errata sheet enviro-seal graphite...
Post on 29-Apr-2018
254 Views
Preview:
TRANSCRIPT
www.Fisher.com
Errata Sheetfor
The following Instruction Manuals
Instruction Manual Title Form Number Date
Design CP Control Valve 5373 February 2001
Design CP Control Valve with ENVIRO-SEAL Bellows Seal Bonnet 5410 November 1998
ENVIRO-SEAL Packing System for Sliding-Stem Valves 5306 December 1996
Design ED and EAD easy-e� Valves Class 125 through 600 5032 January 2001
Design EDR and ETR easy-e� Valves 5050 February 2001
Design EHAD, EHAS, and EHAT Valves 5251 February 1996
1-1/2 x 1 through 8 x 6-Inch Design EHD, EHS, and EHT Valves 5163 September 2000
8- through 14-Inch Design EHD and EHT Sliding-Stem Control Valves 5109 June 1999
Class 125 through 600 Design ES and EAS easy-e� Valves 5030 January 2001
Design ET and EAT easy-e� Valves Class 125 through 600 5081 January 2001
Design EWD, EWS, and EWT Valves through 12 x 8 Inch Size 2376 March 1998
Design EZ easy-e� Control Valve 5118 November 2001
Design EZ-C, ET-C, and EWT-C Cryogenic Sliding-Stem Control Valves 5376 July 2001
Design HP and HPA Control Valve 5299 November 2000
Design YD, YS, and YSC 3-Way Valves 5003 February 2001
Design 1018S Sliding-Stem Valve Sizes DN 15-25-40-50-80-100 (1/2, 1-1/2, 2, 3, and 4-Inch)
5420 June 1997
This errata sheet provides information onENVIRO-SEAL Graphite ULF packing systems. Seetables 2 and 3 and figure 2 for identification ofcomponents in this packing system.
DescriptionENVIRO-SEAL Graphite ULF packing systems areavailable for Fisher easy-e, EH, HP, YD, YS, andCP valves with 9.5, 12.7, 15.9, 19.1, 25.4, and 31.8mm (3/8, 1/2, 5/8, 3/4, 1, and 1-1/4 inch) diametervalve stems and Design 1018S valves with 12 and16mm valve stems.
InstallationInstallation of ENVIRO-SEAL Graphite ULF packingsystems is similar to installation of ENVIRO-SEALGraphite packing systems for easy-e, EH, HP, YD,YS, CP, or 1018S valves. Follow the appropriatewarnings, notes, and instructions as shown in theENVIRO-SEAL Packing System for Sliding-StemValves instruction manual.
Errata SheetMarch 2002 ENVIRO-SEAL� Graphite ULF
ENVIRO-SEAL� Graphite ULFErrata Sheet
March 2002
2
Table 1. Graphite ULF Packing Torque
VALVE STEM SIZE TORQUEVALVETYPE mm Inch N�m Ibf�in Ibf�ft
9.5 3/8 4.3 38 3.2
easy-e�, 12.7 1/2 8.5 76 6.3easy-e�,EH, HP, 19.1 3/4 21 187 16EH, HP,YD, YS 25.4 1 47 420 35
31.8 1–1/4 56 495 41
12.7 1/2 5.3 46 3.9
15.9 5/8 5.0 45 3.7CP
25.4 1 7.1 62 5.2
31.8 1–1/4 4.3 38 3.2
12 - - - 5.5 49 4.11018S
16 - - - 11 94 7.8
Tightening ProcedureTo obtain the target load of 85% compression ofmaximum deflection, perform the following:
� Tighten the packing flange nuts alternately andevenly, keeping the packing flange parallel with thevalve flange, until the Belleville springs arecompressed 100% (or completely flat), as detectedby a rapid increase in nut torque. Refer to theinstruction manual for ENVIRO-SEAL packingsystems for sliding stem valves if you need furtherassistance.
� For graphite ULF packing, loosen each packingflange nut 1/4 turn (90 degrees rotation).
The ‘‘target load’’ of 85% compression has nowbeen reached.
1. The “springs flat” procedure described above isthe preferred method of adjusting ENVIRO-SEALGraphite ULF packing. However, the torque valuesin table 1 can also be used as a guideline for 85%spring compression. These values are based ongenerous lubrication of the packing studs and nutswith Never-Seez lubricant. Loosening of the packingflange nuts is not required when these torques areused.
2. Refer to the appropriate valve and actuatorinstruction manuals when connecting the valve tothe actuator. Under normal conditions, the packingnuts should not require re-tightening.
Figure 1. Belleville Spring Stacking Order for ENVIRO-SEAL Graphite ULF
(Same as for ENVIRO-SEAL Graphite)
A6144/IL
9 SPRINGS
PACKINGFOLLOWER
������
10 SPRINGS
PACKINGFOLLOWER
������� ������� �
������������������ �������������
9 SPRINGS
PACKINGFOLLOWER
���������������������������� �������� �
Note
Fisher does not assume responsibilityfor the selection, use, or maintenanceof any product. Responsibility forproper selection, use, andmaintenance of any Fisher productremains solely with the purchaser.
Parts List
Refer to the appropriate table for part numbers.
ENVIRO-SEAL� Graphite ULFErrata SheetMarch 2002
3
Table 2. Packing Kits for easy-e, EH, HP, YD, and YS ValvesSTEM SIZE DIAMETER
mm InchPACKING RETROFIT(1) PACKING REPAIR(2)
9.5 3/8 RPACKXRT262 RPACKX00592
12.7 1/2 RPACKXRT272 RPACKX00602
19.1 3/4 RPACKXRT282 RPACKX00612
25.4 1 RPACKXRT292 RPACKX00622
31.8 1-1/4 RPACKXRT302 RPACKX006321. Contains key numbers 200, 201, 207, 208, 209, 210, 211, 212, 214, and 217.2. Contains key numbers 207, 208, 209, 210, and 214.
Table 3. Packing Kits for Design CP and 1018S ValvesVALVE SIZE STEM SIZE DIAMETER PACKING
VALVE DESIGNInch mm Inch
PACKINGRETROFIT(1) PACKING REPAIR(2)
1 12.7 1/2 RCPXPKRT742 RCPXPACK272
1-1/2 12.7 1/2 RCPXPKRT752 RCPXPACK282
CP 2 15.9 5/8 RCPXPKRT762 RCPXPACK292CP3 25.4 1 RCPXPKRT772 RCPXPACK302
4 31.8 1-1/4 RCPXPKRT782 RCPXPACK312
1/2, 1, 1-1/2, 2 12 - - -1018S
3, 4 16 - - -Contact your Fisher sales office
1. Contains key numbers 200, 201, 209, 210, 211, 212, 214, 217, and 219.2. Contains key numbers 207, 208, 209, 210, 214, and 219.
Figure 2. ENVIRO-SEAL Graphite ULF Packing
39B9282/A
DESIGN CP (25.4 AND 31.8 mm [1 AND 1-1/4 INCH] STEM SIZESAND DESIGN 1018S (12 AND 16 mm STEM SIZES)
DESIGN CP (12.7, 15.9,AND 19.1 mm [1/2, 5/8,AND 3/4 INCH] STEMSIZES
39B4612/A
DESIGN E
ENVIRO-SEAL� Graphite ULFErrata Sheet
March 2002
4
Fisher Marshalltown, Iowa 50158 USACernay 68700 France Sao Paulo 05424 BrazilSingapore 128461
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy,they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their useor applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice.
Fisher does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Fisher product remains solely with the purchaser.
�Fisher Controls International, Inc. 2002; All Rights Reserved
easy-e, ENVIRO-SEAL, and Fisher are marks owned by Fisher Controls International, Inc., a business of Emerson Process Management.The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners.This product may be covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or underpending patents.
Emerson Process Management
www.Fisher.com
D10
0392
X01
2
8- through 14-Inch Design EHD and EHTSliding-Stem Control ValvesContents
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Principle of Operation 4. . . . . . . . . . . . . . . . . . .
Maintenance 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Packing Lubrication 4. . . . . . . . . . . . . . . . . . . . . . . . . . Packing Maintenance 5. . . . . . . . . . . . . . . . . . . . . . . . .
Replacing Packing 5. . . . . . . . . . . . . . . . . . . . . . . . . . Trim Removal 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Designs EHD, EHT Valve Plug Maintenance 9. . . . . Lapping Seats 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trim Replacement 10. . . . . . . . . . . . . . . . . . . . . . . . . Retrofit: Installing C-seal Trim 12. . . . . . . . . . . . . . . Replacement of Installed C-seal Trim 14. . . . . . . . .
Trim Removal (C-seal Constructions) 14. . . . . . . . Lapping Metal Seats (C-seal Constructions) 15. . Remachining Metal Seats
(C-seal Constructions) 15. . . . . . . . . . . . . . . . . . Trim Replacement (C-seal Constructions) 15. . . .
Actuator Mounting 16. . . . . . . . . . . . . . . . . . . . . . . . .
Parts Ordering 17. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Kits 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bonnet Assembly 18. . . . . . . . . . . . . . . . . . . . . . . . . . Valve Assembly 20. . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction
Scope of ManualThis instruction manual includes installation, mainte-nance, and parts ordering information for 8- through
Figure 1. EH Series Control Valve with Type 667 Actuator
W2992-1/IL
14-inch Design EHD and EHT sliding-stem globe-stylecontrol valves. Refer to separate manuals for instruc-tions covering the actuator, positioner, and accesso-ries.
Only persons qualified through training or experienceshould install, operate, and maintain these valves. Ifyou have any questions about these instructions, con-tact your Fisher Controls sales office or sales repre-sentative before proceeding.
Instruction ManualForm 5109June 1999 Design EH (8- through 14-Inch)
Design EH (8- through 14-Inch)
2
Table 1. Specifications
End Connection Styles(1)
Buttwelding: All available ASME B16.25 sched-ules that are compatible with ASME B16.34 pres-sure/temperature ratings
Flanged Ends: ANSI Class 1500 or 2500� raised-face (RF) or � ring-type joint (RTJ)flanges per ASME B16.5
Shutoff Classifications
See table 2
C-seal trim: High-temperature, Class V. See table 3
Flow Characteristic
Standard Cages: � Linear, � equal percentage,or � modified equal percentage(2)
Whisper Trim� III Cages: � Linear or � modifiedcharacteristics available upon request
Flow Direction
Normally flow down (in through the cage windowsand out through the seat ring) for all cage stylesexcept for applications using either a Whisper TrimIII cage or a diverter cone plug, both of which areflow up only
Additional Specifications
For specifications such as materials, valve plugtravels, and port, yoke boss, and stem diameters,see the Parts List section
Approximate Weights
See table 4
1. The pressure or temperature limits in this manual and any applicable standard limitations should not be exceeded.2. Valves using an equal percentage cage may be travelled an additional 13 mm (1/2 inch) if desired to obtain additional capacity; flow characteristic becomes modified equal percentage.
Table 2. Shutoff Classifications(1)
VALVEDESIGN
ANSILEAKAGE
CLASS
EHDIII—Standard
EHDIV—Optional
EHTIV—Standard
EHTV—Optional
EHT w/ PEEK(2)
Anti-Extrusion Rings V to 316�C (600�F)
1. Per ANSI/FCI 70-22. Poly Ether Ether Ketone
DescriptionThe Design EHD and EHT valves, shown in figure 1,are large, sliding-stem, high-pressure, globe-stylevalves. These valves have metal seats, cage guiding,and push-down-to-close valve plug action.
The Design EHD and EHT valves feature balancedvalve plugs. To provide a seal between the valve plugand cage, the Design EHD valve plug has piston rings;the Design EHT valve plug has a pressure-assistedseal ring.
C-seal trim is available for Design EHD valves, class1500, in sizes 8 and 10 and class 2500, in sizes 8, 10,12, and 14.
With C-seal trim, a balanced valve can achieve high-temperature, Class V shutoff. Because the C-seal plugseal is formed from metal (N07718 nickel alloy, Incon-el 718) rather than an elastomer, a valve equippedwith the C-seal trim can be applied in processes with afluid temperature of up to 593�C (1100�F), providedother material limits are not exceeded.
SpecificationsSpecifications for the Design EHD and EHT valves areshown in table 1.
Installation
WARNING
To avoid personal injury or propertydamage resulting from the sudden re-lease of pressure, do not install thevalve assembly where service condi-tions could exceed the limits given inthis manual or on the appropriate name-plates. Use pressure-relieving devicesas required by government or acceptedindustry codes and good engineeringpractices.
CAUTION
The valve configuration and construc-tion materials were selected to meet par-ticular pressure, temperature, pressuredrop, and controlled fluid conditions.Because some body/trim material com-binations are limited in their pressuredrop and temperature range capabilities,do not apply any other conditions to thevalve without first contacting yourFisher Controls sales office or salesrepresentative.
Design EH (8- through 14-Inch)
3
Table 3. Additional Shutoff ClassificationVALVE DESIGN
(CLASS)VALVE SIZE, INCHES PORT DIAMETER,
INCHESCAGE STYLE ANSI LEAKAGE
CLASS
Design EHD(Class 1500)
810
7
Equal PercentageModified Equal Percentage
Linear (std. cage)Linear (Whisper III, A1, B3, C3)
V (for portdiameters from 2-7/8 through 7-inch withoptional C-seal trim)
Design EHD
810
5-3/8Equal Percentage, Modified Equal Percentage,
Linear (std. cage),Linear (Whisper III, A1, B3, C3, D3)
V (for portdiameters from 2-7/8 through 7-inch withoptional C-seal trim)Design EHD
(Class 2500)1214
7Equal Percentage, Modified Equal Percentage,
Linear (std. cage),Linear (Whisper III, A1, B3, C3, D3)
V (for portdiameters from 2-7/8 through 7-inch withoptional C-seal trim)
Table 4. Approximate Weights (Valve Body and Bonnet Assemblies)
VALVEWEIGHTS
VALVESIZE
Class 1500 Class 2500SIZE,
INCHESButtwelding Ends Flanged Buttwelding Ends Flanged
INCHESKilograms Pounds Kilograms Pounds Kilograms Pounds Kilograms Pounds
8 1400 3100 1700 3700 1900 4100 2200 4700
10 1500 3300 1900 4100 2000 4400 - - - - - -
12 3400 7300 3900 8600 3400 7600 - - - - - -
14 3400 7300 - - - - - - 3400 7600 - - - - - -
If hoisting the valve, use a nylon sling toprotect the painted surfaces. Carefullyposition the sling to prevent damage tothe actuator tubing or any accessories.Also, take precautions to prevent per-sonnel from being injured in case thehoist or rigging slips unexpectedly. Re-fer to table 4 for valve assembly weightsand the appropriate actuator instructionmanual for actuator assembly weights.Be sure to use adequately sized hoistsand chains or slings to handle the valveand actuator assembly.
1. Before installing the valve, inspect the valve, bodycavity, and associated equipment for any damage andforeign material.
2. Clean out all pipelines to remove scale, weldingslag, and other foreign materials before installing thevalve.
Note
If installing a valve with small internalflow passages, such as with WhisperTrim III or Cavitrol� III cages, considerinstalling an upstream strainer to pre-vent the lodging of particles in thesepassages. This is especially important ifthe pipeline cannot be thoroughlycleaned or if the flowing medium is notclean.
