hot melt applicators series ep 48‐v (ul...
Post on 26-Apr-2018
269 Views
Preview:
TRANSCRIPT
NORDSON ENGINEERING GMBH � LÜNEBURG � GERMANY
Hot Melt ApplicatorsSeries EP 48‐V
(UL Models)
Manual P/N 7156473_06- English -
Edition 05/14
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Note
This document applies to products with the following P/Ns:
7154401
7154402
7154403
7154404
7154405
7154406
Order numberP/N = Order number for Nordson articles
NoteThis is a Nordson corporation publication which is protected by copyright. Copyright � 2009.
No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of Nordson Corporation.
The information contained in this publication is subject to change without notice.
� 2014 All rights reserved.- Translation of Original -
TrademarksAccuJet, AeroCharge, Apogee, AquaGuard, Asymtek, Automove, Autotech, Baitgun, Blue Box, Bowtie, Build‐A‐Part, CanWorks, Century, CF, CleanSleeve,CleanSpray, Color‐on‐Demand, ColorMax, Control Coat, Coolwave, Cross‐Cut, cScan+, Dage, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber,DuraPail, Dura‐Screen, Durasystem, Easy Coat, Easymove Plus, Ecodry, Econo‐Coat, e.DOT, EFD, Emerald, Encore, ESP, e stylized, ETI‐stylized, Excel 2000,Fibrijet, Fillmaster, FlexiCoat, Flexi‐Spray, Flex‐O‐Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Fulfill, GreenUV, HDLV, Heli‐flow, Helix, Horizon, HotShot, iControl, iDry, iFlow, Isocoil, Isocore, Iso‐Flo, iTRAX, JR, KB30, Kinetix, KISS, Lean Cell, Little Squirt, LogiComm, Magnastatic, March, Maverick, MEG,Meltex, Microcoat, Micromark, Micromedics, Micro‐Meter, MicroSet, Microshot, Millenium, Mini Blue, Mini Squirt, Moist‐Cure, Mountaingate, MultiScan, NexJet,No‐Drip, Nordson, Optimum, Package of Values, Paragon, PatternView, PermaFlo, PICO, PicoDot, PluraFoam, Porous Coat, PowderGrid, Powderware,Precisecoat, PRIMARC, Printplus, Prism, ProBlue, Prodigy, Pro‐Flo, Program‐A‐Bead, Program‐A‐Shot, Program‐A‐Stream, Program‐A‐Swirl, ProLink,Pro‐Meter, Pro‐Stream, RBX, Rhino, Saturn, Saturn with rings, Scoreguard, SC5, S. design stylized, Seal Sentry, Sealant Equipment & Engineering, Inc., SEEand design, See‐Flow, Select Charge, Select Coat, Select Cure, Servo‐Flo, Shot‐A‐Matic, Signature, Slautterback, Smart‐Coat, Smart‐Gun, Solder Plus,Spectrum, Speed‐Coat, Spraymelt, Spray Squirt, Super Squirt, SureBead, Sure Clean, Sure Coat, Sure‐Max, Sure Wrap, Tela‐Therm, Tip‐Seal, Tracking Plus,TRAK, Trends, Tribomatic, TrueBlue, TrueCoat, Tubesetter, Ultra, UniScan, UpTime, u‐TAH, Value Plastics, Vantage, Veritec, VersaBlue, Versa‐Coat,VersaDrum, VersaPail, Versa‐Screen, Versa‐Spray, VP Quick Fit, Walcom, Watermark, When you expect more., X‐Plane are registered trademarks - ® - ofNordson Corporation.
Accubar, Active Nozzle, Advanced Plasma Systems, AeroDeck, AeroWash, Allegro, AltaBlue, AltaSlot, Alta Spray, AquaCure, Artiste, ATS, Auto‐Flo, AutoScan,Axiom, Best Choice, BetterBook, Blue Series, Bravura, CanNeck, CanPro, Celero, Chameleon, Champion, Check Mate, ClassicBlue, Classic IX, Clean Coat,Cobalt, ContourCoat, Controlled Fiberization, Control Weave, CPX, cSelect, Cyclo‐Kinetic, DispensLink, DropCure, Dry Cure, DuraBraid, DuraCoat, e.dot+,E‐Nordson, Easy Clean, EasyOn, EasyPW, Eclipse, Equalizer, Equi=Bead, Exchange Plus, FillEasy, Fill Sentry, Flow Coat, Fluxplus, Freedom, G‐Net, G‐Site,Genius, Get Green With Blue, Gluie, Ink‐Dot, IntelliJet, iON, Iso‐Flex, iTrend, KVLP, Lacquer Cure, Maxima, Mesa, MicroFin, MicroMax, Mikros, MiniEdge,Minimeter, MonoCure, Multifil, MultiScan, Myritex, Nano, OmniScan, OptiMix, OptiStroke, Optix, Origin, Partnership+Plus, PatternJet, PatternPro, PCI,PharmaLok, Pinnacle, Plasmod, PluraMix, Powder Pilot, Powder Port, Powercure, Process Sentry, Pulse Spray, PURBlue, PURJet, PurTech, Quad Cure,Quantum, Ready Coat, RediCoat, RollVIA, Royal Blue, Select Series, Sensomatic, Shaftshield, SheetAire, Smart, Smartfil, SolidBlue, Spectral, Spectronic,SpeedKing, Spray Works, StediFlo, StediTherm, Summit, Sure Brand, SureFoam, SureMix, SureSeal, Swirl Coat, TAH, Tempus, ThruWave, TinyCure, TradePlus, Trilogy, Ultra FoamMix, UltraMax, Ultrasaver, Ultrasmart, Universal, ValueMate, Versa, Viper, Vista, WebCure, YESTECH, 2 Rings (Design) are trademarks- � - of Nordson Corporation.
Designations and trademarks stated in this document may be brands that, when used by third parties for their ownpurposes, could lead to violation of the owners' right.
