nutiny-sdk-nano130 user manual - nuvoton · nutiny-sdk-nano130 user manual jan. 8, 2013 3 revision...
Post on 08-Aug-2018
227 Views
Preview:
TRANSCRIPT
NuTiny-SDK-Nano130 User Manual
ARM Cortex™-M0
32-bit Microcontroller
Jan. 8, 2013 Revision V1.01
NuTiny-SDK-Nano130 User Manual for NuMicro
™ Nano130 Series
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro™
microcontroller based system design. Nuvoton
assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 2 Revision V1.01
Table of Contents
1 Overview .................................................................................................... 3
2 Introduction to NuTiny-SDK-Nano130 ................................................................. 3
2.1 NuTiny-SDK-Nano130 Jumper Description ................................................................. 4 2.2 Pin Assignment for Extended Connectors .................................................................. 5 2.3 NuTiny-SDK-Nano130 PCB Placement ..................................................................... 7
3 Starting to Use NuTiny -SDK-Nano130 on the Keil μVision® IDE ................................. 8
3.1 Downloading and Installing Keil μVision® IDE Software ................................................... 8
3.2 Downloading and Installing Nuvoton Nu-Link Driver ....................................................... 8 3.3 Hardware Setup ................................................................................................. 8 3.4 LCD_DEMO Example Program ............................................................................... 9
4 Starting to Use NuTiny-SDK-Nano130 on the IAR Embedded Workbench.................... 10
4.1 Downloading and Installing IAR Embedded Workbench Software .................................... 10 4.2 Downloading and Installing Nuvoton Nu-Link Driver ..................................................... 10 4.3 Hardware Setup ............................................................................................... 10 4.4 LCD_DEMO Example Program ............................................................................. 11
5 NuTiny-EVB-Nano130 Schematics ................................................................... 12
6 Downloading NuMicro™
Related Files from Nuvoton Website ................................... 14
6.1 Downloading NuMicro™
Keil μVision® IDE Driver ......................................................... 14
6.2 Downloading NuMicro™
IAR EWARM Driver .............................................................. 16 6.3 Downloading NuMicro
™ Nano100 series BSP Software Library ....................................... 18
7 Revision History ......................................................................................... 19
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 3 Revision V1.1
1 Overview The NuTiny-SDK-Nano130 is a specific development tool for the NuMicro Nano130 series
users to develop and verify the application program easily. The NuTiny-SDK-Nano130
includes two portions: NuTiny-EVB-Nano130 (an evaluation board) and Nu-Link-Me (its
Debug Adaptor), such that users do not need additional ICE or debug equipment.
2 Introduction to NuTiny-SDK-Nano130 The NuTiny-SDK-Nano130 uses the NANO130KE3BN as the target microcontroller. Figure
2-1 shows the NuTiny-SDK-Nano130 for Nano130 series, in which the left portion is called
NuTiny-EVB-Nano130 and the right portion is called Nu-Link-Me.
The NuTiny-EVB-Nano130 is similar to other development boards, by which users can
develop and verify applications to emulate the real behavior. The on board chip covers
Nano130 series features. The NuTiny-EVB-Nano130 can be a real system controller to design
the users’ target systems.
The Nu-Link-Me is a Debug Adaptor, which connects your PC's USB port to a target system
(via Serial Wired Debug Port) and allows you to program and debug embedded programs on
the target hardware. To use the Nu-Link-Me Debug adaptor with IAR or Keil, please refer to
“Nuvoton NuMicro™ IAR ICE Driver User Manual” or “Nuvoton NuMicro™ Keil ICE Driver User
Manual” for details. The two documents will be stored in the local hard disk when each is
installed.
LQFP-128 pin
Extended ConnectorVDD33
GND ICE Controller
USB Connector
J2
ICE Controller
LQFP-128 pin
Extended Connector
JP16JP17
JP15 JP11
Target Chip
USB Connector
Reset Key
PC12 Key
J1
LCD Panel
Figure 2-1 NuTiny-SDK-Nano130 (Yellow PCB Board)
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 4 Revision V1.01
2.1 NuTiny-SDK-Nano130 Jumper Description
2.1.1 Power Settings
J1: USB port in NuTiny-EVB-Nano130
JP2: VDD33 Voltage connector in NuTiny-EVB-Nano130
J2: USB port in Nu-Link-Me
Power Model J2 USB Port J1 USB Port JP2 VDD33 MCU Voltage
Model 1 Connect to PC X DC 3.3V output DC 3.3V
Model 2 X Connect to PC DC3.3V output DC 3.3V
Model 3 X X DC 1.8 V ~ 3.6 V Input
DC 1.8 V ~ 3.6 V Decided by JP2 VDD33 Input
X: Unused.