3. Install the control valve with the valve body in ahorizontal pipeline and the actuator vertical above thevalve. Other orientations may result in shortened trimlife and difficulty with field maintenance. Flow throughthe valve body must be in the direction indicated bythe flow arrow (key 15, figure 14 or 15) on the valvebody.
Note
Depending on valve body materialsused, post-weld heat treating might beneeded. Post-weld heat treatment candamage internal elastomeric, plastic,and metal parts. Shrink-fit pieces andthreaded connections might also loos-en. In general, if post-weld heat treatingis needed, remove all trim parts. Contactyour Fisher Controls sales office orsales representative for additional in-formation.
4. Use accepted piping and welding practices wheninstalling the valve in the line. For flanged valve bo-dies, use suitable gaskets between the valve bodyflanges and pipeline flanges.
5. Install a three-valve bypass around the controlvalve if continuous operation is required during mainte-nance.
6. If the actuator and valve are shipped separately,see the Actuator Mounting procedure.
7. If the valve was shipped without packing installed inthe packing box, install the packing prior to putting the
Design EH (8- through 14-Inch)
4
valve into service. Refer to instructions given in thePacking Maintenance section of this manual.
Principle of OperationKey numbers referenced in this section are shown infigure 14 for the Design EHD valve and in figure 15 forthe Design EHT valve.
Design EHD and EHT valves are balanced designs.When they are opening or closing, pressure registerson top of the valve plug (key 3) through the registra-tion holes in the plug. The force of the pressure on topof the plug balances the force of the pressure on thebottom of the plug to reduce the actuator force requi-red.
MaintenanceValve parts are subject to normal wear and must beinspected and replaced as necessary. Inspection andmaintenance frequency depends on the severity ofservice conditions. This section includes instructionsfor packing lubrication and maintenance, trim mainte-nance, and lapping of metal seats. All maintenanceoperations can be performed with the valve in the line.
Because of the care Fisher Controls takes in meetingall manufacturing requirements (heat treating, dimen-sional tolerances, etc.), use only replacement partsmanufactured or furnished by Fisher Controls.
WARNING
Avoid personal injury from sudden re-lease of process pressure. Before per-forming any maintenance operations:
� Disconnect any operating lines pro-viding air pressure, electric power, or acontrol signal to the actuator. Be surethe actuator cannot suddenly open orclose the valve.
� Use bypass valves or completelyshut off the process to isolate the valvefrom process pressure. Relieve processpressure on both sides of the valve.Drain the process media from bothsides of the valve.
� Vent the power actuator loadingpressure and relieve any actuator springprecompression.
� Use lock-out procedures to be surethat the above measures stay in effectwhile you work on the equipment.
Table 5. Recommended Packing Flange Nut TorquesSTEM
DIAMETER VALVERATING
N�m Lbf�ft
mm InchesRATING
Min Max Min Max
31 8 1 1/4Class 1500 68 102 50 75
31.8 1-1/4Class 2500 81 122 60 90
50 8 2Class 1500 98 146 72 108
50.8 2Class 2500 115 170 85 125
Refer to table 4 for valve assemblyweights and the appropriate actuatorinstruction manual for actuator assem-bly weights. Due to the size and weightof the valve and actuator assembly, besure adequately sized hoists and chainsor slings are used to handle it. Also,take proper precautions to prevent per-sonnel from being injured if the hoist orrigging slips unexpectedly.
Note
Whenever a gasket seal is disturbed byremoving or shifting gasketed parts,install a new gasket upon reassembly.This is necessary to ensure a good gas-ket seal.
8. After all maintenance is complete, refer to the TrimReplacement procedure to assemble the valve body.
Note
If the valve has ENVIRO-SEAL� live-loaded packing installed, see the FisherControls instruction manual titledENVIRO-SEAL Packing System for Slid-ing-Stem Valves for packing instruc-tions.
If the valve has HIGH-SEAL� live-loadedpacking installed, see the FisherControls instruction manual titledHIGH-SEAL Live-Loaded Packing Sys-tem for instructions.
Packing Lubrication
Note
ENVIRO-SEAL or HIGH-SEAL packingdoes not require lubrication.
A lubricator or lubricator/isolating valve (figure 2) isrecommended for PTFE-impregnated compositionpacking. The lubricator or lubricator/isolating valve isinstalled in place of the pipe plug in the bonnet. Use agood quality silicon-base lubricant. Do not lubricatepacking used in oxygen service or in processes withtemperatures over 260�C (500�F). To operate the lu-
Design EH (8- through 14-Inch)
5
Figure 2. Lubricator and Lubricator/Isolating Valve
���������
���������������� ������10A9421-AAJ5428-DA0832-2/IL
��
��
��
bricator, turn the cap screw clockwise to force lubri-cant into the packing box. The lubricator/isolatingvalve operates the same way except open the isolat-ing valve before turning the cap screw and then closethe isolating valve after lubrication is completed.
Packing Maintenance
WARNING
Personal injury could result from pack-ing leakage. Valve packing was tight-ened before shipment; however, thepacking might require readjustment tomeet specific service conditions.
Valves with ENVIRO-SEAL live-loaded packing orHIGH-SEAL live-loaded packing installed probably willnot require this initial re-adjustment. See the FisherControls instruction manuals titled ENVIRO-SEALPacking System for Sliding-Stem Valves or HIGH-SEAL Live-Loaded Packing System (as appropriate)for packing instructions. To convert an existing pack-ing arrangement to ENVIRO-SEAL packing, refer tothe retrofit kits listed in the parts kit sub-section nearthe end of this manual. Figures 3 and 4 show typicalENVIRO-SEAL packing systems.
For spring-loaded PTFE V-ring packing (figure 6), thespring maintains a sealing force on the packing. Ifleakage is noted around the packing follower (key 13,figure 13), check to be sure the shoulder on the pack-ing follower is touching the bonnet (key 1, figure 13). Ifthe shoulder is not touching the bonnet, tighten thepacking flange nuts (key 5, figure 13) until the shoul-
Figure 3. Typical ENVIRO-SEAL Packing System,Graphite Packing
PACKINGNUT(KEY 212)
PACKINGFLANGE STUD(KEY 200)
PACKINGFLANGE(KEY 201)
WASHERPTFE(KEY 214)
BUSHING(KEY 208)
BUSHING(KEY 207)
BUSHING(KEY 207)
PACKINGRING(KEY 209)
PACKINGRING(KEY 210)
PACKINGRING(KEY 209)
PACKINGBOX RING(KEY 211)A6292 / IL
der on the packing follower is against the bonnet. Ifthe packing leakage is still excessive, replace thepacking by following the Replacing Packing procedure.
If packing leakage is undesirable with other thanspring-loaded PTFE V-ring packing, first try to limit theleakage and establish a stem seal by tightening thepacking flange nuts (key 5, figure 13) to at least theminimum recommended torque in table 5. However,do not exceed the maximum recommended torque intable 5 or excessive friction may result.
If the packing is relatively new and tight on the stem,and if tightening the packing flange nuts does not stopthe leakage, the valve stem may be worn or nicked sothat a seal cannot be made. The surface finish of anew stem is critical for making a good packing seal. Ifthe leakage comes from the outside diameter of thepacking, the leakage may be caused by nicks orscratches around the packing box wall. While replac-ing the packing according to the Replacing Packingprocedure, inspect the stem and packing box wall fornicks or scratches.
Replacing Packing
Key numbers referred to in this procedure are shownin figure 13 unless otherwise indicated.
1. Remove the stem connector cap screws shown infigure 5, and separate the two halves of the stem con-nector. Then exhaust all actuator pressure, if any wasapplied, and disconnect the actuator supply and anyleakoff piping.
Design EH (8- through 14-Inch)
6
Figure 4. ENVIRO-SEAL Packing System, PTFE Packing
PACKING NUT(KEY 212)
PACKINGFLANGE STUD(KEY 200)
PACKINGFLANGE(KEY 201)
PACKINGWASHER(KEY 214)
LOWERWIPER(KEY 218)
LANTERNRING(KEY 216)
PACKING SETPTFE-CARBON/PTFE(KEY 215)
PACKINGBOX RING(KEY 211)
A6293 / IL
2. Remove the hex nuts (key 26) and remove the ac-tuator from the bonnet (key 1). Loosen the packingflange nuts (key 5) so that the packing (key 6, or 7 and 9, figure 6) is not tight on the valve plug stem (key 4, figure 14 or 15). Remove any travel indicatordisk and stem locknuts from the valve plug stemthreads.
WARNING
To avoid personal injury or propertydamage caused by uncontrolled move-ment of the bonnet, loosen the bonnetby following the instructions in the nextstep. Do not remove a stuck bonnet bypulling on it with equipment that canstretch or store energy in any othermanner. The sudden release of storedenergy can cause uncontrolled move-ment of the bonnet.
Note
The following step also provides addi-tional assurance that the valve fluidpressure has been relieved.
3. Hex nuts (key 14) attach the bonnet to the valvebody. Loosen these nuts approximately 3 mm (1/8 inch).Then loosen the body-to-bonnet gasketed joint by eitherrocking the bonnet or prying between the bonnet andvalve body. Work the prying tool around the bonnet until
the bonnet loosens. If no fluid leaks from the joint, pro-ceed with the bonnet removal in step 5.
WARNING
If the cage sticks to the bonnet, proceedcarefully with bonnet removal until thecage windows are accessible. Do notextend hands or arms through the win-dows at this point as a sudden separa-tion of bonnet and cage will cause per-sonal injury. Use a stick or other deviceto thread a rope or sling through thewindows. Use this rigging to secure thecage to the bonnet or hoist to preventdamage or injury should the cage sud-denly separate from the bonnet.
CAUTION
When lifting the bonnet (key 1), be surethat the valve plug and stem assembly(keys 3 and 4, figure 14 or 15) remainson the seat ring (key 6, figure 14 or 15).This avoids damage to the seating sur-faces as a result of the assembly drop-ping from the bonnet after being liftedpart way out. The parts are also easierto handle separately.
4. Remove the hex nuts (key 14, figure 14 or 15) andwashers (key 29, figure 14 or 15). Carefully lift thebonnet off the valve plug stem. If the valve plug as-sembly starts to lift with the bonnet, use a brass orsimilar hammer to tap the end of the stem and tap itback down. Set the bonnet on a protective surface toprevent damage to the bonnet gasket surface.
CAUTION
Use care to avoid damaging gasket seal-ing surfaces.
The Design EHD piston rings (key 8) arebrittle and in two pieces. Use care toavoid damage to the piston ringscaused by dropping or rough handling.
5. Lift the plug assembly (keys 3 and 4, figure 14 or 15) out of the valve body.
6. To remove the cage (key 2, figure 14 or 15), if itremained in the valve body, install eyebolts or similardevices into the 1/2-inch 13-UNC tapped holes in thetop of the cage. Using the eyebolts, carefully lift thecage out of the valve body. Remove the top and bot-
Design EH (8- through 14-Inch)
7
Figure 5. Actuator Mounting
ANTI-ROTATION GROOVE
TRAVEL INDICATOR
STEM CONNECTOR
POINTERSTEM LOCKNUTS
MOUNTING STUDS & NUTS
STEMCONNECTORCAP SCREWS
15A4691-AA2359-2 / IL
tom cage gaskets (key 11, figure 14 or 15). Carefullyremove any residual silver or tin from the gasket sur-faces.
7. Cover the opening in the valve body to protect thegasket surface and to prevent foreign material fromgetting into the valve body cavity.
8. Remove the packing flange nuts, packing flange,upper wiper and packing follower. Carefully push outall the remaining packing parts from the valve side ofthe bonnet using a rounded rod or other tool that willnot scratch the packing box wall. Clean the packingbox and these metal packing parts shown in the figure6 arrangements: packing box ring, spring, lantern ring,washer if used, and packing follower (keys 11, 8, 10,and 13.
9. Inspect the valve plug stem threads for any sharpedges that might cut the packing. Use a whetstone oremery cloth to smooth the threads if necessary.
10. Remove the protective covering from the valvebody cavity, and install the cage using new cage gas-kets (key 11, figure 14 or 15).
11. Install the plug and stem assembly. Be sure theseal ring or piston rings are installed correctly as de-scribed under Trim Replacement.
12. Slide the bonnet over the stem and onto the bon-net studs (key 13, figure 14 or 15).
Table 6. Body-to-Bonnet Bolting Torques
VALVESIZE
VALVE B7, B16, BD, 660 STUDS B8, B8M STUDSSIZE
INCHES
VALVERATING N�m lbf�ft N�m lbf�ft
8 10Class 1500 2710 2000 2035 1500
8, 10Class 2500 4070 3000 3050 2250
12 14Class 1500 8130 6000 6100 4500
12, 14Class 2500 5830 4300 4370 3225
Note
Proper performance of the bolting pro-cedures in step 14 compresses the cagegaskets (key 11, figure 14 or 15) enoughto seal the body-to-bonnet joint.
The prelubricated hex nuts (key 14, fig-ure 14 or 15) referred to in step 14 canbe identified by a black film coating onthe nut threads.
The proper bolting procedures in step14 include, but are not limited to, ensur-ing that the bonnet stud threads areclean, and that the hex nuts are evenlytightened to the specified torque values.
CAUTION
Failure to comply with good bonnet-to-body bolting practices and the torquevalues shown in table 6 may result incage crushing, cage diameter reduction,and/or bonnet deformation. Do not usecheater bars or slug wrenches for thisprocedure.
Hot torquing is not recommended.
13. Lubricate the stud threads and the faces of thehex nuts (key 14, figure 14 or 15) with Never-SeezPure Nickel Special lubricant or equivalent (not neces-sary if new factory prelubricated hex nuts are used).Replace the washers and hex nuts but do not tightenthem. Torque the nuts in a crisscross pattern to nomore than 1/4 of the nominal torque value specified intable 6. When all nuts are tightened to that torque val-ue, increase the torque by 1/4 of the specified nominaltorque and repeat the crisscross pattern. Repeat thisprocedure until all nuts are tightened to the specifiednominal value. Apply the final torque value again and,if any nut still turns, tighten every nut again.
14. Install new packing and the metal packing boxparts according to the appropriate arrangement in fig-ure 6. Slip a smooth-edged pipe over the valve stem,and gently tamp each soft packing part into the pack-ing box.
