manual instalacion cinta
Post on 03-Jun-2018
224 Views
Preview:
TRANSCRIPT
-
8/13/2019 Manual Instalacion Cinta
1/36
I n s t a l l a t i o na n d
M a i n t e n a n c e
M a n u a lwith Safety Information
and Parts ListRECOMMENDED SPARE PARTS HIGHLIGHTED IN GRAY
IMPORTANT!
DO NOT DESTROY
Model TR
HYTROL CONVEYOR CO., INC. COPYRIGHT 2005HYTROL CONVEYOR CO., INC.
Jonesboro, Arkansas
Effective June 2005(Supercedes November 2003)
Bulletin # 557
IMPORTANTE!NO DESTRUIR
M a n u a lde Instalaciny
M a n t e n i m i e n t ocon Informacin sobre Seguridad
y Lista de PartesPARTES DE REPUESTO RECOMENDADAS SE RESALTAN EN GRIS
-
8/13/2019 Manual Instalacion Cinta
2/36
2
Table of Contents Tabla de ContenidoWarning Signs . . . . . . . . . . . . . . . . . . . . .3
INTRODUCTIONReceiving and Uncrating . . . . . . . . . . . . .4
INSTALLATION
Installation Safety Precautions . . . . . . . .4Support Installation . . . . . . . . . . . . . . . . .5Ceiling Hanger Installation . . . . . . . . . . .6Conveyor Set-Up . . . . . . . . . . . . . . . . . . .7Belt Installation . . . . . . . . . . . . . . . . . . . .8Electrical Equipment . . . . . . . . . . . . . . .10
OPERATIONOperation Safety Precautions . . . . . . . .12Conveyor Start-Up . . . . . . . . . . . . . . . .12
MAINTENANCE
Maintenance Safety Precautions . . . . .13Lubrication . . . . . . . . . . . . . . . . . . . . . . .13Belt Tracking . . . . . . . . . . . . . . . . . . . . .14Drive Chain Alignment and Tension . . .17Trouble Shooting . . . . . . . . . . . . . . . . . .18Maintenance Checklist . . . . . . . . . . . . .20How To Order Replacement Parts . . . .22
REPLACEMENT PARTSModel TR Parts Drawing & List4 End Drive . . . . . . . . . . . . . . . . . . . . .248 End Drive . . . . . . . . . . . . . . . . . . . . .264 & 8 Center Drive . . . . . . . . . . . . . . .284 Center Drive Assembly . . . . . . . . . . .308 Center Drive Assembly . . . . . . . . . . .31Power Feeder . . . . . . . . . . . . . . . . . . . .32Underside Take-Up . . . . . . . . . . . . . . . .34
Seales de Advertencia . . . . . . . . . . . . .3
INTRODUCCIONRecepcin y Desembalaje . . . . . . . . . . .4
INSTALACION
Seguridad en la Instalacin . . . . . . . . . . .4Instalacin de los Soportes . . . . . . . . . . .5Instalacin de los Soportes de Techo . . .6Montaje . . . . . . . . . . . . . . . . . . . . . . . . . .7Instalacin de la Banda . . . . . . . . . . . . . .8Equipo Elctrico . . . . . . . . . . . . . . . . . .10
OPERACIONSeguridad en la Operacin . . . . . . . . . .12Arranque del Transportador . . . . . . . . .12
MANTENIMIENTO
Seguridad en el Mantenimiento . . . . . .13Lubricacin . . . . . . . . . . . . . . . . . . . . . .13Alineacin de la Banda . . . . . . . . . . . . .14Alineacin y Tensin de la Cadena . . .17Resolviendo Problemas . . . . . . . . . . . .19Mantenimiento Preventivo . . . . . . . . . . .21Como Ordenar Partes de Repuesto . . .23
PARTES DE REPUESTODibujos y Listas de Partes del Mo. TRUnidad Motriz de Extremo de 4 . . . . . .24Unidad Motriz de Extremo de 8 . . . . . .26Unidad Motriz Central de 4 y 8 . . . . . .28Ensamble de la Unidad Motriz
Central de 4 . . . . . . . . . . . . . . . . . . .30Ensamble de la Unidad Motriz
Central de 8 . . . . . . . . . . . . . . . . . . .31Alimentador Motriz Estndar . . . . . . . . .32Ensamble del Tensor Inferior . . . . . . . .34
-
8/13/2019 Manual Instalacion Cinta
3/36
-
8/13/2019 Manual Instalacion Cinta
4/36
4
INTRODUCTION
This manual provides guidelines and procedures for
installing, operating, and maintaining your conveyor. Acomplete parts list is provided with recommended spare
parts highlighted in gray. Important safety information isalso provided throughout the manual. For safety to person-
nel and for proper operation of your conveyor, it is recom-
mended that you read and follow the instructions providedin this manual.
Check the number of items received against the bill oflading.
Examine condition of equipment to determine if anydamage occurred during shipment.
Move all crates to area of installation.
Remove crating and check for optional equipment thatmay be fastened to the conveyor. Make sure theseparts (or any foreign pieces) are removed.
NOTE: If damage has occurred or freight is missing, see
the Important Notice attached to the crate.
INSTALLATION
1. . .
2. . .
3. . .
4. . .
I N T R O D U C C I O N
Este manual provee las pautas y los procedimientos para
instalar, operar, y mantener su transportador. Se propor -ciona una lista completa de repuestos, de los cuales, los
recomendados, estarn resaltados en gris. Tambin se pro -porciona informacin importante de seguridad a lo largo de
este manual. Para seguridad del personal y para un fun -
cionamiento apropiado del transportador, se recomiendaque lea y siga las instrucciones proporcionadas en estemanual.
NOTA: Si algn dao ha ocurrido o falta cargamento,vea las Notas Importantes adheridas al embalaje.
Receiving and Uncrating Recepcin y DesembalajeVerifique el nmero de partes recibidas con elconocimiento del embarque.
Examine las condiciones del equipo para determinar sialgn dao ha ocurrido durante la transportacin.
Mueva todo el equipo hacia el rea de instalacin.
Remueva todos los empaques y verifique si hay partesopcionales que deben estar atadas al equipo.Asegrese de que estas partes (o cualquier otras
partes externas) sean removidas.
1. . .
2. . .
3. . .
4. . .
GUARDS AND GUARDING
Interfacing of Equipment. When two or more pieces ofequipment are interfaced, special attention shall be given to
the interfaced area to insure the presence of adequateguarding and safety devices.
Guarding Exceptions. Wherever conditions prevail thatwould require guarding under these standards, but such
guarding would render the conveyor unusable, prominentwarning means shall be provided in the area or on the
equipment in lieu of guarding.Guarded by Location or Position. Where necessary for
the protection of employees from hazards, all exposed mov-
ing machinery parts that present a hazard to employees at
their work station shall be mechanically or electrically guard-
ed, or guarded by location or position.
When a conveyor passes over a walkway, roadway, or work
station, it is considered guarded solely by location or posi-
tion if all moving parts are at least 8 ft. (2.44 m) above the
floor or walking surface or are otherwise located so that the
Installation SafetyPrecautions for Conveyorsand Related Equipment
GUARDAS Y PROTECCIONESUnin del Equipo. Cuando dos o ms piezas del equipovan unidas, debe ponerse especial atencin al rea de
unin para asegurar que las guardas adecuadas y los dis -positivos de seguridad estn presentes.
Excepciones de Proteccin. Dondequiera que lasguardas sean necesarias, pero que la colocacin de las
mismas inhabilite el uso del transportador, se propor -cionarn seales de advertencia visibles en el rea o en el
equipo en vez de las guardas.
Proteccin dada por Posicin o Ubicacin. Cuando seanecesaria la proteccin de los empleados contra posibles
riesgos, todas las partes del equipo que estn expuestas y
en movimiento, y que puedan presentar un peligro para
ellos en sus puestos de trabajo, sern protegidas mecnica
o elctricamente, o protegidas por su posicin o ubicacin.
Cuando el transportador est instalado sobre pasillos,
corredores o puestos de trabajo, se considera protegido
nicamente por localizacin o posicin si todas las partes
Medidas de Seguridadal Instalar Transportadoresy Equipos Relacionados
INSTALACION
-
8/13/2019 Manual Instalacion Cinta
5/36
Determine primary direction of product flow. Figure 5A
indicates the preferred flow as related to the drive.Refer to Match-Mark numbers on ends of conveyor
sections. (Figure 5A).Attach supports to both ends of drive section and to
one end of intermediate or tail sections (Figure 5A).
Hand tighten bolts only at this time.Adjust elevation to required height.
Determine la direccin primaria del flujo del producto.
La figura 5A indica el flujo preferido en relacin con launidad motriz.
Refirase a las Etiquetas de Secuencia de Armadosituadas al final de las secciones del transportador.
(Figura 5A).
Fije los soportes en ambos extremos de la seccinmotriz y a un extremo de la seccin intermedia o final(Figura 5A). Apriete los tornillos manualmente.
Ajuste la elevacin a la altura requerida.
Support Installation Instalacin de los Soportes1. . .
2. . .
3. . .
4. . .
1. . .
2. . .
3. . .
4. . .
employee cannot inadvertently come in contact with haz-
ardous moving parts.Although overhead conveyors may be guarded by location,
spill guard, pan guards, or equivalent shall be provided if theproduct may fall off the conveyor for any reason and if per-
sonnel would be endangered.
