hybrid racing z3 k-swap shifter install guide
Post on 05-Apr-2018
227 Views
Preview:
TRANSCRIPT
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
1/8
1
Install Guide forZ3 K-Swap Shifter
Features:
Friction reducing and wear-compensating center pivotpoint.
Anodized aluminum front and side rockers
Independently adjustable front/back and left/rightthrow which can be set between 85% and 45% of theOEM 8th Gen Civic shifter.
Adjustable shift knob height and position.
Rubber seal to keep out road noise, debris, and ex-haust heat
Package Contents:
(1) Short shifter assembly with aluminum dust shield
(4) M8 allen bolts with washers
(1) Hybrid Racing shifter cable bracket
(1) OEM shifter cable bracket
(1) Rubber gasket
(3) M6 allen bolts with washers
This product may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actualor incidental expense attributed to the use of any performance parts sold by Hybrid Racing LLC. Purchasers
agree to all of the terms of this agreement upon the purchase of parts.
Important!! Please read the entire install guide twice before starting your instal-lation. No, really its a good idea to read it twice before you begin so everything
goes smooth ;)
Recommend Tools:
Drill with 3/8 drill bit
3mm, 4mm, 5mm, 6mmallen wrench
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
2/8
2
Install GuideSTEP 1:Using a 3mm allen wrench re-move the (4) M4 bolts securingthe aluminum dust cover to the
shifter assembly.
STEP 2:Insert the shifter assembly fromthe bottom and with a 6mm allenwrench, secure it to the centertunnel on the rear side with (2) ofthe supplied M8 bolts as shownin FIG 2.
STEP 3:
Once the shifter assembly is heldsnug in the center tunnel, push itup flat against the car and markthe center of the holes for the (2)front mounting bolts as illustratedin FIG 3.
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
3/8
3
STEP 6:Install the shifter assembly withthe rubber gasket installed backinto the center tunnel as you didin step 2 as shown in FIG 6.Loosely thread the (2) M8 boltsin, do not tighten yet.
STEP 5:Place the rubber gasket atop theshifter assembly and secure it tothe baseplate with the (4) plasticpush-in rivets. If your shifter ap-pears as the one in FIG 5 youare ready to .
Install GuideSTEP 4:Remove the shifter assembly,then using a drill with 3/8 drill bit,drill a hole at the two marks you
made. (May be a good idea todrill with an 1/8 drill bit for a pilothole first)
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
4/8
4
STEP 7:With the same 6mm allen
wrench, go inside of the car to
install the (2) M8 bolts that hold
the front of the shifter assemblyup. Since the shifter is loosely
mounted from the bottom, grab
the shifter arm to pull up on the
assembly and line the holes up
as shown in FIG 7. Once you
have them both threaded in,
tighten them down.
Install Guide
Cable Selection
The next section of this install guide includes the installation of the cables. Before youcan install cables you need to decide which cables you are going to use, OEM or Hy-brid Racing. Once you have chosen which cables you would like to use you can moveon to step 9.
STEP 8:Go back under the car and usinga 6mm allen wrench again, tight-en the (2) rear mounting bolts. Ifyours appears as the one in FIG8 it ready to have the cables in-stalled.
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
5/8
5
OEM Cable InstallSTEP 9A:Locate the OEM cable keeper in
the bag of hardware that came
with the shifter. You need the one
shown in FIG 9A.
STEP 9B:Starting with the lower cable
shown in FIG 9B,snap the
endlinks onto the rocker arms
and then slide shifter cable bases
into grooves of the base. (NOTE:
These steps should be done with
the shifter attached to the car,these pictures are shown off of
the car for better reference)
STEP 9C:Slide the OEM cable keeper over
the cable bases and using a4mm allen wrench thread in and
tighten the (2) M6 bolts as illus-
trated in FIG 9C.
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
6/8
6
Hybrid Racing Cable InstallSTEP 9A:Locate the Hybrid Racing cable
keeper in the bag of hardware
that came with the shifter. You
need the one shown in FIG 9A.
STEP 9B:Starting with the lower cable
shown in FIG 9B,snap the
endlinks onto the rocker arms
and then pull back on the cables
and place the cable bases in the
corresponding holes. (NOTE:
These steps should be done withthe shifter attached to the car,
these pictures are shown off of
the car for better reference)
STEP 9C:Slide the Hybrid Racing cable
keeper into the grooves of thecable bases and using a 4mm al-
len wrench thread in and tighten
the (3) M6 bolts as illustrated in
FIG 9C.
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
7/8
7
Install Guide
STEP 11:Slide the offset onto the lower shifting
arm, rotate it to your desired position,
tighten the lower offset bolt with a
5mm wrench as shown in FIG 11A.
Also, place the upper shifter rod to the
desired position and tighten the upper
offset bolt with a 5mm allen wrench.
STEP 10:Using a 3mm allen wrench and the (4)
M4 bolts you removed in step 1, secure
the dust shield to the shifter assembly.Once you have done this and you shift-
er appears as the one in FIG 10, you
are ready to move into the interior of
the car.
STEP 12:Thread your shift knob onto the upper shift rod, and lock into position by tightening
the binding nut with a 17mm wrench as shown in FIG 12A. Once you are done with
the shift knob your installed shifter should appear as the one in FIG 12B.
-
8/2/2019 Hybrid Racing Z3 K-Swap Shifter Install Guide
8/8
8
If you have any questions or comments, please email support atsupport@hybrid-racing.com
Legal DisclaimerUsers assume all cost and risk associated with these or any other items purchasedfrom Hybrid Racing LLC.
Parts sold or manufactured by Hybrid Racing LLC may not meet legal requirements foruse on public roads. People thinking about purchasing product(s) from Hybrid RacingLLC should check with their local and state authorities for legality. It is the users re-sponsibility to know and comply with all local and federal laws and regulations. Use orinstallation of Hybrid Racing LLC products may affect user insurance and/or vehiclewarranty coverage. It is the users sole responsibility for consequences that may occurdue to having the product installed in his/her vehicle.
Hybrid Racing LLC assumes no legal responsibilities and/or liabilities, whether to us-ers vehicle, engine, person(s), and/or property(s), that result from the use of, or servic-ing of a vehicle of which a Hybrid Racing LLC product has been installed/attempted tobe installed, or to any other vehicle(s) and/or person(s), regardless of whether or notthis product has any involvementdirectly or indirectly and/or liability, and/or whether or not proper installation has beencarried forth.
All engines, engine parts and electrical components are for OFF ROAD USE ONLY/RACINGVEHICLES ONLY. They are not for or to be used on public roads in the USA.
Acquisition of a Hybrid Racing LLC product will act as an acknowledgement of the le-gal disclaimer stated herein.
Hybrid Racing LLC reserves the right to change this disclaimer at any time without anypriorconsent or notification.
Should you need to contact us our details are as follows: Hybrid Racing LLC, 12231 Industriplex Suite B, Baton Rouge, LA 70809
www.hybrid-racing.com
top related