neo naviguide - neobiotechnas.neobiotech.co.kr/170430/pn2_neonaviguide_drilling...cortical tap...
Post on 02-Mar-2021
10 Views
Preview:
TRANSCRIPT
Neo NaviGuide
P E R F E C T I M P L A N T P L A N N I N G F O R B R I G H T S M I L E
Neo NaviGuide Kit Drilling Protocol April 24, 2017
Fixture Stop
Mount
Ø3.0 Drill
+
Ø2.2 Point Drill
Initial Drill Ø2.2 Drill
800~1,200rpm / 30~45Ncm 50~100rpm / 30~45Ncm
(Option : 800~1,200rpm / 30~45Ncm)
30~50rpm / 30~45Ncm
Fixture Non Stop Mount
Drilling Speed & Torque
Cortical Tap IS-III Ø3.5
Cortical Tap IS-II Ø3.5
Fixture Driver Contra Angle
Fixture Driver Rachet
Precautions
1. Must use drill with cold saline.
2. Must use Tap Drill in the case of D1~2 bone. 3. In the case that Sleeve Offset is applied, use the Fixture Nonstop mount when placing implant. 4. Must check the insertion torque after removing the guide. In the case of low insertion torque value, insert the implant slightly more. On the other hand, if the torque value is over 40Ncm, counterturn about 45˚~90˚, then double-check the torque value. 5. Must use Bone Profile after removing the guide. 6. Recommended use of Fixture Driver is to use after removing the guide for measuring the torque value or for further inserting the implant. of Surgical Guide. As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Cortical Tap
Cortical Drill
Fixture Stop
Mount
Bone Profile
Ø3.0 Drill
Ø3.5 Drill
Ø4.0 Drill
Ø4.5 Drill
Ø4.3 Tissue Punch
Ø2.2 Point Drill
Bone Trimmer
Initial Drill Ø2.2 Drill
800~1,200rpm / 30~45Ncm 50~100rpm / 30~45Ncm
(Option : 800~1,200rpm / 30~45Ncm)
30~50rpm / 30~45Ncm 50rpm
Drilling Speed & Torque
Fixture NonStop Mount
R/W
Fixture Driver Contra Angle
Fixture Driver Rachet
Precautions
1. Must use drill with cold saline.
2. Must use Tap Drill in the case of D1~2 bone. 3. In the case that Sleeve Offset is applied, use the Fixture Nonstop mount when placing implant. 4. Must check the insertion torque after removing the guide. In the case of low insertion torque value, insert the implant slightly more. On the other hand, if the torque value is over 40Ncm, counterturn about 45˚~90˚, then double-check the torque value. 5. Must use Bone Profile after removing the guide. 6. Recommended use of Fixture Driver is to use after removing the guide for measuring the torque value or for further inserting the implant. of Surgical Guide. As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
1.2mm (Tip Length)
8.5mm (Fixture Length)
9mm (Sleeve Offset)
#
Ø3.5 x 8.5mm / Offset 0mm
= 18.7mm (Drill Length)
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
Ø3.0 8.5mm Drill
Ø3.5 Cortical Tap (Option* ) 1
Fixture Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
1.2mm (Tip Length)
8.5mm (Fixture Length)
= 20.2mm (Drill Length)
10.5mm (Sleeve Offset)
#
Ø3.5 x 8.5mm / Offset +1.5mm
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 10mm Drill
Ø3.0 10mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 21.7mm (Drill Length)
#
Ø3.5 x 8.5mm / Offset +3.0mm
1.2mm (Tip Length)
8.5mm (Fixture Length)
12mm (Sleeve Offset)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 11.5mm Drill
Ø3.0 11.5mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
1.2mm (Tip Length)
10mm (Fixture Length)
= 20.2mm (Drill Length)
9mm (Sleeve Offset)
#
Ø3.5 x 10mm / Offset 0mm
Ø3.5 Cortical Tap (Option* ) 1
Fixture Stop Mount
Ø2.2 10mm Drill
Ø3.0 10mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 21.7mm (Drill Length)
#
Ø3.5 x 10mm / Offset +1.5mm
10.5mm (Sleeve Offset)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 11.5mm Drill
Ø3.0 11.5mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
1.2mm (Tip Length)
10mm (Fixture Length)
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 23.2mm (Drill Length)
#
Ø3.5 x 10mm / Offset +3.0mm
12mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 21.7mm (Drill Length)
#
Ø3.5 x 11.5mm / Offset 0mm
9mm (Sleeve Offset)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Stop Mount
