hardware manual of t20
Post on 29-Nov-2014
177 Views
Preview:
TRANSCRIPT
ZKS Group (Shanghai)
Contents
1. Basic Introduction of the Fingerprint Time Attendance and Access Control
Terminal ………………………………………………………………………………………..…2
1.1 Appearance…………………………………………………………………………………...2
1.2 Technical Indicators…………………………………………………………………….…….2
1.3 Interface Definition…………………………………………………………………………...3
1.4 Keyboard Description……………………………………………………………………......4
2. Equipment Connection……………………………………………..…..
…………………...4
2.1 Communication via RS232……………………………………………………………..……
4
2.2 Communication via RS485 ( the distance can be as far as 1200 m )………………..…4
2.3 RS485 Communication with Multi Sets of Fingerprint Terminals…………………..…..5
2.4 TCP/IP Communication with Multi Sets of Fingerprint Terminals……………………....5
3. Function Setup……………………………………………..…………………..…..………...5
3.1 Menu ………………………………………………………………………………….
……….5
3.2 Data Proc ……………………………………………………………………………………..5
3.2.1 User
Reg…………………………………………………………………………………….5
3.2.2 Admin Reg…………………………………………………………………………………..6
3.2.3 Sensitivity……………………………………………………………………………………
6
3.2.4 Delete……………………………………………………………………..…………………6
3.2.5 View URec…………………………………………………………………………………..7
3.2.6 View ARec…………………………………………………………………………………..7
3.2.7 Delete All Rec……………………………………………………………………...……….7
3.3 Setup………………………………………………………………………………………..…7
3.3.1 System ………………………………………………………………………………..…….7
3.3.2 Record…………………………………………………………………………………..…..7
3.3.3 Communication…………………………………………………………………......……...7
3.3.4 Light Adjust ………………………………………………………………………….……..8
3.4 System Infor…………………………………………………………………………………..8
3.4.1 User
Reg…………………………………………………………………………………….8
3.4.2 Finger………………………………………………………………………………………..8
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
3.4.3 User Recs……………………………………………………………………………...……
8
4. Function Keys for Clocking In/Out ………………………………………….……………8
4.1 “▲” – Clock In …………………………………………………………………….………….8
4.2 “▼” – Clock Out ………………………………………………………………….…………..8
1. Basic Introduction of the Fingerprint Time attendance and Access Control
Terminal
1.1 Appearance
1.2 Technical Indicators
Item Parameter
Time Required for A Successful Confirmation < 1S
Comparison Method 1:1 or 1:N
Time Required for A Failing Confirmation < 1.2S
Confirmation Method fingerprint, password, card
User Number any number between 1 to 65535
Number of Fingerprint Inputs 3 inputs
Area of Fingerprint Input 16mm × 16mm
FAR ≤0.0001%
FRR ≤0.01%
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
Fingerprint Capacity 3000 fingerprints
Management Records 1000 entries
Attendance Records 80000 entries
Network Capacity 254 sets
Rs232 Baud Rate 38400
Rs485 Baud Rate 38400
Working Language Chinese, English, option with Spanish, French and
so on
Power Consumption <5W
Power Supply DC9V~12V 1.0A
Cubage 189*50*137mm
Weight 2 kg
Working Environment
Temperature 0-45℃
Humidity 20%-80%
1.3 Interface Definition
1.3.1 8-core plug .
The interface is for RS232 and RS485
1.3.2 Power Socket
1.4 Keyboard Description
1.4.1 Keyboard configuration
1 2 3 ESC
4 5 6 MENU
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
RS232RS485TCP/IP
ZKS Group (Shanghai)
7 8 9 ▲
⊙ 0 OK ▼
1.4.2 Keyboard Function .
ESC Exit or cancel a menu
MENU Enter into Terminal menu
OK Confirm
⊙ Switch on or off Terminal
▲ Move up the menu
▼ Move down the menu
0-9 Input numerical values
2. Equipment Connection
2.1 Communication via RS232
Note : To connect to equipment a bit far (1.5 meters away ) or multiple sets of
equipment , please use the way of RS485 for communication .
2.2 Communication via RS485 ( the distance can be as far as 1200 m )
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
2.3 RS485 Communication with Multi Sets of Fingerprint Terminals
2.4 TCP/IP Communication with Multi Sets of Fingerprint Terminals.
3. Function Setup
3.1 Menu
Pressing the key MENU is followed by a display of “ Admin? ”. At this time, person cannot
enter into the interface of menu until the manager has been identified with success , then
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
it shows on the LCD: “ Data Proc ”, “ Setup ”, “ System Infor ” optional with ▲ and ▼.
User of Fingerprint Time & Attendance Recorder:
The users include a manager and a general user.
The general user can only identify his/her own identity;
The manager is authorized to register new fingerprints and passwords, browse the
deleted or recorded data, browse the system information and set up functions.
