modul 09 clutches, brakes, couplings and flywheel part i
Post on 23-Mar-2022
2 Views
Preview:
TRANSCRIPT
1 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.01. Introduction
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
2 MS3111 Elemen MesinMAK © 2021
Modul 09 Clutches, Brakes, Couplings and Flywheel Part I
IntroductionSegment
1
Static Analysis of Clutches
and Brakes
Segment
2
Internal Expanding Rim
Clutches and Brakes
Segment
3
External Contracting Rim
Clutches and Brakes
Segment
4
Band-Type Clutches and
Brakes
Segment
5
Frictional-Contact Axial
Clutches
Segment
6
Disk BrakesSegment
7
Cone Clutches and Brakes
Segment
8
3 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.01. Introduction
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
4 MS3111 Elemen MesinMAK © 2021
Representation
𝜔2𝜔1
𝐼1𝐼2
Brakes or Clutch 𝜔 = angular velocity
𝐼 = Inertia
𝑇i, 𝜃i
Flywheel
𝐼, 𝜃
𝑇o, 𝜃o
𝑇 = Torque𝜃 = angular displacement
5 MS3111 Elemen MesinMAK © 2021
Performance Analysis
1. The actuating force (gaya aktivasi)
2. The torque transmitted (torsi diteruskan)
3. The energy loss (rugi-rugi)
4. The temperature rise (kenaikan temperatur)
6 MS3111 Elemen MesinMAK © 2021
Various Types of Devices
1. Rim types with internal expanding shoes
2. Rim type with external contracting shoes
3. Band types
4. Disk or axial types
5. Cone types
6. Miscellaneous types
7 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.02. Static Analysis of Clutches and Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
8 MS3111 Elemen MesinMAK © 2021
General procedures of analysis steps.
1. Estimate or determine the distribution of pressure on the frictional surfaces.
2. Find a relation between the maximum pressure and the pressure at any point.
3. Apply the conditions of static equilibrium to find the actuating force, the torque, and the support reactions.
9.1. Static Analysis of Clutches and Brakes
Figure 16–2 A common doorstop.
9 MS3111 Elemen MesinMAK © 2021
• A normal pressure distribution 𝒑(𝒖) is shown under the friction pad as a function of position 𝑢, taken from the right edge of the pad.
• Distribution of shearing frictional traction is on the surface, of intensity 𝑓𝑝(𝑢), in the direction of the motion of the floor relative to the pad, where 𝑓is the coefficient of friction.
10 MS3111 Elemen MesinMAK © 2021
The net force in the y-direction:
The moment about C from the pressure:
𝑁 = 𝑤2න0
𝑤1
𝑝 𝑢 𝑑𝑢 = 𝑝𝑎𝑣𝑤1𝑤2
𝑤2න0
𝑤1
𝑝 𝑢 𝑢𝑑𝑢 = ത𝑢𝑤2න0
𝑤1
𝑝 𝑢 𝑑𝑢 = 𝑝𝑎𝑣𝑤1𝑤2 ത𝑢
11 MS3111 Elemen MesinMAK © 2021
We sum the forces in the x-direction to obtain
𝐹𝑥 = 0 𝑅𝑥 ∓𝑤2න0
𝑤1
𝑓𝑝 𝑢 𝑑𝑢 = 0
where − or + is for rightward or leftward relative motion of the floor, respectively.
• Assuming f constant, solving for Rx gives
𝑅𝑥 = ±𝑤2න0
𝑤1
𝑓𝑝 𝑢 𝑑𝑢 = ±𝑓𝑤1𝑤2𝑝𝑎𝑣
12 MS3111 Elemen MesinMAK © 2021
• Summing the forces in the y-direction gives
from which
for either direction.
𝐹𝑦 = 0 −𝐹 + 𝑅𝑦 +𝑤2න0
𝑤1
𝑝 𝑢 𝑑𝑢 = 0
𝑅𝑦 = 𝐹 − 𝑤2න0
𝑤1
𝑝 𝑢 𝑑𝑢 = 𝐹 − 𝑝𝑎𝑣𝑤1𝑤2
13 MS3111 Elemen MesinMAK © 2021
Summing moments about the pin located at A we have
𝑀𝐴 = 0
𝐹𝑏 − 𝑤2න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 ∓ 𝑎𝑓𝑤2න0
𝑤1
𝑝 𝑢 𝑑𝑢 = 0
A brake shoe is self-energizing if its moment sense helps set the brake, self-deenergizing if the moment resists setting the brake. Continuing:
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 ± 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢
14 MS3111 Elemen MesinMAK © 2021
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 ± 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢
Can F be equal to or less than zero? Only during rightward motion of the floor when the expression in brackets in Eq. (e) is equal to or less than zero. We set the brackets to zero or less:
න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 − 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢 ≤ 0
from which:
𝑓𝑐𝑟 ≥1
𝑎
0𝑤1 𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢
0𝑤1 𝑝 𝑢 𝑑𝑢
=1
𝑎
𝑐 0𝑤1 𝑝 𝑢 𝑑𝑢 + 0
𝑤1 𝑝 𝑢 𝑢𝑑𝑢
0𝑤1 𝑝 𝑢 𝑑𝑢
𝑓𝑐𝑟 ≥𝑐 + ത𝑢
𝑎 where ത𝑢 is the distance of the center of pressure from the right edge of the pad.
15 MS3111 Elemen MesinMAK © 2021
Some remarks:
➢The conclusion that a self-acting or self-locking phenomenon is present and is independent of our knowledge of the normal pressure distribution 𝑝(𝑢).
➢Our ability to find the critical value of the coefficient of friction 𝑓𝑐𝑟 is dependent on our knowledge of 𝑝(𝑢), from which we derive ത𝑢.
16 MS3111 Elemen MesinMAK © 2021
EXAMPLE 16–1
The doorstop depicted in Fig. 16–2a has the following dimensions: a = 4 in, b = 2 in, c = 1.6 in, w1 = 1 in, w2 = 0.75 in, where w2 is the depth of the pad into the plane of the paper.a) For a leftward relative movement of the floor, an actuating force F of 10
lbf, a coefficient of friction of 0.4, use a uniform pressure distribution pav, find Rx , Ry , pav, and the largest pressure pa.
b) Repeat part a for rightward relative movement of the floor.c) Model the normal pressure to be the “crush” of the pad, much as if it
were composed of many small helical coil springs. Find Rx , Ry , pav, and pa for leftward relative movement of the floor and other conditions as in part a.
d) For rightward relative movement of the floor, is the doorstop a self-acting brake?
17 MS3111 Elemen MesinMAK © 2021
𝑅𝑥 = 𝑓𝑤1𝑤2𝑝𝑎𝑣 = 0.4 1 0.75 𝑝𝑎𝑣 = 0.3𝑝𝑎𝑣
Solution
Leftward:
𝑅𝑦 = 𝐹 − 𝑝𝑎𝑣𝑤1𝑤2 = 10 − 1 0.75 𝑝𝑎𝑣 = 10 − 0.75𝑝𝑎𝑣
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 ± 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢
𝐹 =𝑤2
𝑏න0
1
𝑝𝑎𝑣 𝑐 + 𝑢 𝑑𝑢 + 𝑎𝑓න0
1
𝑝𝑎𝑣𝑑𝑢
𝐹 =𝑤2
𝑏𝑝𝑎𝑣𝑐 න
0
1
𝑑𝑢 + 𝑝𝑎𝑣න0
1
𝑢𝑑𝑢 + 𝑎𝑓𝑝𝑎𝑣න0
1
𝑑𝑢
𝐹 =𝑤2𝑝𝑎𝑣𝑏
𝑐 + 0.5 + 𝑎𝑓
10 =(0.75)𝑝𝑎𝑣
21.6 + 0.5 + 4(0.4)
𝑝𝑎𝑣 = 7.207 𝑝𝑠𝑖
= 0.3 7.207 = 2.162 𝑙𝑏𝑓
= 10 − 0.75 7.207= 4.595 𝑙𝑏𝑓
Answer
Answer
Answer
18 MS3111 Elemen MesinMAK © 2021
b) Repeat part a for rightward relative movement of the floor.
