lift table diy plans
Post on 16-Jul-2016
266 Views
Preview:
DESCRIPTION
TRANSCRIPT
-
DIY WORKSHOP TABLE LIFT
-
DIY WORKSHOP TABLE LIFT
-
DIY WORKSHOP TABLE LIFT
-
DIY WORKSHOP TABLE LIFT
-
24.000
32.000 2.500
14.500
21.000
16.000
12.000 16.000
1.500 Angle Steel
4.000 4.000
1.500
2.500
2.500
Weld in 2.5" x 12" x 1/8" Flat metal (Both Sides)
Weld in 2.5" x 21" x 1/8" Flat metal
1.500 1.500
Both Upper & Lower Framesare the same dimensions and
Welded together using:
1 1/2" x 1 1/2" x 1/8" Angle Steel
-
7.000 7.000
6.000
6.000
6.000
6.000
6.500 .750
9.000 9.000
5.000 5.000
1.000
1.000
.250 x 16
Both Upper & Lower Framesare the same dimensions and
Welded together using:
1 1/2" x 1 1/2" x 1/8" Angle Steel( SEE - LOWER FRAME for Fabrication Dimensions )
Holes have same dimensions as Wood Table Top
-
1.000 1.500
17.750
29.500 29.500
19.750
.500
14.250
14.250
.500
28.500
.375 x 3 Holes
19.750 1.000
1.000
LOWER HINGE LEGS & UPPER WHEEL LEGSare the same dimensions
and welded together Using :
1" x 1" x 0.120" Square Steel Tubing
-
19.875
1.500 1.000
29.500
21.875
21.875 1.000
1.000
.500
14.250
14.250
.500
28.500
.375 x 3 Holes
UPPER HINGE LEGS & LOWER WHEEL LEGSare the same dimensions
and welded together Using :
1" x 1" x 0.120" Square Steel Tubing
-
.188
.250
17.250
1.250
3.000 45.00
4.000
2.500
.188
1.000
17.625 is the important dimension
Weld on a 5/8" Nut
6.250
1.000
.500
.500
.375 x 2 Holes
You can use 5/8" (UNC) Thread .
or 5/8" ACME Thread(ACME Thread is Much More Expensive)
Both Thread Support Bracesare the same dimenstions
and welded together using :
1" x 1" x 0.120" Square Steel Tubing
Side Tabs : 1" x 2 1/2" x 3/16" Flat steel
( You can modify this part shape as long as it's width is 17.625" )
Weld Nut on one and a Washer on the other
-
I cut my wheels out of Delrin on the Latheand drilled a 0.375" hole in each wheel
.500
1.375
1.375 O.D. .375 Hole
8 count -- 2.75" Long
4 count -- 2.25" Long
( Brass Washers next to Wheels )
I am sure you can figure out the Nuts & Washers
You can Use Plastic, Delrin, or Bearings for the Wheels
The important dimension is the wheel O.D. needs to be 1.375"
ALL BOLTS ARE 3/8" (UNC)
ALL Flathead Machine Screws are 1/4" (UNC)
16 count -- 1.125" Long
4 count -- 3.00" Long
Sheet1Drawing View4
DIY WORKSHOP LIFT TABLE 1.PDFSheet1Drawing View2
DIY WORKSHOP LIFT TABLE 2.PDFSheet1Drawing View1
DIY WORKSHOP LIFT TABLE 3.PDFSheet1Drawing View2
Lower Frame Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4
Upper Frame Dimensions.PDFSheet1Drawing View1Drawing View2
Lower Hinge Legs Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4
Upper Hinge Legs Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4
Threaded Supports Dimensions.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4
Wheels and Fasteners.PDFSheet1Drawing View1Drawing View2Drawing View3Drawing View4Drawing View5Drawing View6
top related