miniature ball screws diameter 3 – 16 mm -...
Post on 22-Aug-2020
1 Views
Preview:
TRANSCRIPT
54
We l c o m e t o w h e r e p r e c i s i o n i s .
M i n i a t u r e B a l l S c r e w s D i a m e t e r 3 – 1 6 m m
3
We l c o m e t o w h e r e p r e c i s i o n i s .
Welcome to Steinmeyer!
4
We l c o m e t o w h e r e p r e c i s i o n i s .
H I S T O RY 1927 1942 1943
The Steinmeyer company was founded
by Mr. August Steinmeyer in 1920.
One year later, in 1921, he decided to
specialize in micrometers, which was
to become the product range for which
the small company was soon to be
recognized in the domestic market and
abroad.
When the founder suddenly passed
away in 1940, Mr. Erwin Beck assumed
leadership of the company, and
subsequently acquired it in 1950. The
house with its attached work shop, built
by the founder in 1937, became the
origin of a factory plant which occupies
some 8 acres of land today. The original
house still exists, but has since been
converted into offi ce and meeting space.
Beginning in the late 1960‘s, ball
screws have been manufactured at
the Albstadt factory. About 10 years
later, this new product line outgrew the
legacy micrometer manufacturing, and
the organization and production facility
had to be tailored towards the new
product line. The traditional micrometer
line, which still stands for precision and
reliability of Steinmeyer‘s products, is
now manufactured at the FMS Suhl plant
in Thuringia, an affi liated enterprise in the
Steinmeyer group.
5
© Bavaria Luftbild Verlag GmbH
The production plant in Albstadt. In the midst of the 35.000m² wide factory is the original building constructed by the foun-der. Together with the subsidiary companies in Suhl and Dresden the Steinmeyer-Group is a leading manufacturer of precision ball screws and precision measuring equipment.
Modern machine design places high demands on precision and reliability of its linear
drives. Ball screws, which have become an indispensable engineering element,
require a high degree of product knowledge. And Steinmeyer is your key partner for
development, production and application engineering.
Small screws specifi cally prove Steinmeyer‘s expertise. Still setting standards after 40
years, they have been developed to a degree of perfection second to none. Similarly,
machine tool design expects continuously improving performance and life fi gures from
its linear drives. Steinmeyer is committed to being at the cutting edge - always.
Such success is impossible without careful consideration of our customers‘
requirements, which requires continued dialog with them. Experienced staff and the
latest equipment ensure we stay at the top - which our customers have come to
expect.
In aerospace applications, precision has an additional signifi cance. It means applying
approved processes over and over again - with not the slightest deviation. From raw
material to the fi nished component to its maintenance during the entire life cycle, from
design and development to qualifi cation testing - everything must be done in a well
controlled environment and an absolutely repeatable manner. On the ground as well
as in the air.
O U R P H I L O S O P H Y
We l c o m e t o w h e r e p r e c i s i o n i s .
6
A R E A S O F A P P L I C AT I O N
Today ball screws are used in a widely
varying range of applications. Precision
ball screws from 20 to over 100 mm in
diameter are an indispensable element
for positioning and infeed applications
in today´s machinery and apparatus
construction.
The main challenge here is to provide
a dynamic and backlash-free power
transmission from rotational to linear
motion while keeping a high level of
stiffness and lifetime.
Miniature ball screws with diameters
of 16 mm and smaller are commonly
used for optical instruments, medical
engineering and other mechatronic
applications. Such applications require
the lowest possible friction.
Ball screws quite often have to survive
special environments such as Ultra High
Vacuum in electron microscopes or
high temperatures during sterilization of
surgical instruments.
Ultra Thrust ball screws not only require
bigger dimensions but also need special
design solutions e.g. for injection molding
machines or lifting tables.
Contrary to that there are applications
requiring very fi ne adjustment. Smallest
increments, e.g. in analysis devices, are
often achieved using precision ground
lead screws. Since screw shafts and
nuts are matched to “nearly backlash
free” they often perform better compared
to other drive types.
Applications in aerospace have quite
different demands on a ball screw. First
of all there is uncompromising reliability
under all imaginable operating conditions
while the precision issue takes a back
seat.
Of course design, manufacturing and
testing of aerospace ball screws has to
be continuously controlled to make sure
that failure is impossible.
7
We l c o m e t o w h e r e p r e c i s i o n i s .
8
T E C H N O L O G Y
M I N I AT U R E B A L L S C R E W S D I A M E T E R 3 - 1 6 M M
L A R G E B A L L S C R E W S D I A M E T E R 1 6 - 1 2 5 M M
U LT R A T H R U S T B A L L S C R E W S D I A M E T E R 5 0 – 1 6 0 M M
B A L L S C R E W S F O R A E R O S PA C E A P P L I C AT I O N S
R O TAT I N G N U T S
P R E C I S I O N L E A D S C R E W S
P R E C I S I O N AT A G L A N C E
This catalog contains the product range of Steinmeyer ball screws and is divided into
several product categories. Because it is not possible to show all special forms and
modifi cations please contact us to review your requirements. And please note that
nearly every other nut design, diameter / lead combination and ball size as well as
addi tional ball circuits are possible - as a custom unit. Please contact us for details.
We l c o m e t o w h e r e p r e c i s i o n i s .
10
Te c h n o l o g y
11
T E C H N I C A L I N F O R M AT I O N
PRECISION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 20
Lead accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 15
Friction torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 - 16
General geometric tolerances (acceptance criteria) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 - 19
Mounting tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 - 20
PRELOAD AND RIGIDITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 – 26 Nut designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 23
Rigidity - stiffness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 – 26
SERVICE LIFE CALCULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 - 30 Accounting for preload in the life calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 - 28
Duty cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 - 28
Equivalent load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 29
Fatigue life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 - 30
Load capacity according to ANSI standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 - 30
MAXIMUM LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 - 33 Buckling load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 - 32
Fracture load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 - 33
ROTATIONAL SPEED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 - 37 Critical speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 - 35
Maximum speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 36
DN value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 - 37
BEARING JOURNAL DESIGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 - 40 Pre-tensioning a ball screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 - 39
Select support bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 - 40
LUBRICATION AND WIPERS / SEALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 - 48 Tribology oil / grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 - 43
Oil lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 - 45
Grease lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 – 48
BALL RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 - 49
MATERIALS AND PROCESSES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - 50
DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 – 51
NUMBERING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 - 52
The following chapters only show a small portion of the wide fi eld of applications for ball screws. In order to meet all the technical
and commercial demands for such a wide variety of different tasks, a deep understanding of the technology of ball screws is ab-
solutely necessary. We have collected extensive information about ball screws in this section of this catalogue and hope that you
will fi nd it useful.
Please be aware that although we edited this information as carefully as possible, we cannot be held responsible for missing or
incorrect information.
12
P R E C I S I O N ( L E A D E R R O R , F R I C T I O N T O R Q U E , C R I T I C A L T O L E R A N C E S )
Under the headline „precision" DIN / ISO standards are explained as they apply to
ball screws, how accuracies are defi ned, and the acceptance or specifi cation criteria
derived from these standards.
Lead accuracy
Friction torque
Roundness, concentricity and squareness of relevant surfaces
In general, all acceptance criteria should be reviewed and agreed upon between Stein-
meyer and our customer. This is especially relevant for those applications where spe-
cial demands are required, for example a lead accuracy of class 5 but friction torque
variation consistent with accuracy class 1. In this example, Steinmeyer produces a
ball screw with economical class 5 lead accuracy but with much lower friction torque
variation.
Both DIN and ISO standards use the following terms and defi nitions to describe lead
accuracy. The corresponding JIS designations are given in parentheses:
Lead compensation c is used to compensate lead errors resulting from thermal
growth or pre-tensioning of the ball screw shaft (JIS: T).
The permissible lead deviation ep is an averaged lead error over the entire useful
travel (JIS: E)
The permissible lead fl uctuation vup
over the entire useful travel is defi ned as the
vertical distance of two straight lines parallel to the line representing ep which
enclose the entire lead error graph (JIS: e).
The lead fl uctuation v300p
represents the same for any 300 mm interval (JIS: e300
).
And fi nally the lead wobble v2πp
is the lead error within one revolution (JIS: e2π
).
Ball screws are normally categorized in accuracy classes, which not only defi ne lead
accuracy, but a number of different quality criteria like squareness and concentricity of
mating surfaces, shaft straightness, friction torque fl uctuation etc. Although this seems
to be a trouble-free approach, ball screw users often choose to specify these other
criteria by defi ning them in the source control drawing, while using ISO or DIN standard
accuracy classes to only describe lead accuracy.
Steinmeyer uses accuracy classes 1, 3, 5, 7 and 10 per ISO / DIN standard. Accura-
cy classes 0, 2 and 4 are not contained in these standards, but have been added to
match the JIS 1902 standard.
LEAD ACCURACY PER DIN 69051 / ISO 3408
Te c h n o l o g y
13
Limit ep for the average lead error e0a [μm]
lu [mm] Tolerance class
from to P0 P1 P2 P3 P4 P5 T7 T10
- 200 3 5 7 10 15 20
200 315 4 6 8 12 18 23
315 400 5 7 9 13 19 25
400 500 6 8 10 15 21 27
500 630 6 9 11 16 23 30
630 800 7 10 13 18 27 35
800 1000 8 11 15 21 31 40
1000 1250 9 13 18 24 35 46
1250 1600 11 15 21 29 42 54
1600 2000 - 18 25 35 50 65
2000 2500 - 22 30 41 59 77
2500 3150 - 26 36 50 72 93
3150 4000 - 32 44 62 88 115
4000 5000 - - - 76 108 140
5000 6300 - - - 92 131 170
devi
atio
n
travel
Lead error over the entire useful travel
Positioning ball screws PTransport ball screws T
The DIN standard differentiates between positioning ball screws and transport ball
screws.
Positioning ball screws are normally used in high-precision applications (like machine
tool) and are usually equipped with a ground ball thread.
Transport ball screws are predominantly used for travelling and moving applications.
Typical applications are axes for handling systems. Ball thread of such screws is
usually rolled or whirled.
Per DIN standard the tolerance classes for positioning ball screws are
described as "P" while the transport ball screws classes are described as "T".
Steinmeyer uses this designation as per DIN:
P0 – P5 for positioning ball screwsT5 – T10 for transport ball screws
The lead error ep is defi ned via a straight line, which represents the optimum approximation of the actual lead error graph. This
line will then be shifted parallel so it crosses the origin of the axis. This means that there can be a deviation at the beginning of
the travel. Also, the lead error at the end of travel can actually be greater than the maximum permissible error as long as the
average lies within the tolerance limits!
Nevertheless, a defi nition of the lead accuracy via ep is a stronger criteria than the commonly used deviation per 300 mm, be-
cause the error may not be accumulated. For example, the maximum permissible lead error ep of a screw 900 mm long is less
than three times the permissible error in 300 mm.
T E C H N I C A L T I P
lu300
ep = 2 . . V300p
14
Limits v300p for the fl uctuation v300a [μm]
Accuracy class
P0 P1 P2 P3 P4 P5 T7 T10
4 6 8 12 18 23 52 210
Lead error fl uctuation per 300 mm The variation over 300 mm is the most common defi nition. However it is also important
to know whether the allowed variation is cumulative, or not. If the allowable variation
is specifi ed as "cumulative" then the permitted error over the full travel of a screw can
result in a total error which is equivalent to the next lower accurancy class.
Example:
Stroke 900 mm, accuracy class P3, 3 x 300 mm would result in a total deviation of 3 x
12 μm = 36 μm. This result is equivalent to the total error of accuracy class P5 (35 μm)!
However, the admissible deviation ep for such a screw in accuracy class P3 is 21 μm.
Limits vup for the variation vua [μm]
lu [mm] Accuracy class [¹ n/a for rolled and whirled ball screws]
from to P0 P1 P2 P3 P4 P5 T7 T10
- 200 3 5 7 10 15 201 - -
200 315 4 6 8 12 18 231 - -
315 400 4 6 8 12 19 251 - -
400 500 4 7 8 13 20 261 - -
500 630 4 7 8 14 22 291 - -
630 800 5 8 9 16 24 311 - -
800 1000 6 9 10 17 26 351 - -
1000 1250 6 10 11 19 29 391 - -
1250 1600 7 11 13 22 33 441 - -
1600 2000 - 13 15 25 38 511 - -
2000 2500 - 15 18 29 44 591 - -
2500 3150 - 17 21 34 52 691 - -
3150 4000 - 21 25 41 62 821 - -
4000 5000 - - - 49 74 991 - -
5000 6300 - - - 58 88 1191 - -
Lead error fl uctuation over entire travel
The fl uctuation of the lead error is defi ned by two lines parallel to the line representing the average lead error, which include the
entire lead error graph.
The lead error fl uctuation is applicable to precision ground positioning screws in accuracy classes 0 - 5 only. It does not apply
to general purpose screws which are typically either rolled or whirled in classes 5 - 10.
T E C H N I C A L T I P
P R E C I S I O N
Te c h n o l o g y
15
The variation of the lead within one revolution, the so-called wobble-error usually is
sinusoidal. Here the DIN standard allows relatively coarse tolerances. If needed, this
tolerance can be restricted.
Ball screws are globally defi ned by the ISO standard 3408, which is compatible to DIN
69051 to a large extent. In Japan the JIS 1902 standard is valid while in the USA the
ANSI standard B92.1 is still occasionally used.
Concerning nut dimensions, the ISO standard has achieved acceptance, at least
where nuts are equipped with the space-saving internal defl ection system.
Quite often old data or specifi cations from other standards are used to defi ne a ball
screw. Therefore, please be cautious when trying to directly compare parameters such
as load capacity or stiffness.
While JIS and ISO standard are quite similar when describing accuracies or load capa-
cities, the ANSI standard is quite different, especially regarding load capacity.
Steinmeyer exclusively uses the ISO defi nitions.
travel
n.2πrad
devi
atio
n
v 2πp
v 2πa
Lead error fl uctuation over one revolution (lead wobble)
Limit v2πp for the lead error v2πa [μm] [¹ n/a to rolled or whirled ball screws]
Accuracy class
P0 P1 P2 P3 P4 P5 T7 T10
3 4 5 6 7 81 - -
16
The friction torque tolerance is solely defi ned for preloaded ball screws with double
nuts and is mainly affected by the accuracy class, preload value and diameter/length
ratio of a ball screw. The permissible torque fl uctuation is given in % based on the
nominal idling torque of a preloaded ball screw.
The values of the interclasses can be determined by interpolating.
TOLERANCE OF TORQUE
Variation of friction torque Friction torque
(nominal)
Friction torque variation in [%] For short screws (L ≤ 40 · dN)
For longer screws see table below!
Tpr0 [Ncm] Accuracy class
from to P0 P1 P3 P5 T7
5 10 40 45 50 60 -
10 20 35 40 45 50 -
20 40 30 35 40 50 -
40 60 25 30 35 40 -
60 100 20 25 30 35 40
100 250 15 20 25 30 35
250 630 10 15 20 25 30
630 1000 - - 15 20 30
Friction torque(nominal)
Friction torque variation in [%]For long screws (L ≥ 40 · dN)
Tpr0 [Ncm] Accuracy class
from to P0 P1 P3 P5 T7
5 10 - - - - -
10 20 50 50 60 60 -
20 40 40 40 50 60 -
40 60 35 35 40 45 -
60 100 30 30 35 40 45
100 250 25 25 30 35 40
250 630 20 20 25 30 35
630 1000 - - 20 25 35
travel
torq
ue
P R E C I S I O N
Steinmeyer can provide a friction torque chart for preloaded ball screws upon request (for an extra charge!). The test method
described in the ISO / DIN standard is to run the ball screw, with a thin fi lm of oil, at 100 rpm and without wipers. Other test
methods can be agreed upon. The values shown here apply to the test method per ISO / DIN standard.
Tolerances for the friction torque of preloaded single nuts are specifi ed individually.
Aerospace ball screws are often tested for idling torque, although they are normally not preloaded. This test serves to determine
proper operation of wipers and seals. This test can be part of the ATP; it is normally done with the ball nut greased and ready
for shipment.
T E C H N I C A L T I P
Te c h n o l o g y
17
The values listed below represent general rules for run-out tolerances of ball screws.
For specifi c applications tolerances may vary.
Steinmeyer recommends supporting the screw using the outside diameter for all ins-
pection of geometric tolerances. This will ensure optimum repeatability of the measu-
rement. In some cases the center holes are used as reference.
Tolerances of run-out and perpendicularity
GENERAL GEOMETRIC TOLERANCES (ACCEPTANCE CRITERIA)
AAA‘
AA‘ AA‘
AA‘
A‘
Run-out tolerances
A
l5
l5 l5
t5p
2 dN 2 dN
AA‘l5
l1
l5
A‘
Run-out Tolerance t5P
of the shaft outside diameter for the length l5 (the shaft straight-
ness with reference to AA') - according to DIN 69051 part 3 or ISO 3408-3.
Run-out tolerance t 5 P for the length l5 [μm]
dNAccuracy class
from to l5 P1 P3 P5 T7 T10
3 12 80
20 25 32 40 80
12 25 160
25 50 315
50 100 630
100 200 1250
Run-out tolerance t 5 max for the length l1 ≥ 4l5 [μm]
l1 / dNAccuracy class
from to P1 P3 P5 T7 T10
40 40 50 64 80 80
40 60 60 75 96 120 240
60 80 100 125 160 200 400
80 100 160 200 256 320 640
18
P R E C I S I O N
Run-out t3 [μm]
Nominal-∅ Accuracy class
dN [mm] P0 P1 P2 P3 P4 P5 T7 T10
3 - 6 3 4 6 7 8 10 - -
8 - 10 4 5 7 8 9 11 12 15
12 4 5 7 8 9 11 13 17
16 - 20 4 6 8 9 10 12 15 18
25 - 32 5 7 9 10 12 13 16 19
36 - 50 6 8 11 12 14 15 18 21
60 - 125 7 9 12 13 15 17 20 23
Run-out t3
Perpendicularity t4 [μm]
Nominal-∅ Accuracy class
dN [mm] P0 P1 P2 P3 P4 P5 T7 T10
3 - 6 2 2 2 3 3 3 - -
8 - 10 2 2 2 3 3 4 5 7
12 2 2 2 3 3 4 6 8
16 - 20 2 3 3 4 4 5 7 9
25 - 32 2 3 4 4 4 5 7 9
36 - 50 2 3 4 4 4 5 7 9
60 - 125 3 4 5 5 6 7 10 13
Perpendicularity t4
Run-out t2 Run-out t2 [μm]
Nominal-∅ Accuracy class
dN [mm] P0 P1 P2 P3 P4 P5 T7 T10
3 - 6 5 7 7 8 10 - - -
8 - 10 5 7 7 9 10 10 20 -
12 5 7 8 9 10 10 20 -
16 - 20 5 7 9 10 12 13 20 -
25 - 32 6 8 10 11 12 14 25 -
36 - 50 7 9 12 13 15 16 25 -
60 - 125 8 10 13 14 16 18 25 -
Te c h n o l o g y
19
Perpendicularity t5 [μm]
Nominal-∅ Accuracy class
dN [mm] P0 P1 P2 P3 P4 P5 T7 T10
3 - 6 6 7 8 9 9 10 - -
8 - 10 6 7 8 9 9 10 15 -
12 6 7 8 9 9 10 20 -
16 - 20 7 8 9 10 10 12 25 -
25 - 32 7 8 9 10 10 12 32 -
36 - 50 8 9 10 10 12 13 32 -
60 - 125 9 10 11 12 13 15 40 -
Perpendicularity t5
Run-out of pilot diameter t6 [μm]
Nominal-∅ Accuracy class
dN [mm] P0 P1 P2 P3 P4 P5 T7 T10
3 - 6 5 6 7 8 9 10 - -
8 - 10 5 6 7 8 9 10 20 -
12 5 6 7 8 9 10 20 -
16 - 20 5 6 7 8 9 10 20 -
25 - 32 5 6 7 8 9 10 20 -
36 - 50 6 7 8 8 10 11 25 -
60 - 125 7 8 9 10 12 13 32 -
Run-out t6
Steinmeyer‘s specifi ed parameters for concentricity and perpendicularity are
considerably lower compared to the DIN values.