HEADROOMWhen conveyors are installed above exit passageways,
aisles, or corridors, there shall be provided a minimumclearance of 6 ft. 8 in. (2.032 m) measured vertically from
the floor or walking surface to the lowest part of the con-veyor or guards.
Where system function will be impaired by providing theminimum clearance of 6 ft. 8 in. (2.032 m) through an emer-
gency exit, alternate passageways shall be provided.It is permissible to allow passage under conveyors with less
than 6 ft. 8 in. (2.032 m) clearance from the floor for otherthan emergency exits if a suitable warning indicates low
headroom.
en movimiento estn mnimo a 8 pies (2.44m) de altura del
piso, o si est localizado de tal manera que el empleado nopueda entrar en contacto inadvertidamente con dichas
partes.A pesar de que los transportadores ereos pueden estar
protegidos por su localizacin, guardas laterales e
inferiores deben ser proporcionadas para evitar que el producto se caiga del transportador y as mantener al personal fuera de peligro.
UBICACION SUPERIORCuando los transportadores son instalados sobre pasillos ocorredores de salida, debe dejarse un espacio libre de
mnimo 6 pies 8 pulgadas (2,032m) de extensin, medidoverticalmente desde el piso o rea de trnsito hasta la parte
ms baja del transportador o de las guardas.Si se proporcionan seales de advertencia adequadas indi
cando baja altura; es posible dejar espacio libre con menosde 6 pies 8 pulgadas (2.032m) de extensin entre el piso y
el transportador en los pasillos que no sean salidas deemergencia.
FIGURE 5A
-
8/13/2019 Manual Instalacion Cinta
6/36
6
If conveyors are to be used in an overhead application,ceiling hangers may have been supplied in place of floorsupports.
Figure 6A shows how a ceiling hanger mounts to a con-veyor section. Ceiling hangers should be mounted at sec-
tion joints. For safety information concerning conveyorsmounted overhead, refer to Installation Safety
Precautions on Page 4.
NOTE: When installing ceiling hanger rods in an existing
building, all methods of attachment must comply withlocal building codes.
Ceiling Hanger
Installationcho
Si los transportadores van a ser usados en aplicacionesareas o superiores, soportes de techo pudieron habersido suministrados en vez de los soportes de piso.
La Figura 6A muestra como un soporte de techo se instalaen un transportador. Los soportes deben montarse en la
unin de las secciones. Para informacin de seguridadrespecto al montaje de transportadores areos, refirase a
Medidas de Seguridad al Instalaren la pgina 4.
NOTA: Cuando se instalan varillas colgantes al techo en
una construccin existente, todos los mtodos de unindeben cumplir con los cdigos locales de construccin.
Instalacin de losSoportes de Techo
FIGURE 6A
-
8/13/2019 Manual Instalacion Cinta
7/36
Mark a chalk line on floor to locate center of the con-
veyor (Floor Mounted Conveyors).
Place the drive section in position.Install remaining sections placing end without support
on extend support of previous section (Figure 7A).
Check Match Mark Numbers to see that adjoining
sections are in proper sequence
Fasten sections together with splice plates and pivot
plates (Figure 7B). Hand tighten bolts only.
Check to see that conveyor is level across width and
length of unit. Adjust supports as necessary.
Tighten all splice plates and support mounting boltsand lag to the floor.
Install electrical controls and wire motor. See Page10.
Install and track belt per instructions on Pages 8 and
14.
1. . .
2. . .3. . .
4. . .
5. . .
6. . .
7. . .
8. . .
Marque con tiza una lnea en el suelo para ubicar el
centro del transportador. (Solamente para los
Transportadores Montados en el Piso).Coloque la seccin motriz en posicin.
Instale las secciones restantes, colocando el extremo
sin soporte en la placa pivote de la seccin anterior
(Figura 7A). Revise las etiquetas de secuencia de
armado y asegurese de que las secciones estn en el
orden correcto.
Sujete las secciones con placas de unin y placas
pivote (Figura 7B). Apriete los tornillos manualmente.
Revise si el transportador est nivelado a lo ancho ylargo de la unidad. Ajuste los soportes como sea
necesario.Apriete todas las placas de union y los tornillos de
montaje. Ancle el transportador al piso.
Instale los controles elctricos y conecte el motor
(Pag. 10).Instale y alinie la banda con las instrucciones de las
Pginas 8 y 14.
1. . .
2. . .
3. . .
4. . .
5. . .
6. . .
7. . .
8. . .
Conveyor Set-Up Montaje
FIGURE 7A
FIGURE 7B
-
8/13/2019 Manual Instalacion Cinta
8/36
8
NOTE: If belt ends cannot be pulled together by hand,
it may be necessary to loosen take-ups (at tail pulley,etc.), minimum position or use a belt puller so lacing
pin can be easily inserted.
NOTA: Si los extremos de la banda no pueden serunidos manualmente, afloje los tornillos tensores (enla polea de retorno, etc.) puede usar un jalador debanda hasta que el pasador pueda ser facilmenteinsertado.
CAUTION!Excessive slippage will reduce belt life and damage
drive pulley lagging. Never apply more tension than isneeded.
Over-tension will cause extra wear to belt and bearingsand will require extra power from drive.
P R E C A U C I O N !El patinaje excesivo reducir la vida de la banda y
daar el revestimiento de la polea motriz. Nuncaaplique mas tensin de la necesaria. Una sobre-tensincausar un desgaste extra de la banda y los rodamien -
tos, y requerir una mayor potencia de la unidad motriz.
The conveyor belt has been cut to the proper length and lac-ing installed at the factory. To install follow these steps:
Thread belt through conveyor as shown in Figure 9B.
Pull ends together and insert lacing pin (Figure 9A). If
belts ends cannot be pulled together by hand, loosen
take-ups (in center drive or at tail pulley) and/or use a
belt puller so lacing pin can be inserted.
Adjust belt tension with take-up pulley or tail pulley.
Keep pulley square by moving both take-up bolts an
equal amount. Maintain enough tension so drive pulley
will not slip when carrying the rated load.
Track belt per instructions on Page14.
1. . .
2. . .
3. . .
4. . .
La banda del transportador ha sido previamente cortada yenlazada en la fbrica. Para instalarla siga los siguientes
pasos:
Coloque la banda a travs del transportador (Fig. 9B).
Junte los extremos e incerte el pasador de enlace (Fig.
9A). Si los extremos no se pueden juntar manualmente
afloje los tensores (en el motor central o en la polea de
retorno) y/o use un jalador para que el pasador pueda
ser incertado.
Ajuste la tensin de la banda con las poleas tensoras
o con la polea de retorno. Mantenga la polea
encuadrada moviendo los tornillos tensores a la misma
distancia. Mantenga suficiente tension para que la
polea motriz no se resvale cuando transporte la carga
estimada.Alinie la banda de acuerdo a las instrucciones de la
pgina 14.
1. . .
2. . .
3. . .
4. . .
Belt Installation Instalacin de la Banda
-
8/13/2019 Manual Instalacion Cinta
9/36
BELT INSTALLATIONEND DRIVE
BELT INSTALLATIONCENTER DRIVE OR UNDERSIDE TAKE UP
(INSTALACION DE LA BANDAUNIDAD MOTRIZ DE EXTREMO)
(INSTALACION DE LA BANDAUNIDAD MOTRIZ CENTRAL O TENSORES INFERIORES)
FIGURE 9A
FIGURE 9B
-
8/13/2019 Manual Instalacion Cinta
10/36
-
8/13/2019 Manual Instalacion Cinta
11/36
All such emergency stop devices shall be easily identifi-able in the immediate vicinity of such locations unless
guarded by location, position, or guards. Where the design,function, and operation of such conveyor clearly is not haz-
ardous to personnel, an emergency stop device is notrequired.
The emergency stop device shall act directly on the con-trol of the conveyor concerned and shall not depend on the
stopping of any other equipment. The emergency stop
devices shall be installed so that they cannot be overridden
from other locations.
D) Inactive and unused actuators, controllers, and wiring
should be removed from control stations and panel boards,
together with obsolete diagrams, indicators, control labels,
and other material which serve to confuse the operator.
SAFETY DEVICES
A) All safety devices, including wiring of electrical safetydevices, shall be arranged to operate in a Fail-Safe man-ner, that is, if power failure or failure of the device itself
would occur, a hazardous condition must not result.
B) Emergency Stops and Restarts. Conveyor controls shallbe so arranged that, in case of emergency stop, manual
reset or start at the location where the emergency stop wasinitiated, shall be required of the conveyor(s) and associat-
ed equipment to resume operation.
C) Before restarting a conveyor which has been stoppedbecause of an emergency, an inspection of the conveyor
shall be made and the cause of the stoppage determined.
The starting device shall be locked out before any attemptis made to remove the cause of stoppage, unless operationis necessary to determine the cause or to safely remove the
stoppage.
Refer to ANSI Z244.1-1982, American National Standard forPersonnel Protection Lockout/Tagout of Energy Sources
Minimum Safety Requirements and OSHA StandardNumber 29 CFR 1910.147 The Control of Hazardous
Energy (Lockout/Tagout).
estn mas all del alcance de la voz y del contacto visual delas reas de conduccin, reas de carga, puntos de transfe
rencia y otros sitios potencialmente peligrosos localizadosen la trayectoria del transportador que no tenga proteccin,
ya sea dada por posicin, ubicacin, o guardas, debern serequipados con interruptores de parada de emergencia, cor
dones de parada de emergencia, interruptores de lmite odispositivos similares para paradas de emergencia.