Design EH (8- through 14-Inch)
8
Figure 6. Packing Arrangements
GRAPHITELAMINATEPACKING RING(KEY 7)
UPPER WIPER (KEY 12)UPPER WIPER (KEY 12)
PACKING FOLLOWER(KEY 13)
FEMALE ADAPTOR(KEY 32)
V-RING (KEY 7)
MALE ADAPTOR(KEY 31)
WASHER (KEY 10)
SPRING (KEY 8)
PACKING BOX RING(KEY 11)
LOWER WIPER(KEY 30)
KEY 61
2
PACKING FOLLOWER(KEY 13)
GRAPHITE LAMINATEPACKING RING (KEY 7)
GRAPHITE FILAMENTPACKING RING (KEY 9)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
3
PACKING FOLLOWER(KEY 13)
PACKING RING(KEY 7)PACKING RING(KEY 7)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
12A8160-A / IL14A3412-B / IL 13A0112-A / IL
���������� ��� ��� ������
�������� ������������������������ ��� ������
���������������������������
UPPER WIPER (KEY 12) UPPER WIPER (KEY 12)
PACKING FOLLOWER(KEY 13)
FEMALE ADAPTOR(KEY 32)
V-RING (KEY 7)
MALE ADAPTOR(KEY 31)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
LOWER WIPER(KEY 30)
KEY 61
2
PACKING FOLLOWER(KEY 13)
GRAPHITE LAMINATEPACKING RING (KEY 7)
GRAPHITE FILAMENTPACKING RING (KEY 9)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
3
PACKING FOLLOWER(KEY 13)
PACKING RING(KEY 7)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
12A7839-A / ILSht 1
14A3414-B / IL 12A8163-A / IL
���������� ������������
�������� ���������������������������������
������������������������
UPPER WIPER (KEY 12)
PACKING FOLLOWER(KEY 13)
PACKING RING(KEY 7)
LANTERN RING(KEY 8)
PACKING BOX RING(KEY 11)
1
2
PACKINGFOLLOWER(KEY 13)
GRAPHITEFILAMENTPACKING RING(KEY 9)
LANTERN RING(KEY 8)
PACKINGBOX RING(KEY 11)
3
1
1
14A3419-B / IL 14A3418-A / IL 13A0029-A / IL
1
GRAPHITELAMINATEPACKING RING(KEY 7) 2
PACKINGFOLLOWER(KEY 13)
GRAPHITEFILAMENTPACKING RING(KEY 9)
LANTERN RING(KEY 8)
PACKINGBOX RING(KEY 11)
3
�������� ������������������������ ��� ������
�������� ���������������������������������
������������������� ������������
������������
������ ������ ������������������ �!�������"������������
������ ������ ����������#$������ ������"������������NOTES:
0.102 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS.
USE ONLY ONE BELOW EACH GRAPHITE LAMINATE RING.
HAS THE APPEARANCE OF FLAT WASHERS PRESSED TOGETHER.
HAS THE APPEARANCE OF A WOVEN OR BRAIDED RING.
1 2
3C0634-1 / IL
Design EH (8- through 14-Inch)
9
15. Slide the packing follower, wiper, and packingflange into position. Lubricate the packing flange studs(key 4) and the faces of the packing flange nuts (key5) and then install the packing flange nuts.
For spring-loaded PTFE V-ring packing: Tightenthe packing flange nuts until the shoulder on the pack-ing follower (key 13) contacts the bonnet (key 1).
For other kinds of packing, except ENVIRO-SEALand HIGH-SEAL: Tighten the packing flange nuts tothe maximum recommended torque shown in table 5.Then, loosen the packing flange nuts and retightenthem to the recommended minimum torque in table 5.
For ENVIRO-SEAL and HIGH-SEAL packing: Seethe Fisher Controls instruction manuals titledENVIRO-SEAL Packing System for Sliding-StemValves or HIGH-SEAL Live-Loaded Packing System(as appropriate) for packing instructions.
16. Mount the actuator on the valve body assembly,and reconnect the actuator and valve plug stem ac-cording to the Actuator Mounting procedure. After thecontrol valve is returned to service, retighten the hexnuts (key 14, figure 14 or 15) to the torque recom-mended in table 6.
Trim RemovalFor C-seal construction, see the appropriate C-sealsections in this instruction manual.
Key numbers referenced in this procedure are shownin figure 14 for the Design EHD valve and figure 15 forthe Design EHT valve except where indicated.
1. Remove the actuator and bonnet by following steps1 through 9 of the Replacing Packing procedure.
2. To remove the seat ring (key 6), remove the capscrews (key 7). Install eyebolts or similar devices inthe 5/8-inch 11-UNC tapped holes (9/16-inch 12-UNCfor an 8 or 10-inch Class 1500 valve). Use the eye-bolts to carefully lift the seat ring out of the valve body.If the seat ring is to be reused, exercise care to protectthe gasket surfaces on the bottom of the seat ring.
3. Remove the spiral wound seat ring gasket or O-ring (key 12).
4. Refer to the following appropriate valve plug main-tenance procedure or to the Lapping Seats procedure.
Design EHD and EHT Valve PlugMaintenanceKey numbers used in this procedure are shown in fig-ure 14 for the Design EHD valve and in figure 15 forthe Design EHT valve.
1. With the valve plug (key 3) removed per the TrimRemoval procedure, proceed as appropriate:
For the Design EHD valve, the piston rings (key 8)are each in two sections; remove the sections from thegrooves in the valve plug.
For all Design EHT valves, work the retaining ring(key 10) off the valve plug with a screwdriver. Careful-ly slide the backup ring and seal ring (keys 9 and 8) offthe valve plug. Additionally, for the Design EHT valvewith Whisper Trim Level D cage, remove the two sec-tions of the piston ring (key 30, figure 15).
2. To replace the valve plug stem (key 4), drive outthe pin (key 5) and unscrew the stem from the valveplug (key 3).
CAUTION
Never reuse an old stem with a newvalve plug. Using an old stem with anew plug requires drilling a new pinhole in the stem. This weakens the stemand may cause the stem to fail in ser-vice. If a new valve plug is required, al-ways order a valve plug, stem, and pinas an assembly. Specify the correct partnumber of each of the three parts butstate that the parts are being ordered asan assembly.
A used valve plug may be reused with anew stem.
3. Thread the new stem into the valve plug until thestem wedges tightly at the end of the thread. Using thevalve plug pin hole as a guide, drill the pin holethrough the stem. Use a 1/4-inch drill for 31.8 mm(1-1/4 inch) stems and a 3/8-inch drill for 50.8 mm(2-inch) stems.
4. Drive in the pin to lock the assembly.
5. If seat lapping is necessary, complete the LappingSeats procedure before installing the Design EHD pis-ton rings or the Design EHT seal ring. Piston ring andseal ring installation instructions and valve body-to-bonnet reassembly instructions are presented in theTrim Replacement procedure.
Design EH (8- through 14-Inch)
10
Table 7. Seat Ring and Seat Ring Cap Screw Lubricants and Recommended Torque for Seat Ring Cap ScrewsRECOMMENDED TORQUE
LUBRICANTVALVESIZE,
INCHES
VALVERATINGCLASS
Spiral Wound Gasket Construction
O-Ring Construction orConstructions forSour Gas ServiceINCHES CLASS
N�m lbf�ft N�m lbf�ft
Lubriplate MAG-1Ni k l N 8 10
1500 61 45 41 30or Nickel NeverSeez Pure Nickel
8, 102500 95 70 61 45
Seez Pure NickelSpecial or 12 14
1500 95 70 61 45S ecial orEquivalent
12, 142500 95 70 61 45
8 101500 47 35 34 25
Molykote 321 R
8, 102500 75 55 47 35
Molykote 321 R
12 141500 75 55 47 35
12, 142500 75 55 47 35
Lapping SeatsA certain amount of leakage should be expected withmetal-to-metal seating in any valve. If the leakage be-comes excessive, however, the condition of the seat-ing surfaces of the valve plug (key 3) and seat ring(key 6) can be improved by lapping. (Deep nicksshould be machined out rather than ground out.) Usea good quality lapping compound with a mixture thatcontains 280 to 600 grit. Apply the compound to thebottom of the valve plug.
Use the following procedure to lap the seating sur-faces. Key numbers referenced in this procedure areshown in figure 14 for the Design EHD valve and infigure 15 for the Design EHT valve.
1. For all designs, install the seat ring gasket or O-ring (key 12), seat ring (key 6), seat ring cap screws(key 7), lower cage gasket (key 12), cage (key 2), andupper cage gasket (key 12) into the valve body per theinstructions in the Trim Replacement procedure.
2. Install the assembled valve plug and stem (keys 3and 4)—without piston rings or seal ring (key 8)—intothe cage.
3. For all seating surfaces, install the bonnet (key 1,figure 13) over the valve stem and secure the bonnetwith four of the hex nuts (key 14).
4. Attach a handle, such as a piece of strap iron se-cured by stem locknuts, to the valve plug stem. Rotatethe handle alternately in each direction to lap theseats.
Note
In order to preserve the effects of lap-ping, do not change either the positionof the seat ring in the valve body cavityor the position of the cage on the seatring after lapping the seating surfaces. Ifpossible, clean the parts without dis-turbing their positions. If the parts mustbe removed for cleaning, return them tothe original positions.
5. After lapping, again disassemble as necessary,clean the seating surfaces, reassemble, and test forshutoff. Repeat the lapping procedure if necessary.
Trim ReplacementAfter all trim maintenance has been completed, reas-semble the valve by following the numbered steps be-low. Be certain that all gasketed surfaces are clean.Key numbers referenced in this procedure are shownin figure 14 for the Design EHD valve and in figure 15for the Design EHT valve.
CAUTION
Thoroughly clean the seat ring (key 6),the seat ring cap screws (key 7), and thecap screw threads in the valve bodywith a good-quality degreaser. Unlessthe valve is to be used for oxygen ser-vice, thoroughly lubricate the cap screwthreads and the underside of the capscrew heads with one of the lubricants(or equivalent) shown in table 7.
Failure to lubricate as described maycause galling and improper seat ringgasket or O-ring (key 12) loading whichmay result in leakage.
WARNING
If the control valve is to be used for oxy-gen service, use the lubrication proce-dure above, but substitute a lubricantthat has been approved for oxygen ser-vice. Use of unapproved lubricantscreates a fire or explosion hazard.
1. Install either the seat ring gasket or the O-ring (key 12). Place the O-ring in the O-ring groove in theseat ring before installing the seat ring in the valve
Design EH (8- through 14-Inch)
11
body. Install the seat ring (key 6) and secure it with theseat ring cap screws (key 7). Torque the hex sockethead cap screws in a criss-cross pattern with no morethan 20 N�m (15 lbf�ft) of torque. When all are tight-ened to 20 N�m (15 lbf�ft), increase the torque 20 N�m(15 lbf�ft) without exceeding the torque value specifiedin table 7, and repeat the crisscross pattern. Repeatuntil all cap screws are tightened to the torque valuespecified in table 7. Repeat the final torque and if anycap screw still turns, tighten every cap screw again.
2. Install one of the cage gaskets (key 11) betweenthe valve body and cage (key 2), and install the cage.
3. If the cage used has multiple sizes of windows, at-tempt to orient the largest window toward the valvebody web (a shelf-like projection of the casting into theflow cavity). As an alternate reference, orient the larg-est window toward the process outlet for a flow-downand toward the process inlet for a flow-up valve.
4. Inspect the valve plug stem threads for any sharpedges that might cut the packing. Use a whetstone oremery cloth to smooth the threads if necessary.
5. To install the piston rings or seal ring (key 8), pro-ceed as appropriate:
For a Design EHD valve, if installing a new pistonring, the replacement piston ring will arrive in onepiece. Use a vise with smooth or taped jaws to breakthis replacement piston ring into halves. Place the newring in the vise so that the jaws compress the ring intoan oval. Slowly compress the ring until the ring snapson both sides. If one side snaps first, do not try to tearor cut the other side. Instead, keep compressing untilthe other side snaps.
Remove any protective tape or covering from thevalve plug and stem assembly, and set it on a protec-tive surface. Then place the piston ring in the pistonring groove with the fractured ends matched.
For a Design EHT valve, install the seal ring (key 8)onto the valve plug (key 3). Install the ring with theopen side facing the seat ring end of the valve plug fora flow-down application (view B of figure 15) or withthe open side facing the valve stem end of the valveplug for a flow-up application. Slide the backup ring(key 9) onto the valve plug. Secure with the retainingring (key 10). For a Design EHT valve with a WhisperTrim Level D cage, install the piston ring (key 30, fig-ure 15) using the procedure given in the Design EHDinstructions immediately preceding this paragraph.
6. Install the valve plug into the cage.
7. Install the other cage gasket (key 11) between thecage and the bonnet.
CAUTION
Failure to comply with good bonnet-to-body bolting practices and the torquevalues shown in table 6 may result incage crushing, cage diameter reduction,and/or bonnet deformation. Cheaterbars or slug wrenches should not beused for this procedure.
Hot torquing is not recommended.
8. Install the bonnet over the valve stem and onto thevalve body. Lubricate the threads of the studs (key 13)and the faces of the hex nuts (key 14) with Never-Seez Pure Nickel Special lubricant or equivalent (key 24). Secure the bonnet with hex nuts (key 14)and washers (key 29). Torque the nuts in a crisscrosspattern to no more than 1/4 of the nominal torque val-ue specified in table 6. When all nuts are tightened tothat torque value, increase the torque by 1/4 of thespecified torque value and repeat the crisscross pat-tern. Repeat this procedure until all nuts are tightenedto the specified nominal value. Repeat the final torquevalue and if any nut still turns, tighten every nut again.
9. Install new packing and the metal packing boxparts according to the appropriate arrangement in figure 6. Slip a smooth-edged pipe over the valvestem, and gently tamp each soft packing part into thepacking box.
10. Slide the packing follower, wiper, and packingflange into position. Lubricate the packing flange studs(key 4) and the faces of the packing flange nuts (key 5) and then install the packing flange nuts.
For spring-loaded PTFE V-ring packing: Tightenthe packing flange nuts until the shoulder on the pack-ing follower (key 13) contacts the bonnet (key 1).
For other kinds of packing, except ENVIRO-SEALand HIGH-SEAL: Tighten the packing flange nuts tothe maximum recommended torque shown in table 5.Then, loosen the packing flange nuts and retightenthem to the recommended minimum torque in table 5.
For ENVIRO-SEAL and HIGH-SEAL packing: Seethe Fisher Controls instruction manuals titledENVIRO-SEAL Packing System for Sliding-StemValves or HIGH-SEAL Live-Loaded Packing System(as appropriate) for packing instructions.
11. Mount the actuator by following the ActuatorMounting procedure. Check for packing leakage as thevalve is being put into service. Retorque the packingflange nuts as required (see table 5). Then, retightenthe hex nuts (key 14) to the torque shown in table 6.
Design EH (8- through 14-Inch)
12
Figure 7. Design EHD with C-seal Trim
FLOW DOWN FLOW UP
���%��
37B1047-A / IL
A
Retrofit: Installing C-seal Trim
Note
Additional actuator thrust is required fora valve with C-seal trim. When installingC-seal trim in an existing valve, contactyour Fisher Controls sales office orsales representative for assistance indetermining new actuator thrust require-ments.
Assemble the new valve plug/retainer assembly (withC-seal plug seal) using the following instructions:
CAUTION
To avoid leakage when the valve is re-turned to service, use appropriate meth-ods and materials to protect all sealingsurfaces of the new trim parts while as-sembling the individual parts and dur-ing installation in the valve body.
1. Apply a suitable high-temperature lubricant to theinside diameter of the C-seal plug seal. Also, lubricatethe outside diameter of the valve plug where theC-seal plug seal must be pressed into the proper seal-ing position (figure 7).
2. Orient the C-seal plug seal for correct sealing ac-tion based on the process fluid flow direction throughthe valve.
� The open interior of the C-seal plug seal mustface up in a valve with flow-up construction (figure 7).
� The open interior of the C-seal plug seal mustface down in a valve with flow-down construction (fig-ure 7).