Steinmeyer recommends supporting the screw by using V-blocks for all inspection of geometric tolerances. This will ensure
optimum repeatability of the measurement. If necessary, dual gages can be used to measure the concentricity of two surfaces
with respect to one another, e.g. the concentricity of drive journal and bearing journal. This measuring method includes the per-
pendicularity and run-out tolerance of the nut already.
T E C H N I C A L T I P
20
P R E C I S I O N
Perpendicularity
MOUNTING TOLERANCES
Parallelism
0.02 A - B P 1 - 50.03 A - B T 7 0.05 A - B T 10
A B
A B
0.02 A - B P 1 - 50.03 A - B T 7 0.05 A - B T 10
Steinmeyer recommends maintaining the mounting tolerances shown on this page. Optimum alignment of the screw with the
guideways and square and concentric mounting of the nut will ensure proper operation of the drive system and long life of the
ball screw.
After installation, check that the screw spins freely and without excessive friction over its entire travel. If there is any binding or
considerable increase in effort necessary to turn the screw, especially near the support bearings, this indicates the alignment of
the screw and the guideways should be improved. Binding indicates excessive side loads which can and will shorten the service
life of the ball screw unless corrected.
T E C H N I C A L T I P
Te c h n o l o g y
21
P R E L O A D A N D R I G I D I T Y
This section deals with the various nut types and their preload. We also explain the
different rigidity (stiffness) values.
Single nut with 4-point-contact Single nuts, as defi ned by Steinmeyer, are one-piece nuts without any shift or offset in
their I.D. ball thread. They can only be preloaded by ball oversize and will always have
4-point contact. This differentiates them from all other preloaded nuts and their 4 point
contact has an impact on technical data and some calculations.
4-point contact infl uences the kinematics of the balls with the following results:
Effi ciency of a single nut with preload is always somewhat lower than that
of a double nut
Single nuts with preload show a more pronounced reaction to manufacturing
tolerances, which is why they are normally not suitable for very long screws
Caution: these statements are only true for single nuts with preload. Without preload,
single nuts have 2-point contact with the same ball kinematics as double nuts!
Advantages of the single ball nut are:
Cost effectiveness
Compact envelope
No unloading of balls when subjected to peak loads (see preload chart)
NUT DESIGNS
Preload primarily serves to eliminate play. But at the same time preload increases rigidity, which means the displacement of the
nut under load is reduced.
Another reason why preload may be necessary is to prevent balls from skidding during high acceleration, or to ensure better load
distribution if side loads on the ball nut cannot be avoided.
There are a number of ways to preload a ball nut. For a discussion of preload and its effects we have to fi rst distinguish between
preload with two contact points per ball (one in the nut, one in the shaft), and preload with 4-point contact (two contact points
in the nut and two in the shaft), which requires the use of a „gothic arch" profi le.
Steinmeyer always uses a gothic arch profi le, so both kinds of preload are possible.
T E C H N I C A L T I P
We l c o m e t o w h e r e p r e c i s i o n i s .
22
Double nut (UNILOCK) Double nuts from Steinmeyer do not depend on the usual spacer ring or other hard-
ware to separate the two nuts. Our patented UNILOCK coupling ensures a robust
connection of the two nut halves. Thus Steinmeyer‘s double nut is almost as compact
and stiff as a single-piece design. Moreover, it prevents radial slippage of the two
halves, so the UNILOCK double nut cannot be misaligned by rough handling. The
coupling is rugged and absolutely tight to prevent loss of lubricant.
Advantages of a double nut are:
2-point contact for higher rigidity and effi ciency
Simplifi ed production compared to lead-offset nuts when the nut is long and helix
angles are large
Easier factory setting of preload without changing of balls, thus economical
Disadvantages are:
Longer nut body compared to single nuts, and somewhat higher cost
As in all nuts with 2-point contact, the maximum thrust should not exceed
2.8 times the preload
When preloading a UNILOCK double nut, the two halves are rotated relative to each
other until the balls are slightly compressed. Thus the threads of the second nut are
no longer directly „in phase" with the threads of the fi rst nut. There is a slight offset
between the two nut halves.
The lead offset nut uses the same principle but the offset is created during machining
of the threads in a nut made from a single piece of steel. Fine tuning of the preload is
then accomplished by selecting „oversized" balls like in a single nut. Due to the offset,
balls have 2-point contact.
Lead-offset nut
P R E L O A D A N D R I G I D I T Y
Steinmeyer labels all ball nuts that have 2-point ball contact a „double nut", regardless whether the nut body is made of two pie-
ces or one. This defi nition makes sense because both of these nuts have very similar properties, and because all life calculations
for these nuts are done in the same way. 4-point contact ball nuts on the other hand require different calculations, specifi cally
how preload is handled in the life calculations.
Steinmeyer‘s patented UNILOCK coupling of two-piece double nuts results in a connection that is nearly as stiff and compact as a
single-piece nut. This is why we do not distinguish between single-piece double nut design (the lead-offset nut) and a two-piece de-
sign (UNILOCK double nut) in this catalog. Steinmeyer will select whatever design is most suitable for the particular size of ball nut.All
nuts with 2-point contact can be recognized by the „5" in the 2nd number of their series designation (for example 1516, 3526 etc.).
T E C H N I C A L T I P
23
Advantage: Slightly more compact than a double nut (shorter length)
Disadvantage: More threads have to be machined from one end of the nut. Especially
in nuts with many turns and large helix angle, grinding I.D. threads can
be diffi cult or even impossible
NB: Steinmeyer often uses hard turning for such long nuts, eliminating the problems
associated with long and relatively weak grinding arbors.
Like the lead-offset nut, the pitch-offset nut uses a shift machined in the I.D. threads
to enable 2-point contact of balls. The only difference is that the pitch-offset nut uses
a two-start thread and the offset is between the two starts.
Each thread start has its own set of balls and ball returns.
Advantage: Pitch-offset nuts are extremely compact
Disadvantage: Pitch-offset preload can only be used in nuts with two (or more) starts
Pitch-offset nut
Almost exclusively used with miniature ball screws, the spring preload maintains perfectly
constant preload regardless of wear and manufacturing tolerances. Two nuts are installed
in a housing. One is fi xed, while the second one can slide longitudinally (a pin keeps it from
rotating). A spring located in between the two nuts keeps the preload constant.
The advantages are obvious:
Manufacturing tolerances will have no impact on preload and friction
Preload can be very light and the ball nut will never have play regardless of wear etc.
There are also some disadvantages:
The double nut with its housing is bulkier and more expensive
The slip-fi t of the second nut makes alignment more challenging
The maximum thrust is limited by the spring - when exceeded, the spring will
collapse causing play in the nut
Spring preloaded double nut
The spring preloaded nut excels when it is not possible to keep manufacturing tolerances low enough to ensure very low and
constant friction. This is the case when near zero friction is necessary while at the same time absolutely no play is acceptable,
or if the screw is extremely long.
Please be aware that the spring preloaded nut has a maximum operating force equal to about 2/3 of the preload. We can incre-
ase preload to some degree upon request, but if peak loads exceeding the preload force cannot be avoided, then a single nut
with rigid preload is preferred (miniature screw series 1112, 1214, 1412).
T E C H N I C A L T I P
24
STIFFNESS The rigidity of a ball screw not only has a strong impact on positioning accuracy, but
also plays an important role concerning the dynamic behavior of a linear drive. The
importance to the latter is normally underestimated.
Rigidity according to ISO 3408 or DIN 69051 is a value labeled Rb/t. This value is
obtained from theoretical elastic deformations obtained from the theory of Hertzian
pressure with the variables of track conformity, contact angle and the number of
load carrying balls. Rb/t is a relatively high number.
When the deformation of the nut body (diameter widening, longitudinal expansion) is
included, the value is labeled Rnu, and is already signifi cantly lower than Rb/t.
To obtain a real value, the theoretical vaule of Rnu has to be corrected further, since
not all balls carry the same load. Depending on the accuracy grade of the ball screw,
the correction factor varies. The reduced value, which is closer to reality and measu-
rable, is designated Rnu,ar.
Steinmeyer publishes only Rnu,ar values in our catalog and on our website. Please be
sure to compare these values only to similarly defi ned rigidities from other manufactur-
ers, and also ensure that the comparison is based on the same preload value you want
to use (see technical tip regarding the impact of preload on rigidity).
Besides number and size of loaded balls, track conformity and contact angle, the main
driver for the rigidity of the nut is preload. However, the possibility to signifi cantly increase
rigidity by raising preload is very limited because rigidity increases only as the cubic root
of preload. But the increase in heating is directly proportional plus the reduction of service
life is substantial since preload increase is raised to power three in the life equation.
This is why preload should not be set too high: For a nut with 2-point contact, 10% of the
dynamic load capacity is a reasonable number. Nuts with 4-point contact should not be
preloaded to more than approximately 8% of their dynamic capacity.
Steinmeyer publishes rigidity values for these preload settings:
10% Ca for nuts with 2-point contact (series x5xx)
8% Ca for nuts with 4-point contact (series x4xx)
Make sure when comparing with other manufacturer‘s rigidity data to check not only the
defi nition of terms but also that the comparison is done using the same preload.
Rigidity of the nut and preload
P R E L O A D A N D R I G I D I T Y
Higher preload results in in-
creased rigidity. But rigidity
increases only with the cubic
root of preload. To compare
stiffnesses based on different
preload settings, multiply rigi-
dity values by the cubic root
of the ratio of the preloads.
For example:
where Fpr1 and Fpr2 are the
preload settings to be com-
pared, and R1 and R2 are the
corresponding rigidities.
T E C H N I C A L T I P
Te c h n o l o g y
R2 = R1 · Fpr2
Fpr1
3
25
for better rigidity - static and dynamic
ball screws are not only signifi cantly more rigid in a classic sense, which only con-
siders the elastic deformation of a stationary screw under varying axial loads. They also
have a much better „dynamic stiffness", which means that the screw has a „linear beha-
vior" and delivers an axial movement perfectly proportional to its rotation, regardless of
thrust, speed and direction. Even reversing will not cause deviations from this.
This linearity is especially signifi cant in closed-loop controls, allowing considerably incre-
ased dynamics with substantially reduced following error. Unfortunately, this is not yet
refl ected in current ISO or DIN standards.
The screw stiffness depends on the elasticity modulus of the screw material, cross
sectional area of the screw and the unsupported screw length.
On fi xed-free bearing confi guration the screw stiffness is calculated as follows:
This is the calculation of the rigidity for fi xed-fi xed mounting method:
A: Screw cross section [mm2]
E: Young´s modulus [N/mm2]
(for DIN 1.1213 = 210,000 N/mm2)
Rigidity of the screw
Fixed-free mounting
Fixed-fi xed mounting
According to the ISO / DIN standard, the nut theoretical stiffness Rnu
is converted into the actual nut stiffness Rnu,ar
by applying a
correction factor which depends on the accuracy class of the ball screw. For example a ball screw with accuracy class 1 would
be more rigid than a screw of otherwise same design with an accuracy class 5. The reason for this is that better geometric tole-
rances of a more accurate screw, e.g. the lead wobble, result in more even ball loading.
Upon request (and extra cost), Steinmeyer will provide rigidity test protocols with every screw.
T E C H N I C A L T I P
Rs1 = A · ·10-3Els
Rs2 = 2 · A · ·10-3Els2
26
Elasticity of a linear drive includes elastic deformations of thrust bearings, ball screw
shaft and ball nut. This total, based on the „inverse" equation below, is what matters to
the performance of the drive. But only the nut stiffness is normally given in the technical
data of a ball screw.
Rt: Total rigidity [N/μm]
Rnu,ar
: Actual nut rigidity [N/μm]
Rs: Stiffness of the screw shaft [N/μm]
Rb: Axial stiffness of the thrust bearing [N/μm]
Total rigidity of a linear drive
The rigidity of the thrust bearing can be obtained from the literature of the manufac-
turer. Rigidity of the screw shaft can be calculated from the elasticity modulus of steel
(210,000 N/mm2), the shaft‘s cross section and the length of the loaded portion of the
shaft. For screws with large lead / diameter ratio, torsion also plays an important role
and must be considered as well.
If you want to do the calculation of axial and torsional stiffness yourself, just use the
nominal diameter of the ball screw minus the ball diameter to calculate the cross section
and moment of interia. Or, contact us and we will do this for you.
P R E L O A D A N D R I G I D I T Y
Installing thrust bearings at both ends of the screw yields four times the axial shaft stiffness compared to a single thrust bearing
at one end and no support on the opposite end. A factor of 2 results because forces are transmitted through the shaft on both
sides of the nut. A second factor of 2 also applies because the weakest point is now in the middle of the shaft rather than at the
extreme end.Thrust bearings at both ends normally require pre-tensioning the screw, against the support bearings, in order to
avoid compressive loads on the shaft from thermal expansion (which may cause buckling). Make sure to check the impact this
additional force has on the bearing life.
Linear drives with rotating nut and stationary screw allow a simple way of increasing torsional stiffness of the shaft by transmit-
ting moments into the surrounding structure at both ends of the shaft. Then the same effect as described above applies to the
torsional stiffness: A factor of 2 for twice the cross section, and again a factor of 2 for half the distance to the weakest point.
T E C H N I C A L T I P
Te c h n o l o g y
Rt = + +
Rnu,ar Rs Rb
1
1 1 1
27
Preload graph
ACCOUNTING FOR PRELOAD IN THE LIFE CALCULATION
Calculating modifi ed loads for nuts with 2-point-contact
S E R V I C E L I F E C A L C U L AT I O N S
Ball screws are normally loaded with axial forces. Service life is determined by material
fatigue in most cases. However, in some applications, abrasive or adhesive wear may
cause a loss of preload and thus be considered a failure of the ball screw.
In the ISO 3408 or DIN 69051 standards, the math used to estimate ball screw life is
based on material fatigue only. This is generally correct, but if the loading is very low
and mean speeds are very high, this method may return an erroneous life estimation
which cannot be reached in reality. If your application falls within this category, please
consult our engineers.
In this step, we modify axial forces to refl ect the impact of preload. The preload graph
shows how internal forces in the ball nut are affected by external forces and preload.
The preload graph includes two lines which represent the forces and resulting defor-
mation for both nut halves in a double (or pitch shift) nut. The center of the chart, where
the two lines cross, shows the situation of the nut with no external forces. Both nut
halves carry the same load - which is the preload Fpr.
If an external force is added, then the load in one nut increases, while it decreases in
the other. The resulting difference of the two forces is equal to the external load.
The load in each nut can be read from the two lines and this load is to be used for life
calculations. As a simple approximation, the nut with the higher load has to carry the
preload plus approximately half of the external load. Using this approximation for Fi* is
accurate enough.
As a quick and simple approximation for the internal load in nuts with 2-point contact,
just add or subtract half of the external thrust Fi to or from the preload Fpr. Whether
you call a certain thrust direction positive or negative does not matter. But you have
to keep this direction orientation the same for the whole duty cycle. The nut with the
highest load then determines service life.
Forc
e
Deflection Deflection
tens
ioni
ngnu
t
load
car
ryin
g nu
t
load
car
ryin
g nu
t
Forc
e
Tensioning nut Load carrying nut
Fi* : Modifi ed external load [N]
Fpr : Preload [N]
Fi : External load [N]
Fi*= Fi+Fpr 2
28
THE DUTY CYCLE AND ITS EQUIVALENT LOAD
To calculate the impact of actual duty on the fatigue life of the ball screw, it is necessary
to convert the varying loads Fi into a mean load F
m which will have the same effect on
life as the actual duty cycle. This mean load Fm is therefore called „equivalent" load.
To simplify things, the actual duty is normally divided into steps. Then the maximum
thrust (or, if the ball screw is preloaded, its modifi ed load), speed and duration are used
to calculate the equivalent load. Instead of using time and speed ni·q
i, the absolute
number of revolutions can be used in this calculation.
When calculating modifi ed loads for nuts with 4-point contact, all external thrust has to
be added regardless of load direction. The factor of 1.25 (5/4) is necessary to account
for the fact that the balls have 4 contact points, causing fatigue much sooner than in a
nut with 2 contact points. This approximation is accurate enough in cases with normal
loads and duty cycle.n
[rpm
]
The duty cycle of machine tools is normally provided as:
x1% Rapid with thrust y1
x2% Roughing with thrust y2
x3% Finishing with thrust y3
x4% Dwell
etc. Such values can be modifi ed to refl ect preload and then directly entered into the equation for Fm.
If the duty cycle provided includes a detailed description of moves, the respective revolutions can be entered instead of qi·ni
T E C H N I C A L T I P
Te c h n o l o g y
Calculating modifi ed loads for nuts with 4-point contact
5Fi*= Fi+Fpr4 2
29
EQUIVALENT LOAD
Fm : Permissible mean load for a given dynamic load capacity and life [N]
Ca : Dynamic load capacity required for a given mean load and life [N]
L10
: Fatigue life for a given dynamic load capacity and mean load [revolutions]
The mean or equivalent load is calculated using the above equation.
Fm : Dynamic equivalent load [N]
nm : Equivalent speed [rpm]
qi : Time percentage [%]
ni : Speed [rpm]
Fi : Thrust (which may need to be modifi ed - due to preload - fi rst) [N]
The service life estimate obtained from ISO / DIN calculations represents a dependa-
ble method to predict useful life of a ball screw under the conditions and for the duty
cycles found in most machines. Other necessary conditions include proper lubrication,
suitable protection from contamination, and operation of the ball screw at temperatu-
res not exceeding 70° C.
Should the calculated life fall outside the range mentioned on the following page, or if
there are special requirements or unusual conditions, please contact our application
engineers.
FATIGUE LIFE
Fm·Ca = L10
1063
Fm =Ca
L10
1063
Fm =q1 · n1 · F1 + q2 · n2 · F2 +…+ qn · nn · Fn
q1 · n1 + q2 · n2 +…+ qn · nn
33 3 3
n m =q1 · n1 + q2 · n2 +…+ qn · nn
q1 + q2 +…+ qn
T E C H N I C A L T I P
By defi nition, the dynamic load capacity is the load at which the ball screw will reach a useful life of 1 million revolutions.
More accurately, this means 90% of a suffi ciently large number of identical ball screws will reach this useful life. This life is de-
signated as L10
and is usually the basis for ball screw selection in normal machine design. For higher reliabilities than 90%, an
additional correction factor must be applied. In regular machine design, such higher reliabilities are normally not needed because
there are much greater uncertainties, for example in the estimate of thrust.
CaL10 ·106
Fm
3
=
30
The useful life L10 can be expected to be reached by 90% of a suffi ciently large number
of identical ball screws having a load capacity Ca, when subjected to the mean load Fm.
As an example, the life L5, which is 62% of L10, will be reached by 95% of the ball
screws. Aerospace applications require a more detailed reliability analysis, for which the
FMEA (Failure Mode and Effects Analysis) and fault trees are used to determine MTBF
(Mean Time Between Failure) or MTBUR (Mean Time Between Unscheduled Removal).