2.1.2 Debug Connectors
JP4: Connector in target board (NuTiny-EVB-Nano130) for connecting with Nuvoton ICE adaptor (Nu-Link-Me)
JP8: Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board (e.g. NuTiny-EVB-Nano130)
2.1.3 USB Connectors
J1: Mini USB Connector in NuTiny-EVB-Nano130 for application use
J2: Mini USB Connector in Nu-Link-Me connected to a PC USB port
2.1.4 Extended Connectors
JP11, JP15, JP16 and JP17: Show all chip pins in NuTiny-EVB-Nano130
2.1.5 Buttons
SW1: Reset button in NuTiny-EVB-Nano130
SW2: PC12 button in NuTiny-EVB-Nano130
2.1.6 Power Connectors
JP2: VDD33 connector in NuTiny-EVB-Nano130
JP3: GND connector in NuTiny-EVB-Nano130
2.1.7 Power Jumpers
JP1: Jumper in ICE adaptor (Nu-Link-Me) for power source selection of JP8.
JP9: Jumper in NuTiny-EVB-Nano130 to set power source from JP4 and J1
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 5 Revision V1.01
2.2 Pin Assignment for Extended Connectors
The NuTiny-EVB-Nano130 provides the NANO130KE3BN target chip on board and the
extended connectors (JP11, JP15, JP16 and JP17) for LQFP128-pin.
No Pin Name No Pin Name No Pin Name No Pin Name
01 PE13/ LCD_SEG27 33 PE12/UART1_CTSn 65 PE4/SPI0_MOSI0 97 VREF
02 PB14/INT0/SC2_CD/ SPI2_SS1/LCD_SEG12/
LCD_SEG26
34 PE11/UART1_RTSn 66 PE3/SPI0_MISO0 98 NC
03 PB13/EBI_AD1/ LCD_SEG11/LCD_SEG25
35 PE10/UART1_TXD 67 PE2/SPI0_CLK 99 AVDD
04 PB12/EBI_AD0/ CLKO/LCD_SEG10/
LCD_SEG24
36 PE9/UART1_RXD 68 PE1/PWM1_CH3/SPI0_SS0 100 PD0/UART1_RXD/ SPI2_SS0/SC1_CLK/
CTK0/AD8
05 NC 37 PE8/LCD_SEG9 69 PE0/PWM1_CH2/ I2S_MCLK
101 PD1/UART1_TXD/ SPI2_CLK/SC1_DAT/
AD9/CTK1
06 X320 38 PE7/LCD_SEG8 70 PC13/SPI_MOSI1/ PWM1_CH1/SNOOPER/
INT0/I2C0_SCL
102 PD2/UART1_RTSn/ I2S_LRCLK/SPI2_MISO0/
SC1_PWR/AD10/CTK2
07 X32I 39 NC 71 PC12/SPI1_MISO1/ PWM1_CH0/
INT0/I2C0_SDA
103 PD3/UART1_CTSn/ I2S_BCLK/SPI2_MOSI0/ SC1_RST/AD11/CTK3
08 NC 40 NC 72 PC11/SPI1_MOSI0/ UART1_TXD/
CTK15/LCD_SEG31
104 NC
09 PA11/I2C1_SCL/EBI_nRD/ SC0_RST/SPI2_MOSI0/ LCD_SEG9/LCD_SEG23
41 NC 73 PC10/SPI1_MISO0/ UART1_RXD/
CTK14/LCD_SEG30
105 PD4/I2S_DI/ SPI2_MISO1/SC1_CD/
CTK4/LCD_SEG35
10 PA10/I2C1_SDA/EBI_nWR/ SC0_PWR/SPI2_MISO0/ LCD_SEG8/LCD_SEG22
42 NC 74 PC9/SPI1_CLK/I2C1_SCL/ CTK13/LCD_SEG29
106 PD5/I2S_DO/ SPI2_MOSI1/CTK5/
LCD_SEG34
11 PA9/I2C0_SCL/ SC0_DAT/SPI2_CLK/
LCD_SEG7/LCD_SEG21
43 NC 75 PC8/SPI1_SS0/ EBI_MCLK/I2C1_SDA/ CTK12/LCD_SEG28
107 PC7/DA1_OUT/ EBI_AD5/TC1/
PWM0_CH1/LCD_SEG17
12 PA8/I2C0_SDA/ SC0_CLK/SPI2_SS0/
LCD_SEG6/LCD_SEG20
44 PB0/UART0_RXD/ SPI1_MOSI0/
LCD_SEG1/LCD_SEG7
76 PA15/PWM0_CH3/ I2S_MCLK/TC3/SC0_PWR/ UART0_TXD/LCD_SEG27
108 PC6/DA0_OUT/ EBI_AD4/TC0/
SC1_CD/PWM0_CH0
13 PD8/LCD_SEG19 45 PB1/UART0_TXD/ SPI1_MISO0/
