records.garfield-county.com€¦ · i garfield county building & planning department 108 8th...
Post on 19-Apr-2020
5 Views
Preview:
TRANSCRIPT
I
Garfield County Building & Planning Department
108 8th Street, Suite#401 Glenwood Springs, Co. 81601 Office:970·945·8212 Fu: 970-384-3470
Inspection Line: 970·384-5003
Building Permit No. 11223
Parcel No:
Locality:
Job Address: ·---···-------- 270~t:;Jear C[(lek Rd, De~eque
Use of Building: ______________ L.iquid Separator Ski9_Building _____ _
Owner:
Contractor:
Fees:
Clerk:
Plan Check:
Bldg Permit:
Chevron USA ----·---------···
Elkhorn Construction Inc
$ 81.41
125.25
Septic:
other Fees:
Total Fees: $ 206.66 ·-·~-----·~·"--
Date: 2/4/2008 I
D
GARFIELD COUNTY BUILDING PERMIT APPLICATION 108 8" Stree~ Suite 401, Glenwood Springs, Co 81601
Phone: 970-945-82121 Fax: 970-384-3470 I Inspection Line: 970-384-5003 www.garfield-county.com
at the assessors office 970-945-9134)
of modular unit, and utility hookups
D
~ This application for a Building Pennit must be signed by the Owner of the property, described above, or an authorized agenl If the signature below is not that of the Owner, a separate lener of authority, signed by the Owner, must be provided with this Application.
I .ega! As.cess. A Building Permit cannot be issued without proof of legal and adequate access to the property for purposes of inspections by the Building Department Other Permits. Multiple separate pl}nnits may be required: (1) State Electrical Pennit, (2) County ISDS Permit, (3) another permit required for use on the property identified above, e.g. State or
County Highway/ Road Access or a State Wastewater Discharge Permit. Void Permit A Building Pennit becomes null and void if the work authorized is not oonuneneed within 180 days of the date ofissuance and if work is suspended or abandoned for a period of 180
days after cmrnnencement. CERTIFICATION
I hereby certify that I have read this Application and that the information contained above is true and comx:t. I understand that the Building Department accepts the Application, along with the plans and specifications and other data submitted by me or on my behalf (submittals), based upon my certification as to ae<:uracy, Assuming completeness of the submittals and approval of this Application, a Building Permit wiU bll issued granting permission to me, as Owner, to construct the structure(s) and facilities detailed on the submittals reviewed by the BW!ding Depamnent. In consideration of the issuance of the Building Permit, I agree that land my agents will comply with provisions of any federal, state or lo<lallaw regulating the work and the Garfield County Building Code, ISDS regulations and applicable land use regulations {County Regulation(s)). I acknowledge that the Building Permit may be suspended or revoked. upon notice from the County, if the location, construction or use of the structure{s) and facility(ies), described above, are not in compliance with County Regulation(s) or any other applicable law. I hereby grant permission to the Buildmg Department to enter the property, described above, to inspect the work. I further acknowledge that the issuance of the Building Permit does not prevent the Building Official from: (1) requiring the correction of errors in the submittals, if any, discovered after issuance; or (2) stopping construction or use of the structure{s) or fucility(ies) if such is in violation of County Regulation(s) or any other applicable law. Review of this Application, including submittals, and inspections of the work by lhe Building Department do not constitute an acceptance ofresponsibility or liability by the CQunty ofen:ors, Qmissions or discrepancies. As the Owner, I acknowledge that responsibility for compliance with federal, state and local laws and County Regulations rest with me and my authorized agents, including without limitation my architect designer, engineer and/ or builder. I HEREBY ACKNOWLEDGE TIIAT I HAVE READ AND UNDERSTAND THE NOTICE & CERTIFICATION ABOVE:
Special Conditions:
Adjusted Valuation: Plan Check Fee: Permit Fee: Manu home Fee: Mise Fees:
5i::J4o.ao 81.1 i {25-25 ISDSFee: Total Fees:
2-ew.&6 Egbfj _3({? k'3"q~:; (J) I!J ~~~:
~ & Issued Date:
Setbacks: OCCGroup: ConstType: Zoning:
BL\\{EPT: ~ ~ PLNGDEPT: <
lj 0()!_ WfYj_ ~\~~~\ 1/~(.~ APPRo'#fff"\-.~ ~~~\ DATE APPROV ' DATE
l0;_0( - ·~ ~d'/'-~.12
VALUATION FEE DETERMINATION
Applicant Address Date
Chevron U.S.A. Inc. Subdivision 2700 Clear Creek Road, De Beque, CO Lot/Block _____________ Contractor
Finished {1ivable Area}: Main sq. It
Upper sq. It
Lower sq.ft
Other sq.ft X $74.68
Total Square Feet 0 sq.ft Valuation
Basement: Unfinished sq.lt X $41.00 Conversion of Unfinished to Finished sq. It X $33.68
Total Valuation
Garage: sq.ftX $18.00
Carport: sq.ft X $12.00
Total Valuation
Crawl Space sq. It X $9.00
Total Valuation
Decks/ Patios Covered sq.ftX $24.00
Open sq.ft X $12.00
Total Valuation
Commercial Type of Construction:
Occupancy: Modular set fee 560 sf X $9.00
sf X sf X sf X sf X sf X
Valuation
Total Valuation
Liquid Separator Building
0.00
0.00
0.00
0.00
0.00
5,040.00
5,040.00
GARFIELD COUNTY BUILDING AND PLANNING 970-945-8212
MINIMUM APPLICATION REQUIREMENTS FOR
CONSTRUCTION OF COMMERCIAL OR MULTI-FAMILY RESIDENTIAL BUILDINGS
Including NEW CONSTRUCTION
ADDITIONS ALTERATIONS
And MOVED BUILDINGS
Ref: Chevron Central Production Facility- Liquid Separator Skid
In order to understand the scope of the work intended under a permit application and expedite the issuance of a permit it is important that complete information be provided. When reviewing a plan and it's discovered that required information has not been provided by the applicant, this will result in the delay of the permit issuance and in proceeding with building construction. The owner or contractor shall be required to provide this information before the plan review can proceed. Other plans that are in line for review may be given attention before the new information may be reviewed after it has been provided to the Building Department.
Please review this document to determine if you have enough information to design your project and provide adequate information to facilitate a plan review. Also, please consider using a design professional for assistance in your design and a construction professional for construction of your project. Any project with more than ten (10) occupants requires the plans to be sealed by a Colorado Registered Design Professional.
To provide for a more understandable plan and in order to determine compliance with the building, plumbing and mechanical codes, applicants are requested to review the following checklist prior to and during design.
Plans to be included for a Building Permit must be on draft paper at least 18"x 24'"' and drawn to scale.
Plans must include a floor plan, a concrete footing and foundation plan, elevations all sides with decks, balcony steps, hand rails and guard rails, windows and doors, including the finish grade and original grade line. A section showing in detail, from the bottom of the footing to the top of the roof, including re-bar, anchor bolts, pressure treated plates, floor joists, wall studs and spacing, insulation, sheeting, house-rap, (which is required), siding or any approved building material. Engineered foundations may be required. Check with the Building Department.
A window schedule. A door schedule. A floor framing plan, a roofing framing plan, roof must be designed to withstand a 40 pound per square foot up to 7,000 feet in elevation, a 90 M.P.H. windspeed, wind exposure B or C, and a 36 inch frost depth.
All sheets need to be identified by number and indexed. All of the above requirements must be met or your plans will be returned.
All plans submitted must be incompliance with the 2003 IBC, IPC, IMC and IFGC.
Applicants are required to indicate appropriately and to submit completed checklist at time of application for a permit:
1. Is a site plan included that identifies the location of the proposed structure, additions or other buildings, setback easements, and utility easements showing distances to the property lines from each corner of the proposed structure prepared by a licensed surveyor and has the surveyors signature and professional stamp on the drawing? Slopes of 30% or more on properties must be show on site plan. (NOTE: Section 106.2) Any site plan for the placement of any portion of a structure within 50 ft. of a property line and not within a previously surveyed building envelope on a subdivision final plat shall be prepared by a licensed surveyor and have the surveyors signature and professional stamp on the drawing. Any structure to be built within a building envelope of a lot shown on a recorded subdivision plat, shall include a copy of the building envelope as it is shown on the final plat with the proposed structure located within the envelope. Yes x
2. Does the site plan when applicable include the location of the I.S.D.S. (Individual Sewage Disposal System) and distances to the property lines, wells (on subject property and adjacent properties), streams or water courses? This information must be certified by a licensed surveyor with their signature and professional stamp on the design. Yes No X Not necessary for this proj· ect --- ISDS will be permitted with
permanent restroom bu1!dmg
3. Does the site plan indicate the location and direction of the State, County or private road accessing the property? Yes x
4. Is the I.S.D.S. (Individual Sewage Disposal System) designed, stamped and signed by a Colorado Registered Engineer?
2
Yes __ _ No Not necessary for this project X 1808 wilt be permitted with permanent restroom building
5. Are the plans submitted for application review construction drawings and not drawings that are stamped or marked identifYing them as "Not for construction, for permit issuance only", "Approval drawings only", "For permit issuance only" or similar language? Yes x No__ Not necessary for this project __ _
6. Do the plans include a foundation plan indicating the size, location and spacing of all reinforcing steel in accordance with the uniform building code or per stamped engineered design? Yes x No Not necessary for this project __
7. If the building is a pre-engineered structure, is there a stamped, signed engineered foundation plan for this building? Yes_x_ No__ Not necessary for this project __
8. Do the plans indicate the location and size of ventilation openings for under floor crawl spaces and the clearances required between wood and earth? Yes__ No__ Not necessary for project_x_
9. Do the plans indicate the size and location of the ventilation openings for the attic, roof joist spaces and soffits? Yes__ No__ Not necessary for this project_x_
10. Do the plans include design loads as required under the IBC or IRC for roof snowloads, (a minimum of 40 pounds per square foot in Garfield County)? Yes_x_ No__ Not necessary for this project __
II. Do the plans include design loads as required for floor loads under the IBC or IRC? Yes_x_ No__ Not necessary for this project __
12. Does the plan include a building section drawing indicating foundation, wall, floor, and roof construction? Yes_x_ No__ Not necessary for this project __
13. Is the wind speed and exposure design included in the plan? Yes_x_ No__ Not necessary for this project __
14. Does the building section drawing include size and spacing of floor joists, wall studs, ceiling joists, roof rafters or joists or trusses? Yes_x_ No__ Not necessary for this project __
15. Does the building section drawing or other detail include the method of positive connection of all columns and beams? Yes x No Not necessary for this project __
3
16. Does the elevation plan indicate the height of the building or proposed addition from the undisturbed grade to the midpoint between tbe ridge and eave of a gable or shed roof or the top of a flat roof? (Check applicable zone district for building height maximum) Yes_x_ No__ Not necessary for this project __
17. Does the plan include any stove or zero clearance fireplace planned for installation including make and model and Colorado Phase II certifications or Phase II EPA certification? Yes No Not necessary for this project_X_
18. Does the plan include a masonry fireplace including a fireplace section indicating design to comply with the IBC or IRC? Yes__ No__ Not necessary for this project_x_
19. Does the plan include a window schedule or other verification that egress/rescue windows from sleeping rooms and/or basements comply with the requirements of the IBCoriRC?
20.
21.
22.
23.
24.
25.
Yes No Not necessary for this project_x_
Does the plan include a window schedule or other verification that windows provide natural light and ventilation for all habitable rooms? Yes__ No__ Not necessary for this project_x_
Do tbe plans indicate the location of glazing subject to human impact such as glass doors, glazing immediately adjacent to such doors; glazing adjacent to any surface normally used as a walking surface; sliding glass doors; fixed glass panels; shower doors and tub enclosures and specify safety glazing for these areas? Yes__ No__ Not necessary for this project_x_
Do the plans include a complete design for all mechanical systems planned for installation in this building? Yes_x_ No Not necessary for this project. __ _
Have all areas in the building been accurately identified for the intended use? (Occupancy as identified in the IBC Chapter 3) Yes_x_ No__ Not necessary for this project. __ _
Does the plan indicate the quantity, form, use and storage of any hazardous materials that may be in use in this building? Yes_x_ No__ Not necessary for tbis project __ Is the location of all natural and liquid petroleum gas furnaces, boilers and water heaters indicated on the plan? Yes x No -- --
2 - Natural gas catalytic heaters Not necessary for this project __
4
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
Do the plans indicate the location and dimension of restroom facilities and if more than four employees and both sexes are employed, facilities for both sexes? Yes No Not necessary for this grflj~et x Restrooms located at separate facility -- -- Uillng
Do the plans indicate that restrooms and access to the building are handicapped accessible? Yes No Not necessary for this ~rej8Gt x
wlamg Restrooms located at separate facility
Have two (2) complete sets of construction drawings been submitted with the application? Yes x No __
Have you designed or had this plan designed while considering building and other construction code requirements? Yes_x_ No__ Not necessary for this project __
Does the plan accurately indicate what you intend to construct and what will receive a final inspection by the Garfield County Building Department? Yes_x_ No __
Do your plans comply with all zoning rules and regulations in the County related to your zone district? For comer lots see supplemental section 5.05.03 in the Garfield County Zoning Resolution for setbacks. Yes x No __ _
Do you understand that approval for design and/or construction changes are required prior to the implementation of these changes? Yes x No -- --
Do you understand that the Building Department will collect a "Plan Review" fee from you at the time of application and that you will be required to pay the "Permit" fee as well as any "Septic System" or "Road Impact" fees required, at the time you pick up your building permit? Yes_x_ No __
Are you aware that you are required to call for all inspections required under the IBC including approval on a final inspection prior to receiving a Certificate of Occupancy and occupancy of the building? Yes_x_ No __ Are you aware that the Permit Application must be signed by the Owner or a written authority be given for an Agent and that the party responsible for the project must comply with the Uniform Codes? Yes x No -- --
5
36. Are you aware that you must call in for an inspection by 3:30 tbe business day before the requested inspection in order to receive it the following business day? Inspections will be made between 7:30a.m. and 3:30p.m. Monday through Friday. Inspections are to be called in to 384-5003.
37. Are you aware that requesting inspections on work that is not ready or not accessible will result in a $50.00 re-inspection fee? Yes_x_ No ___ _
38. Are you aware that prior to issuance of a building permit you are required to show proof of a driveway access permit or obtain a statement from the Garfield County Road & Bridge Department stating one is not necessary? You can contact the Road & Bridge Department at 625-8601. Yes x No ___ _
39. Do you understand that you will be required to hire a State of Colorado Licensed Electrician and Plumber to perform installations and hookups? The license number will be required at time of inspection. Yes x No ___ _
40. Are you aware, that on the front of the building permit application you will need to fill in the Parcell Schedule Number for the lot you are applying for this permit on prior to submittal of the building permit application? Your attention in this is appreciated. Yes x No ___ _
41. Do you know that the local fire district may require you to submit plans for their review of fire safety issues? Yes x No (Please check with the building department about this requirement)
42. Do you understand that if you are planning on doing any excavating or grading to the property prior to issuance of a building permit that you will be required to obtain a grading permit? Yes x
43. Did an Architect seal the plans for your commercial project? State Law requires any commercial project with occupancy of more than 10 persons as per Section 1004 of the IBC to prepare the plans and specifications for the project. Yes No Not Necessary for this project __ x __ _
I hereby acknowledge that I have read, understand, and answered these questions to the best of my ability.
6
Signature./;~ f--. dw~ Date I /r:; /o 9 '4
Phone:.z'B'I-$"2'/- 715:;-(days); 2'3'/-77 fo- 12 95"" (evenings)
Project Name: Chevron Piceance Basin Natural Gas Development Program
Project Address: 2700 Clear Creek Road, P.O. Box 296, De Beque, CO 81630
Note:
If you answered "No" on any of these questions you may be required to provide this information at the request of the Building Official prior to beginning the plan review process. Delays in issuing the permit are to be expected. Work may not proceed without the issuance of the permit.
*If you have answered "Not necessary for this project" on any of the questions and it is determined by the Building Official that the information is necessary to review the application and plans to determine minimum compliance with the adopted codes, please expect the following:
A. The application may be placed behind more recent applications for building permits in the review process and not reviewed until required information has been provided and the application rotates again to first position for review.
B. Delay in issuance of the permit.
C. Delay in proceeding with construction.
*If you answered "No" to this question the circumstances described in the question could result in a "Stop Work Order" being issued or a "Certificate of Occupancy" not being issued.
Bpcomm October 2006
7
August 29, 2007
Mr. Fred Jartnan, Director Garfield County Building; & Plamung Department 108 gth Street, Suite 40.1 Glenwood Springs, CO 81601
Re: Authorization to. Represent Chevron-
Ja.tnes S~. Talbot Senior CoUns·el
Sally Cuffin, Washington Group International Inc.
Deat Mr, Bean:
law Department North America ExJ)Ioratitiil and Produ<;tion Company 11111 S. Wilcrest #N2Q06 Houston, Texas 77099·4397 Tel 281·561·3536 Fax 281·561·3515 jta!bot@chevron.com
Chevron U.S.A. Inc, (Chevron) has retained the services ofSally Cuffrt1 of the Washington Group International Inc.. Ms. Cuffin will represent Chevron in facility pertnitting for our Piceance Project in Garfield County, a role in which she will prepare and submit Special Use Pertnit Applications, ISDS, building, grading, pipeli11e, road crossing and other rl)utine construction related applications and infortnation on behalf of Chevron. Ms. Cuffin is also. authorized to participate in dis.cussions b.t1fore appointed and elected boards regarding; the vmious applications, however at such meetings, her authority to legally bind Chevron is limited to the tem1s set forth in the Pennit Applications or other written documents filed on our behalf.
Sincerely,
cc: Nicole Jo!mson Timothy Barrett Sally Cuffin
From:
To:
CC:
Subject:
Date:
Attachments:
Jake Mall
Cuffin, Sally;
RE: Driveway permit exemption
Thursday, November 06, 2008 1:25:38 PM
Sally: you are exempt from the driveway access permit requirement for this project. Jake
-----Original Message-----From: Cuffin, Sally <Sally.Cuffin@wgint.com> Sent: Thursday, November 06,2008 12:48 PM To: jmall@garfield-county.com <jmall@garfield-county.com> Subject: Driveway permit exemption
Jake,
I just realized that I never got an official driveway exemption email from you for buildings at Chevron's Central Production Facility. The facility is located about 2.5 miles north of the end of CR 211 (near the confluence ofT om Creek and Clear Creek).
Let me know if you have questions.
Thanks!
Sally Cuffin
(303) 843-2219
(303) 526-6514 (cell)
No. ----------~11~2~2~3~--- Assessor's Parcel No. 2139-163-00-014.
Date 2/4/2009
rl:U.IU .. DBNC!l PERMIT CARD
Job Address __ _,2...,7_,0"'-0-"c"'le""a,_r_,c""'re"-'e'-"k'-'r_,d.._. ""'D"'e B,.,;e!i<.!qot>u..,e,__ ___ ___c. ____________________ _
Owner Chevron USA Address 11118. Wilcrest dr, Houston Phl>4:l~# 281-561-4991
Contractor Elkhorn Constrution Address 2181 45 1/2 rd, De Begue PI!PbmJl # 970-283-1009
Setbacks: Front _____ Rear _____ RH _____ LH _____ Zoning _____ __
Liquid separator skid building
Soils Test -.....,.---.-7'1----::---;;:----:-----Footing :2,./?J::~~ Foundation i-J:0-d.(.Jfih1 Grout __ ...__ _________ ___
Underground Plumbing ------Rough Plumbing ----------Framing ____________ _
Insulation ---------------Roofing---------------,-----Drywall ____________ _
Gas Piping--------------
INSPECTIONS
NOTES
Weatherproofing ___________ _ Mechanical _______________ _
Electrical Rough (State) --;;;r--.,.,.--,--;..-:-:;.------Eiectrical Final (State) 2-fi'-!o(;df._ Final .2.d1--IO /Checklist CollJ.p~teci/ /Oii.( Certificate Occupancy# (/i4:j_b .
Date ISSUBO 2· N•lD ' Septic System # _________________ _
Date --------------Final ____________ _
Other ----------------:-------
(continue on back)
UIL INGP GARFIELD COUNTY, COLORADO
INSPECTION WilL NOT B!E MADE UNI!..ESS HilS CI\RD IS POSTED ON THE JOB
IT
Date Issued ~..:=-"""_4,_~_0_Cf_._ _______ PermitNo.__/_~-------AGREEMENT
In consideration of the issuance of the permit/ the applicant hereby agrees to comply with all laws and regulations related to the zoning, location; construction and erection of the proposed structured for which this permit is
granted, and further agrees that if the above said regulations are not fully complied with in the zoning/ location, erection and construction of the above described structure, the permit may then be revoked by notice from the
County Building department and IMMEDIATELY BECOME NULL AND VOID.
Use_~(/IY4"d S~'D'Jlir "S141el I!1_M,.U..,d=~~----------Address or Legal DescriptionAW cJt:(Jf" C~/it (t:lf I ~IJ!:.f!i""-=lfe.-"'---=-------
Owner CJJ~t,.ctPJ..,'fJt,.,IJ'""t1'-'-""~'!""-'"-------- Contractor 7i/Jt !txJlf)..,__.~,._,~""'-"""'-'6"-----Building PermitType _ _.UfJ""""Ifi."""'IIYJ"'"'-~"".....,=•lb',_/,"'---------------------
This Card Must Be Posted So It Is Plainly Visible From The Street Until Final Inspection
INSPECTION RECORD Footing
?~ ok Driveway
2•11-0"f IOrvL Foundation I Grouting Insulation
;2 -)-o -o9i?m Underground Plumbing Drywall
Rough Plumbing Electric FhraO)I (by State Inspector)
{Prior to Final) J- ?f-tO fly
Rough Mechanical Septic Final
Gas Piping FINAL
M1l1 J_- I 1-10
Electric Rough (by State inspector) {You Must Call For Final Inspection)
(Prior to Framing) Notes
Framing
(to include Roof in place & Windows & Doors installed & Firestopping in place)
THIS PERMIT IS NOT TRANSFERABLE For Inspection Call970-384-5003 Ofiice 970-945-8212
1 08 8~h Street, Suite 401 Gienwood SprnngsT Colorado 81601
DO NOT DESTROY THIS CAR~D
· By TJoN~~tJ, !!J!r PROTECT PERMIT FROM WEATHER AMA
(DO NOT LAMINATE)
2
3
4
5
6
. 7
CHEVRON PRODUCTION FACILITY PICEANCE BASIN DEVELOPMENT GARFIELD COUNTY, COLORADO
LIQUID SEPARATOR SKID BLDG. MBD-1075 (PRE-FABRICATED BUILDING CONSTRUCTED BY J. W WILLIAMS)
RIO BLANCO COUNTY
I L -- ~~1te-~- . ~ Township SS Range 98W Section \ ,_.1 i\\ ::::1! .-..... ~----->......
Rifle Sill
GARFIELD COUNTY
New Castle II
lw L --~~) Parachute 1 a
C):INITY MAP
r
DeBeque Exit 62
MES_A_----------- _j;::) COUNTY PITKIN COUNTY
~
' ... "' '
"-sEE VENDOR DRAWINGS FOR PRE-FAB BUilDING~ ~
FOR STAIR AND HANDRAIL DETAILS~ SEE OWG. 2033-30-Cl-1109-XX
r; ,.!; ·~~~~""~'";r,~;"0~~~~~:i; · · ~~ ~··i·~~~c.: .. , .·,i~ · I 37'-10" l ,s·-,o~ I
E9BUILDING ELEVATIONS NTS
PROPOSED SKINNER RIDGE CENTRAL COMPRESSION FACILITIES SECTION 36, T5S, R98W, 6TH PM
W 1/4 CORNER SECTION 36, T5S, R98W _.. FOUND STONE W/POST ~ "!:'s
"''"'· ·~::'i.
""
LEGAL DESCRIPTION:
I/ )
I /
A PARCEL OF LAND SITUATE IN TRACTS 103 AND 104 LOCATED IN THE NW 1/4 OF SECTION 36, TOWNSHIP 5 SOUTH, RANGE 98 WEST OF THE 6TH PRINCIPAL MERIDIAN, COUNTY OF GARFIELD, STATE OF COLORADO, THE PERIMETER BEING MORE PARTICULARLY DESCRIBED FOR AREA AS FOLLOWS:
I
COMMENCING AT A FOUND STONE IN PLACE FOR THE W 1/4 CORNER OF SAID SECTION 36, WHENCE A FOUND 1924 GLO BRASS CAP IN PLACE FOR THE NORTHWEST CORNER OF SAID SECTION 36 BEARS N00'04'39"W A DISTANCE OF 264-3.38 FEET, WITH All BEARINGS CONTAINED HEREIN BEING RELATIVE THERETO; THENCE N16'38'57"E A DISTANCE OF 213.19' FEET TO THE TRUE POINT OF BEGINNING OF THE PARCEL DESCRIBED HEREIN: THENCE N68'48'5.3"E A DISTANCE OF 740.3.3 FEET: THENCE S25'11'.30HE A DISTANCE OF 507.55 FEET: THENCE S55'02'.39"W A DISTANCE OF 887.02 FEET; THENCE N14'22'17"W A DISTANCE OF 722.56 TO THE POINT OF BEGINNING, CONTAINING 11.19 ACRES MORE OR LESS.
NOTES: 1) THE PROPOSED SITE AS SHOWN AND DESCRIBED ABOVE IS NOT A BOUNDARY SURVEY AND NO MONUMENTS WERE SET, THE PURPOSE OF THE ABOVE LEGAL DESCRIPTION WAS TO DESCRIBE THE PERIMETER AND AREA WITHIN CHEVRON PROPERTY FOR THE PROPOSED SKINNER RIDGE CENTRAL COMPRESSION FACILITY.
2) THE CENTRAL fACIUTlES EQUIPMENT ARRANGEMENT AS SHOWN ABOVE WAS PREPARED BY URS - WASHINGTON DIVISION PER PLAN PBSR-59836AVf-CIV-LAY-URS-00000-00D05-00, REV 0, DATED APRIL 22, 2008.
1~' 0 ·~·
~-- I GRAPHIC SCALE IN FEET I INCtl ~ 1SO fW
SURVEYOR'S CERTIFICATE I, George R. Bouer: o Professional Lond Surveyor in the Stote of Colorado do hereby certify thot this Survey wos mode under my direct supervision, ond thot this Site Pion represents soid Survey.
COLORADO P.LS. 27925
F'IOIEF'A!OIIiiD 1"0101, Ci-!liiYI::<ON U.S.A INC.
COI\Ii!>TI'I!UCTION i!>UI'I!VS'Ti'>, INC. Oii:'l2 i!>UNI'I!Ii!>E 6L. YD. PBSR-59838AVF-CIV-SRV-CSI-00000-00001-U02
i!>IL. T, CO 61~!02 DRAWN BY: BLM CHECKED BY: GRB PWO:CHEVRON CENTRAL-fACILllES DATE:04 29 08 SCALE: 1" = 150' SHEET: 1 Of' 1
Group W Engineering, Bnc. 871 South Dudley Street lakewood, CO 80226 (303) 969-9774
Structural Calculations GWE Project #0823
For: J.W. Williams, Inc.