Table of Contents I
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Table of Contents
Safety Instructions 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unintended Use - Examples - 1. . . . . . . . . . . . . . . . . . . . . . . . . . .Residual Risks 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Note on Manual 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Definition of Term(s) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Applicator 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Melter 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Control Module 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ID Plate 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Function 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Constant Pressure Controller 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .Heating 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overtemperature Shutdown by Thermostat 4. . . . . . . . . . . . .Adapter plate 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Illustration (Examples) 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicator Without Constant Pressure Controller 5. . . . . . . . .Applicator With Constant Pressure Controller 6. . . . . . . . . . . .
Table of ContentsII
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Installation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unpacking 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Transport 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Storage 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installing 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhausting Adhesive Vapors 7. . . . . . . . . . . . . . . . . . . . . . . . . . . .Installing Parts of Ship-with Kit 8. . . . . . . . . . . . . . . . . . . . . . . . . . .Attaching to Parent Machine 8. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicator P/N 7154405 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .All Other Applicators (Besides P/N 7154405) 8. . . . . . . . . . . .Observe when Attaching 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Parallelism and Application Thickness 9. . . . . . . . . . . . . . . . . .
Electrical Connection 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Laying Cable 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Heating Zones 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Solenoid valves 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information on New Constant Pressure Controller CPR 10. . . . . . . .Pneumatic Connection 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Control Air 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Control Modules 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Constant Pressure Controller 11. . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Heated Hose 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Using Second Open-end Wrench 12. . . . . . . . . . . . . . . . . . . . . . . .Connecting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disconnecting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Observe When Starting up the System 13. . . . . . . . . . . . . . . . . . . . . .Setting Outlet Pressure (CPR) 13. . . . . . . . . . . . . . . . . . . . . . . . . . .
Triggering with Proportional Valve 13. . . . . . . . . . . . . . . . . . . . .Bleeding 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Calibrating Application Width Display 14. . . . . . . . . . . . . . . . . . . . . . .Motorizing Application Width Adjustment 15. . . . . . . . . . . . . . . . . . . .
Operation 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Important When Using Polyurethane Application Materials (PUR) 16Triggering Solenoid Valves 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Setting Temperature 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Operating Temperature 16. . . . . . . . . . . . . . . . . . . . . . .Applying Hot Melt Adhesive 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Application Width 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Setting Application Thickness 17. . . . . . . . . . . . . . . . . . . . . . . . . . .
Daily Shutdown 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Settings Record 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents III
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Maintenance 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Relieving Pressure 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LA330‐II 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CPR 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depressurizing via Air Relief Valve 20. . . . . . . . . . . . . . . . . . . . .Depressurizing via Applicator 20. . . . . . . . . . . . . . . . . . . . . . . . .
Processing Materials 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance Table 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Visual Inspection for External Damage 22. . . . . . . . . . . . . . . . . . . . . .External Cleaning 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Purging with Cleaning Agent 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Lubricating Plan 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bleeding 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Visual Inspection 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing Constant Pressure Controller CPR 25. . . . . . . . . . . . . . . .ONLY Constant Pressure Controller LA330‐II 28. . . . . . . . . . . . . . . .
Cleaning 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disassembling Constant Pressure Controller 28. . . . . . . . . . . . . .
Filter Cartridge 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Removing Filter Cartridge 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing Filter Screen 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installing Filter Cartridge 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Record 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Troubleshooting Table 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Constant Pressure Controller CPR 34. . . . . . . . . . . . . . . . . . . . . . .
Repair 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Parts 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing Control Module 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Heater Cartridges, Temperature Sensor and Thermostat 36. . . . . .
Current Flow Diagram 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacing Sealing Cord 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Data 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data on New Pressure Controller CPR (Replaces Pressure Controller LA330-II) 39. . . . . . . . . . . . . . . . . .
Electrical Data 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .General Data 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of ContentsIV
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Applicator EP 48‐V 1
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Safety InstructionsATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
Description
Intended UseApplicators of the series EP 48‐V may be used only to apply PUR and otherhot melt adhesives commonly used in the book binding industry to glue thespines of books.
NOTE: UL conformity applies only when the melter types stated on theapplicator ID plate are used.
Any other use is considered to be unintended. Nordson will not be liable forpersonal injury and/or property damage resulting from unintended use.
Intended use includes the observance of Nordson safety instructions.Nordson recommends obtaining detailed information on the materials to beused.
Unintended Use - Examples -
The applicator may not be used under the following conditions:
� In defective condition
� When changes or modifications have been made by the customer
� In a potentially explosive atmosphere
� When hot melt adhesives not suitable for the unit are used
� When the values stated under Technical Data are not complied with.
The applicator may not be used to process the following materials:
� Explosive and flammable materials
� Erosive and corrosive materials
� Food products.
2 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Residual RisksIn the design of the unit, every measure was taken to protect personnel frompotential danger. However, some residual risks cannot be avoided.Personnel should be aware of the following:
� Risk of burns on the hot applicator: from hot adhesive and when makingadjustments
� Material fumes can be hazardous. Avoid inhalation.
� Hardened or charred material may cause the constant pressure controllerto cease functioning.
Note on Manual
� Because the unit is continuously being modified and improved, there areseveral models of the applicator. Thus illustrations in this manual maydeviate from the actual design
� There are other manuals specifically for older models of applicators in theseries EP48‐V (without UL conformity, recognized by the ID plate; alsorefer to page 2, ID Plate)
� Refer to separate document Parts List, P/N 7156338 for spare parts.
Definition of Term(s)
ApplicatorThe term application head is also used in Nordson literature.
MelterGeneral term for tank melters and bulk melters.
Control ModuleThe term module is also used in Nordson literature.
ID Plate
EP48‐V Applicator type
PN Nordson order number
Ser.No Serial number
U Operating voltage
f Operating voltage frequency
I Maximum current consumption
oper. temp. max. Maximum operating temperature
Applicator EP 48‐V 3
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
FunctionNOTE: The applicator is part of an application system. Also refer to page 5, Illustration (Examples).