Todos estos dispositivos de parada de emergencia
debern ser fcilmente identificables en las cercanas
inmediatas a estos puntos potencialmente peligrosos, a no
ser que estn protegidos dada su ubicacin, posicin o pro
tegidos con guardas. Donde el diseo, el funcionamiento, y
la operacin de tales transportadores no represente un claro
peligro para el personal, no se requieren los despositivos de
parada de emergencia.
El dispositivo de parada de emergencia deber actuar
directamente en el control del transportador concerniente y
no deber depender de la parada de cualquier otro equipo
Los dispositivos de parada de emergencia debern ser instalados de tal forma que no puedan ser anulados desde otrasl o c a l i d a d e s .
D) Los controles, los actuadores inactivos o no usados y loscables, debern ser removidos de las estaciones de controy de los tableros de mando, junto con los diagramas, indi
cadores, etiquetas de control y otros materiales obsoletos,los cuales se prestan para confundir al operador.
DISPOSITIVOS DE SEGURIDAD
A) Todos los dispositivos de seguridad, incluyendo la
conexin de dispositivos elctricos, deben ser dispuestos
para operar en una manera de autoproteccin; es decir, sise presenta una prdida de corriente o un fallo en el mismodispositivo, no debe presentarse una situacin peligrosa.
B) Paradas de Emergencia y Reactivadores. Los controles
del transportador debern estar dispuestos de tal maneraque en caso de una parada de emergencia, se requerir un
activador o arrancador manual en la ubicacin donde laparada de emergencia se presenta para reanudar la
operacin del transportador o transportadores y el equipoa s o c i a d o .
C) Antes de volver a poner en marcha un transportador que
haya sido detenido por una emergencia, debe revisarse ydeterminar la causa de la parada. El dispositivo de arranque
deber ser bloqueado antes de intentar corregir o remover lacausa que origin la parada, a no ser que la operacin del
transportador sea necesaria para determinar la causa o parasolucionar el problema de la parada sin ningn peligro.
Refirase a ANSI Z244.1-1982, American Nationa
Standard for Personnel Protection - Lockout/Tagout ofEnergy Sources - Minimum Safety Requirements and OSHA
Standard Number 29 CFR 1910.147 The Control oHazardous Energy (Lockout/Ta g o u t ) .
-
8/13/2019 Manual Instalacion Cinta
12/36
2
O P E R AT I O N
A ) Only trained employees shall be permitted to operate conveyors.
Training shall include instruction in operation under normal conditions and
emergency situations.
B ) Where employee safety is dependent upon stopping and/or starting
devices, they shall be kept free of obstructions to permit ready access.
C ) The area around loading and unloading points shall be kept clear of
obstructions which could endanger personnel.
D ) No person shall ride the load-carrying element of a conveyor under any
circumstances unless that person is specifically authorized by the owner
or employer to do so. Under those circumstances, such employee shall
only ride a conveyor which incorporates within its supporting structure,
platforms or control stations specifically designed for carrying personnel.
Under no circumstances shall any person ride on any element of a verti-
cal conveyor. Owners of conveyors should affix warning devices to the
conveyor reading Do Not Ride Conveyor.
E) Personnel working on or near a conveyor shall be instructed as to the
location and operation of pertinent stopping devices.
F ) A conveyor shall be used to transport only material it is capable of han-
dling safely.
G ) Under no circumstances shall the safety characteristics of the convey-
or be altered if such alterations would endanger personnel.
H ) Routine inspections and preventive and corrective maintenance pro-
grams shall be conducted to insure that all safety features and devices are
retained and function properly.
I ) Personnel should be alerted to the potential hazard of entanglement in
conveyors caused by items such as long hair, loose clothing, and jewelry.
J ) As a general rule, conveyors should not be cleaned while in operation.
Where proper cleaning requires the conveyor to be in motion and a haz-
ard exists, personnel should be made aware of the associated hazard.
O P E R A C I O N
A)Solo se debe permitir operar los transportadores a empleados entrenados.El entrenamiento debe incluir instrucciones de operacin bajo condiciones
normales y en situaciones de emergencia.
B )Donde la seguridad de los trabajadores dependa de dispositivos de para -da y/o arranque, stos debern mantenerse libres de obstrucciones para per -
mitir un acceso rpido.
C )El rea alrededor de los puntos de carga y descarga debe mantenerselibre de obstrucciones, las cuales podran poner en peligro al personal.
D )Ninguna persona debe montarse en la parte de conduccin de carga deun transportador bajo ninguna circunstancia al menos que esta persona est
especficamente autorizada por el dueo o por el supervisor. Bajo estas cir -
cunstancias, el empleado deber montarse solamente en un transportadorque tenga incorporado dentro de su estructura, plataformas o estaciones de
control especialmente diseadas para el traslado de personal. Bajo ningunacircunstancia, persona alguna debe subirse en cualquier parte de un trans -
portador vertical. Los dueos de los transportadores deben aadir seales de
advertencia al transportador con el texto: No Montarse en el Tr a n s p o r t a d o r .
E )El personal que est trabajando en o cerca al transportador, deber serinstrudo en cuanto a la ubicacin y operacin de los dispositivos pertinentesde parada.
F )Un transportador deber ser usado para transportar solo los productos quesea capaz de manejar seguramente.
G )Bajo ninguna circunstancia debern ser alteradas las caractersticas deseguridad de un transportador, si tales alteraciones pudieran poner en peligro
al personal.
H) Inspecciones rutinarias debern llevarse a cabo al igual que programas
preventivos y correctivos de mantenimiento, para asegurar que todos los dis -positivos y medidas de seguridad sean conservados en buen estado y fun -cionen correctamente.
I )El personal deber ser avisado de peligros potenciales como enredos entransportadores causados por materiales como cabello largo, ropa suelta oj o y a s .
J )Como regla general, los transportadores no debern limpiarse mientrasestn en funcionamiento. Cuando se requiera limpiar el transportador
estando en movimiento y exista posibilidad de peligro, el personal deber ser
avisado de este riesgo.
Conveyor Start-UpBefore conveyor is turned on, check for foreign objects that mayhave been left inside conveyor during installation. These objects
could cause serious damage during start-up.After conveyor has been turned on and is operating, check motors,
reducers, and moving parts to make sure they are working freely.
Arranque del Transportador
PRECAUCION!Debido a la cantidad de partes en movimiento del trans -
portador, todo el personal en el rea del transportadornecesita ser advertido de que este est a punto de
ponerse en marcha.
Antes de poner en marcha el transportador, revise si hay objetos
ajenos que puedan haber sido dejados dentro del transportadordurante la instalacin. Estos objetos pueden causar serios daos
en el arranque.
Despus de que el transportador arranque y est operando, revise
los motores, reductores y partes en movimiento para estar segurode que estn trabajando libremente.
CAUTION!Because of the many moving parts on the conveyor, all
personnel in the area of the conveyor need to bewarned that the conveyor is about to be started.
Operation Safety Precautions Medidas de Seguridad
-
8/13/2019 Manual Instalacion Cinta
13/36
The drive chain is pre-lubricated from the manufacturer by a hot dip-
ping process that ensures total lubrication of all components.
H o w e v e r, continued proper lubrication will greatly extend the useful lifeof every drive chain.
Drive Chain lubrication serves several purposes including: Protecting against wear of the pin-bushing joint
Lubricating chain-sprocket contact surfaces Preventing rust or corrosion
For normal operating environments, lubricate every 2080 hours ofoperation or every 6 months, whichever comes first. Lubricate with agood grade of non-detergent petroleum or synthetic lubricant (i.e.,
Mobile 1 Synthetic). For best results, always use a brush to gener-ously lubricate the chain. The proper viscosity of lubricant greatlya ffects its ability to flow into the internal areas of the chain. Refer tothe table below for the proper viscosity of lubricant for your application.
The drive chains lubrication requirement is greatly affected by theoperating conditions. For harsh conditions such as damp environ-ments, dusty environments, excessive speeds, or elevated tempera-tures, it is best to lubricate more frequently. It may be best, underthese conditions, to develop a custom lubrication schedule for yourspecific application. A custom lubrication schedule may be developedby inspecting the drive chain on regular time intervals for suff i c i e n tlubrication. Once the time interval is determined at which the chain isnot sufficiently lubricated, lubricate it and schedule the future lubrica-
tion intervals accordingly.
A ) Maintenance, such as lubrication and adjustments, shall be per-
formed only by qualified and trained personnel.
B ) It is Important that a maintenance program be established to
insure that all conveyor components are maintained in a condition
which does not constitute a hazard to personnel.
C ) When a conveyor is stopped for maintenance purposes, startingdevices or powered accessories shall be locked or tagged out in accor-
dance with a formalized procedure designed to protect all person or
groups involved with the conveyor against an unexpected start.
D ) Replace all safety devices and guards before starting equipment
for normal operation.
E ) Whenever practical, DO NOT lubricate conveyors while they are
in motion. Only trained personnel who are aware of the hazard of the
conveyor in motion shall be allowed to lubricate.
S A F E T Y G U A R D SMaintain all guards and safety devices IN POSITION and IN SAFE
R E PA I R .
WARNING SIGNSMaintain all warning signs in a legible condition and obey all warnings.
See Page 3 of this manual for examples of warning signs.