Note
An installation tool must be used toproperly position the C-seal plug sealon the valve plug. A tool is available asa spare part from Fisher Controls or atool could be manufactured followingthe dimensions given in figure 8.
3. Place the C-seal plug seal over the top of the valveplug and press the C-seal plug seal onto the plug us-ing the C-seal installation tool. Carefully press theC-seal plug seal onto the plug until the installation toolcontacts the horizontal reference surface of the valveplug (figure 10).
4. Apply a suitable high-temperature lubricant to thethreads on the plug. Then, place the C-seal retaineronto the plug and tighten the retainer using an ap-propriate tool such as a strap wrench.
5. Using an appropriate tool such as a center punch,stake the threads on top of the plug in one place (fig-ure 9) to secure the C-seal retainer.
6. Install the new plug/retainer assembly with C-sealplug seal on the new stem following the appropriateinstructions in the Trim Replacement section of thismanual.
7. Install piston rings by following instructions in theTrim Replacement section of this manual.
8. Remove the existing valve actuator and bonnetfollowing the appropriate instructions in the ReplacingPacking section of this manual.
Design EH (8- through 14-Inch)
13
FOR VALVEPLUGSFITTING
DIMENSIONS, INCHES(See Drawing Below)
PARTNUMBER(To OrderFITTING
PORT SIZE(Inches)
A B C D E F G H(To OrderA Tool)
2-7/8 3.25 2.060 - 2.070 0.196 - 0.198 0.146 - 0.148 1.62 2.074 - 2.078 2.170 - 2.190 2.791 - 2.797 24B9816X012
3-7/16 4.00 2.310 - 2.320 0.196 - 0.198 0.146 - 0.148 2.00 2.402 - 2.406 2.498 - 2.518 3.353 - 3.359 24B5612X012
3-5/8 4.11 2.560 - 2.570 0.196 - 0.198 0.146 - 0.148 2.00 2.714 - 2.718 2.810 - 2.830 3.541 - 3.547 24B3630X012
4-3/8 4.96 3.285 - 3.295 0.196 - 0.198 0.146 - 0.148 2.00 3.439 - 3.443 3.535 - 3.555 4.291 - 4.297 24B3635X012
5-3/8 5.62 3.940 - 3.950 0.196 - 0.198 0.146 - 0.148 1.81 4.088 - 4.092 4.184 - 4.204 5.048 - 5.054 23B9193X012
7 7.25 5.566 - 5.576 0.196 - 0.198 0.146 - 0.148 2.37 5.714 - 5.718 5.810 - 5.830 6.674 - 6.680 23B9180X012
8 8.25 6.566 - 6.576 0.196 - 0.198 0.146 - 0.148 2.20 6.714 - 6.718 6.810 - 6.830 7.674 - 7.680 24B9856X012
Figure 8. C-seal Plug Seal Installation Tool
45° X 0.06
∅ A
∅ B
8° - 9°
DC
∅ F
∅ G
∅ H
E
BREAK SHARPCORNER45° X 0.01 MAX
45° X 0.02
A6777 / IL
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
CAUTION
Do not remove the existing valve stemfrom the valve plug unless you are plan-ning to replace the valve stem.
Never reuse an old valve stem with anew plug or reinstall a valve stem after ithas been removed. Replacing a valvestem requires drilling a new pin hole inthe stem. This drilling weakens the stemand may cause failure in service. How-ever, a used valve plug may be reusedwith a new valve stem.
9. Remove the existing valve stem and plug, cage,and seat ring from the valve body following the ap-propriate instructions in the Trim Removal section ofthis manual.
10. Replace all gaskets according to appropriateinstructions in the Trim Replacement section of thismanual.
11. Install the new seat ring, cage, valve plug/retainerassembly, and stem into the valve body and complete-ly reassemble the valve package following the ap-propriate instructions in the Trim Replacement sectionof this manual.
Design EH (8- through 14-Inch)
14
Figure 9. Stake the Threads of the C-seal Retainer
C-SEALMETALPLUGSEAL VALVE
PLUG
��%��%�
PISTONRING
RETAINER
DEFORM THREAD TOSTAKE C-SEAL RETAINER
A6779 / IL
CAUTION
To avoid excessive leakage and seaterosion, the valve plug must be initiallyseated with sufficient force to overcomethe resistance of the C-seal plug sealand contact the seat ring. You can cor-rectly seat the valve plug by using thesame force calculated for full load whensizing your actuator. With no pressuredrop across the valve, this force will ad-equately drive the valve plug to the seatring, thus giving the C-seal plug seal apredetermined permanent set. Once thisis done, the plug/retainer assembly, thecage, and the seat ring become amatched set.
With full actuator force applied and thevalve plug fully seated, align the actua-tor travel indicator scale with the lowerend of valve travel. Refer to the ap-propriate actuator instruction manualfor information on this procedure.
Replacement of Installed C-seal Trim
Trim Removal (C-seal Constructions)1. Remove the valve actuator and bonnet followingthe appropriate instructions in the Replacing Packingsection of this manual.
Figure 10. Installing the C-seal Plug SealUsing the Installation Tool
C-SEALMETALPLUGSEAL
INSTALLATIONTOOL
A6778 / IL
VALVEPLUG
HORIZONTALREFERENCESURFACE
��%��%�
NOTE: PRESS THE INSTALLATION TOOL OVER THE VALVE PLUG UNTIL THETOOL CONTACTS THE HORIZONTAL REFERENCE SURFACE OF THE VALVEPLUG.
CAUTION
To avoid leakage when the valve is re-turned to service, use appropriate meth-ods and materials to protect all sealingsurfaces of the trim parts during mainte-nance.
Use caution when removing pistonring(s) and C-seal plug seal to avoidscratching any sealing surface.
CAUTION
Do not remove the valve stem from theplug/retainer assembly unless you areplanning to replace the valve stem.
Never reuse an old valve stem with anew plug or reinstall a valve stem after ithas been removed. Replacing a valvestem requires drilling a new pin hole inthe stem. This drilling weakens the stemand may cause failure in service. How-ever, a used valve plug may be reusedwith a new valve stem.
2. Remove the plug/retainer assembly (with C-sealplug seal), cage, and seat ring from the valve bodyfollowing the appropriate instructions in the Trim Re-moval section of this manual.
Design EH (8- through 14-Inch)
15
3. Locate the staked thread on top of the valve plug(figure 9). The staked thread secures the retainer. Usea drill with a 1/8-inch bit to drill out the staked area ofthe thread. Drill approximately 1/8-inch into the metalto remove the staking.
4. Locate the break between sections of the pistonring(s). Using an appropriate tool such as a flat-bladescrewdriver, carefully pry out the piston ring(s) fromthe groove(s) in the C-seal retainer.
5. After removing the piston ring(s), locate the0.25-inch diameter hole in the groove. In a retainerwith two piston ring grooves, the hole will be found inthe upper groove.
6. Select an appropriate tool such as a punch andplace the tip of the tool into the hole with the body ofthe tool held tangent to the outside diameter of theretainer. Strike the tool with a hammer to rotate theretainer and free it from the valve plug. Remove theretainer from the plug.
7. Use an appropriate tool such as a flat-blade screw-driver to pry the C-seal plug seal off the plug. Use cau-tion to avoid scratches or other damage to the sealingsurfaces where the C-seal plug seal makes contactwith the valve plug (figure 11).
8. Inspect the lower seating surface where the valveplug contacts the seat ring for wear or damage whichwould prevent proper operation of the valve. Also, in-spect the upper seating surface inside the cage wherethe C-seal plug seal contacts the cage, and inspectthe sealing surface where the C-seal plug seal makescontact with the plug (figure 11).
9. Replace or repair trim parts according to the follow-ing procedure for lapping metal seats, remachiningmetal seats, or other valve plug maintenance proce-dures as appropriate.
Lapping Metal Seats (C-seal Constructions)Before installing a new C-seal plug seal, lap the lowerseating surface (valve plug to seat ring, figure 11) fol-lowing appropriate procedures in the Lapping Seatssection of this manual.
Remachining Metal Seats (C-seal Constructions)See figure 12. A valve plug with a C-seal metal plugseal features two seating surfaces. One seating sur-face is found where the valve plug contacts the seatring. The second seating surface is found where theC-seal plug seal contacts the upper seating surface inthe cage. If you machine the seats on the seat ringand/or plug, you must machine an equal dimensionfrom the seating area in the cage.
Figure 11. Lower (Valve Plug to Seat Ring) and Upper (C-seal Plug Seal to Cage) Seating Surfaces
C-seal METALPLUG SEAL
RETAINER
CAGEVALVE PLUG
NOTE: UPPER SEATING SURFACE IS THE AREA OFCONTACT BETWEEN THE C-seal METAL PLUGSEAL AND THE CAGE.
PLUG
CAGE
SEATRING
������ ������ ��������
�%��������� ��������
A6780 / IL
1
1
CAUTION
If metal is removed from the seat ringand plug and a corresponding amountis not removed from the cage seatingarea, the C-seal plug seal will becrushed as the valve closes and theC-seal retainer will strike the seatingarea of the cage, preventing the valvefrom closing.
Trim Replacement (C-seal Constructions)1. Apply a suitable high-temperature lubricant to theinside diameter of the C-seal plug seal. Also, lubricatethe outside diameter of the valve plug where the C-seal plug seal must be pressed into the proper seal-ing position (figure 7).
2. Orient the C-seal plug seal for correct sealing ac-tion based on the process fluid flow direction throughthe valve.
� The open interior of the C-seal plug seal mustface up in a valve with flow-up construction (figure 7).
Design EH (8- through 14-Inch)
16
Figure 12. Example of Machining the Lower (Valve Plug toSeat Ring) and Upper (C-seal Plug Seal to Cage)
Seating Surfaces
UPPER SEATINGSURFACE
0.020 INCH(4)
0.010 INCH(4)
0.010 INCH(4)
C-sealRETAINER
MACHINING OF THE UPPERSEATING SURFACE MUSTEQUAL THE TOTAL MACHININGOF THE LOWER SEATING SUR-FACE (PLUG PLUS SEAT RING).IF NOT, THE RETAINER MAYSTRIKE THE UPPER SEATINGSURFACE BEFORE THE VALVEPLUG PROPERLY SEATS ONTHE LOWER SEATING SUR-FACE.
�%��������� ��������
REMOVAL OF 0.010 INCH FROM THE VALVE PLUGPLUS REMOVAL OF 0.010 INCH FROM THE SEAT RING
MUST EQUAL REMOVAL OF 0.020 INCH FROM THE UP-PER SEATING SURFACE IN THE CAGE4. THESE VALUES ARE FOR EXAMPLE ONLY. REMOVEONLY THE MINIMUM AMOUNT OF MATERIAL REQUIRED TOREFURBISH THE SEATS.
SEATRING
PLUG
CAGE
A6781 / IL
1
3
2
123
NOTE:
� The open interior of the C-seal plug seal mustface down in a valve with flow-down construction (fig-ure 7).
Note
An installation tool must be used toproperly position the C-seal plug sealon the valve plug. A tool is available asa spare part from Fisher Controls or atool could be manufactured followingthe dimensions given in Figure 8.
3. Place the C-seal plug seal over the top of the valveplug and press it onto the plug using the installationtool. Carefully press the C-seal plug seal onto the pluguntil the installation tool contacts the horizontal refer-ence surface of the valve plug (figure 10).
4. Apply a suitable high-temperature lubricant to thethreads on the plug. Then, place the C-seal retaineronto the plug and tighten the retainer using an ap-propriate tool such as a strap wrench.
5. Using an appropriate tool such as a center punch,stake the threads on top of the plug in one place (fig-ure 9) to secure the C-seal retainer.
6. Replace the piston ring(s) following instructions inthe Trim Replacement section of this manual.
7. Return the seat ring, cage, plug/retainer assembly,and stem to the valve body and completely reas-semble the valve package following the appropriateinstructions in the Trim Replacement section of thismanual.
CAUTION
To avoid excessive leakage and seaterosion, the valve plug must be initiallyseated with sufficient force to overcomethe resistance of the C-seal plug sealand contact the seat ring. You can cor-rectly seat the valve plug by using thesame force calculated for full load whensizing your actuator. With no pressuredrop across the valve, this force will ad-equately drive the valve plug to the seatring, thus giving the C-seal plug seal apredetermined permanent set. Once thisis done, the plug/retainer assembly, thecage, and the seat ring become amatched set.
With full actuator force applied and thevalve plug fully seated, align the actua-tor travel indicator scale with the lowerend of valve travel. Refer to the ap-propriate actuator instruction manualfor information on this procedure.
Actuator MountingThe following procedure assumes that the valve andactuator are fully assembled, but with the actuator re-moved from the valve. Unless otherwise identified, theparts involved in making up the actuator-valve stemconnection are shown in figure 5.
CAUTION
Never use a wrench or pliers on thevalve plug stem and never turn the valveplug stem while the valve plug assemblyis seated. A damaged stem could cut thepacking and allow leakage. Turning theplug while seated could damage theseats allowing leakage at shutoff.
1. Turn the stem locknuts onto the valve stem.
2. Move the valve plug to the closed position.
Design EH (8- through 14-Inch)
17
3. Place the actuator on the bonnet and secure withthe hex nuts (key 26, figure 13). Connect supply pres-sure to the actuator.
4. Make sure the actuator stem is fully retracted. Witha properly assembled direct-acting spring-return ac-tuator, spring compression forces the actuator stem tothe fully retracted position. A double-acting piston ac-tuator or a reverse-acting spring-return actuator re-quires air pressure (or a side-mounted handwheel) tostroke the actuator stem to the fully retracted position.
5. Extend the actuator stem a distance equal to thetravel (as specified on the nameplate).
6. Attach both halves of the stem connector, makingsure the connector fully engages both the actuatorthreads and valve plug stem threads. Install the capscrews in the stem connector, but tighten them onlyslightly at this time.
7. Stroke the valve to the fully open position. Thetravel indicator should show the valve to be wide open.If it does not, loosen the screws that hold the travelindicator scale, and shift the scale to the required posi-tion.
8. Stroke the valve to the closed position. The travelindicator should show the valve to be closed.
9. If travel is not correct, lift the valve plug assembly(key 3, figure 14 or 15) off its seat approximately 6.4
mm (1/4 inch) and screw the valve plug stem into orout of the stem connector as follows. To lengthen trav-el, turn the valve plug stem into the stem connectorslightly. To shorten travel, turn the valve plug stem outof the stem connector slightly. (Turning it out too farwill limit the stroke.)
10. After adjusting the stem connection so that theactuator will properly stroke the valve plug assembly,tighten the cap screws in the stem connector, tighten-ing the one opposite the anti-rotation groove first.Then lock the stem locknuts against the stem connec-tor.
Parts OrderingEach valve is assigned a serial number, which can befound on the valve body. This same number also ap-pears on the actuator nameplate when the valve isshipped from the factory as part of a control valve as-sembly. Refer to the number when contacting yourFisher Controls sales office or sales representative fortechnical assistance or when ordering replacementparts.
When ordering replacement parts, also be sure to in-clude the 11-character part number for each part re-quired from the following parts list.
