how to take care of spot tuckpointing do -it-yourself · a short tutorial from harambee youth...

How To Take Care Of Spot Tuckpointing

A short tutorial from Harambee Youth Training.

Call Michelle Johnson @ 726-4988 x251 with any questions.

Clean out joints. Can be grinded, scraped or brushed out. The deeper you go, the longer the patching will last. The joints should be at least ½ inch to 1 inch deep.

Brush the joints with a MASONRY BRUSH to clear out the sand. Then spray water on the area you are working on.

Mix mortar: Buy "Type N" prewith water in bucket using a MARGIN TROWEL. It should not be too wet or too dry, it should look and feel like fluffy mashed potatoes.

Scoop mortar onto your HAWK and flatten into a pancake. Use your JOINER to take mortar from the hark and place in your wall.

Let your work dry a little. When it crumbles off, use your MASONRY BRUSH to finish your work. This is important to create a good bond with the bricks.

•If you are working on a hot day, you may need to wet down your work later in the day. If it dries too fast, it won't harden properly.

How To Take Care Of Spot Tuckpointing Do

A short tutorial from Harambee Youth Training.

4988 x251 with any questions.

Clean out joints. Can be grinded, scraped or brushed out. The deeper you go, the longer the patching will last. The joints should be at

Brush the joints with a MASONRY BRUSH to clear out the sand. Then spray water on the area you are

Mix mortar: Buy "Type N" pre-mixed mortar. Mix with water in bucket using a MARGIN TROWEL. It should not be too wet or too dry, it should look and feel like fluffy mashed potatoes.

Scoop mortar onto your HAWK and flatten into a pancake. Use your JOINER to take mortar from the hark and place in your wall.

Let your work dry a little. When it crumbles off, use your MASONRY BRUSH to finish your work. This is important to create a good bond with the bricks.

If you are working on a hot day, you may need to wet down your work later in the day. If it dries too fast, it won't harden

Do-It-Yourself

Let your work dry a little. When it crumbles off, use your MASONRY BRUSH to finish your work. This is important to create a good bond with the bricks.

If you are working on a hot day, you may need to wet down your work later in the day. If it dries too fast, it won't harden

How To Take Care Of Spot Tuckpointing

A short tutorial from Harambee Youth Training.

Call Michelle Johnson @ 726-4988 x251 with any questions.

Tool List: These tools should be easy to find at any hardware store if you ask for help. If you clean them

use them, they should last a very long time! Tools can be cleaned with water, or also with a wire brush.

TOTAL: Under $40!Depending on how many bags of mortar you need, you should be spending less than $40! Not bad for a repair

that could save you a lot more!!

These prices are averages, and depending on where you go, you might find these tools more or less expensive. Also,

you might find scraping out the joints to be difficult without proper tools. Masonry rakes can be very help

expensive at about $40 a piece. A grinder with a diamond blade is also expensive, but you might be able to ask about

renting these items.

Masonry Brush

Bag of 'Type N' Mortar

How To Take Care Of Spot Tuckpointing Do

A short tutorial from Harambee Youth Training.

4988 x251 with any questions.

These tools should be easy to find at any hardware store if you ask for help. If you clean them

use them, they should last a very long time! Tools can be cleaned with water, or also with a wire brush.

TOTAL: Under $40! Depending on how many bags of mortar you need, you should be spending less than $40! Not bad for a repair

These prices are averages, and depending on where you go, you might find these tools more or less expensive. Also,

you might find scraping out the joints to be difficult without proper tools. Masonry rakes can be very help

expensive at about $40 a piece. A grinder with a diamond blade is also expensive, but you might be able to ask about

Margin Trowel

Bucket

Jointer Hawk

Do-It-Yourself

These tools should be easy to find at any hardware store if you ask for help. If you clean them well after you

use them, they should last a very long time! Tools can be cleaned with water, or also with a wire brush.

Depending on how many bags of mortar you need, you should be spending less than $40! Not bad for a repair

These prices are averages, and depending on where you go, you might find these tools more or less expensive. Also,

you might find scraping out the joints to be difficult without proper tools. Masonry rakes can be very helpful, but are

expensive at about $40 a piece. A grinder with a diamond blade is also expensive, but you might be able to ask about

Bucket

Hawk