A )El mantenimiento, tal como lubricacin y ajustes, debe ser realizado solmente por personal calificado y entrenado.
B )Es importante que se establezca un programa de mante- nimiento, paasegurar que todos los componentes del transportador sean mantenidos econdiciones que no constituyan un peligro para el personal.
C )Cuando un transportador est parado por razones de mante-nimientlos dispositivos de arranque o accesorios motorizados debern ser asegrados o desconectados conforme a un procedimiento formalizado, dieado para proteger de cualquier arranque inesperado a toda persona grupos de personas involucrados con el transportador, de un arranque inep e r a d o .
D )Antes de poner en marcha el equipo en una operacin normal, vuelva colocar todos los dispositivos de seguridad y las guardas.
E )Siempre que sea prctico, N Olubrique los transportadores mientras sencuentren en movimiento. Solo el personal entrenado, que tengconocimiento de los peligros del transportador en movimiento, se le permtir hacer la lubricacin.
PROTECCIONES DE SEGURIDADMantenga todas las guardas y dispositivos de seguridad EN SU POSICIOy EN BUENAS CONDICIONES.
SEALES DE A D V E RT E N C I AMantenga todas las seales de advertencia en condiciones legibles obedzcalas. Remtase a la pgina 3 de este manual para ver ejemplos dseales de advertencia.
M A I N T E N A N C E M A N T E N I M I E N TO
Maintenance SafetyPrecautions
Medidas de Seguridaden el Mantenimiento
La cadena motriz ha sido pre-lubricada por el fabricante mediante un proceso de sumersin caliente que asegura una lubricacin total de todos suscomponentes. Sin embargo, una lubricacin apropiada y continua extender su vida til considerablemente.
La lubricacin de la cadena motriz cumple varios propsitos: Proteger contra el desgaste de la unin de pines de la cadena Lubricar las superficies de contacto entre la cadena
y la catarina Prevenir la oxidacin o corrosin.
En operaciones bajo condiciones ambientales normales, lubrique cada2080 horas de operacin o cada 6 meses, lo que ocurra primero. Lubriquecon un lubricante sinttico (ej. Mobile 1 sinttico) o basado en petroleo nodetergente de buen grado. Para mejores resultados, siempre utilice unabrocha para lubricar la cadena generosamente. La viscosidad apropiadadel lubricante afecta enormente el fluido del mismo hacia las reas internasde la cadena. Refirase a la siguiente tabla para consultar la viscosidad delubricante adecuada para su aplicacin.
El requerimiento de lubricacin de la cadena motriz se v afectado considerablemente por las condiciones de operacin. En condiciones difcilestales como: ambientes humedos, ambientes con polvo, velocidades excesivas, o temperaturas elevadas, se recomienda lubricar la cadena con msfrecuencia. Lo mejor sera que bajo estas condiciones se establezca un programa de lubricacin especfico para su aplicacin. Este programa especfico puede desarrollarse mediante la inspeccin de la lubricacin de lacadena motriz en intervalos regulares de tiempo. Una vez se ha determinado el intervalo en el cual la cadena no se encuentra suficientemente lubricada, lubrquela y programe los siguientes intervalos de acuerdo al intervalo anterior.
Lubrication Lubricacin
Ambient Temperature SAE ISO
Degrees F20-40 20 46 or 6840-100 30 100100-120 40 150
Temperatura A m b i e n t e S A E I S O
(Grados F) (Grados C)2 0 - 4 0 -07 04 2 0 46 o 68 4 0 - 1 0 0 04 38 3 0 1 0 0 1 0 0 - 1 2 0 38 49 4 0 1 5 0
-
8/13/2019 Manual Instalacion Cinta
14/36
4
HOW IS THE CONVEYOR BELT TRACKEDThe belt is tracking by adjusting: Drive Pulley, Tail Pulley,
Return Idlers, and Snub Idlers. The same tracking principlesapply to conveyors supplied with end drives, center drives,
or underside take-ups.
PRE-TRACKING INSPECTION
Before attempting to physically track the belt:
Make sure conveyor is level across the width and
length of unit. Adjust supports as necessary.Check to make sure: Drive Pulley, Tail Pulley, Snub
Idlers, and all Return Idlers are square with conveyorbed. See illustrations 14A, 14B, 15A, 15B and 15C.
Dimension A should be equal on both sides of unit.Make sure belt has been properly threaded through
conveyor. See Belt Installation, Page 8.Check for improper loading. Feed should be in direc-
tion of belt travel, centered on belt.Make sure belt lacing has been installed correctly and
is square with the belt.
1. . .
2. . .
3. . .
4. . .
5. . .
COMO SE ALINEA LA BANDA DEL TRANSPORTADORLa banda se alinea al ajustar: La Polea Motriz, Polea de
Retorno, Rodillos de Retorno, y Rodillos de Alineacin.Los mismos principios de ajuste se aplican a los trans -
portadores de unidad motriz de extremo, unidad motrizcentral o tensores inferiores.
INSPECCION PRE-ALINEACIONAntes de intentar alinear la banda:
Asegrese de que el transportador est nivelado a lo
ancho y largo de la unidad. Ajuste los soportes comosea necesario.
Asegrese de que la Polea Motriz, la Polea deRetorno, y los Rodillos de Alineacin y de Retorno
estn encuadrados con la cama del transportador(Fig. 14A a la 15C). La Dimensin A debe ser igual
en ambos lados de la unidad.Asegures de que la banda haya sido propiamente
colocada en el transportador. Vea Instalacin de laBanda, Pg. 8.
Revise si es cargado impropiamente. El alimentadordebe estar en direccin hacia donde la banda viaja,
centrado en la banda.Asegrese de que el enlace est correctamente
instalado y encuadrado con la banda.
1. . .
2. . .
3. . .
4. . .
5. . .
Belt Tracking Alineacin de la Banda
SQUARING 4 END DRIVE SQUARING 8 END DRIVE
FIGURE 14A FIGURE 14B
-
8/13/2019 Manual Instalacion Cinta
15/36
SQUARING RETURN PULLEY SQUARING TAIL PULLEY
SQUARING PULLEYS IN CENTER DRIVEOR UNDERSIDE TAKE-UP
PRECAUCION!Solo el personal entrenado deber ajustar la banda deltransportador ya que se debe hacer cuando el trans -
portador est operando.
CAUTION!Only trained personnel should track conveyor belt which
must be done while conveyor is in operation.
FIGURE 15A
FIGURE 15C
FIGURE 15B
-
8/13/2019 Manual Instalacion Cinta
16/36
6
IMPORTANTE: Cuando se hagan ajustes a la bandadebern hacerse lo menor posible (1/16 a la vez en los
rodillos de retorno, etc. ser suficiente).
Dele a la banda el tiempo adecuado para que se ajuste. En
transportadores largos y lentos, tal vez tomar variasvueltas antes de que quede ajustado.
A)Prese en la polea de retorno y observe hacia que direc -cin la banda corre.
B)Despues de haber observado la banda y determinado elajuste, siga los procedimientos en Como Dirigir la Banda,
Vea la Figura 16A.
COMO DIRIGIR LA BANDACondicin 1. . .Cuando la banda est corriendo endireccin de la flecha (FLUJO), pero se desvia hacia elLADO X, mueva el Rodillo de Alineacin ms cercano del
extremo de CARGA del LADO Y hacia el extremo de
DESCARGA del transportador.Condicin 2. . . Cuando la banda est corriendo en direc -cin de la flecha (FLUJO) pero se desvia hacia el LADO
Y, mueva el Rodillo de Alineacin mas cercano al extremode CARGA del LADO X hacia el extremo de DESCARGA
del transportador.S la banda corre en reversa del FLUJO, todas las condi -
ciones sern las mismas (Figura 16A), exceptuando queahora usted est viendo el transportador por el ladoopuesto.S la banda continua estando mal alineada entonces revise
todos los objetivos de la seccin Inspeccin Pre-Alineacin y haga las correcciones necesarias.
IMPORTANT: When belt tracking adjustments are made,
they should be minor (1/16 in. at a time on idlers, etc.,
should be sufficient.).
Give the belt adequate time to react to the adjustments. It
may take several complete revolutions around the convey-or for the belt to begin tracking properly on long, slow con-
veyor lines.A) Stand at tail pulley looking toward drive and note what
direction belt is traveling.B) Having observed belt and determined tracking problem,
follow procedures in How to Steer The Belt, See Figure16A.
HOW TO STEER THE BELT
Condition 1. . .When the belt is running in the direction(FLOW) with the arrow, but tracking (drifting) towards Side
X, move the Snub Idler nearest the INFEED end of Side
Y towards the DISCHARGE end of the conveyor.Condition 2. . . When the belt is running in the direction(FLOW) with the arrow, but tracking (drifting) towards Side
Y, move the Snub Idler nearest the INFEED end of SideX towards the DISCHARGE end of the conveyor.
If Belt Direction (FLOW) is reversed, all the above condi-tions will remain the same as in Figure 16A, except you arenow viewing the conveyor from the opposite end.If belt continues to track improperly, re-check all items cov-
ered in Pre-Tracking Inspection and make corrections asnecessary.
NOTE: In all conditions, you are viewing the ConveyorBelt from the INFEED end. All corrections will be made
from the INFEED end of conveyor.
NOTA: En todas las condiciones, el transportador seobservar desde el punto de CARGA. Todas lascorreciones sern hechas desde este mismo punto.