The adhesive flows from a melter through a heated hose then a filter (2) andinto the applicator.
The adhesive is applied to the spine from underneath as soon as theApplication control module (6) is triggered (opened). The Retrosuctioncontrol module (5) sucks the adhesive out of the application slot (1) as soonas the application control module closes. This ensures exact adhesiveedges.
The application width can be set continuously from 1 to 60 mm.
2
5
1 3
7 6
4
Fig. 1 Example: Applicator P/N 7154401
1 Application slot
2 Filter
3 Display
4 Guide plates 5 Retrosuction control module
6 Application control module
7 Constant pressure controller
Note: Not all models have all components
4 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Constant Pressure Controller
The outlet adhesive pressure is controlled pneumatically via the constantpressure controller. The adhesive pressure or the quantity emitted can beadapted to the speed of the binder with a pattern controller (e.g. LA 404‐2)and a proportional valve.
NOTE: On models without constant pressure controller, the quantity emittedcan be adapted to the speed of the binder by adjusting the pump speed ofthe melter.
Heating
Electrical heater cartridges are used to heat the unit. The temperature iscontinuously measured by temperature sensors and regulated by electronictemperature controllers usually located in the electrical cabinet of the melter.
Overtemperature Shutdown by Thermostat
Thermostats in the filter and in the body switch off the heater at approx230 °C or 180 °C, depending on the model.
Adapter plate
An adapter plate with plug has been added to applicators P/N 7154401 and7154402 since 02/2013. Remove the plug if a pressure sensor is to beinstalled.
The screw heads for fastening the filter block and adapter plate to theconstant pressure controller are located behind the electrical equipmentcover on the filter block.
Adapter plateConstant pressure controller Filter block
Applicator EP 48‐V 5
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Illustration (Examples)
Applicator Without Constant Pressure Controller
Compressed airdry, non‐lubricatedmax. 7.5 bar
Encoder, installed inbinder
Input Encoder
Input Trigger
OutputRetrosuctioncontrol module
OutputApplicationcontrol module
ConnectionFilter
ConnectionBody Heated hose
OutputI/P converter
Signal transmitter
6 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Applicator With Constant Pressure Controller
I/Pconverter
EP 48‐V
Incremental transducer(Encoder)
Retrosuctioncontrol module
Application control module
Approx. 50 bar
6 bar
Constant pressure controller
DuraPail / DuraDrum
LA 404-2
Automatic pump control
Heated hose
Compressed airdry, non‐lubricatedmax. 7.5 bar
Input Trigger
Signal transmitter
Applicator EP 48‐V 7
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
InstallationATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
UnpackingUnpack carefully. Then check for damage caused during transport. Reusepackaging materials or dispose of properly according to local regulations.
TransportThe applicator is a high precision, valuable part. Handle very carefully!Protect the nozzle from damage.
The applicators P/N 7154402 and 7154405 are secured with washers andhexagonal nuts for transport:
Four washers and hexagonal nuts M8 (if re-used, tighten with approx. 5 Nm)
StorageDo not store outside! Protect from humidity and dust. Protect the nozzle fromdamage.
InstallingWhen installing the applicator, the following points should be observed inorder to avoid unnecessary effort later.
� Protect from humidity, vibrations, dust and drafts� Ensure access to parts relevant for maintenance and operation� When installing the unit, ensure that cables, air hoses and heated
adhesive hoses can not be bent, pinched, torn off or otherwise damaged.
Exhausting Adhesive Vapors
Ensure that adhesive vapors do not exceed the prescribed limits. Exhaustmaterial vapors if necessary. Ensure sufficient ventilation of the installationlocation.
1
8 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Installing Parts of Ship-with Kit
NOTE: Refer to separate document Parts List for an overview of the partscontained in the Ship‐with kit.
� Fasten the drip tray (1) to the applicator.
� The purpose of the other parts of the Ship‐with kit will be described asthey are needed.
Attaching to Parent Machine
Applicator P/N 7154405
A separate bracket is needed for attaching to a binder. This bracket is notincluded in the scope of the applicator delivery; it must be ordered to fit thebinder.
Screw the applicator onto the separate bracket in the parent machine.
All Other Applicators (Besides P/N 7154405)
Screw applicator to the intended place on the parent machine or the trolley.
Observe when Attaching
A. The application slot must be at a right angle to the direction of movementof the book spine.
B. The inside edge of the rear book clamp must be aligned to the immobileguide plate of the applicator.
NOTE: The fixed guide plate is on the other side of the applicator P/N7154406.
90°
With applicatorP/N 7154406
A. B.
Sensor gage
3
Applicator EP 48‐V 9
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Adjusting
Parallelism and Application Thickness
NOTE: A sensor gauge for adjusting the application thickness is containedin the Ship‐with kit and can be attached to the applicator.
To achieve even application, the applicator must be adjusted such that theapplication slot is parallel to the book spine.
A. Parallelism:
1. Release the locking screw (1).
2. Release locknuts on setting screws Radial position (2).
3. Turn setting screws Radial position to align the applicator parallel tothe book spine.
4. Tighten locknuts.
5. Tighten locking screw.
1
2
0,4 ±0.1 mm
B.A.
B. Adjusting application thickness (0.4 ± 0,1 mm):
� Applicator P/N 7154405: By adjusting the height on the separatebracket
� All others: By adjusting the height of the trolley.
NOTE: The application thickness on a book spine can be measured with theincluded measuring magnifier.
Only with applicator P/N 7154405:
A rod (3) can trigger a binder switch for a certain application width.
1 2
10 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Electrical ConnectionATTENTION: Observe voltage values found on the ID plate of the applicatorand solenoid valves.
ATTENTION: Risk of electrical shock. Failure to observe may result inpersonal injury, death, or equipment damage.
Laying Cable
ATTENTION: Ensure that cables do not touch rotating and/or hotcomponents. Do not pinch cables and check regularly for damage. Replacedamaged cables immediately!
