maxon ec motor...maxon ec motor 60 174 176–201 204–222 225–233 237–243 247–252 254–271...
Post on 06-Sep-2020
19 Views
Preview:
TRANSCRIPT
203
max
on
EC
mo
tor
60174
176–201204–222225–233237–243247–252254–271
maxon EC motor The electronically commutated EC motors are char-acterized especially by their favorable torque char-acteristics, high power, extremely broad speed range and, of course, by their unsurpassed service life.
Standard Specification No. 101Explanation of the EC motors
ECX ProgramEC ProgramEC-max ProgramEC-4pole ProgramEC-i ProgramEC flat Program
DC
Moto
r E
C M
oto
r(B
LDC
Mot
or)
Gearh
ead
Spin
dle
dri
veSenso
r M
oto
r
contr
ol
Com
pact
Dri
veA
ccess
ori
es
Cera
mic
C
onta
ct
info
rmati
on
max
on
EC
mo
tor
204
3 634700 3570023.4 12.1
13600 153000.215 0.2220.292 0.1540.367 0.4020.468 0.263
61 63
6.42 22.80.0231 0.08810.784 1.5312200 624099600 932001.16 1.08
0.00111 0.00111
M 5:2
129 K/W 2.78 K/W 0.13 s 78.0 s -20...+80°C +125°C
max. 0.06 mm 0.012 mm 0.1 N 10 N 0.2 N
1 3 1.2 g
431555 431558423518 423525
0 0.1 0.2 0.3 M [mNm]0.021 0.16 0.3 0.43 I [A]
0
10000
20000
30000
40000
50000
60000
423518
0.5 W
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 4 ∅4 mm, brushless, 0.5 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque mNm6 Nominal current A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data23 Max. speed 50 000 rpm24 Axial play at axial load 25 Radial play 26 Max. axial load (dynamic) 27 Max. force for press fits (static) 28 Max. radial load, 2 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection with hall sensors sensorless Pin 1 Motor winding 1 Motor winding 1 Pin 2 Motor winding 2 Motor winding 2 Pin 3 Motor winding 3 Motor winding 3 Pin 4 VHall 3.8...24 VDC N.C. Pin 5 GND Pin 6 Hall sensor 1 Pin 7 Hall sensor 2 Pin 8 Hall sensor 3 Connector Part number Part number MOLEX 52745-0897 52207-0460 FCI SFV8R-2STBE1HLF SFW4R-2STGE1LF Pin for design with Hall sensors: FPC, 8 pole, pitch 0.5 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅4 mm0.002 - 0.015 NmPage 308
Motor Data (provisional)
A with Hall sensorsB sensorless
Recommended Electronics:Notes Page 32
205205
max
on
EC
mo
tor
3 639800 2990077.6 24.8
22900 133000.319 0.3410.532 0.2090.774 0.6391.15 0.35856 56
2.6 16.70.00946 0.06680.671 1.7814200 536055200 503000.953 0.868
0.00165 0.00165
M 5:2
97.4 K/W 1.46 K/W 0.114 s 88.6 s -20...+80°C +125°C
max. 0.06 mm 0.012 mm 0.1 N 10 N 0.2 N
1 3 1.8 g
431182 431284414402 423511
0 0.2 0.4 M [mNm]0.057 0.36 0.67 I [A]
0
10000
20000
30000
40000
50000
60000
4144021.0 W
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36Planetary Gearhead∅4 mm0.002 - 0.015 NmPage 308
EC 4 ∅4 mm, brushless, 1.0 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient18 Thermal resistance winding-housing19 Thermal time constant winding20 Thermal time constant motor21 Ambient temperature22 Max. winding temperature
Mechanical data23 Max. speed 50 000 rpm24 Axial play at axial load25 Radial play26 Max. axial load (dynamic)27 Max. force for press fits (static)28 Max. radial load, 2 mm from flange
Other specifications29 Number of pole pairs30 Number of phases31 Weight of motor
Values listed in the table are nominal.
Connection with hall sensors sensorless Pin 1 Motor winding 1 Motor winding 1 Pin 2 Motor winding 2 Motor winding 2 Pin 3 Motor winding 3 Motor winding 3 Pin 4 VHall 3.8...24 VDC N.C. Pin 5 GND Pin 6 Hall sensor 1 Pin 7 Hall sensor 2 Pin 8 Hall sensor 3 Connector Part number Part number MOLEX 52745-0897 52207-0460 FCI SFV8R-2STBE1HLF SFW4R-2STGE1LF Pin for design with Hall sensors: FPC, 8 pole, pitch 0.5 mm, top contact style Wiring diagram for Hall sensors see page 41
Motor Data (provisional)
A with Hall sensorsB sensorless
Recommended Electronics:Notes Page 32
max
on
EC
mo
tor
206
455020 468897455019 468896
M 5:2
67.1 K/W 16.8 K/W 1.57 s 71.8 s -20...+100°C +125°C
< 0.15 N 0 mm > 0.15 N max. 0.06 mm
0.1 N 10 N 2 N
1 3 3 g
0 0.2 0.4 M [mNm]0.032 0.2 0.37 I [A]
0
20000
40000
60000
80000
100000455020
1.5 W
ESCON Module 24/2 426ESCON 36/3 EC 427 ESCON Mod. 50/4 EC-S 427DEC Module 24/2 430EPOS2 24/2 EC 434EPOS2 Module 36/2 434EPOS4 Mod./CB 24/1.5 441
6 1244200 3330046.5 16.2
25500 139000.334 0.3220.314 0.1160.832 0.590.688 0.188
56 50
8.72 63.80.0652 0.4361.21 3.147900 304057000 61800
4.2 4.550.00703 0.00703
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 6 ∅6 mm, brushless, 1.5 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 100 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) 28 Max. radial load, 2 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection with hall sensors sensorless Pin 1 Motor winding 1 Motor winding 1 Pin 2 Motor winding 2 Motor winding 2 Pin 3 Motor winding 3 Motor winding 3 Pin 4 VHall 3.8...24 VDC N.C. Pin 5 GND Pin 6 Hall sensor 1 Pin 7 Hall sensor 2 Pin 8 Hall sensor 3 Connector Part number Part number Molex 52745-0897 52207-0460 FCI SFV8R-2STBE1HLF SFW4R-2STGE1LF Pin for design with Hall sensors: FPC, 8 pole, pitch 0.5 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅6 mm0.002 - 0.03 NmPage 309
Motor Data (provisional)
A with Hall sensorsB sensorless
Spindle Drive∅6 mmPage 357–358
Encoder 6 MAG64–256 CPT,Page 391
For motor type B:Encoder 6 OPT128 CPT, Page 406
A with hall sensors B sensorless
Recommended Electronics:*Notes Page 32
* Not in combination with encoder 6 OPT. Adapter acc. to Overview on page 35.