Parts KitsENVIRO-SEAL Packing Retrofit KitsRetrofit kits include parts to convert existing packing tothe ENVIRO-SEAL packing system. PTFE kits includekeys 200, 201, 211, 212, 214, 215, 217, 218, tag, andcable tie. Graphite kits include keys 200, 201, 207,208, 209, 210, 211, 212, 214, 216, 217, tag, and cable
tie. Duplex kits include keys 200, 201, 207, 209, 211,212, 214, 215, 216, 217, tag, and cable tie. Stems andpacking box constructions that do not meet FisherControls stem finish specifications, dimensional toler-ances, and design specifications, may adversely alterthe performance of the packing kit.
Stem Diametermm (Inches)
Yoke Boss Diametermm (Inches)
KitsPacking Material
mm (Inches) mm (Inches)Double PTFE Single Graphite Duplex
31.8 (1-1/4) 127 (5, 5H) RPACKXRT052 RPACKXRT102 RPACKXRT252
ENVIRO-SEAL Packing Repair KitsRepair kits include parts to replace the ‘‘soft’’ packingmaterials in valves that already have ENVIRO-SEALpacking arrangements installed or in valves that havebeen upgraded with ENVIRO-SEAL retrofit kits. PTFE
repair kits include keys 214, 215, and 218. Graphiterepair kits include keys 207, 208, 209, 210, and 214.Duplex repair kits include keys 207, 209, 214, and215.
Stem Diametermm (Inches)
Yoke Boss Diametermm (Inches)
KitsPacking Material
mm (Inches) mm (Inches)Double PTFE Single Graphite Duplex
31.8 (1-1/4) 127 (5, 5H) RPACKX00232 RPACKX00282 RPACKX00332
Design EH (8- through 14-Inch)
18
Figure 13. Bonnet Assembly35A3976-A / IL
Parts ListKey Description Part Number
Bonnet Assembly (figures 6 and 13)1 Bonnet
If you need a bonnet as a replacement part, order by valve size and stem diameter, serial number, and desired material.
3 Packing Flange 127 mm (5-inch) yoke boss diameter Cd pl steel 0W085625052316 stainless steel 1J100735072B7M steel (for sour gas service) 0W085625052
178 mm (7-inch) yoke boss diameter Steel 1V312928982316 stainless steel 1V3129X0012B7M steel (for sour gas service) 1V312928982
Key Description Part Number4 Packing Flange Stud
127 mm (5-inch) yoke boss diameter (2 req’d) Cd pl steel 0W086931032316 stainless steel 0W086935222B7M steel (for sour gas service) 0W0869X0032
178 mm (7-inch) yoke boss diameter (3 req’d) Cd pl steel 1V313131032316 stainless steel 1V3131X0022B7M steel (for sour gas service) 1V3131X0052
5 Packing Flange Nut 127 mm (5-inch) yoke boss diameter (2 req’d) Cd pl steel 1A368124112316 stainless steel 1A368135252B7M steel (for sour gas service) 1A3681X0042
178 mm (7-inch) yoke boss diameter (3 req’d) Steel 1A440924112316 stainless steel 1A440935252B7M steel (for sour gas service) 1A4409X0042
6* Packing Set See following table7* Packing Ring See following table8 Spring or Lantern Ring See following table9* Packing Ring See following table
10 Washer See following table11* Packing Box Ring See following table12* Upper Wiper, felt See following table13 Packing Follower, 316 stainless
steel See following table14 Pipe Plug (not shown)
Steel 1A7675 24662316 stainless steel 1A767535072
14 Lubricator, steel (not shown) 0V0873000A214 Lubricator/Isolating Valve (not shown) AJ5428000A225 Actuator Mounting Stud, steel
(8 req’d) 1R36903101226 Hex Nut, steel (8 req’d) 1A36812411230* Lower Wiper, PTFE See following table31* Male Adapter, PTFE See following table32* Female Adapter, PTFE/glass See following table
*Recommended spare parts
Design EH (8- through 14-Inch)
19
Keys 6, 7, 9, 12, 30, 31 and 32 Soft Packing Parts*VALVE STEMCONNECTION PACKING
ARRANGEMENTKEY
NUMBERPACKING PARTDESCRIPTION
QUANTITY PARTNUMBER
mm InchesARRANGEMENT NUMBER DESCRIPTION
QUANTITYNUMBER
PTFE, single packing
631327
30
Packing set (includes keys 7, 30, 31 & 32)Male AdapterFemale AdapterV-ringLower Wiper
11131
1R2908010121H9957010121H9958010121D3876010121J872506992
12 Upper Wiper 1 1J873006332
31.8 1-1/4
PTFE, double packing
6
31327
30
Packing set(includes keys 7, 30, 31, & 32)Male AdapterFemale AdapterV-ringLower Wiper
2
2262
1R290801012
1H9957010121H9958010121K3876010121J87250699231.8 1-1/4
12 Upper Wiper 1 1J873006332
Low chloride-graphite laminateand filament, single packing
77
Graphite Filament Packing RingsGraphite Laminate Packing Rings
32
1D7520X01621V5666X0022
Low chloride-graphite laminateand filament, double packing
77
Graphite Filament Packing RingsGraphite Laminate Packing Rings
53
1D7520X01621V5666X0022
Graphite-composition,double packing
77
Packing RingsPacking Rings
23
1D7520010521D751901052
double packing12 Upper Wiper 1 1J873006332
PTFE-composition, 7 Packing Rings 8 1D7520X0012PTFE com osition,double packing 12 Upper Wiper 1 1J873006332
Low chloride-graphite laminateand filament, single packing
79
Graphite Laminate Packing RingsGraphite Filament Packing Rings
34
10A4801X0221N2600X0042
Low chloride-graphite laminateand filament, double packing
79
Graphite Laminate Packing RingsGraphite Filament Packing Rings
34
10A4801X0221N2600X0042
50.8 2 Graphite-composition, 7 Packing Rings 7 1N2600X0032Gra hite com osition,double packing 12 Upper Wiper 1 1V313206332
PTFE-composition, 7 Packing Rings 7 1N260001042PTFE com osition,double packing 12 Upper wiper 1 1V313206332
Keys 8, 10, 11*, and 13 Metal Packing Parts
VALVE STEMCONNECTION PACKING KEY PACKING PART QUANTITY
MATERIALCONNECTION PACKING
TYPEKEY
NUMBERPACKING PARTDESCRIPTION
QUANTITYREQUIRED 316
mm InchesTYPE NUMBER DESCRIPTION REQUIRED 316
Stainless Steel
PTFE, single packing
8101113
SpringWasherPacking box ringPacking follower
1111
1D3874370121H9959360421J8735350721H998435072
31.8 1-1/4Graphite laminateand filament, double packing
81113
Lantern ringPacking box ringPacking followerWarning Tag
2111
0W0871350721J8735350721H99843507211B9513X012
PTFE, PTFE-composition,graphite-composition, graphitelaminate and filament, doublepacking
81113
Lantern ringPacking box ringPacking followerWarning Tag
1111
0W0871350721J8735350721H99843507211B9513X012
50.8 2
Graphite laminate and filament,single packingPTFE-composition, graphite-composition, graphite laminateand filament, doublepacking
81113
Lantern ringPacking box ringPacking followerWarning Tag
1111
1V3133350721V3127350721V31283507211B9513X012
*Recommended spare parts
Design EH (8- through 14-Inch)
20
Key Description Part Number
Valve Assembly (figures 14 and 15)1 Valve Body
If you need a valve body as a replace- ment part, order by valve size, serial number, and desired material.
2* Cage See following table3* Valve Plug See following tables4* Valve Plug Stem See following tables5* Pin, stainless steel
For use with 31.8 mm (1-1/4 inch) valve plug stem 1V334035072
For use with 50.8 mm (2-inch) valve plug stem 15A4000X012
6* Seat Ring See following tables7 Seat Ring Cap Screw See following tables8* Piston Ring, graphite
For all Design EHD valves (3 req’d) except those with Whisper Trim III cages
8 and 10-inch valves Class 1500 1U5069X0012Class 1500 high-temperature 1U5069X0022Class 2500 11A9727X022Class 2500 high-temperature 11A9727X032
12 and 14-inch valves Class 1500 15A3945X012Class 1500 high-temperature 15A3945X022Class 2500 1U5069X0012Class 2500 high-temperature 1U5069X0022
For Design EHD valve with Whisper Trim III cage only (3 req’d for Level A, B or C and 4 req’d for Level D) 8 and 10-inch valves Class 1500 1U5069X0012Class 1500 high-temperature 1U5069X0022Class 2500 11A9727X022Class 2500 high-temperature 11A9727X032
12 and 14-inch valves Class 1500 15A3945X012Class 1500 high-temperature 15A3945X022Class 2500 1U5069X0012Class 2500 high-temperature 1U5069X0022
8* Seal Ring, N10276/PTFE (for use only with Design EHT valve) For valve with other than Whisper Trim III cage 8 and 10-inch valves Class 1500 15A4010X022Class 2500 15A3974X022
12 and 14-inch valves Class 1500 15A3946X022Class 2500 15A4010X022
For valve with Whisper Trim III cage 8 and 10-inch valves Class 1500 15A4010X032Class 2500 15A3974X022
12 and 14-inch valves Class 1500 15A3946X032Class 2500 15A4010X022
Key Description Part Number9* Backup Ring (for use only with Design
EHT valve) For valve with other than Whisper Trim III cage 8 and 10-inch valves Class 1500 316 stainless steel 15A4009X022416 stainless steel 15A4009X012
Class 2500 316 stainless steel 10A5409X022416 stainless steel 10A5409X012
12 and 14-inch valves Class 1500 316 stainless steel 15A3944X022416 stainless steel 15A3944X012
Class 2500 316 stainless steel 15A4009X022416 stainless steel 15A4009X012
For valve with Whisper Trim III cage 8 and 10-inch valves Class 1500 316 stainless steel 19A9136X012Inconel 600 19A9136X02217-4PH stainless steel, H1075 heat-treated 19A9136X032
17-4PH stainless steel, H1150 heat-treated (for sour gas service) 19A9136X042
Class 2500 316 stainless steel 19A9115X012Inconel 600 19A9115X02217-4PH stainless steel, H1075 heat-treated 19A9115X032
17-4PH stainless steel, H1150 heat-treated (for sour gas service) 19A9115X042
12 and 14-inch valves Class 1500 316 stainless steel 19A9165X012Inconel 600 19A9165X02217-4PH stainless steel, H1075 heat-treated 19A9165X032
17-4PH stainless steel, H1150 heat-treated (for sour gas service) 19A9165X042
Class 2500 316 stainless steel 19A9136X012Inconel 600 19A9136X02217-4PH stainless steel, H1075 heat-treated 19A9136X032
17-4PH stainless steel, H1150 heat-treated (for sour gas service) 19A9136X042
10* Retaining Ring, 302 stainless steel (for Design EHT valve only) 8 and 10-inch valves Class 1500 14A4652X012Class 2500 10A5410X012
12 and 14-inch valves Class 1500 15A3933X012Class 2500 14A4652X012
*Recommended spare parts
Design EH (8- through 14-Inch)
21
Figure 14. Design EHD Valve
FLOW DIRECTION FOR ALL TRIMS EXCEPT THOSE WITH WHISPER TRIM III CAGES
O-RINGCONSTRUCTION
GASKETCONSTRUCTION
VIEW A
APPLY LUBRICANT
59A9171-A / IL
������� ���������%�� ���������� �%������������������
������������������� %������� �����������&��&�����������
%������� ������������������
59A9172-AC0632-1 / IL 59A9180-A / IL 59A9182-A / IL
Design EH (8- through 14-Inch)
22
Figure 15. Design EHT Valve
FLOW DIRECTION FOR ALL TRIMS EXCEPT THOSE WITH WHISPER TRIM III CAGES
O-RINGCONSTRUCTION
GASKETCONSTRUCTION
VIEW A
APPLY LUBRICANT
59A9177-A / IL
������� ���������%�� ���������� �%������������������
������������������� %������� �����������&��&�����������
%������� ������������������59A9184-A / IL 59A9186-A / IL
59A9178-AC0633-1 / IL
VIEW B
Design EH (8- through 14-Inch)
23
Key Description Part Number11* Cage Gasket (2 req’d)
For standard service, silver pl Monel8 and 10-inch valves Class 1500 29A9220X012Class 2500 29A9221X012
12 and 14-inch valves Class 1500 29A9222X012Class 2500 29A9223X012
For sour gas service, tin pl Monel 8 and 10-inch valves Class 1500 29A9220X022Class 2500 29A9221X022
12 and 14-inch valves Class 1500 29A9222X022Class 2500 29A9223X022
12* Seat Ring Gasket Spiral wound Inconel 8 and 10-inch valves Class 1500 19A7468X012Class 2500 19A7469X012
12 and 14-inch valves Class 1500 19A7470X012Class 2500 19A7471X012
12* Seat Ring O-Ring 8 and 10-inch valves Class 1500 Nitrile 1D5470X0032Ethylene/propylene 1D5470X0042Fluoroelastomer 1D5470X0012
Class 2500 Nitrile 19A9013X012Ethylene/propylene 19A9013X042Fluoroelastomer 19A9013X032
12 and 14-inch valves Class 1500 Nitrile 19A9014X012Ethylene/propylene 19A9014X042Fluoroelastomer 19A9014X032
Class 2500 Nitrile 1D5470X0032Ethylene/propylene 1D5470X0042Fluoroelastomer 1D5470X0012
13 Bonnet Stud (12 required) See following table14 Hex Nut (12 req’d) See following table15 Flow Arrow, stainless steel
For all valves except those with Whisper Trim III cages 1V106038982For valves with Whisper Trim III cages 1V417038982
16 Drive Screw, stainless steel (2 req’d) 1A368228982
17 Nameplate, stainless steel 8-inch valve 37A7231X012
10-inch valve 37A7232X01212-inch valve 37A7233X01214-inch valve 37A7234X012
18 Drive Screw, stainless steel (6 req’d) 1A368228982
Figure 16. Design EHT Valve UsingPEEK Anti-Extrusion Rings
FLOWUP
FLOWDOWN
A7220 / IL
Key Description Part Number24 Never Seez Nickel Special Lubricant,
(not furnished with valve) 29 Washer (12 req’d) See following table30* Piston Ring, graphite (for Design EHD
valve with Level D Whisper Trim III cage only) 8 and 10-inch valves Class 1500 1U5069X0012Class 2500 11A9727X022
12 and 14-inch valves Class 1500 15A3945X012Class 2500 1U5069X0012
63 Anti-Extrusion Ring8 and 10-inch valvesClass 1500 22B5998X012Class 2500 21B9342X012
12 and 14-inch valvesClass 1500 23B7441X012Class 2500 22B5998X012
C-seal Trim (figure 7)
Note
Consult your Fisher Controls sales representative or sales office for availability.