Heating Zones
1. Connect the plugs (1, 2) to the melter electrical cabinet or to an externalelectrical cabinet.
NOTE: Normally the Filter (2) connection is attached to the receptacle onthe heated hose and a separate cable is used for the Head (1)connection.
2. Use safety clips - when available - to secure the plug connection.
Solenoid valves
Connect the solenoid valves to a pattern controller (e.g. LA 404‐2). Also referto page 5, Illustration (Examples).
NOTE: Connecting lines can be part of a special cable harness.
Information on New Constant Pressure Controller CPRThis pressure controller is designed especially for use in the applicatorEP 48‐V and replaces the constant pressure controller LA 330‐II. Onlyreplace the complete unit!
Order the service kit P/N 7193054 for replacement.
12
Applicator EP 48‐V 11
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Pneumatic ConnectionThe applicator may only be connected to pressure-controlled andconditioned compressed air.
Connecting Control Air
Use dry, regulated, nonlubricated compressed air.
NOTE: Pneumatic lines can be part of a special cable harness.
Also refer to page 5, Illustration (Examples).
Control Modules
1. Use the Y-plug (2) and a reducer (3) to link the pneumatic connections(1) to the customer's air conditioning unit.
2. Set air pressure to 6 bar / 0.6 MPa / 87 psi.
1
2
3
4
Note: The Y‐plug (2), the reducer (3) and the compressed air hose (4) are contained in the Ship‐with kit.
Constant Pressure Controller
ATTENTION: The maximum control pressure permitted is a factor of thetransmission ratio and the maximum inlet pressure of the subsequent systemcomponents. Refer to Technical Data.
1. Applicators with constant pressure controller:
a. Connect customer's air conditioning unit to the air connectionConstant pressure controller (1) via the customer's compressed aircontroller or proportional valve.
b. Adjust control air pressure for constant pressure controller asrequired (Refer to Operation, Applying Hot Melt Adhesive).
NOTE: The constant pressure controller has a transmission ratio of 10:1(material pressure / control pressure).
The outlet adhesive pressure is indicated on the pressure gauge (2).
1 2 3
12 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Connecting Heated HoseATTENTION: Hot! Risk of burns. Wear heat-protective gloves.
Using Second Open-end Wrench
Use a second open-end wrench when connecting and disconnecting theheated hose. This prevents the hose connection on the unit from turning.
Connecting
If cold material can be found in the hose connection, these components (1, 2)must be heated until the material softens (approx. 80 °C, 176 °F).
1. First connect the hose (3) electrically to the unit.
2. Heat the unit and hose to approx. 80 °C (176 °F).
3. Screw on heated hose.
Disconnecting
ATTENTION: System and material pressurized. Relieve system pressurebefore disconnecting heated hoses. Failure to observe can result in seriousburns.
ATTENTION: Hot! Risk of burns. Wear goggles and heat-protective gloves.
Refer to page 19, Relieving Pressure.
Applicator EP 48‐V 13
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Observe When Starting up the SystemNOTE: Depending on the system, the pressure controller and the connectedcomponents may be controlled automatically. Thus it is essential to refer tothe technical documentation of the system components!
For initial startup it is important to remember that the hydraulic connectionsand the pressure controller must first fill with material before controlling canoccur.
Setting Outlet Pressure (CPR)
The outlet pressure is set by applying pneumatic control pressure. The outletpressure reacts proportionally, but it is higher due to the transmission ratio.
NOTE: For correct control response, the material pressure at the inlet mustbe at least 0.5 MPa (5 bar) higher than the outlet pressure.
ATTENTION: The maximum control pressure permitted is a factor of thetransmission ratio and the maximum inlet pressure of the subsequent systemcomponents. Refer to Technical Data.
CAUTION: Risk of damage! To prevent hardened material from damagingseals, control pressure may not be applied in heated systems until thematerial has reached the setpoint temperature.
Triggering with Proportional Valve
Application of control pressure through an electro‐pneumatic proportionalvalve enables the outlet pressure to be controlled by an electrical signal. Thisis helpful in line speed-controlled application systems to adapt the adhesivequantity emitted to the web speed of the parent machine.
Both the proportional valve for run-up in the Dura series and the proportionalvalve in the Versa series provide maximum air pressure of 4 bar.
Trigger the proportional valve with at least 10 to 12 % of the maximum airpressure of 4 bar (= 100 %).
The proportional valve is not triggered until the melter is ready for operation.With older melters (only Dura), the kit 7193063 may need to be installed.
1 2
6
3
5 4
14 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Bleeding
Example: replacing filter cartridge. After replacing the filter cartridge, bleedthe applicator so trapped air can escape.
Bleed before beginning production. Refer to the sectionMaintenance/Bleeding in this manual.
Calibrating Application Width DisplayATTENTION: Hot! Risk of burns. Wear heat-protective gloves.
1. Heat applicator.
2. Use the handwheel Application width (3) to close the application slot untilthe left and right guide plates (1 and 2) touch one another.
3. Release the setscrew (4).
4. Turn the set collar (5) until the value 0000.00 appears in the displayApplication width (6).
5. Tighten the setscrew again.
Applicator EP 48‐V 15
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Motorizing Application Width AdjustmentObserve the following when mounting a motor drive in place of thehandwheel for adjusting the application width:
� Avoid radial load to the spindle
� Use the coupling:Using a coupling that can be separated (e.g. a simple claw coupling)between the motor drive and spindle makes disassembly formaintenance purposes easier (Refer to page 23, Lubricating Plan).
� Comply with these values:
ApplicatorMinimum torque
[Nm] required
Recommendedmaximum speed *
[min-1]
7154401
2
60
7154402 36
7154403 60
7154404 60
7154405 36
7154406 60
NOTE: * The recommended maximum speed is 1 mm/sec for allapplicators. Higher speeds increase wear to seals and bearingsurfaces. Since spindles of different pitches have to be used, differentspeeds result.