According to the ANSI standard, dynamic load capacity of a ball screw is the load un-
der which it will reach a life of 1 million inches of travel. If the lead is smaller than 1 inch,
then the load capacity per ANSI defi nition is smaller than the load capacity of the same
ball screw expressed according to ISO / DIN standard. This is because the ANSI load
capacity defi nes a load for which the resulting life in this case (lead less than 1 inch) is
greater than 1 million revolutions.
The opposite holds true for a ball screw with lead larger than 1 inch. For such a case,
the ANSI load capacity will be higher than the ISO load capacity, although the ball
screw itself is identical!
To compare load capacity of a ball screw per ANSI standard to one per ISO / DIN stan-
dard, a conversion must be made. This equation will also convert lbf into Newtons:
Ca : DIN / ISO-load capacity [N]
Pi: Load capacity per ANSI [lbf]
P: Lead [mm]
LOAD CAPACITY ACCORDING TO ANSI STANDARD
Reliability(probability of
survival)90 % 95 % 96 % 97 % 98 % 99 %
Correction factor 1 0.62 0.53 0.44 0.33 0.21
Calculation of the life expectancy is based, according to ISO / DIN standards, on Hertzian pressure. Theoretical load capacities
are then modifi ed with factors derived from experience. These corrected values allow very dependable predictions of ball screw
life, under normal conditions, if the calculated life expectancy falls within this range:
ANSI load capacity: According to ANSI ball screw standards, the dynamic load capacity is the load whereby the ball screw
reaches a life of 1 million inches of travel (ISO/DIN: 1 million revolutions). For a direct comparison with ISO/DIN numbers, the
ANSI load capacity must be converted as follows
T E C H N I C A L T I P
Preload is usually defi ned as a percentage of dynamic load capacity. Nuts with 4-point contact normally have a preload of 5 - 8%
of dynamic load capacity, while for nuts with 2-point contact it is 8 - 10%. Keep in mind this refers to ISO/ DIN load capacity only.
If the ANSI standard is used, then the percentages may change!
T E C H N I C A L T I P
Te c h n o l o g y
Ca= Pi · 4.45 · 25.4P
3
3 · 107 ≤ L10 ≤ 109[revolutions]
31
BUCKLING
There are fi ve ways a ball screw may fail due to overload:
Excessive dynamic loading, which means the screw makes too many revolutions
under a certain load resulting in material fatigue. This can be avoided by selecting a
ball screw with suffi cient dynamic load capacity (or by reducing the number of revo-
lutions and/or reducing the load). This is the subject of the load capacity discussion.
Exceeding the static load capacity, which causes instant and permanent damage to
the ball screw due to brinelling of balls and races, and prevents any further normal
operation of the ball screw. Static load capacities are listed as technical data.
Buckling of the shaft under compressive load. Buckling load value depends on be-
aring method and free length of the loaded ball screw shaft.
Failure of the nut body or of the bolts that connect it to the slide. This may happen
even before the static capacity is reached. Safe loads are discussed on the following
pages.
Radial loads. It means the load capacities given in this catalogue apply only to pure
axial loading. As there are always tolerances in the alignment of bearings and linear
guideways, there may be a small amount of radial force, which should be mini-
mized. Under normal conditions, a radial load less than 5% of the minimum axial
load will not cause any problems. When considering a ball screw for use under radial
load, please consult Steinmeyer engineers.
There are several analytical ways to demonstrate safety from buckling. In machine design,
the most frequently used is a simple calculation using formulas based on Euler equations.
Other, more accurate methods include non-linear FEM analysis and more involved
mathematics. These methods are normally used in aerospace applications, where
excess safety margins are not possible due to weight limitations. Please contact us if
you require such an analysis.
On the following page we describe a simple form of buckling analysis.
M A X I M U M L O A D ( L I M I T L O A D )
A reasonable load for a ballscrew, which may be sustained for signifi cant travel, is about 10% of its dynamic capacity.
A mean load of 10% of its dynamic capacity results in a theoretical life of 1 billion revolutions, which is the upper limit of the range
where the life equation is valid. Mean loads of a reasonably sized ball screw will therefore be somewhat higher than this, but
normally not exceed 20% of its dynamic capacity.
For short peak loads, the loading may be higher, but normally the loading of a ball nut with 2-point contact should not exceed
2.8 times the preload. And preload is around 5% - 10% of dynamic capacity.
As a rule of thumb, this all means the load range for a ball screw is really about 10% to 30% of its dynamic capacity.
T E C H N I C A L T I P
32
The following factors refer to the bearing me-
thods shown in the chart. Choose the appro-
priate one and use it as the variable m in the
equation to the left:B
uckl
ing
load
[kN
]
Length of unsupported shaft Is [mm]
Fixed - fi xed (1): 22.4
Fixed - supported (2): 11.2
Supported - supported (3): 5.6
Fixed - free (4): 1.4
Because of the logarithmic scale on the chart below, data for long screws or screws with large diameter may be diffi cult to read.
You may prefer to use this equation instead:
T E C H N I C A L T I P
Te c h n o l o g y
For safety reasons, a factor of 0.5 should be applied to the buckling load obtained.
PB: Buckling [N]
dN: Nominal-Ø [mm]
ls: unsupported screw length [mm]
m: bearing coeffi cient
4m · dNls
· 104PB 2=
Fmax = 0.5 · PB
33
[1] Flange 25 mm thick[2] Flange 30 mm thick
* Bolts DIN ISO 4762, Strength 8.8 (90% load, safety factor 0.8, μ = 0.14)
Please note: The highest permissible load is the minimum of static capacity C0a
(to prevent brinelling) and fracture load (to prevent
failure of ball nut or bolts). Necessary condition for both is proper alignment and squareness of the mounting surfaces and also
concentric applied load.
Additional limitations (e.g. buckling) may apply
Maximum loads for fl ange nut according to DIN 69051
Standardnut
UltraThrustnut
DIN 69051
Nominaldiameter
[mm]
DIN 69051bolt
pattern
Dynamic bolt tension Fb*
[kN]
Static bolt tension Fb*[kN]
Bolttorque[Nm]
Maximum permis-
sible axial load
[kN]
Maximum permis-
sible axial load
[ kN ]
5/6 4xM3 5 20 1.5 C0a 8 4xM3 5 20 1.5 C0a 10 4xM4 7 28 3 C0a 12 4xM4 7 28 3 7
16 6xM5 12 40 6 12 20 6xM6 16 63 10 16 25 6xM6 16 63 10 16 32 6xM8 32 100 25 32
40 8xM8 40 150 25 40 50 8xM10 80 225 49 80 120
60/63 8xM10 80 225 49 80 18080 8xM12 125 320 86 125 200100 8xM12 125 320 86 125 200-250100 8xM16 250 630 210 250 250125 8xM16 250 630 210 150¹ 300125 8xM16 250 630 210 250² 350
M A X I M U M L O A D ( L I M I T L O A D )
Some ball screws cannot be loaded all the way to their static capacity. Screws with high
dynamic load capacity (which might be selected to obtain a long enough service life at a
much lighter load) will necessarily have a high static capacity. But the term „static capacity"
is misleading, since the ball screw may actually fail due to fracture of the nut fl ange, nut
body, or connecting bolts before reaching this load!
FRACTURE LOAD
The structural strength of ball screws for aerospace applications is fi rst predicted using analytical methods including FEM analy-
sis. In some cases, tests are performed in the development phase to demonstrate safety and avoid costly and time consuming
redesigns once the qualifi cation phase of the project has started.
For the fi nal qualifi cation, tests under exactly the same conditions as in the aircraft must be passed. These tests often require test
rigs specifi c to the aircraft program, called „iron bird". The documentation of these tests becomes part of the aircraft qualifi cation.
In addition to static tests (limit load, ultimate load), fatigue tests are conducted. In these fatigue tests, an alternating or pulsating load
is applied to a ball screw that is not operating. This is not to be confused with endurance tests, which aim at fatigue also (to confi rm
dynamic load capacity), but with the pulsating load generated by balls running repetitively over the same spot of the ball track.
T E C H N I C A L T I P
34
Critical speed is the fi rst (lowest) speed at which the ball screw shaft is in resonance. In
applications with rotating shafts it limits the rpm of the screw. Variables that infl uence it
are shaft diameter, unsupported length and support bearing confi guration.
Similar to buckling, critical speed depends on the support bearing confi guration. Fixed
support bearings are assumed to resist angular defl ection of the shaft, while simple
support bearings do not. A bearing assembly consisting of two simple bearings with a
spacer would however qualify as "fi xed" bearing for the purpose here.
For long screws, we recommend using the following equation. Make sure to select the
proper factor for the bearing confi guration used:
nk: Critical Speed [rpm]
dN: Nominal diameter [mm]
ls: Unsupported length [mm]
k: Support bearing factor
R O TAT I O N A L S P E E D
Fixed - fi xed (1): 25.5
Fixed - supported (2): 17.7
Supported - supported (3): 11.5
Fixed - free (4): 3.9
Te c h n o l o g y
CRITICAL SPEED
The maximum nut speed should not be exceeded under any circumstances. There are, however, special executions available that
are suitable for higher speeds, so please inquire. Critical speed may be exceeded in certain cases - contact our application engineers
for further advice. And critical speed is not a signifi cant limitation in applications with rotating nuts. When operating at prolonged high
speeds, heating of the ball screw may become the limiting factor. Hollow screws for internal cooling are available, but this requires
an expensive additional system with its often troublesome rotating unions. Nuts with cooling jacket, which prevents heat migration
into the slide, have been tested but are not practical. Another possibile solution to running at high speeds for prolonged time is
Steinmeyer‘s technology. This advanced ball screw design produces less than half the heat compared to a regular ball screw
of same size. So steady-state temperatures remain much lower. This may eliminate the need to use a forced cooling system for the
ball screw shaft. Pre-tensioning amounts to compensate for thermal expansion are lower too, signifi cantly reducing the burden on the
support bearings from tensioning forces.
T E C H N I C A L T I P
nk = k · dN · · 1071ls
2
35
Crit
ical
spe
ed [r
pm]
Length of unsupported shaft Is [mm]
Critical speed is the fi rst resonant frequency (speed) of the rotating shaft. Resonance in a rotating shaft can be catastrophic and
even break the shaft. However, not all ball screws will necessarily exhibit such behavior since the nut represents another support
of the shaft, permanently changing the unsupported length of the shaft and its resonant frequency. Nevertheless Steinmeyer
recommends operating a ball screw only up to a maximum speed not to exceed approximately 80% of the critical speed, or to
discuss the possibility of higher speed with our engineers. For ball screws with rotating nuts, critical speed may be exceeded if
the run-out of the rotating nut is kept within tight tolerances. A perfectly concentric nut will not „pump" critical amounts of energy
into the shaft even if it is at or near its critical speed.
Pre-tensioning and critical speed: Contrary to general belief, pre-tensioning the ball screw shaft does not change the critical
frequency of the shaft. It is the stiffness against bending that resists centrifugal forces in a rotating shaft, not tension.
T E C H N I C A L T I P
36
MAXIMUM SPEED
Maximum speeds for UltraThrust ball screws diameter
50 - 125 mm [rpm]
Lead P 50 63 80 100 125
20 1600 1200 1000 800 650
25 1600 1200 1000 800 650
30 1600 1200 1000 800 650
40 1600 1200 1000 800 650
Maximum speeds nominal diameter 3 - 125 mm [rpm]
Lead P 3 5 6 8 10 12 16 20 25 28 32 36 40 50 60 63 80 100 125
0.5 4500 2900 2900 1800
1 4500 4500 4500 3000 2000 2000
1.5 4500 4500 3500 2500 2500
2 4500 4500 4500 3700 3700 2800 2200 1800
2.5 4500 4500 4000 4000 3500 4100 2500
3 4500 4500 4500 4500 4000 4100 3000
4 4500 4500 4500 4300 4100 3600 2800 2800
5 4500 4500 4500 4300 4100 3800 3800 3300 3300 2600 2100 1700 1200 1000 800
6 4500 4500 4500 4300 4100 3800 3800 3400 3400 3000 2200 1700 1200 1000 800
8 4500 4500 4500 4300 4100 3800 3800 3400 3400 3000 2400 1800 1200 1000 800
10 4500 4500 4300 4100 3800 3800 3400 3400 3000 2500 2000 1500 1200 1000
12 4500 4300 4100 3800 3800 3500 3500 3000 2500 2000 1500 1200 1000
15 4500 4300 4100 3800 3800 3600 3600 3000 2500 2000 1500 1200 1000
20 4500 4300 4100 4000 4000 4000 4000 3500 3000 2000 1500 1600 1000
25 4300 4100 4000 4000 4000 4000 4000 3000 2500 2000 2000 1600 1200
30 4300 4100 4000 4000 4000 4000 3500 3000 2500 2000 2000 1600 1200
35 3500 3000 2500 2000 2000 1600 1200
40 3500 3000 2500 2000 2000 1600 1200
A second limitation is imposed by the mass forces upon balls. It depends on internal
construction of the ball nut and in particular the ball return, and ball diameter (or mass).
The DN value does not take lead and ball size into consideration. In general, ball screws
with very small balls have somewhat lower speed limits than screws with larger balls.
We strongly recommend observing the speeds in the two tables below instead of DN
values.
R O TAT I O N A L S P E E D
Te c h n o l o g y
37
T E C H N I C A L T I P
DN values only yield a preliminary idea of the maximum speed, because there are more factors than just the nominal diameter
and the type of ball return that affect speed rating. Specifi cally the mass of balls plays an important role, which is not refl ected in
DN ratings. Also, the D
N method to determine maximum speeds is not applicable for very small screws.
DN VALUE The concept of DN is a simplifi ed way of determining the maximum rotational speed of
a ball screw. DN is simply the multiplication of nominal diameter of the ball screw in mm
times the maximum allowable speed in rpm. Keep in mind that for very small and very
large screws this will not return valid numbers.
DN values allow easy comparison between different ball screw designs. More sophis-
ticated ball return systems result in higher DN values and, conversely, lower D
N values
are associated with less sophisticated ball return methods. DN values provide direct
correlation to ball velocity.
nmax
: Maximum speed [rpm]
dN: Nominal diameter [mm]
DN: Driving speed value [mm/min]
Most ball screws available today have maximum DN values between 60,000 and
120,000, and in some cases even higher. However, Steinmeyer recommends obser-
ving the maximum speeds published here for each size. Use the following values for
orientation purposes and of course for Steinmeyer ball screws only:
Internal return (Series 1xxx): DN ≤ 120,000
External return (UltraSpeed and end-cap return) (Series 2xxx and 3xxx):
DN ≤ 160,000
High-load ball screws (UltraThrust)
(Series 3xxx with ball diameter 15 mm and 19 mm): DN ≤ 80,000
Always check the maximum speed tables.
When using only the DN me-
thod to determine maximum
rpm for a 3 mm ball screw,
the result would be 120.000
/ 3 = 40,000 rpm, which is
certainly not realistic. The DN
method returns unreasonab-
ly high numbers when used
for very small ball screws!
Always check the maximum
speed tables.
T E C H N I C A L T I P
DN = nmax · dN
38
B E A R I N G J O U R N A L D E S I G N A N D P R E - T E N S I O N I N G B A L L S C R E W S
Support bearings facilitate rotation of the shaft while transmitting axial loads from the
ball screw into the surrounding structure. They have to do that with minimum fric-
tion and the smallest possible deformation under changing loads. Modern ball screws
have high load capacity and rigidity, which places high demands on bearings as well.
Only high-end bearings which have been designed specifi cally for use with ball screws
can match the load capacity and rigidity numbers. Using inferior bearings yields unsa-
tisfactory results. It is also important that the interface between ball screw and support
bearings is designed properly.
A: The simplest journal design is a bearing seat that is small compared to the root dia-
meter of the ball thread. If the shoulder surface between the bearing journal diameter
and the root diameter (= nominal diameter - ball diameter) of the ball thread is suffi cient
to support the bearing preload plus the maximum thrust with reasonable surface pres-
sure, then this cost-effective solution is recommended.
B: Should the shoulder surface be too small, then the shaft could actually bend when
the locknut is tightened to preload the bearings. In this case, a full shoulder is needed,
that is the ball thread has to be incomplete instead of cutting through the shoulder -
sometimes referred to as a „dead start thread". This is possible for ground and whirled
screws, but impossible for rolled screws. Make sure that the other end of the ball th-
read is complete to allow mounting of the nut. Two incomplete ends of the ball thread
means costly complications of nut mounting!
C: If the shoulder surface is still insuffi cient, then a collar becomes necessary. Collars
can be heat shrunk onto the ball screw if there is still some difference between bearing
bore diameter and screw O.D. Shrunk collars are also possible for rolled screws. If
there is not enough shoulder for the shrunk collar to prevent axial slippage, then the
collar has to be solid, which means considerable machining time. This is the most
expensive solution.
Journal design
A
B
C
T E C H N I C A L T I P
If a long screw is to be pre-tensioned to compensate for thermal expansion, thrust bearings are required at both ends. One of
them needs to be adjustable to set exact tension of the shaft. A way to do that is by using a second locknut thread. Other pos-
sibilities include shims to set pre-tension. Always make sure to check elongation of the screw with a dial gage while tensioning it.
Suffi cient shoulder area is important, since creeping of the metal and loss of bearing preload results from excessive surface
loading. If the shoulder surface is not symmetric (for example when the thread cuts through it and the shoulder surface below
the root is insuffi cient to support the bearing), then cocking of the bearing will cause bending of the shaft with unsatisfactory
runout of the ball screw.
Te c h n o l o g y
39
The elongation of the shaft should at least be equal to the thermal expansion for the
anticipated steady-state temperature, or slightly larger.
Pre-tensioning requires considerable forces. In applications with rotating shaft, the
support bearings have to withstand these forces, which becomes a main considerati-
on for the selection of the bearings.
To calculate the tensioning force, assume that the root diameter of the screw is appro-
ximately the nominal diameter minus the ball diameter.
Calculating the elongation
Calculating the tensioning force
Δlp : Amount of elongation [mm]
ΔlT : Thermal expansion [mm]
FT : Tensioning Force [N]
E: Elasticity modulus [N/mm2]
A: Shaft cross section [mm2]
ε: Elongation relative to length
PRE-TENSIONING A BALL SCREW
Anticipating the temperature
The purpose to pre-tension a ball screw is to compensate for thermal expansion du-
ring operation and thus avoid compressive forces as the shaft expands between the
two fi xed bearings. The goal is to stretch the screw suffi ciently to maintain at least
some tension at the highest anticipated temperature.
T E C H N I C A L T I P
There is only a minimal change in the resonant frequency (critical speed) of the
shaft when tensioned. But tensioning is necessary when the screw is supported
by fi xed bearings at both ends. The fi xed bearings do of course result in raising
critical speed.
Ball screws may be ordered with a negative lead compensation c, so that after
tensioning the lead deviation is near zero.
Δt : Temperature rise [°C]
α : Coeff. of thermal expansion [1/°C]
(for DIN 1.1213 = 11.5 x 10-6
/ °C)
ls : Shaft length [mm]
Steinmeyer is capable of determining the steady-state temperature for your duty cycle.
Please contact us for details.∆lT = ls · ∆t · α
∆lp ≥ ∆lT
ε = ∆lp
ls
FT = E · A · ε
40
Support bearings must be able to carry not only the thrust produced by the ball screw,
but also any additional forces from pre-tensioning the ball screw shaft, plus any side forces
generated by belt drives. Ball nuts with many ball circles and/or large balls and shafts with
considerable pre-tension may make it diffi cult to fi nd bearings with suffi cient load capacity,
especially when the bore (ID) of the bearing has to be no larger than the shaft‘s root dia-
meter, and the journal shoulder diameter no larger than the ball screw‘s nominal diameter.
