motorbike parting

Motorbike Parting Tutorial

i

Table of Contents Motorbike Parting Introduction......................................................................................................... 1

Analyze ............................................................................................................................................ 2

Parting Setup ............................................................................................................................... 2

Split .............................................................................................................................................. 5

Parting Faces................................................................................................................................. 10

Internal........................................................................................................................................... 10

Cylindrical................................................................................................................................... 10

Parting Curve ............................................................................................................................. 14

External.......................................................................................................................................... 16

Sweep ........................................................................................................................................ 16

Extend ........................................................................................................................................ 21

Inner area................................................................................................................................... 25

Side area.................................................................................................................................... 29

Mirror.......................................................................................................................................... 36

Bounded..................................................................................................................................... 38

Final ........................................................................................................................................... 41

Attach ......................................................................................................................................... 45

Export ............................................................................................................................................ 49

Stock .......................................................................................................................................... 49

Sets ............................................................................................................................................ 51

Motorbike Parting

Cimatron E6 Tutorials 1

Motorbike Parting Introduction

In this exercise, the parting surfaces of the motorbike part will be created and the core, cavity and sliders will be exported.

Motorbike Parting

2 Cimatron E6 Tutorials

Analyze

Parting Setup

Invoke the Parting Setup wizard, select the Master Motorcycle.elt part document (located in the \\Tutorial Work Files\Data To Steel directory).

Set the following options:

Click the Preferences Editor icon and view the Part/Color/Quick_Split preferences.

Motorbike Parting

Cimatron E6 Tutorials 3

The color of Quick Split sets can now be defined.

Within the Preferences Editor, select Part/General/Quick Split Quality and verify that 'Recommended' is selected.

Motorbike Parting

4 Cimatron E6 Tutorials

Click OK in the Preferences Editor and in the Parting Setup Wizard.

Motorbike Parting

Cimatron E6 Tutorials 5

Split

Select the Quick Split function.

Change the arrows direction to Along Y, add vertical faces to bottom and click OK.

Motorbike Parting

6 Cimatron E6 Tutorials

The following steps are redundant when using the 'High Quality' option in the Quick Split Quality preferences. However, in this exercise the steps below are introduced to illustrate how to deal with a normal, which is pointing in the wrong direction.

Click the Object Direction icon.

Notice the black faces on EACH side.

Toggle the Auto option to Manual.

The Manual option lets you manually pick each object and flip its normal. It is useful in cases where the body includes several lumps as it allows each lump to be flipped individually.

Pick the five black faces to invert their normals i.e. they appear white, and click OK.

Motorbike Parting

Cimatron E6 Tutorials 7

Check for Draft Angles.

Motorbike Parting

8 Cimatron E6 Tutorials

Notice that the same faces are shown in red as undercuts.

These faces were assigned to the RED set since their face normals were inverted.

Attach the marked faces to the BLUE set.

Pick the required faces and Middle Mouse Click on a blue face.

The Draft Angle analysis now shows no undercuts.

Motorbike Parting

Cimatron E6 Tutorials 9

Motorbike Parting

10 Cimatron E6 Tutorials

Parting Faces

Internal

Cylindrical

The two sliders will now be split.

In the Quick Split function, pick the New Direction tab and toggle the One Direction option to Both Directions.

Pick the arrow base and select the option Cylindrical/Conic Center.

Motorbike Parting

Cimatron E6 Tutorials 11

Pick one of the sliders cylindrical faces.

Click OK in the New Directions Feature Guide.

Attach the rest of the sliders faces to achieve the result shown below:

Motorbike Parting

12 Cimatron E6 Tutorials

Motorbike Parting

Cimatron E6 Tutorials 13

Motorbike Parting

14 Cimatron E6 Tutorials

Parting Curve

Create the internal parting curves.

Select Parting Curve/Internal Part. Curve.

Use the default Adjoin Tolerance value of 0.1 and click OK in the Feature Guide.

Select Parting Surf/Internal.

