(part ii) (pdf format)
Post on 09-Feb-2022
6 Views
Preview:
TRANSCRIPT
Page 54
Appendix 5 Guidelines to create Building Information Modelling (BIM) models for AAP, P1, SOM & SPC Preparation for Architectural Assessment Panel(AAP) Submission (Same details requirements on Revit models for P1, SOM & SPC Submission) 1. Procedures for site model creation 1.1 Start new project with standard template Fig.1.1 1.1.1 Set the level of the project
Set the base level of the site Set other levels for main structures (e.g. two domestic block sit on different
levels) 1.2 Import base plan (site layout/setting plan) as reference
1.2.1 Set Origin as the project co-ordinate (in AutoCAD)
Fig.1.2.1
Page 55
1.2.2 Clean-up the CAD file (dwg) before import to Revit
Delete all areafill (i.e. solid pattern, hatching etc.) Delete unnecessary annotation and geometry Purge the CAD file If you found that some blocks were not in the original position after import in
Revit, explored those blocks before import. 1.2.3 Import CAD file (dwg) as base plan Fig. 1.2.3 1.2.4 Setting for plan location
Fig. 1.2.4
Page 56
1.2.5 CAUTION: If the site is far away from the Origin or the site coverage is large, the following warning would be encountered.
Fig. 1.2.5
1.2.6 Check the import plan in the right position Fig. 1.2.6
Suggestion for the setting:- Import the CADD file as link Import Units set to millimetre Positioning set to Auto – Origin to Origin If you checked the Current view only, that means the base plan
will display in the plan view only and not in 3D views or elevations.
Page 57
1.3 Create toposurface
1.3.1 Import survey data Refer to Guideline for handling 3D spartial data from LandsD
1.3.2 Create toposurface by survey point/base plan
1.3.2.1 Create the toposurface by selecting/input the survey point/level point
Fig. 1.3.2.1a Fig. 1.3.2.1b
Page 58
Fig. 1.3.2.1c 1.4 Create Pad to form building platform Fig. 1.4 Summary Index Procedures for site model creation Reference 1.1 Start new project with standard template
(path:- Z:\BIM\Standard Template\ Architectural.rte) Fig. 1.1
1.2 Import base plan (site layout/setting plan) as reference Fig.1.2.1, 1.2.3, 1.2.4, 1.2.5, 1.2.6 1.3 Import survey data to create toposurface Fig. 1.3.2.1a, 1.3.2.1b, 1.3.2.1c 1.4 Create Pad to form building platform Fig. 1.4
2. Procedures for Flat Mix (typical floor plan) model creation 2.1 Start new project with standard template (refer to 1.1) 2.2 Create Flat Mix model
2.2.1 Create reference line or grid line for setting out
Fig. 2.2.1
Page 59
2.2.2 Import standard modular flats to create the flat mix
2.2.2.1 Import the standard modular flats from HA Library (path: z:\Bim\HA Library|\Grouped Model\ Standard Modular Flats)
Fig. 2.2.2.1a
Fig. 2.2.2.1b
Page 60
2.2.2.2. Compose modular flats to create flat mix floor plan
Fig. 2.2.2.2
Tips for compose modular flats Import modular flat as link Use rotate, move, mirror and copy functions to compose the modular
flats Group function is not recommended for composing modular flats, since
it consume a lot of resource)
Page 61
2.2.3 Create common area (i.e. lift core, corridor, staircase & service room etc.) to complete the typical floor plan
Fig.2.2.3
Tips for create common area Create construction line Import Grouped Model as link (e.g. staircase, loft core, service rooms etc.) If no suitable Grouped Model, create the component in field Export the plan view as the typical floor plan for flats mixing
Page 62
Summary Index Procedures for site model creation Reference 2.1 Start new project with standard template
(path:- Z:\BIM\Standard Template\ Architectural.rte) Fig. 1.1
2.2 Create Flat Mix model and export the plan view as the typical floor plan for flats mixing submission
Fig. 2.2.1, 2.2.2.1a, 2.2.2.1b Fig. 2.2.2.2, 2.2.3
3. Procedures for Massing of blocks creation 3.1 Export the typical floor models to 2D CAD files, for more easy to handle in Revit.
Fig. 3.1
Uncheck the xref views on sheets to create single CAD file. If checked, the linked files in Revit model will created as Xreference.
Page 64
3.3 Trace the outline of the building and create the Massing Fig. 3.3
Trace the outline of the building
Create Mass
Create all buildings in the project
Page 65
3.4 Apply colour to the Mass
Fig. 3.4
Edit the Materials in Element Properties of the Mass
1. Select material or duplicate material to create a new material colour 2. Adjust the Transparency if necessary 3. Apply Surface Pattern if necessary
If required to apply different colour to the surface of Mass, use Paint function (e.g. Green R f)
Page 66
3.5 Export 3D views and elevations for submission Fig. 3.5
Tips for creating Mass Give meaningful name to the mass Create mass as Solid Extrustion (most common), if for special shape, you might need
to create mass by other forms Change the material in element properties to assign colour to the mass Use Paint function to apply colour to individual surface of the mass Set Shading with Edges on
Page 67
Summary Index Procedures for site model creation Reference 3.1 Export the typical floor models to 2D CAD files Fig. 3.1 3.2 Import the typical floor plan as reference Fig. 3.2 3.3 Trace the outline of the building and create the Massing Fig. 3.3 3.4 Apply colour to the Mass Fig. 3.4 3.5 Export 3D views and elevations for submission Fig. 3.5
Page 68
Appendix 6 Preparation for Project Design Review Committee (P2) Submission (Same details requirements on Revit models for BC, DDRP1 & DDRP2 Submission) 1. Procedures for site model creation
1.1 Method 1:- Retrieve the site model from previous submission (i.e. AAP, P1, SOM or SPC).
1.2 Method 2:- Create the site model from zero. Refer to Part 1 of Guidelines for creating BIM models for AAP, P1,SOM & SPC submission
2. Procedures for Flat Mix (typical floor plan) model creation
2.1 For P2 & BC Submission:- Retrieve the typical floor plan (LD2 modular flats) from previous submission (i.e. AAP, P1, SOM or SPC).