Piceance Development Project
MBD-1075 Liquid Separator Skid
)
Company Address
City, State Phone other
Group W Engineering
871 S. Dudley St Lakewood, CO
303-969-9774 groupwengialaol.com
JOB TITLE Chevron MBD-1075 & 1040
JOB NO. 0823 SHEET NO. I CALCULATED SY~E~C:=::_------ DATE --9/2Ji58
CHECKED BY WGR DATE
W\\-W,s1ruware.Col11
STRUCTURAL CALCULATIONS
FOR
Chevron MBD~1075,
)
Company Address
City, State Phone other
Code Search
I. Code: International Building Code 2003
11. Occupancy:
Occupancy Group = Hi. High-Hazard
Ill. Type of Construction:
Fire Rating: Roof= O.Ohr Floor= 0.0 hr
IV. Live Loads: Roof angle (~) 1.14/12 5.4 deg Roof 0 to 200 sf: 20 psf
JOB TITLE ChevronMBD-1075
JOB NO. ~~-----SHEET NO. _:.lA'-'--:c;=c-CALCULATED BY DATE 9/2/08
DATE
www.struware.com
200 to 600 sf: 24 - 0. 02Area, but not less than 12 psf over 600 sf: 12 psf
Floor Stairs & Exitways Balcony I Deck Mechanical Partitions
250 psf 100 psf
NIA
NIA
V. Wind Loads : ASCE 7 - 02
Importance Factor Basic Wind speed Directionality (Kd) Mean RoofHt (h) Parapet ht above grd Exposure Category Enclosure Classif. futernal pressure Building length (L) Least width (B) Kh case 1 Kh case 2
us./ 90mph
0.85 14.0 ft 14.0 ft
c Enclosed Building
+/-0.18 34.5 ft 14.0 ft 0.849 0.849
Topographic Factor (Kztl Topography 2D Escarpment
15. J f\ 25.0 f\
Hill Height (H) Half Hill Length (Lh) Actual H!Lh UseH/Lh ModifiedLh From top of crest: x= Bldg up/down wind?
H!Lh= 0.50 x/Lh = 0.89 z/Lh = 0.50
At Mean Roo fl-It:
0.60 0.50
30.2 f\ 27.0 f\
downwind
Kzt = (l+K1K2K3)'2 =
0.425 0.776 0.289
!.200 20 RIDGE or 30 AXISYMMETRICAL HILL
Company Address
City, State Phone other
Transverse Direction.
Kz=Kh= Base pressure (qh) =
GCpi=
0.85 (case 1) 17.2 psf +1-0: \8
JOB TITLE Chevron MBD-1 075 & 1040
JOB NO. _::0_::82::::3c_ _____ SHEET NO. 2 CALGULA TED BY EC DATE 9/2/08 _ _.:::.:::.:::::_
CHECKED BY WGR DATE
Longitudin~l Direction
Edge Strip (a) End Zone (2a) Zone.2.length =
Torsional loads are 25% of zones l - 4. See code for loading diagram
.·
3.0 ft 6.0 ft 7.0 it
Transverse Direction Longitudinal Direction pcrpendicUlnr 0 .. 5.4 tl~g Parallel e 0.0 deg
Surface GCpf w/-GCpi w/+GCpi GCpf w/~GCpi w/+GCpi
I 0.40 0.58 0.22 0.40 0.58 0.22 2 -0.69 -0.51 -0.87 -0.69 -0.51 -0.87 3 -0.37 -0.19 -0.55 -0.37 -0.19 -0.55 4 -0.29 -0.11 -0.47 -0.29 -0.11 . -0.47 5 - . -0.45 -0.27 -0:63 -0.45 -0.27 -0.63 6 -0.45 -0.27 -0.63 -0.45 -0.27 -0.63· IE 0.62 0.80 0.44 0.61 0.79 0.43 2E -1.07 -0.89 -1.25 -1.07 -0.89 -1.25 3E -0.53 -0.35 -0.71 -0.53 -0.35 -0.71 4E -0.44 -0.26 -0.62 -0.43 -0.25 -0.61
Wind Sur:l'ace pressures (psf)
1 10:1 3.9 10.0 3.8 2 -8.& -15.0 -8.8 -15.0 3 -3.3 -9.5 -3.3 -9.5 4 -2.0 -8.2 -1.9 -8.1 5 -4.7 -10.9 -4.7 -10.9 6 -4.7 -10.9 .:!J-_7 -10.9 -·
IE ( 13J-(,xl~ 7.5 ~)U.)61&1.4 .C..0NS G/ZV<TT• V:~'-)" 2E -15.3 -21.6 -15.3 -21.6 P.t:st G-Jv.Si) 1'011-3E -6rl'\ -12.3 -6.0 -12.2 4E 6v)es -10.6 /-4:~u)o :;' -10.5 lio P<>F VJuJ QuJl)fZ z.c.
'---" 5 p;;p LG~EW1?l-IJ IEP.t7!{1..(?" Sv!'tP4tf e.>.Jlifi<> $V;1nrc.6 /IJ 5oTif P 1 flBI:.(I ot1.15;.
WlNDWJ\11.D
Windward roof overhangs: -11.7 psf (upward) add to windward roof pressure
0\1ER.HANG ffi WH'IDWP.RDROOF
. l 1 l l l l l I LEEWARDRCDF _________ tt !lt! tJ
~~~~ Parapet
Wind\vard parapet: 31.5 psf (GCpn=+1.8) -19.3 psf (GCpn = -1.1) Leeward parapet:
Horizontal MWFRS Simple Diaphragm ·Pressures (psD Transverse direction (normal to L) Interior Zone: Wall 12.0 psf
Roof -5.5 psf End Zone: Wall 18.1 psf
Roof -9.2 psf
Longitudinal directjon (parallel to L) Interior Zone: Wall 11.9 psf
End Zone: Wail 17.9 psf
TR.A..l'TSVE:RSE ELEVATION
ffi VIINOWJ>.RDROOf
t t l l t ! I ,'-'f'f'f't'f) VERTJCi',L
LONGITtTDD.-TALELEVATION
)
Vii. Snow Loads :
Company Address
City, State Phone other
Roof slope Horiz. eave to ridge dist (W) =
Roof length parallel to ridge (L)""'
5.4 deg 7.0 ft
34.5 ft
Hip and gable w/ trussed systems Type of Roof Ground Snow Load Importance 9tegmy Importance Factor Tbennal Factor Exposure Factor
Pg ~ 65.0 psf ]]]
I = 1.1 Ct = 1.10 Ce = 0.9
Pf= 0.7"'Ce*Ct*l*Pg Pfmin
Flat Roof Snow Load Pf =
Rain on Snqw Surcharge Angle Code Maximum Rain Surcharge Rain on Snow Surcharge Unobstructed Slippery
Surface (per Section 7.4) Sloped~roofFactor Cs =
49.5 psf 22.0 psf
49.5 psf 2.38 deg
5.0 psf 0.0 psf
no 1.00
JOB TITLE Chevron IvfBD-1075 & 1040
JOB NO. 0823 cALCt,JlATED.BY EC
CHECKED BY WGR
Terrain A B c D
Above treeline Alaska~no trees
SHEET NO.
DATE DATE
EXposure Factor, ·Ce
3 9/2108_
Exposure of roof Fully Partiallv Sheltered
nfa 1.1 1.3 0.9 1.0 1.2 0.9 1.0 1.1 0.8 0.9 1.0 0.7 0.8 nfa 0.7 0.8 nfa
Design Roof Snow Load {Ps) 49.5 psf ("balanced" snow load) NOTE; Alternate spans of continuous beams and other areas shall be loaded with half the design roof snow load so_as to produce the g~:eatest possible effect~ see code.
Building Official Minimum 49.5 psf
Unbalanced Snow Loads~ for Hip & Gable roofS' only 70/W+O.S
Windward snow Joad = Leeward snow load =
l05deg Unbalanced snow loads are not required 49.Spsf
Leeward Snow Drifts~ from adjacent higher roof Upperrooflength 1u =
Projection height h = Building separation s = Adjacent structure ·factor Snow density Y = Balanced snow height hb =
he~
49.5 psf
O.Oft O.Oft O.Oft l.UO
22.5 pcf 2.21 ft
-2.21 ft hclhb <0.2 ~ -1.0
Drift height
Therefore, no drift
Drift width Surchar~e load:
hd = w=
pd ~ g'hd~
0.00 ft -17.66·ft
OoO psf
Windward Snow Drifts .. Against walls. paraoets. etc more than 15' long-·
Building roof length lu - 0.0 .ft Projection heiJ;ht h = 0.0 ft Snow density "( = 22.5 pcf Balanced-snow height hb = - 2.2.1 ft
hclbb <0.2 ~ -1.0
Drift height Drift width Surcharge load:
he = -2.21 ft Therefore, no drift
hd = w=
pd = g'hd=
6,oo ft -!7.66 ft 0.0 psf
h
)
JoB TITLE Chevron MBD~ 1075 & l 040 Company Address
City, State Phone other
JOB NO, 0823 SHEET NO. ____ _:4::_ CALCULATEDBY~E;';Co:=-------- DATE 9/2/08
----"'= CHECKED BY WGR DATE
VI. Seismic Loads: IBC 2003
Seismic Use GrOup: Importance Factor (I):
Site Class:
Ss (0.2 see)= Sl (!.Osee)=
Fa=
Fv=
1.496
2.400
Il 1.25
D
38.00,%g 9.00 %g.
Seismic Design Category "" C
Number of Stories: Stmcture Type: Not applicable
Plan Structural Irregularities: No plan Irregularity
Vertical Structural Irregularities: No vertic~llrregularity
Flexible Diaphragms: Yes
Sms= Sml =
Building System: Building Frame Systems
0.568
0.216
Sds =
Sd1 =
Seismic resisting system: Ordinary steel concentrically brnceJ} frames
System Building Height Limit: Height not linrlted Actual Building Height (bn) = 14.0 ft
DESIGN COEWJCIEN'J'S AND FACI'ORS
Response Modification Factor (R) = System Over..Strength Facto.r (Qo) =
Deflection Amplification Factor (Cd) = Sds~
Sdl ~
5 2
4.5 0.379 0.144
JBCi003 Simplified Analysis
5 2
4.5
Code Reference Section for Detailing: AISC Seismic Section 14 Seismic Load Eflbct (E)- p Q, +/- 0.2Sp8D
·Special Seismic Load Effect (Em)= Qo Q, +/- 0.2Sos D - p Q, +/= 2.0 Q, +/-
PERMITTED ANALYTICAL PROCEDURES
Index Force Analysis (Seismic Catego>:y A only)
Shnplified Analysis Method Not Permitted
Equivalent Lateral~ Force Analysis Buildin8 period coef. (Cr) =
Approx fundamental period (Ta) ~ User calculated fundamental period (T) =-
Seismic response coef. (Cs).= need· not exceed -Cs =
but not less than Cs = USECs=
• Pennitted 0.020
Crh:=
Sdsl/R =
Sd!l/RT=
0.044Sdsl =
Method Not Penuitted
0.145 sec 0 sec
0.095 0.249
0.021 0.095
x.=0.75
0.379
0.144
Design Category ==
Design Category=·
0.076D 0.076D
p = redundancy coefficient Qs = horizontal seismic force D=deadload
CQ = !.61 Tmax = CuTa = 0.233
UseT= 0.145
Design Base Shear V ~ 0.09SW (..PN'5G'f/,v(fT11)fL.. !.{
Model, Linear & tionlinenr Response Analysis -Permitted (see code for procedure) U:'>GD \) '= 0. / 0'
ALLOWABLE STORY DRli'I'
Stmcture Type: All other strucnues
Allowable story drift= 0.015hsx where hsx is the story height below level x
c c
)
)
Company Address
City, State Phone other
Group \V Engineeri11g, Inc. 87 IS. Dudley St. Lakewood, CO 80226 303-969-9774 groupweng@aol.com
JOB TITLE Chevron MBD-1075 & 1040
JOB NO. 0823 CALCULATEOBY~E~C~-----------
CHECKED BY WGR
CODE SUMI\'LO-RY
Intemarionn! Building Code 2003
Live Loads:
Roof 0 to 200 sf: . 20 psf 200 to 600 sf: 24- 0.02Area, but not Jess than 12 psf
over 600 sf: I 2 psf
Floor Stairs & Exitways Balcony I Deck Mechanical Partitions
Dead Loads:
Floor Roof
Roof Snow Loads:
Design Roof Snow load Flat Roof SnoW Load Snow Exposure Factor Importance Factor Thermal Factor Ground Snow LOad Rain 011 Snow Surcharge Sloped-roof Factor
Wind Design Data:
Basic Wmd speed Mean RoofHt (h) Building Category Importance Factor Exposure Category Enclosure Classif. Internal pressure Coef. Directionality (Kd)
Earthguake Design Data:
Seismic Use- Group : Importance Factor Mapped spectral response
accelerations Site Cinss Spectral Respons~ Coef.
Seism\c Design. Category Basic Structural System
·Seismic Resistihg System-Desig11 Base Shear ~eismic Response Coef. Response ModifiCation Factor
Analysis Procedure
250 psf 100 psf
NIA
NIA
82.4 psf 6.8 psf
Pf = Ce =
I = Ct= pg_ ":
Cs =
90mpb 14.0 ft
IV iJ5
c Enclosed .Building
+/-0,18 0.85
I = Ss =
SI -
Sds = Sd! ~
49.5 psf I 49.5 psf
0.90 1.!0 1.!0
65.0 psf 0.0 psf
!.00
u !.25
38.00 %g 9.00. %g
D 0.379 O.I44
c = Building Frame §ystems = Ordinary steel' concentrically braced frames
V= 0.09SW Cs = 0.095 R= 5
= Equivalent Lateral-Force A11alysis
SHEET N0. ___ =~5
DATE _ _;9'-'i2J:::Ooc8 DATE
www.struware.com
)
)
Company Group W Engineering,. Inc. JOB TITLE Chevron MBD~l075 & 1040 Address 87 lS. Dudley St.
City, Siaie Phone other
Lake,vood, CO 80226 303-969-9774 group\veng@noJ.com
JOB NO. 0823 CALCULATED BY ~Eo;.C;=------
CHECKED BY WGR
CODE SUMlvlARY- continued
Component and cladding wind pressures
Roof
C&C<90 feet
·Area
Negative Zone 1 Negative Zone 2 Negative Zone 3
Positive All Zones
Overhang Zone 1&2 Overhang Zone 3
Wall Area
Negative Zone 4 Negative Zone 5
Positive Zone 4 & 5
Surface Pressure (psf) 10 sf 50 sf 100 sf
-20.3 -19.1 -18.6 -34.1 -25.7 -22.1 -51.4 -30.9 -22.1 10.0 10.0 ]0.0
-29.3 -28.1 -27.6 -48.3 -24.2 -]3.8
Surface Pressure (psf) IOsf JOOsf 500sf
-20.2 -17.4 ;45:5 ') -24.8 -19.3 "·45.5--/ 18.6 15.9 -:j,j])
SHEET NO. --=-:;:';:-5 A DATE 9/'}}08
DATE
www.stroware.com
(
'
)
D2re Checked Chocked By Job Number By
,zr:.._ Project
MBO~ 'Q-:1-?' J., i ~
.. -~. '(' ~,, f':T~; .. ~":· ::.;, ~-c~:1,( n,-t!7~t:i;
' ~ . {.~:114.;:::_~ !, _,. •• , .-::.·
·-"· . . ·,:-.... . ,,.;._,,,
_·; ·-··-. ...,..._, .
.4 .. ·
., ?_
{~_:; ~~ ,-.:~~ -:z 3 3 l <6
\o -r>tL LOAD -r_ ~~Eel.-)
Li Q.UID ·'-.,
-~. 0 ~ ' -r 1-'r r.:· \. . . ~~- . I .
' "\ ' Lb lF-,· ·'
Date Calc. No. Sheer No.
cn/;ii~J? _t--~
Subject
\ SF='P f'r 12 ft'T Of:< ! !0•.) \ \) I.
.
)
)
Dare Checked Ched::ed By JobNumbe.r
Project
.. ;·. ; . _;....,.
i,./) f; 0 J:"
LOA-D A. P-PLte: D t!'--..J f>l\0 DeL-
By Dare
F(
Sub jeer
_,.. I • r_of\D= ~-r x tT 1
(?>s,o_. o!
Calc. No. Sheer No.
To AcwuPT tt-'fL fV\.!SC. P' ?t:='";:}
·,jd-1 ')CC , ..... ,..-' , '-· vJ _. •,::...· .... ~
'1--':"o f'l ( Z'lSFr:Ao.Gt-?;=)(9: Z.b'rr) ( 0/2>5 IC>.~ ~ 5~./1<( rf' '? 3cr.:r11 .0e:6 trBoul5
/ . . · _,.. :. Ok
- (50-I krp ? 4-0:/K. - . _ _ _ ; • oK L-- -( S bF SliCCTforJ G
.t-op ... _ Lt'ET !r·._Jr:7\ P1 Pt r){f'> L..-of::t) /:·S::..•.Jf'./.8 Nr:.) -
! t'\1·1•''' --• \,<;I, ., ' ,_..· I
:::-z4-oS K ) 14- &K :. QJ.<.
L__:__ _________ ...;.._:__ ____ ....L__~----
. ,oads; BLC .l, OL(bldg)
1,~3=-ro::.u::.!p::_:_W:_:·_:E::.n;.;;g~in:.:.e:..:e:.:.ri.:.:n;cg __
EC 0823
MBD- 1075 (Operating)
1 i
~I ~ 'I L
Sept?, 2008 at 12:24 PM
Operating Loads - 1 075.r3d
)
'ads: BLC 2, SL (bldg}
r3roup W. Engineering
EC
0823
MBD ~ 1075 (Operating)
Sept?, 2008 at 12:24 PM
Operating Loads - 1 075.r3d
1ads: BLC_ 3. OL (piping+llquid)
/~ou.cp...:W:.:..:... =En:.:;g~in.:ce...:e...:ri...:ng"--j EC 0823
MBD- 1075 (Operating)
3 <;(J l-?si" p tfli/V b., (._gk-r:)
Sept 7, 2008 at 12:25 PM Operating Loads • 1 075.r3d
l
.oads: BLC 4, LL(DeckUve)
,.3roup W. Engineering
EC
0823
MBD • 1075 (Operating)
Sept 7, 2008 at 12:25 PM
Operating Loads. t075.r3d
y
,Asi, ! X
)
i
)
Loads: BLC 5, SelfWeight
; Group W. Engineering.
EC
0823
MBD- 1075 (Operating)
Sept 7, 2008 at 12:25 PM
Operating Loads - 1 075.r3d
)
I
)
i ·I
L--·~' ;:--:,.,.----~--=--------i;;:--------..l,\
.pads; BLC 6, Wind(Transv.)
13roup W. Engineering
EC
0823
MBD- 1075 (Operating)
Sept 7, 2008 at 12:26 PM
Operating Loads • 1 075.r3d
A:, )()Sl. I
I z X I
)
I
/ . oads: BLC 7. Wmd(Lon !j1.)
1 lroup W. Engineering
EC 0823
MBD- 1075 (Operating}
Sept?, 2008 at 12:27PM
Operating Loads -1075.r3d
i '
I y I 4il· Z X
)
loads: BLC 8, Seismic(Transv .) So!ullon: Envelope
/3roup W. Engineering
EC
9823
MBD - 1075 (Operating)
Sept 7, 2008 at 1:02 PM
Operating Loads - 1 075.r3d
)
I
)
1 .oads: BLC 9, Seism!c(Longit.) olu!ion: Envelope
3roup W. Engineering
EC 0823
MBD - 1075 (Operating)
~--At• D.' L. ~~) V-/ 561SN\\C..
~-::on_.c..e; e:;:;;
Sept 7, 2008 at 1 :02 PM Operating Loads • 1 075.r3d
r-----v ~~ ------~------~-~
~xi z
)
)
:Oiullon: En~telope
13roup w. Engineering MBD- 1075 (Operating)
EC 0823
!. I/
/I I !
I
Sept 7, 2008 at 12:29 PM
0 eratlng Loads-1075.r3d p .
)
)
Solulion: Envelope
J3roup W. Engineering
EC 0823
MBD • 1075 (Operating)
Sept 7, 2008 at 12:30 PM
Operating Loads • 1 075.r3d
I Ail I z X I
}
Solullon: Envelope
Group W. Engineering
EC
0823
.... ,:- rJk, •• ¥- ··-:::>·· ,I "-. -···
MBD - 1075 (Operating)
Sept 7, 2008 at 12:30 PM
Operating Loads -1075.r3d
Company Group W. Engineering Designer EC Job Number 0823
) Basic Load Cases
MBD - 1075 (Operating)
Sept 7, 2008 1 :03 PM Checked By:
Rl r, I X (.;re .. V r,., Z Grav . Joint Point nlohih . I .
1 m blda nl 14 ···2''. . ' • .. o;C: ... bide' . . : >'•··•./eo :'< '····'' . ~~ ·. · · <in/ P:'"'·'' ,.
.~· . .~~'i;4;d\ : .. · , .... . · .. · .
. i
···~" ,, ••. t···' '·. ·' ·• : . ··s '·''· ,.:' · ... · . . ··· .. ·, . ::.'':.>:;;·• ·r:·2:r J. ''':':'
2
~····· .. , .. 80
Load Combinations
Company Designer . Job Number :
Group W. Engineering EC 0823 MBD · 1075 (Operating)
Sept 7M2oos 1:03 p Checked By:
Company Designer Job Number
Group W. Engineering EC 0823 MBD - 1075 (Operating)
RISA-3D Version 7.1.1 [C:\Persona~Bill Rose\Chevron 1 075\0perating Loads - 1 075.r3d]
Sept 7, 2008 1:03PM Checked By:
Page29
Company Designer Job Number
Group W. Engineering EC. 0823 MBD - 1075 (Operating)
) Envelooe AISC ASD Steel Code Checks (Continued)
Sept 7, 2008 1:03PM Checked By:
Page 30
Company Designer Job Number
Group W. Engineering EC 0823 MBD - i 075 (Operating)
Sept 7t ?008 i :03 PIVJ Checked By:
Page 31
)
Company Designer Job Number
Group W. Engineering EC 0823 MBD - 1075 (Operating)
RISA-3DVersion 7.1.1 [C:\Personai\Bill Rose\Chevron 1 075\0perating Loads - 1 075.r3d]
Sept 7, 2008 1:03PM Checked By:
Page 32
Company Designer Job !'lumber
Group W. Engineering EC 0823 MBD - 1075 (Operating)
) Joint Coordinates and Temperatures (Continued) Label l<rftl v fft 7 rft:
81 21.17 1::! R 14 i'Ulitll"'::,•:,:. -.,.:,,;: ··· '.'·{';c_··'···. f":J:C•.'·<:.''28)'• ' ·, · . .' f'.<,:·c;,···''·l4 ·' ·· ·
)'
.~
n
Sept?, 2008 1:03PM Checked By:
. (]' .•. '{'1 .•. ·· . •i'(if'·'· .
·.·.·.·:;-c
RISA-30 Version 7.1.1 [C:\Personai\Bill Rose\Chevron 1075\0perating Loads- 1075.r3d] Page 33
/
oads: BLC 1, DL(b!dg)
1roup W. Engineering
1:C
0823
P~t~Ji:3L D L-,.
M BD - 1 075 (Lifting)
Sept 7, 2008 at 1:41 PM L'1ft'mg Loads -1075.(.Jd
I
·'
zofSF MISC·
-PtP' /\) &. /){,
.oads: BLC 3, DL {pJplng)
>roup W. Engineering
'Ec
0823
MBD - 1 075 (Ufting)
Sept 7, 2008 at 1:42PM
Lifting Loads • 1 075.r3d
rv
z ~X
l
Loads: BLC 5, SelfWe!ght / Results for LC 1, DL x 2
0823
(-l'f:C( l
bJ?I'\) t "T'"'y
MBD - 1 07& (Lifting)
Sept 7, 2008 at 1:47 PM
Lining loads -1075.r:ld
y
b. ~
Z X
)
J
.oads: LC 1, 0Lx2
3roup W. Engineering
EC
0823
MBD - 1075 (Lifting)
Sept 7, 2008 at 1:42 PM Lifting loads • 1 075.r3d
)
J
lesults lor LC 1, Dl x2 ~eaction unils are k and k·ft
~roup W. Engineering
EC
0823
26.1
MBD- 1075 (Lifting)
Sept 7, 2008 at 1:43 PM
lifiing Loads· 1075.r3d
Company Designer Job Number
Group W. Engineering EC 0823
) Basic Load Cases
MBD- 1075 (Lifting)
Sept 7, 2008 1:43PM Checked By:
BLC _X G.ra. V Gre 7 G>ev Joint Point Distdh. A>oe. (. Surtoc. 1 )L ria\. DL 2 Ia'· SL I •
3 iil) JL .. 4 . . · ·-.·_ U.~·· · · ' · _:: .
5 Self' JL
Load Combinations
. 14 . ,-. 10 . .
'/: i .. : ..
•
-:R-);; ,,_-.,·,,.--;(.::•: .• ,-.
.-•· , ..
147 I
I 1 I lves I 1 [ I _ Ji I 2 [ I I I I [ I I
RISA-3D Version 7.1.1 [C:\Personai\Bill Rose\Chevron 1 075\Lifting Loads - 1 075.r3d] Page 1
)
.-·
Company Designer Job Number
Group W. Engineering EC 0823 MBD - 1075 (Lifting)
RISA-30 Version 7.1.1 [C:\Personal\Bill Rose\Chevron i 075\llfting Loads - 1 075.r3d]
Sept 7, 2008 1:43PM Checked By:
Page 2
Company Designer Job Number
Group W. Engineering EC 082"3 MBD - i 075 (Lifting)
RISA-30 Version 7.1.1 [C:\Personai\Bill Rose\Chevron 1 075\Liftlng Loads - 1 075.r3d]
Sept 7, 2008 i:43 PM Checked By:
Page.3
Company Designer Job Number
Group W. Engineering EC 0823 MBD- 1075 (Lifting)
. Member AJSC ASD Steel Code Checks (Continued) ) LC Member Shane UCMax Loclftl Shear U ... Lnr.fftl Dir Fafksil
1i4' ··M:fi4' Tii!f'l:'''s:ox.:. .434 ·.• .. b ..
. 3ii6i 'Y5' ?1<47'4 "1' 115 1 M115 IPIPI:' s.ox ... .642 0 .339 1 21.429
ifi:6 .{ Mll6~1PIPE 8.0)( .. ,533 0 ·.·. :375 ':15 -21:474
Hot Rolled Steel Prooerties
Flfksil Fhvfk<il Fbzrkon 21.6 ·. 23'ifi' 23>76 21.6 23.7R 23.76 21 6' 23.'7R, <23:76
RISA·3D Version 7.1. i [C:\Personal\8111 Rose\Chevrori 1075\Liftlng Loads· 1075.r3d]
Sept 7, 2008 1:43PM Checked By:
Cb Cmv Cmz 1.75 .6 :a·5. 1.75 .6 .85 1:•75 .6 .· .. :85
Fnn
I'J2C.:'f H2-1
fRjc?
Page 4
Company : Designer : Job Number:
Group W. Engineering EC 0823 MBD - 1075 (Lifting)
RISA-3D Version 7.1.1. [C:\Personal\Bill Rose\Chevron 1 075\Lifting Loads - 1 075.r3d]
Sept 7, 2008 1:43PM Checked By:
Page 5
" I
Company Designer Job Number
Group W. Engineering EC 0823 MBD- 1075 (Lifting)
Joint Coordinates and Temperatures (Continued)
Sept 7, 2008 1:43PM Checked By:
) 1 ohol X lftl Y lftl Z lftl Temn IFl Detach From Diao.
)
93 ,~;94< I 95
N91A 3.5 6.75 14 0
N9s 2s o +---''-"-'""'_ .'=7s::--'--"'--+-c:__~o~:..___:_+-----l
RISA-30 Version 7.1.1 [C:\Personai\Bill Rose\Chevron 1 075\Lifting Loads - 1 075.r3d] Page 6
Date Checked
C A-/'f"'~ /\ LLIJ'. __ ":" ~- 1(.".
Chocked By
Projecr
i f
Job Number By Date
Subjecr
Cllfllc.rF'1 dF we'-D/!Vl _ ¢~=-v.tr{o.&Yro)(-!#J(I·o)
- 5' 5( /L-j~lf)
' -i-o!.ttrr_. (_t;(Jnr~-!'t"tf ;:)::-..: · .... u::?,-~:; ~" .. ·:,f ~<~4{\<',·(~·t·).·
)[-Ci .. VL;J/t0L6'- C/...JC'LD {1';'f!f( 1/Y ~·· 1];/1·( "\. (,(:?
~ri-(
Calc. No. Sheet No.
.~
)
' /
·,- .
