ofna dm one pro
Post on 14-Jun-2015
1.270 Views
Preview:
TRANSCRIPT
*High impact large front bumper and foam bumper.*CNC machined steel transmission bevel gears.*CNC machined aluminium front shock mount.*CNC machined aluminium rear shock mount with heat sink.*Low C. G. lay-down steering servo and throttle servo mount.*Front and rear push rod suspension design.*Threaded lay-down 13mm big bore shocks for front and rear. *Adjustable ackerman steering geometry design. *Graphite front plate.*Graphite low centre of gravity radio tray.*Front pivot ball suspension with dust boot covers.*Rear pivot ball uprights for quick geometry changes.*Spring steel universal joints for front and rear.*Adjustable blade type sway bar for front and rear.*Adjustable down-stop and up-stop suspension design. *CNC machined 7075-T6 hard coated chassis brace.
Features:*Quick release centre differential mount design.*Convenient carry handle In the centre of the car.*Changeable roll centre design for front and rear suspension.*CNC machined steel brake discs.*Special semi-metallic brake pads. *Shoe type 2 speed transmission.*CNC machined clutch bell with screw-on changeable gears.*CNC machined 7075-T6 aluminium, milled out slim line chassis. *Secure transponder mount.*High flow air filter for maximum engine protection.*Side body mounts and body protector. *Rear air flow diffuser creates more down force.*Exhaust deflector design to protect the inside of the body.*Chrome exhaust pipe detail parts.*High grip radial tires on 17mm hex wheels.*Choice of different body designs.
THIS IS NOT A TOY !ADDITIONAL PARTS NEEDED
INSTRUCTION MANUAL
*Radio System*.21 - .28 Engine* Batteries 8 AA for Radio* Receiver Batteries (10202 Hump Pack)* Model Fuel 20% Nitro* Paint for Lexan Bodies* CA Glue
This kit is extremely fast, and can easily go over 40mph and can seriously injuredsomeone. If you are under 18years of agehave and adult supervision.
BLANK
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser.
and good experience you must observe a few rules. This Precautions
kit is extremely fast, easily over 40MPH, and can seriously • This kit is not a toy. Always run car with a second
injure someone if you are not careful.person as a spotter and pitman.
Where to run car?• Hot Parts - The pipe, manifold, engine and head are very
• Any running area you choose must be dry. Do not run hot and will cause burns.
car near any water or wet dirt.• Do not run on public streets. It is very easy to have the
• Rotating Parts - Keep hands away from the drive train, car run over or damaged by hitting the curb.
wheels, and engine when engine is running.• Do not operate car in tight confined places. The car is
very fast and will easily hit something. • Radio - Check batteries life before running the car. If • Do not run near people or animals.
radio does not have full control of the car with steering
and/or throttle/brake do not run until corrected. Failure to • Due noise, you will want to consider the surrounding
correct this will result in possible injury and damage to the area when operating the car.
car or property.• Do not operate the car at night. You will not be able to
drive it without hitting something.• Glow fuel - Do leave the glow fuel unattended with the lid
• Do not operate the car indoors. Engine exhaust is not off. Fuel contains Methanol and Nitro Methane and is
healthy.flammable and poisonous.
Glow FuelStore fuel in cool ventilated location. Refer the glow fuel • Glow fuel is poisonous!
• Glow fuel is flammable! label for additional precautions.• Do not leave in fuel bottle with lid off at any time.• Do not use any fuel other than glow fuel in this engine. • Car Fuel tank - Never store fuel in car tank, it will ruin the
engine if left in tank.First Time Starting the EngineCaution! When starting engine make sure the following is • Always turn off the car BEFORE turning off radio.observed.• Set engine Master needle to 3 turns (rich setting) • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY • Do not do this alone, get an experienced friend to help at ISSUE.first.• Fill fuel tank, try not to spill fuel. Do not spill fuel on IF YOU DO NOT BREAK-IN ENGINE receiver
CORRECTLY, MAINLY AT LOW RPM, • Hold car off the ground, so it will not runaway when first
starts YOU WILL BREAK THE CONNECTING • Turn on Radio and check the linkage before starting
ROD!engine.• Turn on car receiver battery switch.• Always have an air filter on the carburetor to keep dirt
FAILURE TO NOT READ AND out.
FOLLOW BREAK-IN ENGINE Engine Break-in• See Engine Page.
INSTRUCTIONS WILL VOID Emergency Stopping Engine When Running• Remove air filter and cover carb. intake. WARRANTY!• Squeeze fuel line and hold until engine stops.• With a rag, cover exhaust outlet.
Storing Car After Running• Remove fuel from tank and fuel lines• Turn off radio in car• Put a few drops of after run in engine to keep it from
rusting.
The car is very fast
and will too easily hit someone.
THINGS NEED BESIDES THE KIT
RADIO CONTROL UNIT
12V Battery for Starter Box(must have)
Glow Plug Long Heat with Battery & Charger# 10215....$27.95(please note OFNA Glow Heats available)
AA Batteries ( 12 pcs ) for radio
Note: Carefully read the instruction manual of your 2 channel radio controller before using.
Radio must be set at neutral positionbefore installing in the kit.
SEQUENCE TO SET NEUTRAL
Note: Pro kit does not include engine!
Glow Fuel20%
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral,servo horns must be in neutral as will. *Adjustment can be made by re- installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
Retract the antenna. (Transmitter)
111111
12
13
REQUIRED FOR OPERATION
Bottle’s with spout# 10160 - large 500cc# 10161 - large 500 ccAuto Stop# 10162 - small 250cc# 10164 - CNC spout 500CC# 10167 - CNC spout 800CC
SUITABLE SERVO SIZE
29mm - 42mm
15mm - 21mm
m36mm-41 m
3.5 cc (21 Class) ENGINE
REAR EXHAUST
Off-Road Starter Box, 12V motor# 10250 - 1/8 scale Starter Box# 10253 - 1/8 scale Starter Box w/ Panel
# 92571 - Power Panel Glow Heater# 92572 - Cable for Glow Plug
Off-Road Starter Box, two 550 motors# 10248 - 1/8 scale Starter Box# 10249 - 1/8 scale Starter Box,RTROptional Parts
More Optional Parts . . .
