input & output processor - accessnsite.com · the input processor (ip) provides the capability...
Post on 25-Jun-2020
18 Views
Preview:
TRANSCRIPT
The Input Processor (IP) provides the capability of supporting 16 general purpose inputs such as motion detectors, door contacts, or panic alarms. It also has two general purpose outputs. The Output Processor (OP) provides the capability of supporting 16 general purpose outputs. The outputs can be used for a variety of purposes such as lighting, heating/cooling, and door and elevator control.
Inputs can be individually set to be normally-open or normally- closed, can be configured as either supervised or unsupervised, and can be masked. Each input can also be set for sensitivity ranges, timing parameters, and end-of-line resistance values. Outputs are Form-C (NO/NC) relays and can be configured for fail-safe or fail-secure operation. Relays support “On”, “Off”,
“Pulse” and “Repeat Pulse” commands. Relay operation and alarm masking may be initiated by operator action, time schedule, or triggered by an event. The IP and OP use a high speed, two wire, multi-drop RS-485 interface to communicate with the controller (ADC, IDC, or IDC-1).
Events generated by the IP or OP can be used to trigger actions locally or on other sub-controllers attached to the same controller. Status change, command, and configuration information is ex- changed with the controller. The controller is managed by a host computer using industry leading AccessNsite® software, but runs independently when not communicating with the host.
Quintron Systems, Inc.Security Systems Division
2105 S. Blosser RoadSanta Maria, California 93458
Phone: (805) 928–4343Fax: (805) 928–9914
Web: www.quintron.comEmail: sales@quintron.com
Control up to 16 points with one board
• Most widely accepted access control hardware due to its reliability and open architecture• AES 128 bit data encryption
• Compatible across Quintron’s family of Distributed Controllers• Dedicated tamper and power
fault monitoring
• 12v to 24v DC operation• Configurable input/output parameters• Diagnostic LEDs• Field upgradable firmware
• UL listed 294/1076 • 1-year limited warranty
Input & Output Processor
powered by
®
Features
Output Processor(16 outputs)Input Processor
(16 inputs)
Quintron Systems, Inc.Security Systems Division
2105 S. Blosser RoadSanta Maria, California 93458
Phone: (805) 928–4343Fax: (805) 928–9914
Web: www.quintron.comEmail: sales@quintron.com
Primary Power• 12 to 24Vdc +/- 10%, 350 mA max
Relays• 2 Relays: Form-C, 5A @ 28 Vdc
Inputs• 16 supervised • 2 dedicated: Tamper & power fault
Primary Power• 12 to 24Vdc +/- 10%, 1100
mA max
Relays• 16 Relays: Form-C, 5A @ 28 Vdc
Inputs• 2 dedicated: Tamper &
power fault
Dimensions• 6.0” W x 8.0” L x 1.0” H
Temperature• 0°C to +70°C operating • -55°C to +85°C storage
Humidity• 0 to 95% RHNC
Communication• RS-485, 2-wire, 4000’
Certifications• UL294, UL1076 • CE • RoHS
QuintronCustom Enclosures
* For a list of preconfigured enclosures, see Quintron’s Enclosures brochure.
IP Specifications OP Specifications Common Specifications
ERI
MUX8
Controller
Network
OutputProcessor
InputProcessor
SRI
DRI
powered by
®
KRIInput Processor
STATU
S LE
Ds
J3
SG
R-
R+
TR-
TR+
AC
DC
AC
GN
D IN1IN2IN3IN4IN5IN6IN7IN8
2W 4W
RS 485
GN
D
CT
BA
OFF O
N
8 7 6 5 4 3 2 1
J1
RS
-485
GN
D
IN11IN12IN13IN14IN15IN16NO C NC NO C NC
OU
T1
OU
T2
ABK1
K2 IN9IN10
12345678
910111213141516
J2
TER
M
CT
BA 5.50 [139.70]
6.00 [152.40]
2.00 [50.80] 2.00 [50.80]3.00 [76.20]
8.00 [203.20]
Output Processor
J3
SG
R-
R+
TR-
TR+
AC
DC
AC
GN
D
2W 4W
RS 485
OFF O
N
8 7 6 5 4 3 2 1
J1
RS
-485
ABCT
BA
J2
TER
M
STATU
S LE
Ds
1 2 3 4 5 6 7 8 9 10 11121314 15 16N
CCC
OM
NC
CCO
M
NC
CCO
M
NC
CCO
M
NC
CCO
M
NC
CCO
M
NC
CCO
M
NC
CCO
M
NCC
CO
M
NCC
CO
MNCC
CO
M
NCC
CO
MNCC
CO
M
NCC
CO
MNCC
CO
M
NCC
CO
MGN
D
BA
GN
D
CT
5.50 [139.70]6.00 [152.40]
2.00 [50.80] 2.00 [50.80]3.00 [76.20]
8.00 [203.20]
QuintronCustom Enclosures
top related