Ø2.2 11.5mm Drill
Ø3.0 11.5mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
1.2mm (Tip Length)
11.5mm (Fixture Length)
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 23.2mm (Drill Length)
#
Ø3.5 x 11.5mm / Offset +1.5mm
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 24.7mm (Drill Length)
#
Ø3.5 x 11.5mm / Offset +3.0mm
12mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 14.5mm Drill
Ø3.0 14.5mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 23.2mm (Drill Length)
#
Ø3.5 x 13mm / Offset 0mm
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Stop Mount
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 24.7mm (Drill Length)
#
Ø3.5 x 13mm / Offset +1.5mm
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 14.5mm Drill
Ø3.0 14.5mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
= 23.2mm (Drill Length)
#
Ø3.5 x 13mm / Offset 0mm
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Ø3.5 Cortical Tap (Option* ) 1
Fixture Stop Mount
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 Point Drill
Ø2.2 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone Use IS-II Tap for inserting IS-II Fixture Use IS-III Tap for inserting IS-III Fixture
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 8.5mm / Offset 0mm
= 18.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Fixture Stop Mount
Mount Remover (Option* ) 1
Ø4.3 Tissue Punch (Option)
Ø2.2 8.5mm Drill
Ø3.0 8.5mm Drill
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 8.5mm / Offset +1.5mm
= 20.2mm (Drill Length)
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Bone Trimmer
1.5mm Offset (Option)
Fixture Non Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 10mm Drill
Ø3.0 10mm Drill
Ø2.2 7.3mm Drill
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 8.5mm / Offset +3.0mm
= 21.7mm (Drill Length)
12mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Bone Trimmer
3mm Offset (Option)
Fixture Non Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 11.5mm
Drill
Ø3.0 11.5mm
Drill
Ø2.2 7.3mm Drill
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 10mm / Offset 0mm
= 20.2mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Fixture Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 10mm Drill
Ø3.0 10mm Drill
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 10mm / Offset +1.5mm
= 21.7mm (Drill Length)
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Fixture Non Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 11.5mm
Drill
Ø3.0 11.5mm
Drill
Ø2.2 7.3mm Drill
Bone Trimmer
1.5mm Offset (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 10mm / Offset +3.0mm
= 23.2mm (Drill Length)
12mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Fixture Non Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 7.3mm Drill
Bone Trimmer
3mm Offset (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 11.5mm / Offset 0mm
= 20.2mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Fixture Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 11.5mm
Drill
Ø3.0 11.5mm
Drill
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 11.5mm / Offset +1.5mm
10.5mm (Sleeve Offset)
11.5mm (Fixture Length)
Mount Remover (Option* ) 1
= 22.2mm (Drill Length)
1.2mm (Tip Length)
Ø2.2 Point Drill
Fixture Non Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 7.3mm Drill
Bone Trimmer
1.5mm Offset (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø2.2 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø3.5 x 13mm / Offset 0mm
= 23.2mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Mount Remover (Option* ) 1
Ø2.2 Point Drill
Fixture Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 13mm Drill
Ø3.0 13mm Drill
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
*1 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. * Use of Tissue Punch and Bone Trimmer is optional. This may result in excessive removal of soft or hard tissue.