#10202 NiHm Battery Hump Pack .. $34.95
# 10214 NiHm Battery Pack Charger.. $7.95
# 51007 OFNA/Picoo Glow Plug .. $4.95
OFNA/PiccoP-9R EVO#51219
TOOLS NOT INCLUDED IN KIT
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Cutter
Curved Scissors
Knife
Instant Cemment
Cross Wrench
Masking Tape
Paints
Brush
Precision Caliper
INCLUDED WITH KIT
100000 50000
Diff. Oil
Shock Oil
1.5mm Allen Wrench
2mm Allen Wrench
2.5mm Allen Wrench
4mm'5mm Allen Wrench
80WT
PLASTIC PARTS FOR USE
40533FRONT AND REAR GEAR BOX
40717 FRONT AND REAR LOWER ARM
40537REAR UPPER ARM
30800Throttle Linkage Plastic
40538DIFF. CASE
40040CENTER DIFF. MOUNT PLASTIC PARTS
40716FRONT UPPER ARM
40718FRONT KNUCKLE ARM
40721FRONT BUMPER
31304REAR UPPER RIGHT
40643SHOCK PLASTIC
Parts ForNot Use
40720SIDE IMPACT BUMPER AND BODY POST
40735EXHAUST PIPE DETAIL PARTS AND BACK MIRROR
40734REAR WING AND WING MOUNT
40722EXHAUST GAS DEFLECTOR
4071940719ARM HOLDER
40541RECEIVER BOX
40539SERVO SAVER
PLASTIC PARTS FOR USE
SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL
EnsureFreeMovement
Ensure FreeMovement
ApplyGrease
Apply Grease
Oil
Tighten
Tighten
Do NotOver Tighten
RotateDirection
RotateDirection
Contact Adhesive
Contact Adhesive
Screw Cem nte
BAG
1:1
Parts Bag UsedDegrease WithMotor Spray
Do Not Over Tighten
Clockwise Rotation
Anti-clockwiseRotation
True-To-ScaleApply OilApply Screw Cement
Parts forNot Use
ASSEMBLY OF THE SHOCK CAP AND SPRING
ASSEMBLY OF THE SHOCK SHAFT2
UP
Down
Move slowly.
Fill the shocks with oil.
304036mm Ball
2.6x5mmWasher
40635Shock ShaftDust Covers
400602.5mm Nylon Nut
40736Shock Shaft
40638Shock Piston
Step 2
1
3
40643ShockSpring Holder
40738Shock Spring(Red)
2.6x5mmWasher
.....x4400602.5mm Nylon Nut
.....x4304036mm Ball
.....x8
Step 1
ASSEMBLY OF THE FRONT AND REAR SHOCKS1
Make 4 shocks for Front and Rear.
400907mm R-ring
40737Shock Body
400902mm Washer
400901mm Washer
40633 Shock Cap
40640Pressure Top(Orange)
.....x8
.....x4
.....x440090 2mm Washer
40090 1mm Washer
400903.5mm O-Ring
400903.5mm O Ring
400903.5mm O Ring
40634Spring Adjuster
4063615x1mm O-Ring
Fit the o-ringinto groove before assembly.
400907mm R-Ring .....x4
40637Dust Felt
40643Shock PlasticBall End(Short)
Do not over tighten the 2.5 mmnylon nut.
1. Pull down piston, attach pressure top and shock oil overflow with tissue paper.
1. Pull down piston and pour oil into shock cylinder to approx 90%.
2.To remove air bubbles by slowly moving piston up and down.
Step 2 Step 2
BAG
NO.1BAG
NO.1BAG
Step 1
NO.1NO.12
84mm
*Be careful not to damage shock shaft.
Oil
Oil
0 10 20 30 40 50 60 70 80 90
mm
*Total length for 84mm.
RotateDirection
Do NotOver Tighten
Tighten
Step 1 Step 2
ASSEMBLY OF THE FRONT AND REAR DIFF.4
360538X16mmBall Bearing
40514Cap Joint
4X4 mmSet Screw
40538Diff. Case
40009P6 O-Ring
40513Diff. Gear(Large)
4051743TLargeBevel Gear
40009P6O-Ring
40513Diff. Gear
360538x16mm Ball Bearing
940344x4mmSet Screw
400102.5x13.8mm Pin .....x4
.....x4
.....x4
.....x2
40009P6 O-Ring
40514Cap Joint
360538X16mmBall Bearing
400102.5x13.8mm Pin
5
.....x16
307764x10mmWasher
307734mmCross Pin .....x4
ASSEMBLY OF THE FRONT AND REAR DIFF.
if OiD f. l
40011Diff. Gasket
3X12mmFlat HeadHex Screw
307734mmCross Pin
4002413x16x0.2mmShim .....x8
360538x16mm Ball Bearing .....x4
2
6 ASSEMBLY OF THE FRONT AND REAR GEAR CASE
940365x5mmSet Screw
40519Cap Joint
40533Gear Case
4002413X16X0.2mmShim
360538X16mmBall Bearing
4X35mmHex Screw
4002413X16X0.2 mmShim
4051613TSmall Bevel Gear
360538X16mmBall Bearing 4X16mm
Hex Screw
¡Adjust the backlash¡@with the shims.
40533Gear Case
400102.5x13.8mmPin
*Put the Diff. Oil #100000 for front and the #50000 for Rear*Fill the Diff. case to approx. 80% with the Diff. Oil
40513Diff. Gear(Small)
307764X10mmWasher
Step 1 Step 2
NO.2BAG
BAG
Step 1 Step 2
BAG
940203x12mmFlat HeadHex Screw
.....x8
940154x35mmHex Screw
.....x4
940114x16mmHex Screw
.....x4
NO.1NO.12
NO.2NO.4NO.5
Builds two gear case for front and rear.
NB. It is very important to remove the 30776 washer if the gear mesh is too tight.
Tight the diff screws in this order.
1
4
3
2
Sc
wre
Cement
Oil
Oil
TightenBuilds two differentials for front and rear.
Builds two differentials for front and rear.
ApplyGrease
ASSEMBLY OF THE SERVO SAVER
40719Front Upper ArmHolder (Plastic)
8
ASSEMBLY OF THE SERVO SAVER
3
9
.....x5
940413mmNylon Nut
400746x10mmBall Bearing .....x4
400746x10x3mmBall Bearing
400746x10x3mmBall Bearing
40511Servo SaverPost
400746x10x3mmBall Bearing
3x10mmHex Screw
40568GraphiteFront Plate
40694CNC Center Brace (Front)
ASSEMBLY OF THE SERVO SAVER
40563Servo SaverTube(Hard-Coated)
40539Servo SaverHorn
40034Servo SaverSpring TensionAdjuster
40500Servo SaverSpring (Black)
7
400734x8mmFlange Bearing
40037Steering Plat Hex Screw .....x2
.....x2
4002413x16x0.2mmShim .....x2
40539Servo SaverHorn
4002413X16X0.2mmShim
40037Steering Plate Hex Screw
40560Alum. Servo SaverConnecting Plate(Hard-Coated)
40539Servo SaverHorn
400734x8mmFlange Bearing
* Notice the direction of the servo saver connecting plate.
40719Upper ArmAdjuster
.....x2
.....x2
40531Shock BallEnd Post
40531Shock BallEnd Post
3x25mmCap Screw
40731CNC Alum.Front ShockMount
4x12mmFlat HeadHex Screw
.....x5
Step 1
NO.3BAG
Step 2
Step 1
NO.3BAG
Step 2
NO.3BAG
3mmNylon Nut
940033x10mmHex Screw
900183x25mmCap Screw
940264x12mmFlat HeadHex Screw
.....x2
*Tighten the steering plate hex screw all way down and then back it off 1/2 turn.