This discussion is only meant to highlight areas of concern. We cannot give detailed
recommendations on which bearing to select. Criteria for the selection include:
Axial dynamic load capacity of the bearing should be approximately equal to the
dynamic load capacity of the ball screw, or higher if the screw is pre-tensioned.
Minimum shoulder diameter for the bearing‘s inner ring should be no greater than
the root diameter of the ball screw (journal shape A), or no greater than the screw‘s
nominal diameter (journal shape B).
The bearing should be suitable for the same lubrication method (grease/oil) and
equipped with the proper seals for that lubricant. Speed ratings must be suffi cient
with the lubricant selected.
SELECTING SUPPORT BEARINGS
Steinmeyer recommends using INA support bearings. The following table gives ex-
amples of typical ballscrew / bearing assemblies. However, it is not possible to cover
all combinations in this catalog. Please refer to our engineering service for further
information.
B E A R I N G J O U R N A L D E S I G N
Te c h n o l o g y
Ballscrew nominal
diameter dN [mm]
INA-bearing with journal confi guration acc. to fi g.
A B C
16 ZKLN1034 - ZKLN1242
20 ZKLN1242 - ZKLN1545
25 ZKLN1747 - ZKLN2052
32 (P≤5) ZKLN2557 - -
32 (P>5) ZKLN2052 ZKLN2557 -
40 (P≤5) ZKLN3062 - -
40 (P>5) - ZARN3062LTN -
50 (P≤5) ZKLN4075 - -
50 (P>5) - ZARN4075LTN -
63 (P≤5) ZKLN5090 - -
63 (P>5) ZARN4090LTN ZARN45105LTN -
80 - ZARN50110LTN -
100 - ZARN60120LTN -
Miniature ball screws are
normally supported using
either a pair of angular
contact bearings on one
end, or by a single-row
bearing at both ends of the
screw, preloaded against
one another. It is better to
use bearings with increased
play here, since this will es-
tablish a more desirable con-
tact angle when the bearings
are preloaded. Bearings with
minimal or no play may ge-
nerate excessive forces on
their balls when preloaded
this way, causing potenti-
al premature bearing failure
and rough motion.
T E C H N I C A L T I P
This brief overview cannot give a fi nal selection aid to determinate an optimum bearing
solution. Radial loads due to drive belt tension or increased axial loads due to pre-
tensioning a ballscrew need to be considered, too.
41
L U B R I C AT I O N A N D W I P E R S / S E A L S
Supply of fresh lubricant and wipers must be considered together. The selection not
only depends on environmental conditions, but also on loads and speeds. In this sec-
tion we discuss whether grease or oil is the right lubricant, and which grease or oil
should be used.
Plastic wipers, sometimes called „labyrinth seals", are widely used in machine appli-
cations. They prevent contamination of the nut from chips and other larger particles,
while at the same time letting some oil exit the nut. Combined with automatic grease or
oil lubrication, they help to fl ush the nut. The result is higher reliability of the ball screw.
Felt wipers are an excellent solution for ball screws operated in an environment with
abrasive or otherwise troublesome dirt as in grinding or woodworking machines (for
example oil absorbing particles like wood chips). The felt wiper seals the nut effectively,
even from fi ne particles, and also stores some lubricant. Felt wipers are contact wipers
and add some friction.
Combination wipers are plastic wipers with an additional felt wiper (inside the ball nut).
They are used where felt wipers are desirable, but need to be protected from water or
water based fl uids. Felt tends to absorb water, so it should not be used without the
additional plastic wiper in such cases.
Combination wipers add to the nut length - please consult Steinmeyer for details.
Plastic Wiper
Felt Wiper
Combination Wiper
If the duty cycle is such that an EHD lubrication fi lm can build over a signifi cant part of the motion, then oil lubrication with a
properly selected oil grade and viscosity will always outperform grease in terms of wear. On the other hand, grease has an edge
at slow speeds because it offers better wear protection under mixed friction or boundary friction conditions. Grease can also be
used for long-term or for-life lubrication. Lubricant loss with grease is lower than with oil.
A general discussion for oil vs. grease lubrication and the results of a scientifi c test of several commonly used lubricants by the
tribology lab of CSEM at Neuchâtel/Switzerland (www.csem.ch ) is shown on the next pages.
T E C H N I C A L T I P
42
Results:
First of all, the coeffi cient of friction does not seem to be correlated to the wear rate.
Some lubricants yielded low friction, but higher wear at the same time!
The wear rates of some greases show that these lubricants can really be seen as
„universal", because they offer moderate wear protection at both slow and fast
speeds.
At the higher speed, both oils built a hydrodynamic lube fi lm, which can be conclu-
ded from the extremely low wear rates.
A plain mineral oil without wear-inhibiting additive (Vactra4) yielded excessive wear
rate at slow speed, despite its high viscosity. It was obviously unable to protect the
friction partners once speed fell below the threshold to build a hydrodynamic fi lm.
It was squeezed out of the contact patch and did not suffi ciently reduce wear in
boundary conditions.
Oil with high-pressure, wear inhibiting additives (EP oil), which is able to bond its
hydrocarbon molecules to metal surfaces through chemical or physical reaction,
performs much better during conditions of boundary friction.
With the exception of a high-pressure grease, which caused the lube fi lm to collapse at
high speeds, all greases performed well and yielded acceptable wear rates throughout
the test scenario. At the same time it was proven that greases are unable to build a
perfect fl uid fi lm like oils of proper viscosity, so the wear rate with grease lubrication is
higher than the wear rate of oil when an EHD fi lm is present.
C O M PA R AT I V E T E S T O F L U B R I C A N T S P E R F O R M E D AT C S E M / N E U C H Â T E L
TRIBILOGY OIL / GREASE On behalf of Steinmeyer and under the scope of a EUREKA project sponsored by the KTI
(Commission for Technological Interchange) in Switzerland, the tribology lab of CSEM
(Centre Suisse d‘Electronique et Microtechnique) designed and conducted a test for
commonly used lubricants under the specifi c tribological conditions found in ball screws.
A modifi ed pin-on-disc tribometer was used, with the pin replaced by a regular bearing
ball made from 52100 steel, which rode on a rotating disc made from the same material,
heat treated and ground similar to the raceway of a ball screw.
The disc and the ball closely resembled the friction partners in a ball nut in terms of
material and surface fi nish.
Surface loads and relative speeds in two test series were selected to simulate a slow
moving ball screw and a fast moving one. Since the pin-on-disc tribometer causes pure
sliding instead of the sliding/rolling typical for a ball screw, the speeds were adjusted to
the sliding portion of typical mid-size ball screw kinematics, running at about 50 rpm
(0,04 cm/s in the tribometer) and at approximately 1000 rpm (32 cm/s in the tribometer).
This simulated as closely as possible the real tribological conditions in a ball screw, both
in terms of lubrication fi lm build-up, and wear.
Te c h n o l o g y
43
Theory of elasto-hydrodynamic (EHD) lubrication
Life calculations for ball screws assume suffi cient lubrication, which means that there
is an adequate lubrication fi lm. In case of oil lubrication this means that whenever the
speed is suffi cient, a fl uid fi lm develops which separates the contact partners as much
as possible. This requires that
suffi cient oil is available at all times
contamination is minimal
lubricant is in adequate condition
viscosity is selected so that over most of the duty cycle a hydrodynamic lube fi lm is
maintained
The necessary condition to form such a fl uid fi lm is described by the theory of elasto-
hydrodynamic lubrication. Whether a fl uid fi lm, able to withstand the pressure in the
friction contact zone, will build depends on the actual viscosity of the lubricant and
the speed and, to a lesser extent, the pressure. However, a certain minimum load is
required (for example by preloading the ball screw) to cause a consistent rolling motion
of the balls.
Whether an EHD fi lm will build can be determined from the viscosity ratio k = u / u1.
The operational viscosity u is the viscosity the lubricant exhibits under the conditions in
the contact patch in terms of speed, temperature and pressure. The viscosity needed
to build a suffi cient EHD fi lm is u1.
The viscosity ratio can be classifi ed in 3 parts.
k ≥ 4 full EHD lubrication - contact partners are mostly separated
0.4 ≤ k < 4 mixed friction - lubricant with wear inhibiting additives is necessary, since
EHD fi lm is only partially able to separate contact partners (EP - grease, CLP - oil)
k < 0.4 no separation - accelerated wear through micro welding will occur
Since a high viscosity ratio is desirable, oil with high viscosity seems to be the solution.
But high oil viscosity also causes high temperatures, which in turn could lower the
actual viscosity again. High viscosity oil is also diffi cult to deliver to all lubrication points
and will not aid in cooling the ball nut.
We recommend using oil viscosities as close as possible to the ones per the following
table.
L U B R I C AT I O N A N D W I P E R S / S E A L S
44
OIL LUBRICATION Oil lubrication requires an oil port in the nut and wipers. Steinmeyer ships all ball screws
lubricated ready for use. If the screw is to be used with oil lubrication, please notify
us when ordering - we will then pack the nut with a special grease, which requires no
cleaning prior to use. The grease will be washed away with time and be dissolved in
the oil. The grease fi ll protects the screw during shipping and storage, and keeps it
lubricated until the oil supply is operational.
Oil should be injected approximately four times per hour. Recirculating oil systems
should include a fi lter with a 10 micron mesh and a cooler to keep the oil temperature
below 50° C as it enters the ball nut. Oil mist is only recommended when there are no
wipers and contamination is very low. Oil bath lubrication can only be used for very low
speeds. Oil drip and loss lubrication is possible, but oil quantities must be observed.
Only oils with wear inhibiting additives should be used. These have the ability to lubri-
cate in conditions of boundary friction, when speeds for EHD-lubrication are insuffi ci-
ent. We strongly recommend CLP grade gear oil per DIN 51517-3 or equivalent. Do
not use way oils or hydraulic oils, even if they are labeled „high pressure"!
Recommended oil quantities
Suitable oil grades
Nominaldiameter [mm]
Oil quantity in cm3/hr for oil circulation
Oil quantity in mm3/min for mini-
mum quantity lubri-cation (MQL) or oil
mist lubricationwithout extra
coolingwith extracooling
16 0.12 0.3 1
20 0.15 0.4 1.5
25 0.2 0.5 2
32 0.25 0.7 2.5
40 0.3 0.9 3
50 0.4 1.5 4
63 0.5 2 5.0
80 0.6 3.0 6.0
100 0.8 4.0 8.0
125 1.0 5.0 10.0
Te c h n o l o g y
45
Recommended oil viscosity for EHD lubrication
Nominaldiame-
ter[mm]
Meanspeed[rpm
Viscosityu1
[mm2/s]
Lubricanttemperature
[°C]
Viscositygrade ISO
VG
Actualviscosity u
[mm2/s]
up to 16 10 ca. 3000 30 680 ca. 3000
50 500 35 320 500
200 180 40 220 220
500 70 45 100 80
1000 40 50 68 42
2000 28 55 68 35
20 to 32 10 ca. 1200 30 460 ca. 1200
50 350 35 320 500
200 120 40 150 150
500 50 45 68 50
1.000 30 50 46 30
over 40 10 ca. 900 30 320 ca. 900
50 250 35 220 300
200 80 40 100 100
500 35 45 46 35
Felt or combination wipers seal the nut. It is therefore important, when using such wipers, that the recommended oil fl ow rates
are not exceeded. The nut may become overfi lled causing overheating at higher speeds.
Service life of oil lubricated ball screws exceeds the life that can be expected with grease lubrication in many cases, but only if
EHD lubrication can be reached over most of the duty cycle.
T E C H N I C A L T I P
46
Manual re-lubrication
Automatic grease lubrication
Re-lubrication of ball screws should be done with grease having the same, or compa-
tible, thickener as the grease used for factory lubrication. The base oil viscosity should
also be approximately the same. If not specifi ed otherwise, Steinmeyer uses Kluber
Staburags NBU 8 EP for factory grease fi ll of the nut. Please note that the factory
grease fi ll is only enough for initial operation, until the fi rst required re-lubrication.
Ball screws with regular plastic wipers should be re-greased every 500 hours of con-
tinuous operation, or four times a year. Ball screws with felt wipers have a recommen-
ded re-greasing interval of 1000 hours of operation, or twice a year.
If the ball screw is fi tted with felt or combination wipers and is adequately protected
from dirt and liquids (e.g. water, coolant), then the re-lubrication interval may be ex-
tended to 2000 hours or once a year. In such cases, Steinmeyer will pack the ball nut
with long-term grease Kluber Isofl ex NBU 15, and impregnate the felt wiper with an oil
compatible with this grease. Please consult with our application engineers if you want
your ball screw prepared for long-term lubrication.
There are two possible ways to automatically re-lubricate ball screws. Either the nut is
connected to an automatic lubrication pump with multiple ports, or a lubrication cart-
ridge is used. Both require a grease which is not too viscous and can be reliably pumped
through piping to its destination. Grease cartridges powered by chemical gas genera-
tors keep the grease pressurized all the time, which can cause the base oil to separate
from the thickener resulting in clogged lines and lubrication breakdown. We recommend
electromechanical cartridges, which use a gear motor and a lead screw to pump the
lubricant. These do not keep the grease under continuous pressure, thus preventing
such problems.
Normally, liquid greases NLGI class 0 or 00 are used for automatic grease lubrication,
because they can be pumped through long lines more easily. With large enough pipe
diameters, grease class 1 or even 2 can be used as well - but should fi rst be tested.
The intervals and quantities are shown on page 47.
GREASE LUBRICATION
Mineral oil based lubricants degrade with time in two ways:
They are attacked by aggressive chemicals (for example oxygen) from their environment, which causes a polymerization of the hy-
drocarbon or oxidation. The lubricant turns into a solid with time, but the process is slow in a normal environment, so re-lubrication
in normal intervals replaces the lubricant before it becomes too degraded. However, this chemical aging limits the storage period of
pre-greased components to 2 - 5 years. Specifi cs can be obtained from grease manufacturers.
During use, the hydrocarbon molecules are subjected to mechanical stresses when they are passed through the contact patches.
This mechanical stress causes the molecule chains to break up over time, reducing the viscosity. The maximum usage time of the
lubricant can be calculated - please contact us.
T E C H N I C A L T I P
Te c h n o l o g y
47
Nominaldiameter [mm]
Grease quantityon the shaft [g]
Grease quantity in the nut [g]
Single nut Double nut
3 0.15 - -
5 0.3 - -
8 0.7 - -
12 1 - -
16 4 0.2 0.3
20 7 0.5 0.8
25 10 0.7 1
32 17 1.1 1.7
40 25 1.8 2.7
50 35 2.4 3.6
63 50 3 4.5
80 70 4 6
Nominaldiameter [mm]
Grease quantity per shot [cm3]
Lube interval[h]
Single nut Double nut interval
16 0.01 0.03 4 - 8
20 0.03 0.06 4 - 8
25 0.03 0.06 4 - 8
32 0.06 0.1 4 - 8
40 0.06 0.1 4 - 8
50 0.1 0.16 4 - 8
63 0.16 0.2 4 - 8
80 0.2 0.3 4 - 8
Automatic re-lubrication
Manual re-lubrication
For non-aerospace applications, when re-lubricating manually using a grease gun, make sure not to pump more grease than
indicated in the table. Exceeding the recommended quantities will not only overfi ll the nut, but can actually pressurize it and push
the wipers out of their locations!
Ball screws for aerospace use are normally greased to a point where fresh grease appears either at both ends of the nut under-
neath the wipers or ice scrapers, or at a relief valve. Filling the nut completely is desirable in aerospace applications because the
grease keeps water from entering the nut. Due to the low average speeds of most aerospace actuator screws there is no risk
of overheating from excessive amounts of grease inside the nut, as would be the case in machine tools with their rapid motion.
T E C H N I C A L T I P
48
Recommended Grease
Application Kluber Low temp.
limit [C°]
Upper temp. limit
[C°]
Base oilviscosity[mm2/s]at 40°C
Lubcon Lowtemp.limit[°C]
Uppertemp.limit[°C]
Base oilviscosity[mm2/s]at 40°C
General purpose, long-term grease for high surface pressure
Staburags NBU 8 EP
-20 140 100 Turmogrease PHS 1002
-40 160 105
Long-term grease with felt wipers
Isofl ex NBU 15
-30 130 23 Turmogrease Highspeed L252
-50 120 25
Long-term grease without felt wipers, low speeds only
Stabu-rags NBU 12/300KP
-20 140 220 Turmogrease CAK 4002
-20 150 400
Low friction grease
Isofl ex LDS 18 Spezial A
-50 120 15 Thermoplex 2 TML Spezial
-70 130 20
High temperature grease
Klüberalpha BHR 53-402
-40 260 400 Turmotemp Super 2 EP
-30 280 500
Low temperature grease
Isofl ex PDL 300 A
-70 110 9 Thermoplex TTF 122
-70 150 12
Vacuum grease, clean room
Barrierta L55/2
-40 260 400 Turmotemp II/400 KL
Turmotemp II/400 RS2
-30
-30
260
260
400
550
Food grade grease
Klübersynth UH1 14-151
-45 120 150 Turmosynth-grease ALN 2501
-40 160 250
Te c h n o l o g y
Hybrid ball screws Hybrid design of ball screw means screw and nut are made from steel and balls are
made from ceramic.
Most suitable ceramic is Silicon Nitride in HIP-quality (not isostatic pressed).
Hybrid ball screws are designed to operate with very minimal lubrication. When ade-
quate lubrication is available there is no difference compared to conventional ball
screws equipped with steel balls.
The high hardness and Young´s modulus of Silicon Nitride (Si3N
4) results in a higher
applied load to the steel-ball race. Hybrid ball screws however must be assembled
using smaller steel spacer balls which means that only 50% of the balls are carrying
load. Therefore, the application of hybrid ball screws must be carefully reviewed.
49
The track-to-track return uses ball defl ectors to lift the balls across the O.D. of the
shaft and guide them directly into the next (or previous) track. Internal ball return is very
compact and yields the smallest nut diameters among all ball return systems. It is also
the ball return of choice for very small ball sizes and small leads.
Each defl ector serves one turn, which is one circuit (or ball circle).
Steinmeyer‘s „UltraSpeed" return is normally used for lead/diameter ratios greater than
0.5. It is normally used with dual start threads. Balls are lifted off the shaft using a
defl ector at one end of the nut and then guided through a bore (internal to the nut
body) to the other end of the nut, where a similar piece guides the balls back onto the
thread. One pair of defl ectors serves one circuit (i.e. one of the threads) which includes
several turns.
End cap return works very much like the previously described through-the-nut return,
with the exception that the ball defl ector function is executed using a (plastic) cap at
both ends of the ball nut. Each cap serves as the ball return and also includes wipers.
End cap return is normallly used for very large lead/diameter ratios. This style ball nut
is only available as a fl ange nut.
Track-to-track (internal return)
B A L L R E T U R N
Through-the-nut return (external return)
End cap return
Ball nuts require a means to recirculate balls. Without it, the ball path would not be closed and balls would fall out at the rear end
of the nut. Design of the ball return is the determining factor for the maximum speed at which the ball nut can safely operate.
This is normally expressed by the DN-value. The better the ball return system deals with mass forces of the balls, the higher the
DN value. Manufacturers typically quote D
N values from 60.000 for basic tube returns to 160.000 and higher, e.g. the UltraSpeed
return from Steinmeyer.
Steinmeyer uses all commonly known designs for ball returns. However, the multi-liner and the tube return are only used for
aerospace „build-to-print" applications, since staying with a previously qualifi ed design simplifi es the qualifi cation procedure.
T E C H N I C A L T I P
50
Materials
Application MaterialNo.
