePipe and Fittings• 11/4" IPS Type 304, Schedule 40 stainless steel pipe and fittings with
5" stainless steel floor flange
ITEM # 90510Safety Station withStainless Steel Bowland Stay-Open BallValves
Units (except those with self-closing valves) comply
with the requirements of ANSI Z358.1
15
ITEM # 90570Corrosion-Resistant All Stainless SteelSafety Station withPlastic Shower Headand Stay-Open BallValves
SentryWash300.qe 9/26/01 8:21 AM Page 16
16
Portable Units
Portable Units - Gravity Flow 16 GallonsITEM # 9032016 Gallon Gravit-Eye® Gravity Flow Eye Wash
Tank• 16 Gallon, high density FDA green polyethylene• Tank has heavy wall construction and reinforced ribs to support weight of unit• Approximate dimensions: 201/2" H x 21"W x 181/2"DEye Wash Solution• Fill with clean potable water and add Redi-Sep® bacteriostatic additive
furnished with unit• Additive protects against growth of bacteria, fungus, algae and acanthamoeba• Additive can be ordered separately for refill purposesOutlet Heads• Integral full flow nozzles are activated by pulling down yellow eye wash tray• Swing tray up to storage position to stop flowDrain• Water is directed into drain opening in tank basin• Basin has 3' long drain hose to direct discharge into floor drain, storage tank. etc.Mounting• Furnished with zinc plated steel bracket for wall mounting or resting on flat
surface• Spray heads should be approximately 42" from the floor in "on" positionDischarge Time• Flow duration over 15 minutes• Minimum flow rate .4 gallons per minuteWeight• 19 lbs. empty, 145 lbs. full
AccessoryITEM # 90334 - 16 Gallon Dust CoverOne motion of pulling down on the dust cover flap initiates eye wash flow
ITEM # 903066 Gallon Gravit-Eye® Gravity Flow Eye Wash
Tank• 6 Gallon, high density FDA green polyethylene• Tank has heavy wall construction and reinforced ribs to support weight of unit• Approximate dimensions: 23" H x 151/2"W x 131/2"DEye Wash Solution• Fill with clean potable water and add Redi-Sep® bacteriostatic additive
furnished with unit• Additive protects against growth of bacteria, fungus, algae and acanthamoeba• Additive can be ordered separately for refill purposesOutlet Heads• Integral full flow nozzles are activated by a pull of the yellow retaining stripDrain• Water is directed into drain opening in tank basin• Basin has 3' long drain hose to direct discharge into floor drain, storage tank. etc.Mounting• Furnished with zinc plated steel bracket for wall mounting or resting on flat
surface• Spray heads should be approximately 42" from the floorDischarge Time• Flow duration over 6 minutes• Minimum flow rate .4 gallons per minuteWeight• 13 lbs. empty, 58 lbs. full
Portable Units - Gravity Flow 6 Gallons
Refer to page 37 Maintenance Recommendation for gravity flow units.
Unit complies with therequirements of ANSI Z358.1
Replacement Parts for16 & 6 Gallon Gravity Flow UnitsItem# 90323 Test Log Cards (100)Item# 90321 Drain HoseItem# 90324 Mounting Bracket
Unit complies with the requirements of ANSIZ358.1 for use as a personal eye wash.
SentryWash300.qe 9/26/01 8:21 AM Page 17
ITEM # 90328 - 4 oz. BottleITEM # 90329 - 16 oz. BottleITEM # 90330 - 32 oz. BottleITEM # 90331 - 16 oz. Single Bottle StationITEM # 90332 - 32 oz. Single Bottle StationITEM # 90333 - 32 oz. Double Bottle StationRapid-Clear™ Sterile Solutions
Sterile Eye Wash Solution• For emergency use to flush water soluble acid, alkalis, or loose particulate
contamination from the eyes and skin• Provides a sterile, buffered, preserved, saline solution, pH balanced to be
similar to human tears• Instant access from pull-out bottles in a durable wall-mounted plastic
backboard with easy to follow use directions• Mounts easily to the wall with screws (not included)• Tamper-evident seal ensures sterile solution• Every bottle is clearly date-coded for easy inspection• Easy to open twist-off cap• Unbreakable, flexible polyethylene bottles with a large opening allow full flow
for rapid irrigation of eyes or skin17
Personal Eye Wash - Rapid-Clear™
Gravity Flow Eye Wash Preservatives
Maintenance Recommendation
Use Rapid-Clear™ or Redi-Sep® eyewash additives.These solutions requirereplacement only once every 6 months oras scheduled inspections indicate.Theseoptions may be used to fill any brand ofgrav i ty f low eye wash s ta t ion orpressurized tanks.