𝑅𝑥 = −𝑓𝑤1𝑤2𝑝𝑎𝑣 = −0.4 1 0.75 𝑝𝑎𝑣 = −0.3𝑝𝑎𝑣
𝑅𝑦 = 𝐹 − 𝑝𝑎𝑣𝑤1𝑤2 = 10 − 1 0.75 𝑝𝑎𝑣 = 10 − 0.75𝑝𝑎𝑣
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 ± 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢
𝐹 =𝑤2
𝑏න0
1
𝑝𝑎𝑣 𝑐 + 𝑢 𝑑𝑢 − 𝑎𝑓න0
1
𝑝𝑎𝑣𝑑𝑢
𝐹 =𝑤2
𝑏𝑝𝑎𝑣𝑐 න
0
1
𝑑𝑢 + 𝑝𝑎𝑣න0
1
𝑢𝑑𝑢 − 𝑎𝑓𝑝𝑎𝑣න0
1
𝑑𝑢
𝐹 =𝑤2𝑝𝑎𝑣𝑏
𝑐 + 0.5 − 𝑎𝑓
10 =(0.75)𝑝𝑎𝑣
21.6 + 0.5 − 4(0.4)
𝑝𝑎𝑣 = 53.33 𝑝𝑠𝑖
= 0.3 53.33 = −16 𝑙𝑏𝑓
= 10 − 0.75 5.33 = −30 𝑙𝑏𝑓
Answer
Answer
Answer
19 MS3111 Elemen MesinMAK © 2021
c) Model the normal pressure to be the “crush” of the pad, much as if it were composed of many small helical coil springs. Find Rx , Ry , pav, and pa for leftward relative movement of the floor and other conditions as in part a.
From similar triangles 𝑦1𝑟1∆𝜙
=𝑐
𝑟1
𝑦2𝑟2∆𝜙
=𝑐 + 𝑤1𝑟2
𝑦1 = 𝑐∆𝜙 𝑦2 = (𝑐 + 𝑤1)∆𝜙
This means that y is directly proportional to the horizontal distance from the pivot point A; that is, 𝑦 = 𝐶1𝜈, where 𝐶1 is a constant
Assuming the pressure is directly proportional to deformation, then 𝑝 𝜈 = 𝐶2𝜈, where 𝐶2 is a constant. In terms of 𝑢, the pressure is 𝑝 𝑢 = 𝐶2 𝑐 + 𝑢 = 𝐶2 1.6 + 𝑢
20 MS3111 Elemen MesinMAK © 2021
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐 + 𝑢 𝑑𝑢 + 𝑎𝑓න0
𝑤1
𝑝 𝑢 𝑑𝑢
𝐹 =𝑤2
𝑏න0
𝑤1
𝑝 𝑢 𝑐𝑑𝑢 + න0
𝑤1
𝑝 𝑢 𝑢𝑑𝑢 + 𝑎𝑓න0
𝑤1
𝑝(𝑢)𝑑𝑢
𝑝 𝑢 = 𝐶2 𝑐 + 𝑢 = 𝐶2 1.6 + 𝑢
𝐹 =0.75
2න0
1
𝐶2 1.6 + 𝑢 (1.6)𝑑𝑢 + න0
1
𝐶2 1.6 + 𝑢 𝑢𝑑𝑢 + 𝑎𝑓න0
1
𝐶2 1.6 + 𝑢 𝑑𝑢
10 = 0.375𝐶2 1.6 + 0.5 1.6 + (0.8 + 0.3333) + 4(0.4)(1.6 + 0.5)
𝐶2 = 3.396 𝑝𝑠𝑖/𝑖𝑛 𝑝 𝑢 = 3.396 1.6 + 𝑢
The average pressure is given by
𝑝𝑎𝑣 =1
𝑤1න0
𝑤1
𝑝 𝑢 𝑑𝑢 =1
1න0
1
3.396(1.6 + 𝑢)𝑑𝑢 = 3.396 1.6 + 0.5 = 7.132 𝑝𝑠𝑖
The maximum pressure occurs at 𝑢 = 1 𝑖𝑛, and is 𝑝𝑎 = 3.396 1.6 + 1 = 8.83 𝑝𝑠𝑖
𝑅𝑥 = 0.3𝑝𝑎𝑣 = 0.3 7.132 = 2.139 𝑙𝑏𝑓 𝑅𝑦 = 10 − 0.75𝑝𝑎𝑣 = 10 − 0.75 7.132 = 4.652 𝑙𝑏𝑓
The reaction at support:
21 MS3111 Elemen MesinMAK © 2021
d) For rightward relative movement of the floor, is the doorstop a self-acting brake?
To evaluate ത𝑢 we need to evaluate two integrations
න0
𝑐
𝑝 𝑢 𝑢𝑑𝑢 = න0
1
3.396(1.6 + 𝑢)𝑢𝑑𝑢 = 3.396 0.8 + 0.3333 = 3.849 𝑙𝑏𝑓
න0
𝑐
𝑝 𝑢 𝑑𝑢 = න0
1
3.396(1.6 + 𝑢)𝑑𝑢 = 3.396 1.6 + 0.5 = 7.132 𝑙𝑏𝑓/𝑖𝑛
Thus, ത𝑢 =3.849
7.132= 0.5397 𝑖𝑛 𝑓𝑐𝑟 ≥
𝑐 + ത𝑢
𝑎𝑓𝑐𝑟 ≥
1.6 + 0.5397
4= 0.535
The doorstop friction pad does not have a high enough coefficient of friction to make the doorstop a self-acting brake. The configuration must change and/or the pad material specification must be changed to sustain the function of a doorstop.
22 MS3111 Elemen MesinMAK © 2021
23 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.03. Internal Expanding Rim Clutches and Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
24 MS3111 Elemen MesinMAK © 2021
9.2. Internal Expanding Rim Clutches & Brakes
(a) Clutch (b) BrakeFigure 16–3 (a) internal expanding centrifugal-acting rim clutch (b) internal expanding brake
25 MS3111 Elemen MesinMAK © 2021
❑ Depending upon the operating mechanism, such clutches are further classified as: expanding-ring, centrifugal, magnetic, hydraulic, and pneumatic.
❑ Internal-shoe rim expanding type consist of 3 elements:
• the mating frictional surface,
• the means of transmitting the torque to and from the surfaces,
• the actuating mechanism.
❑ The expanding-ring clutch is often used: in textile machinery, excavators, and machine tools.
❑ In braking systems, the internal-shoe or drum brake is used mostly for automotive applications.
26 MS3111 Elemen MesinMAK © 2021
Force Analysis▪ Let us consider the unit pressure p acting upon
an element of area of the frictional material
located at an angle from the hinge A.
▪ We designate the maximum pressure by pa
located at the angle a from the hinge pin A.
▪ The mechanical arrangement permits no pressure to be applied at the heel (point A) ➔the pressure at this point is assumed to be zero.
▪ In some designs the hinge pin is made movable to provide additional heel pressure.
In this case, as long shoe, the uniform distribution of pressure is not valid anymore !
p
Figure 16–5 The geometry associated with an arbitrary point on the shoe.
27 MS3111 Elemen MesinMAK © 2021
28 MS3111 Elemen MesinMAK © 2021
The following assumption are implied by the following analysis:
1. The pressure at any point on the shoe is assumed to be proportional to distance from the hinge pin, being zero at the heel.
2. The effect of centrifugal force has been neglected. In the case of brakes, the shoes are not rotating, and no centrifugal force exists. In clutch design, the effect of centrifugal force must be considered in writing the equations of static equilibrium.
3. The shoe is assumed to be rigid. Since this cannot be true, some deflection will occur, depending upon the load, pressure, and stiffness of the shoe. The resulting pressure distribution may be different from that which has been assumed.
4. The entire analysis has been based upon a constant coefficient of friction (does not vary with pressure). Actually, the coefficient may vary with a number of conditions including temperature, wear, and environment.
29 MS3111 Elemen MesinMAK © 2021
Step 1Make the assumption that the pressure at any point is proportional to the vertical distance from the hinge pin.
This vertical distance is proportional to sin➔ 𝑝 ≈ sin 𝜃 ⇒𝑝
sin 𝜃= 𝑐𝑜𝑛𝑠𝑡
Step 2
To find the pressure distribution on the periphery of the internal shoe, consider point B on the shoe.
As in Ex. 16–1, if the shoe deforms by an infinitesimal rotation Δ𝜙 about the pivot point A, deformation perpendicular to B is ℎΔ𝜙.
▪ From triangle AOB, ℎ = 2𝑟 sin( Τ𝜃 2), so
30 MS3111 Elemen MesinMAK © 2021
▪ The deformation perpendicular to the rim is ℎΔ𝜙 cos Τ𝜃 2 , which is
Thus, the deformation, and consequently the pressure, is proportional to sin 𝜃.