207207
max
on
EC
mo
tor
455417 455418 455419455420 455421 455422
M 5:2
65.8 K/W 13.2 K/W 1.34 s 70.4 s -20...+100°C +125°C
< 0.15 N 0 mm > 0.15 N max. 0.06 mm
0.1 N 10 N 2 N
1 3 3 g
0 0.2 0.4 0.6 M [mNm]0.089 0.65 1.2 1.8 2.4 I [A]
0
20000
40000
60000
80000
100000
120000 2.0 W
455417
3 6 1274400 62700 63400
149 58.8 29.852300 44900 468000.413 0.412 0.4251.24 0.517 0.2681.45 1.52 1.73.92 1.72 0.9766 67 69
0.766 3.49 12.40.00529 0.0301 0.118
0.37 0.882 1.7525800 10800 546053400 42800 385003.93 3.15 2.84
0.00703 0.00703 0.00703
ESCON Module 24/2 426ESCON 36/3 EC 427 ESCON Mod. 50/4 EC-S 427DEC Module 24/2 430EPOS2 24/2 EC 434EPOS2 Module 36/2 434EPOS4 Mod./CB 24/1.5 441
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36Planetary Gearhead∅6 mm0.002 - 0.03 NmPage 309Spindle Drive∅6 mmPage 357–358
EC 6 ∅6 mm, brushless, 2 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 100 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) 28 Max. radial load, 2 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection with hall sensors sensorless Pin 1 Motor winding 1 Motor winding 1 Pin 2 Motor winding 2 Motor winding 2 Pin 3 Motor winding 3 Motor winding 3 Pin 4 VHall 3.8...24 VDC N.C. Pin 5 GND Pin 6 Hall sensor 1 Pin 7 Hall sensor 2 Pin 8 Hall sensor 3 Connector Part number Part number Molex 52745-0897 52207-0460 FCI SFV8R-2STBE1HLF SFW4R-2STGE1LF Pin for design with Hall sensors: FPC, 8 pole, pitch 0.5 mm, top contact style Wiring diagram for Hall sensors see page 41
Motor Data (provisional)
A with Hall sensorsB sensorless
Encoder 6 MAG64–256 CPT,Page 391
For motor type B:Encoder 6 OPT128 CPT, Page 406
A with hall sensors B sensorless
Recommended Electronics:*Notes Page 32
* Not in combination with encoder 6 OPT. Adapter acc. to Overview on page 35.
max
on
EC
mo
tor
208
6 12 2435900 43800 4270069.2 46 22.1
24000 32800 320000.977 0.942 0.9440.691 0.41 0.23.05 3.9 3.931.98 1.54 0.75567 69 70
3.02 7.8 31.80.039 0.106 0.4471.54 2.53 5.216200 3770 183012200 11600 112003.19 3.03 2.92
0.024961 0.024961 0.024961
M 5:2
468334
2.0 W
0.5 1.0
51.2 K/W 3.5 K/W 0.832 s 154 s -20…+100°C 125°C
< 0.15 N 0 mm > 0.15 N max. 0.06 mm
0.1 N 10 N 2 N
1 3 6 g
ESCON Module 24/2 426ESCON 36/3 EC 427 ESCON Mod. 50/4 EC-S 427DEC Module 24/2 430
468334 468335 468336468337 468338 468339
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 8 ∅8 mm, brushless, 2 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings) 23 Max. speed 80 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) 28 Max. radial load, 2 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection with hall sensors sensorless Pin 1 Motor winding 1 Motor winding 1 Pin 2 Motor winding 2 Motor winding 2 Pin 3 Motor winding 3 Motor winding 3 Pin 4 VHall 3.8...24 VDC N.C. Pin 5 GND Pin 6 Hall sensor 1 Pin 7 Hall sensor 2 Pin 8 Hall sensor 3 Connector Part number Part number Molex 52745-0897 52207-0460 FCI SFV8R-2STBE1HLF SFW4R-2STGE1LF Pin for design with Hall sensors: FPC, 8 pole, pitch 0.5 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅8 mm0.01 - 0.1 NmPage 310
Motor Data
Recommended Electronics:Notes Page 32
A with hall sensors B sensorless
A with Hall sensorsB sensorless
Spindle Drive∅8 mmPage 359–360
209209
max
on
EC
mo
tor
315170 315171 315172 315173315174 315175 315176 315177
6 9 12 1849200 52500 53200 57100
160 118 90.4 67.341700 45600 46600 509001.74 1.63 1.62 1.611.66 1.11 0.843 0.612 13 13.7 15.6
10.4 8.05 6.46 5.2777 78 78 79
0.575 1.12 1.86 3.420.00998 0.0198 0.0342 0.0671
1.15 1.61 2.12 2.978340 5920 4500 32204180 4110 3940 37003.03 2.97 2.85 2.68
0.0691 0.0691 0.0691 0.0691
M 1:1
8.0
20000
40000
60000
0.5 1.0 1.5 2.0
1.00.5 1.5 2.0
315170
1.5
39.8 K/W 5.1 K/W 1.51 s 221 s -40…+100°C +125°C
< 0.2 N 0 mm > 0.2 N max. 0.14 mm
0.16 N 12 N
250 N 2 N
1 3 13 g
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427 DEC Module 24/2 430
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 10 ∅10 mm, brushless, 8 Watt
Motor DataValues at nominal voltage
1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 65 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static)
(static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection with Hall sensors sensorless Pin 1 VHall 4.5…24 VDC Motor winding 1 Pin 2 Hall sensor 3 Motor winding 2 Pin 3 Hall sensor 1 Motor winding 3 Pin 4 Hall sensor 2 N.C. Pin 5 GND Pin 6 Motor winding 3 Pin 7 Motor winding 2 Pin 8 Motor winding 1 Adapter Part number Part number see p. 450 220300 220310 Connector Part number Part number Tyco 1-84953-1 84953-4 Molex 52207-1133 52207-0433 Molex 52089-1119 52089-0419 Pin for design with Hall sensors: FPC, 11-pol, Pitch 1.0 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅10 mm0.01 - 0.15 NmPage 312