The use of Rapid-Clear™ buffered,isotonic saline solution offers greatercomfort during use and greater protectionfor an injured employee.
Redi-Sep® potable water preservative isan economical means of providing asafer eye wash product.
ITEM # 90322 - 8 oz. Concentrate
Redi-Sep®
• Water preservative for use in any gravity flow eye wash unit• Tamper-evident seal for your protection• Every bottle is clearly date-coded for easy inspection• The solution has an in service life of 6 months• 8 oz. bottle is mixed with potable water at a minimum level of 5 gallons and
a max level of 20 gallons
ITEM # 90325 - 1 Gallon PremixITEM # 90326 - 70 oz. ConcentrateITEM # 90327 - 180 oz. Concentrate
Rapid-Clear™ Premix and Concentrate• Water preservative for use in any gravity flow eye wash unit• Provides a buffered, preserved, saline solution, pH balanced to be similar to
human tears• Tamper-evident seal for your protection• Every bottle is clearly date-coded for easy inspection• The solution has an in service life of 6 months• 1 Gallon premix is ideal when potable water not available• 70 oz. concentrate used for stations up to 6 gallons• 180 oz. concentrate used for stations up to 16 gallons
Unit complies with therequirements of ANSI Z358.1
for use as a personal eye wash.
Personal Eye Washes
SentryWash300.qe 9/26/01 8:21 AM Page 18
18
Faucet Mounted Eye Washes
ITEM # 90100Eye Wash with Adjustable Aerated Outlet Heads 3" Apart
Outlet Heads• Chrome plated brass aerated outlet heads are mounted 3" apart• Heads angle forward toward user• Angle of heads is adjustable to permit full coverage and avoid splashing on
counter or floor• Furnished with float-off dust covers to protect heads
Accessory: Dust covers with chains (as shown) for attaching to unitValve• Chrome plated forged brass diverter valve• Pull knob to activate eye wash; water pressure holds eye wash in operation
leaving user's hands free• Push knob or turn off faucet to return to normal faucet operationInlet• Valve body has 55/64"-27 female thread• Units are furnished with 3 adapters for attaching to most commonly used
types of faucet (15/16"-27, 13/16"-27, 3/8" IPS)Outlet• Furnished with removable aerator on bottom outlet• Adapter to convert to 3/8" IPS female thread is availableQuality Assurance• Eye wash is completely assembled and individually water tested prior to
shipment
Important NoteFaucet mounted eye washes, whether manufactured by Sellstrom or others, require two motions to activateunit (turn on faucet, pull knob). Therefore, while they meet some requirements of ANSI Z358.1-1990, Sellstromdoes not believe that they are adequate or acceptable substitutes for dedicated, plumbed-in eye washequipment. Sellstrom offers them solely as supplemental units for secondary protection.
Users of faucet mounted eye washes should be instructed to use cold water only with this type of eye wash.Use of hot water may cause scalding.
Faucet mounted eye washes convert any standard faucet into an emergency eye wash station withoutinterfering with normal faucet operation. They can be installed at sinks close to where accidents may occur.Unlike self-contained or personal eye washes, they afford the user an unlimited water supply for completerinsing and cleansing.
To operate the faucet mounted eye wash, simply turn on water and pull knob. Two gentle streams of water aredelivered through the outlet heads. Push knob or turn off faucet to return faucet to normal operation.