FIGURE 16A
-
8/13/2019 Manual Instalacion Cinta
17/36
CAUTION!Never remove chain
guards while the convey-or is running. A l w a y s
replace guards afteradjustments are made.
CHAIN TOO TIGHT(REQUIRES EXTRA POWER)
CHAIN TOO LOOSE
CORRECT SLACKAPPROX. 1/4 OR
2% OF SPROCKET CENTERS
SPROCKET CENTERS
The drive chain and sprockets should be checked periodi-cally for proper tension and alignment. Improper adjustmentwill cause extensive wear to the drive components.
TO MAKE ADJUSTMENTS
Remove chain guard.Check sprocket alignment by placing a straightedge
across the face of both sprockets (Figure 17A).Loosen set screws and adjust as needed. Re-tighten
set screws.To adjust chain tension, loosen bolts that fasten motor
base to mounting angles, both sides of the conveyor.Tighten take-up bolts until desired chain tension is
reached. (Figures 17B & 17C). Re-tighten mountingbolts.
Lubricate chain per lubrication instructions.Replace chain guard so that it does not interfere with
drive.
1. . .
2. . .
3. . .
4. . .
5. . .
MOTOR/REDUC-ER DRIVE
DRIVEPULLEY
MOUNTINGBOLTS
PRECAUCION!Nunca remueva la guar -
da de cadena mientrasel transportador est en
funcionamiento. Siemprevuelva a colocar lasguardas despus de que
los ajustes se hayanhecho.
La cadena motriz y las catarinas debern ser revisadasperidicamente para mantener su apropiada tensin yalineacin. Ajustes incorrectos causarn un desgaste exce
sivo a los componentes de la transmisin.
PARA HACER AJUSTES
REDUCERSPROCKET
GEAR REDUCER
DRIVE SHAFTSPROCKET
SET SCREWS
STRAIGHT EDGE(NIVEL)
(CATARINA DEL
REDUCTOR)
(TORNILLOS CANDADOS)(EJE DE
TRANSMISION)
(REDUCTOR)
(POLEAMOTRIZ)
(TORNILLOS DE
MONTAJE)
(MOTOR/REDUCTORMOTRIZ)
(CADENA DEMASIADO TENSA
[REQUIERE MAS POTENCIA])
(CADENA DEMASIA -
DO FLOJA)
(TENSION CORRECTA)(1/4 O 2% DE CENTROS DE
CATARINAS APROX.)
(CENTROS DECATARINAS)
DRIVE PULLEYSPROCKET
(CATARINA DE LAPOLEA MOTRIZ)
REDUCERSPROCKET(CATARINA DEL
REDUCTOR)
TAKE-UPBOLTS
(TORNILLOSTENSORES)
MOTOR BASE PLATE
(PLACA DEL MOTORBASE)
Remueva la guarda cadena.
Verifique la alineacin de las catarinas colocando un
nivel sobre las caras de ambas catarinas. (Figura17A). Afloje los tornillos candados y ajuste tanto
como sea necesario. Apriete los tornillos candados.
Para ajustar la tensin de la cadena, afloje los tornil -los que aseguran la base del motor a los ngulos de
montaje, a ambos lados del transportador.
Apriete los tornillos tensores hasta obtener la tensin
correcta de la cadena (Figuras 17B & 17C). Apriete
los tornillos de montaje.
Lubrique la cadena de acuerdo a las instrucciones delubricacin.
Coloque la guarda de cadena para que no interfiera
con la transmisin.
1. . .
2. . .
3. . .
4. . .
5. . .
Drive Chain Alignment
and Tension
Alineacin y Tensin dela Cadena Motriz
FIGURE 17A
FIGURE 17B FIGURE 17C
-
8/13/2019 Manual Instalacion Cinta
18/36
Trouble Shooting
8
The following charts list possible problems that may occur in the operation of a powered conveyor.
TROUBLE SHOOTING DRIVES
TROUBLE CAUSE SOLUTION
Conveyor will not start or motor quits fre-quently.
Drive chain and sprockets wear excessively.
Loud popping or grinding noise.
Motor or reducer overheating.
Belt does not move, but drive runs.
1) Motor is overloaded.2) Motor is drawing too much current.
1) Lack of lubrication on chain causing chainstretch which creates improper chain tosprocket mesh.
2) Sprockets are out of alignment.3) Loose chain.
1) Defective bearing.2) Loose set screws in bearing.3) Loose drive chain.
1) Conveyor is overloaded.
2) Low voltage to motor.3) Low lubricant level in reducer.
1) Conveyor is overloaded.2) Belt is too loose.3) Lagging on drive pulley is worn.
1) Check for overloading of conveyor.2) Check heater or circuit breaker and change if necessary.
1) Replace chain and sprockets. Provide adequate lubrication.NOTE: If problem reoccurs, a chain take-up may be required.
2) Align sprockets. See Drive Chain Alignment and Tension.3) Tighten chain.
1) Replace bearing.2) Tighten set screw.3) Tighten chain.
1) Check capacity of conveyor and reduce load to recommendedlevel.
2) Have electrician check and correct as necessary.3) Relubricate per manufacturers recommendations. For HYTROL
reducer, refer to separate manual.
1) Reduce load.2) Use belt take-up to tighten belt.3) Replace drive pulley lagging and tighten belt.
TROUBLE SHOOTING DRIVE BELT TRACKING
TROUBLE CAUSE SOLUTION
Entire length of belt creeps off at one spotonly.
Belt creeps to one side at tail pulley.
Entire belt creeps to one side.
1) One or more idlers (usually near troublespot) are out of line.
2) One conveyor section not level or square.3) Material build-up on pulleys or idlers.
1) Tail pulley, return idler, or snub idler neartail pulley not properly aligned or squarewith bed.
1) Conveyor not straight.2) Conveyor not level.
3) Material build-up on rollers, pulleys, oridlers.
1) Adjust idlers as necessary. See Tracking the belt in this manualfor details.
2) Make necessary adjustments to supports.3) Remove residue from pulleys or idlers. install belt, cleaners, or
scrappers if possible.
1) Adjust as necessary. See Belt Tracking Pre-Tracking Inspectionin this manual for details.
1) Re-align bed sections as necessary.2) Correct as necessary.
3) Remove residue and install belt cleaners or scrapers if possible.
-
8/13/2019 Manual Instalacion Cinta
19/36
Resolviendo Problemas
Los siguientes cuadros describen posibles problemas que pueden ocurrir en la operacin de un transportador motorizado.
RESOLVIENDO PROBLEMAS DE TRANSMISION
PROBLEMA CAUSA SOLUCION
El transportador no arranca o el motor sedetiene frecuentemente.
Desgaste excesivo de la cadena motriz ylas catarinas.
Funcionamiento muy ruidoso.
Motor o reductor recalentado.
La banda no se mueve, pero el motor corre.
1) El motor est sobrecargado.2) El motor pasa demasiada corriente.
1) Falta de lubricacin en la cadenacausando su extensin lo cual crea unacadena inapropiada.
2) Los catarinas estn desalineadas.3) La cadena est floja.
1) Rodamientos defectuosos.2) El tornillo candado est flojo.3) La cadena est floja.
1) Transportador est sobrecargado.
2) Bajo voltaje al motor.3) Bajo nivel de lubricante en reductor.
1) El transportador est sobrecargado.2) La banda est floja.3) El revestimiento de la polea motriz esta gastada.
1) Revise si hay sobrecarga del transportador.2) Revise los circuitos e interruptores de proteccin y sobrecarga, y
cmbielos si es necesario.
1) Reemplaze la cadena y las catarinas. Proporcione una adecuadalubricacin. NOTA: Si se presentan problemas, posiblemente serequiere tensionar la cadena.
2) Alinee catarinas. Vea Alineacin y Tensin de Cadena Motriz .3) Tensione la cadena.
1) Reemplaze los baleros.2) Apriete el tornillo candado.3) Tensione la cadena.
1) Revise la capacidad del transportador y reduzca la carga al nivel recomend a d o .
2) Haga un chequeo por un electricista y corrija si es necesario.3) Vuelva a lubricar de acuerdo a las recomendaciones del fabri-
cante. Para el reductor HYTROL, refirase al manual adjunto.
1) Reduzca la carga.2) Use tensores de banda para apretar la banda.3) Reemplaze el revestimiento de la polea y apriete la banda.
RESOLVIENDO PROBLEMAS DE ALINEACION DE LA BANDA MOTRIZ
PROBLEMA CAUSA SOLUCION
La banda se desliza en un punto.
La banda se desliza hacia un lado en la poleade retorno.
Toda la banda se desliza hacia un lado.
1) Uno o ms rodillos (usualmente cerca delpunto del problema) estn desalineados.
2) Una o ms secciones estn desniveladaso desencuadradas.
3) Acumulacin de material en rodillos opoleas.
1) La polea de retorno, rodillo de retorno o el rodil -lo de alineacin cerca de la polea de retorno noest alineada o encuadrada con la cama.
1) El transportador no est derecho.
2) El transportador no est nivelado.3) Material acumulado en rodillos o poleas.
1) Ajuste los rodillos como sea necesario. Use la seccin Alineacinde la banda como referencia.
2) Ajuste los soportes como sea necesario.3) Remueva el residuo de los rodillos o poleas. Aplique los
limpiadores de banda o raspadores si es posible.