AMSdesigna-
tion
DIN / ISOdesignation
ANSIdesigna-
tion
Aero-spacegrade
Shaft 1.12131.20671.40211.41121.41081.41231.4125
AMS 5351AMS 7445DAMS 5898AMS 5925AMS 5618AMS 5844
Cf53100Cr6
X20Cr13X90CrMoV18
X30CrMoN15-1XD15W
X105CrMo17
105052100
440 B
440 CMP35N
••••
Generalpurpose
1.45451.4548
AMS 5659AMS 5643 X5CrNiCuNb17-4-4
15-5 PH17-4 PH
••
Nuts 1.20671.4108 AMS 5898
100Cr6X30CrMoN15-1 •
Balls 1.20671.41081.4125
AMS 5898AMS 5618
102Cr6X30CrMoN15-1X105CrMo17 440 C
••
Processes
SAEdesignation
AS 7003 / NADCAP certifi ed
Certifi edthrough 3rd party/custo-
mer audit
Externalprocess
AS 7102 Heat treatment • • •
AS 7114 Induction hardening • •
AS 7108 Chemical processes • •
AS 1701 NDT • •
AS 7117 Surface treatment • •
AS 7115 Elastomer Seals/Gaskets
• • •
AS 7200 Sealants • • •
AS 7101 Non-standard treatment • • •
M AT E R I A L S A N D P R O C E S S E S
Te c h n o l o g y
51
D E F I N I T I O N S
A: Shaft cross section [mm2]
α: Coeffi cient of thermal expansion [1/°C]
c: Lead compensation
C0a: Static axial load capacity [N]
Ca: Dynamic axial load capacity [N]
Caerf.: Required dynamic axial load capacity [N]
Δlb/t: Axial elastic deformation due
to external load Fi [μm]
Δlb/t,pr: Axial elastic deformation due to preload Fpr [μm]
Δlp: Elongation of the shaft [mm]
ΔlT: Thermal expansion [mm]
dN: Nominal diameter [mm]
DN: Driving speed value [mm/min]
Δt: Temperature increase [°C]
„E": Tolerance of the cumulative lead error (JIS)
E: Elasticity modulus [N/mm2]
ε: Elongation relative to length
e0a: Mean lead deviation over entire travel lue2π: Lead error in one revolution (JIS)
e300: Lead error in 300 mm (JIS)
ep: Tolerance for the average lead deviation
over entire travel luesa: Actual lead deviation over entire travel luFi: External load [N]
Fi*: Modifi ed external load [N]
Fm: Dynamic equivalent load [N]
Fm*: Modifi ed dynamic equivalent load [N]
Fpr: Preload [N]
FT: Tensioning force [N]
i: Number of ball circles
JIS: Japanese Industrial Standard
k: Support coeffi cient (critical speed)
L10: Nominal life 90% reliability [revolutions]
ls: Unsupported shaft length [mm]
lu: Travel [mm]
m: Support coeffi cient (buckling]
ni: Speed [rpm]
nk: Critical speed [rpm]
nm: Equivalent Speed [rpm]
nmax: Maximum Speed [rpm]
P: Lead [mm]
PB: Buckling load [N]
Pi: Load capacity per ANSI [lbf]
qi: Time percentage [%]
Rb: Axial bearing rigidity [N/μm]
Rnu,ar: Actual nut rigidity [N/μm]
Rs: Shaft rigidity [N/μm]
Rt: Rigidity of ball screw [N/μm]
T: Travel compensation (JIS)
Tpr: Preload torque
v2πa: Lead fl uctuation in one revolution
v300a: Lead fl uctuation in 300 mm
v300p: Tolerance of the lead fl uctuation in 300 mm
vua: Lead deviation over entire travel lu
vup: Tolerance of the lead deviation
over entire travel lu
52
B A L L S C R E W S 1 4 1 6 / 5 .40.800 .900 L P 3 P
1 nut with internal return
2 nut with end cap return
3 nut with external return
1 single nut with connection thread
2 cylindrical single nut
3 cylindrical double nut
4 fl ange single nut
5 fl ange double nut
1 single start thread, ground
2 dual start thread, ground
3 single start thread, rolled
4 dual start thread, rolled
5 single start thread, whirled
0 spring preloaded double nut
2 standard nut (Ø 3-16 mm)
4 customized nut
6 nut according to DIN 69051
lead (mm)
nominal diameter (mm)
thread length (mm)
overall length (mm)
E L lefthand thread
R stainless steel
P positioning ball screw
T transport ball screw
tolerance class
P preloaded nut
N U M B E R I N G S Y S T E M
Note:
This item number describes a ball screw with fl ange single nut acc. to DIN with in-
ternal return. Single start thread, ground. Lead 5 mm, nominal diameter 40 mm,
thread length = 800 mm, overall length = 900 mm, left hand thread, tolerance class P3,
preloaded nut.
Te c h n o l o g y
54
We l c o m e t o w h e r e p r e c i s i o n i s .
M i n i a t u r e B a l l S c r e w s D i a m e t e r 3 – 1 6 m m
55
M I N I AT U R E B A L L S C R E W S 3 – 1 6 M M
Miniature ball screws are mainly used in Semiconductor Technology, Optics, Medical Technology and Measurement Technology
markets. There are two different standard shaft styles available, style A and B, which are available in various stroke lengths. On
inquiry we offer suitable support bearings as well.
In addition to the standard ball screws, Steinmeyer also offers screws and nuts in completely custom execution. All sizes are
available in ground execution up to accuracy class P0. And from diameter 8 mm to 16 mm we also offer miniature rolled screws in
accuracy class T7 to T10.
Standard or Custom.
Whether you select a standard item from our extensive product range, or are looking for something specifi cally tailored to your
needs: Steinmeyer has a solution!
Our extensive list of standard screws is the right place to start collecting information. Even custom solutions may actually use the
same nut as a standard screw, so nut dimensions as well as technical data are the same.
We also manufacture ball screws entirely customized: unusual nut shapes, different pitches or diameters, special materials, special
coatings, etc. If that‘s what you are looking for, please contact us.
Our standard product range for miniature ball screws includes two different shaft versions, in various lengths, that can be com-
bined with four different nut designs. You may choose from a number of different diameters and leads, and several accuracy
classes. We have tried to present this variety as user-friendly as possible.
In addition to the different shaft lengths and travels, we supply ball screws with modifi cations such as reduced length or comple-
tely customized shafts. These non-standard shafts may be combined with one of the standard nuts shown here, or with custom
nuts. We will be pleased to quote whatever you require. Just send us a drawing or sketch.
T E C H N I C A L T I P
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
56
LFLF5
14
30°
D1 2215
30°
8
ØØ3,23,
DZ
LZ
LA
5
M6 DAA
N O M I N A L D I A M E T E R 3 m m Ground execution with standard bearing journal P0 - P5
Series 1412, 1214, 1112
F L A N G E N U T■ Series 1412: Nut with fl ange and standard wipers on
both ends
C Y L I N D R I C A L N U T■ Series 1214: Cylindrical nut without wipers
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1112: Nut with connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1412
/0,5
.3.7
6.9
0
1412
/0,5
.3.4
4.85
1412
/0,5
.3.6
4.10
5
1412
/0,5
.3.9
4.13
5
1412
/1.3
.76.
90
1412
/1.3
.44.
85
1412
/1.3
.64.
105
1412
/1.3
.94.
135
Shaft style A B B B A B B B
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1
Nominal diameter dN [mm] 3 3 3 3 3 3 3 3
Nominal stroke [mm] 50 20 40 70 50 20 40 70
Ball circles i 2 2 2 2 2 2 2 2
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8
Dynamic load capacity Ca [N] 90 90 90 90 240 240 240 240
Static load capacity C0a [N] 90 90 90 90 250 250 250 250
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
Max. friction torque [Ncm] (preloaded nut) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1)
Nut length LF / LZ / LA [mm] 15 15 15 15 15 15 15 15
Nut diameter D1g6 / DZh6 / DA [mm] 8 8 8 8 8 8 8 8
57
10 4
Overall length
Ø2h
6
Thread length
Ø2h
6
wrench flat 8
Ø3h
8 (4)
7 15, 5 7,5 7
3
Overall length
Ø4,
5h6
M6x
0,75
Ø6g
5
Ø9,
5
Thread length
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
P
1214
/0,5
.3.7
6.9
0
1214
/0,5
.3.4
4.85
1214
/0,5
.3.6
4.10
5
1214
/0,5
.3.9
4.13
5
1214
/1.3
.76.
90
1214
/1.3
.44.
85
1214
/1.3
.64.
105
1214
/1.3
.94.
135
1112
/0,5
.3.7
6.90
1112
/0,5
.3.4
4.85
1112
/0,5
.3.6
4.10
5
1112
/0,5
.3.9
4.13
5
1112
/1.3
.76.
90
1112
/1.3
.44.
85
1112
/1.3
.64.
105
1112
/1.3
.94.
135
A B B B A B B B A B B B A B B B
0.5 0.5 0.5 0.5 1 1 1 1 0.5 0.5 0.5 0.5 1 1 1 1
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
50 20 40 70 50 20 40 70 50 20 40 70 50 20 40 70
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8
90 90 90 90 240 240 240 240 90 90 90 90 240 240 240 240
90 90 90 90 250 250 250 250 90 90 90 90 250 250 250 250
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1) 0.3 (1)
7 7 7 7 7 7 7 7 15 15 15 15 15 15 15 15
7 7 7 7 7 7 7 7 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
58
5
LD
M6 DD
N O M I N A L D I A M E T E R 3 m m Ground execution with standard bearing journal P0 - P5
Series 1510
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1510: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1510
/0,5
.3.7
6.90
1510
/0,5
.3.4
4.85
1510
/0,5
.3.6
4.10
5
1510
/0,5
.3.9
4.13
5
1510
/1.3
.76.
90
1510
/1.3
.44.
85
1510
/1.3
.64.
105
1510
/1.3
.94.
135
Shaft style A B B B A B B B
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1
Nominal diameter dN [mm] 3 3 3 3 3 3 3 3
Nominal stroke [mm] 50 20 40 70 50 20 40 70
Ball circles i 2 2 2 2 2 2 2 2
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8
Dynamic load capacity Ca [N] 100 100 100 100 200 200 200 200
Static load capacity C0a [N] 200 200 200 200 300 300 300 300
Max. preload [N] 10 10 10 10 15 15 15 15
Max. axial load [N] 6 6 6 6 10 10 10 10
Friction torque Tpr0 [Ncm] 0.4-0.8 0.4-0.8 0.4-0.8 0.4-0.8 0.4-0.8 0.4-0.8 0.4-0.8 0.4-0.8
Nut length LD [mm] 23 23 23 23 23 23 23 23
Nut diameter DD [mm] 9 9 9 9 9 9 9 9
59
10 4
Overall length
Ø2h
6
Ø2h
6
Thread length
wrench flat 8
(4)
Ø3h
8
7 15,5 7,5 7
3
Overall length
Ø4,
5h6
M6x
0,75
Ø6g
5
Ø9,
5
Thread length
■ Shaft style A
■ Shaft style B
Please follow the advice on page 24/25.
P
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
60
LFLF6
D1
30°
2418
1616
30°
12
ØØ3,4
LF6
D1
30°
2418
16
30°
L3
12
ØØ3,43,
N O M I N A L D I A M E T E R 5 m m Ground execution with standard bearing journal P0 - P5
Series 1412, 2412, 1214
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1412: Nut with fl ange and standard wipers on
both ends
F L A N G E N U T■ Series 2412: Nut with fl ange and standard wipers on
both ends
LZ
DZ
C Y L I N D R I C A L N U T■ Series 1214: Cylindrical nut without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1412
/0,5
.5.9
0.11
0
1412
/0,5
.5.6
5.10
5
1412
/0,5
.5.1
25.1
65
1412
/1.5
.90.
110
1412
/1.5
.65.
105
1412
/1.5
.125
.165
1412
/1,5
.5.9
0.11
0
1412
/1,5
.5.1
25.1
65
Shaft style A B B A B B A B
Lead P [mm] 0.5 0.5 0.5 1 1 1 1.5 1.5
Nominal diameter dN [mm] 5 5 5 5 5 5 5 5
Nominal stroke [mm] 60 40 100 60 40 100 60 100
Ball circles i 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.6 0.6 0.6 0.8 0.8 0.8 1 1
Dynamic load capacity Ca [N] 170 170 170 490 490 490 640 640
Static load capacity C0a [N] 240 240 240 740 740 740 860 860
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5)
Nut length LF / LZ [mm] 22 22 22 21 21 21 23 23
Nut diameter D1g6 / DZh6 [mm] 12 12 12 12 12 12 12 12
L3 [mm] - - - - - - - -
61
14 6
Overall length
Ø3h
6
Ø3h
6
Thread length
wrench flat 8
Ø5h
8
(3) Thread length
Overall length
7,5
M6x
0,75
Ø4,
5h6
3
7 7 15,5
Ø9,
5
Ø6g
5 ■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
P
2412
/2.5
.90.
110
2412
/2.5
.65.
105
2412
/2.2
5.12
5.16
5
2412
/3.5
.90.
110
2412
/3.5
.65.
105
2412
/3.5
.125
.165
1214
/0,5
.5.9
0.11
0
1214
/0,5
.5.6
5.10
5
1214
/0,5
.5.1
25.1
65
1214
/1.5
.90.
110
1214
/1.5
.65.
105
1214
/1.5
.125
.165
1214
/1,5
.5.9
0.11
0
1214
/1,5
.5.6
5.10
5
1214
/1,5
.5.1
25.1
65
A B B A B B A B B A B B A B B
2 2 2 3 3 3 0.5 0.5 0.5 1 1 1 1.5 1.5 1.5
5 5 5 5 5 5 5 5 5 5 5 5 5 5 5
60 40 100 60 40 100 60 40 100 60 40 100 60 40 100
5 5 5 3 3 3 3 3 3 3 3 3 3 3 3
1 1 1 1 1 1 0.6 0.6 0.6 0.8 0.8 0.8 1 1 1
990 990 990 590 590 590 170 170 170 490 490 490 640 640 640
1490 1490 1490 820 820 820 240 240 240 740 740 740 860 860 860
0.02 0.02 0.02 0.02 0.02 0.02 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.02 0.02
0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5)
11 11 11 11 11 11 13 13 13 12 12 12 14 14 14
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
5 5 5 5 5 5 - - - - - - - - -
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
62
6LA
M10x1
for pin wrench Ø2
DAA
LD6
M10x1 DD
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1510: Spring preloaded double nut in housing with
connecting thread without wipers
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1112: Nut with connecting thread without wipers
N O M I N A L D I A M E T E R 5 m m Ground execution with standard bearing journal P0 - P5
Series 1112, 1510
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1112
/0,5
.5.9
0.11
0
1112
/0,5
.5.6
5.10
5
1112
/0,5
.5.1
25.1
65
1112
/1.5
.90.
110
1112
/1.5
.65.
105
1112
/1.5
.125
.165
1112
/1,5
.5.9
0.11
0
1112
/1,5
.5.6
5.10
5
1112
/1,5
.5.1
25.1
65
Shaft style A B B A B B A B B
Lead P [mm] 0.5 0.5 0.5 1 1 1 1.5 1.5 1.5
Nominal diameter dN [mm] 5 5 5 5 5 5 5 5 5
Nominal stroke [mm] 60 40 100 60 40 100 60 40 100
Ball circles i 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.6 0.6 0.6 0.8 0.8 0.8 1 1 1
Dynamic load capacity Ca [N] 170 170 170 490 490 490 640 640 640
Static load capacity C0a [N] 240 240 240 740 740 740 860 860 860
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5) 0.4 (1.5)
Max. preload [N] - - - - - - - - -
Max. axial load [N] - - - - - - - - -
Friction torque Tpr0 [Ncm] - - - - - - - - -
Nut length LA / LD [mm] 19 19 19 18 18 18 20 20 20
Nut diameter DA / DD [mm] 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5 12.5
63
14 6
Overall length
Ø3h
6
Ø3h
6
Thread length
wrench flat 8
Ø5h
8
(3)Thread length
Overall length
7,5
M6x
0,75
Ø4,
5h6
3
77 15,5
Ø9,
5
Ø6g
5■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table. Please follow the advice on page 24/25.
P
1510
/0,5
.5.9
0.11
0
1510
/0,5
.5.6
5.10
5
1510
/0,5
.5.1
25.1
65
1510
/1.5
.90.
110
1510
/1.5
.65.
105
1510
/1.5
.125
.165
1510
/1,5
.5.9
0.11
0
1510
/1,5
.5.6
5.10
5
1510
/1,5
.5.1
25.1
65
A B B A B B A B B
0.5 0.5 0.5 1 1 1 1.5 1.5 1.5
5 5 5 5 5 5 5 5 5
60 40 100 60 40 100 60 40 100
2 2 2 2 2 2 2 2 2
0.6 0.6 0.6 0.8 0.8 0.8 1 1 1
100 100 100 400 400 400 500 500 500
100 100 100 500 500 500 600 600 600
- - - - - - - - -
- - - - - - - - -
10 10 10 20 20 20 20 20 20
6 6 6 15 15 15 15 15 15
0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0 0.5-1.0
36 36 36 36 36 36 36 36 36
15 15 15 15 15 15 15 15 15
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
64
LFLF6
D1 22 28
30°
1919
30°
16
ØØ3,4
N O M I N A L D I A M E T E R 8 m m Ground execution with standard bearing journal P0 - P5
Series 1412
F L A N G E N U T■ Series 1412: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1412
/0,5
.8.1
45.1
70
1412
/0,5
.8.2
45.2
70
1412
/0,5
.8.8
0.13
8
1412
/0,5
.8.1
90.
248
1412
/1.8
.145
.170
1412
/1.8
.245
.270
1412
/1.8
.80.
138
1412
/1.8
.19
0.24
8
1412
/1,5
.8.1
10.1
68
1412
/1,5
.8.1
90.
248
1412
/2.8
.145
.170
1412
.2.8
.245
.270
Shaft style A A B B A A B B B B A A
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1 1.5 1.5 2 2
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 70 150 100 200
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 1 1 1.5 1.5
Dynamic load capacity Ca [N] 400 400 400 400 900 900 900 900 1200 1200 2000 2000
Static load capacity C0a [N] 500 500 500 500 1200 1200 1200 1200 1500 1500 2100 2100
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LF [mm] 22 22 22 22 23 23 23 23 23 23 28 28
Nut diameter D1g6 [mm] 16 16 16 16 16 16 16 16 16 16 16 16
65
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
■ Shaft style A
■ Shaft style B
P
1412
/2.8
.80.
138
1412
/2.8
.19
0.24
8
1412
/2,5
.8.1
45.1
70
1412
/2,5
.8.2
45.2
70
1412
/2,5
.8.8
0.13
8
1412
/2,5
.8.1
90.
248
1412
/3.8
.145
.170
1412
/3.8
.245
.270
1412
/3.8
.80.
138
1412
/3.8
.19
0.24
8
1412
/4.8
.145
.170
1412
/4.8
.245
.270
1412
/4.8
.80.
138
1412
/4.8
.19
0.24
8
B B A A B B A A B B A A B B
2 2 2.5 2.5 2.5 2.5 3 3 3 3 4 4 4 4
8 8 8 8 8 8 8 8 8 8 8 8 8 8
40 150 100 200 40 150 100 200 40 150 100 200 40 150
3 3 3 3 3 3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000
2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100
0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
28 28 30 30 30 30 27 27 27 27 31 31 31 31
16 16 16 16 16 16 16 16 16 16 16 16 16 16
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
66
LFLF6
D1 22 28
30°
1919
30°
L3
16
ØØ3,4
N O M I N A L D I A M E T E R 8 m m Ground execution with standard bearing journal P0 - P5
Series 2412
F L A N G E N U T■ Series 2412: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
2412
/2.8
.145
.170
2412
/2.8
.245
.270
2412
/2.8
.80.