EnsureFreeMovement
Assembly of the right and left hand side are the same.
*Set the left and right hand side upper arm adjuster in the same direction.
Left Right
Oil
RotateDirection
Screw em tC en
S ecr w C mee nt
Sc er w Cement
r Sc ewem tC en
ASSEMBLY OF THE STEERING TIE-ROD10
Step 1
11
4
Approx. 29.30 mm
1:1
Front
40533Front Plate Bad
e Scr weC ment.....x4
400387mm Ball
367007mm SteeringBall End .....x4
367007mm SteeringBall End
367007mm SteeringBall End
400387mm Ball
400387mm Ball
940213x15mmFlat HeadHex Screw
4x10mmHex Screw
405483mmNylon Nut(Thin Type)
367904x46mmTurnbuckle
.....x2
405483mmNylon Nut(Thin Type)
Step 1
Step 2
.....x2
401263X6mm Flange Washer
401263X6mm Flange Washer
ASSEMBLY OF THE SERVO SAVER AND FRONT UPPER ARMS
.....X2405253x48.1mm Arm Shaft
40719Shock Stay
3x12mmFlat HeadHex Screw
4x12mmFlat HeadHex Screw
40716Caster AngleAdjuster(1mm and 3mm)
40716Caster AngleAdjuster (2mm)40719
Upper ArmAdjuster
Step 240525
Arm Shaft3x48.1mm
40525
Arm Shaft3x48.1mm
29.30 mm
BAG
NO.3BAG
940203x12mmFlat HeadHex Screw
.....x2
940264x12mmFlat HeadHex Screw
.....x4
940094x10mmHex Screw
.....x2
NO.3NO.4
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
*Insert the upper arm adjust into shock stay.
40716Front UpperArm
*Set the left and right hand side upper arm adjuster in the same direction.
Left Right
NO.5
5
12 ASSEMBLY OF THE FRONT SHOCK STAY
3x15mmHex Screw
36742Bushing
359585x8x2.5mmBall Bearing
40719Shock Mount(A)
40719Shock Mount(B)
"L"make are for inside.
ASSEMBLY OF THE FRONT SHOCKS ONTO SHOCK STAY13
940413mmNylon Nut
3x8mmWasher
40643Shock CapWasher .....x2
.....x2
.....x2
40643Shock CapWasher
3x8mmWasher
3mmNylon Nut
3x12mmHex Screw
Step 1
Step 2
ASSEMBLY OF THE REAR UPPER ARMS14
1。G1
368507mmBall 36861
5x35mmTurnbuckle
40537Rear Upper Arm
40719Upper ArmAdjuster
40719Rear Upper ArmHolder (Plastic)
4x16mmHex Screw
.....x2
368507mmBall
40065Upper ArmPlastic Rod End
.....X2
.....X4
359585x8x2.5mmBall Bearing
36742Shock CapBushing
Approx. 12.5 mm
ャ� 12.5 mm
NO.4BAG
BAG
BAG
940053x15mmHex Screw
.....x2
940043x12mmHex Screw
.....x2
940114x16mmHex Screw
.....x2
NO.1
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
*Take the shock cap washer from the shock plastic tree.
EnsureFreeMovement
*Set the left and right hand side upper arm adjuster in the same direction.
Left Right
Do NotOver Thigten
6
15
ASSEMBLY OF THE REAR SHOCK MOUNT16
ASSEMBLY OF THE REAR UPPER ARMS
4X12mmHex Screw
40694CNC Center Brace (Rear)
3x12mmFlat HeadHex Screw
4x12mmFlat HeadHex Screw
40716Caster AngleAdjuster (2mm)
40716Caster AngleAdjuster (1mm)
40546
Arm Shaft3x42.7mm
40719Shock Stay
40546 3x42.7mmArm Shaft .....x2
40531Shock BallEnd Post
40732CNC Alum.Rear ShockStay
.....x2
40531Shock BallEnd Post
3x25mmCap Screw
4x12mmFlat HeadHex Screw
40719Upper ArmAdjuster
40546
Arm Shaft3x42.7mmRear
NO.5BAG
NO.5BAG
940203x12mmFlat HeadHex Screw
.....x2
940264x12mmFlat HeadHex Screw
.....x4
940104x12mmHex Screw
.....x1
900183x25mmCap Screw
.....x2
940264x12mmFlat HeadHex Screw
.....x2
Step 1 Step 2
.....x2
.....x4
359585x8x2.5mmBall Bearing
ASSEMBLY OF THE REAR SHOCK STAY 17
36742Shock CapBushing
3x15mmHex Screw 40719
Shock Mount(A)
40719Shock Mount(B)
359585x8x2.5mmBall Bearing
Notice "L"make are for the inside.
36742Shock CapBushing
NO.5BAG
940113x16mmHex Screw
.....x2
*Set the left and right hand side upper arm adjuster in the same direction.
Left Right
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
*Insert the caster angle adjuster onto arm shaft.
EnsureFreeMovement
crewS
mnt
Cee
wScre C
entem
Screw Cement
Do NotOver Tighten
7
ASSEMBLY OF THE REAR SHOCK ONTO SHOCK STAY 18
40643Shock CapWasher
40643Shock CapWasher
3mmNylon Nut
3x8mmWasher
3x12mmHex Screw
Step 1
Step 2
ASSEMBLY OF THE TWO SPEED GEARS 19
Step 3352251st Spur GearHolder(One-Way)
352481st Spur Gear(48T)
35228Alum. Nut
352308x12mmFlangeBall Bearing
401122-Speed Shaft
35235Clutch shoe Carrier
5x5mmSet Screw
.....x2
.....x194036M5x5mmSet Screw
352308x12mmFlange Ball Bearing
35219Alum. Nut
Clockwise
352442nd Spur Gear(44T)
352342nd Spur GearClutch Bell
*Put the clutch shoe carrier to the edge of the groove on the shaft.
NO.1BAG
940413mmNylon Nut
3x8mmWasher
.....x2
.....x2
.....x2
Anti-Clockwise
NO.7BAG
940043x12mmHex Screw
.....x2
Step 1 Step 2
20
35236ClutchShoe
352374mm Ball
ASSEMBLY OF THE TWO SPEED TRANSMISSION
360538x16x5mmBall Bearing
940365X5mmSet Screw .....x2
5X5mmSet Screw
360538x16x5mmBall Bearing
352376X6mmSet Screw
352374mm Ball
352376X6mmSet Screw
.....x2
.....x2
940413mmNylon Nut
3mmNylon Nut
5X4mmSet Screw3mm
Nylon Nut
40120BrakeCap Joint
40120BrakeCap Joint
1st Gear Assembly
2nd Gear Assembly
.....x2
352374mm Ball
35237Spring
35237Spring
352376X6mmSet Screw
NO.7BAG
3x15mmHex Screw
35236ClutchShoe
3x15mmHex Screw
940053x16mmHex Screw .....x2
cw
Sre
Ceent
m
S r w c e
Cement
S
crew
Cem
ent
Assembly of the right and left hand side are the same.
