finol brake fluid dot 4 esp · finol brake fluid dot 4 esp has been specially formulated to enable...
Post on 14-Jul-2018
217 Views
Preview:
TRANSCRIPT
FINOL OILS LTD3 STANNAWAY DRIVECRUMLINDUBLIN 1201 4555 484
APPLICATIONS
SPECIFICATIONS
TYPICAL CHARACTERISTICS
BRAKE FLUID DOT 4 ESP
A material safety data sheet conforming to the regulations in use in the E.C. can be down loaded from www.finol.ie
Page 1 of 3
A very high speci�cation universal brake & clutch �uid.
Finol Brake Fluid DOT 4 ESP has been specially formulated to enable Electronic Stability Program (ESP) systems to operateover a wide temperature range. Suitable for all ESP and other conventional brake systems using Glycol Ether based Brake Fluids.
Finol Brake Fluid DOT 4 ESP meets the following International Speci�cations:- US FMVSS 116 DOT 4, DOT3, SAE J 1703, SAE J 1704- ISO 4925 (Classes 3, 4 & 6)
Finol Brake Fluid DOT 4 ESP also conforms to many other International & manufacturers’ Standards.Details are available on request.
Dry Equilibrium Re�ux Boiling Point, ˚CWet Equilibrium Re�ux Boiling Point, ˚CKinematic Viscosity @ - 40 ˚C, cSt @ 100 ˚C, cStpHHigh Temperature Stability, ˚CChemical Stability, ˚CEvaporation, %w/wFluidity & Appearance @ - 40 ˚C @ - 50 ˚CWater Tolerance @ - 40 ˚C @ 60 ˚CCompatibility @ - 40 ˚C @ 60 ˚CColour, VisualWater Content, %Density @ 20 ˚C, g/ml
TYPICAL RESULTS2671726752.108.53
-1+161
Pass, 4 secondsPass, 8 secondsClear, 3 seconds
Clear, No sedimentClear, No strati�cation
Clear, No sedimentPale Amber
< 0.201.052
Finol Brake Fluid DOT 4 ESPSheet updated: 26/05/2015
SPECIFICATION260 ˚C. Min.165 ˚C. Min.
750 cSt Max.1.5 cSt Min.
7 - 11.5+/- 3.0 ˚C. Max.+/- 3.0 ˚C Max.
80% Max.No freezing, Bubble time 10 sec. Max.No freezing, Bubble time 35 sec. Max.
10 seconds Max.Sediment not to exceed 0.05% v/v
No strati�cationSediment not to exceed 0.05% v/v
Water white to amber Not requiredNot required
Test
FMVSS 116FMVSS 116
ASTM D 445
260 Min.165 Min.750 Max.
Equilibrium Re�ux Boiling PointWet Equilibrium Boiling PointKinematic Viscosity at -40°C
Units
TEST REQUIRED
Method Speci�cation
°C°CcSt
FINOL OILS LTD3 STANNAWAY DRIVECRUMLINDUBLIN 1201 4555 484
BRAKE FLUID DOT 4 ESP
Page 2 of 3
A material safety data sheet conforming to the regulations in use in the E.C. can be down loaded from www.finol.ie
Finol Brake Fluid DOT 4 ESPSheet updated: 26/05/2015
CORROSION RESISTANCE
Tinned Iron ∆ mg/cm² Appearance Steel ∆ mg/cm² AppearanceAluminium ∆ mg/cm² AppearanceCast Iron ∆ mg/cm² AppearanceBrass ∆ mg/cm² AppearanceCopper ∆ mg/cm² AppearanceZinc ∆ mg/cm² AppearanceFluid AppearanceSediment %pHRubber Diameter Change mmHardness Change ˚IRHDAppearance
OXIDATION RESISTANCE
Cast Iron ∆ mg/cm² AppearanceAluminium ∆ mg/cm² Appearance
TYPICAL RESULTS-0.03Good-0.01Good
NilGood-0.03Good-0.08Good-0.05Good0.01
GoodPass
< 0.058.200.16
-4Pass
0.04Pass0.02Pass
SPECIFICATION0.2 Max.
No pitting or etching0.2 Max.
No pitting or etching0.1 Max.
No pitting or etching0.2 Max.
No pitting or etching0.4 Max.
No pitting or etching0.4 Max.
No pitting or etching0.2 Max.
No pitting or etchingNo crystallisation or gelling
< 0.1%7 - 11.5
1.40. Max.-15 ˚IRHD Max.
No sloughing, blistering or disintegration
0.3 Max.No pitting or roughening
0.05 Max.No pitting or roughening
TEST REQUIRED
FINOL OILS LTD3 STANNAWAY DRIVECRUMLINDUBLIN 1201 4555 484
BRAKE FLUID DOT 4 ESP
Page 3 of 3
EFFECT ON RUBBER
SBR @ 70 ˚C Ø change, mm ∆ Hardness, IRHD ∆ Volume, % Appearance
SBR @ 120 ˚C Ø change, mm ∆ Hardness, IRHD ∆ Volume, % Appearance
EPDM @ 70 ˚C ∆ Hardness, IRHD(as required by SAE J1730) ∆ Volume, % Appearance
EPDM @ 120 ˚C ∆ Hardness, IRHD ∆ Volume, % Appearance
Natural @ 70 ˚C Ø change, mm(as required by ISO 4925) ∆ Hardness, IRHD ∆ Volume, % Appearance
TYPICAL RESULTS0.56
-36.21
Good
0.73-7
7.69Good
-21.39
Good
-21.91
Good
0.38-5
4.61Good
SPECIFICATION0.15 to 1.40
0 to -101 to 16
No blistering, sloughing ordisintegration
0.15 to 1.400 to -151 to 16
No blistering, sloughing ordisintegration
0 to 100 to -10
No blistering, sloughing ordisintegration
0 to -150 to 10
No blistering, sloughing ordisintegration
0.15 to 1.400 to -101 to 16
No blistering, sloughing ordisintegration
TEST REQUIRED
A material safety data sheet conforming to the regulations in use in the E.C. can be down loaded from www.finol.ie
Finol Brake Fluid DOT 4 ESPSheet updated: 26/05/2015
top related