ℎΔ𝜙 cos Τ𝜃 2 = 2𝑟Δ𝜙 sin Τ𝜃 2 cos Τ𝜃 2 = 𝑟∆𝜙 sin 𝜃
𝑝
sin 𝜃=
𝑝𝑎sin 𝜃𝑎
𝑝 =𝑝𝑎
sin 𝜃𝑎sin 𝜃or
▪ In terms of the pressure at B and where the pressure is a maximum, this means
(a) (1)
31 MS3111 Elemen MesinMAK © 2021
▪ The useful characteristics of the previous pressure distribution are:
➢The pressure distribution is sinusoidal.
➢ If the shoe is short, the largest pressure on the shoe is 𝑝𝑎 occurring at the end of the shoe, 𝜃𝑎 .
➢ If the shoe is long, the largest pressure on the shoe is 𝑝𝑎 occurring at 𝜃𝑎 = 90° .
▪ In choosing friction material, the designer should think in terms of 𝑝𝑎 and not about the amplitude of the sinusoidal distribution that addresses locations off the shoe.
Figure 16–6
𝑝 =𝑝𝑎
sin 𝜃𝑎sin 𝜃
32 MS3111 Elemen MesinMAK © 2021
Figure 16–7Forces on the shoe
Drum’s rotation
Step 3
▪ At the angle from the hinge pin, there acts a differential normal force dN whose magnitude is.
where b is the face width of the friction material.
𝑑𝑁 = 𝑝𝑏𝑟𝑑𝜃 (b)
𝑝 =𝑝𝑎
sin 𝜃𝑎sin 𝜃
𝑑𝑁 =𝑝𝑎𝑏𝑟 sin 𝜃 𝑑𝜃
sin 𝜃𝑎(c)
▪ Substituting the value of the pressure, eq. (1), we find
33 MS3111 Elemen MesinMAK © 2021
𝒅𝑵
𝜃
𝑑𝑁 cos 𝜃
𝑑𝑁 sin 𝜃𝑓𝑑𝑁 cos 𝜃
𝑓𝑑𝑁 sin 𝜃
𝑭
𝑭𝒚
𝑭𝒙
Step 3 (continued)
▪ The normal force, dN and other forces act on the friction material can be decomposed into horizontal and vertical component, as shown on Fig. 16–7.
▪ The actuating force F can be found by using the condition that the summation of the moments about the hinge pin is zero.
Figure 16–7Forces on the shoe
34 MS3111 Elemen MesinMAK © 2021
Figure 16–7Forces on the shoe
(3)𝑀𝑁 = න𝑑𝑁 𝑎 sin 𝜃 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃
The moment arm of the normal force 𝑑𝑁 about the pin is 𝑎 sin 𝜃. Designating the moment of the normal forces by 𝑀𝑁 and summing these about the hinge pin give
𝐹 =𝑀𝑁 −𝑀𝑓
𝑐(4)
The actuating force F must balance these two moments:
The frictional forces have a moment arm about the
pin of 𝑟 − 𝑎 cos 𝜃 . The moment 𝑀𝑓 of these frictional forces is:
𝑀𝑓 = න𝑓𝑑𝑁 𝑟 − 𝑎 cos 𝜃 =𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎න
𝜃1
𝜃2
sin 𝜃 𝑟 − 𝑎 cos 𝜃 𝑑𝜃
(2)
35 MS3111 Elemen MesinMAK © 2021
Step 3 (continued)
▪ If we make MN = Mf , self-locking is obtained, and no actuating force is required.
▪ To obtain self-energizing condition, the dimension a in figure must be such that
(5)𝑀𝑁 > 𝑀𝑓
▪ The torque 𝑇 applied to the drum by the brake shoe is the sum of the frictional forces 𝑓𝑑𝑁 times the radius of the drum:
𝑇 = න𝑓𝑟 𝑑𝑁 =𝑓𝑝𝑎𝑏𝑟
2
sin 𝜃𝑎න
𝜃1
𝜃2
sin 𝜃 𝑑𝜃 =𝑓𝑝𝑎𝑏𝑟
2 cos 𝜃1 − cos 𝜃2sin 𝜃𝑎
(6)
Braking capacity
36 MS3111 Elemen MesinMAK © 2021
Step 3 (continued)
▪ The hinge pin reactions are found by taking a summation of the horizontal and vertical forces, thus we have
(d)𝑅𝑥 = න𝑑𝑁 cos 𝜃 − න𝑓𝑑𝑁 sin 𝜃 − 𝐹𝑥 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐴 − 𝑓𝐵 − 𝐹𝑥
(e)𝑅𝑦 = න𝑑𝑁 sin 𝜃 + න𝑓𝑑𝑁 cos 𝜃 − 𝐹𝑦 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐵 + 𝑓𝐴 − 𝐹𝑦
𝐴 = න
𝜃1
𝜃2
sin 𝜃 cos 𝜃 𝑑𝜃 = อ1
2sin2 𝜃
𝜃1
𝜃2
𝐵 = න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃 = อ𝜃
2−1
4sin 2 𝜃
𝜃1
𝜃2
where:
37 MS3111 Elemen MesinMAK © 2021
Step 3 (continued)
▪ The direction of the frictional forces is reversed if the rotation is reversed. Thus, for counterclockwise rotation of drum, the actuating force become
𝐹 =𝑀𝑁 +𝑀𝑓
𝑐(7)
▪ Since both moments have the same sense, the self-energizing effect is lost and also self-locking.
38 MS3111 Elemen MesinMAK © 2021
Step 3 (continued)
(g)
𝑅𝑦 = න𝑑𝑁 sin 𝜃 − න𝑓𝑑𝑁 cos 𝜃 − 𝐹𝑦
=𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐵 − 𝑓𝐴 − 𝐹𝑦
(f)𝑅𝑥 = න𝑑𝑁 cos 𝜃 + න𝑓𝑑𝑁 sin 𝜃 − 𝐹𝑥
=𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐴 + 𝑓𝐵 − 𝐹𝑥
For counterclockwise
rotation
▪ Also, for counterclockwise rotation the signs of frictional terms in the equilibrium for the pin reactions change, and equation (d) and (e) become:
39 MS3111 Elemen MesinMAK © 2021
Figure 16–8Brake with internal expanding shoes; dimensions in millimeters.
EXAMPLE 16–2
The brake shown in Fig. 8 has 300 mm in diameter and is actuated by a mechanism that exerts the same force F on each shoe. The shoes are identical and have a face width of 32 mm. The lining is a molded asbestos having a coefficient of friction of 0.32 and a pressure limitation of 1000 kPa. Estimate the maximum
(a) Actuating force F.(b) Braking capacity.(c) Hinge-pin reactions.
40 MS3111 Elemen MesinMAK © 2021
Known
𝑏 = 32 𝑚𝑚𝑓 = 0.32𝑝𝑎 = 1000 𝑘𝑃𝑎
𝜃1 = 0°𝜃2 = 126°𝜃𝑎 = 90°
𝑎 = 1122 + 502 = 122.7 𝑚𝑚
41 MS3111 Elemen MesinMAK © 2021
𝜃1 = 0°
𝜃2 = 126°
𝜃𝑎 = 90°
𝑑𝑁
𝑓𝑑𝑁
Solution
𝑀𝑓 =𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎න
0
𝜃2
sin 𝜃 𝑟 − 𝑎 cos 𝜃 𝑑𝜃
The moment of the frictional force :
=𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎−𝑟 cos 𝜃 0
𝜃2 − 𝑎1
2sin2𝜃
0
𝜃2
=𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝑟 −𝑟 cos 𝜃2 −
𝑎
2sin2𝜃2
=(0.32)(1000 × 103) (0.032)(0.150)
sin 90°
× 0.150−0.150 cos 126° −0.1227
2sin2126°
= 304 𝑁𝑚
(a) Actuating force F.
42 MS3111 Elemen MesinMAK © 2021
The moment of the normal forces
𝑀𝑁 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
0
𝜃2
sin2 𝜃 𝑑𝜃 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎
𝜃
2−1
4sin 2𝜃
0
𝜃2
=𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎
𝜃22−1
4sin 2𝜃2
=(1000 × 103)(0.032)(0.150)(0.1227)
sin 90°
126° ×𝜋
180°2
−1
4sin 2(126°)
= 788 𝑁𝑚
The actuating force is
𝐹 =𝑀𝑁 −𝑀𝑓
𝑐=788 − 304
100 + 112= 2.28 𝑘𝑁 Answer (a)
43 MS3111 Elemen MesinMAK © 2021
(b) Braking capacity.