138
2412
/2.8
.19
0.24
8
2412
/4.8
.145
.170
2412
/4.8
.245
.270
2412
/4.8
.80.
138
2412
/4.8
.19
0.24
8
2412
/5.8
.145
.170
2412
/5.8
.245
.270
2412
/5.8
.80.
138
2412
/5.8
.19
0.24
8
Shaft style A A B B A A B B A A B B
Lead P [mm] 2 2 2 2 4 4 4 4 5 5 5 5
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 5 5 5 5 5 5 5 5 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 3100 3100 3100 3100 3000 3000 3000 3000 1900 1900 1900 1900
Static load capacity C0a [N] 3600 3600 3600 3600 3600 3600 3600 3600 2100 2100 2100 2100
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LF [mm] 11 11 11 11 22 22 22 22 15 15 15 15
Nut diameter D1g6 [mm] 16 16 16 16 16 16 16 16 16 16 16 16
Länge Stirndeckel L3 [mm] 5 5 5 5 6 6 6 6 5 5 5 5
67
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
■ Shaft style A
■ Shaft style B
P
2412
/8.8
.145
.170
2412
/8.8
.245
.270
2412
/8.8
.80.
138
2412
/8.8
.19
0.24
8
A A B B
8 8 8 8
8 8 8 8
100 200 40 150
2 2 2 2
1.5 1.5 1.5 1.5
1200 1200 1200 1200
1200 1200 1200 1200
0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
16 16 16 16
16 16 16 16
6 6 6 6
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
68
LZ
DZ
N O M I N A L D I A M E T E R 8 m m Ground execution with standard bearing journal P0 - P5
Series 1214
C Y L I N D R I C A L N U T■ Series 1214: Cylindrical nut without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1214
/0,5
.8.1
45.1
70
1214
/0,5
.8.2
45.2
70
1214
/0,5
.8.8
0.13
8
1214
/0,5
.8.1
90.
248
1214
/1.8
.145
.170
1214
/1.8
.245
.270
1214
/1.8
.80.
138
1214
/1.8
.19
0.24
8
1214
/1,5
.8.1
45.1
70
1214
/1,5
.8.2
45.2
70
1214
/1,5
.8.8
0.13
8
1214
/1,5
.8.1
90.
248
Shaft style A A B B A A B B A A B B
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1 1.5 1.5 1.5 1.5
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 1 1 1 1
Dynamic load capacity Ca [N] 400 400 400 400 900 900 900 900 1200 1200 1200 1200
Static load capacity C0a [N] 500 500 500 500 1200 1200 1200 1200 1500 1500 1500 1500
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LZ [mm] 13 13 13 13 14 14 14 14 14 14 14 14
Nut diameter DZh6 [mm] 15 15 15 15 15 15 15 15 15 15 15 15
69
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
■ Shaft style A
■ Shaft style B
P
1214
/2.8
.145
.170
1214
/2.8
.245
.270
1214
/2.8
.80.
138
1214
/2.8
.19
0.24
8
1214
/2,5
.8.1
45.1
70
1214
/2,5
.8.2
45.2
70
1214
/2,5
.8.8
0.13
8
1214
/2,5
.8.1
90.
248
1214
/3.8
.145
.170
1214
/3.8
.245
.270
1214
/3.8
.80.
138
1214
/3.8
.19
0.24
8
1214
/4.8
.145
.170
1214
/4.8
.245
.270
1214
/4.8
.80.
138
1214
/4.8
.19
0.24
8A A B B A A B B A A B B A A B B
2 2 2 2 2.5 2.5 2.5 2.5 3 3 3 3 4 4 4 4
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
100 200 40 150 100 200 40 150 100 200 40 150 100 200 40 150
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000
2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100
0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
19 19 19 19 21 21 21 21 18 18 18 18 22 22 22 22
15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
70
8LA
M14x1
for pin wrench Ø3
DA
N O M I N A L D I A M E T E R 8 m m Ground execution with standard bearing journal P0 - P5
Series 1112
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1112: Nut with connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1112
/0,5
.8.1
45.1
70
1112
/0,5
.8.2
45.2
70
1112
/0,5
.8.8
0.13
8
1112
/0,5
.8.1
90.2
48
1112
/1.8
.145
.170
1112
/1.8
.245
.270
1112
/1.8
.80.
138
1112
/1.8
.190
.248
1112
/1,5
.8.1
45.1
70
1112
/1,5
.8.1
245.
270
1112
/1,5
.8.8
0.13
8
1112
/1,5
.8.1
90.2
48
Shaft style A A B B A A B B A A B B
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1 1.5 1.5 1.5 1.5
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 1 1 1 1
Dynamic load capacity Ca [N] 400 400 400 400 900 900 900 900 1200 1200 1200 1200
Static load capacity C0a [N] 500 500 500 500 1200 1200 1200 1200 1500 1500 1500 1500
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LA [mm] 21 21 21 21 22 22 22 22 22 22 22 22
Nut diameter DA [mm] 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5
71
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
P
1112
/2.8
.145
.170
1112
/2.8
.245
.270
1112
/2.8
.80.
138
1112
/2.8
.190
.248
1112
/2,5
.8.1
45.1
70
1112
/2,5
.8.2
45.2
70
1112
/2,5
.8.8
0.13
8
1112
/2,5
.8.1
90.2
48
1112
/3.8
.145
.170
1112
/3.8
.245
.270
1112
/3.8
.80.
138
1112
/3.8
.190
.248
1112
/4.8
.145
.170
1112
/4.8
.245
.270
1112
/4.8
.80.
138
1112
/4.8
.190
.248
A A B B A A B B A A B B A A B B
2 2 2 2 2.5 2.5 2.5 2.5 3 3 3 3 4 4 4 4
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
100 200 40 150 100 200 40 150 100 200 40 150 100 200 40 150
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000 2000
2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100 2100
0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
27 27 27 27 29 29 29 29 26 26 26 26 30 30 30 30
16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
72
M14x1
LD10
DDwrench flat 17
4 54,5 88
N O M I N A L D I A M E T E R 8 m m Ground execution with standard bearing journal P0 - P5
Series 1510
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1510: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1510
/0,5
.8.1
45.1
70
1510
/0,5
.8.2
45.2
70
1510
/0,5
.8.8
0.13
8
1510
/0,5
.8.1
90.2
48
1510
/1.8
.145
.170
1510
/1.8
.245
.270
1510
/1.8
.80.
138
1510
/1.8
.190
.248
1510
/2.8
.145
.170
1510
/2.8
.245
.270
1510
/2.8
.80.
138
1510
/2.8
.190
.248
Shaft style A A B B A A B B A A B B
Lead P [mm] 0.5 0.5 0.5 0.5 1 1 1 1 2 2 2 2
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 2 2 2 2 2 2 2 2 2 2 2 2
Ball diameter [mm] 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 200 200 200 200 600 600 600 600 1400 1400 1400 1400
Static load capacity C0a [N] 300 300 300 300 800 800 800 800 1400 1400 1400 1400
Max. preload [N] 15 15 15 15 30 30 30 30 50 50 50 50
Max. axial load [N] 10 10 10 10 20 20 20 20 40 40 40 40
Friction torque Tpr0 [Ncm] 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5
Nut length LD [mm] 40 40 40 40 40 40 40 40 40 40 40 40
Nut diameter DD [mm] 20 20 20 20 20 20 20 20 20 20 20 20
73
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
(4)
Overall length
10 9 18 8
Thread length
9
6 Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
■ Shaft style A
■ Shaft style B
Please follow the advice on page 24/25.
P
1510
/.2,5
.8.1
45.1
70
1510
/2,5
.8.2
45.2
70
1510
/2,5
.8.8
0.13
8
1510
/2,5
.8.1
90.2
48
A A B B
2.5 2.5 2.5 2.5
8 8 8 8
100 200 40 150
2 2 2 2
1.5 1.5 1.5 1.5
1400 1400 1400 1400
1400 1400 1400 1400
50 50 50 50
40 40 40 40
0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5
40 40 40 40
20 20 20 20
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
74
8LFLF L9L9
D44 D6D
30° 30°
D1-0,6
Ø4,5
D1 D1-0,6
10
8LFLF L9L9
D44 D6D
30° 30°
L3
D1-0,6
Ø4,5
D1 D1-0,6
10
F L A N G E N U T■ Series 2412, 2422: Nut with fl ange and standard wipers on
both ends
N O M I N A L D I A M E T E R 12 m m Ground execution with standard bearing journal P0 - P5
Series 1412, 2412, 2422
F L A N G E N U T■ Series 1412: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1412
/1.1
2.35
5.39
7
1412
/1.1
2.16
0.23
0
1412
/1.1
2.51
0.58
0
1412
/2.1
2.35
5.39
7
1412
/2.1
2.16
0.23
0
1412
/2.1
2.51
0.58
0
1412
/3.1
2.35
5.39
7
1412
/3.1
2.16
0.23
0
1412
/3.1
2.51
0.58
0
1412
/4.1
2.35
5.39
7
1412
/4.1
2.16
0.23
0
1412
/4.1
2.51
0.58
0
Shaft style A B B A B B A B B A B B
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.8 0.8 0.8 1.5 1.5 1.5 2 2 2 2 2 2
Dynamic load capacity Ca [N] 1100 1100 1100 2500 2500 2500 3600 3600 3600 3600 3600 3600
Static load capacity C0a [N] 2000 2000 2000 3400 3400 3400 4300 4300 4300 4300 4300 4300
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
Nut length LF [mm] 25 25 25 30 30 30 37 37 37 36 36 36
Nut diameter D1g6 [mm] 20 20 20 20 20 20 22 22 22 22 22 22
L3 [mm] - - - - - - - - - - - -
D4 [mm] 29 29 29 29 29 29 29 29 29 29 29 29
D6 [mm] 37 37 37 37 37 37 37 37 37 37 37 37
L9 [mm] 24 24 24 24 24 24 24 24 24 24 24 24
75
■ Shaft style A
■ Shaft style B
P
Nuts shown in standard orientation. Select one nut from table.
1412
/5.1
2.35
5.39
7
1412
/5.1
2.16
0.23
0
1412
/5.1
2.51
0.58
0
2412
/5.1
2.35
5.39
7
2412
/5.1
2.16
0.23
0
2412
/5.1
2.51
0.58
0
2422
/10.
12.3
55.3
97
2422
/10.
12.1
60.2
30
2422
/10.
12.5
10.5
80
2422
/10.
12.3
55.3
97
2422
/10.
12.1
60.2
30
2422
/10.
12.5
10.5
80
A B B A B B A B B A B B
5 5 5 5 5 5 10 10 10 10 10 10
12 12 12 12 12 12 12 12 12 12 12 12
300 100 450 300 100 450 300 100 450 300 100 450
3 3 3 5 5 5 2 + 2 2 + 2 2 + 2 3 + 3 3 + 3 3 + 3
2 2 2 2 2 2 2.5 2.5 2.5 2.5 2.5 2.5
3600 3600 3600 5600 5600 5600 5800 5800 5800 8500 8500 8500
4300 4300 4300 7600 7600 7600 7000 7000 7000 11100 11100 11100
0.02 0.02 0.02 0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03
1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
39 39 39 25 25 25 20 20 20 30 30 30
22 22 22 24 24 24 24 24 24 24 24 24
- - - 7 7 7 9 9 9 9 9 9
29 29 29 32 32 32 32 32 32 32 32 32
37 37 37 40 40 40 40 40 40 40 40 40
24 24 24 26 26 26 26 26 26 26 26 26
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
(5)
Ø11
,5h8
15 10 20 10
5
Thread length
10
7
Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
76
16 (P=2:12))
555
LP
keyway 1.9 dpLZ
DZ
10LA
M18x1x
for pin wrench Ø3
DA
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1112: Cylindrical nut without wipers
N O M I N A L D I A M E T E R 12 m m Ground execution with standard bearing journal P0 - P5
Series 1214, 1112
C Y L I N D R I C A L N U T■ Series 1214: Cylindrical nut without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1214
/1.1
2.35
5.39
7
1214
/1.1
2.16
0.23
0
1214
/1.1
2.51
0.58
0
1214
/2.1
2.35
5.39
7
1214
/2.1
2.16
0.23
0
1214
/2.1
2.51
0.58
0
1214
/3.1
2.35
5.39
7
1214
/3.1
2.16
0.23
0
1214
/3.1
2.51
0.58
0
1214
/4.1
2.35
5.39
7
1214
/4.1
2.16
0.23
0
1214
/4.1
2.51
0.58
0
1214
/5.1
2.35
5.39
7
Shaft style A B B A B B A B B A B B A
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4 5
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450 300
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 0.8 0.8 0.8 1.5 1.5 1.5 2 2 2 2 2 2 2
Dynamic load capacity Ca [N] 1100 1100 1100 2500 2500 2500 3600 3600 3600 3600 3600 3600 3600
Static load capacity C0a [N] 2000 2000 2000 3400 3400 3400 4300 4300 4300 4300 4300 4300 4300
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
Nut length LZ / LA [mm] 17 17 17 19 19 19 26 26 26 22 22 22 26
Nut diameter Dzh6 / DA [mm] 19 19 19 19 19 19 19 19 19 19 19 19 19
LP [mm] 2.5 2.5 2.5 1.5 1.5 1.5 5 5 5 3.5 3.5 3.5 5
77
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
(5)
Ø11
,5h8
15 10 20 10
5
Thread length
10
7
Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
P
1214
/5.1
2.16
0.23
0
1214
/5.1
2.51
0.58
0
1112
/1.1
2.35
5.39
7
1112
/1.1
2.16
0.23
0
1112
/1.1
2.51
0.58
0
1112
/2.1
2.35
5.39
7
1112
/2.1
2.16
0.23
0
1112
/2.1
2.51
0.58
0
1112
/3.1
2.35
5.39
7
1112
/3.1
2.16
0.23
0
1112
/3.1
2.51
0.58
0
1112
/4.1
2.35
5.39
7
1112
/4.1
2.16
0.23
0
1112
/4.1
2.51
0.58
0
1112
/5.1
2.35
5.39
7
1112
/5.1
2.16
0.23
0
1112
/5.1
2.51
0.58
0B B A B B A B B A B B A B B A B B
5 5 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
100 450 300 100 450 300 100 450 300 100 450 300 100 450 300 100 450
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
2 2 0.8 0.8 0.8 1.5 1.5 1.5 2 2 2 2 2 2 2 2 2
3600 3600 1100 1100 1100 2500 2500 2500 3600 3600 3600 3600 3600 3600 3600 3600 3600
4300 4300 2000 2000 2000 3400 3400 3400 4300 4300 4300 4300 4300 4300 4300 4300 4300
0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
26 26 24 24 24 29 29 29 36 36 36 33 33 33 36 36 36
19 19 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 22.5 22.5 22.5 22.5 22.5 22.5
5 5 - - - - - - - - - - - - - - -
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
78
M18x1
LD10
DD
6 56,51010
wrenchflat 22
N O M I N A L D I A M E T E R 12 m m Ground execution with standard bearing journal P0 - P5
Series 1510
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1510: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1510
/1.1
2.35
5.39
7
1510
/1.1
2.16
0.23
0
1510
/1.1
2.51
0.58
0
1510
/2.1
2.35
5.39
7
1510
/2.1
2.16
0.23
0
1510
/2.1
2.51
0.58
0
1510
/3.1
2.35
5.39
7
1510
/3.1
2.16
0.23
0
1510
/3.1
2.51
0.58
0
1510
/4.1
2.35
5.39
7
1510
/4.1
2.16
0.23
0
1510
/4.1
2.51
0.58
0
Shaft style A B B A B B A B B A B B
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450
Ball circles i 2 2 2 2 2 2 2 2 2 2 2 2
Ball diameter [mm] 0.8 0.8 0.8 1.5 1.5 1.5 2 2 2 2 2 2
Dynamic load capacity Ca [N] 800 800 800 1800 1800 1800 2500 2500 2500 2500 2500 2500
Static load capacity C0a [N] 1300 1300 1300 2200 2200 2200 2800 2800 2800 2800 2800 2800
Max. preload [N] 50 50 50 80 80 80 80 80 80 80 80 80
Max. axial load [N ] 40 40 40 70 70 70 70 70 70 70 70 70
Friction torque Tpr0 [Ncm] 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0 1.0 - 2.0
Nut length LD [mm] 49 49 49 49 49 49 49 49 49 49 49 49
Nut diameter DD [mm] 24 24 24 24 24 24 24 24 24 24 24 24
79
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
Ø11
,5h8
(5)
15 10 20 10
5
Thread length
10
7 Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
■ Shaft style A
■ Shaft style B
Please follow the advice on page 24/25.
P
1510
/5.1
2.35
5.39
7
1510
/5.1
2.16
0.23
0
1510
/5.1
2.51
0.58
0
A B B
5 5 5
12 12 12
300 100 450
2 2 2
2 2 2
2500 2500 2500
2800 2800 2800
80 80 80
70 70 70
1.0 - 2.0 1.0 - 2.0 1.0 - 2.0
49 49 49
24 24 24
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
80
LF1010
lube hole M6
L9
30°
D6D
330°°
D44D1-0,6D1-0,6D111
55,5Ø
1313
LF10
lube hole M6
L9
30°
D6
30°
D4D1-0,6
L3
D1-0,6D1
5,5Ø
13
N O M I N A L D I A M E T E R 16 m m Ground execution with standard bearing journal P0 - P5
Series 1412, 2422
F L A N G E N U T■ Series 1412: Nut with fl ange and standard wipers on
both ends
F L A N G E N U T■ Series 2422: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1412
/2.1
6.47
0.52
7
1412
/2.1
6.18
9.27
1
1412
/2.1
6.68
9.77
1
1412
/4.1
6.47
0.52
7
1412
/4.1
6.18
9.27
1
1412
/4.1
6.68
9.77
1
1412
/5.1
6.47
0.52
7
1412
/5.1
6.18
9.27
1
1412
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B
Lead P [mm] 2 2 2 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600
Ball circles i 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
Dynamic load capacity Ca [N] 2900 2900 2900 8900 8900 8900 10100 10100 10100
Static load capacity C0a [N] 4900 4900 4900 11400 11400 11400 12000 12000 12000
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03
Max. friction torque [Ncm] (preloaded nut) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
Nut length LF [mm] 32 32 32 38 38 38 44 44 44
Nut diameter D1g6 [mm] 25 25 25 28 28 28 28 28 28
L3 [mm] - - - - - - - - -
D4 [mm] 35 35 35 38 38 38 38 38 38
D6 [mm] 44 44 44 48 48 48 48 48 48
L9 [mm] 29 29 29 31 31 31 31 31 31
81
Ø12
h6
M12
x1
Ø10
h6
Ø12
h6
6
12 32 13
Thread length
Overall length
wrench flat 13
(5)
Ø10
h6
M12
x1
Ø12
g5
Ø15
,5h8
8
15 10 20 10
5
12
Ø10
g6
Ø9,6x1,15
Thread length
Overall length
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
*Please specify the number of circles
P
2422
/10.
16.4
70.5
27*
2422
/10.
16.1
89.2
71*
2422
/10.
16.6
89.7
71*
2422
/10.
16.4
70.5
27*
2422
/10.
16.1
89.2
71*
2422
/10.
16.6
89.7
71*
2422
/16.
16.4
70.5
27
2422
/16.
16.1
89.2
71
2422
/16.
16.6
89.7
71
2422
/20.
16.4
70.5
27
2422
/20.
16.1
89.2
71
2422
/20.
16.6
89.7
71
2422
/30.
16.4
70.5
27
2422
/30.
16.1
89.2
71
2422
/30.
