mrk-ms&m2s qig copy · 2017. 5. 10. · model: ugt-mst110, ugt-mst210, ugt-m2st120, ugt-m2s220 m.2...
Post on 30-Jan-2021
6 Views
Preview:
TRANSCRIPT
-
Installation Guide
Information in this document is subject to change without notice.Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in ChinaPrinted on Recycled Paper. Copyright © 2016 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
Model: UGT-MST110, UGT-MST210, UGT-M2ST120, UGT-M2S220
www.vantecusa.com
M.2 card comes in different length and sizes (42, 60, 80mm), match your M.2 card length to the hole alignment to decide which mounting hole to use.
2.
22x80 mm
M.2 Card
22x60 mm
22x42 mm
80 mm
60 mm
42 mm
M.2 Installation Steps
Verify the package contents.1.
Screws and washer for mounting M.2 card to PCB
Screws for mounting PCB to Plastic Mounting Board
Screws for mounting PCB to Plastic Mounting Board to 3.5” or 5.25” or custom mounting
Mounted Standard L bracket
PlasticMounting
Board
PCB
The device is ready to be integrated into your system.3.2.
12
Attached M.2 Card by inserting the M.2 Card and secure using the washer and screw to hold the M.2 card in place.
mSATA card comes in different sizes (27, 50, or 70mm), match your mSATA card size to the hole alignment to decide which mounting hole or clip to use.
2.
70 mm
mSATA card
50 mm
27 mm
70 mm
50 mm
27 mm
IMPORTANT NOTE: UGT-MST210 card will onlysupport 50mm & 27mm card length.
mSATA Installation Steps
Verify the package contents.1.
Screws and washer for mounting M.2 card to PCB
Screws for mounting PCB to Plastic Mounting Board
Screws for mounting PCB to Plastic Mounting Board to 3.5” or 5.25” or custom mounting
Mounted Standard L bracket
PlasticMounting
Board
PCB
The device is ready to be integrated into your system.3.2.
12
Attached mSATA Device by inserting the mSATA Card and securing the using the latch to lock or using the washer and screw to hold the mSATA card in place.
-
Installation Guide
Information in this document is subject to change without notice.Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in ChinaPrinted on Recycled Paper. Copyright © 2016 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
Model: UGT-MST110, UGT-MST210, UGT-M2ST120, UGT-M2S220
www.vantecusa.com
Mount using Standard L bracket.
a) The card comes mounted on a Standard L bracket, nothing need to be done.
1.
Mounted Standard L bracket
Mounting into 3.5” Drive Bay.
a) Remove the two screws holding the Standard L bracket.
b) Secure the PCB to the Plastic Mounting plate. Align the 4 stand off to the mounting hole with the 4provided screws as shown,
c) Secure the Plastic Mounting Plate to the 3.5” Drive Bay using the provided 4 screws.
2.
Mounted Standard L bracketa)
Screws for mounting PCB to Plastic Mounting Boardb)
3.5” Drive Bay
c)Screws for mounting Plastic Mounting Board to 3.5” or 5.25” or custom mounting
Custom Mounting.
a) Please refer to the technical drawing on our website product page for detail measurement of the mounting.
4.
www.vantecusa.com
Mounting into 5.25” Drive Bay.(Optional accessories may be required depending on the design of your 5.25” Drive Bay)
a) Remove the two screws holding the Standard L bracket.
b) Secure the PCB to the Plastic Mounting plate. Align the 4 stand off to the mounting hole with the 4 provided screws as shown.
c) If your 5.25" Drive Bay have the necessary screws hole to secure a 2.5" HDD, you can secure this Plastic Mounting Board (with the PCB mounted) to this 5.25" Drive Bay.
d) If your 5.25" Drive Bay do not have the necessary screws hole to secure a 2.5" HDD, you will need to secure this Plastic Mounting Board (with the PCB mounted) to a 3.5" Drive Bay kit before securing to the 5.25" Drive Bay.
3.
3.5” Drive Bay
3.5” Drive Bay
5.25” Drive Bay
-
alvinTypewritten textUGT-MST210
top related