* Push the flange ballbearing into clutch bell.
*Screw the 3x15mm screw into the bottom and back off 5 turns.
3x15mmScrew
3x15mmScrew
* Place the set screw in the "D" cut.
Do NotOver Tighten *Take the shock cap washer
from shock plastic tree.
RotateDirection
RotateDirection
EnsureFreeMovement
EnsureFreeMovement
*Leave a 1.5 mm space between the two brake pads.
21 ASSEMBLY OF THE TWO SPEED TRANSMISSION INTO THE CENTER MOUNT
.....x1
302125x8mmFlange Bearing
302125x8mmFlange Bearing
3x10mmHex Screw
40719Center Diff.Mount Plate
40547Brake Cam
40040Center Diff.Mount
40040Center Diff.Mount
40512Center Diff.Mount Post
ASSEMBLY OF THE BRAKE AND CENTER DIFF. MOUNT22
.....x1940333x3mmSet Screw
40714Center CarryHandle
4x4mmSet Screw
49009CNC Brake Disk
3x15mmHex Screw
36659Brake Pad
30171Brake Lever
3x3mmSet Screw
36659Brake Pad
.....x2940344x4mmSet Screw
8
Step 1 Step 2
NO.7BAG
NO.7BAG
940033x10mmHex Screw
.....x4
940113x16mmHex Screw
.....x2
3x10mmHex Screw
23 ASSEMBLY OF THE ARM HOLDER ONTO CHASSIS
40719Arm Holder(Front/Front)
40719Arm HolderAdjuster
4x16mmFlat HeadHex Screw
40719Arm HolderAdjuster
4x16mmFlat HeadHex Screw
40719Arm Holder(Front/Rear)
40719Arm Holder(Rear/Front)
40719Arm Holder(Rear/Rear)
BAG
940274x16mmFlat HeadHex Screw
.....x8
NO.4NO.5
1.5mm
*Insert the brake disc into brake cap joint before assembly.
*set the arm holder adjuster to the same direction.
*set the arm holder adjuster to the same direction.
A A
A A
crewS
C meent
Do NotOver Tighten
(Type A)
(Type A)
40729Chassis
9
Step 1
Step 2
ASSEMBLY OF THE REAR LOWER ARMS 25
40711 4mm Arm Shaft
4x10mmSet Screw
3x18mmHex Screw
3x8mmSet Screw
.....x2368704x10mmSet Screw
.....x4940063x18mmHex Screw
.....x2940353x8mmSet Screw
40717Rear Lower Arm
40719Stabilizer mount
31308Stabilizer
40719Stabilizer BalanceAdjuster
4x10mmSet Screw
3x18mmHex Screw
40719Stabilizer BalanceAdjuster
3x8mmSet Screw
Step 1
Step 2
26 ASSEMBLY OF THE FRONT AND REAR GEAR BOX ONTO THE CHASSIS
940274x16mmFlat HeadHex Screw
.....x8
.....x2
940264x10mmFlat HeadHex Screw
4x10mmFlat HeadHex Screw
4x16mmFlat HeadHex Screw
3x12mmHex Screw
3mmNylon Nut
.....x4
940413mmNylon Nut
3x12mmHex Screw
4x16mmFlat HeadHex Screw
Front Gear Box Assembly
Rear Gear Box Assembly
.....x4
940203x12mmFlat HeadHex Screw
3mmNylon Nut
40717Rear Lower Arm
31308Stabilizer
40719Stabilizer mount
940053x15mmHex Screw
.....x2
NO.6BAG
BAG NO.5NO.3
NO.6
Step 1
Step 2
ASSEMBLY OF THE FRONT LOWER ARMS 24
40711 4mm Arm Shaft
40711 4mm Arm Shaft
4x10mmSet Screw
3x18mmHex Screw
3x8mmSet Screw
.....x2368704x10mmSet Screw
.....x4940063x18mmHex Screw
.....x2940353x8mmSet Screw
40717Front Lower Arm
40719Stabilizer mount
31308Stabilizer
40719Stabilizer BalanceAdjuster
940053x16mmHex Screw
.....x2
NO.6BAG
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
2mm
2mm
*A 3x8mm set screw is use for thighten or loose stabilizer.
(Left Side)
Center
Center
*Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.
*Keep stabilizer ball in the center. Turn stabilizer adjuster to adjust the stabilizer to the same angle.
Adjuster
Adjuster
Step 1
28 ASSEMBLY OF THE FRONT KNUCKLE AND FRONT SUSPENSION ARMS
10
360538x16mm Ball Bearing
..........X4
360552.5x16.8mm Pin
..........X2
940344X4mmSet Screw ..........X2
40724Dust Boot Bushing
40724Dust Boot Bushing
3x16mmFlat HeadHex Screw
401263X6mm Flange Washer
40526AlumWheel Hub
360552.5x16.8mmPin
5x4mmSet Screw
cw
S
reem
et
Cn
40521Universal Joint(Front)
360538x16mm Ball Bearing
360538x16mm Ball Bearing
3mmNylon Nut
Step 1Step 2
27
40718Ball typeKnuckle Arm(left)
ASSEMBLY OF THE FRONT KNUCKLE ARMS
3690314mmSteering Ball
.....x8
940492x8mmCap Screw
2x8mmCap Screw
40718Dost Boot CoverHolder
40723Dust Boot Cover
3690414mmAlum. Nut .....x4
3690312mmSteering Ball .....x4
3690314mmSteering Ball
40718Plastic Washer
40723Dust Boot Cover
Step 2
940213x16mmFlat HeadHex Screw ..........X2
3690412mmAlum. Nut
40718Plastic Washer
3690412mmAlum. Nut
40718Dost Boot CoverHolder
..........X2
940413mmNylon Nut
Step 1
ASSEMBLY OF THE REAR WHEEL HUB 29
3130711mmSteering Ball
.....x2
3130612mmAlum. Nut
4x4mmSet Screw
3130711mmSteering Ball
31304Rear UpperRight
40733Universal Joint(Rear)
360552.5x16.8mm Pin
.....x2
360538x16mm Ball Bearing
.....x4
360538x16mm Ball Bearing
360552.5x16.8mmPin
40526Alum.Wheel Hub
31305Washer
360538x16mm Ball Bearing
8x12x1mm Washer
940344X4mmSet Screw .....x2
3130711mmSteering Ball
31305Washer
3130612mmAlum. Nut
NO.6BAG
BAG
BAG Step 2
NO.3NO.6NO.12
NO.6NO.12
*Notice the direction of the plastic washer.
