machine safe guarding training

1

Machine Guarding

Julian Kalac, P.EngJune 11, 2013

2

Scenario• Printing press• 42 year old operator with 20 years exp.• Pinch point – 150psi• Distance from pinch point to safety stop

– 8 feet• No guards in place • Operator goes to remove a paper jam……..

3

4

5

6

7

8

9

Result• Hospitalized for 1 week• Rehabilitation for 4-6 months• Severed tendons & nerves• Laceration to bone• Missing nerves & tendons• Loss of sensation• Loss of range or motion• Finger tips permanently bent

*These are onlyThe physical problems

10

Any machine part, function, or process which may cause

injury must be safeguarded

Rule to Remember

11

12

New Guardsfor Printing Press

13

14

15

16

Types of Hazardous Mechanical Motions

and Actions• Rotating (including in-running nip points)• Reciprocating• Transverse

• Cutting• Punching• Pinching• Shearing• Bending

17

Rotating Motion• Common rotating mechanisms

– Collars– Couplings– Cams– Clutches– Flywheels– Shaft ends– Spindles– Horizontal/vertical shafting

Dangerous moving parts in these basic areas require safeguarding:

1. Point of operation

2. In running nip points

3. Pinch points

4. Power transmission

5. Other moving parts

Where Dangerous Mechanical Hazards Occur

19

Types of Machine Guards• Guards

– Fixed– Interlocked– Adjustable– Self-adjusting

• Devices– Presence sensing

• Photoelectrical (optical)• Radio frequency (capacitance)• Electromechanical

Machine Guards• Machines guards are there to protect from

exposed hazards• Guarding MUST never be removed unless

under supervision and locked out• If a Guard is missing notify your supervisor

immediately • Never bi-pass the guarding!

20

21

Types of Machine Guards• Devices (cont’d)

– Pullback– Restraint– Safety controls

• Safety trip control– Pressure-sensitive body bar– Safety trip rod– Safety tripwire cable

• Two-hand control• Two-hand trip

– Gates• Interlocked• Other

22

Fixed GuardProvides a barrier - a permanent part of the machine, preferable to all other types of guards.

Parts rotating in opposite direction

In-running nip point hazards

Rotating and tangentially moving parts

Rotating Parts

Point of contact between a chain and a sprocket

Examples of 3 Types of Motion

Rotating and fixed parts

Transverse motion

Rotating and tangential motion

Grinder Safety

25

Grinder Safety (cont)

26

Cutting Saws

27

Point of contact Blade not guarded

Max Gap Allowable gaps Grinder

Guarded vs Ungarded Saw

29

PINCH POINTS

LAMINATOR GUARDING

Interlocked Guarding

Mesh Guarding

32

Adjustable GuardProvides a barrier which may be adjusted to facilitate a variety of production operations.

Bandsaw blade adjustable guard

33

Self-Adjusting Guard

Provides a barrier which moves according to the size of the stock entering the danger area.

Circular table saw self-adjusting guard

34

Two-Hand Control

.

• Requires constant, concurrent pressure to activate the machine

• The operator’s hands are required to be at a safe location (on control buttons) and at a safe distance from the danger area while the machine completes its closing cycle

35

Gate• Movable barrier device which protects the operator at the

point of operation before the machine cycle can be started

• If the gate does not fully close, machine will not function

Gate Open Gate Closed

36

Safeguarding by Location/Distance

• Locate the machine or its dangerous moving parts so that they are not accessible or do not present a hazard to a worker during normal operation

• Maintain a safe distance from the danger area

Example #1 Slitter guarding using guards

Front view of guard

Example #1 SLITTER GUARDING USING MECHANICAL GUARDS

Example #2 Slitter guarding using light curtains

Example #2 Slitter guarding using light curtains

42

Not Guarded

43

Guarded

44

Machine Safety Responsibilities

• Management– ensure all machinery is properly guarded

• Supervisors– train employees on specific guard rules in their areas– ensure machine guards remain in place and are functional– immediately correct machine guard deficiencies

• Employees– do not remove guards unless machine is locked and tagged– report machine guard problems to supervisors immediately– do not operate equipment unless guards are in place

45

Training Questions

• Why must machines be guarded?• What are the machine hazards ?• When can you remove a guard?• What to do if a guard is missing or

damaged?

46

Any machine part, function, or process which may cause

injury must be safeguarded

Rule to Remember

47

QUESTIONS???