Faucet Mounted Eye Washes
SentryWash300.qe 9/26/01 8:21 AM Page 19
Faucet Mounted Eye Washes
19
Faucet Mounted Eye WashesITEM # 90101Eye Wash with Adjustable Aerated Outlet Heads 5" Apart
Outlet Heads• Chrome plated brass aerated outlet heads are mounted 5" apart• Heads point inward toward user's eyes and face• Ideal for use on gooseneck faucet• Angle of outlet heads is adjustable to permit full coverage and avoid
splashing on counter or floor• Furnished with float-off dust covers to protect heads
Accessory: Dust covers with chains (as shown) for attaching to unitValve• Chrome plated forged brass diverter valve• Pull knob to activate eye wash; water pressure holds eye wash in operation
leaving user's hands free• Push knob or turn off faucet to return to normal faucet operationInlet• Valve body has 55/64"-27 female thread• Units are furnished with 3 adapters for attaching to most commonly used
types of faucet (15/16"-27, 13/16"-27, 3/8" IPS)Outlet• Furnished with removable aerator on bottom outlet• Adapter to convert to 3/8" IPS female thread is availableQuality Assurance• Eye wash is completely assembled and individually water tested prior to
shipment
ITEM # 90102Eye Wash with Non-Adjustable Solid Stream Outlet Heads
Outlet Heads• Chrome plated brass nonaerated outlet heads are mounted 3" apart• Heads angle forward toward user• Angle of outlet heads is not adjustable • Furnished with float-off dust covers to protect heads
Accessory: Dust covers with chains (as shown) for attaching to unitValve• Chrome plated forged brass diverter valve• Pull knob to activate eye wash; water pressure holds eye wash in operation
leaving user's hands free• Push knob or turn off faucet to return to normal faucet operationInlet• Valve body has 55/64"-27 female thread• Units are furnished with 3 adapters for attaching to most commonly used
types of faucet (15/16"-27, 13/16"-27, 3/8" IPS)Outlet• Furnished with removable aerator on bottom outlet• Adapter to convert to 3/8" IPS female thread is availableQuality Assurance• Eye wash is completely assembled and individually water tested prior to
shipment
Refer to page 38 for important information concerning ANSI standards and faucet mounted eye washes.
SentryWash300.qe 9/26/01 8:21 AM Page 20
200
P R O V E N T O U G HP R O V E N T O U G H
General SafetyGeneral Safety
General Safety Catalog 9/20/01 9:02 AM Page 2
Spill Control & Tweezers
3
Be prepared for easy clean-up of emergency spills.
• Universal spill control pillows absorb and contain all types of acid, caustic,solvent or oil
• Special pillows for hydro-fluoric acid• Replacement components available• Cabinet H x W x D: 303/4” x 15” x 91/2” (78.11 cm x 38.10 cm x 24.13 cm)• Cabinet contains:
10 Standard Spill Pillows2 Hydrofluoric Spill Pillows
15 Sorbent Pads2 Total Body Coveralls2 Pairs Gloves2 Chemical Splash Goggles
15 Hazardous Waste Bags with Ties
Spill Control Station
Spill Control StationItem # Description68000 Spill Control StationSpill Control Replacement Parts68120 1 Quart Lab Pillow, Carton/1268130 1 Liter Hydrofluoric Spill Pillow, Carton/468140 1/2 pint Sorbent Pads/Blankets, Carton/1568155 Total Body Coveralls, Large68160 Protective Gloves, Large/1 Pair68170 Chemical Splash Goggles, Pair68180 Hazardous Waste Bags with Ties, Carton/15Box Quantity Pillows68100 1 Gallon Industrial Pillow, Carton/1268110 2 Quart Tubular Pillow, Carton/20
Ideal for splinter removal or as a precision pointed tool for gripping small items.
• Made of high quality stainless steel• Patented sharpening process creates micro burs for precise gripping• High quality Miracle Point® Tweezers is enhanced with a five-power
magnifying lens• Magnifying lens arm is adjustable to various heights• Tweezers available in Splinter Remover Kit containing Magna-Point™
Tweezers, bandages, alcohol wipes and antiseptic ointment• Packaged in resealable plastic pouch
Magna-Point ™ Tweezers
Magna Point™ TweezersItem # Description95051 Magna-Point™ Tweezers95050 Depend-Aid™ Splinter Remover Kit
General Safety Catalog 9/20/01 9:02 AM Page 4
4
Knee Pads
Knee-Pro pads provide the ultimate combination of protection,comfort, durability and reliability.
