falcon fairlane
Post on 16-Oct-2021
4 Views
Preview:
TRANSCRIPT
FALCON FAIRLANE w~:~~~~P
LIGHTING GROUP
15
PAGE
PART 15-1- General Lighting System, Horns and Instruments Service 15-2
PART 15-2- Lighting System and Horns 15-7
PART 15-3- Switches, Circuit Breakers and Fuses 15-13
PART 15-4- Instruments - 15-15
PART 15-5- Specifications 15-23
15-2
PART 15-1
GENERAL LIGHTING SYSTEM, HORNS AND INSTRUMENT SERVICE
Section Page
1 Diagnosis and Testing 15-2 Fuel Guage and Fuel Level Sending Unit Test 15-5 Light Trouble Diagnosis Guicle 15-2 Temperature Guag-e Test 15·5 Instrument Trouble Diagnosis Guide 15-2 Oil Pressure Indicator Light Test 15-5 Horn Trouble Diagnosis Guide 15-3 Charge Indicator Light Test 15-5 Turn Indicator Trouble Diag-nosis Guide 15-3 Speedometer Tests 15-5 Windshield Wiper Trouble Diagnosis Guide 15-3 Headlight Switch and Beam Selector Switch
2 Common Adjustments and Repairs 15·6 Horn Adjustment 15-6
Test 15-5 Constant Voltage Regulator Test 15-5
D DIAGNOSIS AND TESTING LIGHT TROUBLE DIAGNOSIS GUIDE
1. Loose battery cable. 2. Loose quick disconnect or bro-
ken w1re from the battery to the ALL HEADLIGHTS DO headlight switch. NOT LIGHT 3. Defective headlight switch.
4. Disconnected or broken wire from the headlight switch to the beam selector switch.
INDIVIDUAL LIGHTS 1. Burned out bulb.
DO NOT LIGHT 2. Loose or broken wires to the
bulb.
LIGHTS BURN OUT 1. Loose or corroded electrical
REPEATEDLY connections.
2. Excessive vibration .
INSTRUMENT TROUBLE DIAGNOSIS GUIDE
OIL PRESSURE INDICATOR 1. Indicator bulb burned out.
LIGHT INOPERATIVE 2. Loose or broken wire from the
light to the indicator switch.
CHARGE INDICATOR 1. Burned out bulb. LIGHT INOPERATIVE
CHARGE INDICATOR I. Faulty alternator and/or reg-LIGHT STAYS ON AT ulator. IDLE
1. Loose terminal s on fuel gauge .
FUEL GAUGE ERRATIC OR INOPERATIVE 2. Defective fuel gauge.
3. Loose, broken, or shorted wire from fuel gauge to the fuel tank sending unit.
5. Loose or broken wire to the bulbs.
6. Defective beam selector switch. 7. All headlight bulbs burned out.
This may be caused by a defective or improperly adjusted alternator voltage regulator (Group 13).
3. Poor ground.
3. Improperly adjusted or defec-tive alternator voltage regulator (Group 13).
3. Defective oil pressure sender unit (in this part).
2. Loose or broken wires.
2. Loose fan belt.
4. Defective constant voltage reg-ulator.
5. Defective fuel tank sending unit.
6. Poor ground between fuel tank and body.
CONTINUED ON NEXT PAGE
PART 15-1- GENERAL LIGHTING SYSTEM, HORNS INSTRUMENTS SERVICE 15-3
INSTRUMENT TROUBLE DIAGNOSIS GUIDE
1. Loose terminals on temp gauge .
TEMPERATURE GAUGE ERRATIC OR INOPERATIVE l. Defective temperature gauge.
3. Loose or broken wire from the temperature sending unit to the tern-
1. Loose or corroded constant FUEL, TEMPERA JURE, AND voltage regulator ground. OIL PRESSURE GAUGES l. Defective constant voltage reg-ERRATIC ulator.
HORN TROUBLE DIAGNOSIS GUIDE
1. Loose connections at horn but-ton· con tact.
HORNS DO NOT SOUND 2. Open wire (blue/red) from horn to horn button .
3. Open wire (green) from fuse
ONE HORN FAILS 1. Broken or loose wire to the TO OPERATE horn (blue/red).
HORNS OPERATE 1. Horn button defective. CONTINUOUSLY
TURN INDICATOR TROUBLE DIAGNOSIS GUIDE
1. Burned out bulbs, or loose
TURN INDICATOR LIGHTS sockets.
INOPERATIVE l. Loose or broken wire from
ignition switch to flasher. 3. Defective flasher.
1. Burned out bulb. TURN INDICATOR LIGHTS l. Loose, broken, or shorted wires OPERATE INCORRECTLY from switch to lights.
TURN INDICATOR 1. Cam improperly positioned on CANCELS IMPROPERLY steering wheel hub.
WINDSHIELD WIPER TROUBLE DIAGNOSIS GUIDE
INOPERATIVE OR SLOW WIPER
1. Binding linkage. 2. Defective switch. 3. Defective wiper motor
perature gauge. 4. Defective temperature sending
unit. 5. Defective constant voltage reg-
ulator.
3 Broken or loose conductor from or to the constant voltage regulator.
4. Defective ignition switch.
box to horn button. 4. Horns defective or out of ad-
justment.
5. Fuse burned out.
l. Horn defective or out of ad-justment.
4. Loose or br0ken wire from flasher to turn indicator switch.
S. Defective turn indicator switch. 6. Broken, shorted, or loose wires
from switch to lights.
3. Defective indicator switch. 4. Defective flasher.
l. Coil spring on switch plate as-sembly loose or weak.
4. Defective wiring or blown fuse.
15-4- GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
-y
FIG. 1 -Installation Speedo Cable.
SPEEDOMETER DIAGNOSTIC PROCEDURES
' '
Speedometer system complaints are generally the result of a visible or audible defect in the sntem. It is imperative that the specific defect be determined prior to attempting any physical repairs to preclude unnecessarily disassembling system components. The following suggestions are intended to aid in quick and accurate system problem diagnosis.
VISIBLE DEFECTS
Sllt~ht Needle Waver or Ievere Needle Fluctuation (No Noise)
1. Loose cable retainer l. Defective speedometer head. 3. Bent cable core at attaching
nut. 4. Kinked or pinched cable hous
ina. S. Excessive grease in speedome-
ter head. Inoperative
1. Broken cable core. l. Defective drive and/ or driven
gear 3. Defective speedometer head .
AUDIBLE DEFECTS
Clicking or Ticking (With Needle Waver), Grinding or Ringing
------------ \ \ ' \ \' ,\ \
\
I . Loose cable retainer. 2. Defective drive and/ or driven
gear. 3. Defective speedometer head. 4. No lube on cable.
SPEEDOMETER REPAIR PROCEDURES NOTE: To effect any tests or repairs on the speedometer head the instrument cluster must be detached from the instrument panel (see page 15 ·15) to gain access.
DEFECTIVE SPEEDOMETER HEAD
Before removing a speedometer head, disconnect the cable at the head and insert a short section of cable core in the head . Rotate the section of core to check for any dragging or noise . The speedometer shaft should turn freely aod evenly.
DEFECTIVE CABLE CORE AND HOUSING
1. To check for a kinked cable core remove and wipe dry. Lay the core out straight on a flat surface and roll it back and forth . Any kinks or damage will be seen . Then take an end in each hand, allowing core to hang in approximately a 230 mm (9 inch) loop. Rotate both ends to be sure core turns evenly.
2. Routing of the cable housjng is particularly important where
@ @ 203414-.3>345 -eat.-T >f- - 20
(f>j ~o -~ - ~,.f€fil
the cable leaves the speedometer head. The optimum routing would provide that the cable and housing take virtually no change of direction for at least a length of 200 mm (8 inches) from the speedometer head.
3. When installing a new cable and housing it is necessary that the new assembly be guided and routed properly to eliminate any kinks.
4. Proper lubrication of the cable core is accomplished by a light application of a lubricant after the cable has been wiped clean. A light film is all that is required.