𝑇𝑅 =𝑓𝑝𝑎𝑏𝑟
2 cos 𝜃1 − cos 𝜃2sin 𝜃𝑎
=(0.32)(1000 × 103)(0.032) (0.150)2 cos 0 − cos 126°
sin 90= 366 𝑁𝑚
The torque contributed by the left-hand shoe cannot be obtained until we learn its maximum operating pressure. Equations (16–2) and (16–3) indicate that the frictional and normal moments are proportional to this pressure. Thus, for the left-hand shoe,
𝑀𝑁 =788𝑝𝑎1000
𝑀𝑓 =304𝑝𝑎1000
44 MS3111 Elemen MesinMAK © 2021
2.28 =
788𝑝𝑎1000 +
304𝑝𝑎1000
100 + 112
𝐹 = 2.28 𝑘𝑁
𝑝𝑎 = 443 𝑘𝑃𝑎
𝑇𝐿 =𝑓𝑝𝑎𝑏𝑟
2 cos 𝜃1 − cos 𝜃2sin 𝜃𝑎
=(0.32)(443 × 103)(0.032) (0.150)2 cos 0 − cos 126°
sin 90= 162 𝑁𝑚
The braking capacity is the total torque:
Answer (b)
𝑇 = 𝑇𝑅 + 𝑇𝐿 = 366 + 162 = 528 𝑁𝑚
𝐹 =𝑀𝑁 +𝑀𝑓
𝑐Left shoe:
45 MS3111 Elemen MesinMAK © 2021
(c) Hinge-pin reactions.Right shoe:
𝐴 = อ1
2sin2 𝜃
0°
126°
= 0.3273
𝐵 = อ𝜃
2−1
4sin 2 𝜃
0°
126°
= 1.3373
𝐷 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎=(1000 × 103)(0.032)(0.15)
sin 90°= 4.8 𝑘𝑁
𝐹𝑥 = 2.28 sin 24° = 0.93 𝑘𝑁
𝐹𝑦 = 2.28 cos 24° = 2.08 𝑘𝑁
𝑅𝑥 = 𝐷 𝐴 − 𝑓𝐵 − 𝐹𝑥 = −1.410 𝑘𝑁
𝑅𝑦 = 𝐷 𝐵 + 𝑓𝐴 − 𝐹𝑦 = 4.839 𝑘𝑁
𝑅 = 𝑅𝑥2 + 𝑅𝑦
2 = 5.04 𝑘𝑁
46 MS3111 Elemen MesinMAK © 2021
(c) Hinge-pin reactions.Left shoe:
𝐴 = อ1
2sin2 𝜃
0°
126°
= 0.3273
𝐵 = อ𝜃
2−1
4sin 2 𝜃
0°
126°
= 1.3373
𝐷 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎=(443 × 103)(0.032)(0.15)
sin 90°= 2.13 𝑘𝑁
𝐹𝑥 = 2.28 sin 24° = 0.93 𝑘𝑁
𝐹𝑦 = 2.28 cos 24° = 2.08 𝑘𝑁
𝑅𝑥 = 𝐷 𝐴 + 𝑓𝐵 − 𝐹𝑥 = 0.678 𝑘𝑁
𝑅𝑦 = 𝐷 𝐵 − 𝑓𝐴 − 𝐹𝑦 = 0.538 𝑘𝑁
𝑅 = 𝑅𝑥2 + 𝑅𝑦
2 = 0.866 𝑘𝑁
47 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.04. External Contracting Rim Clutches
and Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
48 MS3111 Elemen MesinMAK © 2021
9.3. External Contracting Rim Clutches & Brakes
The patented clutch-brake of figure has external contracting friction elements, but the actuating mechanism is pneumatic.
The mechanism can be classified as:
1. Solenoids
2. Levers, linkages, or toggle devices
3. Linkages with spring loading
4. Hydraulics and pneumatic devices
Figure 16–10An external contracting clutch-brake
49 MS3111 Elemen MesinMAK © 2021
The notation for external contracting shoes is shown in Figure 11.
The moments of friction and normal forces about the hinge pin are the same as for the internal expanding shoes.
Equations (2) and (3) apply and repeated here for convenience:
Force Analysis
Figure 16–11Notation of externalcontracting shoes.
(3)
𝑀𝑁 = න𝑑𝑁 𝑎 sin 𝜃 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃
The moment of the normal forces by 𝑀𝑁 and summing these about the hinge pin give
The moment 𝑀𝑓 of frictional forces is:
𝑀𝑓 = න𝑓𝑑𝑁 𝑟 − 𝑎 cos 𝜃 =𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎න
𝜃1
𝜃2
sin 𝜃 𝑟 − 𝑎 cos 𝜃 𝑑𝜃
(2)
50 MS3111 Elemen MesinMAK © 2021
(3)𝑀𝑁 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃
The moment of the normal forces by 𝑀𝑁 and summing these about the hinge pin give
The moment 𝑀𝑓 of frictional forces is:
𝑀𝑓 =𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎න
𝜃1
𝜃2
sin 𝜃 𝑟 − 𝑎 cos 𝜃 𝑑𝜃 (2)
Both these equations give positive values for clockwise moments (Fig. 16–11) when used for external contracting shoes. The actuating force must be large enough to balance both moments:
𝐹 =𝑀𝑁 +𝑀𝑓
𝑐(11)
51 MS3111 Elemen MesinMAK © 2021
The horizontal and vertical reactions at the hinge pin are:
(d)𝑅𝑥 = න𝑑𝑁 cos 𝜃 + න𝑓𝑑𝑁 sin 𝜃 − 𝐹𝑥 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐴 + 𝑓𝐵 − 𝐹𝑥
(e)𝑅𝑦 = න𝑓𝑑𝑁 cos 𝜃 − න𝑑𝑁 sin 𝜃 − 𝐹𝑦 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝑓𝐴 − 𝐵 − 𝐹𝑦
𝐴 = න
𝜃1
𝜃2
sin 𝜃 cos 𝜃 𝑑𝜃 = อ1
2sin2 𝜃
𝜃1
𝜃2
𝐵 = න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃 = อ𝜃
2−1
4sin 2 𝜃
𝜃1
𝜃2
where:
52 MS3111 Elemen MesinMAK © 2021
If the rotation is counterclockwise, the sign of the frictional term in each equation is reversed. Thus equation for actuating force becomes
𝐹 =𝑀𝑁 −𝑀𝑓
𝑐(13)
and self-energization exist for counterclockwise rotation.
(14b)𝑅𝑦 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎−𝑓𝐴 − 𝐵 + 𝐹𝑦
(14a)𝑅𝑥 =𝑝𝑎𝑏𝑟
sin 𝜃𝑎𝐴 − 𝑓𝐵 − 𝐹𝑥
The horizontal and vertical reaction are found to be:
•When external contracting designs are used as clutches, the effect of centrifugal force is to decrease the normal force. Thus, as the speed increases, a larger value of the actuating force 𝐹 is required.
53 MS3111 Elemen MesinMAK © 2021
dNf dN
A special case arise when the pivot is symmetrically located and also placed so that the moment of the friction forces about the pivot is zero. The geometry of such a brake will be similar to that of Fig. 12 (a).
Figure 16–12(a) Brake with symmetricalpivoted shoe; (b) wear ofbrake lining.
54 MS3111 Elemen MesinMAK © 2021
• To get a pressure-distribution relation, we assume that the lining wear is such to retain its cylindrical shape, much as a milling machine cutter feeding in the x direction would do to the shoe held in a vise, see Fig. 12 (b).
• This means the abscissa component of wear is 𝑤0 for all positions 𝜃. If wear in the radial direction is expressed as 𝑤(𝜃), then.
𝑤(𝜃) = 𝑤0 cos 𝜃
• The radial wear 𝑤(𝜃) can be expressed as
where K is a material constant, P is pressure, V is rim velocity, and t is time
𝑤(𝜃) = 𝐾𝑃𝑉𝑡
55 MS3111 Elemen MesinMAK © 2021
• Denoting 𝑃 as 𝑝(𝜃) above and solving for 𝑝(𝜃) gives
𝑝 𝜃 =𝑤(𝜃)
𝐾𝑉𝑡=𝑤0 cos 𝜃
𝐾𝑉𝑡
• Proceeding to the force analysis, we observe from Fig. 12 (a) that
• Since all elemental surface areas of the friction material see the same rubbing speed for the same duration, Τ𝑤0 (𝐾𝑉𝑡) is a constant and
where 𝑝𝑎 is the maximum value of 𝑝(𝜃).