Recommended Electronics:Notes Page 32
A with Hall sensorsB sensorless
max
on
EC
mo
tor
210
M 1:1
6.050000
10000
20000
30000
40000
0.5 1.0 1.5
1.0 2.0
416184
32 K/W 2.46 K/W 0.72 s 188 s -40…+100°C +155°C
< 1.8 N 0 mm > 1.8 N max. 0.05 mm
1.5 N 18 N 250 N 4 N
1 3 19 g
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427DEC Module 24/2 430
416184 430152 430153 430154 430155426333 430156 430157 430158 430159
6 9 12 18 2428800 30600 27500 27900 27700
168 121 78.6 53.5 39.820200 22700 19500 19700 194002.23 2.36 2.32 2.24 2.211.31 0.976 0.646 0.425 0.3127.79 9.53 8.27 8 7.724.08 3.52 2.06 1.35 0.97364 67 65 65 64
1.47 2.56 5.82 13.3 24.70.021 0.042 0.091 0.198 0.3571.91 2.71 4.01 5.92 7.945000 3520 2380 1610 12003850 3330 3460 3630 37407.83 6.76 7.02 7.38 7.590.194 0.194 0.194 0.194 0.194
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 13 ∅13 mm, brushless, 6 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 50 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor Values listed in the table are nominal.
Connection with Hall sensors sensorless Pin 1 VHall 4.5…24 VDC Motor winding 1 Pin 2 Hall sensor 3 Motor winding 2 Pin 3 Hall sensor 1 Motor winding 3 Pin 4 Hall sensor 2 N.C. Pin 5 GND Pin 6 Motor winding 3 Pin 7 Motor winding 2 Pin 8 Motor winding 1
Adapter Part number Part number see p. 450 220300 220310 Connector Part number Part number Tyco 1-84953-1 84953-4 Molex 52207-1133 52207-0433 Molex 52089-1119 52089-0419 Pin for design with Hall sensors: FPC, 11-pol, Pitch 1.0 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅13 mm0.2 - 0.35 NmPage 315
Motor Data
Recommended Electronics:Notes Page 32
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
211211
max
on
EC
mo
tor
426397 430160 430161 430162 430163 430164426576 430166 430167 430168 430169 430170
6 9 12 18 24 3624100 24200 24100 24900 24100 26600
198 132 98.9 68.9 49.5 38.218200 19100 18800 20000 19000 217005.15 5.64 5.13 5.53 5.18 5.382.37 1.72 1.18 0.871 0.598 0.45621.7 27.4 23.8 28.8 24.8 30.39.31 7.85 5.1 4.24 2.67 2.3874 76 75 77 75 77
0.644 1.15 2.35 4.24 9 15.10.0103 0.0233 0.0413 0.0879 0.165 0.308
2.33 3.49 4.66 6.8 9.32 12.74100 2730 2050 1410 1020 7511130 896 1030 877 990 8933.86 3.05 3.52 2.99 3.37 3.040.325 0.325 0.325 0.325 0.325 0.325
M 1:1
1250000
10000
20000
30000
40000
1.0 2.0 3.0
1.0 3.0
426397
6.0
23.9 K/W 1.26 K/W 0.603 s 263 s -40…+100°C +155°C
< 1.8 N 0 mm > 1.8 N max. 0.05 mm
1.5 N 18 N
250 N 4 N
1 3 29 g
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427ESCON Module 50/5 427ESCON 50/5 428DEC Module 24/2 430 DEC Module 50/5 430
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 13 ∅13 mm, brushless, 12 Watt
Motor DataValues at nominal voltage
1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient18 Thermal resistance winding-housing19 Thermal time constant winding20 Thermal time constant motor21 Ambient temperature22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 50 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic)27 Max. force for press fits (static)
(static, shaft supported)28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs30 Number of phases31 Weight of motor
Connection with Hall sensors sensorless Pin 1 VHall 4.5…24 VDC Motor winding 1 Pin 2 Hall sensor 3 Motor winding 2 Pin 3 Hall sensor 1 Motor winding 3 Pin 4 Hall sensor 2 N.C. Pin 5 GND Pin 6 Motor winding 3 Pin 7 Motor winding 2 Pin 8 Motor winding 1
Adapter Part number Part number see p. 450 220300 220310 Connector Part number Part number Tyco 1-84953-1 84953-4 Molex 52207-1133 52207-0433 Molex 52089-1119 52089-0419 Pin for design with Hall sensors: FPC, 11-pol, Pitch 1.0 mm, top contact style Wiring diagram for Hall sensors see page 41
Planetary Gearhead∅13 mm0.2 - 0.35 NmPage 315
Recommended Electronics:Notes Page 32
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
max
on
EC
mo
tor
212
12 18 24 36 4844500 42200 42800 45800 39600
397 241 185 139 80.839300 37400 38100 41100 348007.85 8.01 8.09 7.56 7.873.41 2.18 1.68 1.14 0.75475.5 78 82.7 82.3 72.529.8 19.4 15.6 11.1 6.3579 80 80 80 79
0.403 0.928 1.53 3.24 7.560.0235 0.059 0.102 0.2 0.477
2.54 4.02 5.29 7.4 11.43760 2380 1810 1290 836598 549 524 565 5544.54 4.17 3.98 4.29 4.210.725 0.725 0.725 0.725 0.725
M 1:1
3070000
15000
30000
50000
1.0
2.0 6.04.0
400160
3.02.0
.