EnsureFreeMovement
EnsureFreeMovement
EnsureFreeMovement
*Put the drive shaft into cap joint before assembly.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
L
Do NotOver Tighten
cew
Sr
Cee
ntm
Do NotOver Tighten
11
Step 1
31 ASSEMBLY OF THE FRONT PUSH RODS
30 ASSEMBLY OF THE REAR SUSPENSION ARMS
Step 2
.....x2
940413mmNylon Nut
.....x2940083x25mmHex Screw
304036mmBall
304036mm Ball
407123.5x48mm Turnbuckle
3x20mmHex Screw
30401Plastic Ball End
3x25mmHex Screw
3mmNylon Nut
3x12mmHex Screw
.....x2304036mm Ball
.....x2940073x20mmHex Screw
940043x12mmHex Screw
.....x4
Step 1
32 ASSEMBLY OF THE REAR PUSH RODS
Step 1
Step 2
3x20mmHex Screw
304036mmBall
304036mm Ball
407123.5x48mm Turnbuckle
30401Plastic Ball End
.....x2304036mm Ball
.....x2940073x20mmHex Screw
940043x12mmHex Screw
.....x4
30401Plastic Ball End
30401Plastic Ball End
NO.6BAG
NO.6BAG
Approx. 35mm
1:1
35mm
NO.6BAG
Approx. 34mm
1:1
34mm
3x12mmHex Screw
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
Assembly of the right and left hand side are the same.
*Insert the drive shaft before assembly.
12
Step 1
34 ASSEMBLY OF THE CLUTCH
33 ASSEMBLY OF THE TWO SPEED TRANSMISSION ONTO THE CHASSIS
10098SG Clutch Nut
405733 Pin Flywheel(35mm)
Engine rotation direction.
*Fit the flywheel using a pair of the plier and cross wrench.
10101Clutch Spring
Step 2
405733 Pin Flywheel(35mm)
10091Pilot Shaft(Not Included)
Threaded Crank Shaft
* Only use the 10091 pilot shaft for threaded crank shaft engine.
10330Tapper Corn
SG TypeCrank Shaft Engine
10010 Clutch Shoes
*Place the clutch shoes with the clutch springs over the 3 pins of the flywheel.*Using a phillips screw driver or needle nose pliers and bend the small end lf the clutch spring behind the pilot shaft #174D or #180D than press down.
940264x10mmFlat HeadHex Screw
.....x4
*Insert drive shaft into cap joint before assembly two speed onto chassis.
4x10mmFlat HeadHex Screw
40710Center DriveShaft
40710Center DriveShaft
103307mmlTapper Corn
Step 1
Step 2
Step 3
ASSEMBLY OF THE CLUTCH35
.....x1
.....x1
.....x1
.....x3100995x8x0.3mmWasher
341105x10x4mmBall Bearing
100993x7mmWasher
100993x5mmCap Screw
100995x8x0.3mmWasher
100993x7mmWasher
100993x5mmCap Screw
359585x8mmBall Bearing
359585x8mmBall Bearing
341105x10x4mmBall Bearing
3524016T-1stClutch Gear
35242Clutch Bell
3525520T-2ndClutch Gear
.....x1
NO.7BAG
NO.10BAG
NO.10BAG
*Adjust the backlash with the washer.
Screwen
Cem
t
Sc ew r
Cement
cSrew
ent
Cme
Sc ew r
Cement
Sew
cr
Cem
ent
cSrew
Cement
Tighten
13
Step 1 Step 2
36 ASSEMBLY OF THE MANIFOLD AND MUFFLER
40574Low ProfileEngine Mount
3x12mmCap Screw
.....x4
940383x12mmCap Screw
Muffler(Option)
Manifold(Option)
975011/8 Spring
975011/8 SiliconeSeal(Option)
*The muffler and manifold may not be included in some kit.
37 ASSEMBLY OF THE ENGINE ONTO THE CHASSIS
101145mmEngine MountScrew .....x4
5x5mmSet Screw
975011/8 SiliconeSeal(Option)
10120ManifoldSpring
4x10mmFlat HeadHex Screw
40050Muffler StayPost
10052Muffler Stay
4x4mmSet Screw
10114Engine MountScrew 5mm
*Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine.*If the space is not correct the spur gear will be damaged.
38 ASSEMBLY OF THE MANIFOLD ONTO THE ENGINE
.....x1
.....x1
940394x10mmFlat HeadHex Screw
940365x5mmSet Screw
940344x4mmSet Screw
.....x1
NO.10BAG
NO.10BAG
BAG NO.11NO.10
NotIncluded
NotIncluded
NotIncluded
NotIncluded
NotIncluded
S r wc e mCe ent
Screw Cement
rSc ew mCe ent
Supplied with pipe (Not Included)
Note book Paper.
Screw Cement
Step 1
ASSEMBLY OF THE FUEL TANK ONTO THE CHASSIS39
Step 1 Step 2
41 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX
14
40
3x10mmFlat Head HexScrew
940033x10mmHex Screw
.....x2
.....x2
940193x10mmFlat HeadHex Screw
3x10mmHex Screw
40543Fuel Tank
40539Fuel TankPost
Pressure Nipple
940023X8mmHex Screw
*Use the screw provided with your switch
*Connect the switch wire to receiver.
40541Switch holder
2X8mmScrew .....X4
2X8mmScrew
10280Switch Cover
Switch
40541Receiver Box
40541Receiver Box
Step 2
40642Antenna PipeFixing Nut
40541Receiver BoxCover
37410Clips
40541Receiver BoxCover
*Put the servo wire into receiver box and connect to receiver.
30560Antenna Pipe
Antenna
3X8mmHex Screw
940023X8mmHex Screw
.....X2
Battery
Receiver
*Use the original battery case or rechargeable hump pack battery.
*Connect battery wire to switch.
Put the protector rubberonto your servo.
Step 1 Step 3
ASSEMBLY OF THE RADIO TRAY40
.....X7
Step 2
40541Radio Tray Post( Plastic )
3x8mmHex Screw
3x8mmHex Screw
3x8mmHex Screw
34026Servo Washer
34026Servo Mount
3x16mmHex Screw
.....X8940403x8mmWasher
40715Alum. Throttle Pivot Post
3x8mmWasher
3x8mmWasher
.....X8940053x16mmHex Screw
BAG
NO.9BAG
Steering Servo
Throttle Servo
40580Protective Foamfor Receiver Box
40580Protective Foamfor Receiver Box
NO.9BAG
NO.3NO.11
34026Servo Washer
34026Servo Mount
3x16mmHex Screw
Servo Wire
S
crew
Cem
ten
Do NotOver Tighten
Do NotOver Tighten
40730Graphite Radio Tray
ASSEMBLY OF THE THROTTLE LINKAGE INTO SERVO
ASSEMBLY OF THE STEERING ROD AND RADIO TRAY ONTO THE CHASSIS
Step 1
Step 2
ASSEMBLY OF THE THROTTLE LINKAGE
42
Step 1 Step 2
44
43
15
940033x10mmHex Screw
.....x1
10765Servo HornAdapter
*Use the screw provided with your servo.