Sent: Subject:
Wednesd;y, September 03, 2008 6:08-PM Fwd: Vessel Weights
From: GFoster@jwYJilliams"ftint.com To: GROUPWENG@aol.com Sent: 9/3/2008 3:24:32 P.M. Mountain Daylight Time Subj: Vessel Weights
Bill,
These are calculated weights with no adjustments taken.
Gas Separator
MBD-1040
. Empty Weight 17,400 lbs .
Test Weight 33,000 lbs.
Liquid. Separator
MBD-1075
Empty Weight 14,600 lbs.
Test Weight · 46,100 lbs;
George Foster
Engineering & Estimating Manager
J. W. Williams Inc.
(936) 931-2424
9/3/2008
.-.
)
.J
I
T(;,.JO
~~c~ -. t,J ·_,1 I 'Q.ib . ' .
:;: . _., ·.~·· i
lwo
;·-. :_.)
f'. IS i n • i.> ') ""' •:. '.:. v r~~ .:.,J '·· , ....... ~
.. -· Loa'ds: BLC 3, DL (piping+liquld) >olu1ion: Envelope
'3roup W. Engineering
f:c 0823
MBD- 1075 (Operating)
>"' (,;::;!\ !~ C.t'!fl't·.JC.., 6!) /'~ .. A c ~, ..... , e / rn.o{V\ -~' 1.) (C:. ' I;; \,~.(~
[rOA·f:;, TO A I,J!6 (..0/trf::. .
Sept 7, 2008 al1 :27 PM
Operating Loads- 1075 With Line ...
.-
Company Designer Job Number
Group W. Engineering EC 0823
) Basic Load Cases BLC
Load Combination$
)
MBD- 1075 (Operating)
Sept 7M2008 1:27 P I Checked By:
' '
)
)
Company : Designer : Job Number:
Group W. Engineering EC 0823 MBD - 1075 (Operating)
Sept 7, 2008 1:27PM Checked By:
RISA-3D Version 7.1.1 [C:\ ... \Bill Rose\Chevron 1 075\0perating Loads- 1075 With Line Loads.r3d] Page 2
)
Company Designer Job Number
Group W. Engineering EC 0823 MBD • 1075 (Operating)
Sept 7M2oos 1:27 p Checked By:
RISA-30 Version 7.1.1. [C:\ ... \8111 Rose\Chevron 1 075\0peratlng Loads • 1075 With Line Loads.r3d] Page 3
Company Designer Job Number
Group W. Engineering EC 0823 MBD - i 075 (Operating)
Sept 7t ?OOS i:27 PIVI Checked By:
RISA-30 Version 7.1.1: [C:\ ... \Bill Rose\Chevron 1075\0perating Loads- 1075 With Line Loads,r3d] Page4
)
Company Designer Job I'Jumber
Group W. Engineering EC 0823 MBD - 1075 (Operating)
Sept 7, 2008 1:27PM Checked By:
r '
Conwany Designer . Job 1\Jumber:
GroupW. Engineering EC 0823 MBD- 1075 (Operating)
Joint Coordinates and Temperatures (Continued)
Sept 7, 2008 1:27PM Checked By:
RISA-30 Version 7.1.1 {C:\ ..• \Bill Rose\Chevron 1 075\0perating Loads - 1075 With Line Loads.r3d] Page6
)
Company Designer Job Number
Group W. Engineering EC 0823 MBD . 1075 (Operating)
Sept 7M2008 1:27 p Checked By:
RISA-3D Version 7.f1 [C:\. .. \Bill Rose\Chevron 1075\0peratlng Loads- 1075 With Line Loads.r3d] Page?
0
A
Rev
Chevron
CHEVRON PICEANCE BASIN
INCORPORATED
Clerical Revision - IFC 7-Dec-08 TKG Issued for Construction 19-Nov-08 TKG
Issued for Review 04-Nov-08 TKG
Status Date Origin. QA/QC LDE
Document Title:
PICEANCE FIRE PROTECTION PHILOSOPHY PAl Project No. Document No. Page
2033 2033-201-00-ST -0001
RLV TKG RLV TKG RLV TKG
EM PM
1 of14
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033·201·00-ST-0001 Date: 7 December 2008
TABLE OF CONTENTS
REV: 1 ,, Page 2 of 14
1.0 EXECUTIVE SUMMARY ............................................................................................................ 3
2.0 PURPOSE ....................................................................................................................................... 4
3.0 SCOPE ............................................................................................................................................ 4
4.0 CONCLUSIONS ............................................................................................................................. 4
5.0 RECOMMENDATIONS ............................................................................................................... 4
6.0 REFERENCE DOCUMENTS ...................................................................................................... 4
7.0 FACILITY DESIGN PARAMETERS ......................................................................................... 5
8.0 FLAMMABLE HYDROCARBON INVENTORY ..................................................................... 5
9.0 FACILITY AND ENCLOSURE DESIGN PARAMETERS ...................................................... 7
10.0 CONSTRUCTION ......................................................................................................................... 7
11.0 FIRE AND GAS DETECTION .................................................................................................... 9
12.0 FIRE SUPPRESSION .................................................................................................................... 9
13.0 CODE DISCUSSION ................................................................................................................... lO
Tables Table 1: Liquid Inventories .......................................................................................................................... 6
Appendix Appendix A ................................................................................................................................................. 13 Appendix B ................................................................................................................................................. 14
Page 2/14
1.0 EXECUTIVE SUMMARY
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec Nu: 2033R201ROO-ST-0001 Date: 7 December 2008
REV: 1 Page 3 of 14 II
The Chevron Mid-Continent & Alaska Business Unit (Chevron) is currently developing facilities in the Piceance Basin of Western Colorado for the purposes of natural gas production, treatment, transmission, and delivery to sales pipelines. These facilities include modular facilities close to the gas wellheads, as well as a number of modular unit process facilities at a Central Production Facility (CPF) to be located north of the town of De Beque, Colorado.
Because of the unique nature of fire and explosion hazards at natural gas facilities, Chevron has planned and designed these facilities to incorporate fire prevention and protection systems and procedures in accordance with industry standards, relevant building and fire protection codes, and Chevron's Safety in Design program. The purpose of this document is to present the design and operational philosophy Chevron proposes for the development of these facilities within the CPF. The key design parameter in the design of the fire protection system for the CPF is the ability to quickly and automatically depressure most of the facility, shut down the flow of hydrocarbons to the facility, and remove all electrical power, except essential power, upon automatic detection of a fire anywhere in the facility.
As is typical in the petroleum industry, Chevron has designed the production and treatment facilities at the CPF as a series of modular unit processes. Each module is designed to accomplish some function or functions related to natural gas processing, such as removal of water and solids flowing within the gas stream, removal of heavier hydrocarbons from the gas stream, compression of the gas prior to release to a pipeline, metering the gas prior to delivery of the gas to a customer's pipeline, etc. Because of the harsh weather conditions at the site, many of these unit processes are enclosed to protect certain equipment and instrumentation from the elements. Some of the process skids will be mostly enclosed; other process modules will have an enclosure around the instrumentation and control equipment only. Most of the process enclosures will be factory built, and Chevron has been working with the Colorado Division of Housing to secure plan reviews and permits for these prefabricated facilities. Several of the facilities will be sitebuilt enclosures, including a large facility housing the main compression equipment at the CPF. Additionally, some of the prefabricated facilities will house support and utility processes, but will not house any significant hydrocarbon materials.
Because of the nature of the fire hazard associated with the enclosures housing process gases and associated equipment, the primary focus of this narrative will be on the process buildings. The process equipment enclosures are classified by the International Building Code (IBC) as buildings with an Occupancy Classification of H-2. This rating is based on the amount of flammable gas and liquids carried in the equipment and piping within the enclosures. Although buildings with an H-2 occupancy rating are nonnally required to have an automatic sprinkler system, Chevron is proposing to protect these facilities with a non-water-based emergency system in accordance with the exemptions allowed in IBC Section 903.3.1.1.1.
The design and construction of the process building enclosures have been conducted after identifying and taking into account the hazards associated with the types of equipment and materials contained within the enclosure. The design and construction standards utilized are more stringent than required by current industry codes and standards. The enclosures are constructed of noncombustible materials and have fire and gas detection systems specifically designed for the gas processing industry. The egress requirements of!BC Chapter 10 and the NFPA Life Safety Code requirements are also incorporated into the design.
Page 3/14
2.0 PURPOSE
Chevron
~ lliijjil
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Projed Spec No: 2033-20i-OO-ST-000i Date: 7 December 2008
REV; 1 Page 4 of14 II
This philosophy identifies the design parameters utilized to engineer equipment enclosures that meet the requirements of the IBC for buildings with an H-2 rating but without an automatic sprinkler system. This document also establishes that the level of life safety proposed for the process facilities is equivalent to those code requirements.
3.0 SCOPE
This document only analyzes those equipment enclosures located at the Central Processing Facility in Chevron's Piceance Basin Development. It focuses on those enclosures with an H-2 rating by identifying the hazards within the enclosure and the design measures used to mitigate those hazards to personnel who may be present at the time of an incident.
4.0 CONCLUSIONS
The parameters utilized in the design and construction of the equipment enclosures covered by this philosophy adequately protect personnel from the hazards due to the presence of hydrocarbons in the enclosure, without employing automatic sprinkler systems.
5.0 RECOMMENDATIONS
All enclosures covered by this philosophy must be built and installed as designed. Additionally, operational and maintenance procedures should be implemented to ensure that all safety systems are tested and maintained in accordance with IBC and International Fire Code (IFC) requirements.
6.0 REFERENCE DOCUMENTS Reference Document
IBC 2003
IFC 2003
IMC2003
APIRP!4C
APIRPI4G
Document Title
International Code Council -
International Building Code - 2003
International Fire Code - 2003
International Mechanical Code - 2003
American Petroleum Institute -
Recommended Practice for Analysis, Design, Installation, and Testing of Basic Surface Safety Systems for Offshore Production Platforms
Recommended Practice for Fire Prevention and Control on Open Type Offshore Production Platfonns
Page4/14
APIRP500
APIRP752
APIRP 2030
Chevron
~ ...
API Publication 251 OA
COGCC
30 CFR Chapter II
NFPA 101
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Cbevrou Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 Page 5 of 14 II
Recommended Practice for Classification of Locations for Electrical Installations at Petroleum Facilities Classified as Class I, Division 1 and Division 2
Management of Hazards Associated with Location of Process Plant Buildings
Application of Fixed Water Spray for Fire Protection in the Petroleum and Petrochemical Industries
Fire Protection Considerations for the Design and Operation of Liquid Petroleum Gas (LPG) Storage Facilities
Colorado Oil and Gas Conservation Commission-
Rules for Oil and Gas Development in Colorado - Section 606A "Fire Prevention and Protection"
Code of Federal Regulations-
Title 30 (Mineral Resources) - Chapter II Part 250.800 "Production Safety Systems"
National Fire Protection Association-
Life Safety Code
7.0 FACILITY DESIGN PARAMETERS
The CPF is designed to be an unmanned facility. The control system is specifically designed to ensure that in the case of a significant event all instrumentation fails safe, the main electrical feed to the affected area is shut off, incoming hydrocarbon flow to the facility is blocked at the battery limit (boundary) of the facility, and the bulk of the hydrocarbon inventory in the facility is depressured to the facility's flare system. Although some limited portion of the piping and some vessels within the plant may have a residual gas pressure after the shutdown, virtually all fuel sources within the facility will be immediately shut off.
The CPF does not have water available for fire suppression activities. Additionally, no local fire water system exists to provide for tie-in for CPF fire suppression systems.
8.0 FLAMMABLE HYDROCARBON INVENTORY
8.1 Liquid Inventory
The primary fire hazard within the enclosures listed in Table 1 is related to hydrocarbons processed within the facility. In addition to various volumes of natural gas, these buildings will contain various quantities of hydrocarbon condensates (condensates are flarmnable hydrocarbon liquids that condense out of the gas stream when the gas is exposed to typical ambient temperature and pressure).
The hydrocarbon condensate liquid contained in most of the process buildings in Table I is a Class !A flammable liquid (its flash point is less than 73°F and its boiling point is less than I 00°F). The exempt quantity of Class !A liquids, per the IBC, is 30 gallons. The exempt quantity for flammable gases in the IBC is I 000 standard cubic feet, which is
PageS/14
Chevron
~ iiiiiiifiii
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 Page 6 of 14 II
exceeded in each of the building enclosures. Due to the inventory of fla.nunable materials located in each enclosure, a rating of H-2 for each of the enclosures and compressor building is warranted. Fire protection methods based on this occupancy classification are further discussed below.
Gas Separator 604 Condensate -16 37 128 Water
Liquid 426 Condensate -2 78 Separator 1013 Water
Gas Filter Condensate N/A N/A Separator 34 Water
Sales Gas 253 Condensate -20 34 Compressors 42 Water
1000 Lubricating oil 262 >300
Condensate 55 Condensate -2 78 Loading Water
Produced 20 Condensate -2 78 Water and 51 Water Condensate Pumps
Flare Scmbber 257 Condensate -2 78
Water
Vapor 14 Condensate -4 75 Recovery Unit Water
Fuel Gas 35 Condensate -15 37 Water
Page6/14
Chevron .,~
~ ... Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 REV: 1 Date: 7 December 2008 . Page 7 of14
9.0 FACILITY AND ENCLOSURE DESIGN PARAMETERS
9.1 General
Almost all of the process building enclosures will contain some amount of hydrocarbon condensate liquid, which is produced from the wellhead along with the lighter natural gas components. Some of the individual unit processes are specifically designed to remove these flammable liquids and transfer them to holding tanks elsewhere within the plant. The volumes of flammable liquids in many of these enclosures exceed the IBC thresholds at which a building is classified as H-2. These volumes may increase the fire hazard within each enclosure to some degree, but do not change the overall philosophy of our proposed fire protection program.
9.2 All flammable liquids and gases within the enclosures are totally contained within the process piping and ASME-rated pressure vessels. An automatic fire and gas detection system is provided to detect any leaks or fires.
9.3 In the event of a fire anywhere within the CPF, the facility is depressured to the flare to remove the bulk of the flammable gas sources from the fire. Any remaining hydrocarbon liquid would initially be protected and contained within the process piping and/or vessel(s) in which it resides within the enclosure. The rate at which the hydrocarbon liquid would contribute to the ongoing fire would depend upon the amount of dsmage in the containing piping/vessel(s). If the containment is damaged or breached, the materials would burn in place along with the remaining gaseous components. The relative volumes of gas and liquids being burned, and access to the fire of an oxidizing airflow, would determine the extent to which the liquid boils in place as it contributes to the fire.
9.4 Although a combination liquid-and-gas fire might burn hotter and longer than a pure gas fire, the fundamental principle behind our proposed fire protection system is unchanged. The system is designed to contain the fire and allow it to burn out in place. There is no need to attempt to suppress the fire with a water-based sprinkler system. It would likely cause a more substantial hazard by allowing the remaining flammable gases to form a combustible cloud capable of re-ignition until allowed to dissipate.
9.5 It would also be undesirable for the fire department to attempt to put out the fire within an enclosure prior to the consumption of the fuel exposed to the fire. As mentioned above, the remaining gaseous components, along with liquid components that are vaporized due to the heat of the fire, would be dangerous and subject to re-ignition. (See sections 13.3.4 and 13.3.5 for details of this hazard.)
9.6 A closed drain system is provided that removes all liquid from the enclosure's coaming area to a remote underground sump tank. The drain system incorporates P-traps to prevent flammable gases from venting into the enclosure. Liquids collected in the underground sump are subsequently pumped into the facility's above-ground storage tanks.
10.0 CONSTRUCTION
Each enclosure has the following construction attributes:
10.1 All hazardous gases and liquids within each enclosure are housed in self-contained process piping and/or pressure-rated vessels. Piping is designed and constructed in
Page 7/14
Chevron Title: PICEANCE FIRE PROTECTION PHILOSOPHY
~ ~~ iiliiifiii
Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 Page 8 of 14
accordance with ANSI B3 1.3 requirements for gas facilities of this type. All pressure vessels are designed in accordance with applicable ASME Section VIII requirements for these vessels.
10.2 Process piping and vessels are designed to contain all materials with no significant leakage. A fire and gas detection system is specifically designed for each enclosure to detect the presence of hydrocarbons in the air or a fire event, and will initiate emergency shutdown systems within the plant upon detection of a significant amount of hydrocarbons. (Details of this system are described in the following sections.)
10.3 Each enclosure is constructed entirely of noncombustible materials.
10.4 Additionally, all equipment, piping, instrumentation, junction boxes, panel boards and cable within the enclosure are also noncombustible or flame-retardant.
10.5 Adequate access/egress is provided to allow safe evacuation from the enclosure in the event of a fire or gas release in compliance with IBC and NFPA Life Safety Code requirements. These criteria include the provision of at least two means of egress from any building with travel distance to an exit greater than 25 feet. No dead-end corridors are allowed in any of the buildings greater than 20feet.
10.6 Ventilation is provided to the enclosure in compliance with IMC requirements.
10.7 Panic door hardware and emergency exit lighting are provided in compliance with IBC.
10.8 To prevent electrical ignition of hydrocarbon vapors, all electrical components on the process skids are explosion-proof and rated for service in Class I, Group D, Division 1 atmospheres as rated by API RP 500, and each component is certified as such by a Nationally Recognized Testing Laboratory (NRTL). All 208V AC and 120VAC wiring and equipment within each process skid are wired to an on-skid explosion-proof panelboard. All equipment in the compressor building is rated for Class I, Division 2. (The distinction is a result of the presence of the combustion engines driving the compressors.)
10.9 Although the enclosures are designed to be safe when continuously occupied, the facilities in practice will be normally unoccupied. Personnel only occupy an enclosure when conducting equipment monitoring and observance activities; doors are kept open when the enclosure is occupied.
10.10 The operational activities typically require personnel in the enclosure for less than 15 minutes on any given day. Any maintenance activities within the facility will be conducted under stringent safety protocols, including additional fire suppression equipment and personnel being present and the use oflock-out/tag-out procedures.
10.11 Operational procedures at the plant prohibit the accumulation of any combustible materials within the enclosure.
10.12 The design of the site smTounding each enclosure incorporates a barrier zone approximately 20 feet wide covered with noncombustible gravel and no vegetation. Additionally, the site has significant security measures in place, and no admittance to the general public is allowed.
10.13 All enclosures and the process control and safety systems that interface with them were designed using Chevron's "Offshore Gulf of Mexico" standards and design criteria.
Page 8/14
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 Page 9 of 14
Chevron considers these standards to be more stringent than most onshore standards, leading to a more conservative design.
11.0 FIRE AND GAS DETECTION
Each enclosure is equipped with the following fire and gas detection technology, in strict compliance with the IFC and API RP 500:
11.1 Infrared point gas detectors which are tied to a central monitoring system will initiate shutdown of electrical service and hydrocarbon flow to and from the enclosure when gas is detected. These detectors are set to alarm when flammable gas at a concentration of 20% of the lower explosive limit (LEL) is detected. A complete shutdown of power and hydrocarbon flow to the enclosure is initiated when flammable gas at 40% of LEL is detected. All detection and monitoring equipment used at the site is listed by a Nationally Recognized Testing Laboratory (NRTL). See Appendix B.
11.2 A pneumatic fusible loop system consisting of stainless steel tubing pressurized with 40 psig instrument air, and including elements which will melt at 180°F, is provided on all hydrocarbon processing equipment per API RP 500. This system is equipped with a pressure sensor that is tied to a central monitoring system. A loss of pressure in the loop will indicate the affected enclosure and will shut down hydrocarbon flow to and from the enclosure and throughout the CPF and will initiate depressurization of the affected facilities to a dedicated flare. See Appendix A.
11.3 "Triple-infrared" fire detectors will be installed in each enclosure, and when a fire is detected, a programmable logic controller (PLC) will shut down the flow of hydrocarbons to and from the enclosure, as well as throughout the CPF. The bulk of the hydrocarbon inventories throughout the CPF will be depressured to a dedicated flare. (Some minor residual amounts of gas under pressure will still be present in some vessels and piping sections outside of the building enclosures.) Triple-infrared optical flame detectors (known as 'fire eyes' in the gas processing industry) will be installed in all H-2 occupancy buildings and will be tied to the fire alarm systems described above.
11.4 The triple-infrared open-path fire detector system is independent from and redundant with the pneumatic fusible loop system. Both of these systems are independent from the gas detection system.
11.5 Note that the types of detectors described above in Sections 11.1 through 11.3 are provided in lieu of the smoke detector system outlined in IBC Section 903.3.1.1.1. The primary reason for this is that there are no commercially available weatherproof smoke detectors that are rated for Class I, Division 1 service.
12.0 FIRE SUPPRESSION
For these process enclosures, the flammable content hazard located within these enclosures is primarily pressurized natural gas. The experience within the petrolemn industry is that a typical water-based sprinkler system cannot extinguish a pressurized gas fire, and in fact can create more of a hazard than it mitigates.
The standard of the natural gas industry, as codified in API RP 500, is that suppression of a pressurized natural gas fire is best accomplished by immediately shutting off all incoming sources
Page9/14
I rfjS ;:;r~Ni(z_!};r;s Title: PICEANCE FIRE PROTECTION PHILOSOPHY
Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 II Page 10 of 14
of fuel and venting all other inventories of fuel to a flare system. The remaining non-pressurized gas, along with any associated hydrocarbon liquid, is allowed to burn itself out.
For manual suppression of small fires on a limited basis, each enclosure is equipped with handheld 30-lb Class ABC fire extinguishers located at each door.
13.0 CODE DISCUSSION
13.1 IBC
!3.1.1 IBC 2003 normally requires an automatic fire sprinkler system for all H-2 occupancies.
13.1.2 All of the process buildings in this project are classified as H-2 due to the large volume of hazardous materials.
!3.1.3 However, these buildings qualifY as exempt from this requirement per IBC 903.3.1.1.1 Exempt Locations. Comments applicable to the facility under discussion are listed parenthetically following the code citation.
IBC 903.3.1.1.1. Exempt Locations ..... Automatic sprinklers shall not be required in the following rooms or areas where such rooms or areas are protected with an approved automatic fire detection system in accordance with Section 907.2 that will respond to visible or invisible particles of combustion. (In these facilities, an API-compliant gas detection system is installed and designed to respond to concentrations of flammable gas before any combustion takes place.)
Sprinklers shall not be omitted from any room merely because it is damp, of fireresistance-rated construction or contains electrical equipment
I. Any room where the application of water, or flame and water, constitutes a serious life or fire hazard.
(This is true for these facilities. Water sprayed on a pressurized gas fire is unlikely to stop the fire, and could add an explosive hazard due to an unburned gas cloud if it did put out the fire momentarily.)
2. Any room or space where sprinklers are considered undesirable because of the nature of the contents, when approved by the building official.
(This is true for these facilities. Because of the nature of the contents -pressurized natural gas - the petroleum industry standard for safety is to mitigate the risk with an API-RP500 compliant gas detection & emergency shutdown system.)
3. Generator or transformer room ... Not Applicable
4. In rooms or areas that are of noncombustible construction with wholly noncombustible contents.
Page 10/14
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
REV: 1 Page 11 of 14
(This exemption is partially true of the operating buildings in discussion. The buildings are of noncombustible construction, although the hydrocarbon contents within the process piping and vessels are combustible. However, upon detection of fire, the process equipment is depressured and all flammable gases are vented to the flare except for trace amounts remaining in the pipes at atmospheric pressure.)
13 .1.4 IBC Discussion
13.2 IMC
In summary, it is believed the buildings proposed for the Chevron CPF are exactly the type of facility envisioned by tbe code writers when developing this exemption. There is no question that these facilities contain hazardous flammable materials, but application of a water-based sprinkler system would be counterproductive, and would create more safety hazards than it would solve. A far more desirable solution is the substitution of a fire and gas-hazard detection and emergency shutdown system specifically developed for this industry by the API. With the concurrence of the Building Official and Fire Marshall of Garfield County regarding this exemption, the proposed facilities will be in total compliance with the intent and with tbe specific language incorporated into the IBC, IFC and related International codes.
Each of the process equipment enclosures includes either fixed or manually operable louvers which make the use of non-water (gaseous, dry chemical, carbon dioxide, foam, etc.) fire suppression systems problematic. Louvers are provided in compliance witb the IMC, which mandates adequate ventilation for rooms containing hazardous materials. Additionally, standard practice in the gas processing industry is to provide such ventilation to allow flammable gases to disperse, ideally before hazardous accumulations of the gases accumulate within the building. The reasoning within our industry, as codified in API documents, is that ventilating the gas is much safer than trying to contain it within the building.
13.3 API
The Chevron CPF is designed in its entirety to be in total compliance with applicable standards of the American Petroleum Institute.
13.3.1 API RP 500, as detailed above, provides the design standards and details for a gas detection system specifically designed to prevent the accumulation of hazardous levels of flammable and explosive gases as applicable to our industry.
13.3.2 API RP l4G Section 5.7.d "Automatic Fire Control Systems - Enclosed Machinery Areas" indicates "Gas compressors, hydrocarbon pumps, and generators in adequately ventilated enclosed areas are normally not protected by automatic fire control systems."
13.3.3 API RP14G Section 5.6.c "Manual Fire Control Systems- Enclosed Machinery Areas" recommends dry chemical fire extinguishers and these are provided in each enclosure.
13.3.4 API RP2030 specifically discusses the hazards of attempting to suppress a
Page 11/14
Chevron
~ liiiiJ
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
.
flammable liquid or gas fire with water in two sections:
REV: 1 Page 12 of14
6.4 EXTINGUISHMENT . ... Extinguishment by water spray is generally most effective where the fuel is a combustible solid, water-soluble liquid or high flash point liquid. However, the risks associated with extinguishing certain fires should be carefully evaluated. Jf significant quantities of flammable gases or vapors are released a more hazardous condition with potential for explosive re-ignition can be created by extinguishing such fires instead of allowing them to burn at a controlled rate with appropriate surveillance and protection of surrounding equipment.
7 .2.3 Extinguishment. Extinguishment is seldom the primary purpose of water spray system installations in the petroleum industry ... It should be noted that extinguishment of low flash point hydrocarbon liquids with water spray is seldom possible and not necessarily desirable. A key question during hazard analysis is "Jf the material is extinguished while still generating vapor, is there a risk of vapor cloud re-ignition?" (The answer is yes at this facility.)
13.3.5 API Publication 2510A is primarily geared towards the liquefied Petroleum gas industry, but has relevant information for fighting pressurized gas fires.
Per Table 5- Water -Application Methods:
.. One disadvantage of water deluge and water sprays is that they .. . may not be effective for jet (torch) fires.
Also Section 5.5 Detection Systems gives general guidance on hydrocarbon vapor detectors, heat detectors and flame detectors. This facility includes all three systems, and complies with the guidance of this document.
13.3.6 Fire fighting and suppression standards in the oil and gas industry vary from standard industrial, high rise, and low rise practices. The engineering standards employed in the design of hydrocarbon equipment are conservative and attempt to contain hydrocarbon inventories within the equipment. However, in the event of a leak, the design of the external areas surrounding the equipment are designed to quickly isolate the leak, depressure the equipment, prevent the spread of the hydrocarbon leak, minimize the propagation of any fire event, maintain mechanical integrity through inventory liquidation without catastrophic failure, and minimize exposure to personnel and environment. Chevron SOPs require facility personnel to not engage in fire fighting beyond the incipient stage. The facility and the enclosures have been designed within these parameters.
Page 12 I 14
Chevron
• Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron
.
Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
Appendix A
1.0 GAS DETECTION SYSTEM OPERATING DETAILS
REV: 1 Page 13 of14
1.1 Each equipment enclosure is provided with a combustible gas detection system listed by a Nationally Recognized Testing Laboratory (NRTL) which exceeds the requirements of API Recommended Practice RP!4C. The gas detection sensor is wired to the facility Emergency Shutdown System (ESS).