16.3 K/W 1.68 K/W 1.97 s 240 s -20…+100°C +155°C
< 3.5 N 0 mm > 3.5 N max. 0.14 mm
3 N 35 N 250 N 10 N
1 3 34 g
400160 405812 400161 405813 400162404079 405817 404080 405818 404081
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427ESCON Module 50/5 427ESCON 50/5 428DEC Module 24/2, 50/5 430EPOS2 24/2, Module 36/2 434EPOS2 24/5, EPOS2 50/5 435EPOS2 P 24/5 438EPOS4 Mod./CB 24/1.5 441EPOS4 Module/CB 50/5 442MAXPOS 50/5 447
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 16 ∅16 mm, brushless, 30 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient18 Thermal resistance winding-housing19 Thermal time constant winding20 Thermal time constant motor21 Ambient temperature22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 70 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic)27 Max. force for press fits (static) (static, shaft supported)28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs30 Number of phases31 Weight of motor
Values listed in the table are nominal.
Connection A brown Motor winding 1 Pin 1 red Motor winding 2 Pin 2 orange Motor winding 3 Pin 3 yellow VHall 3…24 VDC Pin 4 green GND Pin 5 blue Hall sensor 1 Pin 6 violet Hall sensor 2 Pin 7 grey Hall sensor 3 Pin 8 Wiring diagram for Hall sensors see p. 41
Connection B (Cable AWG 24) brown Motor winding 1 red Motor winding 2 orange Motor winding 3
Motor Data
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
Connector: 8-pol 2.5 mm part number 478387 e.g. WCON WF2512-HXX
Planetary Gearhead∅16 mm0.1 - 0.6 NmPage 320/321
Recommended Electronics:Notes Page 32
for type A:Encoder MR128/256/512 CPT,Page 403
Planetary Gearhead∅22 mm0.5 - 1.0 NmPage 325Spindle Drive∅16 mmPage 361–363
213213
max
on
EC
mo
tor
M 1:1
6070000
15000
30000
50000
2.0 6.0
8 1612
394216
8.0
4 20
4.0
394216
10.3 K/W 1.2 K/W 2.53 s 299 s -20…+100°C 155°C
< 3.5 N 0 mm > 3.5 N max. 0.14 mm
3 N 35 N 250 N 10 N
1 3 58 g
394216 396916 395588 396928 405794397162 397294 397292 397295 405795
ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427ESCON Module 50/5 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 50/5 435EPOS2 70/10 435EPOS2 P 24/5 438EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443MAXPOS 50/5 447
12 18 24 32 4837100 43400 43400 43400 41700
327 272 204 153 96.232500 39200 39400 39500 3790017.2 16.9 17 17 17.15.82 4.48 3.39 2.54 1.63157 205 221 230 22451.4 52 42.2 32.8 20.585 86 87 87 87
0.233 0.346 0.569 0.976 2.340.02 0.033 0.059 0.104 0.2543.06 3.94 5.25 7 10.93120 2420 1820 1360 873238 213 197 190 1872.66 2.39 2.21 2.13 2.091.07 1.07 1.07 1.07 1.07
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 16 ∅16 mm, brushless, 60 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient18 Thermal resistance winding-housing19 Thermal time constant winding20 Thermal time constant motor21 Ambient temperature22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 70 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic)27 Max. force for press fits (static) (static, shaft supported)28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs30 Number of phases31 Weight of motor
Values listed in the table are nominal.