Menu including : Data Proc + Setup + System Infor
Data Proc including : User Reg + Admin Reg + Sensitivity + Delete + View URec +
View ARec + Delete All
Setup including : System + Record + Communication + Light Adjust
System Infor including : User Reg + Finger + User Regs
3.2 Data Proc
3.2.1 User Reg
User Reg including : Finger + Card + Password + FP+Card + FP+PWD
User’s registering have five kinds of verifying methods , as above , we make an example
with registering in Finger way , choose Finger item , coming into registering new finger ,
Yes-Ok , No-ESC , and ID number will be increase by degrees automatically from 00001 ,
and every new fingerprint has to press three time when registered , and every user can
register three different fingerprints .
3.2.2 Admin Reg
Admin Reg including : Finger + Card + Password + FP+Card + FP+PWD
It has same register way as Users’ , every Admin can register three different fingerprints
too , and the Terminal has the Max 10 admin .
3.2.3 Sensitivity
Sensitivity including : Comparison + Init. 1:1 + Global 1
Admin can adjust the level of sensitivity to change the rate of verify’s precision , for
example , one user’s finger was broken in one day , so it’s difficult for him to pass the
verify when the sensitivity numerical value is high , so admin can change his sensitivity
down by Comparison , the scope for sensitivity numerical value is between 0—50 , if the
Verify Type is 1:1 , admin can adjust sensitivity numerical value in Init. 1:1 , the scope for
sensitivity numerical value is also between 0—50 , and when Verify Type is 1:1:N or 1:N ,
admin can adjust sensitivity numerical value in Global 1 , the scope for sensitivity
numerical value is also between 1—4 .
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
3.2.4 Delete
Delete including : Delete ID 0000 + Delete ID 0000-0
Admin can delete user’s information and admin’s information by this function , including
fingerprints , cards and passwords .
3.2.5 View URec
View URec including : URec ID 00000
Admin can check users’ records by this way , and check all records one by on through
▲ , ▼ or “ ok ” .
3.2.6 View ARec
View ARec including : ARec ID 00000
Admin also can check admin’s records by this way , and check all records one by on
through ▲ , ▼ or “ ok ” .
3.2.7 Delete All Rec
Delete All Rec including : Delete All Rec Delete ? + Delete All Rec Progressing
Admin can delete all records by this function , including user’s records and admin’s
records .
3.3 Setup
3.3.1 System
System including : Admin Max 5 + Language ENG + Data Format YMD + Time + Voice
Out Yes + LCD Contra 30 + Unlock 3 + Auto Off No + VerifyMode F/P/C + VerifyFunc
1:1:N + Default Setup
Admin can setup system here , Admin Max means the max of admin can be , and the
max is 10 , and Languaga , Data Format , Time , Voice and LCD Contrast can be
changed here , Unlock means how long time does it keep the Access Control door
opened , from 1 – 255 minutes , Auto Off means it will be auto off the Terminal according
to sets , from 1 to 255 minutes , usually it’s set as “NO” , for Verify Mode , it has five
modes : Fingerprint , Card , Password , F+C or F+P , Verify Function has three kinds :
1:1 , 1:N or 1:1:N , usually , it’s 1:N or 1:1:N , if it’s under 1:1 , it must be enter into
user’s ID before fingerprint or card or password ; here it can default Terminal by Default
Setup .
3.3.2 Record
Record including : ARec Alert + URec Alert + Reverify
ARec Alert has scope from 0 to 255 , if we set it as “ 255 ” , when the Terminal can only
store admin’s record less than 255 , it will be alert ; for URec Alert , it has scope from 0 to
1500 , if it’s set as “ 1500 ” , that means , when the Terminal can only store user’s record
less than 1500 , it will be alert . Reverify can be set at scope of 0 to 255 , for example , if
it’s set as “1’ , that means “ 1 minute ” , when user verify one time in 1 minute , it will be www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
OK , but if this user verify two times or more in 1 minute , the Terminal will be tell you “
Reverify ” .
3.3.3 Communication
Communication including : Device No + Baudrate + Parity + Port No + Com PWD + IP
Address + Subnet Mask + Default Gateway + RS485 COM
It’s set for communicating Terminal with PC and software . if Terminal was connected with
PC by TCP/IP , it must be keep Device No , Port No , Com PWD and IP Address on
software same as Terminal’s when connected . if Terminal was connected with PC by
RS485/RS232 , it must keep RS485 COM as “ YES ” , and Baudrate on Terminal must
be same as PC’s .
3.3.4 Light Adjust
Adjust the light of finger sensor .
3.4 System Infor
3.4.1 User Reg
User Reg shows how many users has been registered on Terminal , how many users
does it have ?
3.4.2 Finger
How many fingers does the Terminal have ?