LCD_SEG0/LCD_SEG6
77 PA14/PWM0_CH2/ EBI_AD15/TC2/
UART0_RXD/LCD_SEG26
109 PC15/EBI_AD3/ TC0/PWM1_CH2/
LCD_SEG16/LCD_SEG33
14 PD9/LCD_SEG18 46 PB2/UART0_RTSn/ EBI_nWRL/SPI1_CLK/ LCD_COM3/LCD_SEG
5
78 PA13/PWM0_CH1/ EBI_AD14/TC1/I2C0_SCL/
CTK11/LCD_SEG25
110 PC14/EBI_AD2/ PWM1_CH3/
LCD_SEG15/LCD_SEG32
15 PD10/LCD_SEG17 47 PB3/UART0_CTSn/ EBI_nWRH/SPI1_SS0/ LCD_COM2/LCD_SEG
4
79 PA12/PWM0_CH0/ EBI_AD13/TC0/I2C0_SDA/
CTK10/LCD_SEG24
111 PB15/INT1/ SNOOPER/
LCD_SEG14/LCD_SEG31
16 PD11/LCD_SEG16 48 PD6/LCD_SEG3 80 PF0/ICE_DAT/INT0 112 NC
17 PD12/LCD_SEG15 49 PD7/LCD_SEG2 81 PF1/ICE_CLK/ CLKO/INT1
113 XT1_IN
18 PD13/LCD_SEG14 50 PD14/LCD_SEG1 82 NC 114 XT1_OUT
19 PB4/UART1_RXD/ SC0_CD/SPI2_SS0/
LCD_SEG5/LCD_SEG13
51 PD15/LCD_SEG0 83 VDD 115 NC
20 PB5/UART1_TXD/ 52 PC5/SPI0_MOSI1/ 84 NC 116 nRESET
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 6 Revision V1.01
SC0_RST/SPI2_CLK/ LCD_SEG4/LCD_SEG12
LCD_COM3
21 PB6/UART1_RTSn/ EBI_ALE/SPI2_MISO0/
LCD_SEG3/LCD_SEG11
53 PC4/SPI0_MISO1/ LCD_COM2
85 VSS 117 VSS
22 PB7/UART1_CTSn/ EBI_nCS/SPI2_MOSI0/
LCD_SEG2/LCD_SEG10
54 PC3/SPI0_MOSI0/ I2S_DO/SC1_RST/
LCD_COM1
86 VSS 118 VSS
23 NC 55 PC2/SPI0_MISO0/ I2S_DI/SC1_PWR/
LCD_COM0
87 AVSS 119 NC
24 LDO_CAP 56 PC1/SPI0_CLK/ I2S_BCLK_SC1_DAT/
LCD_DH2
88 AVSS 120 VDD
25 NC 57 PC0/SPI0_SS0/ I2S_LRCLK/
SC1_CLK/LCD_DH1
89 PA0/AD0/ SC2_CD/CTK8
121 NC
26 NC 58 PE6 90 PA1/AD1/EBI_AD12/CTK9 122 PF4/I2C0_SDA/CTK6
27 VDD 59 LCD_VLCD 91 PA2/AD2/EBI_AD11/ UART1_RXD/LCD_SEG23
123 PF5/I2C0_SCL/CTK7
28 NC 60 LCD_VLCD 92 PA3/AD3/EBI_AD10/ UART1_TXD/LCD_SEG22
124 VSS
29 VSS 61 PE5 93 PA4/AD4/EBI_AD9/ SC2_PWR/I2C0_SDA/
LCD_SEG21/LCD_SEG39
125 PVSS
30 VSS 62 PB11/PWM1_CH0/ TM3/SC2_DAT/
SPI0_MISO0/LCD_V1
94 PA5/AD5/EBI_AD8/ SC2_RST_I2C0_SCL/
LCD_SEG20/LCD_SEG38
126 PB8/STADC/TM0/ INT0/SC2_PWR/
LCD_SEG13/LCD_SEG30
31 VSS 63 PB10/SPI0_SS1/ TM2/SC2_CLK/
SPI0_MOSI0/LCD_V2
95 PA6/AD6/EBI_AD7/ TC3/SC2_CLK/PWM0_CH3/ LCD_SEG19/LCD_SEG37
127 PE15/LCD_SEG29
32 VSS 64 PB9/SPI1_SS1/ TM1/SC2_RST/ INT0/LCD_V3
96 PA7/AD7/EBI_AD6/ TC2/SC2_DAT/
PWM0_CH2/CTK_CAP/ LCD_SEG18/LCD_SEG36
128 PE14/LCD_SEG28
Table 2-1 NANO130KE3BN LQFP 128-pin Assignment for Extended Connectors
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 7 Revision V1.01
2.3 NuTiny-SDK-Nano130 PCB Placement
The following figure shows the NuTiny-SDK-Nano130 PCB placement.
Figure 2-2 NuTiny-SDK-Nano130 PCB Placement
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 8 Revision V1.01
3 Starting to Use NuTiny -SDK-Nano130 on the Keil μVision® IDE
3.1 Downloading and Installing Keil μVision® IDE Software
Please connect to the Keil company website (http://www.keil.com) to download the Keil