𝑝 𝜃 = 𝑐𝑜𝑠𝑡𝑎𝑛𝑡 cos 𝜃 = 𝑝𝑎 cos 𝜃 (c)
𝑑𝑁 = 𝑝𝑏𝑟𝑑𝜃
𝑑𝑁 = 𝑝𝑎𝑏𝑟 cos 𝜃 𝑑𝜃
or (d)
(e)
56 MS3111 Elemen MesinMAK © 2021
• The distance a to the pivot is chosen by finding where the moment of the frictional forces Mf is zero.
• First, this ensures that reaction Ry is at the correct location to establish symmetrical wear.
• Second, a cosinusoidal pressure distribution is sustained, preserving our predictive ability. Symmetry means 𝜃1 = 𝜃2, so
𝑀𝑓 = 2න
0
𝜃2
𝑓𝑑𝑁 𝑎 cos 𝜃 − 𝑟 = 0
Substituting Eq. (e) gives
2𝑓𝑝𝑎𝑏𝑟න
0
𝜃2
𝑎 cos2𝜃−𝑟 cos 𝜃 𝑑𝜃 = 0
𝑎 =4𝑟 sin 𝜃2
2𝜃2 + sin 2𝜃2from which : (15)
57 MS3111 Elemen MesinMAK © 2021
• The distance a depends on the pressure distribution. Mislocatingthe pivot makes Mf zero about a different location, so the brake lining adjusts its local contact pressure, through wear, to compensate.
• With the pivot located according Eq.(15), the moment about the pin is zero.
58 MS3111 Elemen MesinMAK © 2021
• Note, too, that 𝑅𝑥 = −𝑁 and 𝑅𝑦 = −𝑓𝑁, as might be expected for the
particular choice of the dimension a.
• Therefore the torque capacity is
𝑇 = 𝑎𝑓𝑁 (18)
න𝑓𝑑𝑁 sin 𝜃 = 0
where, because of symmetry :
න𝑑𝑁 sin 𝜃 = 0
𝑅𝑦 = 2න0
𝜃2
𝑓𝑑𝑁 cos 𝜃 =𝑝𝑎𝑏𝑟𝑓
22𝜃2 + sin 2𝜃2 (17)
The horizontal and vertical reactions are
(16)𝑅𝑥 = 2න0
𝜃2
𝑑𝑁 cos 𝜃 =𝑝𝑎𝑏𝑟
22𝜃2 + sin 2𝜃2
59 MS3111 Elemen MesinMAK © 2021
The block-type hand brake shown in the figure has a face width of 1.25 in and a mean coefficient of friction of 0.25. For an estimated actuating force of 90 lbf, find the maximum pressure on the shoe and find the braking torque.
Q 16–5
Known:
𝑏 = 1.25 𝑖𝑛𝐹 = 90 𝑙𝑏𝑓𝑓 = 0.25
60 MS3111 Elemen MesinMAK © 2021
𝑎 = 62 + 82 = 10 𝑖𝑛
𝜃1
𝛼
𝜃1 = 45° − 𝛼
= 45° − tan−16
8= 8.13°
𝜃2 = 8.13° + 90° = 98.13°
𝜃𝑎 = 90°
Solution
61 MS3111 Elemen MesinMAK © 2021
dN
fdN
𝜃
r
𝑎 cos 𝜃
𝑟 − 𝑎 cos𝜃
𝑎 sin 𝜃
The moment of frictional force:
𝑀𝑓 =𝑓𝑝𝑎𝑏𝑟
sin 𝜃𝑎න
𝜃1
𝜃2
sin 𝜃 𝑟 − 𝑎 cos 𝜃 𝑑𝜃
=(0.25)𝑝𝑎(1.25)(6)
sin 90°න
8.13°
98.13°
sin 𝜃 6 − 10 cos 𝜃 𝑑𝜃
= 3.728𝑝𝑎 𝑙𝑏𝑓. 𝑖𝑛
𝑀𝑁 =𝑝𝑎𝑏𝑟𝑎
sin 𝜃𝑎න
𝜃1
𝜃2
sin2 𝜃 𝑑𝜃
The moment of normal force:
=𝑝𝑎(1.25)(6)(10)
sin 90°න
8.13°
98.13°
sin2 𝜃 𝑑𝜃 = 64.405𝑝𝑎 𝑙𝑏𝑓. 𝑖𝑛
62 MS3111 Elemen MesinMAK © 2021
𝐹𝑐 = 𝑀𝑁 −𝑀𝑓
(90)(2) = (69.405 − 3.728)𝑝𝑎
𝑝𝑎 = 27.4 𝑝𝑠𝑖 Answer
(b) Braking capacity.
𝑇𝑅 =𝑓𝑝𝑎𝑏𝑟
2 cos 𝜃1 − cos 𝜃2sin 𝜃𝑎
=(0.25)(27.4)(1.25) (6)2 cos 8.13° − cos 98.13°
sin 90°= 348.7 𝑙𝑏𝑓. 𝑖𝑛 Answer
63 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.05. Band-Type Clutches and Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
64 MS3111 Elemen MesinMAK © 2021
Application, mostly:
• Power excavators
• Hoisting machinery
• Others
9.4. Band-Type Clutches and Brakes
Broderson IC-80-1D Carry Deck
• Engine: Continental TM27, 4 cyl., 165 C.I.D., 64 hp at governed speed.
• Transmission: Borg Warner, 72T/T18, Reversing
Gearbox and Manual Shift Three Speed Gearbox.
• Brakes: Service - 4-wheel drum type brakes, Parking - Band Type Mounted on Transmission
65 MS3111 Elemen MesinMAK © 2021
(𝑃 + 𝑑𝑃) sin𝑑𝜃
2+ 𝑃 sin
𝑑𝜃
2− 𝑑𝑁 = 0
or 𝑑𝑁 = 𝑃𝑑𝜃
(a)
(b)
for small angles,
∗) sin𝑑𝜃
2=𝑑𝜃
2∗)𝑑𝑃 × 𝑑𝜃 ≈ 0
Note:Forces in vertical direction gives:
𝑃1 > 𝑃2
Why?
Figure 16–13Forces on a brake band.
66 MS3111 Elemen MesinMAK © 2021
Forces in horizontal direction gives
(𝑃 + 𝑑𝑃) cos𝑑𝜃
2− 𝑃 cos
𝑑𝜃
2− 𝑓𝑑𝑁 = 0
or𝑑𝑃 − 𝑓𝑑𝑁 = 0
(c)
(d)
Substituting the value of dN from Eq. (b) in (d) and integrating gives
න
𝑃2
𝑃1𝑑𝑃
𝑃= 𝑓න
0
𝜙
𝑑𝜃 ⇒ ln𝑃1𝑃2
= 𝑓𝜙
and𝑃1𝑃2
= 𝑒𝑓𝜙
(19)
67 MS3111 Elemen MesinMAK © 2021
𝑃𝑑𝜃 = 𝑝𝑏𝑟𝑑𝜃
The torque may be obtained from the equation
𝑇 = 𝑃1 − 𝑃2𝐷
2(20)
The normal force dN acting on element is
𝑑𝑁 = 𝑝𝑏𝑟𝑑𝜃 (e)
Substitution of dN from Eq. (b) gives
Therefore:
𝑝 =𝑃
𝑏𝑟=2𝑃
𝑏𝐷(21)
The maximum pressure will occur at the toe with the value 𝑝𝑎 =
2𝑃1𝑏𝐷
(22)
The pressure is therefore proportional to the tension in the band.
68 MS3111 Elemen MesinMAK © 2021
Q 16–11
The maximum band interface pressure on the brake shown in the figure is 620 kPa. Use a 350 mm diameter drum, a band width of 25 mm, a coefficient of friction of 0.30, and an angle-of-wrap of 270◦. Find the band tensions and the torque capacity.