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 7.3mm / Offset 0mm
Bone Profile
(Option* ) 3
= 17.5mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
7.3mm (Fixture Length)
Ø2.2 Point Drill
Fixture Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
Ø3.0 7.3mm Drill
Ø3.5 7.3mm Drill
Ø4.0 Cortical Tap (Option* ) 1
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 7.3mm / Offset +1.5mm
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
10.5mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 8.5mm Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 7.3mm / Offset +3.0mm
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
12mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 10mm Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 8.5mm / Offset 0mm
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Ø2.2 8.5mm Drill
Bone Trimmer Standard (Option)
Fixture Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 8.5mm / Offset +1.5mm
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 10mm Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 8.5mm / Offset +3.0mm
Bone Profile
(Option* ) 3
= 21.7mm (Drill Length)
12mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 11.5mm
Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 10mm / Offset 0mm
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Ø2.2 10mm Drill
Bone Trimmer Standard (Option)
Fixture Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 10mm / Offset +1.5mm
Bone Profile
(Option* ) 3
10.5mm (Sleeve Offset)
= 21.7mm (Drill Length) 1.2mm (Tip Length)
10mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 11.5mm
Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 10mm / Offset +3.0mm
Bone Profile
(Option* ) 3
12mm (Sleeve Offset)
= 23.2mm (Drill Length) 1.2mm (Tip Length)
10mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 13mm Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 11.5mm / Offset 0mm
Bone Profile
(Option* ) 3
= 21.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.0 Cortical Tap (Option* ) 1
Ø2.2 11.5mm
Drill
Bone Trimmer Standard (Option)
Fixture Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 11.5mm / Offset +1.5mm
Bone Profile
(Option* ) 3
10.5mm (Sleeve Offset)
= 23.2mm (Drill Length) 1.2mm (Tip Length)
11.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 13mm Drill
Fixture Non Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
Mount Remover (Option* ) 2
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.0 x 13mm / Offset 0mm
Bone Profile
(Option* ) 3
= 23.2mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.0 Cortical Tap (Option* ) 1
Ø2.2 13mm Drill
Bone Trimmer Standard (Option)
Fixture Stop Mount
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
2
R/W
#
Ø4.5 x 7.3mm / Offset 0mm
Mount Remover (Option* ) 2
= 17.5mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
7.3mm (Fixture Length)
Bone Profile
(Option* ) 3
Ø2.2 Point Drill
Fixture Stop Mount
Ø4.3 Tissue Punch (Option)
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
Ø3.0 7.3mm Drill
Ø3.5 7.3mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Ø4.0 7.3mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 7.3mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
10.5mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 8.5mm Drill
Fixture Non Stop Mount
Ø4.0 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 7.3mm / Offset +3.0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
12mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 10mm Drill
Fixture Non Stop Mount
Ø4.0 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 8.5mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Ø2.2 8.5mm Drill
Bone Trimmer Standard (Option)
Fixture Stop Mount
Ø4.0 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 8.5mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 10mm Drill
Fixture Non Stop Mount
Ø4.0 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 8.5mm / Offset +3.0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 21.7mm (Drill Length)
12mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 11.5mm
Drill
Fixture Non Stop Mount
Ø4.0 11.5mm
Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 10mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Ø2.2 10mm Drill
Bone Trimmer Standard (Option)
Ø4.0 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 10mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
10.5mm (Sleeve Offset)
= 21.7mm (Drill Length) 1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Non Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 11.5mm
Drill
Ø4.0 11.5mm
Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 10mm / Offset +3.0mm
Mount Remover (Option* ) 2
12mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Non Stop Mount
Bone Profile
(Option* ) 3
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 13mm Drill
Ø4.0 13mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 11.5mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Fixture Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø4.5 Cortical Tap (Option* ) 1
Ø2.2 11.5mm
Drill
Bone Trimmer Standard (Option)
Ø4.0 11.5mm
Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 11.5mm / Offset +1.5mm
Mount Remover (Option* ) 2
10.5mm (Sleeve Offset)
= 23.2mm (Drill Length) 1.2mm (Tip Length)
11.5mm (Fixture Length)
Fixture Non Stop Mount
Bone Profile
(Option* ) 3
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 13mm Drill