μVision® IDE and install the RVMDK.
3.2 Downloading and Installing Nuvoton Nu-Link Driver
Please connect to Nuvoton NuMicro™ website (http://www.nuvoton.com/NuMicro) to
download the “NuMicro™ Keil μVision®
IDE driver” file. Please refer to section 6.1 for the
detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and
execute the “Nu-Link_Keil_Driver.exe” to install the driver.
3.3 Hardware Setup
The hardware setup is shown in the following figure.
Figure 3-1 NuTiny-SDK-Nano130 Hardware Setup
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 9 Revision V1.01
3.4 LCD_DEMO Example Program
This example, as shown in the directory of Figure 3-2, demonstrates the download and
debugging of an application on a NuTiny-SDK-Nano130 board. The example file can be
downloaded from Nuvoton NuMicro™ website as described in 6.3 Downloading NuMicro™
Nano100 series BSP Software Library.
Directory Project File
Figure 3-2 LCD_DEMO Example Directory
To use this example:
The LCD panel on the NuTiny-EVB-Nano130 board will display a NUVOTON logo.
Start μVision®
Project-Open
Open the LCD_DEMO.uvproj project file
Project - Build
Compile and link the LCD_DEMO application
Flash – Download
Program the application code into on-chip Flash
ROM
Start Debug mode
When using the debugger commands, you may:
Review variables in the watch window
Single step through code
Reset the device
Run the application
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 10 Revision V1.01
4 Starting to Use NuTiny-SDK-Nano130 on the IAR Embedded Workbench
4.1 Downloading and Installing IAR Embedded Workbench Software
Please connect to IAR company website (http://www.iar.com) to download the IAR
Embedded Workbench and install the EWARM.
4.2 Downloading and Installing Nuvoton Nu-Link Driver
Please connect to Nuvoton Company NuMicro™
website (http://www.nuvoton.com/NuMicro)
to download the “NuMicro™
IAR ICE Driver User Manual” file. Please refer to section 6.2 for
the detailed download flow. When the Nu-Link driver has been well downloaded, please
unzip the file and execute the “Nu-Link_IAR_Driver.exe” to install the driver.
4.3 Hardware Setup
The hardware setup is shown in the following figure.
Figure 4-1 NuTiny- SDK-Nano130 Hardware Setup
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 11 Revision V1.01
4.4 LCD_DEMO Example Program
The example, as shown in the directory of Figure 4-2, demonstrates the download and
debugging of an application on a NuTiny-SDK-Nano130 board. The example file can be
downloaded from Nuvoton NuMicro™ website as described in 6.3 Downloading NuMicro™
Nano100 series BSP Software Library.