Key Description Part Number
2* Cage3* Valve Plug/Retainer4* Valve Plug Stem, Nitronic 506* Seat Ring8* Piston Ring, graphite (2 req’d)
64* C-seal, Inconel
*Recommended spare parts*Recommended spare parts
Design EH (8- through 14-Inch)
24
Key 2* Cage for Valve without Whisper Trim III Cage
VALVE VALVEMATERIAL
VALVESIZE
VALVERATING
CAGE CA6NM, Electrolized 316 Stainless SteelSIZE,
INCHESRATING,CLASS
CAGECONSTRUCTION CA6NM To 427�C
(800�F)Above 427�C
(800�F)Electrolized,
for Standard ServiceENC, for SourGas Service
8 10
1500Equal percentageLinearModified equal percentage
49A7423X01239A7420X01249A7423X012
49A7424X01239A7421X01249A7424X012
49A7425X01239A7422X01249A7425X012
49A7424X02239A7421X02249A7424X022
49A9000X01239A9001X01249A9000X012
8, 10
2500Equal percentageLinearModified equal percentage
49A7429X01239A7426X01249A7429X012
49A7430X01239A7427X01249A7430X012
49A7431X01239A7428X01249A7431X012
49A7430X02239A7427X02249A7430X022
49A9002X01239A9003X01249A9002X012
12 14
1500Equal percentageLinearModified equal percentage
39A7435X01239A7432X01239A7435X012
39A7436X01239A7433X01239A7436X012
39A7437X01239A7434X01239A7437X012
39A7436X02239A7433X02239A7436X022
- - -- - -- - -
12, 14
2500Equal percentageLinearModified equal percentage
49A7441X01239A7438X01249A7441X012
49A7442X01239A7439X01249A7442X012
49A7443X01239A7440X01249A7443X012
49A7442X02239A7439X02249A7442X022
- - -- - -- - -
Key 2* Whisper Trim III Cage
VALVESIZE, CAGE
CONSTRUCTION
ELECTROLIZEDJETHETE
17-4PH STAINLESS STEEL WITHH1150 HEAT-TREATMENTFOR SOUR GAS SERVICESIZE,
INCHES CONSTRUCTIONClass
1500 RatingClass
2500 RatingClass
1500 RatingClass
2500 Rating
8, 10
Level A1Level A3Level B1Level B3Level C1Level C3
Level D1(1)
Level D3(1)
30B1118X01230B1120X01230B1122X01230B1124X01230B1126X01230B1128X01230B1185X01230B1185X022
30B1130X01230B1132X01230B1134X01230B1136X01230B1138X01230B1140X01230B1189X01230B1189X022
30B1119X01230B1121X01230B1123X01230B1125X01230B1127X01230B1129X01230B1186X01230B1186X022
30B1131X01230B1133X01230B1135X01230B1137X01230B1139X01230B1141X01230B1190X01230B1190X022
12, 14
Level A1Level A3Level B1Level B3Level C1Level C3
Level D1(1)
Level D3(1)
30B1142X01230B1144X01230B1146X01230B1148X01230B1150X01230B1152X01230B1193X01230B1193X022
30B1154X01230B1156X01230B1158X01230B1160X01230B1162X01230B1164X01230B1197X01230B1197X022
30B1143X01230B1145X01230B1147X01230B1149X01230B1151X01230B1153X01230B1194X01230B1194X022
30B1155X01230B1157X01230B1159X01230B1161X01230B1163X01230B1165X01230B1198X01230B1198X022
1. This part number represents a cage and baffle assembly.
*Recommended spare parts
Design EH (8- through 14-Inch)
25
Key 3* Valve Plug for Valve without Whisper Trim III Cage
VALVE SIZE, VALVE VALVE/PLUG
VALVE STEMCONNECTION
SIZEHEAT TREATED 420STAINLESS STEEL
316 STAINLESS STEEL WITHALLOY 6 (CoCr-A) SEAT AND GUIDE
VALVE SIZE,INCHES
VALVERATING
VALVE/PLUGDESIGN SIZE STAINLESS STEEL
(DESIGN EHD OR EHT)For Use Only with For Service AboveINCHES RATING DESIGN
mm Inches(DESIGN EHD OR EHT)
For Use Only withElectrolized 316
Stainless Steel Cage
For Service Above121�C (250�F)
EHD w/odiverter cone
31.850.8
1-1/42
35A3998X01235A3997X012
35A4001X01235A4003X012
35A4002X01235A4004X012
Class
EHDwith divertercone
50.8 2 - - - 39A9047X012 39A9048X012Class1500 EHT w/o
diverter cone31.850.8
1-1/42
35A3991X01235A3992X012
35A4005X01235A4007X012
35A4006X01235A4008X012
8 10
EHTwith divertercone
50.8 2 - - - 39A9049X012 39A9050X012
8, 10EHD w/odiverter cone
31.850.8
1-1/42
35A3963X01239A7494X012
35A3970X01239A7495X012
35A3971X01239A7496X012
Class
EHDwith divertercone
50.8 2 - - - 39A9043X012 39A9044X012Class2500 EHT w/o
diverter cone31.850.8
1-1/42
35A3962X01239A7497X012
35A3968X01239A7498X012
35A3969X01239A7499X012
EHTwith divertercone
50.8 2 - - - 39A9045X012 39A9046X012
EHD w/odiverter cone
31.850.8
1-1/42
35A3926X01235A3927X012
35A3937X01235A3939X012
35A3938X01235A3940X012
Class1500
EHDwith divertercone
50.8 2 - - - 39A9051X012 39A9052X012
EHT w/odiverter cone
31.850.8
1-1/42
35A3924X01235A3925X012
35A3935X01235A3941X012
35A3936X01235A3942X012
12 14
EHTwith divertercone
50.8 2 - - - 39A9053X012 39A9054X012
12, 14EHD w/odiverter cone
31.850.8
1-1/42
35A3998X01235A3997X012
35A4001X01235A4003X012
35A4002X01235A4004X012
Class2500
EHDwith divertercone
50.8 2 - - - 39A9047X012 39A9048X012
EHT w/odiverter cone
31.850.8
1-1/42
35A3991X01235A3992X012
35A4005X01235A4007X012
35A4006X01235A4008X012
EHTwith divertercone
50.8 2 - - - 39A9049X012 39A9050X012
*Recommended spare parts
Design EH (8- through 14-Inch)
26
Key 3* Valve Plug for 8 or 10 Inch Design EHD with Whisper Trim III Cage
OPERATINGTEMPERATURE
VALVESTEM
VALVE RATING
MATERIALTEMPERATURE
LIMITS
STEMCONNEC-
TIONClass 1500 Class 2500
�C �F mm Inches Level A, B, or C Level D Level A, B, or C Level D
17-4PH stainless steel,29 to 427 20 to 800
31.8 1-1/4 - - - 39A9122X012 - - - 39A9137X01217 4PH stainless steel,H900 heat-treated –29 to 427 –20 to 800
50.8 2 - - - 39A9124X012 - - - 39A9139X012
29 to 149 20 to 30031.8 1-1/4 39A9130X012 39A9126X012 39A9145X012 39A9141X012
–29 to 149 –20 to 30050.8 2 39A9132X012 39A9128X012 39A9147X012 39A9143X012
93 to 204 200 to 40031.8 1-1/4 39A9130X022 39A9126X022 39A9145X022 39A9141X022
93 to 204 200 to 40050.8 2 39A9132X022 39A9128X022 39A9147X022 39A9143X022
149 to 260 300 to 50031.8 1-1/4 39A9130X032 39A9126X032 39A9145X032 39A9141X032
149 to 260 300 to 50050.8 2 39A9132X032 39A9128X032 39A9147X032 39A9143X032
204 to 316 400 to 60031.8 1-1/4 39A9130X042 39A9126X042 39A9145X042 39A9141X042
204 to 316 400 to 60050.8 2 39A9132X042 39A9128X042 39A9147X042 39A9143X042
316 stainless steel, alloy 6 (CoCr-A)260 to 371 500 to 700
31.8 1-1/4 39A9130X052 39A1926X052 39A9145X052 39A9141X052316 stainless steel, alloy 6 (CoCr A)seat and guide 260 to 371 500 to 700
50.8 2 39A9132X052 39A9128X052 39A9147X052 39A9143X052g
316 to 427 600 to 80031.8 1-1/4 39A9130X062 39A9126X062 39A9145X062 39A9141X062
316 to 427 600 to 80050.8 2 39A9132X062 39A9128X062 39A9147X062 39A9143X062
371 to 482 700 to 90031.8 1-1/4 39A9130X072 39A9126X072 39A9145X072 39A9141X072
371 to 482 700 to 90050.8 2 39A9132X072 39A9128X072 39A9147X072 39A9143X072
427 to 538 800 to 100031.8 1-1/4 39A9130X082 39A9126X082 29A9145X082 39A9141X082
427 to 538 800 to 100050.8 2 39A9132X082 39A9128X082 39A9147X082 39A9143X082
482 to 593 900 to 110031.8 1-1/4 39A9130X092 39A9126X092 39A9145X092 39A9141X092
482 to 593 900 to 110050.8 2 39A9132X092 39A9128X092 39A9147X092 39A9143X092
29 to 232 20 to 45031.8 1-1/4 39A9130X102 39A9126X102 39A9145X102 39A9141X102
–29 to 232 –20 to 45050.8 2 39A9132X102 39A1928X102 39A9147X102 39A9143X102
Inconel 600, alloy 6 (CoCr-A) seat233 to 427 451 to 800
31.8 1-1/4 39A9130X112 39A9126X112 39A9145X112 39A9141X112Inconel 600, alloy 6 (CoCr A) seatand guide 233 to 427 451 to 800
50.8 2 39A9132X112 39A9128X112 39A9147X112 39A9143X112g
428 to 593 801 to 110031.8 1-1/4 39A9130X122 39A9126X122 39A9145X122 39A9141X122
428 to 593 801 to 110050.8 2 39A9132X122 39A9128X122 39A9147X122 39A9143X122
17-4 stainless steel, H1150 heat-treated alloy 6 (CoCr A) seat 29 to 427 20 to 800
31.8 1-1/4 39A9130X132 39A9126X132 39A9145X132 39A9141X132treated, alloy 6 (CoCr-A) seatand guide
–29 to 427 –20 to 80050.8 2 39A9132X132 39A9128X132 39A9147X132 39A9143X132
17-4 stainless steel, H1150 heat-treated alloy 6 (CoCr A) seat and 29 to 232 20 to 450
31.8 1-1/4 39A9130X142 39A9126X142 39A9145X142 39A9141X142treated, alloy 6 (CoCr-A) seat andguide, for sour gas service
–29 to 232 –20 to 45050.8 2 39A9132X142 39A9128X142 39A9147X142 39A9143X142
*Recommended spare parts
Design EH (8- through 14-Inch)
27
Key 3* Valve Plug for 12 or 14 Inch Design EHD with Whisper Trim III Cage
OPERATINGTEMPERATURE
VALVESTEM
VALVE RATING
MATERIALTEMPERATURE
LIMITS
STEMCONNEC-
TIONClass 1500 Class 2500
�C �F mm Inches Level A, B, or C Level D Level A, B, or C Level D
17-4PH stainless steel,29 to 427 20 to 800
31.8 1-1/4 - - - 39A9151X012 - - - 39A9122X01217 4PH stainless steel,H900 heat-treated –29 to 427 –20 to 800
50.8 2 - - - 39A9153X012 - - - 39A9124X012
29 to 149 20 to 30031.8 1-1/4 39A9159X012 39A9155X012 39A9130X012 39A9126X012
–29 to 149 –20 to 30050.8 2 39A9161X012 39A9157X012 39A9132X012 39A9128X012
93 to 204 200 to 40031.8 1-1/4 39A9159X022 39A9155X022 39A9130X022 39A9126X022
93 to 204 200 to 40050.8 2 39A9161X022 39A9157X022 39A9132X022 39A9128X022
149 to 260 300 to 50031.8 1-1/4 39A9159X032 39A9155X032 39A9130X032 39A9126X032
149 to 260 300 to 50050.8 2 39A9161X032 39A9157X032 39A9132X032 39A9128X032
204 to 316 400 to 60031.8 1-1/4 39A9159X042 39A9155X042 39A9130X042 39A9126X042
204 to 316 400 to 60050.8 2 39A9161X042 39A9157X042 39A9132X042 39A9128X042
316 stainless steel, alloy 6 (CoCr-A)260 to 371 500 to 700
31.8 1-1/4 39A9159X052 39A1955X052 39A9130X052 39A9126X052316 stainless steel, alloy 6 (CoCr A)seat and guide 260 to 371 500 to 700
50.8 2 39A9161X052 39A9157X052 39A9132X052 39A9128X052g
316 to 427 600 to 80031.8 1-1/4 39A9159X062 39A9155X062 39A9130X062 39A9126X062
316 to 427 600 to 80050.8 2 39A9161X062 39A9157X062 39A9132X062 39A9128X062
371 to 482 700 to 90031.8 1-1/4 39A9159X072 39A9155X072 39A9130X072 39A9126X072
371 to 482 700 to 90050.8 2 39A9161X072 39A9157X072 39A9132X072 39A9128X072
427 to 538 800 to 100031.8 1-1/4 39A9159X082 39A9155X082 29A9130X082 39A9126X082
427 to 538 800 to 100050.8 2 39A9161X082 39A9157X082 39A9132X082 39A9128X082
482 to 593 900 to 110031.8 1-1/4 39A9159X092 39A9155X092 39A9130X092 39A9126X092
482 to 593 900 to 110050.8 2 39A9161X092 39A9157X092 39A9132X092 39A9128X092
29 to 232 20 to 45031.8 1-1/4 39A9159X102 39A9155X102 39A9130X102 39A9126X102
–29 to 232 –20 to 45050.8 2 39A9161X102 39A1957X102 39A9132X102 39A9128X102
Inconel 600, alloy 6 (CoCr-A) seat233 to 427 451 to 800
31.8 1-1/4 39A9159X112 39A9155X112 39A9130X112 39A9126X112Inconel 600, alloy 6 (CoCr A) seatand guide 233 to 427 451 to 800
50.8 2 39A9161X112 39A9157X112 39A9132X112 39A9128X112g
428 to 593 801 to 110031.8 1-1/4 39A9159X122 39A9155X122 39A9130X122 39A9126X122
428 to 593 801 to 110050.8 2 39A9161X122 39A9157X122 39A9132X122 39A9128X122
17-4 stainless steel, H1150 heat-treated alloy 6 (CoCr A) seat 29 to 427 20 to 800
31.8 1-1/4 39A9159X132 39A9155X132 39A9130X132 39A9126X132treated, alloy 6 (CoCr-A) seatand guide
–29 to 427 –20 to 80050.8 2 39A9161X132 39A9157X132 39A9132X132 39A9128X132
17-4 stainless steel, H1150 heat-treated alloy 6 (CoCr A) seat and 29 to 232 20 to 450
31.8 1-1/4 39A9200X012 39A9196X012 39A9130X142 39A9126X142treated, alloy 6 (CoCr-A) seat andguide, for sour gas service
–29 to 232 –20 to 45050.8 2 39A9202X012 39A9198X012 39A9132X142 39A9128X142
*Recommended spare parts
Design EH (8- through 14-Inch)
28
Key 3* Valve Plug for Design EHT with Whisper Trim III Cage
VALVEOPERATING
TEMPERATURE
VALVESTEM
VALVE RATINGVALVESIZE,
INCHESMATERIAL
TEMPERATURELIMITS
STEMCONNEC-
TIONClass 1500 Class 2500
INCHES�C �F mm Inches Level A, B, or C Level D Level A, B, or C Level D
17-4 stainless steel,29 to 232 20 to 450
31.8 1-1/4 - - - 39A9123X012 - - - 39A9138X01217 4 stainless steel,H1075 heat-treated –29 to 232 –20 to 450
50.8 2 - - - 39A9125X012 - - - 39A9140X012
29 to 149 20 to 30031.8 1-1/4 39A9131X012 39A9127X012 39A9146X012 39A9142X012
–29 to 149 –20 to 30050.8 2 39A9133X012 39A9129X012 39A9148X012 39A9144X012
316 stainless steel, alloy 693 to 204 200 to 400