1) Ajuste como sea necesario. Vea Inspeccin Pre-Alineacin de laBanda en este manual.
1) Realinie las secciones de cama como sea necesario.
2) Conecte como sea necesario.3) Remueva el residuo y aplique los limpiadores de banda o ras
padores si es posible.
-
8/13/2019 Manual Instalacion Cinta
20/36
20
The following is a general maintenance checklist which covers the major components of your conveyor.
This will be helpful in establishing a standard maintenance schedule.
Preventive Maintenance Checklist
-
8/13/2019 Manual Instalacion Cinta
21/36
La siguiente es una lista de verificacin del mantenimiento preventivo, la cual cubre los principales componentes de su trans
portador. Esta ser til para establecer un programa estndar de mantenimiento.
Lista de Mantenimiento Preventivo
-
8/13/2019 Manual Instalacion Cinta
22/36
22
Included in this manual are parts drawings with complete replacement parts lists. Minor fasteners, such as nuts and bolts,are not included.
When ordering replacement parts:
Contact Dealer from whom conveyor was purchasedor nearest HYTROL Distributor.
Give Conveyor Model Number and Serial Number orHYTROL Factory Order Number.
Give Part Number and complete description from PartsList.
Give type of drive. Example8 End Drive, 8 CenterDrive, etc.
If you are in a breakdown situation, tell us.
1. . .
2. . .
3. . .
4. . .
5. . .
How to Order Replacement Parts
HYTROL Serial Number(Located near Drive on
Powered Models).
-
8/13/2019 Manual Instalacion Cinta
23/36
Dibujo de las partes con listas completas de las refacciones estn incluidos en este manual. Aseguradores menores,como tornillos y tuercas no estn incluidos.
Para ordenar partes de repuesto:
Contacte la persona que le vendi el transportador oel distribuidor de Hytrol ms cercano.
Proporcione el Modelo del Transportador y el Nmerode Serie o Nmero de la Orden de Fabricacin.
Proporcione el Nmero de las partes y descripcincompleta de la Lista de Partes.
Proporcione el tipo de motor. EjemploUnidad Motrizde 8 en el Extremo, Unidad Motriz Central 8 , etc.
Si est en una situacin crtica, comunqueseinmediatamente.
1. . .
2. . .
3. . .
4. . .
5. . .
Nmero de Serie HYTROL(Localizado cerca a laUnidad Motriz en losmodelos motorizados).
Como Ordenar Partes de Repuesto
-
8/13/2019 Manual Instalacion Cinta
24/36
24
Model TR Parts Drawing (4" End Drive)
Dibujo de Partes Modelo TR (4" Unidad Motriz de Extremo)
OAW
BED
WIDTH
SECTION A-A
-
8/13/2019 Manual Instalacion Cinta
25/36
Model TR Parts List (4" End Drive)
Lista de Partes del Modelo TR (4" Unidad Motriz de Extremo)
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description32 041.201 Hex Jam Nut1/2-1333 042.919 Shoulder Bolt1/2 in. Dia. x .312 Long
34 041.919 Acorn Hex Nut 3/8-1635 B-09508 1.9 in. Dia. Return Idler (Specify OAW)36 B-22221 4 in. Dia. Tail Pulley (Specify OAW)37 B-19614-R Take-Up P late AssemblyRH38 B-19614-L Take-Up Plate AssemblyLH39 BeltBlack Ultimate 140 BOS (Specify Width)40 U3 Clipper Unibar Belt Lacing (Specify Length)41 #13 Lacing Pin (Specify Length)42 B-13708 Snub Roller Guard (Specify OAW)43 B-13707 Snub Roller Guard Mounting Bracket44 049.310 U-Type Speed Nut1/4-2045 B-09859 Nip Point Guard Tail End (Specify OAW)46 MS Type Pivot Plate1-1/2 in. Flange B-00913 3-11/16 in. High B-02112 1-9/16 in. High47 Floor Support Frame B-00914 6 in. High (Specify OAW) B-12777 7 in. High (Specify OAW)
B-12778 8 in. High (Specify OAW) B-00915 9 in. High (Specify OAW) B-00916 11-1/2 in. High (Specify OAW) B-00917 14-1/2 in. High (Specify OAW) B-02098 18-1/2 in. High (Specify OAW) B-00919 22-1/2 in. High (Specify OAW) B-00921 32-1/2 in. High (Specify OAW) B-00923 44-1/2 in. High (Specify OAW) B-00925 56-1/2 in. High (Specify OAW) B-02107 68-1/2 in. High (Specify OAW) B-02109 78-1/2 in. High (Specify OAW) B-02111 90-1/2 in. High (Specify OAW)48 B-00911 Adjustable Foot Assembly (Specify Length)
Ref. No. Part No. Description1 MotorC-Face 030.7134 1/2 HP230/460 VAC3 Ph.60 Hz.TEFC
030.7324 1 HP230/460 VAC3 Ph.60 Hz.TEFC2 Speed Reducer R-00153-30R 4ACRH30:1 Ratio R-00164-30R 5ACRH30:1 Ratio3 052.145 Coupling KitMotor to Reducer (1/2 1 HP)4 SprocketReducer 028.115 50B15 x 1 in. Bore (4AC) 028.117 50B15 x 1-1/4 in. Bore (5AC)5 028.115 SprocketDrive Pulley, 50B15 x 1 in. Bore6 029.101 #50 Riveted Roller Chain7 029.201 Connector Link#50 Roller Chain8 B-21417 4 in. Dia. Drive Pulley (Fully Lagged) (Specify OAW)9 B-07987 Bearing Spacer10 B-21422-R Dr ive Plate AssemblyRH11 B-21422-L Dr ive Plate AssemblyLH12 B-18909 Nip Point Guard Drive End (Specify OAW)13 010.102 3-Bolt Flange Bearing1 in. Bore14 090.203 Shaft Key1/4 in. Sq. x 1 in. Long
15 B-05545 Motor Base Support AngleRH16 B-05540 Motor Base Support AngleLH17 B-06629 Motor Base Assembly (Specify OAW)18 040.307 Take-Up Bolt3/8-16 x 2-1/4 in. Long19 041.300 Hex Jam NutHeavy3/8-1620 B-02308 Chain Guard Front Plate21 B-04246 Chain Guard Back PlateRH22 098.150 Spacer-13/32 in. I.D. x 3/4 in. O.D. x 3/8 in. Long23 041.919 Acorn Nut3/8-1624 093.215 Return Roller Bracket25 B-06742 2-1/8 in. Dia. Snub Roller (Specify OAW)26 Bed B-09516 5 ft. Long (Specify Bed Width) B-09517 10 ft. Long (Specify Bed Width)27 B-01944 Splice Plate28 B-20237 Connector Strap29 B-02057 Support Bar (Specify Bed Width)30 B-19619 Attachment Plate Assembly
31 040.407 Take-Up Bolt1/2-13 x 4 in. Long
-
8/13/2019 Manual Instalacion Cinta
26/36
26
Model TR Parts Drawing (8" End Drive)
Dibujo de Partes Modelo TR (8" Unidad Motriz de Extremo)
SECTION A-A
OAW
BED
WIDTH
-
8/13/2019 Manual Instalacion Cinta
27/36
Ref. No. Part No. Description1 MotorC-Face 030.7134 1/2 HP230/460 VAC3 Ph.60 Hz.TEFC 030.7324 1 HP230/460 VAC3 Ph.60 Hz.TEFC2 Speed Reducer R-00153-30R 4ACRH30:1 Ratio R-00164-30R 5ACRH30:1 Ratio3 052.145 Coupling KitMotor to Reducer (1/2 - 1 HP)4 SprocketReducer 028.133 50B14 x 1 in. Bore (4AC) 028.1342 50B16 x 1-1/4 in. Bore (5AC)5 SprocketDrive Pulley 028.13832 50B28 x 1-3/16 in. Bore (4AC) 028.1115 50B32 x 1-3/16 in. Bore (5AC)6 029.101 #50 Riveted Roller Chain7 029.201 Connector Link#50 Roller Chain8 B-00874 8 in. Dia. Drive Pulley (Ful ly Lagged) (Specify OAW)
9 B-09728-R Drive Plate AssemblyRH10 B-09728-L Drive Plate AssemblyLH11 B-09863 Nip Point GuardDrive End (Specify OAW)12 010.202 4-Bolt Flange Bear ing1-3/16 in. Bore13 090.203 Shaft Key1/4 in. Sq. x 1 in. Long14 B-05545 Motor Base Support AngleRH15 B-05540 Motor Base Support AngleLH16 B-06629 Motor Base Assembly (Specify OAW)17 040.307 Take-Up Bolt3/8-16 x 2-1/4 in. Long18 041.300 Hex Jam NutHeavy3/8-1619 B-04801 Chain Guard Front Plate20 B-04803 Chain Guard Back Plate21 098.150 Spacer-13/32 in. I .D. x 3/4 in. O.D. x 3/8 in. Long22 040.31115 Hex Head Bol t, 3/8-16 x 3-1/4 in. Long23 041.200 Hex Jam Nut, 3/8-1624 041.919 Acorn Nut3/8-1625 093.215 Return Roller Bracket26 B-06742 2-1/8 in. Dia. Snub Roller (Specify OAW)27 Drive Bed B-09751 5 ft. Long (Specify Bed Width) B-09753 10 ft. Long (Specify Bed Width)28 Intermediate/Tail Bed B-09516 5 ft. Long (Specify Bed Width) B-09517 10 ft. Long (Specify Bed Width)29 B-01944 Splice Plate30 B-20237 Connector Strap31 B-02057 Support Bar (Specify Bed Width)32 B-19619 Attachment Plate Assembly