Directory Project File
Figure 4-2 LCD_DEMO Example Directory
To use this example:
The LCD panel on the NuTiny-EVB-Nano130 board will display a NUVOTON logo.
Start IAR Embedded Workbench
File-Open-Workspace
Open the LCD_DEMO.eww workspace file
Project - Make
Compile and link the LCD_DEMO application
Project – Download and Debug
Program the application code into on-chip
Flash ROM
Single step through code
Reset the device
Run the application
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 12 Revision V1.01
5 NuTiny-EVB-Nano130 Schematics
PIN27
PIN85
PIN
10
2
PIN
10
0
PIN86
PIN90PIN91
PIN89
PIN87PIN88
PIN
10
3P
IN1
04
PIN
10
5
PIN
10
1
PIN80
PIN83PIN82
PIN79
PIN76PIN77PIN78
PIN81
PIN92
PIN95PIN94PIN93
PIN28
PIN
10
7P
IN1
08
PIN
12
4
PIN
58
PIN
63
PIN
62
PIN
59
PIN
61
PIN
64
C130.1uFC0603
U1
NANO130_LQFP128
PB
.964
PB
.10
63
PB
.11
62
NC
60
PE
.658
PC
.057
PC
.156
PC
.255
PC
.354
PC
.453
PC
.552
PD
.15
51
PD
.14
50
PD
.749
PD
.648
PB
.347
PB
.246
PB
.145
PB
.044
US
B_
DP
43
US
B_
DM
42
VD
D3
341
VB
US
40
PE
.738
PE
.837
VSS29
NC26
NC23 PB.722 PB.621 PB.520 PB.419 PD.1318 PD.1217 PD.1116 PD.1015 PD.914 PD.813 PA.812 PA.911 PA.1010 PA.11
9
X32I7 X32O6
PB.124 PB.133 PB.142 PE.131
PE
.14
128
PE
.15
127
PB
.8126
PV
SS
125
PF
.5123
PF
.4122
VD
D120
VS
S117
RE
SE
T116
XT
1_
Ou
t114
XT
1_
In113
PB
.15
111
PC
.14
110
PC
.15
109
PC
.6108
PC
.7107
PD
.5106
PD
.4105
PD
.3103
PD
.2102
PD
.1101
PD
.0100
NC
98
VR
EF
97
PA.796
PA.695
PA.594
PA.493
PA.392
PA.291
PA.190
PA.089
AVSS87
VSS85
NC82
ICE_CK/PF.181
ICE_DAT/PF.080
PA.1279
PA.1378
PA.1477
PA.1576
PC.875
PC.974
PC.1073
PC.1172
PC.1271
PC.1370
PE.069
PE.168
PE.267
PE.366
PE.465
VDD83
VSS86
NC84
AVSS88
AV
DD
99
NC
112
NC
115
VS
S118
NC
119
NC
121
VS
S124
NC5
NC8
LDO24
NC25
VDD27
NC28
VSS30
VSS31
VSS32
PE
.12
33
PE
.11
34
PE
.10
35
PE
.936
NC
39
PE
.561
VL
CD
59
NC
104
PIN102
PIN104
PIN106
PIN108
PIN105
PIN103
PIN114
PIN107
PIN116
PIN113PIN112
PIN115
PIN110PIN111
PIN109
PIN124
PIN122
PIN118
PIN121
PIN123
PIN120
PIN117
PIN119
PIN126PIN127
PIN125
PIN128
JP9
HEADER 2PX1
1 2
PIN
12
1
Title
Size Document Number Rev
Date: Sheet of
NANO130KE3BN.SCH V1.1
NuTiny-EVB-Nano130-LQFP128 V1.1
Custom
2 3Tuesday , January 08, 2013
PIN1
TICE_DAT
PIN
44
TICE_DAT
PIN
11
7
PIN
12
0
TICE_RSTTICE_CLK
PIN
43
XTAL1
PIN5
PIN9
PIN26
PIN4
PIN7
PIN
11
8
TICE_RST
PIN
40
PIN12
PIN
11
9P
IN4
2
PIN8
PIN3
PIN
39
PIN
35
PIN
38
PIN6
TICE_RST
PIN11
PIN
41
XT
AL
2P
IN1
14
TICE_CLK
PIN
33
PIN
37
TICE_RST
PIN10
PIN2
XT
AL
1P
IN1
13
PIN90
PIN93
XTAL2
PIN86
PIN83
PIN24
PIN87
PIN91
PIN8
PIN82