DEFECTIVE DRIVE AND DRIVEN GEARS
1. A score nicked or gouged driv~ en gear is usually indicative of a defective drive gear on those vehicles that have the drive gear integral with the transmission output shaft . The output shaft should be carcf ully inspected for imperfections aod rep!aced if necessary.
2. A driven gear with two or three adjoining teeth badly scored is indicative of improper assembly procedure. The gear should be inserted in the transmission while simultaneously turning the drive shaft. This will insu re initial gear engagement and prevent gear damage. Force should never be used .
3. Whenever a drive gear is replaced, a new driven gear should al -
PART 15-1- GENERAL LIGHTING SYSTEM, HORNS INSTRUMENTS SERVICE 15-5
so be installed, regardless of its apparent condition.
TESTING Refer to Group 22 for schemat
ics and locations of wiring harnesses.
HORN TEST
The only test necessary on the horn is for current draw.
Current Draw Test
Connect a voltmeter and ammeter to the horn and to a voltage supply as shown in Fig. 2. The normal current draw for the horns at 12 volts is 4-5 amperes.
FIG. 2 -Horn Current Draw Test
HEADLIGHT SWITCH AND BEAM SELECTOR SWITCH TESTS
The following tests may be made to determine whether a headlight ~w1tch or a beam selector sw1tch is defective:
Turn on the headlights, and operate the beam selector switch. If none of the headlights turn on when the beam selector switch is operated, yet the instrument panel lights operate, the headlight switch or the red-yellow stripe wire from the headlight switch to the beam control ~witch is probably defective. Suhstitute a known good switch for the suspected switch to determine whether the switch or the wiring is at fault.
If the headlights operate only with the beam selector switch in one position, the selector switch or the wiring from the switch to the headlight is defective . Substitute a known good selector switch for the suspected switch to determine whefher the switch or the wiring is at fault.
CONSTANT VOLTAGE REGULATOR TEST
The instrument cluster must be re moved to gain access to the voltage regulator and gauge terminals .
Turn the ignition switch on, check for voltage at the fuel gauge upper terminal (Falcon) temp gauge terminal adjacent to the regulator screw . The voltage should oscillate between zero and about I 0
volts. If it does not, the constant voltage regulator is defective, or there is a short to ground between the voltage regulator and the gauges.
If a gauge unit is inaccurate or does not indicate, replace it with a new unit. If the gauge unit still is erratic in its operation, the sending unit or wiring to the sending unit is faulty.
H both the fuel gauge and the temperature gauge indicate improperly and in the same direcdon, the constant voltage regulator could be defecthe, as it supplies both gauges. TESTING FUEL AND
TEMPERATURE GAUGES
FUEL GAUGE.
A simple check to show whether it is the sender unit or gauge unit at fault is to fit a known good sender unit in the circuit.
If the gauge unit reads proportionate to the float setting, the gauge unit is correct.
Do not test gauge units by shorting terminals direct to earth. Minimum circuit resistance is to be held to 10 ohms for high indication. Lower resistances will destroy calibration.
TEMPERATURE GAUGE TEST
Start the engine and allow it to run at 1200 rpm for 30 minutes. Place a thermometer in the coolant at the radiator filler cap. The temperature should read a minimum of 82.2°C ( 180°F), and the gauge in the instrument panel should indicate within the normal band.
If the gauge does not indicate, short the temperature sender unit terminal wire to ground (ignition switch on). Do not leave the sender wire grounded longer than necessary to make the test, as the gauge may be damaged. If the gauge now indicates, the sender unit is defective or not properly sealed to the engine. Be sure to use an electricaUy conductive sealer. If the gauge does not indicate, the gauge, the wires leading to the gauge, or the constant voltage regulator are at fault.
OIL PRESSURE INDICATOR LIGHT TEST
To test the indicator light . turn on the ·ignition switch. Do not start the engine. The light should come on. Start the engine. The light ~hould go
out, indicating that the oil pressure has built up a safe value.
To test the oil pressure switch on the engine. turn the ignition switch on, engine not running, the indicator hgnt snould come on. If the indicator light does not come on, shffi"t the terminal of the oil pressure switch unit to ground. If the light now comes on, the oil pressure switch is defective or not properly sealed to the engine. Be sure to use electrically conductive sealer
Jf the light still does not come on, the bulb is burned out or the wire~ from the bulb to the ignition switch and oil pressure switch are defective.
CHARGE INDICATOR LIGHT TEST
.To test the charge indicator light, turn the ignition switch on with the engine stopped. The light should come on. If it docs not. the bulb is burned out, or the wiring to the light is defective or there is a fault in the alternator/regulator circuit. Remove the wiring plug from the D+ terminal of the Bosch alternator regulator or the IND terminal of the Lucas alternator regulator.
Connect a jumper lead from the D+ or IND terminal in the cable to earth. The indicator light should come on.
If the light comes on the regulator is at fault. If the li,ght does not come on the fault is in the wiring or globe.
To check the globe and wiriug the instrument cluster surround n:ust be removed to gain access to the globe.
SPEEDOMETER TESTS
To test the odometer accuracy, drive the car over a measured kilometre (mile). Speedometer accuracy can be checked by comparing the speedometer in question against one known to be accurate, while two cars are moving at the same speed, or by timing the car on a measured kilometre (mile).
Page 15 24 shows the correct combination of gears to use for various rear axle and tyre size combinations .
15-6 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
EJ COMMON ADJUSTMENTS AND REPAIRS HORN ADJUSTMENT ADJUSTM~NT SCR~W
Horn current can be adjusted by changing the contact tension. Con-nect the horn as shown in Fig. 2. Turn the sel(-locking adjusting pan headed screw until the current is within the limits for the horn being adjusted.
TURN INDICATOR TURN INDICATOR
TERMINALS
WIRING LOOM SOCKET
HIGH OR LOW TON~ ID~NTIFICATION
FIG. 5- Horn Adjustment.
SEAT BELT WARNING HIGH BEAM
INSTRUMENT REGULATOR
FUEL AND TEMPERATURE GAUGE MASK RETAINING SCREWS
TEMPERATUREGAUGE VOUAGE TERMINALS
FIG. 3 - Falcon Printed Circuit. FIG. 4- Fairlane Printed Circuit.
15-7
PART 15-2 LIGHTING SYSTEM AND HORNS
Section Page Secdon Page I Description and Operation ................ 15-7 Parking Light ........................... 15-10
Headlights .............................. 15-7 Tail, Stop, and Back-Up Light Bulbs ........ 15-12 Horns .................................. 15-7 License Plate Light . .. ...... . .. ........ .. . 15-12
2 In-Car Adjustments and Repairs ... ...... .. 15-7 Dome Light .. . .......................... 15-12 Headlight Ahgnment .. . ......... ....... . . 15-7 Instrument Lights ......... ....... .... ... . 15-12 Headlight Adjustment ..................... 15-7 Horns .................................. 15·· 12 Back-Up Light Adjustment ................. 15-7 Horn Switch ............................. 15-1 2
3 Removal and Installation .......... . ....... 15-10 Gear Selector Quadrant Light . ..... ... .... 15-12 Headlights .............................. 15-10
D DESCRIPTION AND OPERATION
Refer to Group 22 for locations of wiring harnesses and schematics.
HEADLIGHTS The Falcon Models use tw_o
No. 2 type sea led-beam headlights. Each light has low -bea m and highbeam filaments.
The beam selector switch is incorporated in the turn indicator switch.
Quick disconnect terminals are also provid!!d on the left and right
of the radiator support assembly . The terminals are colour coded. Like colo ur terminals are c6nnect
€d together.
HORNS Standard and De- Luxe m odel s are
fitted "ith one low tone horn. On Fairmont, Futura and G.T. models a pair of tuned horns is used, one a high pitched tone, the other, which is similar to the single horn installation, has a low pitched tone. A horn button closes the circuit to the horn( s ).