31.8 1-1/4 39A9131X022 39A9127X022 39A9146X022 39A9142X022316 stainless steel, alloy 6(CoCr-A) seat and guide 93 to 204 200 to 400
50.8 2 39A9133X022 39A9129X022 39A9148X022 39A9144X022( ) g
149 to 232 300 to 45031.8 1-1/4 39A9131X032 39A9127X032 39A9146X032 39A9142X032
8 10149 to 232 300 to 450
50.8 2 39A9133X032 39A9129X032 39A9148X032 39A9144X0328, 10
Inconel 600, alloy 6 (CoCr-A)29 to 232 20 to 450
31.8 1-1/4 39A9131X042 39A9127X042 39A9146X042 39A9142X042Inconel 600, alloy 6 (CoCr A)seat and guide –29 to 232 –20 to 450
50.8 2 39A9133X042 39A9129X042 39A9148X042 39A9144X042
17-4 stainless steel, H1150heat treated alloy 6 29 to 232 20 to 450
31.8 1-1/4 39A9131X052 39A9127X052 39A9146X052 39A9142X052heat-treated, alloy 6(CoCr-A) seat and guide
–29 to 232 –20 to 45050.8 2 39A9133X052 39A9129X052 39A9148X052 39A9144X052
17-4 stainless steel, H1150heat-treated, alloy 6
29 to 149 20 to 30031.8 1-1/4 39A9131X062 39A9127X062 39A9146X062 39A9142X062
heat treated, alloy 6(CoCr-A) seat and guide, forsour gas service
–29 to 149 –20 to 30050.8 2 39A9133X062 39A9129X062 39A9148X062 39A9144X062
17-4 stainless steel,29 to 232 20 to 450
31.8 1-1/4 - - - 39A9152X012 - - - 39A9123X01217 4 stainless steel,H900 heat-treated –29 to 232 –20 to 450
50.8 2 - - - 39A9154X012 - - - 39A9125X012
29 to 149 20 to 30031.8 1-1/4 39A9160X012 39A9156X012 39A9131X012 39A9127X012
–29 to 149 –20 to 30050.8 2 39A9162X012 39A9158X012 39A9133X012 39A9129X012
316 stainless steel, alloy 693 to 204 200 to 400
31.8 1-1/4 39A9160X022 39A9156X022 39A9131X022 39A9127X022316 stainless steel, alloy 6(CoCr-A) seat and guide 93 to 204 200 to 400
50.8 2 39A9162X022 39A9158X022 39A9133X022 39A9129X022( ) g
149 to 232 300 to 45031.8 1-1/4 39A9160X032 39A9156X032 39A9131X032 39A9127X032
12 14149 to 232 300 to 450
50.8 2 39A9162X032 39A9158X032 39A9133X032 39A9129X03212, 14
Inconel 600, alloy 6 (CoCr-A)29 to 232 20 to 450
31.8 1-1/4 39A9160X042 39A9156X042 39A9131X042 39A9127X042Inconel 600, alloy 6 (CoCr A)seat and guide –29 to 232 –20 to 450
50.8 2 39A9162X042 39A9158X042 39A9133X042 39A9129X042
17-4 stainless steel, H1150heat treated alloy 6 29 to 232 20 to 450
31.8 1-1/4 39A9160X052 39A9156X052 39A9131X052 39A9127X052heat-treated, alloy 6(CoCr-A) seat and guide
–29 to 232 –20 to 45050.8 2 39A9162X052 39A9158X052 39A9133X052 39A9129X052
17-4 stainless steel, H1150heat-treated, alloy 6
29 to 149 20 to 30031.8 1-1/4 39A9201X012 39A9197X012 39A9131X062 39A9127X062
heat treated, alloy 6(CoCr-A) seat and guide, forsour gas service
–29 to 149 –20 to 30050.8 2 39A9203X012 39A9199X012 39A9133X062 39A9129X062
*Recommended spare parts
Design EH (8- through 14-Inch)
29
Key 4* Valve Plug Stem for 8 or 10 Inch Design EHD or EHT Valve without Whisper Trim III Cage
VALVESTEM TRAVEL
MATERIALVALVE
RATING, VALVEDESIGN
STEMCONNECTION ACTUATOR
GROUP
TRAVEL17-4
Stainless316 Stainless Steel Nitronic 50
RATING,CLASS DESIGN
mm InchesGROUP
mm Inches
StainlessSteel, H1150Heat Treated
Non-electrolized
Electrolized Non-electrolized
Electrolized
31.8 1-1/4
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
11A3430X63211A3430X63211A3430X58211A3430X56211A3430XH62
11A3430X62211A3430X62211A3430X57211A3430X55211A3430X592
15A4075X05215A4075X05215A4075X03215A4075X02215A4075X092
11A3430XG1211A3430XG1211A3430XF7211A3430XF6211A3430XF82
- - -- - -- - -- - -- - -
EHD 31.8x
50.81-1/4 x 2
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
29A5895X12229A5895X12229A5895X09229A5895X08229A5895X102
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
29A5895X27229A5895X27229A5895X24229A5895X23229A5895X252
29A6602X06229A6602X06229A6602X03229A6602X02229A6602X042
1500
50.8 2 408409
8989
3-1/23-1/2
14A1430X44214A1430X432
14A1430X15214A1430X182
15A4076X01215A4076X022
14A1430X34214A1430X332
- - -- - -
1500
31.8 1-1/4
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
11A3430X70211A3430X70211A3430X65211A3430X61211A3430XH72
11A3430X69211A3430X69211A3430X64211A3430X60211A3430X662
- - -- - -- - -- - -- - -
11A3430XG6211A3430XG6211A3430XG2211A3430XF9211A3430XG32
- - -- - -- - -- - -- - -
EHT 31.8x
50.81-1/4 x 2
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
29A5895X17229A5895X17229A5895X13229A5895X11229A5895X152
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
29A5895X43229A5895X43229A5895X28229A5895X26229A5895X412
- - -- - -- - -- - -- - -
50.8 2 408409
8989
3-1/23-1/2
14A1430X45214A1430X322
14A1430X10214A1430X192
- - -- - -
14A1430X37214A1430X362
- - -- - -
EHD
31.8 1-1/4100101100, 101
646476
2-1/22-1/2
3
11A3430X63211A3430X61211A3430X612
11A3430X62211A3430X60211A3430X602
15A4075X05215A4075X04215A4075X042
11A3430XG1211A3430XF9211A3430XF92
- - -- - -- - -
2500
EHD31.8
x50.8
1-1/4 x 2100101100, 101
646476
2-1/22-1/2
3
29A5895X13229A5895X11229A5895X112
- - -- - -- - -
- - -- - -- - -
29A5895X28229A5895X26229A5895X262
29A6602X07229A6602X05229A6602X052
2500
EHT
31.8 1-1/4100101100, 101
646476
2-1/22-1/2
3
11A3430X70211A3430X68211A3430X682
11A3430X69211A3430X67211A3430X672
- - -- - -- - -
11A3430XG6211A3430XG4211A3430XG42
- - -- - -- - -
EHT31.8
x50.8
1-1/4 x 2100101100, 101
646476
2-1/22-1/2
3
29A5895X18229A5895X16229A5895X162
- - -- - -- - -
- - -- - -- - -
29A5895X31229A5895X30229A5895X302
- - -- - -- - -
*Recommended spare parts
Design EH (8- through 14-Inch)
30
Key 4* Valve Plug Stem for 12 or 14 Inch Design EHD or EHT Valve without Whisper Trim III Cage
VALVESTEM TRAVEL
MATERIALVALVE
RATING, VALVEDESIGN
STEMCONNECTION ACTUATOR
GROUP
TRAVEL17-4
Stainless316 Stainless Steel Nitronic 50
RATING,CLASS DESIGN
mm InchesGROUP
mm Inches
StainlessSteel, H1150Heat Treated
Non-electrolized
Electrolized Non-electrolized
Electrolized
31.8 1-1/4
404405, 406407802490
102102102114114
444
4-1/24-1/2
11A3430X68211A3430XH6211A3430X63211A3430XJ1211A3430XJ22
11A3430X67211A3430X59211A3430X62211A3430X72211A3430XH22
15A4075X07215A4075X09215A4075X05215A4075X19215A4075X202
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
1500EHDandEHT
31.8x
50.81-1/4 x 2
404405, 406407802490
102102102114114
444
4-1/24-1/2
29A5895X16229A5895X10229A5895X12229A5895X21229A5895X222
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
29A5895X30229A5895X25229A5895X27229A5895X33229A5895X342
29A6602X09229A6602X04229A6602X06229A6602X10229A6602X112
50.8 2408, 409802490
102114114
44-1/24-1/2
14A1430X46214A1430X48214A1430X512
14A1430X22214A1430X12214A1430X232
15A4076X07215A4076X05215A4076X082
- - -- - -- - -
- - -- - -- - -
31.8 1-1/4
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
11A3430XH9211A3430XH9211A3430XH7211A3430X63211A3430XH82
11A3430X71211A3430X71211A3430X66211A3430X62211A3430X362
15A4075X10215A4075X10215A4075X13215A4075X05215A4075X122
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
EHD 31.8x
50.81-1/4 x 2
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
29A5895X18229A5895X18229A5895X14229A5895X12229A5895X162
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
29A5895X31229A5895X31229A5895X29229A5895X27229A5895X302
29A6602X01229A6602X01229A6602X08229A6602X06229A6602X092
2500
50.8 2408408409
7689
76, 89
33-1/2
3, 3-1/2
14A1430X48214A1430X47214A1430X452
14A1430X12214A1430X11214A1430X102
15A4076X05215A4076X06215A4076X032
- - -- - -- - -
- - -- - -- - -
2500
31.8 1-1/4
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
11A3430XJ1211A3430XJ1211A3430XH9211A3430X70211A3430X242
11A3430X72211A3430X72211A3430X71211A3430X69211A3430X232
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
EHT 31.8x
50.81-1/4 x 2
100, 101404405406407
7689898989
33-1/23-1/23-1/23-1/2
29A5895X21229A5895X21229A5895X19229A5895X17229A5895X202
- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -
29A5895X33229A5895X33229A5895X42229A5895X43229A5895X322
- - -- - -- - -- - -- - -
50.8 2408408409
7689
76, 89
33-1/2
3, 3-1/2
14A1430X50214A1430X49214A1430X482
14A1430X14214A1430X13214A1430X122
- - -- - -- - -
- - -- - -- - -
- - -- - -- - -
*Recommended spare parts
Design EH (8- through 14-Inch)
31
Key 4* Valve Plug Stem for Valve with Whisper Trim III Cage
STEMMATERIAL
ACTUATORGROUP
VALVESIZE,
VALVERATING,
STEMDIAMETER TRAVEL 17-4PH
Stainless316 Stainless Steel Nitronic 50
GROUPSIZE,
INCHESRATING,CLASS
StainlessSteel H1150 Non Non
GROUP INCHES CLASSmm Inches mm Inches
Steel, H1150Heat Treated
Non-Electrolized Electrolized
Non-Electrolized Electrolized
8 10
1500 31.831.8 x 50.8
1-1/41-1/4 x 2
178178
77
13A4764X26229A9092X012
13A4764X272- - -
19A9044X012- - -
13A4764X28229A9092X022
- - -29A9093X012
802
8, 102500 31.8
31.8 x 50.81-1/4
1-1/4 x 2146146
5-3/45-3/4
13A4764X29229A9092X032
13A4764X302- - -
19A9094X022- - -
13A4764X31229A9092X042
- - -29A9093X022
802
12 14
1500 31.831.8 x 50.8
1-1/41-1/4 x 2
184184
7-1/47-1/4
13A4764X32229A9092X052
13A4764X332- - -
13A9094X032- - -
13A4764X34229A9092X062
- - -29A9093X032
12, 142500 31.8
31.8 x 50.81-1/4
1-1/4 x 2178178
77
13A4764X32229A9092X052
13A4764X332- - -
13A9094X032- - -
13A4764X34229A9092X062
- - -29A9093X032
Key 6* Seat Ring and Key 7 Cap Screw for Valve with Gasket Construction and without Whisper Trim III Cage
VALVE MATERIAL VALVEKEY 6
KEY 7 CAP SCREWVALVESIZE,
INCHES Seat Ring Cap Screw
VALVERATING,CLASS
KEY 6SEAT RING Part Number Quantity
Required
17-4PH stainless steel, SA-564, 1500 39A7400X032 19A7492X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A7402X032 19A7493X022
Inconel 718 SB 637 GR 7181500 39A7400X022 19A7492X012
8 10
Inconel 718 SB-637, GR 7182500 39A7402X022 19A7493X012
228, 10316 stainless steel, alloy 6 (CoCr-A) SA-453-660, 1500 39A7401X032 19A7492X032
22316 stainless steel, alloy 6 (CoCr A)seat
SA 453 660,Class A 2500 39A7403X032 19A7493X032
Inconel 600 alloy 6 (CoCr A) seat SB 637 GR 7181500 39A7401X042 19A7492X012
Inconel 600, alloy 6 (CoCr-A) seat SB-637, GR 7182500 39A7403X042 19A7493X012
17-4PH stainless steel, SA-564, 1500 39A7404X032 19A7493X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A7406X032 19A7493X022
Inconel 718 SB 637 GR 7181500 39A7404X022 19A7493X012
12, 14 Inconel 718 SB-637, GR 7182500 39A7406X022 19A7493X012 28
316 stainless steel, alloy 6 (CoCr-A) SA-453-660, 1500 39A7405X032 19A7493X032316 stainless steel, alloy 6 (CoCr A)seat
SA 453 660,Class A 2500 39A7407X032 19A7493X032
Inconel 600 alloy 6 (CoCr A) seat SB 637 GR 7181500 39A7405X042 19A7493X012
Inconel 600, alloy 6 (CoCr-A) seat SB-637, GR 7182500 39A7407X042 19A7493X012
*Recommended spare parts
Design EH (8- through 14-Inch)
32
Key 6* Seat Ring and Key 7 Cap Screw for Valve with Gasket Construction and Whisper Trim III Cage
VALVE MATERIAL VALVEKEY 6
KEY 7 CAP SCREWVALVESIZE,
MATERIAL VALVERATING, KEY 6
Q antitySIZE,INCHES Seat Ring Cap Screw
RATING,CLASS
KEY 6SEAT RING Part Number
QuantityRequired
17-4PH stainless steel, SA-564, 1500 39A7400X032 19A7492X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A7402X032 19A7493X022
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A7401X122 19A7492X022H1150 heat treated,alloy 6 (CoCr-A) seat
SA 564,H1100 heat-treated 2500 39A7403X122 19A7493X022
316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A7401X032 19A7492X032(CoCr-A) seat, fortemperatures up to 260�C (500�F)
SA 453 660,Class A 2500 39A7403X032 19A7493X032
316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A7401X062 19A7492X032
8 10
(CoCr-A) seat, fortemperatures up to 427�C (800�F)
SA 453 660,Class A 2500 39A7403X062 19A7493X032
228, 10316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A7401X082 19A7492X032
22
(CoCr-A) seat, fortemperatures up to 593�C (1100�F)