16 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
OperationATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
Important When Using Polyurethane ApplicationMaterials (PUR)
It is imperative that the following guidelines are complied with whenprocessing polyurethane application materials (PUR):
� Wear respiratory protection when the maximum permissibleconcentration of hazardous substances is exceeded.
� Before prolonged standstill of the application system, purge with asuitable cleaning agent. Use only a cleaning agent recommended by thematerial manufacturer.
� Close open material connections airtight.
When the system is to cease operation for only a short time, it suffices to coatthe application slot generously with grease.
CAUTION: Use only special high‐temperature grease. Refer to page 20,Processing Materials! Any other grease may cause the PUR material tocross‐link.
Triggering Solenoid ValvesCAUTION: Trigger the solenoid valves only when the applicator is heated tooperating temperature! Seals in the application control module and theretrosuction control module can become damaged if the material is too cold.
Setting TemperatureThe procedure for setting the temperatures is described in the temperaturecontroller manual. Temperature controllers are not part of the applicator.They can be located e.g. in the electrical cabinet of the adhesive feeding unitor in a separate electrical cabinet.
Maximum Operating Temperature
Refer to ID plate, Oper.temp.max
NOTE: When setting the temperature, the temperature prescribed by the hotmelt adhesive manufacturer is decisive. The maximum operatingtemperature for the product described here and the heated systemcomponents may not be exceeded.
Nordson will grant no warranty and assume no liability for damage resultingfrom incorrect temperature settings.
+
-
1
Applicator EP 48‐V 17
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Applying Hot Melt AdhesiveFactors that have a significant influence on application quality:
� Viscosity of the adhesive (The heat effect and the duration thereofinfluence the viscosity)
� Set application width (Medium application widths have proven to requirea lower adhesive pressure than small or large application widths)
� Book spine condition.
Setting Application Width
CAUTION: The application width may be adjusted only when the applicationcontrol module is closed and the applicator is heated to operatingtemperature.
1. Set the application width to the width of the book spine + 0.5 mm:
2. Re‐adjust application width during operation if required.
Setting Application Thickness
Refer to page 9, Adjusting.
Daily ShutdownTo prevent the PUR material to be processed from hardening, open surfacesmust be coated with grease.
CAUTION: Use only special high‐temperature grease. Refer to page 20,Processing Materials. Any other grease may cause the PUR material tocross‐link.
1. If necessary, remove adhesive from nozzle with wooden or plasticspatula, or wipe off with a cloth.
2. Set the application width to approx. 10 mm.
3. Generously cover the application slot with grease.
NOTE: For extended standstill:
1. Detach the guide plates
2. Set minimum application width.
3. Generously cover the application slot with grease.
18 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Settings Record
Production information
Adhesive Manufacturer
Max. processingtemperature
Viscosity
Cleaning agent Manufacturer
Flash point
Temperatures
Applicator Setpoint
Undertemperature
Overtemperature
Filter block Setpoint
Undertemperature
Overtemperature
Notes
Form filled out by:
Name Date
1
Applicator EP 48‐V 19
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
MaintenanceATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
NOTE: Maintenance is an important preventive measure for maintainingoperating safety and extending the service life of the unit. It should never beneglected.
Relieving Pressure
ATTENTION: System and adhesive pressurized. Relieve system ofpressure before disconnecting heated hoses, applicators or e.g. applicationmodules. Failure to observe can result in serious burns.
ATTENTION: Hot! Risk of burns. Wear goggles and heat-protective gloves.
LA330‐II
1. Set the motor speed of the melter to 0 rpm; switch off motor(s).
2. Reduce control air pressure for constant pressure controller (if included)to 0 bar.
3. Open the air relief valve Filter (1) by turning with a screwdriver.
4. Close air relief valve Filter again.
closopen
1
20 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
CPR
The pressure controller can be depressurized in two ways:
Depressurizing via Air Relief Valve
1. Switch off material supply motor(s) (bulk melter, melter).
2. Reduce the control air of the pressure controller to 0 bar.
3. Hang the bleeding reservoir next to the air relief valve, or use thecustomer's drain channel.
4. Verify that the hole in the air relief valve is pointing down.
5. Slowly open the air relief valve until material escapes.
6. Close the air relief valve again as soon as no more material flows out.
7. Properly dispose of material according to local regulations.
Depressurizing via Applicator
1. Switch off material supply motor(s) (bulk melter, melter).
2. Position bleeding reservoir (1) and clamp in place lightly by adjustingapplication width. Refer to applicator manual.
3. Reduce the control air of the pressure controller to 0 bar.
4. Electrically or manually trigger the solenoid valve Application controlmodule until no more material flows out.
5. Properly dispose of material according to local regulations.
Processing Materials
High temperature grease
Tube 250 g
Cartridge 400 g
P/N 783959
P/N 402238
Caution: Do not mix this lubricant withother lubricants! If necessary, first cleangrease off of parts.
Applicator EP 48‐V 21
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Maintenance TableThe maintenance intervals are general guidelines based on experience.Depending on operating environment, production conditions and hours ofoperation, other maintenance intervals may prove necessary.
Unit part Activity Interval Refer to
Entire application system
Purge with cleaningagent
When changing adhesive, if theadhesives used cannot be mixed
Before prolonged productioninterruptions, if PUR adhesive isprocessed
Page 22
Observe adhesivemanufacturer's
instructions
Entire applicator Visual inspection Daily Page 22
External cleaning Daily Page 22
Application control module and retrosuctioncontrol module
Check performance When bleeding -
Replace When malfunction occurs Page 35
Movable parts, seals Lubricate When reassembling
Weekly, when the application widthis changed frequently
Page 23
Sealing cord Replace When adjustable mouthpiece leaks Page 37
Filter cartridge Clean or replacefilter screen ifnecessary
Approx. every 100 hours ofoperation
Page 30
Constant pressurecontroller
Visually inspect forleakage
Function check todetect poor coating
Daily Page 25
Send in leaking/defective pressure controller to Nordsonto be replaced
Page 25
Constant pressurecontroller LA330‐II
Disassemble andclean
Depending on productionconditions, approx. every sixmonths
Page 28
22 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Visual Inspection for External DamageATTENTION: When damaged parts pose a risk to the operational safety ofthe unit and/or safety of personnel, switch off the unit and have the damagedparts replaced by qualified personnel. Use only original Nordson spare parts.