EJ IN-CAR ADJUSTMENTS AND REPAIRS
HEADLIGHT ALIGNMENT
All headlight adjustments should be made with a half-full fuel tank plus or minus one gallon, with a person seated in the driver's seat, and a person in the passenger seat, the ear unloaded and the trunk empty except for the spare tyre · and jacking equipment, and recommended pressure in all tyres. Before each adjustment, bounce the car . by pushing on the centre of both the front and rear bumpers, to level the car.
To align the headlights by means of a wall screen, select a level por-
tion of the shop floor. Lay out th!' floor and wall as shown in Fig. 6.
HEADLIGHT ADJUSTMENT Adjust each upper headlight beam
as shown in Fig. 6. Some states may not approve of the 0 ±51.0 mm (2 inch) dimension for the headlights. Check the applicable state law.
Each headlight can be adjusted by means of two screws located between the light and radiator gri lle. (Fig. 7 and 8).
CAUTION Always _ adjust aiming !'crew
counter clockwi!\e th!'n clockwise until high intensity of lig-ht is
High and low tone horns can be identified by the letter "H" or "L" respectively cast into the throat of the horn .
NOTE: Horns are located forward of the left front suspension tower.
SEAT BELT WARNING LAMP.
All vehicles are fitted with a seat belt warning lamp.
A relny is used which illuminates the lamp for I 2-15 seconds after switching on the ignition .
properly aimed. Thi s will bring the beam into final position with the unit he ld under proper tension when uperation is co mpleted.
Note : Do not check aim on the
low beam.
BACK VI' LJ(;HT AOJUSTMENT
Place the shift lever in the reverse position. Loosen the switch retaining clamp and position the switch so that the operating plunger is depressed 1.6mm (1 1 16"). Ensure that the swite>h body is not contacting the shift arm and is parallel to the arm. Tighten the clamp.
15-8 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
I
I I j
{
~
~ '3 ~
~
... :II 0 > j
iii 3: "tl c .. ... 0 0
u:: I
co
~
""
PART 15-2- LIGHTING SYSTEM AND HORNS 15-9
FIG. 7 - Headlight and Parklight Installation - Falcon Typical.
0
FIG. 8 - Headl ight and Parklight Installation - Fairlane Typical.
''\ =::-it::»=---
iTL M
.) .. !:;
__!~ ..
I
P4J.,I(NO
1Jul5 I:JUJI I .)O!IJ
IJQJI !JD.)I ,JU99 UJOI
~ 10)
1-'Aid /li4M[ ""' ---- ---Hill/f. ft(AJ.. .. A/1/P LNII ~[IAJNINO ? BULB A:..NY 14£AQI.A .'IIU~ }IAL1 u ki/IIIA
:;;t.,RcW H{"A/.)t i.MP AD.111 . TJNf,~
Hlo"J(". HO.[)LAJ,ft:'i A,r.o;·~ TIIV· ~
@_IN6 H[Ae_LANJ.J A lJJtJ.. , Ti/111, )-/~).)11\ A._ ,,, f I"''["JJQLAMO ~'-'
J#.JL(.I/IJ(, A.:..J,S'! lii/JU1 AMl ' I H- - - -
6_
8 RING HY..D/..IVI'JP M:'TAINING
0 CLIP t4CA OLAMP SPRING AA8 0Q
0 BUL SA .HY 1-1£.A,Qu.Jr!IP (H4)
0 AII\G A .. H Y H O.DLA/'tAP HGH MAN!
@ RING ASJY HO.QLANP HIGH BU./\1
® ~DUSING ASSY ~ADLANIP
0 i-~OU.SINC ASJ I" Hf.AOU.MP
@) SCIUW H£ADLA.MPAD.JUSTJNG
® .5PAING HO DLANIP PAD Q£ T IVNtNG
@ NUT H£AlJL A ...,JD ,M;l.J41.$TI#(;
@, A l NG A..SSY H£ADLANPI.DII l!£AM
@ AINC A .S5Y H£.14Qi.N\11Pu;JW /JCA M
@ a ut.. • A.ssY 1-4£AOL AMP (1. • )
0 J.CR£1/lt/ 4 wA..JHCR A.SSY ii" ~C X "-'&AD
® ,f£T,Aii/tR < N(/T A SSY .)/,(.. • ld
(c) SCE'.t:'lV ( 111...4.9'/612 .49:>Y
15-10 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
EJ REMOVAL AND INSTALLATION
HEADLIGHTS
REMOVAL To replace the sealed beam unit,
remove the radiator grill and remove the three sealed beam retaining rim screws . Lift the sealed beam unit free of its cradle.
Remove the push-on 3-pin connector by holding the headlight assembly and applying a firm pulling
action to the connector. Remove sealed beam unit from vehicle.
REPLACEMENT Align the three-pin connector with
the contacts in the sealed beam unit and push on. Fit the sealed beam unit to cradle ensuring the three locating lugs engage in cradle locating slots. Fit the retaining rim and fit three screws.
Refit grill and aim headlights.
Whenever a sealed beam umt IS
replaced or any other alterations are made to a headlight assembly the headlights should always be checked for alignment and adjusted as described on page 157.
PARKING LIGHT Th.: parking light of Fairlane
Falcon vehicles is shown in Fig. 9,..10. To replace the bulb remove the lens
retaining screws and the lens.
-- ~.
BUBAS:5Y I . V . IS/#
I:.A51<Er fiWI1 /..AAIIP LEN5 c.EN5 TU!N .:£NAL CPTIC.:5
51-!ELD LAW' .5/E LEN5 fN?J(J\G LAMP BUB AS.SY
FIG. 9- Installation Drg. Park Lamps.- Fairlane
(!) LEN5 A55Y-QEAQ~BAD< UP! AMP LEN3.A5Sf-l2EJJI2t;84CK uP LMP
(21 80DY ASSY-REAk LA'viP
® CD G) @ (])
8U..8 A5~' 12V 21, 5/Y
BUB A5S Y 12 Y 2 /1'1
!mEL BACK LCWER (12H) PA/IEL QU412TEK (f?EF) EXT -0112 !1:1NEL (/2£F)
5CREW IWV flO • 8 · 32Y62
FIG. 10- Falcon- rear lamp installations.
XlEW "8·32 1WV HD AUT "8 u·T'rPE
5CREW ·8-32 Olt4L HD MiT "8·32 VTYPE
XREW C5·32 O~L .J.O .:a?EW "8 ~ !-() NUT IN5Ef2T <Z".tt"W-8·,6 CVU. tO TAWN3
I
/\OTE LEN5 AAD Bt.ZEL A.UY CAJINJT BE .e.Etl11JYED FIJJM L..AWJ A5jY W!THCVT FIQST QEI.Cf'N; LAMP FI<OM THE VEHICLE
PART 15-2- liGHTING SYSTEM AND HORNS
Fig. 11-Falcon Park lamps
13711 50CKE 7 {kEr)
Fig. 12-Hardtop Rear lamps
VIEW IN CIQCLE Z
(/ iY l(f! J WRNJ /M /1 Pi'. .\61\W 1NJ 1 J'M)
f2; l.!f::N - ~1( LAM/-' DXle (i?Ft=) Q• 8CVYA5>-~ LAM' If' c!Ui3 A5Y Gl 8U8A5Y 6\ LcN5-/::W21(,11l; L.A.-W (J) :XXKETt V1Y6 45Y 00' 1/MJ
® N.JT #0 WA::H:R A5Y "0-24 @ SCREW "6 qw HO C/REC 0 [CIE O P
Cf_! LENS A5Sr- .Q£4Q LA11P 2 ; BODY A 5SY- REAI< LAti!P .3; BULB 4) BULB
ii LIXK '\JUT E WASHE.Q
C -5CI<£W " 8 -32 f:14N HD lAPPING
15-11
15-12 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
TAIL, STOP, AND BACK-UP LIGHT BULBS
To replace the tail, stop, and/ or the back-up lights, remove the retaining screws and remove the icns. See Figs. I0-12- 13-14. LICENCE PLATE LIGHT
Bulb replacement is straightforward as there is no lens covering the licence plate bulb. DOME LIGHT
Remove the self fixing dome light lens and replace the bulb. INSTRUMENT LIGHTS
Instrument cluster illumination
lamp bulb replacement necessitates removal of the instrument cluster as described in Part 15-4.