3.4.3 User Recs
How many users’ records does the Terminal have ?
4. Function Keys for Clocking In/Out
4.1 “▲” – Clock In
When Terminal works under function keys for clocking In/Out , but not “ Shift ” within
ZKS’s software , “▲” means clock in , press key of “▲” before clocking in , meanwhile it
will be shows as status of “ in ” instead of “ auto ” in report .
4.2 “▼” – Clock Out
When Terminal works under function keys for clocking In/Out , but not “ Shift ” within
ZKS’s software , “▼” means clock out , press key of “▼” before clocking out , meanwhile
it will be shows as status of “ out ” instead of “ auto ” in report .
Frequently Asked Questions
Question 1: Are there any notes in the installation and using fingerprint terminal?
Answer: It should note the matters of the following three sides in the using of fingerprint
terminal:
1) Initialize the fingerprint terminal before using, to prevent the existence of lawless www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
fingerprint and lawless password.
2) The installation of fingerprint terminal affects its future using directly, so please the
professional personnel to install when installing and take the operation according to the
requirements of ZKS strictly, and cannot change the installation requirements and
parameters optionally.
3) Pay attention to the maintenance of Fingerprint terminal during the daily process,
to ensure that it is running in the good environment.
Question 2: Could it still verify when the Fingerprint Window is dirty?
Answer: It can work when the Fingerprint Window is dirty, but you must pay attention to
the maintenance of finger terminal and especially the fingerprint window at any time.
General speaking, please wipe the fingerprint window with the soft cloth, but note not to
use the organic solvent of viscous liquid, alcohol or oil etc.
Question 3: What about the durability of fingerprint module? How long has it been used in
normal condition?
Answer: Fingerprint terminal adopts the most advanced fingerprint module, this
fingerprint module is processed with toughened & thick glass material, of which wearable
degree is strong and normal operation life can reach up to five years.
Question 4: Fingerprint could be copied? The copied fingerprint could be used to verify?
Answer: Fingerprint picture can be copied, but the copied fingerprint picture cannot be
identified on the living fingerprint sensor, this is because the Fingerprint terminal adopts
the most advanced living fingerprint identification technology and finger sensor can verify
well only for living object fingerprint.
Question 5: Whether someone's fingerprint is the same as yours and can verify my
terminal?
Answer: No fingerprint is the same as yours, because the fingerprint is varied as different
people, even that the fingerprints of ten fingers of a person are not the same.
Question 6: What can I do if my registered finger is scratched? Can I verify freely?
Answer: If your finger is just scratched a little, it won't affect the opening function of
fingerprint, because it adopts the automatic restoring function in ZKS Fingerprint terminal,
fingerprint sensor can restore the rupture of fingerprint according to the trend of
fingerprint, so as not to affect the normal verifying of fingerprint. But the restoring function
of fingerprint cannot realize the complete restoring when the finger is scratched seriously,
so we suggest that you register one or two backup fingerprints, if your registered
fingerprint is injured, you can use the backup fingerprint to verify; if your fingers are all
injured, you can input the password or card.
Question 7: Most of others' fingerprint terminal adopt capacitance fingerprint sensor, but
ZKS fingerprint terminal adopts optics fingerprint sensor, which is better?
Answer: In current, the technology used for collecting fingerprint image is optics www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
ZKS Group (Shanghai)
technology and capacitance technology. Capacitance technology obtains the complete
fingerprint by the measurement of chip, the price of the chip is expensive, the collection
range is small, but fingerprint collection is not reliable, which causes the difficulty to the
using of users, in addition, it is easy to be interfered, whether static interference, salinity
of sweat or other swag and the abrasion of finger can make collection head be difficult to
read fingerprint. But for optics, it collects fingerprint by the reflection of light, optics
fingerprint collection head provides more reliable solution and improves the primary
optics image-capturing technology, the new optics fingerprint sensor adopts the imaging
technology with 500 DPI, which is suitable to peoples aged 6 to 80; adopt the newest
light road imaging system and increase the exoteric anti-interference ability; the surface
of fingerprint sensor uses nanometer plating film to deal with and make the fingerprint
sensor more wearable, it make the capacitance sensor be outshone as the
unquestionable character and favorable price.
www.zksgroup.com TEL: +86-21-67679389 ZKS Group FAX: +86-21-67679336ZKS Group Co., Limited & ZKS Technology Inc
FOR Factory
Guarantee Card
Product Model:
Product Serial Number:
Purchasing Date:
Purchasing Address:
Date of Installation and Acceptance:
Purchasing Organization:
Name:
Address:
Postal Code:
Telephone Number:
User shall fill out this card and mail back the stub to the manufacturer within 15 days
since installation and acceptance, our company will set up the user archive for you, so as
to take the lifelong track service for the product.
Please mail to: sales@zksgroup.com
top related