1.2 When the gas detector in an equipment enclosure detects the presence of gas at 20% Lower Explosive Limit (LEL ), it performs the following functions:
• Indicates on the Human-Machine Interface (HM!) video screens in the Control Room
• Indicates on the HMI on the nine (9) outdoor Local Control Panels
• Activates a dedicated alarm on the audible alarm system
• The 24VDC control system on the skid remains energized, and the skid remains in operation.
1.3 When the gas detector in an enclosure detects the presence of gas at 40% LEL, it performs the following functions:
• Indicates on the HMI video screens in the Control Room
• Indicates on the HMI on the nine (9) outdoor Local Control Panels
• Activates a dedicated alarm on the audible alarm system
• Trips off the AC power feed to that enclosure's explosion-proofpanelboard at its source in the Electrical Building.
• Shuts off all hydrocarbon flow to the enclosure from the source outside of the enclosure
• Shutdown valves which shut off hydrocarbon flow are fail-safe, pneumatically operated, and will also close upon safety system failure or loss of air pressure to the fusible loop system.
• The 24VDC control system on the skid remains energized, but the skid remains shut off from hydrocarbon flow until the shutdown is manually reset by the Control Room operator.
1.4 The gas detection system shall be tested and recalibrated every 3 months in accordance with 30 CFR Chapter II Part 250.804 "Production safety-system testing and records." The gas detection system that is proposed will be certified by an NRTL to fully comply with this standard and with the system design details contained within API RP 500.
Page 13/14
Chevron
~ lliiiiiiill
Title: PICEANCE FIRE PROTECTION PHILOSOPHY Customer: Chevron Project: Piceance Basin Project Spec No: 2033-201-00-ST-0001 Date: 7 December 2008
Appendix B
REV: 1 Page 14 of14 II
1.0 EQUIPMENT ENCLOSURE FIRE DETECTION SYSTEM OPERATING DETAILS
1.1 Each equipment enclosure is provided with a pneumatic fusible plug loop fire detection system which exceeds the requirements of API Recommended Practice RP14C. A pressure transmitter, wired to the facility Emergency Shutdown System (ESS), monitors the fusible loop's pneumatic pressure.
1.2 When a fusible plug inside of the equipment enclosure melts in fue presence of a fire, fue pressure transmitter detects the Joss of air pressure in the fusible loop system and signals the ESS which performs the following functions:
• Indicates on the HMI video screens in the Control Room
• Indicates on the HMI on the nine (9) outdoor Local Control Panels
• Activates a dedicated alarm on the audible alarm system
• Trips off the AC power feed to that enclosure's explosion-proofpanelboard at its source in the Electrical Building.
• Shuts off all hydrocarbon flow to the entire facility
• Shutdown valves which shut off hydrocarbon flow are fail-safe, pneumatically operated, and will also close upon safety system failure or loss of air pressure to the fusible loop system.
• The 24VDC control system on the skid remains energized, but fue skid remains shut off from hydrocarbon flow until the shutdown is manually reset by the Control Room operator.
• Depressures the bulk of the natural gas process lines and vessels within the facility to the flare. (Some sections of piping and vessels outside of the building enclosures, such as the glycol reboiler, may have minor amounts of residual gas under pressure.)
1.3 Each of the enclosures rated for H-2 occupancy will also be equipped with triple infrared flame detectors ("fire eyes") per section 8.3 and pneumatic fusible loop system per section 8.2.
1.4 Because the enclosures are exposed to ambient weather and Class I, Division 1 conditions, and because there are no commercially available weatherproof smoke detectors rated for Class I, Division 1 service, smoke detection systems will not be installed in this facility. Instead, our design philosophy is to use gas detection to detect the presence of a potentially dangerous atmospheric hazard and, in parallel, to use two different technologies (triple infrared flame detection and pneumatic fusible heat detection.) We propose the API-RPSOO methodology of detecting the gases and shutting down the plant upon detection of dangerous levels of flammable gas.
Page 14/14
Inspection Report
COLORADO STATE ELECTRICAL BOARD
INSPECTION REPORT I CORRECTION NOTICE
Date Received: 08-FEB-1 0 Permit Number: 679981
Contractor/HomeOwner: SPECIALIZED AUTOMATION SERVICES LLC
Address:
Type of Inspection:
Action:
25-4, 2700 CLEAR CREEK RD
Complete Final
Accepted
Comments or Corrections: 1) battery covers 2) close rated enclosure 3) 408.4 Circuit Directory Every circuit to be identified as to its clear, evident, and specific purpose or use includes spares 4) Installer on site making corrections
Inspectors Name: Cyrus T uchscher Phone Number: 970-625-5085 Date: 08-FEB-10
COLORADO STATE ELECTRICAL BOARD DEPARTMENT OF REGULATORY AGENCIES
1580 Logan St. Suite 550 Denver, Colorado 80203-1941
Phone: (303) 894-2985
https://www.dora.state.co.us/pls/real/Ep_ Web_Inspection_GUI.Process_Page
Page I of I
2/9/2010
- • •• • ,_,....,.r-.11'-JI"
19.814 G. H. Circle
l'>!~nt r.~~.!Un,3Mdf~U!
p,O. Box 1178
Waller, Texas 77484
itle)lhonc ih.>!
NTA,Inc. 574-773-7975 Mailln!J Ad:ITisll: FlU 1/o:
305 North Oakland Av, Nappanee, IN 46550 574-773·2732
)( 20031·Goda Compliant . Live Roof Load ~ 5'"{L__ PSI' Floor Design Load
Wind Design Speed
/JS PSF
9'o MPH.
Fira Rating: Ex!ari .. orWalls Floor AI& Goillng.&/J
Fee Schedule Total footage Amount Model Name/No.
AnnunJ l'lt!gislrozioh Fcl!!tnusl l:a at:t:ompilnli:tl ,t ;r"qU .. ;,r'<J 5 Lrd ,?.R ,..r c. by new/upd:.ted OC: M2nUi!l)
i /.9.t.t.Y4.o.r »G :Mtnlmuril !.to~ma:dm\lrn 3 copies) •
S500,001par lcc:;:illon
f'' :~·· <:~·c-~·-~:rc·cJ tcq cnJc:ulaloi-lor Plaq.P,pptovllJ~r-<Utili lqunre foolilno x f;ScJor fndtcBttid billow:
FEB (/ 6 2009 ·J;tri Ap(ltuVIII Fno- .$0.2Sfsq.ft,
. . ...
ck~tkw,'; i.!nirrium 2 sets-maximum 3 t:el$) L
ddttlonaf Pli!ll Sttl~ ~0.10/:~oq,.ft. 'P-Fed Ex or UPS No. .(If ovem1 t , • .;::';·:
4"/,:;;:CJ shipping or approved plans_raEjuestcd) .
i'nlmuril P"l!o ror }:'JnJ1 Approvnb-. $1GD.oo
# :2 99'/'-c?.:l/2/-, m Rovl:~lanv ft:l;10/.:~qJL ------------·-·
Plan Approval Number
11m urn feDf~r Phm AIWi:slon,_ $50,IJO 1.uu:h 5lfLfL(
)TAL AMOUNT SUBMITTED: ~c:;o EXPIRES: I I J /:Z()/. 0
NUFAG)URER CERTlF!ES !hill ®l.Y Jl:ppriwCd equlpm_enl <Hid mall!tfaJs wl!l be us&~:~ and lt\13 frc;!.a!lal!on.s shnJr l::c: made Ill a!XOI'dance ~W.h apJl(oVed pl3ns
appf!e:.tbl1t coaes Ond Provi::IPfls Dllhe Coloroda Divlclon ol Housing, MantJiat:ltm!r agre-es IO li!·plan! Jnspe-t:llon of uni!s manulaclurod IJ!lll"er Ulll above p!tm oval. Applic3Uon zhaJI b(t ma~ for and ltlsrgh;.a ·al~ed lo ll!l)d! rJK:!wy bWI non resldenlJaJ lhnt Is subjecl to Colorado slalutes and whkh is ma!'lUfae.lll!t!d or Is !o bC!
or offered tt>t Sale 1t1 the Sia!e- of Colcrat'o •
. OF HOUSING, 1313 SHERMAN STREET. RM 321, DENVER, CO. 8020~ 1303) 866-4616 Fax 866-3072
Parcel Detail
Garfield County Assessor IT reasurer Parcel Detail Information
Page I of 5
Ass~A~or/T rea~j.)rer Jlmperty_ful[!rch I Ass_~ssoLS!!bset Uuer:y I Asse_~§Or Sales s_~(!rch C.Lerkli Recon:llli' Rec~ption Se[!rch
Basic U~llding_Gbf!c~cteri~tt~A I T axJnforma:ti1:m
Parr;_elQetail I · Yalue O_~tail I SJ!les Det(!H I H!l~identiai/Ggmmercial Lmprovement.D~tail l.aod_.DetaU I Prrot!!J]rf!pb_~ I MiJLL~vy Rev_enues Detail
IT ax Area II Account Number II Parcel Number 112£1£18 Mill Levy I I D29 II R29D444 II 21391S3DODI4 II 32.108 I
Dwner Name and Mailing Address
jCHEVRON USA INC jC/0 CHEVRON TEXACO PROPERTY TAX IP 0 BOX 285 jHOUSTDN. TX 77001
Assessor's Parcel Description (Not to be used as a legal description)
jSECT.TWN.RNG:IS-5-98 DESC: SEC.7: jTHAT PT OF LOTS 12.14 AND NESENE jLYING DESC: BELOW THE ESCARPMENT j(NET 14.20AC) ALSO THAT PT OF DESC: jTRS. 50.51 AND 56 LYING BELOW THE jESCARPMENT (NET DESC: 175.17). jSEC.8: THAT PT OF LOTS 2.4.7.8.
http:/ I www.garcoact.coml assessor I parceLasp?ParceiNumber= 21391 S300014
I' I I I
I I I I I I I
214/2009
Parcel Detail Page 2 of 5
ISWNE. NW. DESC: NI/2SW. WI/2SE. I jLYING BELOW THE ESCARPMENT (NET I jDESC: 222.84AC). SEC.I7: THAT PT DT I jLDTS 1(23.16). 3( DESC: 8.57). I 14(8.60). 5(11.84). 6(15.00). I j7(13.64). OESC: (80.81 TOTAL /73.0 I jNET) LYING BELOW THE ESCARPMENT I jDESC: ALL OF TRACKS 80(160 AC). I 1110(110 AC). 111(160 AC) DESC: AND I ITHOSE PARTS OF THE FOLLOWING TRS I ILYING BELOW OESC: THE ESCARPMENT. I ITRS. 57(117). 60(35). 62(46). 84( I IDESC: 118). 83(80). 81(120). I 182(24). 87(46). 79(73). 88( DESC: I 145). 90(58). 77(103). 91(53). I 176(118). 75(116). DESC: 92(52). I 193(76). 94(121). 113(121). I 1112(137). DESC: 6-98 TR. 41(160). I lAND THAT PART OF TR. 109(106). I IDESC: LYING BELOW THE ESCARPMENT I IAKA: LUCKY STRIKE #9 DESC: GLEN I IBEULAH. GEN. JOFFRE #3 S 4 AND I ITHOSE PARTS OF DESC: THE FOLLOWING I ILYING BELOW THE ESCARPMENT: GEN. I jDESC: JOFFRE 2.5-14. LUCKY STRIKE I j4-8.10-14. AND GEN. DESC: PERSHING I 11 S 2. SUC:R290037 BK:0472 PG:0361 I jBK:0445 PG:0360 BK:I655 PG:I78 I jRECPT:666845 BK:0858 PG:0942 I
http:! I www.garcoact.coml assessor I parcel.asp?ParceiNumber= 213816300014 21412008
Parcel Detail
Location
I Physical Address: IITWN 5 RGE 98 SEC IS I I Subdivision: I
I Land Acres: 112840.21 I I Land Sq Ft: I D
I Section II Township II Range I I IS II 5 II 98 I
2008 Property Tax Valuation Information
II Actual Value II Assessed Value I I Land: II SD.3DDII
I Improvements: II Dll
I Total: II SD.3DDII
Most Recent Sale
II Sale Date: I IF=====s=al=e P=r=ice=1:j
Ad ditjJ! n alliJg~D etai]
Basic Building Characteristics
Number of Residential io Buildings:
Number of Comm/lnd jo Buildings:
No Building Records Found
http:/ I www.garcoact.coml assessor I parcel.asp?ParceiNumber= 21391S300014
17.49DI Dl
17.49DI
I
I
Page 3 of 5
21412009
Parcel Detail Page 4 of 5
Tax Information
j Tax Year IJ Transaction Type II Amount I
I 2008 II Tax Amount II $5SI.5BI
I 2007 II Tax Payment: Second Half II ($252.48)1
I 2007 II Tax Payment: First Half II ($252.48)1
I 2007 II Tax Amount II $504.921
I 2008 II Tax Payment: Second Half II ($23S.2D)j
I 2008 II Tax Payment: First Half II ($238.20)1
I 2008 II Tax Amount II $472.401
I 2005 II Tax Payment: Second Half II ($300.99)1
I 2005 II Tax Payment: First Half II ($300.99)1
I 2005 II Tax Amount II $801.981
I 2004 II Tax Payment: Second Half II ($343.98)1
I 2004 II Tax Payment: First Half II ($343.98)1
I 2004 II Tax Amount II $S87.9BI
I 2003 II Tax Payment: Second Half II ($420.50)1
I 2003 II Tax Payment: First Half II ($420.50)1
I 2003 II Tax Amount II $841.001
I 2002 II Tax Payment: Second Half II ($422.10)1
I 2002 II Tax Payment: First Half II ($422.10)1
I 2002 II Tax Amount II $844.201
I 2001 II Tax Payment: Whole II ($837.02)1
I 2001 II Tax Amount II $837.021
I 2000 II Tax Payment: Whole II ($871.9S)j
I 2000 II Tax Amount II $871.981
I 1999 II Tax Payment: Whole II ($1.080.28)1
I 1999 II Tax Amount II $1.080.28/
http:! I www.garcoact.coml assessor I parcel.asp ?ParceiNumber= 21381 S300014 21412008
8 7 6 5 3
JJ!IIa.
APPROVED SUBJECT TO NOTED
U:CEI"TTONS & INSPECTIONS GARFIELD COUNTY
BUILDING DEPARTMENT ~t(Woq By,.c:~:.!:L'tf~~
mLDCOPY NO IlllSl!'ECTION WITHOUT
'l'l!IESE PLANS ON SITE page of
1. REFEREMCE DRAWINGS; P8SR--59836AVF~CtNAY-I.IRS-oOGOO-<J0002-0D fiNISH GRADE PLAH.
2. PAl CENTRAL fACILITY PAD FJNJSII GRADING SI.IJ'ES e 2.0t.
3. CONTOOR INTERVAl: EXIST, CIJHOURS"' I' OESIGtt CONTOURS" I'
4. PAl PIPE RACK TO BE INSTALLED AFTER TilE RES(lVAl (f ALL CONSTRUCTION U.YOOIM IRAILERSISTRUtTURES
S. CONTRACHII SHALL CHECK ALL EXISTING C!IIDITIOHS ANO flt:LO VERiiY All DESIGN CCOiDINATES AND ELEVATIONS PRJ~ TO C~TRUCTJ[W,
SCALE: I INCH "' SO fEET
sp;,,,,,,,,y, sp·
Chevron ~ MidConTinent / Alaska SBU ~ Chevron North America lliijl Exploration and Production
1
D
c
B
"""
T o M
-MCBU
ISSUED FOR SPECIAL USE PERMIT
-
2
-
3
-
4
5
-
6
-
7
A I 8 I c I D I E I F
CHEVRON PRODUCTION FACILITY PICEANCE BASIN DEVELOPMENT GARFIELD COUNTY, COLORADO
LIQUID SEPARATOR SKID BLDG. MBD-1075 (PRE-FABRICATED BUILDING CONSTRUCTED BY J. W WILLIAMS)
\o I
';-
\o I
"'
r----
r-------- I I RIO BLANCO
COUNTY
J'-,_1
--- ~~te--Township 5S Range 98W S~oclion
~I ~ ~--~
~\. Rifle
Parochule
Sill
GARFIELD COUNTY I New Cos! I'!,..
Glenwood
~· \2!7 II lw 1-' L j
MES;------- ------- _ _j COUNTY PITKIN COUNTY
1 - - ----------------- - - i
DeBeque V Exit 62,/
"'-sEE VENDOR DRAWINGS fOR PRE-FAB BUILDING~
FOR STAIR AND HANDRAIL DEfA!LS--.. SEE DWG. 2033-30-C1-1 109-XX
i:: :z: ::> 0 u
I= ::> 0 a::
s~ILDING ELEVATIONS
~7RO!ECT ASS(lCiATES
L----------------------------------------~
I G
SITE OWNER: Chevron North America Exploration &: Production
I H
ENGINEER: Rolla Wottinger Project Engineer Project Associates, INC 1!999 Koty Fwy, Suite 607 Houston, TX 77079 281-556-6864 x211
CONTRACTOR: Elk Hom Construction
BRIEF SUMMARY OF THE PROJECT: Without force and effect on the contract documents, the poject may be summarized as follows: The construction of a 35' x 14' prefabricated, single story skid-mounted building on o concrete foundation,
AREA CALCULATIONS: Total Lot Area >100 acres Enclosed Building Area 490 sq.ft. <1 % Total Building Covered Area 490 sq.ft. <1 %
I
ZONING: RESOURCE/LANDS {GENTlE SLOPES, LOWER VALLEY FLOORS)
OCCUPANCY: H-2 CONSTRUCTION TYPE: V-B DESIGN CRITERIA: IBC-2003, IFC-2003
IMC-2003, IFC-2003, IECC-2003
SPECIAL INSPECTION REQUIREMENTS: WElDING:
1.) VJSUAL INSPECTION OF WELDS PER AWS D1.1 CONCREIE:
I J
DRAWING INDEX: PRE-FAB BLDG STRUCTURAL DRAWINGS: FOUNDATION LOCAllON PLAN GENERAL CML NOTES MBD-1075 UQUID SEPARATOR FOUNDATION CML PLOT PLAN BUILDING ENCLOSURE FRAMING DETNL SHEET 1 OF 3 BUILDING ENCLOSURE HOUSING DErAIL SHEET 2 OF 3 BUILDING SUGGESTED UFllNG DETNL SHEET 3 OF 3 GENERAL BUILDING DETNLS ENERPAN BUILDINGS SKID FOR UQUIO SEPARATOR ASSY. SHEET 1 OF 3 SKID FOR UQUID SEPARATOR ASSY. SHEET 2 OF 3 SKID FOR UQU!D SEPARATOR /JSSf. SHEET 3 OF 3
PRE-FAB BLDG ELECTRICAL DRAWINGS: CENTRAL FACIUTIES PLOT PLAN AREA CLASSIACATION PLAN SHEET 1 OF 2 AREA CLASSIACATION PLAN SHEET 2 OF 2 35KV SWITCHGEAR ONE-UNE SHEET 1 OF 2 35KV SWITCHGEAR ONE-UNE SHEEr 2 OF 2 4801' SWITCHGEAR ONE-UNE SHEET 1 OF 2 4801' SWITCHGEAR ONE-UNE SHEET 2 OF 2 4801' MCC ONE-UNE SHEET 1 OF 2 4801' MCC ONE-UNE SHEET 2 OF 2 5KV SWITCHGEAR ONE-UNE SHEET 1 208/120 VAC PANElBOARD SCHEDUUES SHEET 1 ARE, GAS, & ALARM SYSTEMS BLOCK Dl'.GRAM SHEET 1 ARE, GAS, & ALARM SYSTEMS BLOCK Dl'.GRAM SHEET 2 ElECTRICAL KEY PLAN ElECTRICAL PLAN AREA-85 ElECTRICAL PLAN AREA-86 GROUNDING AND UGHllNG KEY PLAN GROUNDING AND UGHllNG PLAN AREA-85 GROUNDING AND UGHllNG PLAN AREA-86 UGHllNG lEGEND AND SCHEMATIC SHEET 1 UGHllNG lEGEND AND SCHEMATIC SHEET 2 UGHllNG lEGEND AND SCHEMATIC SHEET 3 UGHllNG lEGEND AND SCHEMATIC SHEET 4 UQUID SEPARATOR JUNCTION BOX UQUID SEPARATOR INSTRUMENT LOCATION PLAN UQUID SEPARATOR UGHllNG PLAN UQUID SEPARATOR POWER PLAN UQUJD SEPARATOR GROUNDING PLAN INSTRUMENT CONDUIT AND CABlE SCHEDUlE
1.) CONJRACT WITH ITSllNG lABORATORY TO PERFORM CCMPRESSIVE lEST ON AT lEAST ONE CYUNDER PER EACH 14 YARDS OF CONCRETE. {30DO PSI MINIMUM AT 28 DAYS)
2.) QA/QC TECHNICIAN TO VISUALLY INSPECT NUMBER AND PlACEMENT OF REBAR IN COMPUANCE WITH PLANS AND A.C.I. STANDARD PRACTICES.
HAZARDOUS MATERIAL DATA: lHIS BUILDING PROCESSES LARGE AMOUNTS OF NATURAL GAS STREAMS {UP TO 50 MM SCFT/DAY) WHICH CONTAJN 801H GASEOUS AND UQUID FORMS OF HYDROCARBONS. NO OlHER HAZARDOUS MATERIALS ARE UTIUZED NORE STORED IN lHIS FACIUTY.
I K
2033-201-30-CJ-1102-15 2033-201-30-CI-1101-01 2033-201-30-CI-1113-01 2033-201-30-CI-1102-01 66-20-H3PH-8LDG 66-20-H3PH-8LDG 66-20-H3PH-8LDG ENERPAN DETNLS 8-30-SKID 8-30-SKID 8-30-SK!D
2033-201-20-AP-0002-02 2033-201-40-AP-0001-01 2033-201-40-AP-0001-02 2033-201-40-EL -0011-01 2033-201-40-EL -0011-02 2033-201-40-EL -0012-01 2033-201-40-EL-0012-02 2033-201-40-EL-0013-01 2033-201-40-El-0013-02 2033-201-40-EL-0015-01 2033-2D1-40-El-0020-01 2033-201-40-EL -0060-01 2033-201-40-EL-0060-02 2033-201-40-EL -4203-01 2033-201-40-EL-4232-01 2033-201-40-EL -4238-01 2033-201-40-EL -4303-01 2033-201-40-EL -4332-01 2033-201-40-EL-4338-01 2033-201-40-PL-4301-01 2033-201-40-PL -4301-D2 2033-201-40-PL-4301-03 2033-201-40-PL-4301-04 0706-0100 0802-0101 0802-0102 0802-0103 0802-0104 080208-CS-MBD-1075
HO llY REVISION DESCRIP'llON DATE CHK APP
A ROS ISSUED FUR Rf:VIEW 09/16/01:1 ~ Chevron North America • Expoloration & Production MCBU
CHEVRON NORTH AMERICA PICEANCE FIELD DEVELOPMENT
CENTRAL FACILITIES
ORIC, tv.TE: 9/16/08
""""'"" PLOT stAl!:
PRAWN BY: CIVIL FOUNDATIONS DRAWING INDEX
' "' 2033 201 30 AR 1113 01
-
NOTES:
MATCHLINE N. 1138' -0"
c:.v·--,_.----..,.--v-'.,...-...,...-..v-v-v-v-v--v--·v-v-~~-HOLD -----------------------, ----------------------, I
MSD-1075 UOU!D SEPARATOR SKID
owe. NO. 1113-0l
~--------------------
I I I I I I I I I I I I I I I
.J "' -------;:----------;:·--;:-:;:::~;;z-.J
I N 0
SEE DWG. 1102-11
L HOLD
MBF"-1070 FUEL CAS SKID DWG. ON 11 14-01
0
' "' 0 N
,, ,---1 )
~ :< I I ):<>
N. 1115'-0'' ~ ___ ~
.A. N 0
0'------------·-------·--------------------~-----·------------------------------·--------------------·---------·--·---------------·-------------·--------------------------' 0 61 16 t:JI I t:J ~ PIPE RACK ... ------------------ ·····------------------ ···------------------- -p~~-;,_~;--~i
0 0 ;: I I ;::' wr-----------·--------------------------------·-------------------------------------------------------------------------------------------------------------,·w ~~--------------------------------------------------------------------------~--J_ ______________________________________________________________________ ~~ ~ ~ I I
g ~ ~ g ~I ~~ ~~ ~~
I ::1 ::1 I d 0 R' ~ •I ~ s, s,
ZZZ-4003 ~~ COMPRESSOR BUILDING ~~ ,, OWG. NO, 1103-01 ::;; ~~ ~I
~ II ~I ~ w ;j
•l ~~ m M ;,;;1.1 ~1.1
Mlm M1• 0~ 0~ ~£ ~~ ~~ ~~
_......J.t-- t MATCHLINE N. 1068'-0" SEE DWG. 1102-19
'
ISSUED FOR CONSTRUCTION
.,. DAlE: 08129/0S __ _
CHEVRON AMERICA PICEANCE FIELD DEVELOPMENT
CENTRAL FACILITIES 1. SKID SIZES ARE PPPROXJMAlT. SEE SKID
FOUNDATION DRAWINGS fOR DeTAILS. FOUNDATION LOCATION PLAN
A 8 c D E F G H J K
PICEANCE FIELD DEVELOPMENT DESIGN CRITERIA AND CIVIL[STRUCTURAL GENERAL NOTES
REINFORCEMENT BAR TENSION SPLICE TABLE*
GENERAL INFORMATION DIAMETER
CLASS B SPLICE CLASS 8 SPLICE TOP BAR SPLICE TOP BAR SPLICE BAR SIZE LENGTH, IN. LENGTH IN LENGTH IN LENGTH IN
1. PRQJ~QT SCOP!,;: THESE STRUCTURAL DRAWINGS MAY ONLY BE USED TO CONSTRUCT THE 3. FOOTIN~ db In 3000 PSI 4000 PSI 3000 PSI 4000 PSI PROJECT LOCATED AT PICEANCE DEBEOUE, COLORADO. A. BOTIOMS OF FOOTINGS SHALL BE A MINIMUM OF 3' -0" BELOW FINISHED GRADE. CONCRETE CONCRETE CONCRETE CONCRETE
4. GRADE B!;AMS: 3 3/8 16 16 17 16 I 2. BUll DING C..QQJ;:; THESE PlANS HAVE SEEN PREPARED IN ACCORDANCE WITH THE INTERNATIONAL
A. PROVIDE A MINIMUM SIX-INCH VOID BETWEEN THE BOTIOM OF BUILDING CODE, (200.3 EDITION). ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH THIS GRADE SEAMS/FOUNDATION WALLS ANU UNDERLYING SOILS. 4 1/2 17 16 22 20 COD£ AND GARfiELD COUNTY, COLORADO REQUIREMENTS. 8. BOTIOMS OF GRADE BEAMS SHALL BE A MINIMUM OF 3 FEET BELOW FINISHED GRADE.
3. DESIGN LOADS· THESE STRUCTURES ARE A CATEGORY II STRUCTURES IN ACCORDANCE WITH TABLE 1604.5: c. REBAR SPLICES FOR TOP STEEL TO OCCUR AT MIDSPAN BETWEEN FOOTING LOCATIONS, UNLESS 5 5/8 21 16 28 24 NOTED OTHERWISE.
A. DEAD LOADS ARE IN ACCORDANCE WITH SECTION 1606. MINIMUM ROOF DEAD LOAD IS 15 PSF. 0. HOLES IN SILL PLATES FOR ANCHOR BOLTS SHALL BE SNUG TO PREVENT WALL MOVEMENT. 6 3/4 26 22 33 29 8. LIVE LOADS ARE IN ACCORDANCE WITH SECTION 1607. PROVIDE ADDITIONAL NAIUNG AT JOIST SILL PLATE CONNECTION TO PREVENT SLIPPAGE. c. SNOW LOADS ARE IN ACCORDANCE WITH SECTION 1608: 7/8 37 32 49 42 TO 7000 FT. 40 PSF 5. CoMe~QTED Fl!.b · 7
7001 FT. TO 8000 FT. 50 PSF USE ONLY APPROVED NON-EXPANSIVE, GRANULAR MATERIAL FOR FILL AS RECOMMENDED BY THE 8DD1 FT. TO 90DO FT. 75 PSF A. 8 1 43 37 56 48
9001 FT. TO 10,000 FT. 100 PSF SUPERVISING GEOTECHNICAL ENGINEER.
(IN ACCORDANCE WITH SECTION 7 OF ASCE 7) 8. ALL SUBGRAOE COMPACTION SHALL BE AS DIRECTED BY THE GEOTECHNICAL ENGINEER.