Known:𝐷 = 350 𝑚𝑚𝑏 = 100 𝑚𝑚𝑝𝑎 = 620 𝑘𝑃𝑎𝑓 = 0.30𝜙 = 270°
69 MS3111 Elemen MesinMAK © 2021
Solution
The band tensions
𝑝𝑎 =2𝑃1𝑏𝐷
Eq. (22)
𝑃1𝑃2
= 𝑒𝑓𝜙Eq. (19)
𝑃1 =𝑝𝑎𝑏𝐷
2=(620)(0.1)(0.35)
2= 10.85 𝑘𝑁 Answer
𝑃2 =𝑃1𝑒𝑓𝜙
=10.85
𝑒(0.3)(270°×𝜋
180°)= 2.64 𝑘𝑁 Answer
The torque capacity.
𝑇 = 𝑃1 − 𝑃2𝐷
2Eq. (20) = 10.85 − 2.64
0.350
2= 1.437 𝑘𝑁𝑚 Answer
70 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.06. Frictional-Contact Axial Clutches
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
71 MS3111 Elemen MesinMAK © 2021
• Mating frictional members are moved in a direction parallel to shaft.
• Most application: automotive
9.5. Frictional-Contact Axial Clutches
72 MS3111 Elemen MesinMAK © 2021
Figure 16–15An oil-actuated multiple-disk clutch-brake for operation in an oil bath or spray
Figure 16–14Cross-sectional view of a single-plate clutch; A, driver; B, driven plate (keyed to driven shaft); C, actuator
73 MS3111 Elemen MesinMAK © 2021
Advantages of the disk clutch:
Free from centrifugal effects
Large frictional area which can be installed in small space
More effective heat-dissipation surfaces
Favorable pressure distribution
Two methods for the analysis:
➢ Uniform wear
➢ Uniform pressure
74 MS3111 Elemen MesinMAK © 2021
𝑝𝑟 = 𝑝𝑎𝑑
2or 𝑝 = 𝑝𝑎
𝑑
2𝑟
Uniform wear
After initial wear has taken place and the disks have worn down to the point where uniform wear becomes possible, the greatest pressure must occur at 𝑟 = Τ𝐷 2 in order for wear to be uniform. Denoting the maximum pressure by 𝑝𝑎 , we can then write.(see the explanation in Shigley, page 847)
Figure 16–16Disk friction member.(a)
75 MS3111 Elemen MesinMAK © 2021
Figure 16–16Disk friction member.
Referring to Fig. 16, we have an element of area of radius 𝑟 and thickness 𝑑𝑟 . The area of this element is 2𝜋𝑟𝑑𝑟 , so that the normal force acting upon this element is 𝑑𝐹 = 2𝜋𝑝𝑟𝑑𝑟. Thus, the total normal force become:
𝐹 = න
Τ𝑑 2
𝐷/2
2𝜋𝑝𝑟𝑑𝑟 = 𝜋𝑝𝑎𝑑 න
Τ𝑑 2
𝐷/2
𝑑𝑟 =𝜋𝑝𝑎𝑑
2𝐷 − 𝑑 (23)
The torque is found by integrating the product of the frictional force and the radius:
𝑇 = න
Τ𝑑 2
𝐷/2
2𝜋𝑓𝑝𝑟2𝑑𝑟 = 𝜋𝑓𝑝𝑎𝑑 න
Τ𝑑 2
𝐷/2
𝑟𝑑𝑟 =𝜋𝑓𝑝𝑎𝑑
8𝐷2 − 𝑑2
𝑇 =𝐹𝑓
4𝐷 + 𝑑
(24)
(25)
76 MS3111 Elemen MesinMAK © 2021
Uniform Pressure
When uniform pressure can be assumed over the area of the disk, the actuating force 𝐹 is simply the product of the pressure and the area
𝐹 =𝜋𝑝𝑎4
𝐷2 − 𝑑2 (26)
Note:Equations (26) and (28) are for single pair of mating surface.This value must be multiplied by the number of pairs of surfaces in contact.
As before, the torque is found by integrating the product of the frictional force and the radius:
𝑇 = 2𝜋𝑓𝑝𝑎 න
Τ𝑑 2
𝐷/2
𝑟2𝑑𝑟 =𝜋𝑓𝑝𝑎24
𝐷3 − 𝑑3
𝑇 =𝐹𝑓
3
𝐷3 − 𝑑3
𝐷2 − 𝑑2(28)
(27)
77 MS3111 Elemen MesinMAK © 2021
Figure 16–17Dimensionless plot of Eqs. (b) and (c).
Difference characteristic of uniform pressure and uniform wear
𝑈𝑛𝑖𝑓𝑜𝑟𝑚𝑊𝑒𝑎𝑟 (𝑜𝑙𝑑 𝑐𝑙𝑢𝑡𝑐ℎ):𝑇
𝑓𝐹𝐷=1
41 +
𝑑
𝐷
𝑈𝑛𝑖𝑓𝑜𝑟𝑚 𝑃𝑟𝑒𝑠𝑠𝑢𝑟𝑒 (𝑛𝑒𝑤 𝑐𝑙𝑢𝑡𝑐ℎ):
𝑇
𝑓𝐹𝐷=1
3
1 −𝑑𝐷
3
1 −𝑑𝐷
2
(b)
(c)
78 MS3111 Elemen MesinMAK © 2021
Q 16–16
A plate clutch has a single pair of mating friction surfaces 250-mm OD by 175-mm ID. The mean value of the coefficient of friction is 0.30, and the actuating force is 4 kN.a) Find the maximum pressure and the torque capacity using the
uniform-wear model.b) Find the maximum pressure and the torque capacity using the
uniform-pressure model.
Known:
𝑂𝐷 = 250 𝑚𝑚𝐼𝐷 = 175 𝑚𝑚𝑓 = 0.3𝐹 = 4 𝑘𝑁
79 MS3111 Elemen MesinMAK © 2021
Solution
a) Find the maximum pressure and the torque capacity using the uniform-wear model.
𝐹 =𝜋𝑝𝑎𝑑
2𝐷 − 𝑑Eq. (23)
𝑇 =𝐹𝑓
4𝐷 + 𝑑
Eq. (25)
𝑝𝑎 =2𝐹
𝜋𝑑 𝐷 − 𝑑=
2(4000)
𝜋(0.175) 0.250 − 0.175= 194 𝑘𝑃𝑎 Answer
=(4000)(0.3)
40.250 + 0.175 = 127.5 𝑁𝑚 Answer
80 MS3111 Elemen MesinMAK © 2021
b) Find the maximum pressure and the torque capacity using the uniform-pressure model.
𝐹 =𝜋𝑝𝑎4
𝐷2 − 𝑑2
Eq. (26)
𝑇 =𝐹𝑓
3
𝐷3 − 𝑑3
𝐷2 − 𝑑2
Eq. (28)
𝑝𝑎 =4𝐹
𝜋 𝐷2 − 𝑑2=
4(4000)
𝜋 0.2502 − 0.1752= 159 𝑘𝑃𝑎 Answer
=(4000)(0.3)
3
0.2503 − 0.1753
0.2502 − 0.1752= 128 𝑁𝑚 Answer
81 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.07. Disk Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
82 MS3111 Elemen MesinMAK © 2021
• There is no fundamental difference
between a disk clutch and a disk
brake.
• The analysis of preceding section
applies to disk brakes too.
• Disk brake has no self-energization,
and hence is not so susceptible to
changes in the coefficient of friction.
9.6. Disk Brakes
83 MS3111 Elemen MesinMAK © 2021
• Fig. 18 shows a floating caliper disk brake.
• The caliper support a single floating piston
actuated by hydraulic pressure.
• The action is like a screw clamp, with the
piston replacing the function of the screw.
• The floating action compensates for wear
and ensures a fairly constant pressure over
the area of the friction pads.
Figure 16–18An automotive disk brake.
84 MS3111 Elemen MesinMAK © 2021
Figure 16–19Geometry of contact area of an annular-pad segment of a caliper brake.
Fig. 19 is the geometry of an annular-pad brake contact area. The governing axial wear equation is (see Eq. 12-27, p. 663 -Shigley)
𝑤 = 𝑓1𝑓2𝐾𝑃𝑉𝑡
Of interest also is the effective radius 𝑟𝑒 , which is the radius of an equivalent
shoe of infinitesimal radial thickness.
Annular-pad brake contact area.
The coordinate ҧ𝑟 locates the line of action of force F that intersects the y axis.