PIN89PIN9
PIN1
PIN4
PIN7X32KI
PIN2
PIN85
PIN92
PIN84
PIN5
PIN3
PIN6X32KO
PIN24
PIN21PIN20
PIN18
PIN15
PIN17PIN16
PIN14PIN13PIN12PIN11PIN10
PIN21
PIN14
PIN25
PIN22
PIN13
PIN19
PIN15
PIN23
PIN17
PIN24
PIN20
PIN18
PIN16
PIN22
PIN19
DVDD
PIN
54
PIN
47
PIN
56
PIN
55
PIN
45
PIN
50
PIN
53
PIN
46
PIN
52
PIN
49
PIN
48
PIN
57
PIN
51
PIN96
TICE_DATPIN80PIN79
PIN94
PIN76
PIN73
PIN81 TICE_CLK
PIN74
PIN95
PIN77
PIN72
PIN78
PIN75
PIN88
PIN
36
PIN
12
5
PIN
10
6
PIN
11
2
PIN
12
8
PIN
12
6
PIN
11
0P
IN1
11
PIN
10
9
PIN
11
5
nINT0PIN71
R41M/DNE0603R
C110uF/10VTANT-A
SW2
PUSH BUTTONSW
X212MHzXTAL3-1
TP1SIP/1P
1
R2
330603R
TP3SIP/1P
1
JP3
HEADER 2PX1HEADER 2PX1
12
R110K0603R
JP4
HEADER 5PX2HEADER 5PX2
1 23 45 67 89 10
JP2
HEADER 2PX1HEADER 2PX1
12
C5
20pF0603C
C2
10uF/10VTANT-A
CB20.1uFC0603
CB30.1uFC0603
TP2SIP/1P
1
C3
20pF0603C
SW1
PUSH BUTTONSW
DVDD
DVDD
DVDD
TICE_RSTTICE_CLKTICE_DAT
Reset Circuit
ICE Interface
From ICE Bridge's USB Power
DVDD
C90.1uFC0603
PIN96
PIN99PIN98PIN97
PIN100
CB50.1uFC0603
DVDD
PIN
12
7
VDD33
C410uF/10VTANT-A
PIN
34
C121uFC0603
PIN64
PIN56
PIN62PIN61
PIN54
PIN52
PIN55
PIN60
PIN51
PIN63
PIN57
C141uFC0603
PIN53
PIN59PIN58
1 2
D1
SS24ARB060L
PIN30PIN31
C101uFC0603
PIN32
TIC
E_
RS
TP
IN1
16
R113300603R
VCC33(A)
VCC33(A)
PIN69
PIN65PIN66
PIN71
PIN67PIN68
PIN70
VDD33
VDD33VDD33
VDD33
PIN27PIN28PIN29
PIN34PIN33
PIN30
PIN32
PIN36
PIN38PIN37
PIN35
PIN41
PIN31
PIN39PIN40
PIN42
PIN46
PIN44
PIN49
PIN45
PIN47PIN48
PIN43
PIN50
DVDD
PIN58
12
IOKPT-2012KP-2012
PIN
12
3
C151uFC0603
PIN66PIN65
PIN74
PIN68PIN69PIN70
PIN67
PIN72PIN71
PIN73
VCC33(B) PIN
98
PIN84
PIN75
PIN[1..128]
PIN23
PIN
60
X32KO
X32KIC8
6pF0603C
C7
6pF0603C
Crystal
X132.768KHzXTAL3-1
DVDD
PIN
97
PIN
99
CB40.1uFC0603
PIN25
PIN
12
2
PIN29
PIN26
PIN101
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 13 Revision V1.01
PIN66PIN65
CTK15
CTK11
CTK14
K1CTKey _SLIDER
1 2
3 4 5
CTK13
CTK12
R14
100K
PIN26
VDD33
PIN27
PIN[1..128]
PIN29PIN31
PIN
41
PIN
33
PIN
52
PIN28
PIN2
PIN16
PIN30
PIN72
PIN
62
JP17
HEADER 16PX2
2 4 6 8 10
12
14
16
18
20
22
24
26
28
30
32
1 3 5 7 911
13
15
17
19
21
23
25
27
29
31
PIN9
PIN
43
PIN
42
PIN
57
PIN
37
PIN
54
PIN
53
PIN86
PIN
59
PIN
40
PIN
44
PIN
34
PIN
63
PIN32
PIN91
PIN
50
PIN
56
PIN
61
PIN
38
PIN
35
PIN22
PIN96
PIN
64
PIN
45
PIN
51
PIN
49
PIN
47
PIN
58
PIN3
PIN74
PIN
39
PIN
46
PIN
48
PIN
36
PIN
60
PIN78
PIN
55
PIN80
PIN92
PIN73
PIN24
PIN6
PIN93
PIN67PIN4
PIN79
PIN25
PIN84
PIN82
PIN85
PIN95
PIN75
PIN70
PIN14
PIN83
PIN15
PIN18
PIN90
PIN87
PIN7
PIN68
PIN13
PIN21
PIN94
PIN88
PIN19
PIN12
PIN89
PIN23
PIN76
PIN17
PIN1