Connection A brown Motor winding 1 Pin 1 red Motor winding 2 Pin 2 orange Motor winding 3 Pin 3 yellow VHall 3…24 VDC Pin 4 green GND Pin 5 blue Hall sensor 1 Pin 6 violet Hall sensor 2 Pin 7 gray Hall sensor 3 Pin 8 Wiring diagram for Hall sensors see p. 41 Connection B (Cable AWG 24) brown Motor winding 1 red Motor winding 2 orange Motor winding 3
Motor Data
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
Recommended Electronics:Notes Page 32
for type A:Encoder MR128/256/512 CPT,Page 403
Planetary Gearhead∅22 mm0.5 - 1.0 NmPage 325
Spindle Drive∅16/22 mmPage 361–365
Planetary Gearhead∅22 mm0.5 - 2.0 NmPage 328
Planetary Gearhead∅16 mm0.2 - 0.6 NmPage 321
Connector: 8-pol 2.5 mm part number 478387 e.g. WCON WF2512-HXX
max
on
EC
mo
tor
214
386657 386658 386659 386660386661 386662 386663 386664
12 24 36 4830400 35200 31600 34200
238 144 83.3 69.326600 31800 28300 3090020.9 20.7 20.4 20.15.75 3.29 1.95 1.56184 243 221 23749.1 37.4 20.4 17.787 88 88 88
0.244 0.641 1.76 2.710.0182 0.0546 0.152 0.231
3.75 6.49 10.8 13.32550 1470 882 716166 145 144 1454.16 3.64 3.6 3.642.39 2.39 2.39 2.39
M 1:1
0 10 20 30 M [mNm]0.089 1.8 3.6 5.3 I [A]
0
10000
20000
30000
40000
50000
60000
70000 40386658
10 K/W 2 K/W 4.85 s 278 s -20…+100°C +155°C
< 4 N 0 mm > 4 N max. 0.14 mm
3.5 N 45 N 250 N 16 N
1 3 85 g
ESCON Module 24/2 426ESCON 36/3 EC 427ESCON Mod. 50/4 EC-S 427ESCON Module 50/5 427ESCON 50/5, 70/10 428DEC Module 24/2, 50/5 430EPOS2 24/2, Module 36/2 434EPOS2 24/5, 50/5, 70/10 435EPOS2 P 24/5 438EPOS4 Module/CB 50/5 442MAXPOS 50/5 447
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 22 ∅22 mm, brushless, 40 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 60 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection A brown Motor winding 1 Pin 1 red Motor winding 2 Pin 2 orange Motor winding 3 Pin 3 yellow VHall 3…24 VDC Pin 4 green GND Pin 5 blue Hall sensor 1 Pin 6 violet Hall sensor 2 Pin 7 grey Hall sensor 3 Pin 8 Wiring diagram for Hall sensors see p. 41
Connection B (Cable AWG 24) brown Motor winding 1 red Motor winding 2 orange Motor winding 3
Planetary Gearhead∅22 mm0.5 - 3.4 NmPage 328/329
Motor Data
Recommended Electronics:Notes Page 32
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
Spindle Drive∅22 mmPage 364/365
for type A:Encoder MR128/256/512 CPT,Page 403
for type B:Resolveron request
Connector: 8-pol 2.5 mm part number 478387 e.g. WCON WF2512-HXX
215215
max
on
EC
mo
tor
386673 386674 386675386676 386677 386678
18 24 4831000 29500 32100
373 257 14928200 27000 3000049.3 48.5 47.69.15 6.42 3.45644 691 857116 89.1 60.289 90 90
0.155 0.269 0.7970.0178 0.035 0.118
5.53 7.75 14.21730 1230 67248.3 42.8 37.62.07 1.83 1.614.09 4.09 4.09
M 1:1
100386673
0 20 40 60 80 M [mNm]0.13 4.2 8.3 12 17 I [A]
0
10000
20000
30000
40000
50000
60000
70000
7 K/W 1 K/W 4.92 s 355 s -20…+100°C 155°C
< 4 N 0 mm > 4 N max. 0.14 mm
3.5 N 40 N 250 N 16 N
1 3 128 g
ESCON Mod. 50/4 EC-S 427ESCON Module 50/5 427ESCON 50/5, 70/10 428DEC Module 50/5 430EPOS2 24/5, 50/5, 70/10 435EPOS2 P 24/5 438EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443EPOS4 Module 50/15 444EPOS4 Comp. 50/15 CAN 444MAXPOS 50/5 447
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 22 ∅22 mm, brushless, 100 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 60 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection A brown Motor winding 1 Pin 1 red Motor winding 2 Pin 2 orange Motor winding 3 Pin 3 yellow VHall 3…24 VDC Pin 4 green GND Pin 5 blue Hall sensor 1 Pin 6 violet Hall sensor 2 Pin 7 gray Hall sensor 3 Pin 8 Wiring diagram for Hall sensors see p. 41 Connection B (Cable AWG 24) brown Motor winding 1 red Motor winding 2 orange Motor winding 3
Planetary Gearhead∅22 mm0.5 - 3.4 NmPage 328/329
Motor Data
Recommended Electronics:Notes Page 32
A with Hall sensorsB sensorless
A with Hall sensors B sensorless
Spindle Drive∅22 mmPage 364/365
for type A:Encoder MR128/256/512 CPT,Page 403
for type B:Resolveron request
Connector: 8-pol 2.5 mm part number 478387 e.g. WCON WF2512-HXX
max
on
EC
mo
tor
216
M 1:1
25 100 150 20048 48 48 48
13300 13600 13800 1410063.9 53.4 54.9 56.5
11400 11700 12200 1320057.9 44 32.4 14.91.72 1.35 1.03 0.515460 346 295 25613.4 10.3 8.98 7.9387 86 85 84
3.59 4.64 5.35 6.050.626 0.626 0.626 0.62634.4 33.5 32.9 32.3278 285 290 29629 39.5 47.2 55.4
2.31 3.16 3.77 4.437.63 7.63 7.63 7.63
9.12 K/W 0.92 K/W 5.84 s 462 s -55…+200°C +240°C
< 5 N 0 mm > 5 N max. 0.14 mm
8 N 98 N 250 N 16 N
1 3 210 g
25000
20000
15000
10000
5000
10 20 30 40 50 60
120 W
80 W
40 W
20 W
M [mNm]
0.5 I [A]1.0 1.5 2.0
426448426449
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
EC 22 ∅22 mm, brushless, 80 WattHeavy Duty – for applications in air
Values at nominal voltage and ambient temperature °C1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed1) rpm5 Nominal torque (max. continuous torque)1) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed / torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
1) Values for operation in thermal equilibrium.