.....x2304036mm Ball End
10765Servo Horn
.....x3940333x3mmSet Screw
.....x1
940502.6x10mmCap Screw
.....x1
.....x2
.....x1940043X12mmHex Screw
30401Plastic Ball End
304036mm Ball End
308002.6x6mmWasher
.....x3
10765Servo HornAdapter
10765Servo Horn
3X12mmHex Screw
304036mmBall
304036mmBall
*Use the screw provided with your servo.
.....x8
940193x10mmFlat HeadHex Screw
3x10mmFlat HeadHex Screw
3x10mmFlat HeadHex Screw
3X12mmHex Screw
30800ThrottleBall End
301722X68mmBrake Rod
10300AlumStopper
3x3mmSet Screw
2.6x10mmCap Screw
30531ThrottleSpring
30800Adjust Mount
3x3mmSet Screw
3x10mmHex Screw
3x8mmWasher
40719Servo Horn
308002mmAdjust nut
376504mmBall End(Short)
2.6x6mmWasher
3x5mmHex Screw
3x3mmSet Screw
30800Adjust Mount
Parallel
373604mmBall & Socket
30401Plastic Ball End
10300AlumStopper
373604mm Ball & Socket
NO.9BAG
359585x8x2.5mmBall Bearing
NO.9BAG
NO.9BAG
Approx. 49 mm
1:1
¬ù 49mm
407133x64mmTurnbuckle
.....x1940353x8mmSet Screw
3x8mmSet Screw
376504mmBall End(Long)
3x3mmSet Screw
10300AlumStopper
*Snap on.
Tighten
Tighten
*Ensure that servo gears are centered before attaching the servo horns. The best way to accomplish this is by connecting the servos to the radio system and setting the trim to the center.
EnsureFreeMovement
* Choose the right servo horn adapter for your servo.
S J F H
Sanwa/Airtronics JR Futaba HiTech
Cut off the servo saver as shown.
A
A'
Completely Finished
16
ASSEMBLY OF THE SIDE IMPACT BUMPER & POST
47 ASSEMBLY OF THE FRONT BUMPER
46
40722Exhaust GasDeflector
40722Exhaust Gas Deflector
40721Front BumperPost
40721Front BumperPost
40721Front Bumper
2X12mmScrew .....x4
940424mmNylon Nut
940264x12mmFlat HeadHex Screw
.....x3
.....x2
940203x12mmFlat HeadHex Screw
ASSEMBLY OF THE SIDE BODY POST4540720Side Body Support
.....x8
940203x12mmFlat HeadHex Screw
3x12mmFlat HeadHex Screw
3x12mmFlat HeadHex Screw
3x10mmFlat HeadHex Screw
2X12mmScrew
2X12mmScrew
40720Side Impact BumperBody Post
40720Side Impact BumperBody Post
40720Side Impact BumperBody Post
40720Side Impact BumperBody Post
40720Side Impact BumperBody Post
2x12mmScrew
.....x2
940193x10mmFlat HeadHex Screw
4x12mmFlat HeadHex Screw
3x12mmFlat HeadHex Screw
4mmNylon Nut
NO.8BAG
NO.8BAG
NO.8BAG
.....x3
Assembly of the right and left hand side are the same.
Tighten
Tighten
Do NotOver Tighten
Do NotOver Tighten
*Push onto side body post.
R
F
Step 1 Step 2
ASSEMBLY OF THE FRONT BUMPER48
Step 1
Step 2
50
49
17
ASSEMBLY OF THE FRONT AND REAR BUMPER
ASSEMBLY OF THE REAR BUMPER
Approx. 3mm
40721Front BumperTop Plate
40117Body Post
40721Rear Bumper Post
40721Rear Bumper
.....x2
368704x10mmSet Screw
940094x10mmHex Screw .....x2
.....x2
4mmNylon Nut
940264x12mmFlat HeadHex Screw .....x2
940264x12mmFlat HeadHex Screw .....x2
.....x4
940203x12mmFlat HeadHex Screw
4x12mmFlat HeadHex Screw
.....x2
368704x10mmSet Screw
4x10mmSet Screw
4x10mmSet Screw
4x12mmFlat HeadHex Screw
40117Body Post
31159Body Clip
40720Body Post
4x10mmHex Screw
4x12mmHex Screw
40725Foam Bumper
31159Body Clip
40117Body Post
40712Body Post
31159Body Clip
40117Body Post
2.6X15mmScrew
2.6X15mmScrew
2X8mmScrew
.....x4
940264x12mmFlat HeadHex Screw .....x2
940424mmNylon Nut
40721Rear BumperTop Plate
NO.8BAG
NO.8BAG
NO.8BAG
Approx. 4 mm
ャ� 4mm
3x12mmFlat HeadHex Screw
3x12mmFlat HeadHex Screw
* The 4x10mm set screw is used to adjust down stop.
* The 4x10mm set screw is used to adjust down stop.
Completely Finished
Tighten
Tighten
Tighten
Tighten
Tighten
Tighten
Step 1 Step 2
ASSEMBLY OF THE REAR EXHAUST PIPE DETAILS51
53 ASSEMBLY OF THE TIRES AND WHEELS
52 ASSEMBLY OF THE AIR FILTER
18
38400Air Filter
86023Wheel
40735Muffler
86059Inner Sponge(WidE)
86052Tire
940023x8mmHex Screw
.....x2
940104x12mmHex Screw
.....x2
.....x1940403x8mmWasher
3x8mmHex Screw
3x8mmWasher
4x10mmHex Screw
3x12mmHex Screw
Nylon Strap
86059Inner Sponge(Narrow)
*Notice the direction and make two lift and right hand side tires are the same.*Check the rotation direction before gluing.
40735Muffler Mount
NO.11BAG
940043x12mmHex Screw
.....x2
*Notice the direction of the tires.
*Notice the direction of the tires.
NSTT
IAN GL E
U
Tighten
Tighten
(Right Hand Side)
(Left Hand Side)
10179Fuel Tube
Connect to pressure nipple.
Connect to fuel tank pressure nipple.
Connect to carburetor.
Connect tofuel tank.
Contact Adhesive
Contact Adhesive
Contact Adhesive
Contact Adhesive
*Notice the direction of the tires. Make two the same for the left and 2 for the right. Check the rotation direction before gluing.
*Pull back the tire bead slightly and spot glue in four spots as shown. When dry, glue the rest of the wheel between the spots. Repeat the procedure on the other side of the wheel until fully glued.