Model TR Parts List (8" End Drive)
Lista de Partes del Modelo TR (8" Unidad Motriz de Extremo)
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description33 042.919 Shoulder Bolt, 1/2 in. Dia. x .312 Long34 040.407 Take-Up Bolt1/2-13 x 4 in. Long35 041.201 Hex Jam Nut1/2-1336 B-09508 1.9 in. Dia. Return Idler (Specify OAW)37 B-22221 4 in. Dia. Tail Pulley (Specify OAW)38 B-07987 Bearing Spacer39 B-19614-R Take-Up Plate AssemblyRH40 B-19614-L Take-Up Plate AssemblyLH41 010.102 3-Bolt Flange Bearing1 in. Bore42 B-09859 Nip Point GuardTail End (Specify OAW)43 BeltBlack Ultimate 140 BOS (Specify Width)44 U3 Clipper Unibar Belt Lacing (Specify Length)45 #13 Lacing Pin (Specify Length)46 B-13737 Snub Roller Guard (Specify OAW)47 B-13708 Snub Roller Guard (Specify OAW)48 B-13707 Snub Roller Guard Mounting Bracket
49 049.310 U-Type Speed Nut1/4-2050 MS Type Pivot Plate1-1/2 in. Flange B-00913 3-11/16 in. High B-02112 1-9/16 in. High51 Floor Support Frame B-00914 6 in. High (Specify OAW) B-12777 7 in. High (Specify OAW) B-12778 8 in. High (Specify OAW) B-00915 9 in. High (Specify OAW) B-00916 11-1/2 in. High (Specify OAW) B-00917 14-1/2 in. High (Specify OAW) B-02098 18-1/2 in. High (Specify OAW) B-00919 22-1/2 in. High (Specify OAW) B-00921 32-1/2 in. High (Specify OAW) B-00923 44-1/2 in. High (Specify OAW) B-00925 56-1/2 in. High (Specify OAW) B-02107 68-1/2 in. High (Specify OAW) B-02109 78-1/2 in. High (Specify OAW) B-02111 90-1/2 in. High (Specify OAW)52 B-00911 Adjustable Foot Assembly (Specify Length)
-
8/13/2019 Manual Instalacion Cinta
28/36
28
Model TR Parts Drawing (4" & 8" Center Drive)
Dibujo de Partes Modelo TR (4" & 8" Unidad Motriz Central)
SECTION A-A SECTION B-B
OAW
BEDWIDTH
-
8/13/2019 Manual Instalacion Cinta
29/36
Model TR Parts List (4" & 8" Center Drive)
Lista de Partes del Modelo TR (4" & 8" Unidad Motriz Central)
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description1 Drive Bed Assembly (Specify Bed Width) B-09521 Intermediate Drive2 Tail/Intermediate Bed B-09516 5 ft. Long (Specify Bed Width) B-09517 10 ft. Long (Specify Bed Width)3 B-01944 Splice Plate4 B-20237 Connector Strap5 B-02057 Support Bar (Specify Bed Width)6 B-00944 7/16 in. Hex Idler Bracket (At Drive)7 B-03894 2-1/8 in. Dia. Snub Idler (At Drive) (Specify Bed Width)
8 093.215 Return Roller Bracket9 B-06742 2-1/8 in. Dia. Snub Idler (At Tail ) (Specify OAW)10 B-09508 1.9 in. Dia. Ret. Idler-Int. (Not Shown) (Specify OAW)11 B-19619 Attachment Plate Assembly12 040.407 Take-Up Bolt1/2-13 x 4 in. Long13 041.201 Hex Jam Nut1/2-1314 042.919 Shoulder Bolt1/2 in. Dia. x .312 Long15 041.919 Acorn Hex Nut3/8-1616 B-22221 4 in. Dia. Tail Pulley (Specify OAW)17 B-07987 Bearing Spacer18 B-19614-R Take-Up Plate AssemblyRH19 B-19614-L Take-Up Plate AssemblyLH20 010.102 3-Bolt Flange Bearing1 in. Bore21 B-09859 Nip Point Guard (Specify OAW)22 BeltBlack Ultimate 140 (Specify Width)
Ref. No. Part No. Description23 U3 Clipper Unibar Belt Lacing (Specify Length)24 #13 Lacing Pin (Specify Length)25 B-13708 Snub Roller Guard (Specify OAW)26 B-13707 Snub Roller Guard Mounting Bracket27 B-13739 Snub Rlr. Guard Int . Dr. (Not Shown) (Spec. OAW)28 049.310 U-Type Speed Nut1/4-2029 MS Type Pivot Plate1-1/2 in. Flange B-00913 3-11/16 in. High B-02112 1-9/16 in. High30 Floor Support Frame
B-00914 6 in. High (Specify OAW) B-12777 7 in. High (Specify OAW) B-12778 8 in. High (Specify OAW) B-00915 9 in. High (Specify OAW) B-00916 11-1/2 in. High (Specify OAW) B-00917 14-1/2 in. High (Specify OAW) B-02098 18-1/2 in. High (Specify OAW) B-00919 22-1/2 in. High (Specify OAW) B-00921 32-1/2 in. High (Specify OAW) B-00923 44-1/2 in. High (Specify OAW) B-00925 56-1/2 in. High (Specify OAW) B-02107 68-1/2 in. High (Specify OAW) B-02109 78-1/2 in. High (Specify OAW) B-02111 90-1/2 in. High (Specify OAW)31 B-00911 Adjustable Foot Assembly (Speci fy Length)
-
8/13/2019 Manual Instalacion Cinta
30/36
30
4" Center Drive Assembly
Ensamble de la Unidad Motriz Central 4"
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description21 B-06093 Chain Guard Back Plate22 098.168 Spacer-13/32 in. I .D. x 1 in. O.D. x 1.539 in. Long23 040.31115 Hex Thin Head Bolt, 3/8-16 x 3-1/4 in. Long24 041.200 Hex Jam Nut, 3/8-1625 041.919 Acorn Nut3/8-1626 B-04842 11/16 in. Hex Idler Bracket27 B-17254 2-1/2 Dia. Heavy Duty Snub Idler (Speci fy BR)28 B-05477 Threaded Sect ion Spacer (Specify Drive Width)29 040.411 Take-Up Bolt1/2-13 x 9 in. Long
30 041.201 Hex Jam Nut1/2-1331 4 in. Dia. Take-Up Pulley B-22323 10 in. thru 18 in. Dr ive Width (Specify) B-05904 20 in. thru 34 in. Dr ive Width (Specify)32 010.102 3-Bolt Flange Bearing1 in. Bore33 B-05958 Take-Up Plate Assembly34 B-05966 Upper Bearing Guide35 B-04655 Bearing Guide Spacer36 B-04161 Bearing Guide37 B-04287 Rear Guard (Specify Drive Width)38 B-04286 Bottom Guard (Specify Drive Width)39 B-08337 Bottom Angle Guard (Specify Drive Width)40 B-08338-R Side GuardRH41 B-08338-L Side GuardLH42 B-08339 Formed Clip43 049.310 U-Type Speed Nut1/4-20
Ref. No. Part No. Description1 MotorC-Face 030.7134 1/2 HP230/460 VAC3 Ph.60 Hz.TEFC 030.7324 1 HP230/460 VAC3 Ph.60 Hz.TEFC2 Speed Reducer R-00153-30R 4ACRH30:1 Ratio R-00164-30R 5ACRH30:1 Ratio3 052.145 Coupling KitMotor to Reducer (1/2 - 1 HP)4 SprocketReducer 028.115 50B15 x 1 in. Bore (4AC)
028.117 50B15 x 1-1/4 in. Bore (5AC)5 028.123 SprocketDrive Pulley, 50B15 x 1-3/16 in. Bore6 029.101 #50 Riveted Roller Chain7 029.201 Connector Link#50 Roller Chain8 B-21330 4 Dia. Ctr. Drive Pulley (Ful ly Lagged) (Sp. Dr Wid.)9 B-06041 Drive Plate AssemblyRH10 B-06042 Drive Plate AssemblyLH11 010.103 3-Bolt Flange Bearing1-3/16 in. Bore12 090.203 Shaft Key1/4 in. Sq. x 1 in. Long13 B-11982 Motor Base Angle AssemblyRH Reducer14 B-11974 Motor Support AssemblyRH Reducer15 B-11977 Reinforcement Bar16 B-05965 Take-Up Bracket17 B-06629 Motor Base Assembly (Specify Dr ive Width)18 040.307 Take-Up Bolt3/8-16 x 2-1/4 in. Long19 041.300 Hex Jam NutHeavy3/8-1620 B-06090 Chain Guard Front Plate
-
8/13/2019 Manual Instalacion Cinta
31/36
8" Center Drive Assembly
Ensamble de la Unidad Motriz Central 8"