SA 453 660,Class A 2500 39A7403X082 19A7493X032
Inconel 600, alloy 6(CoCr-A) seat for SB 637 GR 718
1500 39A7401X042 19A7492X012(CoCr-A) seat, fortemperatures up to 427�C (800�F)
SB-637, GR 7182500 39A7403X042 19A7493X012
Inconel 600, alloy 6(CoCr-A) seat for SB 637 GR 718
1500 39A7401X102 19A7492X012(CoCr-A) seat, fortemperatures up to 593�C (1100�F)
SB-637, GR 7182500 39A7403X102 19A7493X012
Inconel 718 heat treated SB 637 GR 7181500 39A7400X022 19A7492X012
Inconel 718, heat-treated SB-637, GR 7182500 39A7402X022 19A7493X012
17-4PH stainless steel, SA-564, 1500 39A9009X022 19A7493X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A7406X032 19A7493X022
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A9010X122 19A7493X022H1150 heat treated,alloy 6 (CoCr-A) seat
SA 564,H1100 heat-treated 2500 39A7407X122 19A7493X022
316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A9010X022 19A7493X032(CoCr-A) seat, fortemperatures up to 260�C (500�F)
SA 453 660,Class A 2500 39A7407X032 19A7493X032
316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A9010X042 19A7493X032
12 14
(CoCr-A) seat, fortemperatures up to 427�C (800�F)
SA 453 660,Class A 2500 39A7407X062 19A7493X032
2812, 14316 stainless steel, alloy 6(CoCr-A) seat for SA-453-660, 1500 39A9010X062 19A7493X032
28
(CoCr-A) seat, fortemperatures up to 593�C (1100�F)
SA 453 660,Class A 2500 39A7407X082 19A7493X032
Inconel 600, alloy 6(CoCr-A) seat for SB 637 GR 718
1500 39A9010X082 19A7493X012(CoCr-A) seat, fortemperatures up to 427�C (800�F)
SB-637, GR 7182500 39A7407X042 19A7493X012
Inconel 600, alloy 6(CoCr-A) seat for SB 637 GR 718
1500 39A9010X102 19A7493X012(CoCr-A) seat, fortemperatures up to 593�C (1100�F)
SB-637, GR 7182500 39A7407X102 19A7493X012
Inconel 718 heat treated SB 637 GR 7181500 39A9009X032 19A7493X012
Inconel 718, heat-treated SB-637, GR 7182500 39A7406X022 19A7493X012
*Recommended spare parts
Design EH (8- through 14-Inch)
33
Key 6* Seat Ring and Key 7 Cap Screw for Valve with O-Ring Construction and without Whisper Trim III Cage
VALVE MATERIAL VALVEKEY 6
KEY 7 CAP SCREWVALVESIZE,
INCHES Seat Ring Cap Screw
VALVERATING,CLASS
KEY 6SEAT RING Part Number Quantity
Required
17-4PH stainless steel, SA-564, 1500 39A9035X022 19A7492X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A9037X022 19A7493X022
316 stainless steel, alloy 6 (CoCr-A) SA-453-660, 1500 39A9036X022 19A7492X032316 stainless steel, alloy 6 (CoCr A)seat
SA 453 660,Class A 2500 39A9038X022 19A7493X032
8 10Inconel 600,
SB 637 GR 7181500 39A9036X042 19A7492X012
108, 10Inconel 600,alloy 6 (CoCr-A) seat SB-637, GR 718
2500 39A9038X042 19A7493X01210
17-4PH stainless steel, H1150 heat- SA-564, 1500 39A9035X042 19A7492X04217 4PH stainless steel, H1150 heattreated for sour gas service
SA 564,H1150 heat-treated 2500 39A9037X042 19A7493X042
Inconel 600, alloy 6 (CoCr-A) seat,SB 637 GR 718
1500 39A9036X042 19A7492X052Inconel 600, alloy 6 (CoCr A) seat,for sour gas service SB-637, GR 718
2500 39A9038X042 19A7493X052
17-4PH stainless steel, SA-564, 1500 39A9039X022 19A7493X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1100 heat-treated 2500 39A9041X022 19A7493X022
12 14316 stainless steel, alloy 6 (CoCr-A) SA-453-660, 1500 39A9040X022 19A7493X032
1212, 14316 stainless steel, alloy 6 (CoCr A)seat
SA 453 660,Class A 2500 39A9042X022 19A7493X032
12
Inconel 600,SB 637 GR 718
1500 39A9040X042 19A7493X012Inconel 600,alloy 6 (CoCr-A) seat SB-637, GR 718
2500 39A9042X042 19A7493X012
*Recommended spare parts
Design EH (8- through 14-Inch)
34
Key 6* Seat Ring and Key 7 Cap Screw for Valve with O-Ring Construction and Whisper Trim III Cage
VALVE MATERIAL VALVEKEY 6
KEY 7 CAP SCREWVALVESIZE,
MATERIAL VALVERATING, KEY 6
Q antitySIZE,INCHES Seat Ring Cap Screw
RATING,CLASS
KEY 6SEAT RING Part Number
QuantityRequired
17-4PH stainless steel, SA-564, 1500 39A9035X022 19A7492X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1150 heat-treated 2500 39A9037X022 19A7493X022
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A9036X062 19A7492X022H1150 heat-treatedalloy 6 (CoCr-A) seat
SA 564,H1100 heat-treated 2500 39A9038X062 19A7493X022
Inconel 600,SB 637 GR 718
1500 39A9036X042 19A7492X012Inconel 600,alloy 6 (CoCr-A) seat SB-637, GR 718
2500 39A9038X042 19A7493X012
316 stainless steel, SA-453-660, 1500 39A9036X022 19A7492X0328, 10
316 stainless steel,alloy 6 (CoCr-A) seat
SA 453 660,Class A 2500 39A9038X022 19A7493X032 10
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A9035X042 19A7492X042H1150 heat-treated,for sour gas service
SA 564,H1150 heat-treated 2500 39A9037X042 19A7493X042
17-4PH stainless steel, H1150heat treated alloy 6 (CoCr A) seat
SA-564, 1500 39A9036X072 19A7492X042heat-treated, alloy 6 (CoCr-A) seat,for sour gas service
SA 564,H1150 heat-treated 2500 39A9038X072 19A7493X042
Inconel 600, alloy 6 (CoCr-A) seat,SB 637 GR 718
1500 39A9036X042 19A7492X052Inconel 600, alloy 6 (CoCr A) seat,for sour gas service SB-637, GR 718
2500 39A9038X042 19A7493X052
17-4PH stainless steel, SA-564, 1500 39A9011X022 19A7493X02217 4PH stainless steel,H1075 heat-treated
SA 564,H1150 heat-treated 2500 39A9041X022 19A7493X022
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A9012X062 19A7493X022H1150 heat-treatedalloy 6 (CoCr-A) seat
SA 564,H1100 heat-treated 2500 39A9042X062 19A7493X022
Inconel 600,SB 637 GR 718
1500 39A9012X042 19A7493X012Inconel 600,alloy 6 (CoCr-A) seat SB-637, GR 718
2500 39A9042X042 19A7493X012
316 stainless steel, SA-453-660, 1500 39A9012X022 19A7493X03212, 14
316 stainless steel,alloy 6 (CoCr-A) seat
SA 453 660,Class A 2500 39A9042X022 19A7493X032 12
17-4PH stainless steel,H1150 heat treated
SA-564, 1500 39A9011X042 19A7493X042H1150 heat-treated,for sour gas service
SA 564,H1150 heat-treated 2500 39A9041X042 19A7493X042
17-4PH stainless steel, H1150heat treated alloy 6 (CoCr A)
SA-564, 1500 39A9012X072 19A7493X042heat-treated, alloy 6 (CoCr-A)seat, for sour gas service
SA 564,H1150 heat-treated 2500 39A9042X072 19A7493X042
Inconel 600, alloy 6 (CoCr-A) seat,SB 637 GR 718
1500 39A9012X042 19A7493X052Inconel 600, alloy 6 (CoCr A) seat,for sour gas service SB-637, GR 718
2500 39A9042X042 19A7493X052
*Recommended spare parts
Design EH (8- through 14-Inch)
35
Key 13 Bonnet Stud, Key 14 Hex Nut, and Key 29 Washer
VALVESIZE
MATERIAL VALVERATING
KEY 13STUD
KEY 14HEX NUT
KEY 29WASHERSIZE,
INCHES Stud Hex Nut WasherRATING,CLASS
STUD(12 REQUIRED)
HEX NUT(12 REQUIRED)
WASHER(12 REQUIRED)
SA 193 B7 SA 194 2H Hardened steel1500 15A3906X012 1N850524072 18A6429X032
SA-193-B7 SA-194-2H Hardened steel2500 15A3967X012 10A8500X032 18A8864X012
SA 193 B7 SA 194 7 Hardened steel1500 15A3906X012 1N8505X0022 18A6429X032
SA-193-B7 SA-194-7 Hardened steel2500 15A3967X012 10A8500K012 18A8864X012
SA 193 B16 SA 194 7 Hardened steel1500 15A3906X022 1N8505X0022 18A6429X032
SA-193-B16 SA-194-7 Hardened steel2500 15A3967X022 10A8500K012 18A8864X012
SA 193 B8M SA 194 8M416 stainless steel, 1500 15A3906X032 1N8505X0062 18A6429X022
SA-193-B8M SA-194-8M416 stainless steel,heat-treated 2500 15A3967X032 10A8500X042 18A8864X022
8 10 SA 320 B8 SA 194 8416 stainless steel, 1500 15A3906X042 1N8505X0032 18A6429X022
8, 10 SA-320-B8 SA-194-8416 stainless steel,heat-treated 2500 15A3967X042 10A8500X052 18A8864X022
SA-193-B8M,SA 194 8M
416 stainless steel, 1500 15A3906X092 1N8505X0062 18A6429X022SA 193 B8M,strain-hardened SA-194-8M
416 stainless steel,heat-treated 2500 15A3967X072 10A8500X042 18A8864X022
SA-193-B8M,SA 194 8M
416 stainless steel, 1500 15A3906X062 1N8505X0062 18A6429X022SA 193 B8M,electrolized SA-194-8M
416 stainless steel,heat-treated 2500 15A3967X062 10A8500X042 18A8864X022
SA-193-B7M, SA-194-2HM, 416 stainless steel, 1500 15A3906X052 1N8505X0042 18A6429X022SA 193 B7M,for sour gas service
SA 194 2HM,for sour gas service
416 stainless steel,heat-treated 2500 15A3967X052 10A8500X062 18A8864X022
SA 453 660 SA 194 7 Hardened steel1500 15A3906X072 1N8505X0022 18A6429X032
SA-453-660 SA-194-7 Hardened steel2500 15A3967X082 10A8500K012 18A8864X012
SA 193 B7 SA 194 2H Hardened steel1500 15A3934X012 1P3683X00B2 19A1043X012
SA-193-B7 SA-194-2H Hardened steel2500 15A3999X012 1P389424072 19A1042X012
SA 193 B7 SA 194 7 Hardened steel1500 15A3934X012 1P3683X0022 19A1043X012
SA-193-B7 SA-194-7 Hardened steel2500 15A3999X012 1P3894X00A2 19A1042X012
SA 193 B16 SA 194 7 Hardened steel1500 15A3934X022 1P3683X0022 19A1043X012
SA-193-B16 SA-194-7 Hardened steel2500 15A3999X022 1P3894X00A2 19A1042X012
SA 193 B8M SA 194 8M416 stainless steel, 1500 15A3934X032 1P3683X0032 19A1043X022
SA-193-B8M SA-194-8M416 stainless steel,heat-treated 2500 15A3999X032 1P3894X0032 19A1042X022
12 14 SA 320 B8 SA 194 8416 stainless steel, 1500 15A3934X042 1P3683X0042 19A1043X022
12, 14 SA-320-B8 SA-194-8416 stainless steel,heat-treated 2500 15A3999X042 1P3894X0052 19A1042X022
SA-193-B8M,SA 194 8M
416 stainless steel, 1500 15A3934X092 1P3683X0032 19A1043X022SA 193 B8M,strain-hardened SA-194-8M
416 stainless steel,heat-treated 2500 15A3999X092 1P3894X0032 19A1042X022
SA-193-B8M,SA 194 8M
416 stainless steel, 1500 15A3934X062 1P3683X0032 19A1043X022SA 193 B8M,electrolized SA-194-8M
416 stainless steel,heat-treated 2500 15A3999X062 1P3894X0032 19A1042X022
SA-193-B7M,( )
SA-194-2HM,( )
416 stainless steel, 1500 15A3934X052 1P3683X0052 19A1043X022SA 193 B7M,for sour gas service(1)
SA 194 2HM,for sour gas service(1)
416 stainless steel,heat-treated 2500 15A3999X052 1P3894X0062 19A1042X022
SA 453 660 SA 194 7 Hardened steel1500 15A3934X102 1P3683X0022 19A1043X012
SA-453-660 SA-194-7 Hardened steel2500 15A3999X072 1P3894X00A2 19A1042X012
1. These parts used only with valves containing Whisper Trim III cage.
Design EH (8- through 14-Inch)
36
Actuator Groups by Type Number
Group 100127 mm (5-Inch) Yoke Boss
Group 406127 mm (5-Inch) Yoke Boss
350470
667 MO667-4 MO
471472473
Group 407127 mm (5-Inch) Yoke Boss
473474475476657
1008
4704714744756571008
Group 408Group 408127 mm (5H) and 178 mm (7-Inch) Yoke Boss
657 Size 100Group 101
657 Size 1001008Group 101
127 mm (5-Inch) Yoke Boss1008
127 mm (5-Inch) Yoke BossGroup 409
667Group 409
127 mm (5H) and 178 mm (7 Inch) Yoke Boss667 127 mm (5H) and 178 mm (7-Inch) Yoke Boss667 Size 100
Group 404127 mm (5 Inch) Yoke Boss
667 Size 100
127 mm (5-Inch) Yoke Boss Group 802127 (5 I h) Y k B667
p127 mm (5-Inch) Yoke Boss667
667-4
Group 405127 mm (5-Inch) Yoke Boss
470-16475-16
657 MO657-4 MO
For information, contact Fisher:Marshalltown, Iowa 50158 USACernay 68700 France Sao Paulo 05424 BrazilSingapore 128461
������������������� ���������������������������������������� �������������������������������������������������� ������������ ������������������������������ ������������������� ��������������
������������������������������ �������������������������������������� ��������������������������������������������������������������������������������������� ������� �������������������� ���������
Printed in U.S.A.
�Fisher Controls International, Inc. 1979, 1999; All Rights Reserved
ENVIRO-SEAL, HIGH-SEAL, Cavitrol, Whisper Trim, Fisher and Fisher-Rosemount are marks owned by Fisher Controls International, Inc. or Fisher-Rosemount Systems, Inc. C-seal is amark owned by Pressure Science, Inc. All other marks are the property of their respective owners.This product may be covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or under pending patents.
top related