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 20 000 rpm24 Axial play at axial load 25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor (sensorless)
Connection A, motor cable PTFE (AWG 19) red Motor winding 1 black Motor winding 2 white Motor winding 3 Connection A, sensors cable PTFE (AWG 24) green VHall 4.5…24 V blue GND red Hall sensor 1 black Hall sensor 2 white Hall sensor 3 Connection B, motor cable PTFE (AWG 19) red Motor winding 1 black Motor winding 2 white Motor winding 3 Wiring diagram for Hall sensors see p. 41
Motor Data (provisional)
A with Hall sensorsB sensorless
Operating Range Comments
n [rpm] TA = 25°C
TA = 100°C
TA = 150°C
TA = 200°C
Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible winding temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
Application NoticeGeneral– extreme temperature applications– vibration tested (according to MIL-STD810F/Jan2000
Fig. 514.5C-10)– ultra-high vacuum applications (modifications necessary).
low outgassing, can be baked out at 240°CAerospace– gas turbine starter/generators for aircraft engines– regulation of combustion enginesOil & Gas Industry– oil, gas and geothermal wellsRobotics– robotic exploration vehiclesIndustry– pumps and valves for liquid metal cooling systems/turbine fuel
and steam control– valve adjustment for gas and steam power plants
This motor contains leaded solder. It therefore does not fulfill the requirements for the permitted maximum concentration of hazardous substances in accordance with the EC directive 2011/65/EC (RoHS) for all applications. The motor may there-fore only be used for devices that are not subject to this directive.
Specifications
max
on
EC
mo
tor
217217
426450426451
M 1:1
25 100 150 20048 48 48 48
12900 13400 13600 13800384 177 183 1888410 8510 9130 10600149 120 92.2 55.84.48 3.61 2.88 1.86460 346 295 25613.4 10.3 8.98 7.9371 77 75 73
3.59 4.64 5.35 6.050.626 0.626 0.626 0.62634.4 33.5 32.9 32.3278 285 290 29629 39.5 47.2 55.4
2.31 3.16 3.77 4.437.63 7.63 7.63 7.63
0.793 K/W 0.754 K/W 4.78 s 40.2 s -55…+200°C +240°C
< 5 N 0 mm > 5 N max. 0.14 mm
8 N 98 N 250 N 16 N
1 3 210 g
25000
20000
15000
10000
5000
20 40 60 80 100 120 M [mNm]
1.0 I [A]2.0 3.0 4.0
140
240 W200 W
140 W
80 W
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications
M 1:1
EC 22 ∅22 mm, brushless, 240 WattHeavy Duty – for applications in oil
Values at nominal voltage and ambient temperature °C1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed1) rpm5 Nominal torque (max. continuous torque)1) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed / torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
1) Values in thermal steady state.
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 20 000 rpm24 Axial play at axial load 25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor (sensorless)
Connection A, motor cable PTFE (AWG 19) red Motor winding 1 black Motor winding 2 white Motor winding 3 Connection A, sensors cable PTFE (AWG 24) green VHall 4.5…24 V blue GND red Hall sensor 1 black Hall sensor 2 white Hall sensor 3 Connection B, motor cable PTFE (AWG 19) red Motor winding 1 black Motor winding 2 white Motor winding 3 Wiring diagram for Hall sensors see p. 41
Motor Data (provisional)
A with Hall SensorsB sensorless
Operating Range Comments
n [rpm] TA = 25°C
TA = 100°C
TA = 150°C
TA = 200°C
Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible winding temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
Application NoticeGeneral– extreme temperature applications– vibration tested according to MIL-STD810F/Jan2000
Fig. 514.5C-10– operation in oil and high pressure (only minimal
lubrication, therefore use under rated ambient con-ditions is not suggested)
Oil & Gas Industry– oil, gas and geothermal wells
This motor contains leaded solder. It therefore does not fulfill the requirements for the permitted maximum concentration of hazardous substances in accordance with the EC direc-tive 2011/65/EC (RoHS) for all applications. The motor may therefore only be used for devices that are not subject to this directive.
Reference medium: Shell Tellus oil T15Operation in oil of different viscosity will affect the motor data.
Planetary Gearhead∅22 mm2.0 - 4.0 NmPage 330
maxon modular system Overview on page 28–36
max
on
EC
mo
tor
218
12 18 18 24 36 4815100 14300 13100 11000 14700 11300
662 404 349 199 211 10413400 12700 11500 9450 13200 974044.6 45.2 45.9 47.2 43.8 45.96.51 4.15 3.82 2.46 2.07 1.23428 443 407 355 454 35357.2 37.4 31.4 17.3 19.7 8.8480 81 81 80 81 80
0.21 0.481 0.573 1.39 1.83 5.430.03 0.0752 0.09 0.226 0.285 0.8567.48 11.8 13 20.5 23.1 401280 806 737 465 414 23935.8 32.7 32.6 31.5 32.8 32.57.49 6.86 6.82 6.59 6.87 6.820 20 20 20 20 20
M 1:2
5.4 K/W 2.5 K/W 14.8 s 1180 s -20…+100°C +125°C
< 8 N 0 mm > 8 N max. 0.14 mm
5.6 N 98 N 1200 N 28 N
1 3 270 g
ESCON 36/3 EC 427ESCON Mod. 50/5 427ESCON Mod. 50/4 EC-S 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 24/5, 50/5, 70/10 435EPOS2 P 24/5 438EPOS2 Module 36/2 434EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443MAXPOS 50/5 447
118891 118892 118888 118889 118893 118890
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 32 ∅32 mm, brushless, 80 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed1) 25 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection motor (Cable AWG 22) red Motor winding 1 black Motor winding 2 white Motor winding 3 Connection sensors (Cable AWG 26)1)
green VHall 4.5…24 VDC blue GND red/grey Hall sensor 1 black/grey Hall sensor 2 white/grey Hall sensor 3 Wiring diagram for Hall sensors see p. 41 1) Not lead through in combination with resolver.