2.2 For DDRP1 & DDRP2 Submission:- 2.2.1 Retrieve the typical floor plan (LD2 modular flats) from previous submission;
replace the modular flats with LD3 modular flats models. 2.2.2 Input details to common areas.
3. Procedures for creating Ground Floor, First Floor and Roof models 3.1 Method 1:- If you have the CADD files (i.e. AutoCAD files) of the floor plans, insert the floor plan to Revit and base on the CADD drawing to create the model. 3.2 Method 2:- If you do not have any CADD files of the floor plans, start with standard template in Revit, create the model in Revit directly. 4. Procedures for building blocks creation (LD2)
4.1 For elevations creation:- Retrieve the typical floor plan (LD2 modular flats) from previous submission; replace the modular flats with LD1 modular flats models.
4.2 For elevations creation:- Retrieve the typical floor plan (LD2 modular flats) from previous submission.
4.3 For building block creation:-
Tips:- When creating each floor of building model, they should use the same co-ordinate and level system, and then the model will be in right position when linked together.
Page 69
To compose the Ground Floor model, First floor model, Typical Floor model (LD1 modular flats for elevations creation and LD2 modular flats for section creation) and Roof model to form the building block. 4.3.1 Start a new model with standard temple 4.3.2 Create Levels for the building block
Fig. 4.3.2 4.3.3 Import Revit models Fig. 4.3.3
Page 70
4.3.4 Import the Ground Floor + First Floor + Typical Floor (LD1 modular flats – for elevations) or Typical Floor (LD2 modular flats – for sections) + Roof to form the building block Fig. 4.3.4a Ground Floor Fig. 4.3.4b Ground Floor + First Floor
Tips:- For Positioning of the import model, it depended on the setting when you creating the model. Auto - Center to Center & Auto - Origin to Origin are the most common setting for single block. When import the building block to site base model, we should use Auto – By Shared Coordinates
Page 71
Fig. 4.3.4c Ground Floor + First Floor + Typical Floor Fig. 4.3.4d Ground Floor + First Floor + Typical Floor + Roof
Page 73
5. Import the building blocks model to site base model to create the project model Fig. 5a Site Base + Carport + External work Fig. 5b Site Base + Carport + External work + One Domestic Block
Page 74
Fig. 5c Site Base + Carport + External work + Two Domestic Blocks
Fig. 5d Site Sectional Elevation A
Page 75
Fig. 5e Site Sectional Elevation B
6. Other Details
For complex details, please draw in AutoCAD (e.g. aluminium window details, details of expansion joints etc.). If you draw everything in the Revit project models. The application will be corrupted.
Tips:- i) Simply the models to minimum ii) When import huge model (e.g. the domestic block) into the site
model, you might need to unload other link files temporary, and then reload afterward. It can decrease the re-generation time and speed-up the file loading.
iii) Delete all necessary views, elevations and sections. Since each view need resource to re-generate.
iv) Be patient.
Page 76
Appendix 7 Handling 3D Spatial Data from Lands Department in BIM models 1. Import 3ds file (file from Lands Department) to AutoCAD 1.1 3ds file from Lands Department Fig.1.1 1.2 Import 3ds file to AutoCAD 1.2.1 Import to AutoCAD
Fig.1.2.1
Page 79
1.3 Move all elements close to Origin 1.3.1 Select all elements
Fig.1.3.1 1.3.2 Define base point Fig. 1.3.2 1.3.3 Move all elements to the origin Fig. 1.3.3a Fig. 1.3.3b
Page 80
1.4 Re-scale the file to 1:1 (Since the files from Lands Department are 1:1000 or 1:5000, normally 1:1000 )
1.4.1 Select all elements (Refer to 1.3.1)
1.4.2 Define Base point Fig.1.4.2 1.4.3 Re-scale all elements – input scale command
Fig.1.4.3
1.4.4 Input scale factor - 1000
Fig.1.4.4
Page 81
1.5 Separate the terrain and existing building blocks into different files (Save the file before process)
1.5.1 Delete & purge all existing building blocks and save the terrain profile
(If the terrain is not suite as our site formation, you might need further touch-up for the terrain by other application – e.g. Autodesk Civil 3D)
Fig. 1.5.1 1.5.2 Open the original file, delete & purge the terrain and save the existing building blocks
Fig. 1.5.2
Page 82
1.6 Delete the existing building blocks within the site boundary (building in red colour) 1.6.1 Before delete
Plan View
Fig. 1.6.1a 3D View Fig.1.61b
Page 84
2. Works in Revit
2.1 Import the terrain, existing buildings and new layout plan (AutoCAD format) into Revit as reference
Refer to step 1.2 in Guidelines to create Building Information Modelling (BIM) models for AAP, P1, SOM & SPC submission
2.2 Create the massing of new blocks
Refer to step 3.3 & 3.4 in Guidelines to create Building Information Modelling (BIM) models for AAP, P1, SOM & SPC submission
2.3 Export 3D views and elevations for submission/presentation
Refer to step 3.5 in Guidelines to create Building Information Modelling (BIM) models for AAP, P1, SOM & SPC submission
Fig. 2.3a
top related