External CleaningExternal cleaning prevents pollution created by production from causing theunit to malfunction.
CAUTION: Use only a cleaning agent recommended by the adhesivemanufacturer. Observe the Material Safety Data Sheet for the cleaningagent.
CAUTION: Do not damage or remove warning labels. Damaged or removedwarning labels must be replaced by new ones.
ATTENTION: Hot! Risk of burns. Wear heat-protective gloves.
Remove adhesive residue only with a cleaning agent recommended by theadhesive supplier. Heat with an air heater if necessary. Remove dust, flakesetc. with a vacuum cleaner or a soft cloth.
1. Remove adhesive residue from the nozzle promptly with a soft cloth,before it chars.
2. Remove severe and hardened residue with a wooden or plastic spatula ifnecessary.
Purging with Cleaning AgentCAUTION: Use only a cleaning agent recommended by the adhesivemanufacturer. Observe the Material Safety Data Sheet for the cleaningagent.
1. Empty the melter and fill with cleaning agent.
2. Continue as described under Bleeding. Refer to page 24, Bleeding. Feedcleaning agent until cleaning agent comes out free of adhesive residue.
3. Properly dispose of the cleaning agent according to local regulations.
NOTE: Before starting production again, flush out cleaning agent residueusing the new adhesive.
Applicator EP 48‐V 23
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Lubricating Plan
2 3 4 5
1
6 7
Fig. 2
1 Drip tray
2 Left guide plate
3 Seal
4 Right guide plate
5 Seal
6 Clamp bar
7 Mouthpiece
CAUTION: Use only special high-temperature grease! Any other greasemay cause the PUR material to cross‐link. Refer to page 20, ProcessingMaterials.
Pos. Place to lubricate Interval
1 Contact surface between drip tray and body When reassembling
4 Sliding surface between mobile guide plate and body When reassembling
Weekly, when the applicationwidth is changed frequently
Refer to page 37, ReplacingSealing Cord
3, 5 Complete seal
6, 7 Contact surface between mouthpiece and clamp bar
6 Mouthpiece bearing surface
- Screw, spindle threads When reassembling
1
1
24 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
BleedingThe applicator must be bled if air or gas penetrates the system. The sectionsFilter and Application slot must be relieved of air one after the other:
ATTENTION: Hot! Risk of burns. Wear goggles and heat-protective gloves.
1. Heat up heated system components.
2. Completely close the application slot.
3. Switch on the melter motor(s).
4. Bleeding filter section:
a. Open the air relief valve Filter (1) by turning with a screwdriver untilmaterial flows out free of bubbles.
b. Close air relief valve Filter again.
5. Bleeding application slot section
a. Position bleeding reservoir (1) and clamp in place lightly by adjustingapplication width.
b. Pressurize the constant pressure controller with control pressure andelectrically or manually trigger the solenoid valve Application controlmodule until material flows out free of bubbles.
c. Remove the bleeding reservoir.
6. If necessary, remove adhesive from nozzle with wooden or plasticspatula, or wipe off with a cloth.
7. Properly dispose of adhesive according to local regulations.
Applicator EP 48‐V 25
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Visual InspectionIf adhesive escapes between the top and bottom parts (arrow), the interiorseals are worn.
Replacing Constant Pressure Controller CPRThe replacement kit contains O‐rings and seals for the control modules (Fig. 3) and the applicator (Fig. 4).
(206090)
(250254)
1
2
(250257)3
Fig. 3
1 � O-RING 17x1.5 Viton 70 shore A black
2 � O-RING 12x2.5 VITON 70 shore A black
3 � O-RING 16x2 Viton 80 shore A black
Continued...
26 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
1
4
4
2
3
Fig. 4
1 � O‐ring 60 x 3 Viton
2 � Seal EP48-V LH
3 � Seal EP48-V RH
4 � O‐Ring 16x2.5 Viton
Applicator EP 48‐V 27
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
1. Refer to Relieving Adhesive Pressure.
2. Disconnect the applicator from the voltage supply (pull the plug).
3. Detach the heated hose.
1
2
333
4
4. Screw on the drip tray.
5. Remove the filter block electrical equipment cover (1) and release thefour screws that secure the filter block and the adapter plate* (2).
*There is an adapter plate for DuraPail/Drum systems in the kit 7178722,and for VersaPail/Drum systems in the kit 7178732.
6. Detach the old pressure controller (4).
Nordson recommends thorough cleaning, particularly of the adhesivechannels. Remove the modules for cleaning.
7. Clean the adhesive channels. If leakage is detected on the modules,replace the O-rings (Fig. 3). Follow the instructions Repair / ReplacingControl Module in the applicator manual.
8. Replace the seals (1, 2 and 3, Fig. 4). Follow the instructions Repair,Replacing Sealing Cord in the applicator manual. Clean the adhesivechannels.
Continued...
12
28 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Delivery of the new pressure controller includes, among other parts, theO-rings* (3). Always replace them.
9. Clean the O‐ring grooves.
10. Apply high temperature grease to the O-rings and ensure that they arepositioned properly in the groove.
11. When putting the electrical equipment cover back into place, verify thatthe PE line is connected and no lines are pinched.
ONLY Constant Pressure Controller LA330‐II
Cleaning
Clean format piston, socket and holes through which material passes approx.every six months, depending on production conditions. This removesmaterial residue that has hardened and could hinder motion of the formatpiston or cause blockage.
ATTENTION: Risk of explosion! Never use solvents or cleaning agentscontaining halogenated hydrocarbons! Refer to the material safety datasheet of the material to be used! Use only a cleaning agents recommendedby the hot melt material manufacturer.