Planetary Gearhead∅32 mm0.75 - 4.5 NmPage 334
Motor Data
Recommended Electronics:Notes Page 32
Planetary Gearhead∅32 mm0.75 - 6.0 NmPage 336–340
Encoder HED_5540500 CPT, 3 channelsPage 414/417Resolver Res 26∅26 mm10 VPage 422
Spindle Drive∅32 mmPage 366–368
219219
max
on
EC
mo
tor
15 24 42 489840 9840 10100 9840617 386 230 1939090 9120 9380 9150171 165 161 16512.2 7.39 4.24 3.692620 2660 2740 2760181 115 69.1 59.689 89 89 89
0.0829 0.209 0.608 0.8060.0329 0.0843 0.246 0.337
14.5 23.2 39.6 46.4659 412 241 2063.77 3.71 3.7 3.572.12 2.09 2.08 2.0153.8 53.8 53.8 53.8
M 1:2
369146
100 150 20050
5 15 2010
170 5.21 K/W 1.05 K/W 18.7 s 1910 s -40…+100°C +155°C
< 9 N 0 mm > 9 N max. 0.14 mm
23 N 106 N
5500 N 75 N
1 3 580 g
ESCON Mod. 50/5 427ESCON Mod. 50/4 EC-S 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 24/5, 50/5, 70/10 435EPOS2 P 24/5 438EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443EPOS4 Module 50/15 444EPOS4 Comp. 50/15 CAN 444MAXPOS 50/5 447
369146 393023 393024 393025
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 40 ∅40 mm, brushless, 170 Watt
Motor Data (provisional)Values at nominal voltage
1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data 17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 18 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static)
(static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor
Values listed in the table are nominal.
Connection motor (Cable AWG 16) red Motor winding 1 Pin 1 black Motor winding 2 Pin 2 white Motor winding 3 Pin 3 N.C. Pin 4 Connector Part number Molex 39-01-2040 Connection sensors (Cable AWG 26) yellow Hall sensor 1 Pin 1 brown Hall sensor 2 Pin 2 grey Hall sensor 3 Pin 3 blue GND Pin 4 green VHall 3…24 VDC Pin 5 N.C. Pin 6 Connector Part number Molex 430-25-0600 Wiring diagram for Hall sensors see p. 41
Planetary Gearhead∅42 mm3 - 15 NmPage 345Planetary Gearhead∅52 mm4 - 30 NmPage 350
Recommended Electronics:Notes Page 32
Encoder HED_5540500 CPT, 3 channelsPage 414/416Resolver Res 26∅26 mm10 VPage 422Brake AB 3224 VDC0.4 NmPage 460
max
on
EC
mo
tor
220
12 12 18 18 24 24 36 36 48 489780 5650 10300 5930 10500 6090 9360 5400 10200 58601530 577 1120 419 879 328 471 177 411 1548410 4370 9000 4680 9290 4840 8150 4190 8960 4640174 186 171 184 169 183 179 191 174 18716.2 9.65 11.2 6.72 8.55 5.13 5.29 3.14 4.21 2.521380 872 1540 931 1600 952 1560 911 1650 962119 43.6 93.3 32.6 74.8 25.6 43.1 14.5 37.2 12.579 79 80 79 80 79 81 80 81 80
0.101 0.275 0.193 0.552 0.321 0.936 0.836 2.48 1.29 3.850.0266 0.0797 0.0542 0.163 0.0917 0.275 0.263 0.788 0.395 1.19
11.5 20 16.5 28.6 21.4 37.1 36.3 62.8 44.5 77.1827 478 579 334 445 257 263 152 214 1247.22 6.58 6.78 6.46 6.67 6.49 6.07 6 6.22 6.188.99 8.19 8.44 8.05 8.32 8.08 7.56 7.48 7.75 7.7119 119 119 119 119 119 119 119 119 119
M 1:4
136204
1.9 K/W 0.9 K/W 15.4 s 1600 s -20…+100°C +125°C
1
< 20 N 0 mm > 20 N max. 0.14 mm
16 N 182 N 5000 N 140 N
1 3 850 g IP54*
ESCON 36/3 EC 427ESCON Mod. 50/5 427ESCON Mod. 50/4 EC-S 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 24/5, 50/5, 70/10 435EPOS2 P 24/5 438EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443EPOS4 Module 50/15 444EPOS4 Comp. 50/15 CAN 444 MAXPOS 50/5 447
136202 136196 136203 136197 136204 136198 136205 136200 136206 136201
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 45 ∅45 mm, brushless, 150 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 15 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor Protection to
Values listed in the table are nominal.
Connection motor (Cable AWG 16) Cable 1 Motor winding 1 Cable 2 Motor winding 2 Cable 3 Motor winding 3 Connection sensors (Cable AWG 24)1)
white Hall sensor 3 brown Hall sensor 2 green Hall sensor 1 yellow GND grey VHall 4.5 … 24 VDC Wiring diagram for Hall sensors see p. 41 1) Not lead through in combination with resolver.
* Protection level only when installed with flange-side seal.