Once the cluster has been removed simply remove the bulb holder from the cluster replace the bulb and reinsert the a~sembly in the cluster. GEAR SELECTOR QUADRANT LIGHT COLUMN SHIFT.
1. Gently prise the gear selector quadrant dial from the sleeving column.
2. Remove the globe. 3. Replace the globe and push
the dial assembly over the locating
pins. GEAR SELECTOR QUADRANT LIGHT FLOOR SHIFT.
I. Remove the console and dial assy .
2. Remove the globe.
HORNS
Disconnect the horn wire from the terminal. Remove the horn mounting bracket to horn retaining screws and remove the horn .
To install, mount the horn in position, then connect the horn wire to the horn terminal.
0 ...... · ~~· -~ ·--· @·~4--'* , ... ......... ,_ .. Q)•~• •.l/~ .... oV<> · .O·""' ~-
® .,.., < · ~ .. - · - · · @ ••• •• I• • oo• •u · · •'·"'" •-® .. ... ... ~-.---·"•<
0• •·• '" ' ••• "oo• ® · .... . . . . .... " ® ...... , .... . 0 ·- ••• •••• ··-"'""" r·
Fig. 13-Fairlane-Rear Lamp Installations
Fig. 14-Ute-Van-Rear Lamp Installations
0t.J460/I G AJK£ T A(A.<I. l u/W~ LC/W$~'01-0 1.}46 0/ t ~ .OU ... £ T t:I C.AR UO.MP l. CN.J
0 IJ 410 Al't D · RCA.R l A.I'IAP f\AOON r/Nt; t
e IJ 4.J<II/.S aoo .-.... .s s- ..- RLAAUIMP
0 t .J.J2 .. t LN.J IIICAR lAMP
® /J 4 5 c; L£N.J Pl.£tll/l 1VRH
0 1..) 4 '(.5 &V~A AU'(
( •) t ';;.t 9f> 6U<l':J ASS"
~..S'S OJ-- · ~.0 .SC. A~W
(8).•.t6B~·S.J l <;f:; Pl£W
15-13
PART 15-3
SWITCHES, CIRCUIT BREAKERS, AND FUSES
Section
Descript ion and Operation .. . . ... ........ . Headlight Switch . . . . .. . .. .. .. . . .. ..... . Fuse Panel. . . . . . . . . .... . . . . . . .. . .... . .
Section
Stop Light Switch
Dome Light Switch
Mechanical Stop Light Switch .. ..... .. . . .. .
Page 15-13 15-13 15-13 15-13 15-13 15-13 15-13
Ignition Switch and Lock Cylinder . ... .... .. . .
Page
15-14
15-14
15-14
15-14
15-14
15-14
Reversing L1ght Switch . . . ... . ...... ... .. . 2 Removal and I nstalla t iun .... .. .. .... . .. .
Windshic:ld Wiper Switch . .. . . ..... . ...... . .
Multi-purpose Switch . . . . . . . . ... ..... . . Neutral Start Switch .. ... . ....... .... . .. . . .
Hack-Up Light Switch . . . . . . . . . . . . . . . . . . . .
D DESCRIPTION AND OPERATION
Refer to Group 22 for locations of wiring harnesses and schematics. HEADLIGHT SWITCH
A separate headlight switch and circuit breaker is used. The headlight circuit is protected by a 22 ampere circuit breaker. The tail, parking. licence plate light and horn circuits are protectecl hy 8 amp fuses.
MULTI-PURPOSE SWITCH A multi-purpose switch is fitted
to the steering column immediately below the steering wheel and incorporates the following functions:
a. Turn indicator switch with a spring loaded "lane change" feature .
b. Headlight hcam selector with a spring loaded headlight "flash" feature .
c. A horn switch operated by pushing the end of the switch lever.
FUSE PANEL
The fuse panel is mounted on the right of the dash panel under the right-hand air vent. Fig.l S shows the
FIG. 15 - Fuse Panel Location -Typical.
fuses, their valves and locations.
MECHANICAL STOP LIGHT SWITCH
The mechanical stoplight switch is located on the brake pedal support hracl<et and 1s operated by a lever extending from the brake pedal arm.
With the brake pedal in the released position and a test lamp con-
EJ REMOVAL AND INSTALLATION
HEADLIGHT SWITCH 1. Disconnect the battery ground
cable.
2. Prise the switch forward from the instrument cluster.
3. Disconnect wiring and remove the switch .
4. Connect wiring to the switch connections.
5. Press the switch assembly into the aperture .
MULTI-PURPOSE SWITCH Removal
1. Remove the steering wheel. 2. Remove the four screws re
taining the steering column upper shroud, remove the filler piece from the shroud immediately below the switch lever and lift the shroud from the steering column.
3. Remove the two screws securing the switch to the steering column flange.
nected to the switch terminals adjust the switch as follows-
1. Release the locknuts retaining the switch body.
2. Move the switch body forward until the test lamp goe$ out.
3. Move the switch body a further 1.27 mm (0.050") forward.
4. Tighten the locknuts.
BACK-UP LIGHT SWITCH
The reversing light switch is incorporated in the inhibitor switch on automatic transmission vehicles.
In column shift manual transmission vehicles the plunger type switch is located on a bracket at the steering column lower bearing where it is actuated by the first and reverse shift lever.
On floor shift manual transmission vehicles the plunger type switch is mounted on a bracket on the front of the shift mechanism where it is actuated by the reverse shift lever as it reaches the reverse position.
4. Disconnect the two multi-pin wiring plugs from the switch and remove the switch. Installation
5. Counect the two wiring plugs to the switch.
6. Position the switch to the steering column flange ensuring that the gear selector quadrant light wires (if fitted) are not trapped behind the switch. Install and tighten the attaching screws.
15-14 SWITCHES, CIRCUIT BREAKERS AND FUSES
7. Install the steering column upper shroud and the steering wheel.
8. Check the operation of the switch.
STOP LIGHT SWITCH
1. Disconnect the wires at the connector.
2. Release the locknut (pedal side) and withdraw the switch.
3. Reverse the above procedure to replace the switch.
4. Adjust the switch as in section I.
DOME LIGHT SWITCH The dome light switch IS mcor
porated in the panel lamp switch. It is actuated by rotating the switch control wheel to the right when once the panel lamps have reached full brilliance. The further rotation of the wheel switches the dome lamp on .
The dome lamp also acts as a courtesy lamp actuated by switches m the door pillars.
IGNinON SWITCH AND LOCK CYLINDER
1. Disconnect the negative cable from the battery.
2. Remove the column from the vehicle .
3. Remove the steering lock shroud and shift tube. Page 3-38
4. Cut slots in the steering lock attaching bolts with a hacksaw and remove the bolts with a screw driver or hammer and centre punch.
FIG. 16- Typical Ignition Switch Removed .
5. Rotate the lock around the column tube until one end of the base clears the aperture, lift the lock from the column.
6. Place the steering/ignition lock assembly into the steering column
7. Engage new recessed bush in the shear head bolts and tighten them evenly until the heads shear off. Install shift tube.
8. Assemble tile shroud to the column.
9. Assemble the column to the vehicle. LOCK BARREL REPLACEMENT.
I. Remove the steering/ignition lock shroud lower attaching screw from beneath the shroud.
2. Turn the ignition key to the off or on position. ·
3. Push a 1.5 mm (0.062" diameter pin into the lock through the shroud lower mounting hole to raise the barrel locking pin and remove the barrel (Fig. 16).
4. Align the barrel tongue and aperture and assemble the barrel to the lock and raise the barrel locking pin by turning the key to the start position .
5. Assemble the lock shroud lower attaching screw.
WINDSHIELD WIPER SWITCH
1. Disconnect the battery cable. 2. Prise the switch from the
instrument cluster. 3. Disconnect wiring and remove
the switch. 4. Connect wiring to the switch
connections. 5. Press the switch assembly into
the aperture.
NEUTRAL START SWITCH See group 7 for replacement of
the neutral start switch on cars equipped with automatic transmissions.