16.6
89.7
71
A B B A B B A B B A B B A B B
10 10 10 10 10 10 16 16 16 20 20 20 30 30 30
16 16 16 16 16 16 16 16 16 16 16 16 16 16 16
400 100 600 400 100 600 400 100 600 400 100 600 400 100 600
3 + 3 3 + 3 3 + 3 5 + 5 5 + 5 5 + 5 2 + 2 2 + 2 2 + 2 2 + 2 2 + 2 2 + 2 0.5 + 0.5 0.5 + 0.5 0.5 + 0.5
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
19600 19600 19600 31400 31400 31400 13400 13400 13400 13000 13000 13000 2300 2300 2300
27700 27700 27700 47800 47800 47800 47800 18300 18300 17900 17900 17900 2500 2500 2500
0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03 0.03
1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
32 32 32 52 52 52 31 31 31 28 28 28 26 26 26
32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
12 12 12 12 12 12 10 10 10 10 10 10 12 12 12
42 42 42 42 42 42 42 42 42 42 42 42 42 42 42
52 52 52 52 52 52 52 52 52 52 52 52 52 52 52
40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
82
16 (P=2:12))
555
LP
keyway 1.9 dpLZLZ
DZ
N O M I N A L D I A M E T E R 16 m m Ground execution with standard bearing journal P0 - P5
Series 1214, 1112
C Y L I N D R I C A L N U T■ Series 1214: Cylindrical nut without wipers
10LA
M22x1
for pin wrench Ø3
DAD
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1112: Nut with connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1214
/2.1
6.47
0.52
7
1214
/2.1
6.18
9.27
1
1214
/2.1
6.68
9.77
1
1214
/4.1
6.47
0.52
7
1214
/4.1
6.18
9.27
1
1214
/4.1
6.68
9.77
1
1214
/5.1
6.47
0.52
7
1214
/5.1
6.18
9.27
1
1214
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B
Lead P [mm] 2 2 2 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600
Ball circles i 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
Dynamic load capacity Ca [N] 2900 2900 2900 8900 8900 8900 10100 10100 10100
Static load capacity C0a [N] 4900 4900 4900 11400 11400 11400 12000 12000 12000
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03
Max. friction torque [Ncm] (preloaded nut) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
Nut length LZ / LA [mm] 19 19 19 21 21 21 27 27 27
Nut diameter DZh6 / DA [mm] 28 28 28 28 28 28 28 28 28
LP [mm] 1.5 1.5 1.5 2.5 2.5 2.5 5.5 5.5 5.5
83
Ø12
h6
M12
x1
Ø10
h6
Ø12
h6
6
12 32 13
Thread length
Overall length
wrench flat 13
(5)
Ø10
h6
M12
x1
Ø12
g5
Ø15
,5h8
8
15 10 20 10
5
12
Ø10
g6
Ø9,6x1,15
Thread length
Overall length
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
P
1112
/2.1
6.47
0.52
7
1112
/2.1
6.18
9.27
1
1112
/2.1
6.68
9.77
1
1112
/4.1
6.47
0.52
7
1112
/4.1
6.18
9.27
1
1112
/4.1
6.68
9.77
1
1112
/5.1
6.47
0.52
7
1112
/5.1
6.18
9.27
1
1112
/5.1
6.68
9.77
1
A B B A B B A B B
2 2 2 4 4 4 5 5 5
16 16 16 16 16 16 16 16 16
400 100 600 400 100 600 400 100 600
3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
2900 2900 2900 8900 8900 8900 10100 10100 10100
4900 4900 4900 11400 11400 11400 12000 12000 12000
0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03
1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
29 29 29 36 36 36 43 43 43
25.5 25.5 25.5 28.5 28.5 28.5 28.5 28.5 28.5
- - - - - - - - -
P o s i t i o n i n g b a l l s c r e w s 3 - 1 6 m m
84
M22x12
LA10
DAA
8,58,51010
wrench flat 30
N O M I N A L D I A M E T E R 16 m m Ground execution with standard bearing journal P0 - P5
Series 1510
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1510: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1510
/2.1
6.47
0.52
7
1510
/2.1
6.18
9.27
1
1510
/2.1
6.68
9.77
1
1510
/2,5
.16.
470.
527
1510
/2,5
.16.
189.
271
1510
/2,5
.16.
689.
771
1510
/4.1
6.47
0.52
7
1510
/4.1
6.18
9.27
1
1510
/4.1
6.68
9.77
1
1510
/5.1
6.47
0.52
7
1510
/5.1
6.18
9.27
1
1510
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B A B B
Lead P [mm] 2 2 2 2.5 2.5 2.5 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600 400 100 600
Ball circles i 2 2 2 2 2 2 2 2 2 2 2 2
Ball diameter [mm] 1.5 1.5 1.5 1.5 1.5 1.5 2 2 2 2.5 2.5 2.5
Dynamic load capacity Ca [N] 2100 2100 2100 2100 2100 2100 3000 3000 3000 3900 3900 3900
Static load capacity C0a [N] 3200 3200 3200 3200 3200 3200 4000 4000 4000 4700 4700 4700
Max. preload [N] 120 120 120 120 120 120 120 120 120 150 150 150
Max. axial load [N ] 100 100 100 100 100 100 100 100 100 130 130 130
Friction torque Tpr0 [Ncm] 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0
Nut length LA [mm] 57 57 57 57 57 57 57 57 57 57 57 57
Nut diameter DA [mm] 33 33 33 33 33 33 33 33 33 33 33 33
85
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
Ø11
,5h8
(5)
15 10 20 10
5
Thread length
10
7 Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
■ Shaft style A
■ Shaft style B
P
Please follow the advice on page 24/25.
86
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
LFLF6
D1 22 28
30°
1919
30°
16
ØØ3,4
N O M I N A L D I A M E T E R 8 m mRolled execution with standard bearing journal T7 - T10
Series 1432
F L A N G E N U T■ Series 1432: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1432
/1.8
.145
.170
1432
/1.8
.245
.270
1432
/1.8
.80.
138
1432
/1.8
.19
0.24
8
1432
/2.8
.145
.170
1432
/2.8
.245
.270
1432
/2.8
.80.
138
1432
/2.8
.19
0.24
8
1432
/2,5
.8.1
45.1
70
1432
/2,5
.8.2
45.2
70
1432
/2,5
.8.8
0.13
8
1432
/2,5
.8.1
90.
248
Shaft style A A B B A A B B A A B B
Lead P [mm] 1 1 1 1 2 2 2 2 2.5 2.5 2.5 2.5
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1 1 1 1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 1100 1100 1100 1100 1800 1800 1800 1800 1800 1800 1800 1800
Static load capacity C0a [N] 1400 1400 1400 1400 1900 1900 1900 1900 1900 1900 1900 1900
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LF [mm] 23 23 23 23 28 28 28 28 30 30 30 30
Nut diameter D1g6 [mm] 16 16 16 16 16 16 16 16 16 16 16 16
87
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
■ Shaft style A
■ Shaft style B
T
1432
/3.8
.145
.170
1432
/3.8
.245
.270
1432
/3.8
.80.
138
1432
/3.8
.19
0.24
8
1432
/4.8
.145
.170
1432
/4.8
.245
.270
1432
/4.8
.80.
138
1432
/4.8
.19
0.24
8
A A B B A A B B
3 3 3 3 4 4 4 4
8 8 8 8 8 8 8 8
100 200 40 150 100 200 40 150
3 3 3 3 3 3 3 3
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1800 1800 1800 1800 1800 1800 1800 1800
1900 1900 1900 1900 1900 1900 1900 1900
0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
27 27 27 27 31 31 31 31
16 16 16 16 16 16 16 16
88
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
LFLF6
D1 22 28
30°
1919
30°
L3
16
ØØ3,4
N O M I N A L D I A M E T E R 8 m mRolled execution with standard bearing journal T7 - T10
Series 2432
F L A N G E N U T■ Series 2432: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
2432
/2.8
.145
.170
2432
/2.8
.245
.270
2432
/2.8
.80.
138
2432
/2.8
.19
0.24
8
2432
/4.8
.145
.170
2432
/4.8
.245
.270
2432
/4.8
.80.
138
2432
/4.8
.19
0.24
8
2432
/5.8
.145
.170
2432
/5.8
.245
.270
2432
/5.8
.80.
138
2432
/5.8
.19
0.24
8
Shaft style A A B B A A B B A A B B
Lead P [mm] 2 2 2 2 4 4 4 4 5 5 5 5
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 5 5 5 5 5 5 5 5 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 2800 2800 2800 2800 2800 2800 2800 2800 1800 1800 1800 1800
Static load capacity C0a [N] 3300 3300 3300 3300 3300 3300 3300 3300 1900 1900 1900 1900
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LF [mm] 11 11 11 11 22 22 22 22 15 15 15 15
Nut diameter D1g6 [mm] 16 16 16 16 16 16 16 16 16 16 16 16
L3 [mm] 5 5 5 5 6 6 6 6 5 5 5 5
89
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
T
90
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
LZ
DZ
8LA
M14x1
for pin wrench Ø3
DA
N O M I N A L D I A M E T E R 8 m mRolled execution with standard bearing journal T7 - T10
Series 1234, 1132
C Y L I N D R I C A L N U T■ Series 1234: Cylindrical nut without wipers
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1132: Nut with connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1234
/1.8
.145
.170
1234
/1.8
.245
.270
1234
/1.8
.80.
138
1234
/1.8
.19
0.24
8
1234
/2.8
.145
.170
1234
/2.8
.245
.270
1234
/2.8
.19
0.24
8
1234
/2,5
.8.1
45.1
70
1234
/2,5
.8.2
45.2
70
1234
/2,5
.8.8
0.13
8
1234
/2,5
.8.1
90.
248
1234
/3.8
.145
.170
Shaft style A A B B A A B A A B B A
Lead P [mm] 1 1 1 1 2 2 2 2.5 2.5 2.5 2.5 3
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 150 100 200 40 150 100
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1 1 1 1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 1100 1100 1100 1100 1800 1800 1800 1800 1800 1800 1800 1800
Static load capacity C0a [N] 1400 1400 1400 1400 1900 1900 1900 1900 1900 1900 1900 1900
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Nut length LZ / LA [mm] 14 14 14 14 19 19 19 21 21 21 21 18
Nut diameter DZh6 / DA [mm] 15 15 15 15 15 15 15 15 15 15 15 15
91
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
T
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
1234
/3.8
.245
.270
1234
/3.8
.80.
138
1234
/3.8
.19
0.24
8
1234
/4.8
.145
.170
1234
/4.8
.245
.270
1234
/4.8
.80.
138
1234
/4.8
.19
0.24
8
1132
/1.8
.145
.170
1132
/1.8
.245
.270
1132
/1.8
.80.
138
1132
/1.8
.190
.248
1132
/2.8
.145
.170
1132
/2.8
.245
.270
1132
/2.8
.80.
138
1132
/2.8
.190
.248
A B B A A B B A A B B A A B B
3 3 3 4 4 4 4 1 1 1 1 2 2 2 2
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
200 40 150 100 200 40 150 100 200 40 150 100 200 40 150
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1 1 1 1 1.5 1.5 1.5 1.5
1800 1800 1800 1800 1800 1800 1800 1100 1100 1100 1100 1800 1800 1800 1800
1900 1900 1900 1900 1900 1900 1900 1400 1400 1400 1400 1900 1900 1900 1900
0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.01 0.01 0.01 0.01 0.02 0.02 0.02 0.02
0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
18 18 18 22 22 22 22 22 22 22 22 27 27 27 27
15 15 15 15 15 15 15 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5
92
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
8LA
M14x1
for pin wrench Ø3
DA
N O M I N A L D I A M E T E R 8 m mRolled execution with standard bearing journal T7 - T10
Series 1132, 1530
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1132: Nut with connecting thread without wipers
M14x1
LD10
DDwrench flat17
4 54,5 88 N U T W I T H C O N N E C T I N G T H R E A D■ Series 1530: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1132
/2,5
.8.1
45.1
70
1132
/2,5
.8.2
45.2
70
1132
/2,5
.8.8
0.13
8
1132
/2,5
.8.1
90.2
48
1132
/3.8
.145
.170
1132
/3.8
.245
.270
1132
/3.8
.80.
138
1132
/3.8
.190
.248
1132
/4.8
.145
.170
1132
/4.8
.245
.270
1132
/4.8
.80.
138
1132
/4.8
.190
.248
Shaft style A A B B A A B B A A B B
Lead P [mm] 2.5 2.5 2.5 2.5 3 3 3 3 4 4 4 4
Nominal diameter dN [mm] 8 8 8 8 8 8 8 8 8 8 8 8
Nominal stroke [mm] 100 200 40 150 100 200 40 150 100 200 40 150
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
Dynamic load capacity Ca [N] 1800 1800 1800 1800 1800 1800 1800 1800 1800 1800 1800 1800
Static load capacity C0a [N] 1900 1900 1900 1900 1900 1900 1900 1900 1900 1900 1900 1900
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2) 0.5 (2)
Max. preload [N] - - - - - - - - - - - -
Max. axial load [N] - - - - - - - - - - - -
Friction torque Tpr0 [Ncm] - - - - - - - - - - - -
Nut length LA / LD [mm] 29 29 29 29 26 26 26 26 30 30 30 30
Nut diameter DA / DD [mm] 16.5 16.5 16.5 165 16.5 16.5 16.5 16.5 16.5 16.5 16.5 16.5
93
wrench flat 10
Ø8h
8
6
(4)
Overall length
10 9 18 8
Thread length
9
Ø5,7x0,8
Ø6g
6
4
Ø11
,5
Ø8g
5
Ø6h
6
M8x
1
Ø6h
6
Ø6h
6
18 7
Thread length
Overall length
T
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table. Please follow the advice on page 24/25.
1530
/1.8
.145
.170
1530
/1.8
.245
.270
1530
/1.8
.80.
138
1530
/1.8
.190
.248
1530
/2.8
.145
.170
1530
/2.8
.245
.270
1530
/2.8
.80.
138
1530
/2.8
.190
.248
1530
/2,5
.8.1
45.1
70
1530
/2,5
.8.2
45.2
70
1530
/2,5
.8.8
0.13
8
1530
/2,5
.8.1
90.2
48
A A B B A A B B A A B B
1 1 1 1 2 2 2 2 2.5 2.5 2.5 2.5
8 8 8 8 8 8 8 8 8 8 8 8
100 200 40 150 100 200 40 150 100 200 40 150
2 2 2 2 2 2 2 2 2 2 2 2
1 1 1 1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
800 800 800 800 1300 1300 1300 1300 1300 1300 1300 1300
900 900 900 900 1300 1300 1300 1300 1300 1300 1300 1300
- - - - - - - - - - - -
- - - - - - - - - - - -
30 30 30 30 50 50 50 50 50 50 50 50
20 20 20 20 40 40 40 40 40 40 40 40
0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5 0.7-1.5
40 40 40 40 40 40 40 40 40 40 40 40
20 20 20 20 20 20 20 20 20 20 20 20
94
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
8LFLF L9L9
D44 D6D
30° 30°
D1-0,6
Ø4,5
D1 D1-0,6
10
8LFLF L9L9
D44 D6D
30° 30°
L3
D1-0,6
ØØ4,5
D1 D1-0,6
10
F L A N G E N U T■ Series 2432, 2442: Nut with fl ange and standard wipers on
both ends
N O M I N A L D I A M E T E R 12 m mRolled execution with standard bearing journal T7 - T10
Series 1432, 2432, 2442
F L A N G E N U T■ Series 1432: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1432
/1.1
2.35
5.39
7
1432
/1.1
2.16
0.23
0
1432
/1.1
2.51
0.58
0
1432
/2.1
2.35
5.39
7
1432
/2.1
2.16
0.23
0
1432
/2.1
2.51
0.58
0
1432
/3.1
2.35
5.39
7
1432
/3.1
2.16
0.23
0
1432
/3.1
2.51
0.58
0
1432
/4.1
2.35
5.39
7
1432
/4.1
2.16
0.23
0
1432
/4.1
2.51
0.58
0
Shaft style A B B A B B A B B A B B
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2
Dynamic load capacity Ca [N] 1300 1300 1300 2300 2300 2300 3300 3300 3300 3300 3300 3300
Static load capacity C0a [N] 2200 2200 2200 3100 3100 3100 3900 3900 3900 3900 3900 3900
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
Nut length LF [mm] 25 25 25 30 30 30 37 37 37 36 36 36
Nut diameter D1g6 [mm] 20 20 20 20 20 20 22 22 22 22 22 22
L3 [mm] - - - - - - - - - - - -
D4 [mm] 29 29 29 29 29 29 29 29 29 29 29 29
D6 [mm] 37 37 37 37 37 37 37 37 37 37 37 37
L9 [mm] 24 24 24 24 24 24 24 24 24 24 24 24
95
T
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
(5)
Ø11
,5h8
15 10 20 10
5
Thread length
10
7
Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
1432
/5.1
2.35
5.39
7
1432
/5.1
2.16
0.23
0
1432
/5.1
2.51
0.58
0
2432
/5.1
2.35
5.39
7
2432
/5.1
2.16
0.23
0
2432
/5.1
2.51
0.58
0
2442
/10.
12.3
55.3
97
2442
/10.
12.1
60.2
30
2442
/10.
12.5
10.5
80
2442
/10.
12.3
55.3
97
2442
/10.
12.1
60.2
30
2442
/10.
12.5
10.5
80
A B B A B B A B B A B B
5 5 5 5 5 5 10 10 10 10 10 10
12 12 12 12 12 12 12 12 12 12 12 12
300 100 450 300 100 450 300 100 450 300 100 450
3 3 3 5 5 5 2 + 2 2+ 2 2 + 2 3 + 3 3 + 3 3 + 3
2 2 2 2 2 2 2.5 2.5 2.5 2.5 2.5 2.5
3200 3200 3200 5100 5100 5100 5300 5300 5300 7700 7700 7700
3900 3900 3900 6900 6900 6900 6400 6400 6400 10000 10000 10000
0.02 0.02 0.02 0.02 0.02 0.02 0.03 0.03 0.03 0.03 0.03 0.03
1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
39 39 39 25 25 25 20 20 20 30 30 30
22 22 22 24 24 24 24 24 24 24 24 24
- - - 7 7 7 9 9 9 9 9 9
29 29 29 32 32 32 32 32 32 32 32 32
37 37 37 40 40 40 40 40 40 40 40 40
24 24 24 26 26 26 26 26 26 26 26 26
96
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
16 (P=2:12)16 (P 2:12))
555
LP
keyway 1.9 dpkeyway 1 9 dpLZ
DZ
10LA
M18x1
for pin wrench Ø3
DAA
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1132: Nut with connecting thread without wipers
N O M I N A L D I A M E T E R 12 m mRolled execution with standard bearing journal T7 - T10
Series 1234, 1132
C Y L I N D R I C A L N U T■ Series 1234: Cylindrical nut without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1234
/1.1
2.35
5.39
7
1234
/1.1
2.16
0.23
0
1234
/1.1
2.51
0.58
0
1234
/2.1
2.35
5.39
7
1234
/2.1
2.16
0.23
0
1234
/2.1
2.51
0.58
0
1234
/3.1
2.35
5.39
7
1234
/3.1
2.16
0.23
0
1234
/3.1
2.51
0.58
0
1234
/4.1
2.35
5.39
7
1234
/4.1
2.16
0.23
0
1234
/4.1
2.51
0.58
0
1234
/5.1
2.35
5.39
7
Shaft style A B B A B B A B B A B B A
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4 5
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450 300
Ball circles i 3 3 3 3 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2
Dynamic load capacity Ca [N] 1300 1300 1300 2300 2300 2300 3300 3300 3300 3300 3300 3300 3200
Static load capacity C0a [N] 2200 2200 2200 3100 3100 3100 3900 3900 3900 3900 3900 3900 3900
Max. axial play [mm] with backlash 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
Max. friction torque [Ncm] (preloaded nut) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
Nut length LZ / LA [mm] 17 17 17 19 19 19 26 26 26 22 22 22 26
Nut diameter Dzh6 / DA [mm] 19 19 19 19 19 19 19 19 19 19 19 19 19
LP [mm] 2.5 2.5 2.5 1.5 1.5 1.5 5 5 5 3.5 3.5 3.5 5
97
T
■ Shaft style A
■ Shaft style B
1234
/5.1
2.16
0.23
0
1234
/5.1
2.51
0.58
0
1132
/1.1
2.35
5.39
7
1132
/1.1
2.16
0.23
0
1132
/1.1
2.51
0.58
0
1132
/2.1
2.35
5.39
7
1132
/2.1
2.16
0.23
0
1132
/2.1
2.51
0.58
0
1132
/3.1
2.35
5.39
7
1132
/3.1
2.16
0.23
0
1132
/3.1
2.51
0.58
0
1132
/4.1
2.35
5.39
7
1132
/4.1
2.16
0.23
0
1132
/4.1
2.51
0.58
0
1132
/5.1
2.35
5.39
7
1132
/5.1
2.16
0.23
0
1132
/5.1
2.51
0.58
0B B A B B A B B A B B A B B A B B
5 5 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5
12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12
100 450 300 100 450 300 100 450 300 100 450 300 100 450 300 100 450
3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
2 2 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2 2 2 2
3200 3200 1300 1300 1300 2300 2300 2300 3300 3300 3300 3300 3300 3300 3200 3200 3200
3900 3900 2200 2200 2200 3100 3100 3100 3900 3900 3900 3900 3900 3900 3900 3900 3900
0.02 0.02 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02
1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3) 1 (3)
26 26 24 24 24 29 29 29 36 36 36 33 33 33 36 36 36
19 19 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 20.5 22.5 22.5 22.5 22.5 22.5 22.5
5 5 - - - - - - - - - - - - - - -
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
(5)
Ø11
,5h8
15 10 20 10
5
Thread length
10
7
Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
Nuts shown in standard orientation. Select one nut from table.