9 1 1/8 53 46 69 60 SNOW FACTOR: 1.0 6. EXTERIOR GRADE:
1 1/4 65 57 85 74 (IN ACCORDANCE WITH BUILDING CLASSIFICATION) 10 UNBALANCED SNOW LOADS PER SECTION 7.5 OF ASCE 7 A. SLOPE PERIMETER GRADE AWAY FROM BUILDINGS AT 6 INCHES IN THE FIRST 5 FEET, OR AS RECOMMENDED DRIFTING SNOW LOADS ON LOWER ROOFS PER SECTION 7. 7 OF ASCE 7 BY THE GEOTECHNICAL ENGINEER. 1 3/8 78 65 102 88 DRIFTING SNOW LOADS ON ROOF PROJECTIONS PER SECTION 7.8 OF ASCE 7 11
D. FROST DEPTH SHALL BE 36'" TO ELEVATION 800D FEET AND 42" ABOVE ELEVATION 8000 FT. 7. Atj(;HOR flO!.T::i: E. WIND LOADS ARE IN ACCORDANCE WITH SECTION 1609 OF INTERNATIONAL BUILDING CODE, 2003
FOR EQUIPMENT, STRUCTURAL STEEL AND PIPING ANCHOR BOLTS SHALL BE ASTM F1554 GRADE .36, UNLESS *IN ACCORDANCE WllH ACI 318-05 FOR CLASS "8'' SPLICES USING GRADE 60 REINFORCING STEEL .
EO!TION, WHICH REFERS TO SECTION 6 OF ASCE 7. A. *SPLICES SHALL BE STAGGERED AT LEAST 24". WIND VELOCITY 90 MPH OTHERWISE NOTED ON THE DRAWINGS. NUTS SHALL CONFORM TO ASTM A563 GR. A HEAVY HEX. WASHERS
UNLESS NOTED OTHERWISE, CONCRETE PROTECTWN FOR REINFORCING SHALL BE AS FOLLOWS : EXPOSURE CATEGORY C SHALL BE ASTM F4.36 ANCHOR BOLTS, NUTS AND WASHERS SHALL BE GALVANIZED IN ACCORDANCE WITH A153. 6. WIND IMPORTANCE FACTOR 1.15 B. WHERE INDICATED ON THE FOUNDATION DRAWINGS, HEAVY EQUIPMENT ANCHOR BOLTS SHALL BE A1CONCRETE DEPOSITED DIRECTLY AGAINST GROUND : 3" CLEAR. (IN ACCORDANCE WITH BUILDING CLASSIFICATION) ASTM F1554 GR 105 WITH ASTM A194 GR 2H NUTS AND ASTM F436 WASHERS UNLESS OTHERWISE NOTED. B CONCRETE EXPOSED TO EARTH OR WEATHER AFTER REMOVAL OF FORMS: 2" CLEAR FOR #6 BARS & HEIGHT AND EXPOSURE COEFfiCIENT AS PER EACH AREA. DO NOT GALVANIZE. LARGER ; 1 1/2" CLEAR FOR #5 BARS & SMALLER UNLESS NOTED OTHERWISE ON DESIGN DRAWINGS.
F. EARTHQUAKE LOADS ARE IN ACCORDANCE WITH INTERNATIONAL BUILDING CODE 2003 WHICH ALLOWS c. UNLESS OTHERWISE NOTED ON THE FOUNDATION DRAWINGS REFER TO TABLE 1 FOR STANDARD ANCHOR BOLT 7. REINFORCING BARS SHALL NOT BE HEATED, STRAIGHTENED OR RE-SENT WITHOUT THE APPROVAL OF THE USE OF THE ASCE 7-05 CODE. THE ASC 7-05 CODE WILL BE USED. THREAD AND SLEEVE LENGTHS.
DESIGN ENGINEER COLO BENDING OF REINFORCING STEEL SHALL BE IN ACCORDANCE WITH ACI 318. SITE CLASS 0 TABLE 1 MAPPED SPECTRAL RESPONSE ACCELERATIONS, Ss AND S1 43.6%, 9.1% 8. THE FABRICATOR SHALL SUBMIT EACH OF THE REBAR PLACEMENT DRAWINGS & ACCOMPANYING BAR LISTS
SPECTRAL RESPONSE COEFFEC!ENTS, Sos AND So1 70%, 13% FOR APPROVAL THE FABRICATOR'S PLACING DRAWINGS SHALL BE REFERENCED TO ENGINEER'S DESIGN SEISMIC DESIGN CATAGORY D BOLT ALLOWANCE FOR NUTS THREAD SLEEVE DRAWINGS. BAR LISTS SHALL BE REFERENCED TO THE RELATED PLACING ORA!fii!NGS. THE ENGINEER OR ITS DESIG~ BASE SHEAR 0.105 w RESPO SE MODIFICATION FACTOR, R
giMPLIFIED PROCEDURE PER DIAMETER (Unless Otherwise Noted) AT TOP (If Req'd)) STD. LENGTH DESIGNATED REPRESENTATIVE , !fii!LL REVIEW THE FABRICATOR'S PLACING DRAWINGS & BAR LISTS WITH
ANALYSIS PROCEDURE USED IBC 1617.5 d. RESPECT TO CONFORMANCE TO THE DESIGN DRAWINGS. ONE COPY IN!ll BE RETURNED TO lHE FABRICATOR P1 & LENGTH L APPROVED OR WITH NOTATIONS REQUIRING CHANGE. IN THE LATER CASE , THE FABRICATOR SHALL CLEARLY 4. CONSTRUCTION MEJ:HQQ· N1 N2 THREAD
SHELL SIZE MARK SUCH CORRECTIONS AND RESUBMIT THE DRAWINGS FOR FINAL APPROVAL . APPROVAL Of REBAR
A. THE STRUCTURAL DRAWINGS REPRESENT THE FINAL STRUCTURE. THE DRAWINGS DO NOT INDICATE _LENGTH-~" ----~··--~---·-"·"-"" ~-( U.11!.~-~;>._QJ:.b ~!.\'li$_!0! _..I:I!:M$:1 ) -·-·-- - ·· -PLACEMENT· ORA WINGS-&·-BAR-··t!STS --sY-ENGINEER-WJLL -NoT-"REtiEVE· F ABR!CA TOR -oF-RESPONSIBIUTY-"FOR··~ --- -····-~ -- -·--
---· ·-·· -THE···CONTRACTORsr·-·-MEANS,-··METHODS; ··TECHNIQUES;· ·sEQUENCEs· ·oF···coNSTRUCT!ON -AND -~JOB--SITE---~~--~-- AT THE COMPLETENESS & ACCURACY OF All THE DIMENSIONS & DETAILS. SAFElY. THE ENGINEER OF RECORD IS NOT RESPONSIBLE FOR THE CONTRACTOR'S FAILURE NOR BOTIOM 9. ALL EXPOSED CORNERS ABOVE GRADE SHALL HAVE A 1" CHAMFER .(NOTE: MANY MAT FOUNDATIONS WILL IS THE ENGINEER OF RECORD RESPONSIBLE FOR ECONOMIC LOSS AND/OR DELAYS OF THE CONTRACTOR OR SUBCONTRACTORS, 1/2" 1" 1/2'' 1" 2 1/4" 2" X 5" 1'-0" HAVE EXPANSION JOINTS WITH PAVEMENT ABUTTED. lHESE Wlll BE TEMPORARY EXPOSED PRIOR TO THE
B. ALL CONSTRUCTION SHALL BE ADEQUATELY BRACED TO PREVENT 1 1/4" 2" 1" 2 .3/4" 2'' X 7" 1'-3"
INSTALLATION OF THE PAVEMENT BUT SHOULD NOT HAVE CHAMFERED EDGES.) DISTORTION AND DAMAGE DUE TO CONSTRUCTION LOADS AND NATURAL FORCES. 5/8"
10. IMMEDIATELY AFTER FORMS ARE REMOVED , THE FOUNDATION CONTRACTOR SHALL FILL ALL VOIDS TO .3/4" 1 1/2" 2 1/4'' 1 1/4" 3" 2" X 7" 1'-4" OBTAIN A STRAIGHT & fLUSH SURFACE. IMPERFECTIONS SHALL BE CORRECTED WllH GROUT & THEN All
5. TRADE COORDINATION: EXPOSED FOUNDATION COLUMNS, BEAMS & WALLS ABOVE GRADE SHALL HAVE A STONE RUBBED FINISH.ANY A. THE STRUCTURAL DRAWINGS ARE INTENDED TO BE USED IN CONJUNCTION WITH ARCHITECTURAL, 7/8" 1 1/2" 2 1/2" 1 1/4" 3 1/4" 2" X 7'' 1' -5" HONEYCOMBING SHALL BE CHIPPED & REMOVED TO SOUND CONCRETE PRIOR TO REPAIRING WllH GROUT.
ELECTRICAL, MECHANICAL, PLUMBING AND SITE DRAWINGS. CONFLICTS IN DIMENSION 1 3/4" 2 3/4" 1 1/2" 3 1/2" 3" X 10" 1'-10"
HONEYCOMBING REPAIRS THAT EXPOSED STEEL REINFORCEMENT SHALL BE DOCUMENTED & REPORTED TO AND INTERFERENCE SHALL BE DIRECTED TO THE ENGINEER PRIOR TO CONSTRUCTION. 1" THE ENGINEER PRIOR TO REPAIR & PLACEMENT .
6. SPECIFICATIONS· 1 1/4" 2 1/4" .3 1/2" 1 3/4" 4 1/4" 3'' X 10" 2'-0" 11. FOUNDATION CONTRACTOR SHALL VERIFY All DIMENSIONS AND EMBEDS PRIOR TO POURING FOUNDATIONS. CONTRACTOR SHALL CHECK ELEC, GROUNDING, FIREWATER & SEWER DRAWINGS AS MAY BE APPROPRIATE
A. IF CONFLICT ARISES FROM THE RECOMMENDATIONS OF THESE DRAWINGS AND THOSE CONTAINED 1 1/2'' 2 1/2" 4" 2" 4 3/4" 4'' X 15" 2'-8~ TO ENSURE All UNDERGROUND LINES ARE IN PLACE PRIOR TO THE POUR . PRIOR TO IMPLEMENTATION OF IN THE SPECIFICATIONS, NOTIFY THE ENGINEER OF THE DISCREPANCY PRIOR TO CONSTRUCTION.
FIELD MODIFICATIONS FOR CONSTRUCTION OR PLACEMENT ERRORS, THE ENGINEER OF RECORD SHALL BE 1 .3/4" 3" 4 3/4" 2 1/4" 5 1/2" 4" X 15" 2'-10" NOTIFIED IN WRITING FOR APPROVAL OF ALL FIELD DESIGN CHANGES. 7. OPENINGS:
3'-4" 12. FOUNDATIONS SHALL BE PLACED ON UNDISTURBED SOIL OR ADEQUATELY COMPACTED FILL PLACED IN A. OPENINGS, SLEEVES, POCKETS, ETC. SHALL NOT BE PLACED IN BEAMS, JOINTS. COLUMNS, ETC. 2" 3 1/4" 5 1/4" 2 1/2" 6" 4" X 18"
ACCORDANCE WlTH THE GEOTECHNICAL INVESTIGATION UNDER THE SUPERVISION OF A QUALIFIED INSPECTOR UNLESS SPECIFICALLY DETAILED ON THE STRUCTURAL DRAWINGS. NOTIFY THE ARCHITECT WHEN 2 1/4" 3 3/4" 6" 2 .3/4" 6 3/4" 4" X 18'' 3'-10" IF THE SOIL THAT SUPPORTS THE FOUNDATION IS TO BE EXPOSED OVERNIGHT, IT IS RECOMMENDED THAT DRAWINGS BY OTHERS SHOW OPENINGS, SLEEVES, POCKETS, ETC. NOT SHOWN ON THE
A 2'' SEAL SLAB BE INSTALLED AFTER THE SUBGRADE HAS BEEN INSPECTED TO ENSURE ADEQUATE STRUCTURAL DRAWINGS, BUT WHICH ARE LOCATED IN STRUCTURAL MEMBERS. 2 1/2" 4" 6 1/2" 3" 7 1/4" 6" X 24" 4'-2" BEARING CAPACITY FOR SOIL BEARING FOUNDATION .
8. EXISTING CQHJl!.Il.Q.!iS.; 2 3/4" 4 1/2" 7 1/4" .3 1/4" 8" 6" X 24"' 4'-4" 13. STRUCTURAL FILL SHALL BE USED AS BACKFILL AGAINST FOUNDA110N & TO RAISE GRADE. EXCEPT ASANI
A. THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS DEPICTED ON THESE DRAWINGS PRIOR TO CONSTRUCTION. INDICATED ON TI-iE PLANS FOR FROST PROTECTION FILL . FROST PROTECTION FILL SHALL BE A SAND D 3" 4 3/4" 7 3/4" 3 1/2" 8 1/2" 6" X 24" 4'-6" GRAVEL FILL CONFORMING TO THE GEOTECHNICAL RECOMMANDATIONS.THE FILL SHALL BE FREE
~ 9. STRUCTI JRA! lAYOUT: SIGNIFICANT ORGANIC , DELETERIOUS MATERIAL & SHALL HAVE AN EFFECTIVE PARTICLE 01 Q!)G:'Et>/Q
A, ALL CONCRETE & STEEL MEMBERS ARE CENTERED ON PLAN GRIDS UNLESS NOTED OTHERWISE. TiiAN 3'". ~ , •••• ~ ..... "'" 8. FOR DATUM ELEVATION SEE SEE '"BENCHMARK NOTES" DWG. 2033-101-30-C!-1102-02. STRUCTURAL MATERIALS 14. GROUT FOR EQUIPMENT & SASE PLATES SHALL BE AS NOTED: :-vC:····~ Q. 8(;~~
HAZARQOUS MATERIAL.Q8IA; PIPE RACK, SKID, AND MISC. SUPT. BASE USE CEMENT GROUT 0 ." "</ ,(>I 10. 1.0 CONCRETE: CONCRETE MATERIAL PLACEMENT AND TESTING SHALL BE ACCORDANCE WITH CONCRETE EQUIPMENT STRUCTURES - USE FIVE STAR GROUT OR APPROVED EQUAL Q .:;;· ''l'- a A. THIS FAC!UlY IS DESIGNED TO ACCOMMODATE APPROXIMATELY 50 MILLION STANDARD CUBIC FEET PER DAY
SPECIFICATION 203.3-240-30-SP-0004-01 UNLESS OTHERWISE NOTED ON THE DRAWINGS. VESSEL BASE PLATES - USE FIVE STAR GROUT OR APPROVED EQUAL : •
~J (MMSCFO) OF PRESSURIZED. WELLHEAD-QUALITY NATURAL GAS (I.E., NATURAL GAS THAT HAS YET TO HAVE EXCHANGER SLIDE PLATES- USE FIVE STAR GROUT OR APPROVED EQUAL ;0 ~¥259 WATER, CARBON DIOXIDE, AND NATURAL GAS LIQUIDS REMOVED PRIOR TO SHIPMENT AS PIPELINE 1.1 Qfl:l_ERAI BEQUIREMENTS: PUMPS LESS THAN 25HP - USE FIVE STAR EPOXY GROUT OR APPROVED EQUAL ~ C(. (\IV QUALITY NATURAL GAS). THE NATURAL GAS WITHIN THIS BUILDING IS CONTAINED WITHIN S~~EL PIPELINES
CONCRETE FOR ROTATING EQUIPMENT FOUNDATIONS (25 HP AND GREATER) SHALL BE PROPORTIONED PUMPS 25HP AND GREATER - USE FIVE STAR EPOXY GROUT OR APPROVE EQUAL .. ~Q ·, po_:-~NO ASSOCIATED PRESSURE-RATED VE55EL5 DESIGNED PER A5M~ "~~~ API 1.
COMPRESSORS AND TURBINES - USE FIVE STAR EPOXY GROUT OR APPROVE EQUA60:~;~~~ ·f? AZARDOUS'MATFR!i.i:s "AR'E sTORED NOR UTILIZED WITHIN "TillS 1 iNr.:,::.--THiS Js APPLICABLE FOR ALL H-:) TO OBTAIN A MINIMUM COMPRESSNE STRENGTH OF 4000 PSI ® 28 DAYS. . {"'"··' ~UPANCY :~~LOSURts. 2. ALL OTHER CONCRETE SHALL BE PROPORTIONED TO OBTAIN A MINIMUM COMPRESSIVE STRENGTH OF BOLT: ~<-,> ....... .-:; '-::;:.:--OT APPLICABLE FOR ENCLOSURES RATED OCCUPANCY FOR S OR U. ffi •. .3000 PSI AT 28 DAYS UNLESS NOTED OTHERWISE. SPECIFICATION OF THE CONCRETE STRENGTH FOR 1. ANCHOR BOLTS SHALL BE SET BY MEANS OF A TEMPLATE. REINFORCING STEEL MAY BE SPR ~~~A·~-~\\_;_~ J GENERAL CIVIL N SEAL SLABS MAY BE REDUCED TO 2000 PSI AT 28 DAYS.
TO ACCOMMODATE SLEEVES. REINFORCE SHALL NOT BE CUT. '-.4 -i2'1:CL""tJ-
) FOUNDATIONS 3. THE MAXIMUM NOMINAL AGGREGATE SIZE FOR FOOTING MATS & MASS POURS SHALL BE 1 1/2"' DIA. 2. USE PRECAST "PB" OR "DB" CONCRETE BAR SUPPORTS TO SUPPORT REINFORCEMENT Sl~Mt5Arr-:: ( - -31-1 1. GEOTECHNICAL INVESTIGbi.!Q!i; THE MAXIMUM NOMINAL AGGREGATE SIZE FOR POURS ABOVE MATS SHALL BE 3/4" DIA. 3. CLASS "B" LAP UNLESS NOTED OTHERWISE. ·- . C:. )
A. A GEOTECHNICAL REPORT BY GEOTECHNICAL ENGINEERING GROUP, INC. OF GRANO JUNCTION, CO, DATED 4. ALL REINFORCING STEEL SHALL CONFORM TO ASTM A615/615M GRADE 60 ( 420MPo). 4. NO ADDITIONAL REINFORCING IS REQUIRED IF OPENING !S LESS THAN 12" DIAMETER.
APRIL 27, 20D7 (JOB NO. 2628-G) IS AVAILABLE. THE CONTRACTOR SHALL FAMILIARIZE HIMSELF WITH ALL 5. UNLESS OTHERWISE NOTED REINFORCING STEEL SHALL BE SPUCED AS FOLLOWS : 5. EMBEDDED ITEMS SHALL HAVE A MINIMUM OF (2) ANCHORS. OF THE REPORT REQUIREMENTS. THE FOLLOWING DESIGN PARAMETERS HAVE BEEN DEVELOPED BASED ON 6. AU. EMBEDDED STEEL THIS DRAWING SHALL MEET ASTM A36. UNLESS OTHERW!SED NOTED. THIS REPORT. THE MORE STRINGENT REQUIREMENTS SHALL APPLY. IF CONDITIONS DIFFER FROM THOSE A) COMPRESSION SPLICES: 30 BAR DIAMETERS MINIMUM, BUT NOT LESS "THAN 12". 7. ALL EMBEDDED STEEL SHAI.L BE FINISHED AFTER FABRICATION AS SHOWN ON THE PROJECT DESIGN PRESENTED HEREIN, THE ENGINEER SHALL BE NOTIFIED BEFORE CONTINUATION OF THE WORK. B) TENSION SPLICES: SHALL BE CLASS "B" IN ACCORDANCE WITH ACI .318 (SEE SPLICE TABLE) ORAWlNG.
C) MINIMUM LAP FOR WELDED WIRE FABRIC SHALL BE ONE FULL MESH PLUS 2" BUT NOT LESS THAN 12" 8 . DIMENSIONS ON PROJECT DESIGN DRAWING ARE BASED ON FORMED CONCRETE. CONTRACTOH MUST 2. . S.ffiE&LE.QQI.!.tffi.S; 0) LONG MAT SPLICES TO BE STAGGERED I.E. NO MORE THAN ONE HALF THE BARS TO BE SPUC£0 AT OBTAIN WRITTEN APPROVAL FROM THE ENGII\I·Di PRIOR TO USING EARTH FORMED A. FOOTINGS SHALL BE DESIGNED FOR A NET ALLOWABLE SOIL BEARING PRESSURE AS GIVEN BY THE THE SAME LOCATION. CONSTRUCTION.
GEOTECHNICAL ENGINEER AT THE V/II~IOUS LOCATIONS IN THE PROJECT. 8. SUBGRADE SHALL BE INSPECTED AND SIGNED OFF BY A COLORADO STATE REGISTERED GEOTE:CHNICAL
ENGINEEH TO VERIFY THE ABOVE BEARING C/lf'ACITlES IMMEDIATELY PRIOR TO CONSTRUCTION OF THE FOOTINGS.
" " REVISION O(SCRIPTIOI-/ DATE '"' ~ e Chevron North America CHEVRON NORTH AMERICA & ' "' ISSUEO f'OR CONSTRUCTION 08/08/08 Exploration & Production MCilU PICEANCE FIELD DEVELOPMENT EPS
I+ OCM RfYlSEO GENERAL INI'ORMATION NOTES 08/19/08 CENTRAL F AGILITIES ISSUED FOR CONSTRUCTION REVISED ~ ..
1--'- REVlStO __ gENERAL INI'ORMATION NOTE #10 ! 1/1Jj06 ew MH OWG. SCAl(: NONE DRAWN BY: PA! (ES2) GENERAL CIVIL NOTES
I~PROJECr- OIIIG. DATE: !2/27/07 CIIECXCO OY: " DATE: ___..l_lLULOB ··-f'I!OJECT Af(: AI'PROV£0 11"1": MH/MM SHDETI DRAWING NUMB£11
1101_
01 I R2V ASSOCIATES 1»' ""~""'"~o • <"'~lR~O- =~<lOS."" ""' w. "''" ""'" p,_ (1><1 ,,.._ .. ,. PLOT SCAL£: PLOT DAlE: 2033 201 30 Cl-1 1 ,,. .. , ... 00. '""" l"''"~'"" . ~:;...
I I) (II flU:O , o~ea;oa l.l:<l '" OM> ~~----- '''• " ee•• "'" "" • ... ,
A I 8 I c I D I E I F I G I H I I I J I K
CPf NORTH 37' -1 0" 0/0 FOOTING
/''"' ~~ .15' -0" 0/0 SKID LENGTH
r 3' 0" 14'-6" 14'-6" 3' 0"
/; ~ ~ <ri < ,,
"' ...,
I I ' I I y- /- SE£ DWG. 2033-201-30-CI-1101-03
I
N - (6) 3/4"¢ ANCHOR BOLT DETAILS
::--
7 "' " 7 1:: N. 1132' 0" EoGF. of SkiD 'v (f; -~ _/ t A.B. -
' ~ 1Y .•.
--"' "
b ' I: ;... ~
;, L 1-- w -y ::-0
I I I I ' I I "' 0 ~ I
l I z 0
;= ~ 0 0 0 ~ ~ 0 ~
' 0 - - - - - - - -0
' I I b 0
b I ' ' .... 1---"' ~- ol ol
<-<
----~-~ 52
> ~I ~I '" ... - ·- ~- _______ , ___ ,, ____ " -------·---·----·----·· -- ---- ----· ---S· - ... - 0 - ------------------------·- ------ -·---·~---~--~-----·-·--·- __________ ,., --- ----·-------~------ --· --r ·---- ---- -o-- ------ -·· ~----- ---- --------·· --- -·- -
I c; w
"' 0 0 0 I I 0
'" w
:,., -t~
"" r::r:rrTr'J-
- ~DO UCf::: ;, 4
<;l.,r''_,. ·~... •• '/I. MBD-1 075 LIQUID SEPARATOR FOUNDATION PLAN ) 0/' 0 8(/''·. <~ > • ~ . ,<) •
SCALE: 1/2'',1'-o" (}/:jy' I"?\ \'0 ' - O'" o·.C. ci ~~Q :2'; •'·'·'-~ "' %\·~~ >if· " "-
~
"' 0
"' ::-r~CH FACE?
'-·~·· /-'~ 0
'<:,. &,:·: .. ······;:;\~;) n ';.., I 15/16"
- ;2,h)J<,Jl\\_ \ .. ~ T.O.C. EL. 3' 8 - ".d I. ~ALL STANDARD <Q:z;:.:_y..z:;:.r. ~· FIN. GR. El. 3'-4 15/16" • • •
~~~- II' 90' HOOKS DATE 07-31-10 '~ "" ''" ~- r EXP.
COMPACTED ~ QW STRUCTURAL FILL - 'n I ~5 @ 12" @ ;:;5~
;-, ±) o.c. ~ .._,u,_ I ~ -- r-::. -- ·--~ EACH FACE)__.- ,-- I • ,. t-- oo~~-~0 ~~ l~gggl l\JY~.) REBAR FOR GROUNDING -<-<
' @ EACH SIDE OF FDN. I • • 0 0 I SEE owe. 1101-03
- "• = \. d 0 v:~- == EXISTING COMPACTED "" ''" jL. SOIL FIELD VER~ I WJlJJ h\1 (SEE NOTE 2) #5 @ 12" . . ,. •
3" CLR (±) o.c. 3" CLR. ' (TYP.) (EACH WAY) (TYP.)
A.
~~ IJliii oO [g ~~ (TOP & BOT.) v
DETAIL OF REINFORCING @ WALL CORNER l (~,:~ ,lJ, II_~~~~ 0 SECTION 0 SCALE: N.T.S.
ISSUED FOR CONSTRUCTION SCALE.~l /2''-1 '-07.
DATE: 09/!9/08 CENTRAL FACILITIE~
~ SCALE: IH.S.
iOTES: 1. FOR CIVIL GENERAL NOTES SEE DWG. No. 2033 201 3Cl~CI 1101 01. "' " REVISION O(SCRIPTION OAH: '"' '" e Chevron North America CHEVRON NORTH AMERICA 2. FOR EXCAVATION ANO ENGINEER~IREMENTS SEf/' 0 JGR iSSUED fOR CONSTRUCTION 09/19/08 " '" Exploration & Production - MCBU PICEANCE FIELD DEVELOPMENT -EPS
OWG. No. zo:B-201-30 Cl 1101 01. "" c "' REVISED REf. OWGS. 12~2:yoe JGR '" CENTRAL FACILITIES 3. FOR DATUM ELEVATION SEE BEN N . . D.:'3:·20T"-30-'101-1~C~'I_l ---- OWG. SCAU:: 1/2",.,1'-0" ORAWH BY: DAW MBD-1075 LIQUID SEPARATOR FOUNDATION 4. FINISH TOP CONCRETE WALLS TRUE AND Lf.:VEL TO RECEIVE SKID.
~PROJECT OR!G. OATr: 11/12/2007 CHECKED 9Y: 00 / JCR 5. FINISH GRADE TO PROV!OE MIN. OF S 0" COVER FROM BOTTOM OF FOOTING.