*Apply filter oil to the foam before use.
Step 1
ASSEMBLY OF THE WHEELS ONTO THE FRONT KNUCKLE AND REAR HUB54
Step 3
Step 1Step 2
ASSEMBLY OF THE BODY AND PAINTING
19
55
Step 5
Step 4
Spray Paint
Cut out the body as shown.
Completely Finished.
Wash body with warm soapy water to remove any dirt and oil.
Mask the windows from the inside with masking tape.
Before cutting and making holes in the body, put the unpainted bodyon the chassis to confirm the mounting position and location for holes. Use body reamer or drill to make two 8mm holes in the front and two 8mm holes in the rear.
Step 6Paint the body with polycarbonate spray paints.
10803 BLACK10804 BLUE10805 PURPLEBody Reamer (Not included.)
.....x440526Wheel Nut
Tire and Wheelassembly.
40526Wheel Nut
40526Wheel Nut
NO.6BAG
Cut Out
*Make two 8mm holes for the side body posts.
*Make a hole for exhaust gas deflector.
Assembly of the right and left hand side are the same.
*Notice the direction of the tire pattern.
*Notice the direction of the tire pattern.
ォBィ�、ホォ�オ�テ�イユクヒ
57
58
20
40735Wiper
ASSEMBLY OF THE REAR VIEW MIRRORS AND WIPERS
2x6mmCap Screw
40735Wiper holder
P5O-Ring
40735Rear View Mirror Mount
40735Rear View Mirror Mount
40735Rear View Mirror
40735Rear View Mirror
56
.....x12
940193x10mmFlat HeadHex Screw
940023X8mmHex Screw .....x10
3X8mmHex Screw
3x10mmFlat HeadHex Screw
3x10mmFlat HeadHex Screw
40734Wing Mount Holder
40734Wing Mount Holder
3X8mmHex Screw
3X8mmHex Screw
40734Wing Mount
40734Wing Mount
40734Wing
MOUNTING BODY31159Body Clip
31159Body Clip
31159Body Clip
31159Body Clip
31159Body Clip
940472X6mmCap Screw .....x1
NO.8BAG
*Put the body clips from inside the body.
ASSEMBLY OF THE REAR WING
Make two 5mm holes in each side for rear wing mount.
3X8mmHex Screw
Do NotOver Tighten
Do NotOver Tighten
Do NotOver Thigten
21
59 STARTING OF THE ENGINE
1. Turn on transmitter and then receiver.2. Fill fuel tank with fuel bottle.3. Connect 1.2V glow plug .4. Start engine with a 12V starter. ( Notice the direction of the starter.)5. After the engine has started, remove the 1.2V glow plug .
igniter
igniter
* Follow the engine manufacturer instruction manuals regarding engine set-up, carburetor and maintenance.
How to start the engine: A 12V Starter Box( Not Included)
1.2V Glow Plug Igniter andCharger (Not Included)
Glow Plug (Not Included)
*There are 2 types of glow plugs available"NORMAL" or "Turbo" depending on the type of the engine.
Normal Plug
Turbo Plug
*To start the car, attach a glow plug igniter to the glow plug, and use either a 12V electric starter or starter box applied to the flywheel exposed through the chassis.
Starter Box(Not Included)
1.2V
1.2V
*Applied to the flywheel exposed through the chassis.
SHIFT UP TIMING ADJUSTMENT Adjust the engine before adjusting the clutch shift timing.Adjust the engine as per engine instruction manual. 1. Once the engine adjustments have been completed, proceed to the
adjustment of the clutch shoe shift timing. (Using a 2mm allen wrench to adjust the clutch shoe on either side.) Note: Clockwise--------Shift timing will become later. Counterclockwise---Shift timing will become quicker.
2. Adjust the clutch shift timing for your track conditions. As you tighten (Clockwise) the 3x15mm screw, the shift timing will become slower. As you loosen (Counterclockwise ) the 3x15mm screw, the shift timing will become quicker.
3. Set the shift timing to the track conditions while the car is running.
3x15mm Hex Screw
3x15mm Hex Screw
6x6mmSet Screw
2mmAllen Wrench
Clockwise(Tighten)
Anti-clockwise(Loosen)
ADJUSTING THE SHIFT POINT
2 SPEED GEAR RATION COMBINATIONS
2 speed transmission allows the car to have more punch out of the corners and higher top speed. We offer many different pinion and spur gear combinations which can be used for different tracks.
Spur Gear Clutch Gear (4 tooth different)
49T/45T
48T/44T
15T-19T 16T-20T 17T-21TTorque
Speed
10215 - Glow Heater, Extra LongW/Charger.
10250 - Starter Box 1/8 scale On/Off-Road.
51007
51006
FRONT TOE-IN AND TOE-OUT SETTING
TOE-IN
TOE-OUT TOE-OUT
NEUTRAL POSITION
Firm rear suspension, over steering.Soft rear suspension, under steering.
Steering Rod
FRONT AND REAR SHOCK ANGLE SETTING
Firm front suspension, less steering.Soft front suspension, more steering.
SETTING GUIDE
FRONT AND REAR CAMBER ANGLE SETTING
- -- -+ ++ +
Turnbuckle Turnbuckle
・ソ、マ、�チウア� ・ソ、マ、�チウア�
NegativeNegative PositivePositive
12 Soft
Soft
Firm12
Soft Firm
Soft
Firm
12
Firm
1234
Rear Toe-In
Rear Toe-In
2.5mm Allen Wrench
Adjust the length of the front steering rod to change the toe angle.
Making the steering rod longer will make the front tires become toe-in.Response will be slower and will over steer. Making the steering rod shorter will make the front tires become toe-out.Response will be quicker and will under steer.We recommended adjusting the front toe-out to 1.5 degrees.
Adjust the length of the rear hub (12mm ball/rear) to change the toe angle.
Making the 12mm ball longer will make the rear tires toe-in.Response will be under steer.
Making the 12mm ball shorter will make the rear tires toe-out.Response will be over steer. We recommended adjusting the rear toe-in is 2 degrees.
Use a 2.5mm allen wrench to adjust toe-in for front and rear.
(Front)
(Rear)
Note: Place the model car on a flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angles to the ground.
The front camber adjustment can be made by moving the 14mmsteering ball at the front upper arms on knuckles, clockwise or anti-clockwise.We suggest using 1.5 degress of negative camber for the front.
(FRONT)
(FRONT)
(REAR)
(REAR)
Adjust the length of the turnbuckle on can be change the rear camber. We suggest using 2 degress of negative camber for the rear.
the rear upper arms
¡Use 2.5mm hex wrench ¡@to adjust upper arm ball¡@in front.