98
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
M18x1
LD10
DD
6 56,51010
SW22
N O M I N A L D I A M E T E R 12 m mRolled execution with standard bearing journal T7 - T10
Series 1530
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1530: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1530
/1.1
2.35
5.39
7
1530
/1.1
2.16
0.23
0
1530
/1.1
2.51
0.58
0
1530
/2.1
2.35
5.39
7
1530
/2.1
2.16
0.23
0
1530
/2.1
2.51
0.58
0
1530
/3.1
2.35
5.39
7
1530
/3.1
2.16
0.23
0
1530
/3.1
2.51
0.58
0
1530
/4.1
2.35
5.39
7
1530
/4.1
2.16
0.23
0
1530
/4.1
2.51
0.58
0
Shaft style A B B A B B A B B A B B
Lead P [mm] 1 1 1 2 2 2 3 3 3 4 4 4
Nominal diameter dN [mm] 12 12 12 12 12 12 12 12 12 12 12 12
Nominal stroke [mm] 300 100 450 300 100 450 300 100 450 300 100 450
Ball circles i 2 2 2 2 2 2 2 2 2 2 2 2
Ball diameter [mm] 1 1 1 1.5 1.5 1.5 2 2 2 2 2 2
Dynamic load capacity Ca [N] 900 900 900 1600 1600 1600 2300 2300 2300 2300 2300 2300
Static load capacity C0a [N] 1500 1500 1500 2100 2100 2100 2600 2600 2600 2600 2600 2600
Max. preload [N] 50 50 50 80 80 80 80 80 80 80 80 80
Max. axial load [N] 40 40 40 70 70 70 70 70 70 70 70 70
Friction torque Tpr0 [Ncm] 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0 1.0-2.0
Nut length LD [mm] 49 49 49 49 49 49 49 49 49 49 49 49
Nut diameter DD [mm] 24 24 24 24 24 24 24 24 24 24 24 24
99
M8x
0,5
Ø6h
6
Ø8h
6 6
22 10 10
Ø8h
6
Thread length
Overall length
wrench flat 12
Ø11
,5h8
(5)
15 10 20 10
5
Thread length
10
7 Ø7,6x0,9
Ø8g
6
Overall length
Ø14
Ø10
g5
M10
x1
Ø8h
6
T
■ Shaft style A
■ Shaft style B
Please follow the advice on page 24/25.
1530
/5.1
2.35
5.39
7
1530
/5.1
2.16
0.23
0
1530
/5.1
2.51
0.58
0
A B B
5 5 5
12 12 12
300 100 450
2 2 2
2 2 2
2300 2300 2300
2600 2600 2600
80 80 80
70 70 70
1.0-2.0 1.0-2.0 1.0-2.0
49 49 49
24 24 24
100
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
LF1010
lube hole M6
L9
30°
D6D
330°°
D44D1-0,6D1-0,6D111
55,5Ø
1313
LF10
lube hole M6
L9
30°
D6D
330°°
D44D1-0,6
L3
D1-0,6D111
5,5Ø
13
N O M I N A L D I A M E T E R 16 m mRolled execution with standard bearing journal T7 - T10
Series 1432, 2442
F L A N G E N U T■ Series 1432: Nut with fl ange and standard wipers on
both ends
F L A N G E N U T■ Series 2442: Nut with fl ange and standard wipers on
both ends
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1432
/2.1
6.47
0.52
7
1432
/2.1
6.18
9.27
1
1432
/2.1
6.68
9.77
1
1432
/4.1
6.47
0.52
7
1432
/4.1
6.18
9.27
1
1432
/4.1
6.68
9.77
1
1432
/5.1
6.47
0.52
7
1432
/5.1
6.18
9.27
1
1432
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B
Lead P [mm] 2 2 2 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600
Ball circles i 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
Dynamic load capacity Ca [N] 2700 2700 2700 8000 8000 8000 9100 9100 9100
Static load capacity C0a [N] 4400 4400 4400 10300 10300 10300 10900 10900 10900
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04
Max. friction torque [Ncm] (preloaded nut) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
Nut length LF [mm] 32 32 32 38 38 38 44 44 44
Nut diameter D1g6 [mm] 25 25 25 28 28 28 28 28 28
L3 [mm] - - - - - - - - -
D4 [mm] 35 35 35 38 38 38 38 38 38
D6 [mm] 44 44 44 48 48 48 48 48 48
L9 [mm] 29 29 29 31 31 31 31 31 31
101
Ø12
h6
M12
x1
Ø10
h6
Ø12
h6
6
12 32 13
Thread length
Overall length
wrench flat 13
(5)
Ø10
h6
M12
x1
Ø12
g5
Ø15
,5h8
8
15 10 20 10
5
12
Ø10
g6
Ø9,6x1,15
Thread length
Overall length
T
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
*Please specify the number of circles
2442
/10.
16.4
70.5
27*
2442
/10.
16.1
89.2
71*
2442
/10.
16.6
89.7
71*
2442
/10.
16.4
70.5
27*
2442
/10.
16.1
89.2
71*
2442
/10.
16.6
89.7
71*
2442
/16.
16.4
70.5
27
2442
/16.
16.1
89.2
71
2442
/16.
16.6
89.7
71
2442
/20.
16.4
70.5
27
2442
/20.
16.1
89.2
71
2442
/20.
16.6
89.7
71
2442
/30.
16.4
70.5
27
2442
/30.
16.1
89.2
71
2442
/30.
16.6
89.7
71
A B B A B B A B B A B B A B B
10 10 10 10 10 10 16 16 16 20 20 20 30 30 30
16 16 16 16 16 16 16 16 16 16 16 16 16 16 16
400 100 600 400 100 600 400 100 600 400 100 600 400 100 600
3 + 3 3 + 3 3 + 3 5 + 5 5 + 5 5 + 5 2 + 2 2 + 2 2 + 2 2 + 2 2 + 2 2 + 2 0.5 + 0.5 0.5 + 0.5 0.5 + 0.5
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
17700 17700 17700 28300 28300 28300 12100 12100 12100 11700 11700 11700 2100 2100 2100
25000 25000 25000 43100 43100 43100 16500 16500 16500 16100 16100 16100 2300 2300 2300
0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04
1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
32 32 32 52 52 52 31 31 31 38 38 38 26 26 26
32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
12 12 12 12 12 12 10 10 10 10 10 10 12 12 12
42 42 42 42 42 42 42 42 42 42 42 42 42 42 42
52 52 52 52 52 52 52 52 52 52 52 52 52 52 52
40 40 40 40 40 40 40 40 40 40 40 40 40 40 40
102
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
5555
1616
LP
y y pkeyway 1.9 dpLZ
DZD
N O M I N A L D I A M E T E R 16 m mRolled execution with standard bearing journal T7 - T10
Series 1234, 1132
C Y L I N D R I C A L N U T■ Series 1234: Cylindrical nut without wipers
10LA
M22x1
for pin wrench Ø3
DAD
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1132: Nut with connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1234
/2.1
6.47
0.52
7
1234
/2.1
6.18
9.27
1
1234
/2.1
6.68
9.77
1
1234
/4.1
6.47
0.52
7
1234
/4.1
6.18
9.27
1
1234
/4.1
6.68
9.77
1
1234
/5.1
6.47
0.52
7
1234
/5.1
6.18
9.27
1
1234
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B
Lead P [mm] 2 2 2 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600
Ball circles i 3 3 3 3 3 3 3 3 3
Ball diameter [mm] 1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
Dynamic load capacity Ca [N] 2700 2700 2700 8000 8000 8000 9100 9100 9100
Static load capacity C0a [N] 4400 4400 4400 10300 10300 10300 10900 10900 10900
Max. axial play [mm] with backlash 0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04
Max. friction torque [Ncm] (preloaded nut) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
Nut length LZ / LA [mm] 19 19 19 21 21 21 27 27 27
Nut diameter DZh6 / DA [mm] 28 28 28 28 28 28 28 28 28
LP [mm] 1.5 1.5 1.5 2.5 2.5 2.5 5.5 5.5 5.5
103
T
■ Shaft style A
■ Shaft style B
Nuts shown in standard orientation. Select one nut from table.
1132
/2.1
6.47
0.52
7
1132
/2.1
6.18
9.27
1
1132
/2.1
6.68
9.77
1
1132
/4.1
6.47
0.52
7
1132
/4.1
6.18
9.27
1
1132
/4.1
6.68
9.77
1
1132
/5.1
6.47
0.52
7
1132
/5.1
6.18
9.27
1
1132
/5.1
6.68
9.77
1
A B B A B B A B B
2 2 2 4 4 4 5 5 5
16 16 16 16 16 16 16 16 16
400 100 600 400 100 600 400 100 600
3 3 3 3 3 3 3 3 3
1.5 1.5 1.5 3 3 3 3.5 3.5 3.5
2700 2700 2700 8000 8000 8000 9100 9100 9100
4400 4400 4400 10300 10300 10300 10900 10900 10900
0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04
1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4) 1.4 (4)
29 29 29 38 38 38 43 43 43
25.5 25.5 25.5 28.5 28.5 28.5 28.5 28.5 28.5
- - - - - - - - -
Ø12
h6
M12
x1
Ø10
h6
Ø12
h6
6
12 32 13
Thread length
Overall length
wrench flat 13
(5)
Ø10
h6
M12
x1
Ø12
g5
Ø15
,5h8
8
15 10 20 10
5
12
Ø10
g6
Ø9,6x1,15
Thread length
Overall length
104
Tr a n s p o r t b a l l s c r e w s 8 - 1 6 m m
M22x12
LA10
DAA
8,58,51010
wrench flat 30
N O M I N A L D I A M E T E R 16 m mRolled execution with standard bearing journal T7 - T10
Series 1530
N U T W I T H C O N N E C T I N G T H R E A D■ Series 1530: Spring preloaded double nut in housing with
connecting thread without wipers
Technical data
Numbering system see page 52
(Please specify the accuracy class)
1530
/2.1
6.47
0.52
7
1530
/2.1
6.18
9.27
1
1530
/2.1
6.68
9.77
1
1530
/4.1
6.47
0.52
7
1530
/4.1
6.18
9.27
1
1530
/4.1
6.68
9.77
1
1530
/5.1
6.47
0.52
7
1530
/5.1
6.18
9.27
1
1530
/5.1
6.68
9.77
1
Shaft style A B B A B B A B B
Lead P [mm] 2 2 2 4 4 4 5 5 5
Nominal diameter dN [mm] 16 16 16 16 16 16 16 16 16
Nominal stroke [mm] 400 100 600 400 100 600 400 100 600
Ball circles i 2 2 2 2 2 2 2 2 2
Ball diameter [mm] 1.5 1.5 1.5 2 2 2 2.5 2.5 2.5
Dynamic load capacity Ca [N] 1900 1900 1900 2700 2700 2700 3500 3500 3500
Static load capacity C0a [N] 2900 2900 2900 3600 3600 3600 4300 4300 4300
Max. preload [N] 120 120 120 120 120 120 150 150 150
Max. axial load [N ] 100 100 100 100 100 100 130 130 130
Friction torque Tpr0 [Ncm] 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0 1.5-3.0
Nut length LD [mm] 57 57 57 57 57 57 57 57 57
Nut diameter DD [mm] 33 33 33 33 33 33 33 33 33
105
Ø12
h6
M12
x1
Ø10
h6
Ø12
h6
6
12 32 13
Thread length
Overall length
wrench flat 13
(5)
Ø10
h6
M12
x1
Ø12
g5
Ø15
,5h8
8
15 10 20 10
5
12
Ø10
g6
Ø9,6x1,15
Thread length
Overall length
T
■ Shaft style A
■ Shaft style B
Please follow the advice on page 24/25.
TORINODirezione Generale - Headquarter:
Via Mappano, 17 - 10071 Borgaro T.se (TO)T +39 011 451 8611 (centr. r.a.) - F +39 011 470 4891
setec.to@setec-group.it
MILANOVia Meccanica, 5
20026 Novate (MI) - Z. I. VialbaT +39 02 356 0990 - 382 01 590 (r.a.)
F +39 02 356 0943setec.mi@setec-group.it
PADOVAVia Secchi, 8135136 Padova
T +39 049 872 5983F +39 049 856 0965
setec.pd@setec-group.it
www.setec-group.it
GUIDE LINEARIDI PRECISIONEPRECISION LINEAR GUIDEWAYS
HIW
IN G
W E
NG
REV
02
BOLOGNAVia Del Lavoro, 6/A40051 Altedo (BO)
T +39 051 871 949 (3 linee r.a.)F +39 051 870 329
setec.bo@setec-group.it
FIRENZEVia Galileo Galilei, 3
50015 Bagno a Ripoli - Grassina (FI)T +39 055 643 261F +39 055 646 6614
setec.fi@setec-group.it
TORINODirezione Generale - Headquarter:
Via Mappano, 17 - 10071 Borgaro T.se (TO)T +39 011 451 8611 (centr. r.a.) - F +39 011 470 4891
setec.to@setec-group.it
MILANOVia Meccanica, 5
20026 Novate (MI) - Z. I. VialbaT +39 02 356 0990 - 382 01 590 (r.a.)
F +39 02 356 0943setec.mi@setec-group.it
PADOVAVia Secchi, 8135136 Padova
T +39 049 872 5983F +39 049 856 0965
setec.pd@setec-group.it
www.setec-group.it
GUIDE LINEARIDI PRECISIONEPRECISION LINEAR GUIDEWAYS
HIW
IN G
W E
NG
REV
02
BOLOGNAVia Del Lavoro, 6/A40051 Altedo (BO)
T +39 051 871 949 (3 linee r.a.)F +39 051 870 329
setec.bo@setec-group.it
FIRENZEVia Galileo Galilei, 3
50015 Bagno a Ripoli - Grassina (FI)T +39 055 643 261F +39 055 646 6614
setec.fi@setec-group.it
TORINODirezione Generale - Headquarter:
Via Mappano, 17 - 10071 Borgaro T.se (TO)T +39 011 451 8611 (centr. r.a.) - F +39 011 470 4891
setec.to@setec-group.it
MILANOVia Meccanica, 5
20026 Novate (MI) - Z. I. VialbaT +39 02 356 0990 - 382 01 590 (r.a.)
F +39 02 356 0943setec.mi@setec-group.it
PADOVAVia Secchi, 8135136 Padova
T +39 049 872 5983F +39 049 856 0965
setec.pd@setec-group.it
www.setec-group.it
GUIDE LINEARIDI PRECISIONEPRECISION LINEAR GUIDEWAYS
HIW
IN G
W E
NG
REV
02
BOLOGNAVia Del Lavoro, 6/A40051 Altedo (BO)
T +39 051 871 949 (3 linee r.a.)F +39 051 870 329
setec.bo@setec-group.it
FIRENZEVia Galileo Galilei, 3
50015 Bagno a Ripoli - Grassina (FI)T +39 055 643 261F +39 055 646 6614
setec.fi@setec-group.it
TORINODirezione Generale - Headquarter:
Via Mappano, 17 - 10071 Borgaro T.se (TO)T +39 011 451 8611 (centr. r.a.) - F +39 011 470 4891
setec.to@setec-group.it
MILANOVia Meccanica, 5
20026 Novate (MI) - Z. I. VialbaT +39 02 356 0990 - 382 01 590 (r.a.)
F +39 02 356 0943setec.mi@setec-group.it
PADOVAVia Secchi, 8135136 Padova
T +39 049 872 5983F +39 049 856 0965
setec.pd@setec-group.it
www.setec-group.it
GUIDE LINEARIDI PRECISIONEPRECISION LINEAR GUIDEWAYS
HIW
IN G
W E
NG
REV
02
BOLOGNAVia Del Lavoro, 6/A40051 Altedo (BO)
T +39 051 871 949 (3 linee r.a.)F +39 051 870 329
setec.bo@setec-group.it
FIRENZEVia Galileo Galilei, 3
50015 Bagno a Ripoli - Grassina (FI)T +39 055 643 261F +39 055 646 6614
setec.fi@setec-group.it
ww
w.d
art-s
as.it ISOMOVE
®ATTUATORI MECCANICIMECHANICAL ACTUATORSISO 15552 : 2004
ISO
MO
VE
ATTU
ATO
RI M
ECCA
NIC
I/M
ECH
AN
ICAL
ACT
UAT
ORS
ISOMOVE
Cert. n° EMS-2240/S
11 /
201
0
TORINODirezione Generale e Stabilimento di Produzione - Headquarter and Production Plant :
Via Mappano, 17 - 10071 Borgaro T.se (TO)T +39 011 451 8611 (centr. r.a.) - F +39 011 470 4891
setec.to@setec-group.it
www.setec-group.it
MILANOVia Meccanica, 5
20026 Novate (MI) - Z. I. VialbaT +39 02 356 0990 - 382 01 590 (r.a.)
F +39 02 356 0943setec.mi@setec-group.it
PADOVAVia Secchi, 8135136 Padova
T +39 049 872 5983 - F +39 049 856 0965setec.pd@setec-group.it
BOLOGNAVia Del Lavoro, 6/A40051 Altedo (BO)
T +39 051 871 949 (3 linee r.a.)F +39 051 870 329
setec.bo@setec-group.it
FIRENZEVia Galileo Galilei, 3
50015 Bagno a Ripoli - Grassina (FI)T +39 055 643 261 - F +39 055 646 6614
setec.fi@setec-group.it
Distribuito da / Distributed by:
Copertina+dorsetto ISOMOVE 3:Copertina+dorsetto ISOMOVE 3 6-11-2010 11:01 Pagina 1
top related