BACK-UP LIGHT SWITCH 1. Remove the two wires from
the switch. 2. Loosen the retaining clamp or
locknuts. 3. Remove the switch.
PART 15-4 INSTRUMENTS
Section Pare 1. Description and Operation . . . . . . . . . . . . . . 15-15
Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-15 Constant Voltage Regulator . . . . . . . . . . . . . . 15-15 Fuel Gauge. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-15 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 15-15 Charge Indicator Light . . . . . . . . . . . . . . . . . . . 15-16 Oil Pressure Indicator Light . . . . . . . . . . . . . . 15-16 Turn Indicator . . . . . . . . . . . . . . . . . . . . . . . 15-16 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16 Brake Warning Lamp . . . . . . . . . . . . . . . . . . . 15-16
2. In-Car Adjustments and Repairs . . . . . . . . . . . . 15-16 Windshield W'!'er Blade Adjustment I Installation 15-16
3. Removal and Installation . . . . . . . . . . . . . . . . 15-17 Instrument Cluster ..................... 15-17 Fuel, Temperature Gauges . . . . . . . . . . . . . . 15-17 Printed Instrument Circuit . . . . . . . . . . . . . . 15-17 Fuel Sending Unit . . . . . . . . . . . . . . . . . . . . . 15-17
15-15
Section Speedomete-r and Tachometer ........... . . Speedometer Cable ................. .. . . . Temperature Sending Unit .............. . Oil Pressure Switch ..................... . Turn Indicator Flasher .... . .............. . Windshield Wiper Motor .. . ............ .. . Wiper Pivot Shaft and Link .............. .
4. Major Repair Operations ......... . ....... . Disassembly- Permanent Magnet Type Two-
Speed Electric Wiper Motor ...... . ..... . Inspecting and Testing Disassembled Motor ... . Testing and Assembled Motor ............ .
Pare 15-17 15-17
15-19 15-19 15-19 15-19 15-19
15-20
15-20 15-20 15-22
NOTE: If the instruments require servicing while the assembly is removed from the instrument panel, the cluster case must be earthed to the vehicle body. Failure to observe this precaution will cause immediate damage to the fuel and temperature gauges a:s soon as any power is applied to the electrical circuits.
D DESCRIPTION AND OPERATION
All of the instruments are electrically operated except the speedometer. Brightness of the instrument panel lights is controlled by a rheostat adjacent to the lighting switch.
GAUGES The instrument cluster includes
a fuel gauge, temperature gauge, charge indicator light, oil pressure indicator light, speedometer, high beam indicator light, a left and right-hand turn signal indicator light, brake warning light, and seat belt warning light.
CONSTANT VOLTAGE REGULATOR
The constant voltage regulator used with the fuel, temperature, and 'oil gauges maintains an average value of 5.0 volts at the gauge terminals.
The regulator operates by means of a bimetallic arm and a heating coil. When the ignition switch is turned on, the heating coil heats the bimetallic arm causing it to bend and break the contacts, disconnecting the voltage supply from the heating coil. The bimetallic arm then cools and brings the contacts together again. The making and
breaking of the contacts, causes a pulsating voltage, with an effective average value of 5.0 volts to be supplied to the gauges. Although these pulsations are quite rapid, there is in each gauge a bimetallic arm which changes temperature quite slowly, and this assures steady average readings.
As the pulsating voltage would normally cause radio interference, a radio interference suppression choke is connected in series with the constant voltage regulator supply wire.
FUEL GAUGE The fuel gauge consists of a send
ing unit, located on the fuel tank, and a remote register unit (fuel gauge) mounted in the instrument cluster. The remote register unit pointer is controlled by a bimetallic arm and heating coil. The sending unit is a rheostat that varies its resistance depending on the amount of fuel in the tank. The rheostat is operated by a float control. As the fuel level rises or falls the float control arm moved by the float, varies the resistance.
TEMPERATURE GAUGE The temperature gauge consists
of a sending unit mounted in the cylinder head at the top front on the V-8, and the left rear on the
six, with a remote register unit (temperature gauge) mounted in the instrument cluster.
·Changes of engine temperature vary the resistance of the sending unit which in tum operates the temperature gauge.
COil TEMPERATURE SENDING UNIT
Oil PRESSURE SWITCH
FIG. 17 -Oil Pressure Switch and Temperature Sending Unit 6 Cyl.
15-16 GROUP IS
CHARGE INDICATOR LIGHT
A red alternator charge indicator light is used. This light illuminates if the battery is discharging and the alternator is not supplying current.
When the ignition switch is closed, battery current flows through the charge indicator light and through the regu lator voltage limiter to the field.
When the alternator outp ut voltage t•pposing battery voltage is high enough the charge indicator light goes out.
OIL PRESSURE INDICATOR LIGHT
A red indicator light illuminates when the oil pressure is below a safe value. The light should come on when the ignition switch is first
LIGHTING SYSTEM, HORNS AND INSTRUMENTS
turned on, and it should go out when the engine comes up to speed. The light is connected between the oil pressure switch unit mounted on the engine at the left rear on the six, centre rear on the V-8, and the coil terminal of the ignition switch. The G.T. has an oil gauge adjacent to the tachometer.
TURN INDICATOR The turn indicator uses a single
filament globe in the upper section of the front park/ indicator combination lamp and the centre section of the rear light assembly.
The turn indicator flasher is located in the back of the instrument panel, on the steering column brace.
SPEEDOMETER
The speedometer is connected to the output shaft of the transmission by means of a flexible shaft, and a drive gear located inside the transmission. The flexible shaft drives the speedometer which registers speed in kilometres (miles) per hour and also drives an odometer which records distance trav .::!led in miles and tenths of a mile.
BRAKE WARNING LAMP
A red indicator lamp illuminates when either the front or rear brake systems become inoperative. The warning light switch is located in the master cylinder body.
"Prove out" of the light circuit is conducted by turning the ignition switch to the start position when the lamp should illuminate.
EJ IN-CAR ADJUSTMENTS AND REPAIRS
WINDSHIELD WIPER BLADE INSERT REPLACEMENT
Removal 1. Raise the wiper blade assem
bly from the windscreen until it is just clear of the screen and support the arm in this position.
2. Compress the retaining clip at the end of the blade assembly with the fingers and slide the insert and its metal backing strip from the blade as~cmbly. Installation
3. Slide the insert and its metal backing strip into the blade until the spring clip snaps into position.
Fig. 18--Wiper Blade Removal
4. Remove the support from the wirer arm and lower the blade to the screen.
WINDSHIELD WIPER ARM AND BLADE ASSEMBLY ADJUSTMENT OR REPLACEMENT
Removal I. (Driver's side only) . Discon
nect the articu lating link from the pivot post by sliding the retaining clip along the link and lifting the link clear of the pivot pin.
2. Raise the arm to the full extent of its travel (DO NOT USE FORCE), then rotate the lock plate on the pivot post end of the arm in a clockwise direction. Gently lower the arm which will then be held slightly away from the windshield.
Fig. 19-Wiper Arm Lock Plate
3. Remove the arm assembly from the pivot post spindle.
CAUTION: DO NOT USE FORCE WHEN REMOVING OR REPLACING THE ARM ASSEMBLY AS DISTORTION OF THE ASSEMBLY WILL OCCUR. Installation
4. Ensure that the arm is held in the locked position with the lock plate holding the assembly in a straight line. (Fig. 19 ).
5. Position the arm assembly on th ~ spindle with the blade 38-63 mm (Jt-2t ") from the lower edge of the windscreen (measured at the centre of the blade).
6. (Driver's side only). Fit the articulating link to the pivot pin and secure it with the spring clip.
7. Raise the arm to the extent of its travel (DO NOT FORCE).
Lock Plate
Rotate the lock plate in an anticlockwise direction and gently lower the arm to the screen.