CAUTION: Do not use hard or metallic tools to clean. Do not use wirebrushes! This could irreparably damage the release coating. Use only soft
aids (wooden or PTFE spatula or soft brush).
Disassembling Constant Pressure Controller
CAUTION: Before removing the format piston, verify that the assembly tool(P/N 7109640) is at hand. It is not included in the scope of the applicatordelivery and must be ordered separately.
NOTE: Refer to separate document Parts List for spare parts kits.
1. Relieve system pressure. Refer to page 19, Relieving Pressure.
2. Detach pneumatic part (1) and adapter plate (2).
Continued...
11
10
Applicator EP 48‐V 29
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
3. Extract the format piston. To extract the format piston, screw an M4screw into its face.
a. Check format piston and guide ring (8); replace if necessary
b. Always replace the sealing rings when the format piston has beenremoved. Observe the following (Refer to Fig. 5):
� Always use the assembly tool (9, P/N 7106940) to put the sealing ring(6) on the top section (3) into place, ensuring that it is positionedcorrectly.
� Guide the bottom section (4) with the seal (5) in from underneath,taking care to place is properly. Guide in the top section from above,then screw together the top and bottom sections. Otherwise the lowerseal (5) will be damaged
� Lubricate seals and guide ring with special temperature‐resistantgrease (Refer to page 20, Processing Materials), completely fillingthe groove (7).
3
4
96
3
6
5
8
7
Fig. 5
4. Check the socket bearing surface (10) and replace the socket ifnecessary. Observe the following:
� Always replace the O‐rings when the socket has been removed.Lubricate O‐rings special temperature‐resistant grease.
� Position socket correctly when inserting: Notch towards the cylinderpin (11, in the constant pressure controller).
30 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Filter CartridgeATTENTION: Hot! Risk of burns. Wear appropriate protectiveclothing/equipment.
ATTENTION: System and material pressurized. Relieve system pressure.Failure to observe can result in serious burns.
Removing Filter Cartridge
NOTE: Remove the filter cartridge only when the applicator is hot.
CAUTION: As soon as the thread is disengaged, cease turning. Otherwisepart of the filter cartridge may remain in the bore.
Replacing Filter Screen
Refer to separate document Parts List.
Installing Filter Cartridge
NOTE: Install the filter cartridge only when the applicator is hot.
1. Apply high temperature grease to all threads and O‐rings. Refer topage 20, Processing Materials.
2. Slide in the filter cartridge and tighten somewhat (approx. 1 Nm / 8.85lbin).
3. Feed material by allowing the pump to run until the material comes out ofthe applicator free of bubbles.
4. Properly dispose of material according to local regulations.
Applicator EP 48‐V 31
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Maintenance Record
Unit part Activity Date Name Date Name
Complete applicator Lubricate weekly
Filter cartridge Clean or replace filterscreen if necessary
ONLY constantpressure controllerLA330‐II
Disassemble andclean
Constant pressurecontroller CPR
Visual inspection
Replace
32 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
TroubleshootingATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
ATTENTION: Troubleshooting activities may sometimes have to be carriedout when the unit is energized. Observe all safety instructions andregulations concerning energized unit components (active parts). Failure toobserve may result in an electric shock.
Troubleshooting TableOptimal material application is only possible when all system componentswork together. Thus other system components should be examined duringtroubleshooting when the material application quality deteriorates.
The troubleshooting table serves as an aid to qualified personnel. It cannothowever replace targeted troubleshooting using e.g the wiring diagram andmeasuring instruments. It also does not include all possible problems, onlythose which most typically occur.
Problem Possible cause Corrective action Refer to
Applicator or partsthereof do not gethot
Temperature on correspondingtemperature controller setincorrectly or not at all
Adjust temperature Page 16
Plug has no contact Secure plug -
Fuses in melter or electricalcabinet defective
Disconnect unit from line voltage,check fuses and replace ifnecessary
Meltermanual,
wiring diagram
Heater cartridge(s) defective Have heater cartridge(s) checkedby qualified personnel; replace ifnecessary
-
Thermostat defective Have thermostats checked byqualified personnel; replace ifnecessary
-
Adjustablemouthpiece leaks
Cross‐linked adhesive ordamaged sealing cord aroundsliding surface betweenmouthpiece and body
Clean section, replace sealingcord
Page 37
Lubricate sliding surfaces andseals
Page 23
Continued on next page
Applicator EP 48‐V 33
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Problem Refer toCorrective actionPossible cause
No hot meltadhesive comesout of applicationslot
Applicator has not yet reachedoperating temperature
Wait until temperature has beenreached, check temperaturesetting if necessary
Page 16
Not enough adhesive in melter Fill Manual formelter
Control air not connected Connect Page 11
Melter pump is not working Check; replace if necessary Manual formelter
Application slot blocked External cleaning Page 22
Nozzle stem of application controlmodule stuck
If the nozzle stem does not movewhen triggered, the applicationcontrol module must be replaced
Page 35
Format piston in constantpressure controller is blocked
Constant pressure controllerLA330‐II maintenance
Replace constant pressurecontroller CPR
Page 28
Page 25
Adhesiveapplication is notexact
Application slot partially clogged External cleaning Page 22
Nozzle damaged Replace Parts List
Distance between applicator andbook spine not even
Adjust applicator Page 9
Application quantity and bookspine processing speed notattuned to one another
Attune process variables to oneanother by trial and error
-
Hot melt adhesive unsuitable Consult adhesive manufacturer -
Air within system Bleed Page 24
Control air pressure fluctuates onconstant pressure controller
Check compressed air controllerand proportional valve
-
Format piston in constantpressure controller is blocked
Constant pressure controllerLA330‐II maintenance
Replace constant pressurecontroller CPR
Page 28
Page 25
34 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Constant Pressure Controller CPR
Problem Possible cause Corrective action
Impaired controlcharacteristics
Hardened material residue hindersformat piston movement
Replace pressure controller (page25)
O‐ring in pneumatic section is worn
Control pressure hose obstructed(e.g. kink, leak)
Check control pressure hose
Insufficient inlet material pressure Increase inlet material pressure
Leakage Seals, O‐rings worn Replace pressure controller (page25)
Material leakage at inlet oroutlet
Damaged hydraulic connections Replace O‐rings
1
O‐ring
Applicator EP 48‐V 35
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
RepairATTENTION: Allow only qualified personnel to perform the following tasks.Observe and follow the safety instructions in this document and all otherrelated documentation.