Planetary Gearhead∅42 mm3 - 15 NmPage 345
Motor Data
Recommended Electronics:Notes Page 32
Planetary Gearhead∅52 mm4 - 30 NmPage 351
Encoder HEDL 9140500 CPT, 3 channelsPage 419Resolver Res 26∅26 mm10 VPage 422Brake AB 2824 VDC0.4 NmPage 459
221221
max
on
EC
mo
tor
136210 136207 136211 136208 136212 136209
24 24 36 36 48 488670 5000 10400 6010 10700 6160897 341 834 312 656 2447970 4300 9730 5320 10000 5490311 331 312 341 316 34712.5 7.51 10.2 6.21 7.94 4.864400 2540 5750 3320 6110 3530167 55.8 175 58.3 143 47.786 85 87 86 87 87
0.143 0.43 0.206 0.617 0.336 1.010.0565 0.17 0.0883 0.265 0.149 0.448
26.3 45.5 32.8 56.9 42.7 73.9364 210 291 168 224 1291.98 1.98 1.82 1.82 1.76 1.764.34 4.34 3.99 3.99 3.85 3.85209 209 209 209 209 209
M 1:4
136210
1.7 K/W 1.1 K/W 31 s 1570 s -20…+100°C +125°C
< 20 N 0 mm > 20 N max. 0.15 mm
16 N 182 N
5000 N 180 N
1 3 1150 g IP54*
ESCON Mod. 50/5 427ESCON Mod. 50/4 EC-S 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 50/5, 70/10 435EPOS4 Module/CB 50/5 442EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443EPOS4 Module 50/15 444EPOS4 Comp. 50/15 CAN 444MAXPOS 50/5 447
May 2017 edition / subject to change maxon EC motor
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 45 ∅45 mm, brushless, 250 Watt
Motor DataValues at nominal voltage
1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 12 000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static)
(static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor Protection to
Values listed in the table are nominal.
Connection motor (Cable AWG 16) Cable 1 Motor winding 1 Cable 2 Motor winding 2 Cable 3 Motor winding 3 Connection sensors (Cable AWG 24)1)
white Hall sensor 3 brown Hall sensor 2 green Hall sensor 1 yellow GND grey VHall 4.5…24 VDC Wiring diagram for Hall sensors see p. 41 1) Not lead through in combination with resolver.
* Protection level only when installed with flange-side seal.
Planetary Gearhead∅42 mm3 - 15 NmPage 345Planetary Gearhead∅52 mm4 - 30 NmPage 351
Recommended Electronics:Notes Page 32
Encoder HEDL 9140500 CPT, 3 channelsPage 419Resolver Res 26∅26 mm10 VPage 422Brake AB 2824 VDC0.4 NmPage 459
Planetary Gearhead∅62 mm8 - 50 NmPage 352
max
on
EC
mo
tor
222
M 1:4
167131
1.3 K/W 0.5 K/W 33.9 s 1200 s -20…+100°C +125°C
< 30 N 0 mm > 30 N max. 0.14 mm
24 N 392 N 6000 N 240 N
1 3 2450 g IP54*
ESCON Mod. 50/5 427ESCON Mod. 50/4 EC-S 427ESCON 50/5 428ESCON 70/10 428DEC Module 50/5 430EPOS2 50/5, 70/10 435EPOS4 Module 50/8 443EPOS4 Comp. 50/8 CAN 443EPOS4 Module 50/15 444EPOS4 Comp. 50/15 CAN 444 MAXPOS 50/5 447
167132 167131
48537067049607689.56
1180013987
0.3450.27384.9113
0.4573.98831
483100268
26808435.9
682046.486
1.030.8214765
0.4573.98831
maxon EC motor May 2017 edition / subject to change
Stock programStandard programSpecial program (on request)
Part Numbers
Specifications Operating Range Comments
n [rpm] Continuous operationIn observation of above listed thermal resistance (lines 17 and 18) the maximum permissible wind-ing temperature will be reached during continuous operation at 25°C ambient.= Thermal limit.
Short term operationThe motor may be briefly overloaded (recurring).
Assigned power rating
maxon Modular System Overview on page 28–36
EC 60 ∅60 mm, brushless, 400 Watt
Values at nominal voltage1 Nominal voltage V2 No load speed rpm3 No load current mA4 Nominal speed rpm5 Nominal torque (max. continuous torque) mNm6 Nominal current (max. continuous current) A7 Stall torque mNm8 Stall current A9 Max. efficiency %
Characteristics10 Terminal resistance phase to phase W11 Terminal inductance phase to phase mH12 Torque constant mNm/A13 Speed constant rpm/V14 Speed/torque gradient rpm/mNm15 Mechanical time constant ms16 Rotor inertia gcm2
Thermal data17 Thermal resistance housing-ambient 18 Thermal resistance winding-housing 19 Thermal time constant winding 20 Thermal time constant motor 21 Ambient temperature 22 Max. winding temperature
Mechanical data (preloaded ball bearings)23 Max. speed 7000 rpm24 Axial play at axial load
25 Radial play preloaded26 Max. axial load (dynamic) 27 Max. force for press fits (static) (static, shaft supported) 28 Max. radial load, 5 mm from flange
Other specifications29 Number of pole pairs 30 Number of phases 31 Weight of motor Protection to Values listed in the table are nominal. Connection motor (Cable AWG 16) Cable 1 Motor winding 1 Cable 2 Motor winding 2 Cable 3 Motor winding 3 Connection sensors (Cable AWG 24)1)
white Hall sensor 3 brown Hall sensor 2 green Hall sensor 1 yellow GND grey VHall 4.5 … 24 VDC blue Temperature sensor (PTC) pink Temperature sensor (PTC) 1) Not lead through in combination with resolver. Temperature monitoring, PTC resistance Micropille
110°C, R 25°C < 0.5 kW, R 105°C = 1.2…1.5 kW, R 115°C = 7…13 kW, R 120°C = 18…35 kW Wiring diagram for Hall sensors see p. 41
Planetary Gearhead∅81 mm20 - 120 NmPage 353
Motor Data
Recommended Electronics:Notes Page 32
Encoder HEDL 9140500 CPT, 3 channelsPage 419Resolver Res∅26 mm10 VPage 422Brake AB 4124 VDC2.0 NmPage 461
* Protection level only when installed with flange-side seal.
top related