BLANK
OFNA Description RETAIL OFNA Description RETAIL30171 Brake Lever 1.95 40519 Cap Joint 9.9530172 Brake Rod 1.50 40521 Universal Joint, Front 44.9530401 6mm Ball End (Plastic) 2.95 40525 Rear Lower Arm Shaft (3x48.1mm) 6.9530403 6mm Ball & Socket 4.95 40526 17mm Wheel Hub 11.9534110 Ball Bearing 5X10X4 6.95 40550 17mm Wheel Nut 4.9530531 Throttle Spring 2.95 40531 Shock Ball End Post/one- piece/Top 9.9530560 Antenna Pipe 2.95 40533 Gear Case 11.9530776 4x10x0.2 Washer 1.95 40537 Front Upper Arms 6.9530800 2mm Brake Adjust Nut 6.95 40538 Diff. Case (F&R) 9.9530800 Throttle Linkage Plastic 6.95 40539 Servo Saver & Center Bracer 11.9530773 4mm Cross Pin 3.95 40541 Receiver Box 14.9540117 1/8 Truck Body Mount 10.95 40543 Fuel Tank 16.9586052 1/8 Radial Tire 19.95 40546 Front Arm Shaft 3x42.7mm 11.9534026 Servo Fixing (Lay down) 7.95 40547 Brake Cam 8.9540710 Center Drive Shaft 120mm 19.95 40548 M3 Nylon Nut (Thin Type) 1.9540711 4x90mm Arm Shaft 7.95 40568 Graphite Front Plate 31.9540712 3.5x48mm Turnbuckle 9.95 40573 3-pin Flywheel, 35mm 19.9540713 3x64mm Turnbuckle 9.95 40574 Engine Mount (Lowere Type) 18.9540714 Center Handle Bar 3.95 40580 Protect Foam for Receiver Box 1.9540715 Throttle Connecting Alum. Post 7.95 40643 Plastic Shock Parts Set 9.9540716 Rear Upper Arms 9.95 40694 CNC 7075 Chassis Brace, F&R 59.9540717 Front & Rear Lower Arms 19.95 30401 Plastic Parts Set for Damper 2.9540718 Ball Type Knuckle Arms (L&R) 19.95 31159 Body Clips 4.9540719 Arm Holder Plastic 15.95 10120 Manifold Spring 4.9540720 Body Side Bumper 9.95 10280 Switch Cover, red 3.9540721 Front & Rear Bumper 19.95 10300 Alum. Stopper 4.9540722 Exhaust Connecter 7.95 10179 Fuel Tube (45cm) 1.9540723 Dust Proofe Cover 7.95 10270 Fuel Tube Clips 3.9540724 Rubber Bushing for Hex Screw 4.95 10010 3 Shoe Clutch carbon 13.9540725 Foam Bumper 14.95 10101 Clutch Spring 4.9540726 M.Benz CLK DTM Body, clear 79.95 10098 Pilot Shaft, SG Type 4.9540727 Nissan G35 Body, clear 79.95 10114 Engine Mount Screw, 5mm Hex 7.9540728 Porsche Carrera GT Body, clear 79.95 35958 5x8x2.5 Ball Bearing 3.9540729 CNC 7075 Chassis 179.95 10330 Cone, 7mm Brass Tapper 2.9540730 Graphite Radio Tray 39.95 36053 8x16 Ball Bearing 12.9540731 CNC Alum Shock Stay, F 39.95 36055 2.5x17 Pins 3.9540732 CNC Alum Shock Stay R 39.95 30212 5x8x2.5 Frange Bearing 5.9540733 Universal Joint, Rear 59.95 35225 1st Spur Gear Holder (one-way) 26.9540734 Wing & Wing Stay Unit 12.95 35228 Alum. Nut (anti-clockwise) 2.9540735 Real Muffler & Back Mirror 14.95 35230 8 x 12 Flange Bearing 12.9537360 4mm Ball & Socket 4.95 35248 48T 1st Spur Gear 7.9537410 Body Pin (S) 3.95 35244 44T 2nd Spur Gear 7.9537650 4mm Plastic Ball Joint 6.95 35240 Clutch Gear (1st) 16T 11.9540126 3x6x2.5 Flange Washer 3.95 35255 Clutch Gear (2nd) 20T 11.9536700 Steering 7mm Ball 6.95 35242 Clutch Bell 24.9536742 Servo Saver Bushing 1.95 86059 GTP Inner Sponge (L&S) 9.9536790 4x46 Turnbuckle 10.95 31308 Stablizer (Steel) (L&R) 10.9536850 7mm Ball 3.95 31304 Rear Hub (Ball Type) 10.9536861 5x35 Turnbuckle 6.95 31305 Plastic Washer for Ball 8.9536903 Steering Ball 14mm 7.95 31306 12mm Alum. Hex Screw 8.9536904 14mm Alum. Nut 9.95 31307 11mm Ball & Screw 8.9540009 P-6 O-Ring 2.95 35234 2nd Spur Gear Clutch Bell 24.9540010 2.5x13.8 pin 2.95 35219 Alum. Nut (clockwise) 2.9540011 Diff. Gaskets 3.95 35236 Clutch Shoe 14.9540024 Diff Bevel Gear Shim 13x16x0.2mm 2.95 35237 Spring 9.9540500 Servo Saver Spring (Black) 3.95 35237 4mm Ball 9.9540034 Alum. Servo Saver Ring Adjuster 5.95 35235 Clutcn Shoe Carrier 5.9540037 Steering Plate Hex Screws 5.95 35237 6x6mm Set Screw 9.9540038 7mm Balls (Black) 9.95 10765 Universal Servo Horn 8.9540040 Center Diff Mount (plastic) 4.95 40090 Shock Repair Kit 7.9540060 M2.5 Nylon Nut 4.95 86023 1/8 Mesh Wheels (Black) 19.9540050 Muffler Stay Post 6.95 38400 1/10 Air Filter 9.9540065 Rear Upper Ball End 4.95 36659 SPL Brake Pad for 1/8 Cars 31.9540073 Bearing, 4x8 Flange 12.95 40642 Antenna Pipe Fixing Nut 2.9540074 6x10 Ball Bearing 17.95 40633 Shock Cap, 13mm 18.9549009 SPL CNC Brake Disk 19.95 40634 Shock Spring Adjuster 9.9540112 2-Speed Shaft 9.95 40635 Shock Shaft Dust Covers 5.9540120 8mm Cap Joint for Brake 11.95 40636 15x1 O-Ring 3.9540560 Servo Saver Connecting Plate 12.50 40637 Dust Felt for Shock Absorber 1.9540563 Alum. Servo Saver Tube 9.95 40638 Shock Piston, 13mm 7.9540511 Servo Saver Post 6.95 40640 Shock Pressure Top, Orange 5.9540512 Center Diff. Mount Post 13.95 10052 Spring Muffler Stay 4.9540513 Diff. Gear (small & large ) 16.95 40736 DM-1 Shock Shaft 7.95
DM1-PRO PARTS LIST
top related