WIPER BLADE ASSEMBLY
Removal 1. Remove the arm and blade
assembly as described in the pre-
PART 15-4 INSTRUMENTS
vious operation. 2. Using a small screwdriver
through the aperture in the blade assembly depress the spring, remove the pivot pin. (Driver's side only). Separate the blade from the arm. Installation
3. Driver's side. Position the
EJ REMOVAL AND INSTALLATION
INSTRUMENT CLUSTER
I. Remove the three screws, (five screws Fairlane) retaining the cluster housing.
2. Remove the housing toward the steering column.
3. Disconnect warning lamps (and /or Gauges G .T.).
4. Remove the housing from behind the steering column by moving it toward the centre of the vehicle (select 1st or 1 gears on column shift vehicles).
5. Remove the four cluster retaining screws (one in each corner of the cluster body) , and partially remove the cluster.
6. Disconnect speedo cable and printed circuit plug.
7. Complete removal of the cluster by rolling the top back toward the column.
SPEEDO CABLE DISCONNECT FROM SPEEDO HEAD
1. Remove the crash pad end cover (from right hand side).
2. Using a long screw driver or solid rod depress the release tab and pull the cable away from the speedo head. (Fig. 20).
FUEL & TEMPERATURE GAUGES
I . Remove the instrument cluster as previously outlined .
PULL CABLE AWAY FROM HEAD
2. Remove the two upper screws retaining the lenses and the two screws holding the two halves of the cluster together.
3. From the front of the gauges, remove the two screws retaining the fuel gauge mask, unclip the mask from the temperature gauge mask and remove it from beneath the needle.
4. Remove the terminal speed nuts retaining the gauges to the rear half of the canister and remove the gauges.
NOTE : The fuel gauge mask must be removed before the temp gauge or mask can be removed.
FUEL & TEMPERATURE GAUGES G.T. &G.S.
I. Remove the instrument cluster housing (3) retaining screws and lay the housing toward the steering column.
2. Remove the gauge wiring and disconnect the warning lamp holders from the housing.
3. Remove the housing from behind the steering column and remove the gauge retaining screws.
4. Remove the gauges from the housing. FUEL & TEMPERATURE GAllGES FAIR LANE.
I . Remove the instrument cluster as previously outlined.
FIG. 20 - Speedo Cable to Speedo Connection.
15-17
blade assembly in the arm. Depress the spring and insert the pivot pin.
4. Passenger's side. Depress the spring and assemble the blade to the arm.
5. Replace the arm and blade assembly as described in the previous operation.
2. Remove the four screws attaching the lens and cover to the canister.
3. Remove the terminal speed nuts from the gauges and remove the gauges from the canister.
SPEEDOMETER & TACHOMETER.
I . Remove the instrument cluster and separate it as previously outlined under fuel and temperature gauge removal.
2. Remove two retaining screws from the backs of the speedometer/ tachometer.
NOTE : On Fairlane remove fuel and temperature gauges prior to attempting to remove the speedometer.
3. Remove the speedometer/ tachometer from the cluster.
PRINTED CIRCUIT. Replacement of the printed circuit
can only be achieved once the gauges - speedometer/tachometer have been removed. Fig. 3 & 4.
CLOCK.
I. Remove the instrument cluster housing.
2. Remove the instrument panel pad, right hand end cover.
3. Remove the two clock attaching screws.
4. Disconnect the clock leads. 5. Remove the clock through the
end opening in the instrument panel.
WARNING LAMPS.
1. Remove the instrument cluster housing.
2. Remove bulb holders from the housing. NOTE: On Fairlane vehicles remove the heater control panel to gain access to the brake warning lamp.
FUEL SENDING UNIT 1. Remove the fuel from the fuel
tank.
,\
3
CONNECTIONS MA Y 8£ i!£VER5EO
1?£.)/WN!TE 11'11JiaR A'T£CT/NG
'\;;: {_::, ;,:;;:;,:j-1 \ 1'\ I \ GII££N(/GN)
;-f /T. ~----+--'"-"0~ ~LACK - -L / ~~ [{'~'~~.l ~ \ Bo' l :;r itAI?TJ./)
o .. ~,tj ""-,
,/_ ! "IF fl. l t/M II'• • r /{ 'It !;,{)(f.£T A.>..)Y5 ( N,wlf'IK, "'ltu"/r t AOf ~' ~· t.ACk)
YI[W IN OII<[CTION c.,. , AN~'JW Y ':HJWI/Vf , ELE(; lh i(../IL CONIYirTit:'•'vJ 'o~C()UIR£0
F '.JH IN .)T/1.t.I.. A TIUIV ( AUV1n()lt(AL T0 $1ANL.;4/i>/)NOt./~IN(.)
MODU.;; ';4H [. 65H .'/IL f
FIG. 21 -Installation Drg. Cluster Housing.
0
ALL FALCON MODEL5 EXCEPT 54H C.65 H
F I T WARNING £AMP .JOCK£r A.SSY.S A r NI/M8£/l£b LOCA7t 0NS I N ACCORDANCE N l rH WI~IN6 1./J£Nrt.CI CATION SCH£0(.1££ 8£LOW : @ 8LU£/ WHI T£ <I GHEEN
0 8LACK/ YEl.LOW<I Glf££N
@) WHIT£~ Glf££N
@ Y£LLOW/ 8LACK 4 8~ACK ·
@ GlfE£N/ 8LACK 4 8LACK
(j)
ENS UR£ LOWER £/)(i~ OF HOUSING £N6AG£S
CUI'S <1 SNAPS I NTO PLACE
2
ALL FALCON M JULS EXCEPT 54H i-6:5 H
(1) IOAB92 . dLYL A.S.S Y.
0 1083~ H(}U:,tNG ASS~
0 5S9J0·52 50/EW
MODELS 54H C. 65H
0 IOA892 SE Zf:L A S5 Y.
0 10838 HOUSING A55Y.
@ @ S>Y.?!I -52 SCREW
@ IOA846 CLUST£A .ASSY INDICATO,q ENGINE
{J) ! OA6+6 CLUST£11 ASSY tNLJ ICATO.R AUX
© S~7.JZ·SZ SCIIEW
-Ul I
00
Q s c .,. -Ul I
G> I --t
z G>
~ ~ m ~ I 0 :;o z CJ)
)> z 0
z ~ :;o c ~ m z ~
MOUNTING CLIP
FIG. 22- Speedo Driven Gear.
2. Disconnect the fuel gauge sending unit wire from the sending unit.
3. Loosen the hose clamp and disconnect the tank line at the sending unit.
4. Remove any dirt that has accumulated around the sending unit so that it will not enter the tank.
5. Turn the sending unit retaining ring counterclockwise and remove the unit , retaining ring, and mounting gasket.
6. Clean the fuel gauge sending unit moun!ing surface at the fuel tank.
7 Position the sending unit and mounting gasket on the fuel tank and secure with the retaining ring.
8. Connect the sending unit wire and the fuel tank line.
9. Fill the tank with the fuel removed .
10. Check the fuel gauge operation and check for leaks. TEMPERATURE SENDING UNIT
t. Disconnect the temperature sending unit wire from the sending unit
2. Prepare the new temperature sending unit for installation by applying a small amount of conductive water-resistant sealer to the threads .
3. Remove the temperature sending un.it from the cylinder head and immediately install the new temperature sending unit .
4. Connect the wire to the temperature sending unit.
PART 15-4 INSTRUMENTS
SPEEDCMETER DRIVEN GEAR
'
/
5. Start the engine and check the sending unit operation.
OIL PRESSURE SWITCH To replace the unit disconnect the
wire from the terminal. Remove the unit from the engine. Apply conductive sealer to the threads and install the wire to the terminal and check the operation of the unit.
TURN INDICATOR FLASHER Disconnect the wires from the
flasher unit terminal, turn flasher and remove. Observe the colour code and number on the cover of the flasher. Be certain to replace it with a new flasher with the same colour code and number on the cover.
WIPER PIVOT SHAFT AND LINK 1. Remove the windshield wiper
blade and arm assembly. 2. Remove the-pivot shaft retain
ing nut, bezel and gasket. 3. Disconnect the wiper link from
the motor and remove the link and pivot shaft assembly.