Ø4.0 13mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø3.5 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø4.5 x 13mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Fixture Stop Mount
= 23.2mm (Drill Length)
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø4.5 Cortical Tap (Option* ) 1
Ø2.2 13mm Drill
Bone Trimmer Standard (Option)
Ø4.0 13mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 7.3mm / Offset 0mm
2
Mount Remover (Option* ) 2
= 17.5mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
7.3mm (Fixture Length)
Bone Profile
(Option* ) 3
Fixture Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch (Option)
Ø2.2 7.3mm Drill
Bone Trimmer Standard (Option)
Ø3.0 7.3mm Drill
Ø3.5 7.3mm Drill
Ø4.0 7.3mm Drill
Ø5.0 Cortical Tap (Option* ) 1
Ø4.5 7.3mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 7.3mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 18.7mm (Drill Length)
10.5mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø5.0 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 8.5mm Drill
Ø4.0 8.5mm Drill
Ø4.5 8.5mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 7.3mm / Offset +3.0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
12mm (Sleeve Offset)
0.9mm (Tip Length)
7.3mm (Fixture Length)
Ø5.0 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 10mm Drill
Ø4.0 10mm Drill
Ø4.5 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 8.5mm / Offset 0mm
Mount Remover (Option* ) 2
= 18.7mm (Drill Length)
9mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø5.0 Cortical Tap (Option* ) 1
Fixture Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 8.5mm Drill
Ø3.5 8.5mm Drill
Ø2.2 8.5mm Drill
Bone Trimmer Standard (Option)
Ø4.0 8.5mm Drill
Ø4.5 8.5mm Drill
Bone Profile
(Option* ) 3
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 8.5mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 20.2mm (Drill Length)
10.5mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø5.0 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 10mm Drill
Ø4.0 10mm Drill
Ø4.5 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 8.5mm / Offset +3.0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
= 21.7mm (Drill Length)
12mm (Sleeve Offset)
1.2mm (Tip Length)
8.5mm (Fixture Length)
Ø5.0 Cortical Tap (Option* ) 1
Fixture Non Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 11.5mm
Drill
Ø4.0 11.5mm
Drill
Ø4.5 11.5mm
Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 10mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Stop Mount
Ø5.0 Cortical Tap (Option* ) 1
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 10mm Drill
Ø3.5 10mm Drill
Ø2.2 10mm Drill
Bone Trimmer Standard (Option)
Ø4.0 10mm Drill
Ø4.5 10mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
R/W
#
Ø5.0 x 10mm / Offset +1.5mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
10.5mm (Sleeve Offset)
= 21.7mm (Drill Length) 1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Non Stop Mount
Ø5.0 Cortical Tap (Option* ) 1
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 11.5mm
Drill
Ø4.0 11.5mm
Drill
Ø4.5 11.5mm
Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 10mm / Offset +3.0mm
Mount Remover (Option* ) 2
12mm (Sleeve Offset)
1.2mm (Tip Length)
10mm (Fixture Length)
Fixture Non Stop Mount
Bone Profile
(Option* ) 3
Ø5.0 Cortical Tap (Option* ) 1
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Bone Trimmer
3.0mm Offset (Option)
Ø2.2 13mm Drill
Ø4.0 13mm Drill
Ø4.5 13mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 11.5mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
11.5mm (Fixture Length)
Fixture Stop Mount
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 11.5mm
Drill
Ø3.5 11.5mm
Drill
Ø2.2 11.5mm
Drill
Bone Trimmer Standard (Option)
Ø4.0 11.5mm
Drill
Ø4.5 11.5mm
Drill
Ø5.0 Cortical Tap (Option* ) 1
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 11.5mm / Offset +1.5mm
Mount Remover (Option* ) 2
10.5mm (Sleeve Offset)
= 23.2mm (Drill Length) 1.2mm (Tip Length)
11.5mm (Fixture Length)
Bone Profile
(Option* ) 3
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Bone Trimmer
1.5mm Offset (Option)
Ø2.2 13mm Drill
Ø4.0 13mm Drill
Ø4.5 13mm Drill
Fixture Non Stop Mount
Ø5.0 Cortical Tap (Option* ) 1
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
※ In soft(D4) bone or in condition of getting initial fixation at implant apex, Ø4.0 drill is the final drill ※ The fixture bigger than ∅4.5 diameter is recommended to be placed in posterior area
R/W
#
Ø5.0 x 13mm / Offset 0mm
Mount Remover (Option* ) 2
Bone Profile
(Option* ) 3
9mm (Sleeve Offset)
1.2mm (Tip Length)
13mm (Fixture Length)
Fixture Stop Mount
= 23.2mm (Drill Length)
Ø5.0 Cortical Tap (Option* ) 1
Ø2.2 Point Drill
Ø4.3 Tissue Punch
Ø2.2 7.3mm Drill
Ø3.0 13mm Drill
Ø3.5 13mm Drill
Ø2.2 13mm Drill
Bone Trimmer Standard (Option)
Ø4.0 13mm Drill
Ø4.5 13mm Drill
*1 Use Tap Drill in the case of D1 ~ D2 bone *2 Use Mount Remover for removing the Fixture Mount from placed implant Remove the Fixture Mount from the implant by first removing the screw of the Mount, and then connecting the Mount Remover and rotating it clockwise. *3 Use Bone Profile after removing the guide
* As the Sleeve Offset Marking is only applied for the standard 9mm, please be cautious when the Sleeve Offset is applied.
GUIDE NeoNaviGuide
PM / GUIDE PM TEAM
neobiotech.co.kr │ +82-2-582-2885
top related