85 MS3111 Elemen MesinMAK © 2021
If 𝑝 is the local contact pressure, the actuating force 𝐹 is
𝐹 = න𝜃1
𝜃2
න𝑟𝑖
𝑟𝑜
𝑝𝑟𝑑𝑟𝑑𝜃 = 𝜃2 − 𝜃1 න𝑟𝑖
𝑟𝑜
𝑝𝑟𝑑𝑟
(29)
Figure 16–19Geometry of contact area of an annular-pad segment of a caliper brake.
and the friction torque 𝑇 is
𝑇 = න𝜃1
𝜃2
න𝑟𝑖
𝑟𝑜
𝑓𝑝𝑟2𝑑𝑟𝑑𝜃 = 𝜃2 − 𝜃1 𝑓න𝑟𝑖
𝑟𝑜
𝑝𝑟2𝑑𝑟
(30)
The equivalent radius 𝑟𝑒 can be found from 𝑓𝐹𝑟𝑒 = 𝑇, or
𝑟𝑒 =𝑇
𝑓𝐹=𝑟𝑖𝑟𝑜 𝑝𝑟2𝑑𝑟
𝑟𝑖𝑟𝑜 𝑝𝑟𝑑𝑟
(31)
86 MS3111 Elemen MesinMAK © 2021
The locating coordinate ҧ𝑟 of the activating force is found by taking moments about the x axis:
𝑀𝑥 = 𝐹 ҧ𝑟 = න𝜃1
𝜃2
න𝑟𝑖
𝑟𝑜
𝑝𝑟 𝑟 sin 𝜃 𝑑𝑟𝑑𝜃 = cos 𝜃1 − cos 𝜃2 න𝑟𝑖
𝑟𝑜
𝑝𝑟2𝑑𝑟
ҧ𝑟 =𝑀𝑥
𝐹=
cos 𝜃1 − cos 𝜃2𝜃2 − 𝜃1
𝑟𝑒 (32)
87 MS3111 Elemen MesinMAK © 2021
Uniform Wear
Using that pressure distribution 𝑝 = Τ𝑝𝑎𝑟𝑖 𝑟. Eqs. (29) to (32) become
𝐹 = 𝜃2 − 𝜃1 න𝑟𝑖
𝑟𝑜 𝑝𝑎𝑟𝑖𝑟
𝑟𝑑𝑟 = 𝜃2 − 𝜃1 𝑝𝑎𝑟𝑖 𝑟𝑜 − 𝑟𝑖 (33)
𝑇 = 𝜃2 − 𝜃1 𝑓න𝑟𝑖
𝑟𝑜 𝑝𝑎𝑟𝑖𝑟
𝑟2𝑑𝑟 =1
2𝜃2 − 𝜃1 𝑓𝑝𝑎𝑟𝑖 𝑟𝑜
2 − 𝑟𝑖2 (34)
𝑟𝑒 =𝑇
𝑓𝐹=𝑟𝑖𝑟𝑜 𝑝𝑎𝑟𝑖
𝑟𝑟2𝑑𝑟
𝑟𝑖𝑟𝑜 𝑝𝑎𝑟𝑖
𝑟𝑟𝑑𝑟
=𝑟𝑜 + 𝑟𝑖2
(35)
ҧ𝑟 =𝑀𝑥
𝐹=
cos 𝜃1 − cos 𝜃2𝜃2 − 𝜃1
𝑟𝑒 =cos 𝜃1 − cos 𝜃2
𝜃2 − 𝜃1
𝑟𝑜 + 𝑟𝑖2
(36)
88 MS3111 Elemen MesinMAK © 2021
Uniform Pressure
In this situation, approximated by a new brake, 𝑝 = 𝑝𝑎 , Eqs. (29) to (32) become
𝐹 = 𝜃2 − 𝜃1 න𝑟𝑖
𝑟𝑜
𝑝𝑎𝑟𝑑𝑟 =1
2𝜃2 − 𝜃1 𝑝𝑎 𝑟𝑜
2 − 𝑟𝑖2 (37)
𝑇 = 𝜃2 − 𝜃1 𝑓න𝑟𝑖
𝑟𝑜
𝑝𝑎𝑟2𝑑𝑟 =
1
3𝜃2 − 𝜃1 𝑓𝑝𝑎 𝑟𝑜
3 − 𝑟𝑖3 (38)
𝑟𝑒 =𝑇
𝑓𝐹=𝑟𝑖𝑟𝑜 𝑝𝑎𝑟
2𝑑𝑟
𝑟𝑖𝑟𝑜 𝑝𝑎𝑟𝑑𝑟
=2
3
𝑟𝑜3 − 𝑟𝑖
3
𝑟𝑜2 − 𝑟𝑖
2(39)
ҧ𝑟 =𝑀𝑥
𝐹=
cos 𝜃1 − cos 𝜃2𝜃2 − 𝜃1
𝑟𝑒 =cos 𝜃1 − cos 𝜃2
𝜃2 − 𝜃1
2
3
𝑟𝑜3 − 𝑟𝑖
3
𝑟𝑜2 − 𝑟𝑖
2(40)
89 MS3111 Elemen MesinMAK © 2021
EXAMPLE 16–3
Two annular pads, 𝑟𝑖 = 3.875 in, 𝑟𝑜 = 5.50 in, subtend an angle of 108°, have a coefficient of friction of 0.37, and are actuated by a pair of hydraulic cylinders 1.5 in in diameter. The torque requirement is 13000 lbf · in. For uniform weara) Find the largest normal pressure 𝑝𝑎 .b) Estimate the actuating force 𝐹.c) Find the equivalent radius 𝑟𝑒 and force location ҧ𝑟.d) Estimate the required hydraulic pressure.
Known 𝑟𝑖 = 3.875 𝑖𝑛𝑟𝑜 = 5.500 𝑖𝑛𝑓 = 0.37𝜃1 = 36°𝜃2 = 144°
90 MS3111 Elemen MesinMAK © 2021
Solution Two annular pads, total torque = 13000 lbf.in.For each pad, 𝑇 = Τ13000 2 = 6500 𝑙𝑏𝑓. 𝑖𝑛
𝑇 =1
2𝜃2 − 𝜃1 𝑓𝑝𝑎𝑟𝑖 𝑟𝑜
2 − 𝑟𝑖2Eq. (34)
a) Find the largest normal pressure 𝑝𝑎 for uniform wear.
𝑝𝑎 =2𝑇
𝜃2 − 𝜃1 𝑓𝑟𝑖 𝑟𝑜2 − 𝑟𝑖
2
=2(6500)
(144° − 36°) ×𝜋180
(0.37)(3.875)(5.52 − 3.8752)= 315.8 𝑝𝑠𝑖
Answer
b) Estimate the actuating force 𝐹 for uniform wear.
𝐹 = 𝜃2 − 𝜃1 𝑝𝑎𝑟𝑖 𝑟𝑜 − 𝑟𝑖Eq. (33)
= 144° − 36°𝜋
180315.8 3.875 5.500 − 3.875 = 3748 𝑙𝑏𝑓
Answer
91 MS3111 Elemen MesinMAK © 2021
c) Find the equivalent radius 𝑟𝑒 and force location ҧ𝑟 for uniform wear.
𝑟𝑒 =𝑟𝑜 + 𝑟𝑖2
=5.500 + 3.875
2= 4.688 𝑖𝑛Eq. (35)
ҧ𝑟 =cos 𝜃1 − cos 𝜃2
𝜃2 − 𝜃1𝑟𝑒 =
cos 36° − cos 144°
144° − 36° ×𝜋180
4.688 = 4.024 𝑖𝑛Eq. (36)
Answer
d) Estimate the required hydraulic pressure.
Each cylinder supplies the actuating force, 3748 lbf
𝑝ℎ𝑦𝑑𝑟𝑎𝑢𝑙𝑖𝑐 =𝐹
𝐴𝑝=
3748𝜋4(1.5)2
= 2121 𝑝𝑠𝑖 Answer
92 MS3111 Elemen MesinMAK © 2021
Circular (Button) Pad Caliper Brake
Figure 20 displays the circular pad geometry. Numerical integration is necessary to analyze this brake since the boundaries are difficult to handle in closed form. Table 1 gives the parameters for this brake as determined by Fazekas.
Table 1 Parameters for a Circular-Pad Caliper Brake
Figure 16–20Geometry of circular pad of acaliper brake.
Effective radius, 𝑟𝑒 = 𝛿𝑒
93 MS3111 Elemen MesinMAK © 2021
Figure 16–20Geometry of circular pad of acaliper brake.