4. Position the link and pivot shaft assembly on the cowl and wiper motor. Connect the link to the motor.
5. Install the pivot shaft to the cowl and install the gasket, bezel, and retaining nut.
6. Install the wiper blade and arm assembly.
15-19
7. Check the pivot shaft and link operation.
WINDSHIELD WIPER MOTOR AND WASHER ASSEMBLY
REMOVAL
1. Disconnect the harness from the Wiper Motor.
2. Remove the t!lree hoses connected to the Washer Pump.
3. Remove the three bolts retaining the Wiper Motor and mounting seal assembly to the dash panel. Lower the assembly aQd disconnect the wipe~ !inks at the motor. Remove the Motor and Washer Assemblv. INSTALLATION
1. Position the Motor and Washer Assembly and assemble the connecting wiper links to the motor.
2. Position the Motor and Washer assembly to the dash panel and install three retaining bolts.
3. Connect the harness connector to the Wiper Motor.
4. Connect large hose to inlet and two small hoses to outlet connections on washer pump.
5. Connect the battery and check the operation of the Wiper Motor and the 'park position' of the Wiper Blades.
WIPER PIVOT SHAFT AND LINK REMOVAL
1. Remove the windshield wiper blade and arm assembly.
2. Remove the nine cowl panel attaching screws and remove the cowl panel.
3. Remove s1x bolts retaining pivots.
4. Disconnect the wiper link from the Motor and remove the link and pivot shaft assembly.
INSTALLATION
1. Position the link and pivot shaft assembly on the cowl and wiper motor. Connect the link to the motor.
2. Install the pivot shaft to the cowl and install six bolts to retain pivots.
3. Install the cowl panel. 4. Install the Wiper Blade and
Arm Assembly. 5. Check the Pivot Shaft and Link
operation.
15-20 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
IJ MAJOR REPAIR OPERATIONS (Preslite)
FIG. 23- Wiper Motor Assy.
ITEM DESCRIPTION ITEM DESCRIPTION 1 Clamp Nut 3 Seal
2 Motor Crank Assembly 4 Grommet Insert
5 Terminal Block Assembly 6 Gear Housing Assembiy 7 Distance Washer 9 Thrust Cone
11 Terminal
8 Gear & S~ft Assembly 10 Washer Pump Assembly 12 Screw
13 Brush 15 Screw
14 Brush Spring 16 Spring Washer
17 Armature Assembly 18 Ball 19 Thrust Pad Assembly 20 Motor Housing Assembly 21 Wave Washer 23 Screw
DISASSEMBLY PERMANENT MAGNET TYPE TWO SPEED ELECTRIC WIPER MOTOR
1. Remove the clamp nut (1), Motor Crank, Assembly (2), Wave Washer (21), Flat Washer (7), Grommet Insert (4) and Mounting Seal (3).
2. Clean the gear housing of old grease. Do not allow cleaning fluid to contact the armature shaft and output shaft bearings. Wipe all other parts with a clean cloth.
3. Remove the two screws ( 15), lockwashers (16) and motor housing assembly (20). Do not pound the Motor housing assembly as the ceramic magnets may be damaged. Remove the ball (18) and thrust pad assembly (19).
4. Note: That the ball may have dislodged and become attracted to the magnets during the dismantling operation, and it is ·essential that this
22 Earth Finger
item is located. 5. Retract the brushes ( 13) and
withdraw the armature assembly (17) and thrust cone (9).
6. Remove the four screws (1 2), Terminal (11) and Washer Pump Assembly (10).
7. Disconnect the feed wire (miniature terminal) from the wiper motor.
8. Remove the gear and shaft assembly (8) and distance washer (7).
9. Insert screwdriver in slot at base of terminal block assembly (5). Prise upwards to free terminal block assembly, unsolder wires and remove from housing (6).
10. Remove self-tapping screw (23) and earth finger (22).
INSPECTING AND TESTING THE DISASSEMBLED MOTOR
1. Cover motor housing bearings and blow dust from interior with
compressed air. 2. Visually inspect for damage to
the ceramic magnets-replace motor housing assembly if necessary.
3. Visually inspect the armature assembly for burned commutator bars, galling or pitting of the armature shaft bearing area and worm gear for scoring. Check thrust ball for pitting, balling or discolouration due to heat. Replace if necessary.
4. Test for grounded armature. Obtain a test lamp and battery, connect one probe to the armature shaft or armature stack, and touch each commutator segment in turn with the other probe. The lamp should NOT light. If the lamp lights the armature is grounded and must be replaced.
5. Inspect the brush holder plate for cracks or damage. Ensure that brush boxes are secure and that connections are not burned or corroded.
PART 15-4- INSTRUMENTS 15-21
7
6 3 8
~ s 4
~ ~ t" ~\2 lO
'"'14 FIG.24
ITEM DESCRIPTION ITEM DESCRIPTION 1 Housing Assembly 2 Solenoid Assembly 3 Suction Cap 4 Plunger 5 Trim Cup 6 Cover 7 Valve Cover 8 Valve Seat 9 Valve Seal
11 Screw 13 Bush
6. Replace motor brushes that are worn down to 6 mm ( t") long. Examine brush springs for distortion, burning or collapse. Normal brush spring length is 38.1 mm (1 t") minimum. Replace if necessary.
7. Examine the gear housing for cracks and distortion, and the bearings for excessive wear. Examine the three parking fingerS for loss of tension, burning or pitting. Replace gear housing assembly if necessary.
8. Examine the gear and shaft assembly for worn or damaged teeth. Check cam for wear on face. Replace if necessary.
ASSEMBLY 1. Apply grease to the centre
drilled holes in each end of the armature shaft. Assemble the Thrust Cone (9) to the worm end of the sha(t and the 4.76 mm (3 / 16") diameter ball (18) to the other end of the shaft.
2. Assemble brusn :springs (14) and brushes (13) to the gear housing
10 Valve Rubber 12 Plunger & Lever Assembly 14 Spring
assembly. 3. Retract the brushes and assem
ble the armature assembly (17) to the gear housing assembly.
4. Apply stiff grease to the back face of the thrust pad assembly (19) and locate in the recess in the bottom of the motor housing assembly (20).
5. Assemble the motor housing assembly (20) to the gear housing assembly (6). Ensure that the wiring to the brushes does- not foul the motor housing. Assemble the two screws
(15) and lockwashers (16). 6. Adjust armature shaft thrust
screw in until resistance is felt and then back off screw a quarter turn.
7. To secure earth finger (22) to gear housing (6), install screw (23).
8. Install terminal plate assembly (5) to gear housing. Ensure that flanges on terminal plate assembly are located in receiving slot in housing (6).
9. Apply No. 2 cup grease to parking plate and cam track (8).
10. Assemble the distance washer
(7) on the gear shaft assembly (8) and assemble gear and shaft assembly to the gear housing.
11. Install mounting seal (3) to gear housing and assemble grommet insert ( 4).
12. Connect washer lead connector to wiper motor terminal, assemble washer pump assembly (10), terminal (11) and four selftapping screws ( 12). Re-locate selftapping screws carefully in existing threads to avoid stripping and tighten screws to a torque loading of 2.2-2.8 Nm (20-25 lbs. ins.).
DISASSEMBLY WASHER PUMP
1. Remove the four screws (11) attaching valve cover, remove valve cover (7), valve seal (9), valve seat (8), suction cap (3), trim cup (5) and plunger ( 4).
2. Remove solenoid assembly (2), with cover from housing assembly (I), dismantle plunger and lever assembly (12) and solenoid cover (6).
3. Remove bush (13) and spring (14).
15-22 GROUP 15· LIGHTING SYSTEM, HORNS AND INSTRUMENTS
INSPECTING AND TESTING DISASSEMBLED WASHER PUMP
1. Check operation of non-returned valves in valve assembly.
2. Check suction cap for damage or cracks or deterioration.
3. Examine trim cap, solenoid lever and plunger for damage or wear.
4. Check solenoid windings for continuity or short circuit.
5. Examine housing bush for dam·age and excessive wear.
6. Check compression spring for damage.
7. Examine washer housmg and latch for cracks and distortion, examine timing gear for worn or damaged teeth.
Note: Timing gear should rotate only when latch is retracted.