Motorbike Parting

Cimatron E6 Tutorials 15

Click OK in the Feature Guide.

All the internal islands are now closed.

Motorbike Parting

16 Cimatron E6 Tutorials

External

Sweep

The external parting faces will now be created.

Select Parting Lines/Composite Curve.

Hide the following sets and Parting Surfaces:

When creating a composite curve on a split part, selection of the curves is made easier by displaying the relevant faces only.

Create the following composite curve:

Motorbike Parting

Cimatron E6 Tutorials 17

Select the Sweep Face icon from the Parting Guide, under Parting Surf.

Pick the composite curve created, and change the direction to Along X (pointing outwards).

Motorbike Parting

18 Cimatron E6 Tutorials

Show the Split-03 set.

Create the composite curve shown here and sweep a face in the -Z direction.

Open the sketcher. As the sketch plane pick the face indicated below:

Motorbike Parting

Cimatron E6 Tutorials 19

Rotate to plane and draw a line slanted at 1.5 degrees from the vertical direction.

Sweep this line in the X direction to Both Sides.

Motorbike Parting

20 Cimatron E6 Tutorials

Motorbike Parting

Cimatron E6 Tutorials 21

Extend

Select Solid/Merge.

Pick the two faces highlighted below:

Notice the arrow directions.

Click OK.

The slider will now be closed.

Select the Blend Face icon and create the Blend face below:

Motorbike Parting

22 Cimatron E6 Tutorials

Pick the boundary shown here.

Extend the face as shown below:

Motorbike Parting

Cimatron E6 Tutorials 23

The following step is to stitch the faces, in order to create a round. This means that the open edges will be "lost". Therefore, before the stitch operation, the face shown here will be extended, using its smooth open edge.

Select the Extend Face icon.

Pick the edge highlighted and create a Tangent Continuous extension.

Select Faces/Stitch and stitch the faces into a single object.

Motorbike Parting

24 Cimatron E6 Tutorials

Create the following round:

Motorbike Parting

Cimatron E6 Tutorials 25

Inner area

Close the inner area below, by a Bounded Face.

Click here to see the curve selected.

Motorbike Parting

26 Cimatron E6 Tutorials

Create the Blend Face by picking the two edges as shown:

Motorbike Parting

Cimatron E6 Tutorials 27

Close the area by an additional Blend Face (with boundaries).

Motorbike Parting

28 Cimatron E6 Tutorials

Create a composite curve and extend the edges shown below, using the Tangent Continuous option.

Motorbike Parting

Cimatron E6 Tutorials 29

Side area

Extend the edge shown here using the Natural Continuous option.

Create the composite curve.

Motorbike Parting

30 Cimatron E6 Tutorials

Click the Drive Face icon and create a Drive Face.

Motorbike Parting

Cimatron E6 Tutorials 31

Below the drive face, create the following extend face:

Create the composite curve shown below:

Motorbike Parting

32 Cimatron E6 Tutorials

Create a Natural - Multi Continuous Extension, using the Manual Directions option.

The Auto Directions parameter displays all arrows on the vertices and their corresponding default directions are calculated. The direction of the arrows can be set by right-clicking on the arrow. .One or more arrows can be removed so that their default direction at this point will not be calculated.

Motorbike Parting

Cimatron E6 Tutorials 33

The Manual Directions parameter displays only two arrows at the end vertices of each face. Side directions of extensions on each vertex can be added.

Create the Composite Curve shown here.

Select Faces/Modify/Boundary.

Pick the face as shown below, using the Keep Original option.

Pick the edge indicated and create a Natural Continuous extend face using the Same Face option.

Motorbike Parting

34 Cimatron E6 Tutorials

Trim the extended face using the composite curve.

Flip the trimming side so that the result will be the parting face shown here.

Motorbike Parting

Cimatron E6 Tutorials 35

Motorbike Parting

36 Cimatron E6 Tutorials

Mirror

Create Main Planes.

As the part is symmetric we can now mirror the parting faces to the other side.

Select Edit/Copy Geometry/Mirror and pick the Parting faces.