ASSOCIATES PR\IJ(CT AIT: Al'f'lWVW BY: MD SHDEII O~W!NG NU).!SER I 1 ' 6. FOR SKID COORDINATES SEE FOUNDATION LOCATION PLAN OWG. 2033 201-30-CI 1102":: 15 t'"''"""('"~"·"'"'""""-"'"~""·'"c:. -·-- 2033 201 30-CI 1113 01 '""' ~. <•<~ """""·("'I;""""' '~""'"'·co."""'""""~"'"' PlOT SCALE: PLOT DATE: - -· -
! I P41 lll£0 12/26~07 07:4~ ""' \ 0~" ~o-.wM P:-.~""" ~"""'""' ?~~ '-?M •• 'Vl-n. ,,..._ .... ,
DWG. 1102-11
fl--------"~ I
11---------'1 r --,--jL ___ 1 DWG. s---1-'---,
' '
OWG. 1102-13
r--,-1-L-~ I
DWG. o r-, 1102-17 L_..J
II
HOLD UNTIL LOCATIONS AND ELEVATIONS ARE VERIFIED AFTER INSTALLATION
Chevron North America Expolorolion & Production - MCBU
PAl
ISSUED FOR CONSTRUCTION
I DEVELOPMENT
CENTRAL FACILITIES CIVIL PLOT PLAN
CODE COMPLIANCE DATA
2003 International Building Code 2003 International Mechanical Code 1
2002 National Electric Code2
2003 Fuel Gas Code 2003 ICC/ANSI A 117.1 Acceptability Standard3
2003 International Energy Conservation Code 2003 International Plumbing Code4
GENERAL INFORMATION Manufacturer ID: 4225 Dimensions: 12'-8" x 40'-0" x 12'-0" peak (11'-0" eave) Stories: 1
Occupancy Type: H25
Building Area: 520 sq-ft (enclosed space) Model Liquid Separator Building BASIC DESIGN CRITERIA
Building Type: S -Single Slope
DRAWING LIST
QTY NUMBER 66-20-H3PH-BLDG 1 OF 3 66-20-H3PH-BLDG 2 OF 3 66-20-H3PH-BLDG 3 OF 3 ENERPAN-DETAILS 8-30-SKID-SHT 1 OF 3
8-30-SKID SHT 2 OF 3 8-30-SKID-SHT 3 OF 3 CENTER OF GRAVITY 66-20-H3PH-ASSY-SHT 1 OF 3 66-20-H3PH-ASSY-SHT 2 OF 3 66-20-H3PH-ASSY-SHT 3 OF 3 2033-201-30-CI-1113-01 0706-100 0802-0101 0802-0102 0802-0103 0802-0104
DESCRIPTION LIQUID BUILDING SHEET 1 OF 3
LIQUID BUILDING SHEET 2 OF 3 LIQUID BUILDING SHEET 3 OF 3 BUILDING ATTACHMENTS DETAILS LIQUID SKID SHEET 1 OF 3
LIQUID SKID SHEET 2 OF 3 LIQUID SKID SHEET 3 OF 3 SKID LOCATION FOR CENTER OF GRAVITY LIQUID SKID ASSEMBLY SHEET 1 OF 3 LIQUID SKID ASSEMBLY SHEET 2 OF 3 LIQUID SKID ASSEMBLY SHEET 3 OF 3 LIQUID SKID FOUNDATION DRAWINGS ELECTRICAL JUNCTION BOX ELECTRICAL INSTRUMENT LOCATION PLAN ELECTRICAL LIGHTING PLAN ELECTRICAL POWER PLAN ELECTRICAL GROUNDING PLAN
Building Contains: Well Pad Separator, piping, valving and instrumentation
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 080208-CS-MBD-1 075 INSTRUMENT CONDUIT AND CABLE SCHEDULE
Roof Slope: 8.97 deg Building Size: 12'-8" x 40'-0" Peak Height: 12'-0" Eave Height: 11 '-0" Live Load of Roof: 13.6 psi Floor Live Load: 125.0 psi Floor Dead Load: 10.0 psi
Approximate Weight of Building: 5,500 LB Roof Panel Span(s):
Span 1: 12'-8" Construction Type: liB LOADS: Snow Loading:
Ground Snow Load: 65 psi Flat Roof Snow Load: 75 psi
I,= 1.1 c.= 0.9 c, = 1.1
Wind Loading: Wind Speed: 90 MPH
Importance Factor: 1.15 Exposure: "C"
Wind Topographic Effect: 1.2 per IBC 2003 (3 sec. gust) GCpi = +/- 0.18 c.= 0.9
q,: 20.2 psi
Building is "enclosed"
SEISMIC DATA
Seismic Loading: Design Base Shear: 1,000 pounds Seismic Use Group: II Importance Factor: 1.25
Site Soils: "D", S, = 0.38, S1 = 0.09,
Fa= 1.49, Fv = 2.4
Seismic Design Category: "B" Site Soil Bearing Capacity: 2000 psf (per IBC 2003) Site Soil Classification: D (per IBC 2003)
Other Loadings and Data: Concentrated Roof Load: Not Applicable Allowable Roof Panel Deflection: 1.075 inches to 1.543 inches Allowable Wall Panel Deflection: 1.075 inches to 1.543 inches
NOTES:
1) J.W. Williams will not provide any mechanical type forced ventilation.
2) J.W. Williams will not provide any AC type electrical connections, panels or devices.
3) J.W. Williams will not provide any water supply system; they will only provide a floor drain system to collect any liquids for transport on a bulk basis for appropriate disposal, by CHEVRON 4) This building is not designed for human occupancy except for periods of operation and maintenance of equipment that shall be performed by authorized CHEVRON technical personnel only. 5) This building does not have conditioned air and is exempt from energy code requirements. (20031ECC 101.2.1)
COVER PAGE
J.W. WILLIAMS INC.~,~~~ NO.
8/19/2008
a FLINT Compa Liquid Separator Building B
""·
ISO VIEW PLAN VIEW
' ' --ll£::..1
r.o. tu~N
@ELEVATION ®END VIEW ®INTERIOR BENT
0 END VIEW
T I I I I I
34'-! 1/2"
9'-o'
0--~><:!:__·•· -r--:=~~ r=:;:+==r==t=! l /~: r~ ;/ 11 I~~~ II II I \ 11 11 I \ II 11 I ~~ II II I ~ II I ;/ ~, II I 11 ~~ II
' I ;I ~~ II I 11 ~ II I ;I ~~:
(1'•118" 13'-4f'
I II I I I I
I II
I I
I II
I I
I II
I I
I II
I
I 1- II
I IUHWA~/~ I
I II
I ~-s :s;•· I
f
~~\:~ II II
I
I •·-s :st•· II
;, I I
I II
il I
I II
II I
II II
II II
II II
II JJ .J.L Lt ~I -
® ELEVATJQ!'I
l':<lr_ - ··~ I
li==~~ I~ i===l=
_£2 I:
~...!!:. /1 ' I: I; I I; I
I; I ji li!~ I~ I; I '1• I : -
;A~ I( •w. I
l~ I I: I;, .J.
@END VIEW
'.
"" '"' . """ " ..
NOTES
REfERENCED DRAIJINGS
REVISIDN
r.o. '1.~'\.!ll!s LLIAM~-.. ~~~: v~~I·:>J-1• ... J.W._W_I .. _- ·~'"'""'"""" .......... ~ - D FIELD SERVICES - TION AN FABRICA
BUIUIING HDUSU«i DETAIL ENCLil~HEVRON
"" ,. "'"' ::: -j ";:6~20-H3PH-BLDG_lli 1!'479 :\/It .$1 :. 2 DF 3 om $CAl£> N.r.s.
~··
~··
=;· !1-_-_-_-_-__ -1
i ~----
i '
LIFTING LUG SCAt.£: NONE
SEE DWG. 8-30-SKlD FOR OETNLS Ul"nNG LUG DESIGN ENGINElR CERl!FlfD
THIS OMW~G IS PROP!:IITY Of .J.W. 1'/!lLIAMS. INC, A FliNT COMPANY, AND IS NOT TO SE W~EO. COPlRO 0RI1Effi00l/CEO IN MY WAY WITHOUT THE llfliTTEN CONSENT Of J,W. WIW..IM\S, U'IC.
"'
•
SUGGESTED LIFTING DIAGRAM
NOTES NOTES'
1 ,) SUNG ARRANGEMENT SHOIJLO BE ADJUSTED lO N..JJ:1« FOR FIAT UFr. 2,) THIS DETAIL OAAWING FOR IU.US'I'Rf.TION PURPOSES ONLY, 3,) SIZING Of SPREADER BAR, CABI.ES AND OTHER UF'I!NG IAATERIALS TO BE CUSTOMER RESPONSIBIUTY
ES11WITEO SHIPPING WEIGHT: !50,020 lba.
"" "'" ""' " ..
REFERENCED DRAVINGS
R£VISIDN
"''"""'
P.o. aox 111a WAI,.~i,;R, T~XA!l <f~·n1-~~2~
FABRICATION AND FIELD SERVICES
BUILDING SUGGESTED LIFTING DETAIL
Cl£'1RllN
'"" ""' ""Ill DATE• eii09 66-20-H3PH-BLDG auT• ll If 3
E-PANEL
-i
' ~.
WALL/ROOF CROSS SECTION
Seal Typ;cat ~Weallw Proofmg Malerial)
#14 Type"A" SCII~W
FASTENING DIAGRAM
THERM0-102 WALL PANELS
TYPICAL THICKNESS (A): I 1/2" TO 6"
STANDARD LENGTHS: 0 TO 27'
CORNER DETAIL CROSS SECTION
REMOVABLE STYLE ACCESS PANEL
jAiuminum Frame Delails I
··-: . ·-··
EXTERIOR WALL TO FOUNDATION WINDOW SPECIFICATIONS
fsmcone Seal
Structural Ste;l! Skid
TYPICAL THICKNESS (A): I 1/2" TO 6"
PLEXIGLASS SKYLIGHTS
INCLUDED:
DOOR SPECIFICATIONS
INCLUDED:
FASTENING SCHEDULE WINDOWS (36" x 36" AND LARGER) - 6" SPACING.
VENTS AND TURBINES - 6" SPACING
•• ~;._'ii':.:;,IC) DOORS- 12" SPACING (BOTH SIDES)
: 1/-// @]
/
:;::/=:::::::::::=!'· @£]
I !12" POLYURETHANE PANEL SYSTEM 24 GA. SHALE GREEN (MUNSELL SOIL) EXTERIOR 26 GA. WHITE INTERIOR
12'-8" W X 40' L x II' EAVE (12' PEAK) GABLE STYLE BUILDING
J. W. WILLIAM$ fNC. :A&o8R~xr~:!s ~~.9~H-~4
- of~lUT<:<>m~ony
FABRICATION AND FIELD SERVICES
GENERAL BUilDING DETAILS EN£RPAN BUILDINGS
.. ENERPAN-DETAILS
1.) CROSS MEMSER TO t.ONG eEAA1 SHAIJ. BE FORN CIJT PRO\IIDJNG 100lC I'VU. WEB CONTACT. FLAT PlATE 6fAM GUSSETS MUST BE HAMt.tER AT PRIOR TO wao!NG TO ENSURE£ I'VLL SUPPORT AND NO GAPS.
2.) TOL£RANCES FOR SKID CONSTRUcnON ARE M3 f'OU..OWS: +1/32~ PER FOOT ON WIDTH (SKID SURI"ACE l'l.ATNESS)
w6M:6f~1f~J0.21~~~6U'f~SAG~HEN~lOR LENGTH (Sl(!O SURFACE FLATNESS)
1/8• MAXIMUM DIFFERENCE IN ANY JOINT DEPTH. 1/4! $1(10 O!l.IENSIONS. J/16" MAXIMUM fW' TOL.'ERANCE 01' CROSSMEMBER WE9 TO LONG 8001,
3.) All STRUCTURAL WEUliNG SHAll. COMPLY WITH THE I.AlEST EDITION OF AWS 01.1.
4-.) THE STRUCTUIW.. SKID WELO!NG PROCEOURES SHAll. BE: FCAW FOR All STRUCTURAL STEEL JOINTS (BCAI.t FlANGES, WEBS, GUSSETS, ETC.) GW.W FOR NON-STRUCT\IRAL (WJ. WEl.OING, ORiP UPS, ETC.)
5.) THE STRIJCT1JRAL WELOS SHALL 6E: I'VLL PENETRAllON FOR AU. FlANGe TO FLANGE JOINTS FUll STRENGTH (f1UF;T) FOR AU OTHER STRUCTlJRAL WELOS (WEB, ETC.) SfAL WElDING FOR Nff NON-LOAD BEAAING WS.OO. FILLEr FOR All Ol11ER WELOS {C'fl.HiOO'I & PIPE SUPPORTS, . GUSSETS, VESSELS)
6.) All OIMENSIQNS ARE: TO CENn!RUNES ON 8E1WS ANO COUIMNS, TOP SURFACES OF PLAT£ FLANGES OF &AlliS. eACKS OF CHM1Na5 AND ANG!.£S, UNLESS NOTED.
7 .) ~ INDICATES OJRECTION OF GRATING SPAN.
8,) ITEMS DESIGNED AS SHIP LOOSE SHAU. BE ASSEJ.!Bt.m IN THE SHOP AS COMPLEI'aY AS POSSIBLE, PRIOR TO SHIPMENT.
9.) SKID lAOOER, PlAlFORN AN!) HANDRAILS TO BE PAINi'EO PER CUM PI'IJNT SPEClF!CATlON.
10.) DEC!< PlAT£ (ITEM 39) TO BE NON-SKID OOATEO PER CUENT SPEClRCATlON.
11.) AU. OIMa-ISIONS MUST BE VERiFIED PRIOR TO FASRICATlON.
12.) UFT!NG WEIGHr • 57,560 lba. TOTAL w/ MINIMUM SHACKLE CAPACilY • 50,000 lbll. FOR EACH UFT!NG LUG.
ISO VIEW SCALE: NONE
... J.W. WILLIAMS INC. ~~.ir1~~~ ~ oA.INTC<>rnp<~n·1
FABRICATION AND FIELD SERVICES
14'.-{l' x 35'-G' SKID FUR lrGUID SEPARAT!JR ASSY. <MBD-1075)
CH£VR!JN
8-30-SKID
14'-o· SKID EOOE
lf5' IP
}§ g·-~·
'SEMI - ·- ·- - -'tf-F-+-===-=-:..:r:i -1--Fr=:.rFr==,t=-===-=== - - - ~ - . -PIPE SPT. 1
DRIP UP
o• OATIJM SKID EOCE
SUPPORTS AND STAIRS NOT SHOWN FOR ClARITY S£E SHT. 3 OF 3
1'-Q}(." T.O. MAIN STEt.
411);,· 0 REFERENCE: UNE BOTTOM OF SKID
(2) 1 1/16. AIICHOR BOLT HOLES
SE£ UFnNG LUG DETAIL OWG. 0308-0106
• !IllS IJRI\WlNG IS AAOP(lllTY 01' J.W. WILLIM1S, INC. A fLlNT COMPANY. AND IS NOT TO SE LOI\NEO, COPJ~O OR RE'PilOOIXED IN ANY WAY WITHOUT TilE WRIHEN CONSENT Of J .• WIU..!A"\S, !NC.
~@ ~ "' ~ ' ;~ 'f~ id . -!;: .. = I W 'f ;:,~!J !.,. ~~ !:::(!)! !:::~ 1rl
PLAN
ELEVATION
J ~ lo
' ~ " ~ 13'-5 1/2.
REF.
- =-·
.!:: l-.:1, ~
~3 ~~
~ ~~ K :::~ w
~ "'"' :, :,
~ ~
(2) 1 1/16" ANCHOR BOLT HOLES
I
I'®
13'-10 1/2• ~ (3) 1 1/16• O!A. ANCHOR BOLT HOLES
13'-10 1/4. DRIP UP
EDGE
s·-~· STAIR EDGE
__..- SEE ST£P DETAIL _.,- SHT, 3 OF 3
Ill;" STAIR EDGE
1 3/4. DRIP UP
EDGE 1 1/2.
£ lt!&~~~~; DH~LES
..., '"" 0 ""'
""' "' '""
" .. REVISION
~J.W. WILLIAMS INC. :MlJ.':~~·~ - ~FLINT Com~•~v 9:16.<131·21.2~
FABRICATION AND FIELD SERVICES
'"""' ..
14'-6' x 35'-{J" SKID FUR LIQUID SEPARATIR ASSY. <MBD~t075)
CHEVRJJN
I!U73 Qf(l ~ '""' ""' '""' """' $tiT• 2 IJ' 3
8-30-SKID .m SCN.Ei N.T.S.
STEP PLAN VIEW
2'-7Ji"
1'-S 1/4" 8
SECTION A-A
SECTION 8-8
~/.SS'f, REQ'O, - IS SHOWN~ 1$'(. REQ'O. - OPI'. fWOO
R OYABLE 1'00 TlWISPORTAll
3' 6" -"'•' ,.. ....
n ·~ X ~
~ ~ ## 1:. .•
# .... .. .. '"
@5 (@)
29
30
T,O. lbi!N STE£1.
... ..
PIPE SUPPORT 1 DETAIL SCAlE: 1/2"-t'-o"
2'-0"
DRAIN PLAN SECTION C-C
DRAIN TROUGH DETAIL ~ 1/2"•1'-0"
~,• (2 I<SS'f, REQ'O.)
PIPE SUPPORT 2 DETAIL SCALE: 1/2"•1'-0"
~ ,.
••• II
'• lfl "' 7 "' b
-
T.O. MAIN STm
PIPE SUPPORTS 6 &: 9 DETAIL SCAU:: 1 1/2" .. 1'-o"
'
~ ,.
~
*' ;; tft
T.O, MAIN STEEL
PIPE SUPPORTS 3 &: 7 DETAIL
,..
ri==~r i&"f HOLE
T.O. MAIN STEEL
PIPE SUPPORTS 8 DETAIL SCALE: 1 1/2°«1'-o"
ijQIE: SEE STRUClVRAL NOTtS OWC. 0308-0102.
2 '5/6" OLo\. HOI£
ELEVATION SECTION D-D
i!1 2
••• HOI.£
~ "
! I
ft z ••• Hot£
~ "
PIPE SUr.J'QBI.J DETAIL SCALE: , ... ,.-o•
;; ,.
•• f HOLE
~ 1-
I=~~- L.- Ht• HOI£
~ ~ I
"' lfl ~ {
-·· ~ "
PIPE SUPPORTS 8 DETAIL SCALE: 1 1/2" .. 1'-<l"
LIFTING LUG DETAIL SCALE: I 1/2"•1'-0"
{4 ASS(, REQ'O.)
~
'• 1 ... N
r.o. r.wN sn:a
,.
*' l! HOLE
ift
PIPE SUPPORT 5 DETAIL SCILE~ 1"•1'-o"
FABRICATION AND FIELD SERVICES
14'-Q' x 35'-Q' SKID f1R LWUID SEPARATOR ASSY. <MBD~t075>
Cl£\IR(]N
8-30-SKID
A I ' I c I 0 I ' I '
l !I '
I " "'"-"'
r::
-
~I ~ !JSf-<1'
I " I H
N, 1•oo·-~·
~ ~ ~I w
I
I
r I I I
tl. 1391'-~·
I I ' ' I I I
0 j, g ~ ~
"' ~ ""7
~~...-....-~~;;;";;::;:~;;-;;-:;-v-'-v~~--~~v-v--v-v~.TEMPORARY GENERATOR ZAN-6101 480VAC, 3 PHASE, 3 WIRE, 50 HZ, 0.8 PF
SYNCHRONIZING
BREAKER CLOSE ENABLE
480V, 3PH, 3WIRE, 2000A, MAIN BUS BRACED FOR 65KA RMS SYM.
0 I I
0 TEMPORARY GENERATOR BUS BOX ON ELECTRICAL BUILDING WALL
INCOMING LINE SECTION
120VAC CONTROL POWER
1000A =1 DT520 LSIG
i~88t~ )::~~==========~============~ 3P
3D
ETHERNEl DATA
TO PLC
I I .:ro48:':'0'-'V'=::"'S-"W:':'ITO'C:':'H::zG:":EA:l!R"-:"Z:'"Z":Z:::;-_,6'::':1 :':'0'::.0 __ f-.----- .
--_E~" -'"~=-- ~--l
APPROVED FOR CONSTRUCTION
DATE< 09/10/08
TO MCC SEE DRAWING EL-0013-01
A
2
3
4
5
6
18L
t)110AT , 150AF
6 }%KS1 ill.
8
480V-208/120V
r:~:W, 60HZ
I ) 225AT l
l.L~:.~J ELECTRICAL BUILDING LIGHTING PANEL LP-1
1BR
t)110AT • 150AF
+%KSK ill
c
480V-208/120V
f 3¢, 4W, 60HZ
y
---, I ) 225AT I If 225AF I L! ____ _J
ELECTRICAL BUILDING POWER PANEL PP-2
D E F
2000A, 480V, 10 1F 1H 1K 1M
hhhSh ---- 1.1 ---- M ---- M ---- M ----l
5 HP
ill 5
HP
p~~'J:£3 PUMP #1
H ill 0 A
5 HP
s~'if'MEb2%fL PUMP #1
8
H 0 A
20 HP
c~~~E~~~ SPARE
LOADING PUMP #1
3M 48 40
G
2BL
6 ¥si<Slffi 480V-208/120V
~ 30, 4W, 60HZ
J7"".::--, I ) 225AT I
iJ_:::~A~j HEAT TRACE
PANEL HTP-3
4F
~ ~ ~
" ~ w ~ ~ ~
0 w ~ z ~ hhhhF: ----l ---- M ---- M ---- M ---- M
t ill
h h h ) 125AT
250AF
z 0 u 8
---- 1.« ---- M ---- M
H & H & H H & & H 0 0 0 0 0 0 A A A A A A
20 3 5 1 60 20 3 5 HP HP HP HP HP HP HP HP
SPARE ~ E&:::.12.ll ~ -'2Z=JWJl -'2Z=JWJl & ~~ ~ BlA=J.lli PRODUCED FlARE SUMP AJR AIR EO FlARE SUMP
WATER SCRUBBER PUMP #1 co~J't(Ths~~l, COMPRESSOR #1 WATER SCRUBBER PUMP #2 PUMP #1 PUMP #1 PUMP #2 PUMP #2
2BR
1'\110AT I 150AF
H
20
J
2F 1'" 1'"
---- M ---- M ---- M ---- M
6 ¥sKStffi 480V-208/120V
~ 3¢, 4W, 60HZ
J-;-::--., ! ) 225AT I
L!_z!~A~J
HEAT TRACE PANEL HTP-4
4H
1 HP
~ AIR
COMPRESS0'1f2 COOLER F
5 HP
.l'll&o12Q2 TANK BOTTOM
PUMP #2
4M
t ill ) 125AT
250AF
60 HP
~& AJR
COMPRESSOR #2
ill 5
HP
~ WET OIL
PUMP #2
5BL
t) 20AT o 150AF
SPARE
H ill H & 0 0 A A
5 20 HP HP
.PJl8=J2Q.!l ~ SKIMMED OIL CONDENSATE
PUMP #2 LOADING PUMP #2
5BR
t)30AT
N 0
' ~ o 150AF 0
0
' ~ w
~ ffi 0
5 0 w ~ z ~
5 u
SPARE
K
7r---------------·----------------------· APPROVED .FOR I CONSTRUCTION
NO UY REVlSION OESCRIPnON DArt cHK ~<PP a Chevron North America CHEVRON NORTH AMERICA PICEANCE FJELD DEVELOPMENT-EPS
CENTRAL fACILITES
D.\1& 09/10/08 __
4BOV MCC ONE-LINE DIAGRAM
08/27/07 MIS Exploration & Productioo-~ 01/H/08 MIS .. 08/13/0iJ MAS 0'110. SCM.(: NONE PRAWN ilY: Pill (A!l!l)
0 Pill 1SSUf.O FOR CON$TRUC110N
1 Pill REVlSED - ISSUIW roR CONSTRUGnON
2 Pill REVlSEO PER 'IWDOR DRAWINGS
SHEET 1 OF 2 G NUilBER
09/10/08 ':Ws AMS OR!G. OAT!:: 1/2J/07 CII(Cl<fll SY:
rllll.IECT .lit: IJ'IWiUI 6'1':
PlOT SCAu:: PLOT OAtt:
P~ REVlSEO OMWlNG NUMBERS
2033-201-40-EL-0013-01
-------------------------------------~-----
3
A B c
Lh 1 25 3
3 HP HP HP
l'llA=l2>:i ~ ~ SPARE VRU SUCTION VAPOR VRU LUBE
SCRUBBER PUMP RECOVERY OIL FILL PUMP UNIT Lh COMPRESSOR
4 7H 7K 7M 80 2
~ ~ ~ t)250AT & ~
I 400AF D
" 1 1 RMS310
1 LSG
"' w ~ ~ ~
8
--'--l ~ z 1 1 ~ z ---- M ---- M 0
8 u 5
,., 0 A H
& & 0 & A
6
1/2 HP
1/2 HP
.Ellh=Jm ~ SPARE ~ GLYCOL UNIT #2 GLY~~koi~~~T #2 C RT
REBOILER FUEL GAS CONDENSATE CONDENSATE HEATER
PUMP #1 PUMP #2
0 E F
H 0 A
5 5 HP HP
SPARE GL.f6'6LW~I¥ #1 ~ GLYCOL U #1 GLYCOL PUMP #1 GLYCOL PUMP #2
SPARE SPARE
2000A, 480V, 3¢, 3W, 60Hz BUS BRACED BF BHL BHR BM
till t) ?OAT t) 30AT
Pt 150Af 150AF
---- M
- ---------- --~=:.-zs------
ill 0 A
5 HP
~5 COMP BUILDING EXHAUST FAN #1
6. 45KVA 480V-208/120V
T 3¢, 4W, 60HZ K-20 RATED
---, I ) 150AT I
~-~:':J COMPRESSOR BUILDING
PANEL /).. CBP-8ill
10 KW
2ZZ=<JlJl.1 COMPRESSOR
BUILDING GANTRY CRANE
SPARE
H 0 A
G H
H 0 A H
Lh Lh 0 A
1/2 HP
1/2 HP
""'=122Q £&=122.1 GLYCOL UNIT #1 GLwEoB~I~~AT #1 REBOILER
SPARE
CONDENSATE CONDENSATE PUMP #1 PUMP #2
FOR 65 KA RMS SYM. 90 9F
t)400AT & 400Af RM$310 LSG
t t ill
MR ----l ---- M
8
J
5 HP
SPARE SPARE o,Pc'JcLW #2 GLYCOL PUMP #1
9J 9K
5 HP
PBE-1218 GLYCOL UNIT #2 GLYCOL PUMP #2
9M
K
I I I I I I I I I ___________________________________________ J
TO TURBINE GEN. 480V MCC SEE DWG.