ASSEMBLY OF WASHER PUMP
1. Apply No. 2 cup grease to latch mechanism (1).
2. Install spring (14) and guide bush (13) to housing.
3. Install plunger and lever assembly (12) to solenoid assembly (2).
4. Install solenoid to housing taking care that lever engages wit~ sl~t in latch. Ensure that solenmd 1s located in receiving slot in housing and solenoid wire is correctly positioned in housing assembly.
5. Install trim cup (5) and plunger ( 4) to suction cap (3).
6. Install solenoid cover (6) to snap fit over location pin.
7. Install suction cap assembly and ensure that plunger is located in guide bush.
8. Install valve seat assembly (8, 10) and valve seal ( 4).
9. Install valve cover (7) and secure with four screws (11) tighten to a torque loading of 1.1-1. 7 Nm (10-15 lbs. ins.). TESTING THE ASSEMBLED MOTOR
1. Obtain a switch assembly ARC9DF.17A553-A, a 12 volt automotive battery and an 0 to 10 amperes Ammeter.
2. Connect the Negative terminal of the battery to the motor earthing terminal (11) and the 'E' terminal of the switch assc;mbly.
3. The terminal block assembly has four terminal blades and the moulding has four identification numbers 1 to 4 respectively. The switch assembly moulding also carries identification numbers .
4. (i) Connect motor terminal No. 1 to switch terminal No. 1.
(ii) Connect motor terminal No. 2 to switch terminal No.2.
(iii) Connect motor terminal No. 3 to POSITIVE battery terminal.
(iv) Connect motor terminal No. 4 to switch terminal No.4.
(v) Connect washer pump terminal to switch terminal 'W'.
5. Open te switch assembly and check for LOW speed and HIGH speed operation. Switch to park position two or three times and check that the motor crank assembly stops with a positive action in the same pcsition.
6. Switch motor to low speed and back-off the adjusting screw in the gear housing at the end of the armature shaft. Adjust end play of the armature by tightening the screw until an ammeter in series shows a slight rise in current. Back-off slightly until the current is just normal, apply 'LOCTITE-GRADE CV' to the screw to prevent unlocking.
7. Check the current consumption after running the motor for 30 minutes. The consumption should be 2 . 5 amperes maximum at 13 . 5 volt and the output speed 40 rpm LOW and 65 rpm HIGH.
8. Energising the solenoid of t~e washer pump, the current consumption should not exceed 2 amperes over the motor consumption during the energising period at 13 . 5 volts ± 0.1. Washer should complete four discharge cycles per one revolution of the wiper motor output gear and 12-16 discharge cycles for one wash cycle.
PART 15·5 SPECIFICATIONS
CIRCUIT PROTECTION
Function
Dome Courtesy
R/H Tail, Park Licence
L/H Tail & Park
Stop Light
Turn Signals
Radio
Heater Cigar Lighter
Windshield Wiper and Back Up Lamps
Light-Instrument Panel Light-PRNDL Dial
Light-Luggage Compartment
Light-Glove Box Light~Headlights
Horns
15-23
location Rating Time
Fuse Panel 8 8Amp Fuse Panel 6 8Amp
Fuse Panel 5 8 Amp
Fuse Panel 7 16Amp
Fuse Panel 4 8Amp Fuse Panel 2 8Amp Fuse Panel ' 16Amp
Fuse Panel 2 8Amp
Fuse Panel 2 8Amp Fuse Panel 4 8Amp Fuse Panel 6 8Amp
Fuse Panel 6 8Amp
Fuse Panel 8 8Amp
Fuse Panel 8 8Amp
Circuit Breaker 9 22Amp
Fuse Panel 3 8Amp
NOTE: There is a Circuit Breaker located on the starter relay and It controls the Accessory Relay (power windows and heated backlite) . It is rated at 20 amps.
BULB CHART
Unit
Headlight ALL MODELS
Front Turn Signal
Park ing
Rear Turn Signal
and Stop / Ta il
License Plate
Back Up Lights (Sedan) Back Up Lights (Stat. Wagon)
Luggage Compartment
Cargo Light (Wagon)
Dome Light
HORN
I Horn current dr11w 11t 12V
INSTRUMENTS
Fuel and T emper11ture Gauges Aver11ge volt11ge 11t termin~~ls
TURN INDICATOR
I Current dr11w 11t 12V
Wattage
50/75
21
6
21
6/ 21
6
21
21
10
10
10
4--5 Amps
5 Volts
0.4 Amps I
BULB CHART (Continued)
Unit Wattage
Warning Light Oil and Altern11tor 2.2 Brake Warning Light 2.2 Radio Dial 2.0 Turn Signal (Ins. Panel) 2.2 Instruments (Illumination) 2.2 Heater Control 2.2 Hi Beam Indicator 2.2 Speedometer 2.2 Glove Compartment 5.0 Courtesy Light Fairmont 15 Front and Rear Door Automatic Transmission Control 2.2
HEATER MOTOR CURRENT DRAW
At low speed At high speed
SPEEDOMETER CABLE
Mounting Clip Bolt Torque
~.5 Amperes 11t 12V
5.6 Amperes at 12V
4.1-6.1 Nm 3--4! Ft. Lbs.
15-24 GROUP 15- LIGHTING SYSTEM, HORNS AND INSTRUMENTS
WINDSHIELD WIPER MOTORS PRES LITE CURRENT CONSUMPTION
(HOT) OUTPUT SPEED
(HOT)
SPEEDO GEAR COMBINATIONS
Engine Transmission
6 Cyl. B.W. Manual 3 & 4 Speed & Auto
6 Cyl. B.W. Manual 3 & 4 Speed & Auto
8 Cyl. 6 Cyl. 5.0! : B.W. (302 CID) Manual 3 & 4
Speed
8 Cyl. U.S. C4 5.01. Auto (302 CID)
8 Cyl. B.W. 5.8 t 4 Speed (351) 2V & 4V
8 Cyl. U.S. 4 Speed 5.81'(351) RUG -BF
4V
8 Cyl. U.S. C4 5.8 t Auto (351) 2V
8 Cyl US. FMX 5.8 t Auto (351) 4V
2.5 Amp maximum at 1 3.5 V.
Axle Ratio
3.23 :1
3.50 :1
2.92 :1
2.92 1
3.0 :1
3.00:1
2.75 :1
2.75 :1
HIGH 65 R.P.M . LOW 40 R.P.M .
Tyre Size
6.95 X 14 7.35 X 14 7.75x14
ER70 x 14 185 X 14
6.95 X 14 7.35 X 14 7.75x14
ER70 x 14 1 8~ X 14
6.95 X 14 7.35 X 14 7.75 X 14
ER70 x 14 185 X 14
6.95 X 14 7.35 X 14 7.75 X 14
ER70 X 14 185 X 14
7.35 X 14 7.75 x 14 185 X 1 4
ER70 X 14
ER70 X 14
6.95 X 14 7.35 X 14 185 X 1 4
ER70 X 14 7.75 X 14
6.95 X 14 7.35 X 14 185 X 14
ER70 X 14
No. Of Teeth Driving Gear
(8) (8) (8) (8) (8)
(8) (8) (8) (8) (8)
(8) (8) (8) (8) (8)
8 8 8 8 8
8 8 8 8
7
8 8 8 8 8
8 8 8 8
No. Of Teeth Driven Gear Colour
(21) (lt. Green) (21) (Lt. Green) (20) (Brown) (21) (Lt. Green) (21) (Lt. Green)
(23) (Black) (22) (Grey) (22) (Grey) (23) (Black) (23) (Black)
(19) (Pink) (19) (Pink) (18) (Purple) (19) (Pink) (19) (Pink)
i9 Tan 19 Tan 18 Grey 19 Tan 19 Tan
19 Pink 19 Pink 19 Pink 19 Pink
17 Purple
18 Grey 18 Grey 18 Grey 18 Grey 17 Natural
18 Grey 18 Grey 18 Grey 18 Grey
top related