PIN81
PIN20
PIN69
PIN71PIN8
PIN5
PIN11PIN10
PIN77
PIN91PIN93
PIN85
PIN78
PIN69
PIN76PIN73
PIN84
PIN77
PIN65
PIN95
PIN86
PIN94
PIN67
PIN72
PIN80
JP16
HEADER 16PX2
2468
101214161820222426283032
135791113151719212325272931
PIN81
PIN70
PIN88
PIN83PIN82
PIN66
PIN92
PIN87
PIN71
PIN68
PIN90
PIN74
PIN89
PIN96
PIN79
PIN75
PIN101
PIN121
PIN117
PIN102
PIN106
PIN110
PIN120PIN119
PIN112
PIN105
PIN128
PIN126
PIN109
PIN123
PIN127
PIN111
PIN124
PIN122
PIN116
PIN114
PIN107
PIN115
PIN104
PIN118
PIN125
PIN108
PIN113
PIN103
VBUSPIN40
USB_DP
R12330603R
L1L0603
R13330603R
J1
mini USB 5pinUSB_MINI_B
GND5 NC4 DP3 DM2 VCC1
SHIELD6
SHIELD7
SHIELD8
SHIELD9
PIN
125
PIN
118
PIN
128
PIN
109
PIN
112
PIN
111
PIN
126
PIN
101
PIN
120
PIN
103
PIN
123
PIN
119
PIN
99
PIN
124
USB_DM
PIN
113
PIN
97
PIN
115
PIN
117
PIN
100
PIN
116
PIN
107
PIN
102
PIN
122
PIN
114
PIN
127
PIN
98
PIN
110
PIN
108
PIN
106
PIN
105
PIN
121
PIN
104
JP11
HEADER 16PX2
246810
12
14
16
18
20
22
24
26
28
30
32
1357911
13
15
17
19
21
23
25
27
29
31
VCC33(B)
U4RT9164A-3.3V
IN3
GN
D1
OU
T2
OU
T4
CT410uF/10VTANT-A
Thermistor
C11
0.1uF
Title
Size Document Number Rev
Date: Sheet of
OTHER.SCH V1.0
NuTiny-EVB-Nano130-LQFP128 V1.0
Custom
3 3Thursday , July 19, 2012
PIN49
PIN53
PIN36
PIN62
PIN59
PIN56
PIN51
PIN47
PIN35
PIN38
PIN48
PIN37
PIN40
PIN55
PIN64
PIN43
PIN61
PIN44
PIN57
PIN45
PIN63
PIN46
PIN52
PIN42
PIN39
PIN58
PIN34
PIN60
PIN41
PIN54
PIN50
NTC1
100K
PIN43
ADC0
PIN42
PIN90
PIN2
PIN28
PIN21PIN19
PIN15
PIN30
PIN4
PIN20
PIN32
PIN25PIN23
PIN8
PIN26
PIN11PIN9
PIN13
PIN27
PIN17
PIN1
PIN7
PIN29
JP15
HEADER 16PX2
2468101214161820222426283032
13579
1113151719212325272931
PIN3
PIN22
PIN5
PIN12
PIN18
PIN6
PIN14
PIN31
PIN24
PIN16
PIN10
PIN
128
PIN
101
PIN
99
PIN
97
PIN
100
PIN
102
PIN
98
PIN89
PIN23
PIN9
PIN1
PIN22
PIN18
PIN24PIN21
PIN4
PIN25
PIN11
PIN17
PIN3
PIN12PIN14
PIN10
PIN19
PIN2
PIN15
PIN20
PIN8
PIN13
PIN7PIN5 PIN6
PIN16
PIN69
PIN65PIN67
PIN70
PIN66PIN68
PIN96
PIN32
PIN26
PIN31
PIN28PIN29PIN30
PIN27
PIN
112
PIN
103
PIN
124
PIN
115
PIN
116
PIN
114
PIN
108
PIN
121
PIN
118
PIN
126
PIN
119
PIN
122
PIN
110
PIN
105
PIN
125
PIN
111
PIN
123
PIN
113
PIN
117
PIN
107
PIN
127
PIN
106
PIN
104
PIN
109
PIN
120
PIN84
PIN94
PIN81PIN82
PIN71
PIN89
PIN76
PIN95
PIN72
PIN88
PIN92PIN90
PIN79
PIN91
PIN85
PIN73
PIN86
PIN80
PIN83
PIN87
PIN74PIN75
PIN93
PIN78 PIN77
PIN73
PIN72
PIN74
PIN75
PIN78
PIN98PIN97
PIN99PIN100
PIN
44
PIN
47
PIN
36
PIN
52
PIN
57
PIN
54
PIN
40
PIN
50
PIN
38
PIN
51
PIN
46
PIN
41
PIN
42
PIN
37
PIN
53
PIN
34
PIN
56
PIN
35
PIN
49
PIN
48
PIN
33
PIN
45
PIN
39
PIN
55
PIN
43