CAUTION: Before beginning any repair work, ensure that the applicator hasbeen relieved of pressure. Refer to page 19, Relieving Pressure.
Parts
� Refer to separate document Parts List
� Comply with the lubricating plan when installing spare parts. Refer topage 23, Lubricating Plan.
Replacing Control ModuleATTENTION: Hot! Risk of burns. Wear heat-protective gloves.
CAUTION: To prevent damage to seals and nozzle stem, replace controlmodules only when the applicator is heated.
CAUTION: The application control module is attached to the body with anadapter plate (1). Do not detach the adapter plate. Otherwise the controlmodule may not be positioned correctly.
1. Electrically heat cold applicator until adhesive is liquid.
2. Relieve pressure.
3. Detach the compressed air connections.
4. Release fixing screws and replace control module.
CAUTION: Ensure that the old O-ring is removed and does not remain in theapplicator body.
5. Screw new control module into place.
6. Reconnect compressed air.
36 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Heater Cartridges, Temperature Sensor andThermostat
These parts are located behind the electrical equipment covers on the filterunit and the body.
ATTENTION: Risk of electrical shock. Before removing the electricalequipment covers, ensure that the applicator is deenergized. Failure toobserve may result in personal injury, death, or equipment damage. Whenputting an electrical equipment cover back into place, verify that the PE line isfastened to to the connection (3).
2 31
Fig. 6
1 Electrical equipment coverBody
2 Electrical equipment coverFilter Unit
3 ConnectionPE line
Current Flow Diagram
Applicator Filter Unit
1
2
1
2
Fig. 7 Current flow diagram
1 Temperature sensor 2 Heater cartridges
Note: The temperature sensor is part of the cable harness
Applicator EP 48‐V 37
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Replacing Sealing CordATTENTION: Hot! Risk of burns. Wear heat‐protective clothing, safetygoggles, and heat‐protective gloves.
NOTE: Spare parts kit required: P/N 7157143. Also refer to separatedocument Parts List.
1. Electrically heat cold applicator until adhesive is liquid.
2. Set maximum application width.
3. Remove the left and right guide plates (1 and 2) as well as the seals (6).
4. Release both screws of spindle guide (3) approx. 2 mm.
5. Remove the screws (4) and detach the clamp bar (5).
6. Pry mouthpiece (7) away from body somewhat and extract out the frontalong with the spindle and the handwheel.
7
1 2 3
456
6.3.
Continued...
38 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
7. Remove old sealing cord from the groove (8):
8
8. Clean groove and sliding surfaces on the body and mouthpiece:
CAUTION: Use only a cleaning agent recommended by the adhesivemanufacturer. Observe the Material Safety Data Sheet for thecleaning agent.
� Remove adhesive residue with cleaning agent. Heat with a hot air fanif necessary
� Remove severe and hardened residue with a wooden or plasticspatula if necessary.
9. Cut open the O‐ring (contained in the parts kit) and insert it into thegroove (8) as a sealing cord.
10. Re-assemble the parts. Observe particularly:
a. Lubricating plan, refer to page 23, Lubricating Plan.
b. Seat of both pulley keys
c. Clamp bar fastening:
� Correct order of spring washers
� Insert the screws with spring washer package all the way.
10.b. 10.c.
Applicator EP 48‐V 39
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Technical Data
Operating Data
Maximum operating temperature
Overtemperature shutdown bythermostat (P/N 7147786)
200
230
°C
°C
390
446
°F
°F
Delivered untilJune 2014
Maximum operating temperature
Overtemperature shutdown bythermostat (P/N 7173136)
170
180
°C
°C
340
356
°F
°F
Delivered beginningJuly 2014
Maximum operating air pressure 6 bar 0,6 MPa 87 psi
Maximum operating pressure(adhesive)
40 bar 4 MPa 580 psi
Maximum adhesive viscosity that canbe processed
30�000 mPas 30 Ms/m2 30�000 cP
Application width 1 to 60 mm
Max. deviation of applicationquantities
< � 5 %, depending on adhesive
Heatup time � 30 min
Data on New Pressure Controller CPR (Replaces Pressure ControllerLA330-II)
Warning: Select inlet pressure and control pressure such that the inlet pressure permitted forsubsequent system components is not exceeded!
Max. inlet pressure 4,5 MPa 45 bar 655 psi
Min. inlet pressure Desired outlet pressure + 5 bar
Permitted control pressure
(limited to max. 4 bar by triggering of melter)
0 to 0.4 MPa 0 to 4 bar 0 to 58 psi
Transmission ratio control pressure :outlet pressure
1:10
Permitted operating temperature 0 to 180 °C 32 to 356 °F
Weight Approx. 2.2 kg
40 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
Electrical Data
Operating voltage (heater) 230 VAC
Power consumption (heater) Body: 960 W
Filter: 600 W
Operating voltage (solenoid valves) 24 VDC
Power consumption (solenoid valves) Application control module: 2.5 W
Retrosuction control module: 1.8 W
General Data
Weight Approx. 45 kg
Noise emission < 70 dB(A)
Degree of protection IP 44
Applicator EP 48‐V 41
P/N 7156473_06� 2014 Nordson Corporation EP48V_UL
Dimensions
NOTE: Example: Applicator P/N 7154406. The dimensions of otherapplicators may differ slightly.
146
1 - 60 mm
app
rox.
174
approx. 456ap
pro
x. 2
06
50 50
150456480
65�14
M8 - 15 deep
app
rox.
271
42 Applicator EP 48‐V
P/N 7156473_06 � 2014 Nordson CorporationEP48V_UL
top related