EL-0014-01
SPARE
5 HP
lli=.4ll.OJl
H 0 A
COMPRESSOR BUILDING EXHAUST FAN #2
SPACE SPACE
&
7
[----------------------------------------------------------------][~~!!!~!!~i:i!:~~~:!!~:!:r:~!i!!!l!il.i[i..i.i.ill'l'_li~~~~~!i"ii'i~i'!"l'i'l'':'':'m;::o',i----_!i'l~~'~~'i''l'l'l'llrl!ci&ho:!:~V:ro~a~N~orthliiAimiiien!·c:a":;'"~J[:"r:;'"'i;C:H:E\VlRO1R~IC:A~:'"~_L:l APPROVED FOR o PAl 1ssurn ~. coNsm.ue11oN OO;z7/o7 AMS Exploration & ProOOction- tvteaU PICEANCE FIELD DEVELOPMENT -EPS 1 PI<J RMSEO- ISSUW FOR CONSTRUCTION 0!/24/CBAMS CENTRAL FAC!UTES
CONSTRUCTION 2 PAl REVISED PER VENOOR DRAWiNCS 08/IJ/08 1-JJ.S owo. S(:Al(l NONE DRAWl( UY: PAl (AilS) 480V MCC ONE -LINE DIAGRAM OAT& 09(!o/oa .3 PAl RtY1SEO SREI\KER TYPES 00/10/CB 1\MS .WS ORIG. OAT!:: 1/23/07 C!ICCXEO Iff: S~~~TNO 2~ffii~f:R .<2~-----roorJ
fWJnt Ali: l.l'fW!'Ul ~:._-·-·-mr SCAU': PLOT DATE: 0 2033-201-40-EL-0013-02 3
A I B I c I D I E I F I G
5KV SWITCHGEAR
- I---------~----UN_IT __ 1----------~~~~~--~::~U~NIT~2~~~~--~~_l----~~-----UN_IT __ 3 ______ ._ ____ l_ _________ U_NIT __ <_(-SP_AA_E_)~~-- l SKY, 1200A, ~6KA!C 3¢ 3W 60HZ MAIN BUS
2
-
3
-
4
-
5
-
6
-
I I
I I
I I
S~G GCT3 L':':J 800:5A C100 (3)
+ MAIN BREAKER CB-601 1200A,36KA
a'fi6'& ,1-----<J SPARE
C100 (3)
c
1- -
GCT1(1) 100:$.(
GCT213) 800:$A
REFERENCE OWGS: POWELL£ 1026130301006 POWELL 1026130301007 PM If 2 33-201-40-EL-0010-01
7 f-------· -----·
I I
I I
l f
CLE 1.0E
PT-2(?J L 4200V IY1 I
120 ·"'-'· .r
6A
fCLE 1.: PT-w 4200V
r 12
I
I l cL.E t.OE
IPT-3(~ ""-4200V T =
'= f I I
I I I
6A
WTC eoo,SA I 0100 (3)
RMTC 800:5A 0100 (3)
+CB-602
1 120DA 36KA
I
I
I
BOCT 2000:5A
CtOO (3)
I I 2o~~iov
1~(
I RES-
SET C 144-n s9N
- - -- BEI-59N I _L --
TO GENERATOR CONTROL PANEL
'6~ ZZZ-6003 = =Sr&~MER T 4.16KV/34.5KV
35 KV SWITCHGEAR
DWG. 2033-201-40-El-0011-01
35 KV SWITCHGEAR
DWG. 2033-201-40-EL-0011-01
ISSUED FOR CONSTRUCTION
DAlE< 1012t/oo 0\IPROJECT 17""\!ASSOCIATES
~ I
RMCT 800:5A I 0100
(3)
+ CB-603 1200A 36KA
I - BOCT
2000;5A I C100 (3)
----- J
SPARE
HO llY ltt'VlSION OES<:R!PTION 0 Pol.! ISSUED FOR COI<STRUC'IlON
I H I I
DA.Tt CHK API' 10/24/06 ws JJ
~ Chevron North America ~ Expoloratlon & Production - MCBU
I
J I K
CHEVRON NORTH AMERICA PICEANCE FIELD DEVELOPMENT EPS
CENTRAL FACILITIES 5KV SWITCHGEAR ONE LINE DIAGRAM
SHEET 1
-""'"'"" "'"" l"o' 2033 201 40 EL 0015 01
-
2
-
3
-
4
-
5
-
6
-
I 8
PANEL NAME LIGHTING PANEL LP-1
c
PROM 75V0/A TRANSFORMER TX-1
I D E
LOCA"ON ELECTRICAL BUILDING
F G H
PANEL NAME POWER PANEL PP-2
I
FROM 75KVA TRANSFORMER TX-2
I K
LocAnoN ELECTRICAL BUILDING
VOLTAGE 208/120 VAGI 3 PHASE I 4 'MRE I225AMAINS MANU~~~~RER; CUTLER-HAMMER POW-R-LINE 1A £ VOLTAGE 208/120 VAG I 3 PHASE I 4 Yi'lRE I225A MAINS MANU~~~~RER; CUTLER-HAMMER POW R LINE 1 A £ CONDUIT/ CABLE # LOAD SERVED
BKR. CKT. 225AF A B C
SIZE NO. ~~T~ 1 }-t-1 8KR.
CKT. SKR. NO. SIZE
LOAD SERVED
~(7;L';;P'#1;;;-0"1R-) fCB:CU::ILO=:::IN"G_I:::N:::TE;:;R::IO::;R:'LCciGc;ffTS;::;:;:;:;::;:;::;;::':'::C:;;;-+0:20:f--;1;-j--o 0.. - -<:Jjo-r-0-30 AREA FLOODLIGHTING
CONDUIT/ CABLE #
~(0'lP'=1-=0=3=c_) f-'BO:Uc:ILO::::_IN::oGc_EXT::_:::ER::;IOO:R:..:.:AN:::D:_.::EM:::E::R::;G::;:E::NCO:Yc_::LI::GH:::T::;:S_J-"20+-;';-1-o.--...o- -<>To-~ 5 -oiio- ~~o-1-~'-t-+----------------t---~ ( lPl-OS) GAS SEPARATOR SKID f,\ :--:;-- ..-L..~ Ll..':l. so 1 -o ,_,...t- _ --<>To- a
24VDC SHUNT TRIP POLE '-g 1- -<>-t-o-1-;o 30 AREA FLOODUGHTING ( LP1-08)
~---~~~~""--~-"~C-------~-+~1711 -ojjo-- Ln..-L..o-L~~12+-+----------------+---~ 'IPT'='ff' UQUID SEPARATOR SKID '-:"::""" ..-!-. I ~ r-~ 60 13 -o 0- - -c.>1'o-~
fc----~2~4~V::DC~S~H::U~~~TR~IP~P::O::LEc_ ______ t--+~~15~ - --<>~(r~ ~ -ojo- ~..-L..o-fc:1':-t-+c~~=c~c=~c=~-------+----4
( LP1-17) PUMP SKID 60 ~ -<>..-L...o- ~ 24VDC SHUNT TRIP POLE
'r~~=o-f'2::_4c_:VO::.C~S:.;H;:UNT:::c_:_:TR;::IP-"P::.O=LEc_ ______ ~:+-:2711 1-L -ojo- 22 60 ( LP1-20) 1- I f _.1.... f--:- LACT /CONDENSATE LOADING SKID
r===+------------+':.:0+2;;;-!3 ~~~ -1-1-" ~~2::;4+-1====-=::-::::-::------+---4 VAPOR RECOVERY UNIT ~ -T- - - ~ 24VDC SHUNT lRIP POLE
( LP1-25) I :-=:-:=:::-::::;:-:::::-:---------j 60 ~ -o o- -ojo-~ 60 r: , ;.,;., 1--::.~ Gf>S FILTER SEPARATOR SKID ~------r2'-4~V~OC~S~H~U~~:.:TR~IP_cP~O~=c-------------!---~2719 -- ~_.L..o-rc30cf--fc~~=c~-=~c=:::--------------t------~
31 --oTo- [- 32 24VDC SHUNT lRIP POLE ( LPl-31 ) REBOILER/SURGE SKID No. 1 ~ j_ - f---::7 ~
60 ~ -o o-1-~ -o---r'"o-~ 6° FUEL Gf>S SKID ~ r-------~2~4~V~DC~S~H~U~:::c_~TR;::IP~P~D~LEc_ ____________ t--t~3~5 -- ro~o-~36;+--+:~~===~=~-------------+------~
~ --o;o- - - ~ 24VDC SHUNT lRIP POLE
60 ~ --o.....L_o- -o-r-o-~ 60
30 AREA FlOODLIGHTING
FLARE SCRUBBER SK!D
CONDUIT/ CABLE # LOAD SERVED
BKR. CKT. 225AF A B C 225AT \. l. ) SIZE NO. MAIN r-T-BKR.
CKT. BKR NO. SIZE
LOAD SERVED CONDUIT/ CABLE #
( PP2-01) CONTROL BUILDING PANEL CBP-5
~ -oTo- ..o--o- 2 20 BLDG. INTERIOR RECEPTACLES (EAST & SOUTH ~ 100 ~ -o10- -o--.o- 4 20 BLDG. INTERIOR RECEPTACLES (WEST) ~
~----j------------------f--J-o:S~-o_.L..o- - -T-r-1- 30 BUILDING A/C UNIT No. 1 ( PP2-06)
7 --o-r-~ - -o o-1 ~'::+-+----------------+---~ ( PP2-07) STORAGE BUILDING PANEL SBP-7 50--:- !" r g --o_.l....o- -o--r-, ~ 10
f----j------------------f--J-':~ ~f-;:-2.'_~30:.-(~B~U=ILD~I~NGCA~/::C:::U=N~IT:;;No=·~2~"'------1:(::P::P2::-::1::0::)~ A 11 -ojo- _ -o_.L..o- 12
( PPZ-ll) GENERATOR SKID ill 100 """13 -o..-J.-...r... _ -ojo- 14 :~/:,0 ~ --,;-
15 -_ _ ~_.1....~ --:-:-
16 30 24VOC RECTIFIER No. 1 ill ~
fc----+~2~4~V~DC~S~H~UN~T~TR~IP~P~O~LEo_ _________ +--+~ .. -~ ~·
~ -oTo-- >-oTo-~ 30 24VOC RECTIFIER No.2 (PP2-18) (PPZ-17 ) AIR COMPRESSOR SKID 60 ~ -o.--o- _ -o..--..o-·~;;"20::-t"--+----7-----';-----------+----j
24VOC SHUNT TRIP POLE 21 ,..-,-., 22 lr;o='=="d-:::c=-::::=::::-=o=c---------t-:::-f-::::-J -o 1 o--;::-:- 30 24VDC RECTlFIER\No. 3 fi("P"P2"-"2"3")t;:FlA;;;,R;;EO<I'TGN;;;IT;-Oc,R;;;:;;PA'7N;;_E_:cL ___________ f';;20;';-f-;20:-j3 -o_....o- - >-o_.L..o- 24 ) ( PP2-25) COMBUSTOR PANEL 20 25 ..----,.,..L -o--r-o-- 26 ~~~e:f.:.:C::::C::C.:::C.:..CC::'---------f';;;';-f~--o - r·····- 1 -=- 60 TELECOMS BUILDING ~ 20 27 -o.--..o- -o_.l....o- 28 ~=:=:e:f-------------------E20::-+-:,:::-J9 -o---..o- _ ....c-o- 30 20 SWITCHGEAR SPACE HEATER
RESTROOM BUILDING ~ -oj0- - -o '0- 32 30 GENERATOR SPACE HEATERS (!N SWITCHGEAR)
( PP2-.31) 1--:=::::-==-==-=-=---------j 60 33 --o...-l......o-1-r- -o..--..o-- 34 20 J§PARE 24VDC SHUNT TRIP POLE Ts 1- -o--.o- 36 30 CCTV CAMERAS
fc----~~~~~--------+-~ 37 -oTo- _ -o :::p... 3B 2o
~ so Ts ~--'--~ loT~~
PP2 26
(PP2 30)
PP2 32
~ ( PP2-36)
( LPl-37 ) REBOILER/SURGE SKID No. 2
24VDC SHUNT lRIP POLE
NEUTRAL BUS If 4 CfP GROUND BUS
FROM D<-1~1 \ '/' "--<
41 _ H.-lo 42
~ I 1 Q KA BUS BRACING ~ i--:2-:c4y:;;0:;c'""sH-;;U-;:~~TR=IP:-;:PO;::L-;Ec---------j ~ _ ..-L..o-< 42 30 DIESEL TRANSFER PUMP
NEUTRAL BUS If=~ CfP GROUND BUS ~ I 1 0 KA BUS BRACING ill
~~~':' 2~ ~WG ~FACTORY NElffRAL ~~ #~WG \.._ FACTORY ~ (GREEN) BONDING CUP
-------------------------
APPROVED FOR CONSTRUCTION
011 TE _ oa/u/oe
~ (GREEN) BONDING CUP
NO BY REVISION 0£SCRif'rlOH
0 PAl iSSUED FOR CONSTRUC110N
1 f'I>J Gtl<EIW. REVISION
2 f>I>J cOlM::RTt:D TO C & 0 SAGEOH SYSTEM
""<7m :~ 3 PAl l.tlOEO RESTROOM ANU CClV -"-(:;o.o) &.)<!--· -
OATI: CHK AI'P
10/17/07 MI.S 10/J.Iji)] M!S
1::1 Chevron North America llil!liii Exploration & ProciJctioo
05/20/00 M!.S AlAS 0\W, SCAU::
00/13/CS AMS M!.S ORIG. OAT£: 09/~/0~ CHECKED BY:
ll'f'ROVWBY:
Plllf IMT£:
I
MCBU CHEVRON NORTH AMERICA
PICEANCE FIELD DEVELOPMENT EPS CENTRAL FACILITIES ~
208/120 VAC PANELBQARk~lj!:OULES .3 SHEET 1 <Qf 5
-
I
~
TURBINE GENEAATOR ZAN-6102
TO TOMS CREEK LOADS
DIESEL GENERATOR ZZZ-60010
,--' ' II- I ' ' '
I' I' I' 480V SWITCHGEAR
SWITCHGEAR BUILDING ZZZ -4007
ELECTRICAL BUILDING ZZZ 4000
SMOKE DETECTOR CIRCUIT No. 1
SMOKE DETECTOR CIRCUIT No. 2
1 r 1 ANDMCC
! ! ) ) )J,·z::~1
11
~~~~---- r'--'-;c!;;::!--;_ _____ '-C7'-i__::_;_=_j
i ! z !) z ! L---------------~------."~_D_E!_E.C:'2_0_1'_T~I~ ____ j I L __ f __ _j
1
: 75 IWA TX-OZ Eo> : X;-:±-~ I : ) :
I rt I 208/120VAC : PANEL PP-2
I : ) ) : ' _j '
' '
I ' ' I ' ' I ' ' I ' '
I ' ' L __ _ ___________________________________ _j
~---.- ---------------' ' I ' : ~-~s_ti~i-1!!1~ ! lrt I i i I' : J J : I :
L.::_ __ _j : : : 208/120VAC : L----1 PANEL CBP-5 1
CONTROL BUILDING ZZZ 4001
SMOKE DETECTOR CIRCUIT No. 1
SMOKE DETECTOR CIRCUIT No. 2
' ' I ' '
I ' ' I ' ' I ' '
I '
/ '
I ' ' I ' ' I ' ' I '
i ' ' I ' '
I ' ' I ' '
I ' ' I ' ' I
'
I ' ' I '
i ' '
I '
i ' '
I ' ' I ' '
I ' ' I ' '
~~ ~I £! ~~ ~I
~~ o, ~· zl
lj ~.
~~ ~·
~~ ' '
I ' ' I ' ' I ' ' I 1 &> l GAS DETECTION TRIP 1 L------------------------------------------------r-------~ L _________________________________________ _j ' '
I ' ' I ' ' I ' ' I ' '
I ' ' I ' ' I '
Jj_ CONTINUED ON DWG. El-0060-02
~,. ~ ~~ 00 . ~~
~:!) c~ ~m CONTINUED m
M~ FROM DWR El-0050-01
;2p! n c (FUTURE) PROCESS, FIRE, &: GAS ALARM ~0 BEACONS
!Q~ ffir ~--------------------i'lffi COMBUST18LE GAS DETECTOR GO ' ' ~ffi ' '
m PUMPS SKID ' I I om ENCLOSURE
E!o ' G?5 L FUSIBLE PLUGS ' ' ' ' ffim
-------------- LOCAL CONTROL
I mr
CONDENSATE LOAOING lc~~BUSTI;l~ GAS ~~CTO~- 00
PANEL m'
0 LCP-7111
oo ' ~m ' 0.:-' {lACT) SKID 1 2oo2 VOTING ENCLOSURE 1 fiAME DETECTORS ro ro I oo L FUSIBLE PLUGS ~ ~0 ,m '
~'"' ' ~~ LACT METERING I ,o ~~~BUSTl;L~ GAS -D~ECTO~ ro ~0 BUILDING ' 0
rusiBLE -;,~UGS 0~- OIESEc-® I ' 0 ~ I I> GENERATOR AND TANKS
' ' {fUTURE) PROCESS, FIRE, & GAS AlARM BEACONS
I ~-------------------- LOCAL CONTROL ' COMBUSTIBLE GAS DETECTOR GO PANEL '
VAPOR RECOVERY : FLAME DETECTORS 2oo2 VOTING LCP-7112 I "' "' UNIT (VRU) SKID L FUSIBLE PLUGS ' ' ENCLOSURE FLCP ' ' --------------- I I FUSIBLE PLUGS ON TANKS
' ' ' ' (fUTURE) PROCESS, FIRE, & GAS ALARM BEACONS I I
())> ~-------------------- ' ' ' ' O"U COMBUSTIBLE GAS DETECTOR GO I I GAS SEPARATOR SKID 1
~ z"U ENCLOSURE 1 flAME DEfECTORS fn ' '
roll L FUS!SLE PLUGS ' '
' -IQ -------------- LOCAL CONTROL I I
~-------------------- PANEL ' LCP-7113 ' ' ,, " ::Dm COMBUSTIBLE GAS DETECTOR co
I I " UQUID SEPARATOR
: FlAME DETECTORS 2oo2 VOTING
g ~0 SKID "' "' ENCLOSURE ' ' L FUSIBLE PLUGS ~ ' '
-111 -------------- I 1i I FUSIBLE PLUGS ON z
00 PIG RECEIVERS AND SUMPS ' ~ ' ' '
I h I ZJJ 0
> ' m ' ' " ' I "' I 8> {FUTURE) PROCESS, FlRE, & GAS ALARM BEACONS ~
0 ' ~ '
~-------------------- ' I ' COMBUS118LE GAS DETECTOR GO I ~ I 0
FUEL GAS SKID : FLAME DETECTORS "' ' 2 ' ENCLOSURE ' ' L FUSIBLE PLUGS I 0 I -------------- 0 LOCAL CONTROL z
' ~ ' ~-------------------- PANEL ~ 0 '
COMBUSTIBLE GAS DETECTOR GO LCP-7114
I r
I FUEL GAS FILTER-J FlAME DETECTORS
2oo2 VOTING m
SEPARATOR SKID "' iii ENCLOSURE L FUSIBLE PLUGS ~
' ' ' 2 '
I z
I " N
FUSIBLE PLUGS ON CONTACTORS ' N
' N
' ' '
I • I 0 ~
' ' ' ' {FUTURE) PROCESS, FlRE, & GAS ALARM BEACONS I I
' ' ' ' ~-------------------- I GLYCOL REBOILER
LOCAL CONTROL COMBUSTIBLE GAS DETECTOR CO PANEL
SKID No. 1 : Fll\ME DETECTORS
LCP-7115 ' ENCLOSURE "' ' L FUSIBLE PLUGS I -------------- ' '
(FUTURE) PROCESS, FIRE, &: GAS AlARM BEACONS I ' ' I GLYCOL REBO!LER
SKID No. 2 2oo2 VOTING ' ' ENCLOSURE I FLCP
LOCAL CONTROL ' ' ~n
PANEL
I ,_;r LCP-7115
"~ FlARE SCRUBBER 2oo2 VOTING
~.s SKID '
ENCLOSURE ' Sz I ;~ ' O> ' !!"3 I n ' '
I
~ I PROCESS, ARE, & GAS ALAAM BEACONS ' '
~-------------------------- I COMBUSTIBLE GAS DETECTOR No. 1 GO ' ' COMBUSTIBLE GAS DETECTOR No. 2 LOCAL CONTROL ' ' " PANEL I COMPRESSOR I COMBUSTIBLE GAS DETECTORN No. 3
LCP-7117 BUILDING " ' ' FLAME DETECTORS "' "' "' '
' I L FUSIBLE PLUGS
------------------ ' ' FUSIBLE LOOP FUSIBLE LOOP I DISTRIBUTION PANEL CHARGE PANEL
(TYP. 7) (TYP. 7) ' ' I ' ' '
~-------------------- I I AIR COMPRESSOR COMBUSTIBLE GAS DETECTOR GO LOCAL CONTROL
SK!D ENCLOSURE -------------- PANEL ' LCP-7119 ' ' u
I 8 I
8
-
-
4
-
5
-
6
-
7
-
AREA 61 (4205-01}
c I 0 I
c
I r
D E
I G
8.8.EA-F1 (4209-01)
F
AREA-F4 (4227-01)
AREA-F5 (4236-01)
~ -11-lf'l\Y __ "1- -
I
.
I I 1 I
!i I I I
H I
G --,- r
r +
I
H
AREA-H4 (4229-01)
I
-r-
K
J
AREA-J4 (4230-01)
----H
4------i ---_i_--- j----J '-----1---f--_ji
L
~·" '
I
-
I
A
23"21"25"
R~J" ~ $ ,_ '>. .~
1 5 hj " tJ
f - I 2
-
3
-
4
-
5
-
6
I
0 I
B
r
;;:;I N
"I 0 z
I
N. 11Jo'-o"
1' WFR 36Y_
l .NQIES; 2033 20l 40 -FI 4203 01 rQII KEY PLAN. 1. SEE DRAWING EFCTOI~ cONTROLLER OH WALL AND GAS 7 FIELD INSTALL GAS D ._
' OE~fECTOR SENSOR ON CEILING.
c
1294
PIT-1294 I
I D I
-----
l.J 1-
f-
E I F I G
MATCHLmE DWG. No. _:.1 2 ~--o_·1 __ ---
I
-
~ 1-If--"-\'--, r I
·1-
r-
r r )_
h -T =
I H
MBD 104-0 GAS SEPAF<ATOR
L~IO~ERT~RAY ~J
I I I J I
N. 117'-"-0" -----
\
I~
0 I
1:::5 N
lci z
0 $: 0
w z
I::J I
I~ :>'
AIT-1040 SENSOR~ ~~__.-(r-(:=!'J:IE'J~[)J
AIT -1040 CONTROLLER ~ lF /--(--c~:::J:Cl~)
LOWER TRAY )
-----
j~rv-1 ~ , <"~ 1
UL I~ I
f- Ire ~=1 =----~~=:=----~ L i= L :=I~ T _I ,;;;; r-- MBD 1075
-,. 1-1 1
J;; j__ LIQUID SEPARAIQE ILP=_Ll....LJL~ l!flll\ - MATCHLINE DWG.No ___ 4_2_3_8--01
- - '- ~-r'N IJPPFR TRAY
lc ;p
IT- 53C I 1
I 129
------1-DCJBc ~
I 1 !00 PIT-1040<
PIT- I
TIT-_lt;_4(
r:o:· ' ' ~II'
K
A ~ 8 I c I __Q_
N'21'25"
J!l •W<UB& li ;~1 I I
_;,_
I N. 1130'-9"
- il c
I
'
-
'
- ~~
~~ 4
E:
- 8:~~
I ··' I
~ " / I
lb ~ I jl
lr J
F ~ G I H I _L I
'ER TRA'
MATCHLINE OW~. ~o. 4232 - 01 _ - -- - - -- - -...,----;l
' ' MBD-1075
.!JQJll!l._SJ'PARATOR AlT-1075 SENSOR(NOTE
I K
A B c
'
N. 996"-0"
"
_c_! __ 1
H ____ J=li GFNFRAI GRQI!NO!NG N.QJ".Eli;
1' i THE GROUND SYSTEM IS SHOWN OIAGRAMMATICALL'f, UNLESS f'IXEO BY DIMENSIONS, EXACT I j LOCATIONS TO BE DETERMINED BY THE FIELD
"
2. ALL UNDERGROUND CONNECTIONS SHALL BE MADE USING A COMPRESSION TYPE CONNECTOR '1: UNLESS SPECIFIED OTHERWISE ON DRAWINGS OR GROUNDING DETAILS, WHERE THE GROUND CABLE INSULATION MUST OC REMOVED AT THE TAPS ON SPLICES, THE CABU: SHALL BE TAPED PS SHOWN ON THE GROUNDING DETAILS.
), ALL SURFACES SHALL BE CLEANED Tl10ROUGHLY BEFORE CONNEC110NS ARE MADE TO ENSURE GOOD ELECTRICAL CONTACT.
~ ALL GROUNDING CONNECTIONS TO EQUIPMENT SHALL BE MADE WITH COMPRESSION TYPE CONNECTIONS AS SHOWN ON THE GROUNDING OETNLS UNlESS OTHERWISE NOTED.
5.1 BOLTS, NUTS AND WASHERS SHALL BE SILICON-BRONZE ALLOY FOR COPPER TO COPPER CONNECTIONS.
6.11
WHERE THE GROUND CABLE MAY BE INSTALLED ABOVE GROUND, IT SHAll 8E RUN PARALLEL IN PVC CONDUiT WITH BUILDING LINES. ROUTED ALONG THE WEBS OF COlUMNS AND BEAMS
I
AND IN CORNERS WHERE PRACTICAL FOR MAXIMUM PHYSICAL PROTECTION, UNLESS OTHERWISE DETAILED ON DRAWINGS. THE EXACT ROUnNG. ElEVATION AND BEST METHOD OF SUPPORT SHALL BE DETERMINED IN THE FIELO.
7. GROUND CABLE PENl"RATING CONCRETE OR MASONRY WALLS OR FlOORS SHALL BE "I ROUTED THRU I'" SCHEDULE 40 PVC CONDUIT SLEEVES INSTALLED IN ACCORDANCE WITH
DETAILED DRAWINGS UNLESS OTHERWISE NOTED. SEAL CONDUITS INSIDE (AFfER GROUND
1 CABLE IS INSTALLED) AND OUTSIDE WITH APPROVED NON-SKRINK DUCT SEALANT MATERIAL
B. i ~~~JJ~IR~:;TE~.Ei1tH~r~~R~"0'J~;H~~T~~~~~~c ~~~ta~n~E o~0~~fCo~~~ WEf~E i OR 8Y A #2. GROUND WIRE. REMOVABLE SECTIONS OF GRATING SHALL HAVE A i COMPRESSION n'PE CONNECTOR CONNECTED TO GRATING.
fl
1
2
3
4
5
6
0 I
"' "' " 0 z 0
"' 0
w z ::J :r: u :;;: "'
L __
c
#4/0 AWG. (BARE)_) BURIED AT EL. (-)2'-0"
I
<!> I
0
l
E
I H L1
II , I
' , I
I (, L.! L..i i······,
9 ..J-L c-1
I ~-·· !L, I
1
-·' - ~. '·I ····· , " I ,. .. __ . i. i Llr.·
F G
MATCHLINE DWG. No. 4323-01 ---- ----
#4/0 AWG, (BARE) A BURIED AT EL. (-)~ I
#4/0 AWG. (BARE) BURIED AT EL. (-)2'-0"
#2 AWG. (GREEN) BURIED AT EL. (-)2'-0" (lYP.)
#2 AWG. (GREEN)
•
H
I SPACE GROUND RODS
AT 25'-0" ON CENTER (APPROX)
--
MBD-1040 GAS SEPARATOR
MB0-1075 LIQUID SEPARATOR
J
N 1174"-0"
I
(1YP.)~ EL-4350-01 SH. \
--<p----1 #2 AWG. (GREEN)
#2 AWG. (GREEN)
0 I
n
"' "' " 0 z 0 15 w z :::; :r: 0 :;;: 2
K
?~-"--.~.~~~~~~~~-~~- ····-··-~---------"'··:~~~~~~~~~~~~~~~~~~~~~~;~~;;~~~!"~'!'~~~~"~'"';'")!''!"~"~"~"''~~~~!''!"~'!'"~"''~~t;;i~~;~ch;e;v~ro!n~~N~o~r~t~h~A~m~e~r"~,c~a~I:~~~1c~H~E[v~R~oN~Nio1RlriH~;:!.;!ElR~Ic:A~~~----t 1. sEE DRAWING 2033-201-40-EL-4300-01 c:HouNOING & LIGHTING INDEX. +PAl 1ssuEo FOR coNSTRut:::of.l IO/I0/1001.1 BH ~ Explordion & Production MCBU PICEANCC fiELD DEVELOPMENT-CPS 2. SEE DRAWING 2033-201-40-EL-4303-01 f"OR KEY PlAN. _I_ RCT ISSUEO fOR GENERAl RtvlSION 11/10/0B BH ....... CENTRAL FACILITIES
owe. SCill: 3/a" .. 1'-o· oRAWH ar: PAl GROUNDING AND LIGHTING PLAN rFi\IPROJECT _ ORIC. om, 06/13/06 Cl!tCKED 0'1: AREA ss ~~ASSOCIATES f~JECT m:: APPROvtn
61' SHOn\ ____ .::;:.::;: . ...:;.::;:"_".;;"c:'c."..:"':.:':..'.;;c::::.::....::.;... " 6.-------~~------~---~---~------~,~-------'---·- - -·· r\OlSCAt£: PtoTOATt: _ 2033-201-40-[l 4332 01 __ L1
rgtcr, P:\20J3 Chewon Pice<>nce FocWties\7.0 D•sign\40 (lectricai\Gr<>undin9 Plo_n_~~toffs\203J-201-40-Et-4JJ2-0l.dw9, 1!/10/2008 - 0~-''_'' __ m_.J.. ~--·-·-----··~-------- ---------- ___ ..J
A I B c I D I
-
2
-
3
-
4
-I
_1.$ r I '"
5 h '---'
-, (';_;';~{?\ DET.