JP5
HEADER 16PX2, 2.00mm
2468101214161820222426283032
13579
1113151719212325272931
PIN
59
PIN
63
PIN
61
PIN
64
PIN
58
PIN
60
PIN
62
JP6
HEADER 16PX2, 2.00mm
2468
101214161820222426283032
135791113151719212325272931
JP7
HEADER 16PX2, 2.00mm
2 4 6 8 10
12
14
16
18
20
22
24
26
28
30
32
1 3 5 7 911
13
15
17
19
21
23
25
27
29
31
PIN33
JP1
HEADER 16PX2, 2.00mm
246810
12
14
16
18
20
22
24
26
28
30
32
1357911
13
15
17
19
21
23
25
27
29
31
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 14 Revision V1.01
6 Downloading NuMicro™ Related Files from Nuvoton Website
6.1 Downloading NuMicro™
Keil μVision® IDE Driver
Step 1
Visit the Nuvoton NuMicro™
website: http://www.nuvoton.com/NuMicro
Step 2
Click here to enter
Device Driver and
Software Library.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 15 Revision V1.01
Step 3
Step 4
Download the NuMicro Keil μVision® IDE driver.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 16 Revision V1.01
6.2 Downloading NuMicro™
IAR EWARM Driver
Step 1
Visit the Nuvoton NuMicro™ website: http://www.nuvoton.com/NuMicro
Step 2
Click here to enter
Device Driver and
Software Library.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 17 Revision V1.01
Step 3
Step 4
Download the NuMicro™ IAR Embedded Workbench® driver.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 18 Revision V1.01
6.3 Downloading NuMicro™ Nano100 series BSP Software Library
Step 1
Visit the Nuvoton NuMicro™ website: http://www.nuvoton.com/NuMicro
Step 2
Step 3
Download the NuMicro™ Nano100 series software library.
Click here to enter
Device Driver and
Software Library.
NuTiny-SDK-Nano130 User Manual
Jan. 8, 2013 19 Revision V1.01
7 Revision History
Revision Date Description
1.00 Oct. 16, 2012 Preliminary version
1.01 Jan. 8, 2013 Changed the value of C7 and C8 in the schematics from 10pF
to 6 pF
Important Notice
Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment
intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation
instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or
sustain life. Further more, Nuvoton products are not intended for applications wherein failure of Nuvoton products could
result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur.
Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Nuvoton for any damages resulting from such improper use or sales.
Please note that all data and specifications are subject to change without notice. All the trademarks of products and
companies mentioned in this datasheet belong to their respective owners.
top related