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description16 B-05965 Take-Up Bracket17 040.307 Take-Up Bolt3/8-16 x 2-1/4 in. Long18 041.300 Hex Jam NutHeavy-3/8-1619 B-05949 Chain Guard Assembly20 040.309 Hex Head Cap Screw3/8-16 x 3 in. Long21 041.919 Acorn Nut3/8-1622 B-04842 11/16 in. Hex Idler Bracket23 B-17254 2-1/2 Dia. Heavy Duty Snub Idler (Speci fy BR)24 B-03916 Bed Spacer (Specify Drive Width)25 040.411 Take-Up Bolt1/2-13 x 9 in. Long26 041.201 Hex Jam Nut1/2-1327 4 in. Dia. Take-Up Pulley B-22323 10 in. thru 18 in. Drive Width (Specify) B-05904 20 in. thru 42 in. Drive Width (Specify)28 010.102 3 Bolt Flange Bearing1 in. Bore29 B-05958 Take-Up Plate Assembly30 B-05966 Upper Bearing Guide31 B-04655 Bearing Guide Spacer32 B-04161 Bearing Guide33 B-08336 Rear Guard (Specify Drive Width)34 B-08335 Bottom Guard (Specify Drive Width)35 B-08337 Bottom Angle Guard (Speicfy Dr ive Width)36 B-08338-R Side Guard-RH37 B-08338-L Side Guard-LH38 B-08339 Formed Clip39 049.310 U-Type Speed Nut-1/4-20
Ref. No. Part No. Description1 Motor-C-Face 030.7134 1/2 HP230/460 VAC3 Ph.60 Hz.TEFC 030.7324 1 HP230/460 VAC3 Ph.60 Hz.TEFC 030.7534 2 HP230/460 VAC3 Ph.60 Hz.TEFC2 Speed Reducer R-00153-030R 4ACRH30:1 Ratio R-00164-030R 5ACRH30:1 Ratio3 Coupling Kit-Motor To Reducer 052.145 (1/2 1 HP) 052.146 (1-1/2 2 HP)4 Sprocket-Reducer 028.133 50B14 x 1 in. Bore (4AC) 028.1342 50B16 x 1-1/4 in. Bore (5AC)5 SprocketDrive Pulley, 028.13832 50B28 x 1-3/16 in. Bore (4AC) 028.1115 50B32 x 1-3/16 in. Bore (5AC)6 029.101 #50 Riveted Roller Chain7 029.201 Connector Link#50 Roller Chain8 B-02021 8 Dia. Ctr. Dr. Pul ley (Fully Lagged) (Sp. Dr. Width)9 B-05961 Drive Plate AssemblyRH10 B-05963 Drive Plate AssemblyLH11 010.202 4-Bolt Flange Bear ing1-3/16 in. Bore12 090.203 Shaft Key1/4 in. Sq. x 1 in. Long13 B-05946 Motor Base Support Angle Assembly14 B-05943 Motor Support Assembly15 B-06629 Motor Base Assembly (Specify Drive Width)
-
8/13/2019 Manual Instalacion Cinta
32/36
Model TR Power Feeder Parts Drawing
Dibujo de Partes del Alimentador Motriz TR
32
CONVEYOR WITH
CENTER DRIVEWITHOUT TAKE-UPS
(STANDARD)
CONVEYOR WITHEND DRIVE
WITH TAKE-UPS(OPTIONAL)
15 THRU 31 BED WIDTH
7 THRU 13 BED WIDTH
-
8/13/2019 Manual Instalacion Cinta
33/36
Model TR Power Feeder Parts List
Lista de Partes del Alimentador Motriz TR
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description1 Bed Weldment B-21401 18 in. Long 7 in. thru 13 in. BW (Specify) B-21399 33 in. Long 15 in. thru 21 in. BW (Specify) B-17134-025 48 in. Long 25 in. BW B-09516-031 60 in. Long 31 in. BW2 B-22222 4 in. Dia. Drive Feeder Pulley Assembly 8 in. thru 22 in. OAW (Specify)
3 B-22221 4 in. Dia. Tail Pulley Assembly 8 in. thru 32 in. OAW (Specify)4 010.102 3-Bolt Flange Bearing 1 in. Bore5 028.133 Sprocket 50B14 x 1 in. Bore6 090.203 Shaft Key1/4 in. Sq. x 1 in. Long7 029.101 #50 Riveted Roller Chain8 029.201 Connector Link#50 Roller Chain9 B-06168 Pivot Bracket
10 B-06174-001 Chain Guard11 040.3122 Hex Head Bolt, 3/8-16 x 4 in. Long12 041.919 Acorn Nut3/8-1613 B-09759-R Drive Plate AssemblyRH14 B-09759-L Drive Plate AssemblyLH15 Conveyor Take Up PlateRH B-19614-R (End Drive) B-09759-R (Center Drive)16 Conveyor Take Up PlateLH B-19614-L (End Drive) B-09759-L (Center Drive)17 B-09859 Nip Point Guard 8 in. thru 32 in. (Specify)18 Feeder Take-Up PlateRH B-19616-R 7 in. thru 21 in. BW (Specify) B-19614-R 25 in. and 31 in. BW (Specify)19 Feeder Take-Up PlateLH B-19616-L 7 in. thru 21 in. BW (Specify) B-19614-L 25 in. and 31 in. BW (Specify)20 B-19619 Attachment Plate Assembly (End Drive)21 041.919 Acorn Hex Nut3/8-1622 042.919 Shoulder Bolt1/2 in. x .312 Long23 B-02623 Gravity Bracket24 B-02624 Gravity Bar 12 in. thru 26 in. OAW (Specify)
Ref. No. Part No. Description25 B-02912 1 in. Dia. Pop-Out Rlr. 12 in. thru 32 in. OAW (Specify)26 091.110 Cable Assembly27 B-07987 Bearing Spacer28 B-06742 2-1/8 in. Dia. Snub Roller (Specify OAW)29 093.215 Return Roller Bracket30 B-14443 Snub Roller Guard 8 in. thru 14 in. OAW (Specify)
31 B-13708 Snub Roller Guard 8 in. thru 32 in. OAW (Specify)3 2 B - 1 3 7 0 7 Snub Roller Guard Mounting Bracket33 B-14445 Snub Roller Guard Mounting Bracket34 049.310 U-Type Speed Nut1/4-2035 040.407 Take-Up Bolt1/2-13 x 4 in. Long36 041.201 Hex Jam Nut1/2-1337 B-2057 Support Bar (Specify OAW)38 BeltBlack Ultimate 140 BOS (Specify Width)39 U3 Clipper Unibar Belt Lacing (Specify Length)40 #13 Lacing Pin (Specify Length)41 B-18909 Nip Point Guard 8 in. thru 32 in. OAW (Speci fy)42 MS Type Pivot Plate1-1/2 in. Flange B-00913 3-11/16 in. High B-02112 1-9/16 in. High43 Floor Support Frame B-00914 6 in. High (Specify OAW) B-12777 7 in. High (Specify OAW) B-12778 8 in. High (Specify OAW) B-00915 9 in. High (Specify OAW) B-00916 11-1/2 in. High (Specify OAW) B-00917 14-1/2 in. High (Specify OAW) B-02098 18-1/2 in. High (Specify OAW) B-00919 22-1/2 in. High (Specify OAW) B-00921 32-1/2 in. High (Specify OAW) B-00923 44-1/2 in. High (Specify OAW) B-00925 56-1/2 in. High (Specify OAW) B-02107 68-1/2 in. High (Specify OAW) B-02109 78-1/2 in. High (Specify OAW) B-02111 90-1/2 in. High (Specify OAW)44 B-00911 Adjustable Foot Assembly (Specify Length)
-
8/13/2019 Manual Instalacion Cinta
34/36
34
Underside Take-Up Assembly
Ensamble del Tensor Inferior
See Page 22 for Information on How To Order Replacement Parts
Recommended Spare Parts Highlighted In Gray
Vea la Pgina 23 para Informacin sobre Como Ordenar Partes de Repuesto
Partes de Repuesto Recomendadas se Resaltan en Gris
Ref. No. Part No. Description1 B-04842 11/16 in. Hex Idler Bracket2 4 in. Dia. Take-Up Pulley Assembly B-22323 10 in. thru 18 in. OAW (Specify) B-05904 20 in. thru 42 in. OAW (Specify)3 B-05477 Threaded Section Spacer (Specify BR)4 B-05966 Upper Bearing Guide5 B-07987 Bearing Spacer6 B-09844-R Side Channel AssemblyRH7 B-09844-L Side Channel AssemblyLH8 B-09848 Rear Guard (Specify OAW)9 B-09849 Bottom Guard (Specify OAW)10 B-09850 Bottom Angle Guard (Specify OAW)11 B-09851-R Side Belt GuardRH12 B-09851-L Side Belt GuardLH13 B-09852-R Take-Up Plate AssemblyRH14 B-09852-L Take-Up Plate AssemblyLH15 B-17254 2-1/2 in. Dia. Snub Roller (Specify BR)16 010.0021 Bear ing, Cast Iron, 2-Bolt, 1 in. Bore17 010.102 Bear ing, Cast Iron, 3-Bolt, 1 in. Bore18 040.411 Hex Bolt1/2-13 x 9 in. Lg.19 041.201 Hex Jam Nut1/2-1320 049.310 U-Type Speed Nut1/4-20
-
8/13/2019 Manual Instalacion Cinta
35/36
Notes
-
8/13/2019 Manual Instalacion Cinta
36/36
HYTROL CONVEYOR COMPANY, INC.2020 Hytrol Drive
Jonesboro, Arkansas 72401
Phone: (870) 935-3700
EFFECTIVE JUNE 2005Printed in the USA 6/05 by Master Printing
www.hytrol.com
top related