• Tough hard plastic outer shell covers and protects entire knee• Hinged for natural motion of knee• Lightweight for all-day use• 1/2” (1.27 cm) closed cell foam inner pad provides superior comfort• Elastic woven straps keep pad in place while kneeling, standing and
walking• Speed-clips allow for quick dressing, adjustable while worn• Long lasting abrasion resistant grip-strips • Individual replacement parts available• Re-Fit kit contains 4 straps, 2 grip-strips and 4 speed-clips• Made in USA
Knee-Pro Ultra Flex II ™
Knee-Pro Ultra Flex II™
Item # Description96110 Knee-Pro Ultra Flex II™ Knee PadsKnee-Pro Ultra Flex II™ Replacement Parts96110-1 Grip-Strips96110-2 Speed-Clips96110-3 Straps96110-5 Foam Pad and Rivets96110-4 Re-Fit Kit
Knee-Eze® is a comfortable knee pad at an economical cost.
• Natural sponge rubber molded pad• Comfortable 2” (5.08 cm) elastic straps• Snug and non-binding• Adjustable hook/loop fastening• Two styles available• KE-2 features a super tough second rubber sole• Made in USA
Kneel-Eze ®
Kneel-Eze®
Item # Description96101 KE-1 Knee Pad96102 KE-2 Knee Pad with Sole
General Safety Catalog 9/20/01 9:02 AM Page 5
Sellstrom Manufacturing Co.One Sellstrom DrivePalatine, IL 60067
Toll Free 800.323.7402Phone 847.358.2000Fax 847.358.8564
www.sellstrom.com
© 1999 Sellstrom Manufacturing Co.
• Combines the highest qualitymaterials and workmanship at an excellent price
• Five hard working models covering more than 24 different applications(see application chart on back)
WE HAVETAKEN KNEE PROTECTIONA STEPFURTHER
Finally a complete knee padproduct line that…provides both comfort andprotection for a variety ofenvironments and applications!
#96210 Gentle Knee #96220 Leather Knee
#96230 Softcap Knee #96250 Hardcap Knee
#96240 Fire-retardant Knee
All Pro-Series Knee Padsfeature easyVelcro attachment
General Safety Catalog 9/20/01 9:02 AM Page 9
Phone 800.323.7402Fax 847.358.8564
Knee Protection
Pro-Series Knee PadsIndividually Poly Bagged / Min. Purchase 1 Pair
96210 Gentle Knee96220 Leather Knee96230 Softcap Knee96240 Fire Retardant Knee96250 Hardcap Knee
Item No. Description
NEW
Pro-Series Knee Pad Application Chart
96210 “Gentle Knee”
96220 “Leather Knee”
96230 “Softcap Knee”
96240 “Fire- Retardant Knee”
96250 “Hardcap Knee”
Delicate Surfaces
Harsh Surfaces
Airports
Agriculture
Automotive
Clean Room
Construction
Auto Repair
Flooring
Fire Fighting
Foundries
Maritime
Masonry
Roofing
Sewer
Shipbuilding
Utilities
Welding
Mining
General Industrial
Electrical
Smelters
Refineries
Railroads
✔ ✔ ✔
✔ ✔
✔✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔
✔ ✔
✔
✔ ✔
✔
✔
✔ ✔
✔ ✔
✔
Note: Sellstrom Knee Pads are for industrial use only. Not intended for sports or recreational use.
Strong cordura outerwith comfortable neoprene foam inner.Color: Blue
Durable leather outerwith comfortable neoprene foam inner.Color: Brown
Soft and lightweightrubber cap with neoprene rubber coreinner. Color: Black
Lightweight rubber capwith comfortable neoprene foam inner.Color: Black Pad, GreyCap
Durable plastic hardcap and soft neoprenerubber inner core.Color: Blue Pad, whiteCap
General Safety Catalog 9/20/01 9:02 AM Page 10
top related