Effective radius, 𝑟𝑒 = 𝛿𝑒
The effective radius is given by
𝑟𝑒 = 𝛿𝑒 (41)
The actuating force is given by
𝐹 = 𝜋𝑅2𝑝𝑎𝑣 (42)
and the torque is given by𝑇 = 𝑓𝐹𝑟𝑒 (43)
94 MS3111 Elemen MesinMAK © 2021
EXAMPLE 16–4
A button-pad disk brake uses dry sintered metal pads. The pad radius is ½ in, and its center is 2 in from the axis of rotation of the 312 -in-diameter disk. Using half of the largest allowable pressure, pmax = 350 psi, find the actuating force and the brake torque. The coefficient of friction is 0.31.
Known
𝑅 = 0.5 𝑖𝑛𝑒 = 2 𝑖𝑛𝑝𝑚𝑎𝑥 = 350 𝑝𝑠𝑖𝑓 = 0.31
95 MS3111 Elemen MesinMAK © 2021
𝑅
𝑒=0.5
2= 0.25
By interpolation:
𝛿 = 0.963𝑝𝑚𝑎𝑥
𝑝𝑎𝑣= 1.290
𝑟𝑒 = 𝛿𝑒 = 0.963 2 = 1.926 𝑖𝑛Eq. (41)
𝑝𝑎𝑣 =𝑝𝑚𝑎𝑥
1.290=
350
1.290= 135.7 𝑝𝑠𝑖
𝐹 = 𝜋𝑅2𝑝𝑎𝑣 = 𝜋 0.5 2 135.7= 106.6 𝑙𝑏𝑓
Eq. (42)
Answer
𝑇 = 𝑓𝐹𝑟𝑒 = 0.31 106.6 1.926 = 63.65 𝑙𝑏𝑓. 𝑖𝑛Eq. (43) Answer
Solution
96 MS3111 Elemen MesinMAK © 2021
Teknik Mesin - FTMD ITB
09.08. Cone Clutches and Brakes
MS3111 - Elemen Mesin
Modul 09Clutches, Brakes, Couplings
and Flywheel Part I
97 MS3111 Elemen MesinMAK © 2021
• Consist of a cup and a cone.
• Cone angle, the diameter and face width of the cone are the important geometric design parameters.
• If the cone angle is too small, say, less than about 8o, then the force required to disengage the clutch may be quite large.
• Wedging effect lessens rapidly when larger cone angles are used.
• A good compromise can usually be found between 10o – 15o.
8.7. Cone Clutch and Brakes
98 MS3111 Elemen MesinMAK © 2021
Actuating force and torque transmittedcan be found using Fig. 22.
Uniform Wear
The pressure relation is the same as for the axial clutch
𝑝 = 𝑝𝑎𝑑
2𝑟(a)
The element area 𝑑𝐴 of radius 𝑟 and width Τ𝑑𝑟 sin𝛼 is
𝑑𝐴 = Τ(2𝜋𝑟𝑑𝑟) sin 𝛼 (b)
Figure 16–22Contact area of a cone clutch.
99 MS3111 Elemen MesinMAK © 2021
Figure 16–22Contact area of a cone clutch.
As shown in Fig. 22, the operating force will be the integral of the axial component of the differential force 𝑝𝑑𝐴. Thus
𝐹 = න𝑝𝑑𝐴 sin 𝛼 = න
Τ𝑑 2
Τ𝐷 2
𝑝𝑎𝑑
2𝑟
2𝜋𝑟 𝑑𝑟
sin 𝛼(sin 𝛼)
𝐹 = 𝜋𝑝𝑎𝑑 න
Τ𝑑 2
Τ𝐷 2
𝑑𝑟 =𝜋𝑝𝑎𝑑
2𝐷 − 𝑑 (44)
which is the same result as in Eq. (23)
100 MS3111 Elemen MesinMAK © 2021
The differential friction force is 𝑓𝑝𝑑𝐴, and the torque is the integral of the product of this force with the radius. Thus:
𝑇 = න𝑟𝑓𝑝𝑑𝐴 = න
Τ𝑑 2
Τ𝐷 2
(𝑟𝑓) 𝑝𝑎𝑑
2𝑟
2𝜋𝑟𝑑𝑟
sin 𝛼=𝜋𝑓𝑝𝑎sin 𝛼
න
Τ𝑑 2
Τ𝐷 2
𝑟𝑑𝑟 =𝜋𝑓𝑝𝑎𝑑
8 sin 𝛼𝐷2 − 𝑑2 (45)
Note that Eq. (24) is a special case of Eq. (45), with = 90o.
Using Eq. (44), the torque can also be written
𝑇 =𝐹𝑓
4 sin 𝛼𝐷 + 𝑑 (46) Note that Eq. (25) is also a special case of Eq.
(46), with = 90o.
101 MS3111 Elemen MesinMAK © 2021
Uniform Pressure
Using 𝑝 = 𝑝𝑎, the actuating force and torque are found to be
𝐹 = න𝑝𝑎𝑑𝐴 sin𝛼 = න
Τ𝑑 2
Τ𝐷 2
𝑝𝑎2𝜋𝑟𝑑𝑟
sin𝛼sin𝛼 =
𝜋𝑝𝑎4
𝐷2 − 𝑑2 (47)
𝑇 = න𝑟𝑓𝑝𝑎𝑑𝐴 = න
Τ𝑑 2
Τ𝐷 2
𝑟𝑓𝑝𝑎2𝜋𝑟𝑑𝑟
sin𝛼=
𝜋𝑓𝑝𝑎12 sin𝛼
𝐷3 − 𝑑3 (48)
(49)𝑇 =𝐹𝑓
3 sin𝛼
𝐷3 − 𝑑3
𝐷2 − 𝑑2
102 MS3111 Elemen MesinMAK © 2021
As in the case of the axial clutch, we can write Eq. (43) dimensionlessly as
and write Eq. (49) as
This time there are six (T, α, f, F, D, and d) parameters and four pi () terms:
As in Fig. 17, we plot T sin α/( f FD) as ordinate and d/D as abscissa. The plots and conclusions are the same ➔ Students are recommended to do the plot.
𝑇 sin 𝛼
𝑓𝐹𝐷=1 +
𝑑𝐷
4
𝑇 sin 𝛼
𝑓𝐹𝐷=1
3
1 −𝑑𝐷
3
1 −𝑑𝐷
2
𝜋1 =𝑇
𝐹𝐷𝜋2 = 𝑓 𝜋3 = sin 𝛼 𝜋4 =
𝑑
𝐷
103 MS3111 Elemen MesinMAK © 2021
A cone clutch has D = 12 in, d = 11 in, a cone length of 2.25 in, and a coefficient of friction of 0.28. A torque of 1800 lbf.in is to be transmitted. For this requirement, estimate the actuating force and pressure by both models.
Q 16–19
Known
𝐷 = 12 𝑖𝑛𝑑 = 11 𝑖𝑛𝐿 = 2.25 𝑖𝑛𝑓 = 0.28𝑇 = 1800 𝑙𝑏𝑓. 𝑖𝑛
CLNot to scale
5.5
6.02.25
𝛼𝛼 = tan−1
0.5
2.25= 12.53°
104 MS3111 Elemen MesinMAK © 2021
Solution
𝑇 =𝜋𝑓𝑝𝑎𝑑
8 sin 𝛼𝐷2 − 𝑑2Eq. (45)
Uniform Wear
(1800) =𝜋(0.28)𝑝𝑎(11)
8 sin 12.53°122 − 112
𝐹 =𝜋𝑝𝑎𝑑
2𝐷 − 𝑑 =
𝜋(14.04)(11)
212 − 1 = 243 𝑙𝑏𝑓Eq. (44) Answer
𝑝𝑎 = 14.04 𝑝𝑠𝑖 Answer
105 MS3111 Elemen MesinMAK © 2021
Uniform Pressure
𝑇 =𝜋𝑓𝑝𝑎12 sin 𝛼
𝐷3 − 𝑑3Eq. (48)
1800 =𝜋(0.28)𝑝𝑎12 sin 12.53°
123 − 113 𝑝𝑎 = 13.42 𝑝𝑠𝑖 Answer
𝐹 =𝜋𝑝𝑎4
𝐷2 − 𝑑2 =𝜋(13.42)
4122 − 112 = 242 𝑙𝑏𝑓Eq. (47) Answer
106 MS3111 Elemen MesinMAK © 2021
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Thank YouLecturers
Faculty of Mechanical and Aerospace Engineering
Institut Teknologi Bandung
Modul 09 Clutches, Brakes, Couplings and Flywheel Part I
top related