=' SH.
6
~ --
-
I NOTES·
1. SEE DRAWING 2033 201 40-EL-4300-01 GROUNDING & LIGHTING INDEX. 2. SEE DRAWING 2033~201-40-EL 4303 01 FOR KEY PLAN.
E I F I G I
MATCHLINE DWG. No. 4332-01
tL
I I
H I
MBD-1075 LIQUID SEPARATOR
,., ......... :: .: '
I I
·--~I , ..... , ..
J
"· ,.._,.
I
I
- - -ff-'---~- ::-:=-- - -<:>----=-- - -f ---..,._ -"=Hz AWG. #4/0 AWG. (BARE)~ 11i11 IIIII "-~ IiI ~-LJ I
(GREEN) BURIED AT EL (-)2'-0" I . ·'·[HJ U!IJ \
f-- d !'3'
I i i ·u
I .j
I ---------1
MATCHLINE DWG. No. 4344-01
D I I eloo - I ~ 1
"/W/2008 - '~ :
I K
)1 I i
B L
LEGEND
~ El.(+)~-6"
01..01AB LS1
:G: EL(+)45'-6"
01-01AB L81
c~ lP1""'""""'
EL(+)45'-6'" 01..01AB
LS1
lP1"""""' ~ EL(+)~..fl"
01..01AB lS1
A Et..(+).W.(J"
30<: LS1
§] ....... HS2
(] .,_,..
® 8P-T1
0 LJ901.()1
~
®0 EL (+) o4S'-6"
01.01AB ... , 0 ® .,J •
'if'
-v NORTH-WEST C.P.F.
FLOODLIGHT. 250 WATIHPS
ElEVATION TO BOTIOM OF FIXTURE OHtl • CIRCUIT & CIRCUIT BRANCH #IN PANEL LP1 AB • PH.4.SE CONNEC110N LS1 •LIGHT SUPPORT DETAIL ON OWG. ~...c355-XXX
PENDANT MOUNT UGHT. 260 WATTHPS
ELEVATION TO lOP Of FIXtl.IRE 01-01 • CIRCUIT & CIRCUIT BRANCH# IN PANEL CBP..a AB • PHASE CONNECTlON LS1 •LIGHT SUPPORTDETAILON DWG. <W-PL.-435fi..XXX
STANCHIONMOUNTUGHT, 1SOWA1THPS
ElEVATION TO BOTTOM OF Fl.X'rlR:: 01..01•CIRCUfT&CIRCUITBRANCHIINPANalP1 AB • PHASE CONt£CTION L81 •liGHT SUPPORT DETAIL ON D'NGAO-A.-4356-XXX
WA! 1 MOI.JN!UGHT. 1fi0 WATTHPS
ELEVATION TO TOP OF FlXTURE 01-01•CIRCUIT&CIRCUITBRANCHffN PNELI.P1 AB•PW.SE~ LS1• UGHr SlWORT DETAIL ON DWG. 40-PL-43156-XXX IF NO~ IS USTED, FlXTl.R: BOllS TO EXISTJNG STRUC1'UF!AL STEEL
EMERGENCY UGHT
ElEVATION TO BOTfOM OF F'1X1'lR: 30 • CIRCUIT #IN PNEI.. UP8.,)0( C • PHASE CON'£CTlON LS1• UGHT Sl.Ff>ORT DETAIL ON DWG. 40-PL~
GAJ..TRONICS IW«lSET
HS--TS • HANDSET TAG NUMBER HS2 • HANDSET SUPPORT DETAIL ON DWG. 40-Pl:4355·XXX
GA!-TRONICS OUTDOOR 8PEAK1:R
SP..TS •SPEAKER TAG NUN8ER
GAJ..TRON!CS IMXXlR SPE*.KER
SP-T1 •SPEAKER TAG NUMSER
JUHCT10N BOX
LJB01.01 • JUNCTlON BOX TAG NUMBeR
WEA1'1-ERPR00F RECEPTAClE FOR Ct.ASS 1, OMSK>N2, 12fNN:,20AMPS
POLE. fUX)[) UGHT 2SO WATT HPS
ELEVA110N TO 901TOM OF~ 01.()1 • CIRCUIT & CIRCUIT BRANCH #IN PN£1. LP1 AB • PHASE COM£CTION l81 •UGHT SUPPORT DETAIL ON 0\YG. 40-PI...-4355-XXX
GROUNJROO
GROUND TEST WElL
IRREVERSIBLE CRIMP GROUOO GRID CONNECTION fBEt..QW GROI.IM)l
IRREVERSIBLE CRIUP GROUND IAP CClNNECT10N IBB.ON GROUNQ}
ptPE CLAMP GROUND CONNECTION..ms!,OW GR<XH>l
SERVIT POST GROUND CON'IECTION ~ GROI..N))
GROUNDING TRIAO
MAIN GR()(JM) GRID I4JD BARE COPPER 30" DEEP
PER N.E.C. 250.62F
PIPERAC!(,CAel.ETRAY SUPPORTS & MO'[QR GROUNDING ( #2 TW GREEN COPPER GROI.JN'J )
CHEVRON NORTH M1ERICA PICEANCE FIELD DEVELOPMENT-EPS liGHTING LEGEND AND SCHEMATIC
SHEET1
7
A B
i 2
3
•
•
•
7
8
c D E F
COMPRESSOR BUILDING (C.P.F.)
G
0\IPROJECT i"MASSO\=]ATES
H J K L
LEGEND
~ EL(+)-45'-e"
01..01AB LSI
B: EL{+)-4$-6"
01..01AB LSI
c-0 EL (+)45'-e"'
01.01AB LSI
~ EL(+)<45'-tr'
01.01AB LSI
Jilv EL(+)<46'.{1"
""' LS1
~ .... ,.. HS2
C] SP-11S
@ SP-T1
0 ...... ,.., ~
[&0 El..(+)-45'-6"
01.01AB lS1
0 ®
..J 9
'if'
-v
M N
FLOOOUGHT. 2MWATTI-F'S
ElEVA110N TO BOTTOM OF FIXTURE 01..01 • CIRCUIT & CIRCUIT BRANCH# IN PANEL LP1 AB • PHASE CXlM'a:Cl10N LS1 "'LIGHT SUPPORT DETAIL ON OWG. -'0-Pl.-4355-XXX.
PENDANT MOUNT LIGHT, 2!50WATT HPS
Et.EVATION TO TOP OfflXl'l.R: 01.01 • CIRCUIT & CIRCUIT BRANCH tJIN PANEl. c:ap..a A8"' PHASe CONNECnON !..!!~ -L*e!-!Te!.-~!:!:!" .... .!L~~-~-~~Y.Y.Y..
STANCI-fOIII UOUNTUGHT, 150WATTHPS
ELEVA TfON TO BOTTOM OF FlXTURE 01..()1 •ctRCUIT & CIRCUIT BRANCH 'II-IN PN£1.. LP1 AS • PHASE CClNEC110N LS1• UGHTSUPPORTDETAILONOWG~-4355-XXX
WALL MOUNT lJGHT, 150 WATT I-PS
ELEVAT10N TO TOP OF FtXTl.RE 01..01 •CIRCUIT &CIRCUIT BRANCH tiiN PANEL. LP1 AS "' PHA8E CONM:CT10N LS1 • UGHT SUPPORT DETAIL ON DWG.40-PI..-43$5-XXX IF NOSl.IPPORT IS USTEO, FIXTURE BOlTS TO EXISTING l3l'RllC'MW.. STEEL
-a.~ERGENCY liGHT
ElEVA noN TO OOTTOM OF FIXTURE 30 • ctRCUIT f. IN PNIEL U"&XX C • PHASE CONEC1lON LS1•UGHTSUPPORTDETAILONOWG.~
GAl-TRONICS ..woseT
HS-TS • HANDSET' TAG I«..MBER HS2 •HANDSET st.ProRT DETAIL ON DWG. 4Q.Pl~
GAI-lRONICS OUTDOOR SPEAKER
Sf"..TS • SPEAKER TAG NlNBER
GAl-'TRONICSIP«XXIR. SPEAKER
SP-T1 • SPEAKER TAG NI.JMBm
JUNCT10N BOX
LJB01-01•JUNCTiONBOXTAGMMBER
WEAT1£RPROOF RECePTAa..EFOR CLASS 1, DMSKJN 2. 1'2!N/JC, 20 AMPS
f:QlJi. FlOOD UGiil' 250 WATT I-PS
ELEVA110NTO BOlTOM OF F1Xl\.AE 01-01 • CIRCUIT & CIRCUIT BRANCH tiiN PANEL LP1 AS • PHASE cotKCTION 1..81•UGHTtu'PORTDETAILON DWG.40-Pl~
GROUN>ROO
"""'""' lESTwaL
IRREVERSIBlE CRIMP GROUMJ GRID c::oN'ECTION lBElOW GROUND}
IRREVERSIBlE CRIMP GROUND TAP cotN:CT10N @§,OW GROUND!
PIPE ClAMP GBQ\,!~0 CONNECTION t'BB.O'N GROUNO}
~POST GROUND c::oNiEC110N !ABOVE GROlN)}
GROUNDING lRIAD
MAIN GRCll.N) GRID lotiO BARE COPPER 30" DEEP
PER N.E..C. 250.62F
PJPERACK.CABLETRAY SI.)Pf)(')RfS & MOTOR GRC>t..M)ING
( #2 TW GREEN COPPER GROUND)
Chevron North America Exploration & Producti011 - MCBU
CHEVRON NORTH AMERICA PICEANCE FIElD DEVELOPMENT-CPS UG!fTING LEGEND AND SCHEMATIC
D\\'G. SCM£: RGY
ORIG. OAT(: 08/:l·\/08
noJrcrm:: rwr SCILC
DRAWN BY: PAl
CHtCK£0 SY:
AI'P~WI'to an
PLOT OAl<:
SHEET2
'" DRAWING N !J8ER
D 2033-201-40-PL-4301-02
2
3
•
•
•
7
•
' 0
LEGEND
~ Fl.OODUGHT, 250 WATr HPS
EL(+)<W..e"' ELEVATION TO 60TrOM OF FlXTURE ()1{11AI:'I 01-.01 • CIRCUIT & CIRCUrT BRANCH II IN PANELLP1
L$1 AS • PHASE c::oNN:CTION
LP1"""""' 1..81 "LIGHT SUPf'ORT DETAIL ON DWG.~-4355-XXX
53: pgN!lANT MOUNT UGHi'. 260 WATT 1FS
El....(+)46"-e' ELEVATION TO TOP OF FDCTtJfU: 01.01AEI 01..(H•CIRCUIT&CIRCUITBRANCHIINPANELC8P.a
LS1 AS • PHASE CONfECTION LS1 • LIGHT SUPPOIUOETAflON DWG. ~
c-w STANQiiON MOUNTUGHT. 1tiOWATrHPS
EL(+)..JS'-8" ELEVAllON TO 9CITTOM OF FDffiJRE 01-61AB 01-D'I • CIRCUIT & CIRCUIT BRANCH # IN PANEL LP1
LS1 AS • PHASE CONNECTION LS1 • UGHT SUPPORTOETAIL.ON DWGAO-PI...-4356-XXX
~ WALL MOUNTUGHT. 1150 WATT HPS
EL(+)46"-6" ELEVATION TO TOP OF FJXTURE 01-G'IAI:'I 01-o1 • CIRCU!T & CIRCIJIT BRANCH II IN PANEl LP1
1.81 AD • PHASE CONfECllON 1..81 •UGHT SUPPORT DETAIL ON DWG.40-PL~ fF NO SUPPORt' U3 USTEO, FIXTURE BOLTS TO ~_STROCTURAL_~
JTiv .........,.UGHr eL(+)<W..o" ELEVAllON TO BOTTOM OF FlXll.JlE
30.(; 30 • CIRCUIT I IN PNEl. ~ 1.81 C • PHASE CONNECTION
LS1 • UGHTSUPPORTDETAIL ON DWG. ~
~ GN-TRON!CS HANDSET
HS-16 H$-T5 • HANDSET TAG NUMBER HS2 HS2 •HANOSETStJPPORTDETAIL ON DWG. 40-f'l...~
C] GAI-TRONICS OUTDOOR SPEAKER ,.,..,. 8ft. TS • SPEAKER TAG NUMBeR
@ GAI-'TRONICS INOOOR SPEAKER
8M1 SP-T1•8PEAKERTAGNl.IMBER
0 JUNCTlON BOX
LP1""""BC 1..1101-01 WB01..01•AINC110N BOX TAG NUMBER
~ Y§Al'HERPROOF RECEPTACLE FOB Cl.AS81, OMSJON 2.1'1JNNJ.. 20AMPS
lfFD POlE. Fl..OOD UGHT 2!0WAlTHf'S
EL(+).W-8" ELEVATION TO 801TOM OF FlXll.JlE 01..01AS 01.o1 • CIRCUIT &CIRCUIT BRANCH II W PNELLP1
L81 N!> • PHASE CONfECTlON LS1 •UGHTSUPPORTDETAIL ON DWG.-40-PL-43M-XXX
0 GBQIJHQ:BQQ
® QBQI.!NO TEST WELL
.J IRRE:VERSIBL.E CRIMP GROONO GR,t.P CONNEC'IlON <BEt.QW.~l
0 IRREVERSSlE CRII,/,I" GRO!.N)TAPCONN~GR®Jml
"i!!" Pf'E Cf../WR GR<JI.A'.lO CONNECllON~GROUNQl
- 8ER\IIT POST GROUNO CONNECTION CAB0yE QBQUND..l 7 v ~NGTRWJ
MAli GROtlm GRID t.w MB!;: COPPER 30" QEEP
SOUTH-WEST C.P.F. Pl3'l N.E.C. 260..52F
!i!lQQ TANKS & VESSEl. GROlN) ti2IO BARE COPF'§'l ( UNLESS OTHERWISE NOTED )
PJF>gRAQ<.CAB!.ETRAY SUPPORTS & MOTOR GROONDIN9
( #2lW GREEN CO?P'ER GROUNO )
CHEVRON NORTH AMERICA PICEANCE FIELD DEVELOf'MENT-EPS LIGHTING lEGEND AND SCHEMATIC
SHEET3
SOUTH & SOUTH-WEST C.P.F.
LEGEND
e<&-EL {+}45'..(1"
01.01A8 lB1
:0 EL (+)45'-6"
01{11AB lB1
e-m EL("t-)45'-6"
0141AB lB1
r:B: EL(+)-45'-6"
01.o1AB lB1
EL(+).fB..()"
""' lB1
Cl
® SP-T1
0 t.J001.01
lflCJ EL (+).W.e"
01.o1AB LS1
0 ®
.J •
-
FlOOOUGHT. 250 WATI liPS
EI.EVATION TO BOTTOM OF FIXTIJRE 01.01• CRCUIT & CIRCUIT BRANCH j t-l PANELLP1 AS • PHASE CONNECTlON l81• UGHTSUPPORT OETNLON !WIG. o40-Pl-43$XXX
f"ENNANT MOUNT LIGHT 2W WAlT HPS
EI..J.:VATION TO TOP OF FDCTURI: 01.01 • CRCUIT & CIRCUIT BRANCH liN PANEL C8J>.$ AS • PHASe CONNECllON LS1• UGHT SUPPORT DETAJLON DWG. 4().Pl~
STANCHION MOUNTUGHr. 160 WATT HPS
ELEVATION TO 901'TOf.l OF FIXTURE 01..01•CRCUrT&CIRCUrT8RANCHf.lll PANEI..LP1 AS • PHASE CONNECTlON l81•UGHT SUPPORrOETAILON DWG.40-PL~
WALL MOUNT IJGHt 1M WA.TI HPS
ELEVATION TO TOP OF FOO'URE 01.01 • CRCUrr & CIRCUfT BRANCH I IN PANEL I.P1 AS • PHASe CONNEC110N L81 • LIGHT SOPPORTDETAILON DWG. 4().f'L~ IFNOSUPPORTtSUSTED, FIXTURE BOlTS TO EXISTWG STROCTUIW. STEEL
_.....,.LIGHT ELEVA noN TO BOTTOM OF FIXTURE 30 • CIRCUIT f. ~ PANEl. UPS-XX C • PHASE CONNECllON LS1•UGHT SUPPORTDETAU.ON DWG..w.A.-4356-XXX
GAI-lRONICS HANDSET
HS.T& •HANDSET TAG NUMBER HS2 • HANDSST SUPPORT DETAIL ON DWG. 40-Pl..-4355-XXX.
tw-TRONICS INDOOR Bf"EAXER
SP-T1• SPEAKER TAG NUMBER
JUNCilOH BOX
LJ901-o1• JUNCllON BOX TAG NUMBB't
~RECEPTACLE FOR ClASS 1.DMSION 2, 121NN;, 20AMF'S
PO!..S. R.OOD LJGHr250 WATT f.FS El.SVAT!ON lO 8C1TTOM OF FlXlURE 01-01 • CRCUrT & CIRCUIT 8RANCH f. IN PANEl.lP1 AS • PHASE CONNECTlON LS1 •LIGHT SUPPORT DETAU.ON DWG. 40-Pl-4355-XXX
!~CRIMP GROUND GRIP CONNainoN (8.§ ON GROUND>
!~BLE CR!W GROUND TAP CONNECTION IBElQW"GROUNOJ..
f'JPE a.AMP GRO!JNO CONNECTION f8EL.OW GROON>>
~ ¥ .,.,...,...lRW)
MM.! GROUND GRI:l fUIO BARE COPPER 30" DEEP PER N.E.C. 250BlF
SKI>. TANKS & VESSEL GROU.MQ tf2XJ BARE COPPER (UNLESS OTHER'MSE NOTeD )
P..!~Ct.BLE!RAY SUP?ORTS & MOTOR GROI.J'oiOIN<3 ( #2 TW GREEN COPPER GROUND}
CHEVRON NORTH AMERICA PICEANCE FIELD DEVELOPMENT .t':PS LIGHTING LEGEND AND SCHEM.\TIC
2
F
E
0
c
B
A
2 3
'--0 I I
<,HOMERUN r--<p
I I I I
4
JUNCTION BOX DCJB-1075
'--0 I I cr-: HOMERUN ;
4
5 6 7 8
F
SOV-10758 r--~------------------l ! ZSC-10758 I E
I I I I I I I I I I I I I I L ____________________ j
~----------~----_/ 0
(i) PEUCAN
to sa ot€NEAGY CONSULTANTS llC COV;NGTON,LA • METAIRIE,LA
5 6
NOTES:
1. N..L CABI..E SiEl.DS TO OC T,I.PEO Off 00 FIELD C€\10:: 00.
~ JUNC'llCX>I SOX TO SE ffiOOS£-HINOS f.a-242«JB-CCP, IW!H Sf. Sf. HNGES, MOJNnNG UJGS, l.ANICC¥0 NAMEPLATE, WTH 2- 2" AND 6- 1-1/2v COOOUT (')"S.UNGS IN THE BOITCM, .6.NO 8- 1-1/2" OO!'OJIT Cf!ENINGS Cf'l EA0-t SIDE . .oiU Cf'f:NING'S TO BE Slf'PUED W'IH SQ. HO. PUJGS.
3. TERMiriJIL 81..00<: PHEGIIX lf3044102 l'r?E UT4.
CHEVRON NORTH AMERICA E&P PICEANCE FIELD DEVELOPMENT- CPF
LIQUID SEPARATOR (MBD-1075)
c
B
JUNC110N BOX {DCJB-1075) A
7 8
I 2 I 3 I 4 -I 5 i 6 I 7 I 8
SYMBOL LEGEND
SYMBOL
I I 11 ;>< JUNCTION BOX
F F
1- 1-
E
-
/ -
D
1-
c
-
B
-
I 2 3 4
II
INSTRUMENT LOCATION PLAN ~' 1/2'•1'~1)"
I
(i) PEliCAN
··•••'ENERGY CONSULTANTS llC COVINGTON, LA • METAIRIE, LA
5 I
II I~ '
0 1f1) till-
IJX
6 7
'>~"''~ '~ __.-'
\...... ROXTEC ELECTRICAL PENETRATION (I @ #S008000000121, 1 @ #AWK0001201021. 2 @ #ASP0001200021,
12 @ #RM20 MODULE, 8 @ #RMJO MODULE, 6 @ #RM40 MODULE, 2 @ I/RM60 MOOULE.)
CHEVRON NORTH AMERICA E&P PICEANCE FIELD DEVELOPMENT- CPF
LIQUID SEPARATOR (MBD 1075) INSTRUMENT LOCATION PLAN
RT I
o8o2o8 I~
I 8
E
-
D
-
c
-
B
-
A
I
I (
I I i
I I f 1
J
E
D
c
B
1, CONTRACTOR SHAll. PROVIDE ATIACHEO ON F'ACE OF POVIE:R PANEL. A 1/16" 1HICK PHENOUC NAMEPLA lE, BLACK VIITH 'MiiTE LETTERS ro REAO.
3 4 5 6
(T'!!'. 4 PL)
7 8
YfB I
DOORS (TYP. 2 PL.)
---------PANEL •LP-107!Sw 120/208V
2. CONTRACTOR SHAll. PROVIDE A PANEL DIRECTORY CARD. 3, PER NEC ART-110 MAINTAIN DISTANCE OF 2'-6" FRQJ FRONT OF PANEL TO NEAREST OBSTRUCliON. 4. SEAL-OFFS SHALL BE PLACED IN AU. RECEPTAQ.E CONDUITS
WITHIN 18~ Ot RECEPTAQ.E UUNCl10N BOX. 5, MOUNT RECEPTAQ..E 1'-G• FROM FINisH FLOOR TO CENTERUNE OF RECEPTACLE. 6, SEE DRAWING f 0802-0102 FOR BUBBlED ITEMS MATERIAL UST.
ol @)/
~= ~
'@)
~ --..:::::
( !'--- ./1' . -
t fO 3 1/2"
1:t .., " ..
RECEPTACLE NEMA~ OONAGURATION ~~
OJl' RECEPTACLE
5-20R
••
EXPI OS!ON PROOF RECEPIAC! E DETAIL ® N.T.S
2
LP-1075-4,6
POWER PLAN N.T.S
PANEL "LP-1075" SEE NOTE #3
12" CABLE TRAY FRC!.4 El.£C1RICAL PENETRATION TO
DCJS-1075 AND lP-1075
100
I 1'
20
CROJSE-HINOS fENRC21201. THRU. FEED ASSEMBLY ¥11TH SPRING DOOR OPEN RECS'TACl£ CATALYTIC HUB SIZE 3/4", 125V, 20 ANPS, ClASS I, OIV. HEATER A l.t2, GROUPS B.C.O. ARK-GARD 2. FACTMY SEAL (rn>. 4-PlACES).
CATAlYl\C HEATER B
UGiTS
EMERGENCY UGHTS
SPARE
SPACES
j_ !lllla
ROXTEC ELECTRICAL PENETRATION
N SEE DWG. #08D2-D1 D1
t-FOR PART NUMBERS
DO NOT GROUND PANEL NEUTRAL.
20
\.---SPARE 20r---GFCI
~~--.<' / RECEPTAClE(S) A 20r---GF'CI
f-ll.---./ / RECEPTAClE(S) 6 20r---GFCI
j-A---f/ HEAT TRACE A 20r---GFCl
f-l.ll---.// HEAT TRACE 8 20r---GFCI
'----SPARE
'---SPARE
SPACES
MElHOO OF TERMINAllON BY OTHERS. PANEL AIC RAllNG IS 5,000A 0 208V AC.
~N ,,,,,,ENERGY CONSUlTANTS llC CO\"'NOTON. LA • METAIRE,t.A
5 6 7
CHEVRON NORlli AMERICA E&P PICEANCE FIELD DEVELOPMENT- CPF
UQUID SEPARATOR (MB0-1075) POV£R PLAN
F
E
D
c
B
A
3 4
E
INSULATOR 801}1 SIDES
D
C> C>
C>
C> GROUND BAR (COPPER)
C> BOITOM Of BAR 1 '-6" FROM FLOOR
' C>
C> C>
C> ' c C>
SEE NOTE #1
GROUND BAR ELEVATION N.T.S
B
1.) SKID 'vENDOR TO DRILL & TAP 2 HCU:S ON OPPOSrTE CORNERS Of THE SKID. DRILL AND TAP 1/2-13. TO BE USED BY OTiiERS FOR SKID GROUNDINGS.
A 2.) JJNCllON BOXES AND HEATERS ARE MOONTEO TO H/2" x H/2" K 1/4" ANGI.£ ON HORIZONTAL PLANE. l;fRTICAL ANGLE IS ATTACHED TO HOO!ZONTAL ANGLES (3) AND GROUND BAR IS BOll!D TO ANGIJ:.
3.) CATALYTIC HEATER - #12 THHN w/ Jjl( RMC.
2 3 4
LP-1075-5
5 6
1 1/2"X1 1/2"X 1/4" -( SEE NOTE #2
CATALYTI HEATER
OCJB-1075
1 1/2"X1 1/2"X 1/4" '<. SEE NOTE #2
(i) PELICAN
·e••··eNEAGY CONSULTANTS U.C COVINGTON. LA • MET A!RIE, LA
5 6
7 8
F
E
SEE NOTE #1
D
c
B
CHEVRON NORTH AMERICA E&P PICEANCE FIELD DEVELOPMENT- CPF
LIQUID SEPARATOR (MBD-1075)
~~ GROUNDING PLAN A
7 8
Chevron Piceance Basin Project Liquid Separator Skid- MBD-1075 Instrument Conduit and Cable Schedule Document #080208-CS-M B D-1 075 Revision D
Cable Number Instrument Cable, Type 300V, CU, Stranded Conduit Size & Type From To Comments
LIT-1075A 1 PR. #16 SHLD. 15" RMC OCJB-1075 LIT-1075A --LIT-1 075B 1 PR. #16 SHLO. 1.5" RMC OCJB-1075 LIT-1075B LIT-1075C 1 PR. #16 SHLO. 1.5" RMC OCJB-1075 LIT-1075C ·-LIT-10750 1 PR. #16 SHLO. 1.5" RMC OCJB-1075 LIT-10750 ·-·-FIT-1075A 1 TRI. #16 SHLO. 1.5" RMC OCJB-1075 FIT-1075A ---·----PIT-1075A 1 PR. #16 SHLD. 1.5" RMC OCJB-1075 PIT-1075A ------PCV-1075B 1 PR. #16 SHLO. 1:5"RMC OCJB-1075 PCV-1075B FIT-1075B 1 TRI. #16 SHLO. 1.5" RMC OCJB-1075 FIT-1075B PIT-1075B 1 PR. #16 SHLO. 1.5" RMC OCJB-1075 PIT-1075B --LCV-1075A 1 PR.. #16 SHLO. 1.5" RMC OCJB-1075 LCV-1075A TIT-1075 1 PR. #16 SHLO. 1.5" RMC OCJB-1075 TIT-1075
FIT-1075C 1 TRI. #16 SHLO. 1.5" RMC OCJB-1075 FIT-1075C ---PCV-1075A 1 PR. #16 SHLO. .1.5" RMC OCJB-1075 PCV-1075A LCV-1075B 1 PR. #16 SHLD. 1.5" RMC OCJB-1075 LCV-1075B SOV-1 075B 4 PR. #16 SHLO. 1.5" RMC OCJB-1075 ZSC-1075B
OCJB-1075 ZS0-1075B OCJB-1075 SV-1075B --OCJB-1075 HS-1075B
1--
-------
C:\Oocuments and Settings\matthewcosta\Oesktop\RT\Transmittals\080208-T0027\080208-CS-MBD-1 075 Rev D.xls
top related