Motorbike Parting

Cimatron E6 Tutorials 37

Pick the YZ main plane as the symmetry plane.

Click OK in the Feature Guide.

Motorbike Parting

38 Cimatron E6 Tutorials

Bounded

Select Faces/Bounded, click the Composite Curve icon and pick the curves as shown.

Press OK to confirm the composite curve and then again to create the bounded face.

Create the plane shown below:

Select Datum/Plane/Parallel and pick the ZX plane.

Motorbike Parting

Cimatron E6 Tutorials 39

Trim the Parting Faces, using the plane created.

Motorbike Parting

40 Cimatron E6 Tutorials

Flip the Trimming Side and click OK in the Feature Guide.

Motorbike Parting

Cimatron E6 Tutorials 41

Final

Open the sketcher on the XY plane, and draw the following sketch:

Sweep this curve by a delta of 500.

The newly created face will now be cut with the intersecting faces. The Faces/Trim function is normally used in this procedure, however here the Merge function will be used as it enables the procedures completion in a single operation.

Motorbike Parting

42 Cimatron E6 Tutorials

Stitch the following faces:

Merge the two objects.

Notice the arrow directions.

Motorbike Parting

Cimatron E6 Tutorials 43

Create a sketch on the parallel plane created in the last step.

Use the parting faces end points as references.

Motorbike Parting

44 Cimatron E6 Tutorials

Create composite curves (using a tolerance of 0.1 for the first face) and use them to create the three bounded faces below:

Motorbike Parting

Cimatron E6 Tutorials 45

Attach

Show all the sets.

The parting faces will now be attached to their relevant sets.

Click the Attach Attribute icon in the Parting Guide.

Pick the faces to assign and exit via the middle mouse button .

Motorbike Parting

46 Cimatron E6 Tutorials

Pick the two sets (Split-01 and Slpit-02) to which the faces belong.

Click Apply in the Feature Guide.

Pick the faces to assign and the sets they belong to.

Motorbike Parting

Cimatron E6 Tutorials 47

Repeat the above step on the other side of the part for Split-01and Split-04.

Pick the faces to assign and the sets they belong to.

Motorbike Parting

48 Cimatron E6 Tutorials

Repeat the above step on the other side of the part for Split-02and Split-04.

Below is the list of sets created and their corresponding colors:

Motorbike Parting

Cimatron E6 Tutorials 49

Export

Stock

Select the New Stock icon.

Open the sketcher .

On the parallel plane, draw the following Sketch:

Motorbike Parting

50 Cimatron E6 Tutorials

Exit the sketcher and enter the parameters as shown below:

Click OK in the Feature Guide.

Motorbike Parting

Cimatron E6 Tutorials 51

Sets

The Work CS will now be defined.

The Z of the Work CS determines the orientation in which the active parts will be positioned in the mold. If no Work CS is defined, the system uses the Active UCS.

Select the Work CS icon from the Parting Guide.

Select either the Cavity, Core or slider parts from the Parting Tree, to view the direction of the selected set.

Select Along Y as the Work CS direction.

Motorbike Parting

52 Cimatron E6 Tutorials

Click OK in the Feature Guide.

Right Click on the sets in the Parting Tree and rename them as follows:

Motorbike Parting

Cimatron E6 Tutorials 53

Select the Export Mold icon.

The export operation creates a UCS for each exported set, according to its parting direction. These UCS are not visible in the Work part. The UCS is positioned either on the Model UCS (default) or on the Active UCS position.

Load the Master Motorcycle-Work-Cavity part.

From the Active Tools menu, click the Parting Stitch icon.

Motorbike Parting

54 Cimatron E6 Tutorials

The Parting Faces have been stitched into one object.

Click the Cut icon and cut the stock with the parting faces.

Hide the parting faces.

Motorbike Parting

Cimatron E6 Tutorials 55

Notice the direction of the active UCS (in red).

Repeat the above operation for the core and the two sliders.

Motorbike Parting

56 Cimatron E6 Tutorials